-acquastop- installation instructions · finishing inox steel weight 1.2 kg ... t.908-996-7710...
TRANSCRIPT
+DESIGN
Pag. 1 - rev.01
BRIGHT 9.0 -ACQUASTOP- Installation instructions
EOS
���� WARNING!!!
Please read the following instructions carefully.
Designplan Lighting, Inc., 79 Trenton Ave., Frenchtown NJ, 08825. T.908-996-7710 F.908-996-7042
Designplan Lighting, Inc., 79 Trenton Ave., Frenchtown NJ, 08825. T.908-996-7710 F.908-996-7042
IMPORTANT:
• Although LED runs on a very low voltage, always cut off the power sup-ply before installing the LED light or subjecting it to maintenance.
• Unauthorised alterations or tampering of the product will invalidate allthe conditions of guarantee.
• This fixture must be installed by a qualified electrician.• Designplan is not resposable if its fixtures are not installed inaccording to local safety standards.
• Data contained in this document may be changed at any moment with-out prior notice.
5.12"
1.63"1.00"
.49"
• Use only Selv type electronic power supply or similar.
ELECTRICAL CONNECTIONS:
• LED lights run at constant current.
• LED lights must be connected in series respecting polarities.
• As for the choice of the power supplies, please consider the current through which they are fed and the max power consumption ofLEDs you have to install.
• The total number of LEDs to be fed must be counted for each singlespot (e.g. 2 spots with 3 LEDs 1W each= 6 LEDs 1W in all= 6W).
• The system must be fed only if all the spots are connected . Theconnection of the single spots with the power supply in voltage maydamage the spot.
• The power supplies must be installed in aerated rooms, far from heatsources. A situation of overworking or a lack of air circulation will notpermit a natural dissipation.
• The electronic power supply is current-stable, therefore it partially com-pensates the voltage-drop problems related to the cable length; wesuggest not to exceed 120ft (30 metres).
• Never use switches on secondary circuit.
NOTES:
• Wire connections must be made with wirenuts or similar.
+DESIGN
Pag. 2 - rev.01 EOS
POWER CONSUMPTION 3x1W; 3x2W; 3x3W; 6x1W
SUPPLY VOLTAGE 350 - 500 - 700 mA
CONNECTION Series connections
N° AND TYPE OF LED USED 3 - 6 power LED
AVERAGE LED LIFE 75% after 50.000 hours
LED COLOURS AVAILABLE White: 5000°K ; 3000°K;
CRI
OPERATING TEMPERATURE -10°C ÷ +45°C
FINISHING Inox steel
WEIGHT 1.2 kg
APPLIANCE CLASS CLASS 2
TYPICAL LUMINOUS FLUX 85 lm/W
FIXING Outer-casing not included (WC0500)
WC0500
1 2
OFF
ON �0
OUTER CASING
WC0500
3 4
5
�
1
2
Acquastop EOS
EOS
BRIGHT 9.0 -ACQUASTOP- Installation instructions
Designplan Lighting, Inc., 79 Trenton Ave., Frenchtown NJ, 08825. T.908-996-7710 F.908-996-7042
Designplan Lighting, Inc., 79 Trenton Ave., Frenchtown NJ, 08825. T.908-996-7710 F.908-996-7042
5.08"
3.94"
WARNING!!! LED LIGHTS MUST BE CONNECTED
IN SERIES RESPECTING POLARITIES. THE SYSTEM MUST BE ENERGIZED ONLY AFTER ALL THE
FIXTURES ARE CONNECTED.
Series connection
PSU Selv
+DESIGN
Pag. 3 - rev.01 EOS
6
7
8 9
SCREW M5x30
SCREW M5x16
O-RING Ø32.99x2.62 Ø88.58x2.62
Note: be very careful when reposition the ring!Center the LEDs with the holes in the glass.
Do not force turning!
Not for permanent submersion installations.
CONNECT WITH RESPECT FOR POLARITY
�
Do not cut !!!
Acquastop
Acquastop EOS
EOS
BRIGHT 9.0 -ACQUASTOP- Installation instructions
Designplan Lighting, Inc., 79 Trenton Ave., Frenchtown NJ, 08825. T.908-996-7710 F.908-996-7042
Designplan Lighting, Inc., 79 Trenton Ave., Frenchtown NJ, 08825. T.908-996-7710 F.908-996-7042
WATERTIGHTCONNECTION