arcat · web viewarcat ... 08210-1

SECTION 08210WOOD DOORS

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2013 - 2014 ARCAT, Inc. - All rights reserved

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Architectural Interior Doors:1. Wood veneer faced doors.2. High pressure decorative laminate faced doors.3. Durable surfaces face doors.4. Paintable surface faced doors.5. Low pressure decorative laminate faced doors.6. Molded panel doors.7. Radiation shielded wood doors.8. Acoustic rated wood doors.9. Stile and rail doors, paneled stile and rail wood doors.10. MDF doors, solid panel and stile and rail.

B. Jambs and casings.

1.2 RELATED SECTIONS

A. Section 06100 - Rough Carpentry.

B. Section 06200 - Finish Carpentry.

C. Section 08100 - Metal Doors and Frames.

D. Section 08710 - Door Hardware.

E. Section 08800 - Glass and Glazing.

F. Section 09900 - Paints and Coatings.

G. Section 13090 - Radiation Protection.

1.3 REFERENCES

A. American National Standards Institute (ANSI):1. ANSI A 208.1 - Standard for Particleboard.2. ANSI A 208.2 - Standard for Medium Density Fiberboard for Interior Use.

B. Window and Door Manufacturers Association (WDMA):1. WDMA I.S. 1A-13 - Industry Standard for Interior Architectural Wood Flush Doors.2. WDMA I.S. 6A-13 - Industry Standard for Interior Architectural Stile and Rail Doors.

C. Architectural Woodwork Standards (AWS) - Current Edition.

D. National Fire Protection Association (NFPA):

08210-1

1. NFPA 80 - Standard for Fire Doors and Other Opening Protectives.2. NFPA 252 - Standard Methods of Fire Tests of Door Assemblies.

E. Underwriters' Laboratories (UL):1. UL 10B - Fire Tests of Door Assemblies.2. UL 10C - Positive Pressure Fire Tests of Door Assemblies.

F. ITS (Warnock Hersey): Certification Listings for Fire Doors.

G. Forest Stewardship Council (FSC): Guidelines for environmentally certified wood doors.

H. US Green Building Council (USGBC): LEED - Leadership in Energy and Environmental Design rating system.

1.4 SUBMITTALS

A. Submit under provisions of Section 01300.

B. Product Data: Manufacturer's product construction data, hardware attachment performance data, specifications and installation instructions for each type of wood door, including details of core, raised panel (if applicable) and edge construction, trim for lite openings and similar components:1. Preparation instructions and recommendations.2. Storage and handling requirements and recommendations.3. Cleaning methods.

C. Product Certification: Provide documents showing compliance to the following WDMA door attributes, validating the specified WDMA Performance Duty Level:1. Adhesive Bonding Durability: WDMA TM-6.2. Cycle Slam: WDMA TM-7.3. Hinge Loading: WDMA TM-8.4. Screw Holding: WDMA TM-10.

a. Door Face.b. Vertical Door Edge.

D. LEED Submittals: The following project data and calculation information shall be submitted to document prerequisite compliance.1. Product Data: for Credit MR-4. For products having recycled content, provide

documentation indicating percentage by weight of post-consumer and pre-consumer/post-industrial recycled content.a. Provide statement indicating cost for each material having recycled content.b. Provide third party certification or manufacturer's written statement for recycled

content.2. Product Data for Credit MR 5: For products and materials that comply with

requirements for regional materials, documents indicating location of material manufacturer and point of extraction, harvest, or recovery for each raw material that contributes towards this credit. Include statement indicating distance to Project, cost for each regional material, and fraction by weight that is considered regional.

3. Certificates for Credit MR 6, LEED Core And Shell and Credit MR 7: Provide the project's total project cost (for application of 45 percent default factor) or total materials cost. Complete the rapidly renewable materials calculation template provided. Provide an optional narrative for any special circumstances. A Vendor is defined as the company that sells wood products to building project contractors or subcontractors. Each vendor invoice shall conform to the following requirements:.a. Each wood product shall be identified on a line-item basis;b. FSC products shall be identified as such on a line-item basis and shall be

identified as "FSC 100%," "FSC Mix Credit," or "FSC Mix[NN]%".

08210-2

c. The dollar value of each line item shall be shown;d. The vendor's chain-of-custody (COC) number shall be shown on any invoice

that includes FSC products.4. Product Data for Credit IEQ 4.4: For adhesives and composite wood products,

documentation indicating that product contains no added urea formaldehyde.5. LEED for Schools Laboratory Test Reports for Credit IEQ 4.4: For composite wood

products, documentation indicating that products comply with the testing and product requirements of the California Department of Health Services' "Standard Practice for the Testing of Volatile Organic Emissions from Various Sources Using Small-Scale Environmental Chambers." All composite wood and agrifiber products shall meet this requirement. In addition to the above, provide products that are third party certified through SCS Indoor Advantage Gold.a. All composite wood and agrifiber products shall meet this requirement.b. Provide products that are third party certified to SCS Global Services - SCS

Indoor Advantage Gold.6. Provide Data for Credit IEQ 9 - Enhanced Acoustical Performance: Building shell,

classroom partitions and other core learning space partitions meet STC (Sound Transmission Class) requirements of ANSI S12.60-2002. Section 4.5.5 entry doors into classrooms and other core learning spaces.

E. Shop Drawings: Indicate location, size, and hand of each door; elevation of each kind of door; construction details and the following:1. Dimensions and locations of blocking.2. Dimensions and locations of mortises and holes for hardware.3. Dimensions and locations of cutouts.4. Undercuts.5. Requirements for veneer matching.6. Doors to be factory finished and finish requirements.7. Fire-protection ratings for fire-rated doors.

F. Verification Construction Samples:1. Construction Samples: Corner sections with door faces, raised panels, sticking profile,

edges, and core representative of the actual door types specified, in manufacturer's standard size for samples.

2. For each wood species and transparent finish, provide set of three samples showing typical examples of color and grain to be expected in finished work.

3. Provide construction samples of doors, approximately 5 by 5 inches (125 by 125 mm), with door faces and vertical edges representing actual construction to be used.a. Flush Doorsb. Stile and Rail Doors

G. Verification Finishing Samples:1. Factory finishes applied to actual door face materials, approximately 8 by 10 inches

(200 by 250 mm), for each material and finish.2. Color Samples: Two samples, minimum 4 inches (100 mm) x 6 inches (150 mm), on

veneer or paintable surface representing actual products and finishes specified.

1.5 QUALITY ASSURANCE

A. Manufacturer's Qualifications: Company specializing in manufacturing products specified herein with a minimum of five years documented experience.1. A qualified vendor that is a member in good standing of the Window and Door

Manufacturers Association.2. A qualified manufacturer that is certified for chain of custody by an FSC-accredited

certification body.a. Doors requiring environmental certification will be marked with Forest

Stewardship Council (FSC) Chain of Custody Certificate Code to ensure wood

08210-3

components come from certified forests and are processed by certified chain-of-custody manufacturers.

b. Vendor Qualifications: A vendor that is certified for chain of custody by an FSC-accredited certification body. Vendors installing FSC doors are not required to be FSC COC certified unless modifying the product beyond what is required for installation purposes.

B. Single Source Requirements: Doors shall be supplied from a single manufacturing organization.

1.6 DELIVERY, STORAGE, AND HANDLING

A. Deliver, store and handle materials and products in strict compliance with manufacturer's warranty and recommendations of industry standards.

B. Store materials in manufacturer's original sealed, labeled packaging until ready for installation and in accordance with manufacturer's instructions. Protect from damage.

C. Store and protect doors in accordance with manufacturer's warranty including but not limited to the following.1. Compliance: WDMA Standards.2. Store doors flat and off the floor on a level surface in a dry, well-ventilated building. Do

not store on edge. Protect/cover doors from dirt, water and abuse.3. Certain wood species are light sensitive. Protect doors from exposure to light (artificial

or natural) after delivery.4. When handling doors, always lift and carry. Do not drag across other doors or

surfaces. Handle with clean hands or gloves.5. Each door will be marked on top rail with opening number.

1.7 PROJECT CONDITIONS

A. Maintain environmental conditions (temperature, humidity and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.1. Environmental Limits: Do not store or install doors until spaces are enclosed and

weather tight, wet work in spaces is complete and dry, and HVAC system is operating and maintaining temperature between 50 and 90 degrees F, and relative humidity between 25 and 55 percent during remainder of construction period.

1.8 WARRANTY

A. Special Warranty: Manufacturer agrees to repair or replace doors that fail in materials or workmanship within specified warranty period.1. Failures include, but are not limited to, the following:

a. Warping (bow, cup, or twist) more than 1/4 inch (6.4 mm) in a 42-by-84-inch (1067-by-2134-mm) section.

b. Telegraphing of core construction in face veneers exceeding 0.01 inch in a 3-inch (0.25 mm in a 76.2-mm) span.

2. Warranty shall also include installation and finishing that may be required due to repair or replacement of defective doors.

3. Warranty Period for Solid-Core Interior Doors: Life of installation.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Acceptable Manufacturer: Marshfield, which is located at: 1401 E. 4th St.; Marshfield, WI

08210-4

54449; Toll Free Tel: 800-869-3667; Tel: 800-869-3667; Fax: 715-384-3802; Email:request info ([email protected]); Web:www.marshfielddoors.com

B. Substitutions: Not permitted.

C. Requests for substitutions will be considered in accordance with provisions of Section 01600.

2.2 DOORS - GENERAL

A. Quality Assurance Requirements:1. Flush Wood Doors: Comply with WDMA I.S.1A-13, "Industry Standard for Interior

Architectural Wood Flush Doors."2. Stile and Rail Wood Doors: Comply with WDMA I.S.6A-13, "Industry Standard for

Interior Architectural Stile and Rail Doors."

B. WDMA Performance Duty Level:1. Heavy duty.2. Extra heavy duty.

C. Wood-Based Particleboard-Core Doors, non-rated 20 minute: Provide wood-based particleboard core doors with a minimum density per ANSI A208.1, Grade LD-2 as required to meet WDMA Performance Duty level required without added blocking.

D. Structural-Composite-Lumber-Core Doors, non-rated 20 minute:1. Provide Structural Composite Lumber core as required to meet WDMA Performance

Duty Level required.2. Provide Structural Composite Lumber core for doors with glass openings as required

to meet stile dimensions shown on door schedule and elevations.

E. Staved Lumber Core Doors, non-rated 20 minute: Made with any combination of blocks or strips of wood, not more than 2-1/2 inches (64 mm) wide, of one species of wood glued together (in butcher block fashion), with joints staggered in adjacent rows.

F. Fire-Rated Wood Doors: Doors complying with NFPA 80 that are listed and labeled by a qualified testing agency, for fire-protection ratings indicated, based on testing at positive pressure according to NFPA 252 or UL 10C required by Authority Having Jurisdiction (AHJ).1. Label Certification: Doors requiring fire-rating will carry either UL or ITS (Warnock

Hersey) label. Manufacturer's certification labels may be used for door size variations if approved by AHJ (Authority Having Jurisdiction).

2. Temperature-Rise Limit: Where indicated and at vertical exit enclosures and exit passageways, provide doors that have a maximum transmitted temperature end point of not more than 250 degrees F (121 degrees C)] above ambient after 30 minutes of standard fire-test exposure.

3. Cores: Provide wood fiber or mineral fire-resistant composite core as needed to provide fire-protection rating indicated.

4. Blocking: Provide composite blocking approved for use in doors of fire-protection ratings indicated as needed to eliminate through-bolting hardware.

5. Edge Construction: Category A - intumescent included in door construction where required.

6. Edge Construction: Category B - intumescent applied to frames by door installer where required.

7. Pairs: Provide fire-retardant stiles that are listed and labeled for applications indicated without formed-steel edges and astragals.

8. Pairs: Provide formed-steel edges and astragals with intumescent seals as required.a. Provide steel edges and astragals primed for field painting.b. Provide veneer wrapped steel edges and astragals. Veneer shall be same

08210-5

specie as face.c. Finish steel edges and astragals with baked enamel, color as selected from

manufacturer's standard offering.d. Provide stainless steel edges and astragals.

G. ACOUSTIC DOORS1. Interior Solid-Core Doors:2. Basis-of-Design Product: Subject of compliance with requirements, provide

Marshfield; "SonaShield" or a comparable product by one of the following:a. Algoma.b. Mohawk.c. Baillargeon.

3. Provide core indicated or special construction core as required to meet STC rating indicated on door schedule. STC ratings shall be tested as operable.

4. Provide Gasketing, door shoe or mortise door bottom as required to meet manufacturers tested acoustic rating.

5. Hollow metal frames shall be fully grouted or packed with mineral wool where acoustic rated wood doors are installed.

6. The Sound Transmission Class (STC) specified shall be certified by the manufacturer to be based on tests conducted at an independent testing agency in accordance with ASTM E90-90 and E413-87.

7. Acoustic-Rated Doors: Provide STC Rating of 33-35.8. Acoustic-Rated Doors: Provide STC Rating of 36-41.9. Acoustic-Rated Doors: Provide STC Rating of 42-47.10. Doors shall match design of wood veneer doors as specified and scheduled.11. Doors shall match design of high pressure decorative laminate doors as specified and

scheduled.12. Doors shall match design of durable surfaces doors as specified and scheduled.

H. RADIATION-SHIELDED DOORS1. Interior Solid-Core Doors:2. Basis-of-Design Product: Subject of compliance with requirements, provide

Marshfield; "DuraShield" or a comparable product by one of the following:a. Algoma.b. Mohawk.

3. Lead Thickness: 1/16 inch (1.6 mm).4. Lead Thickness: 1/8 inch (3.2 mm).5. Lead Thickness: As indicated in door schedule.6. Provide wood/lead astragals on radiation shielded pairs in lead thickness indicated.

Finish astragals to match face finish.7. Doors shall match design of wood veneer doors as specified and scheduled.8. Doors shall match design of high pressure decorative laminate doors as specified and

scheduled.9. Doors shall match design of durable surfaces doors as specified and scheduled.

I. Sustainability Requirements:1. Regional Materials: Where available based on inclusive list of approved

manufacturers, flush wood doors shall be manufactured within 500 miles (800 km) of Project site from materials that have been extracted, harvested, or recovered, as well as manufactured, within 500 miles (800 km) of Project site.

2. Certified Wood: Flush wood doors shall be certified according to FSC STD-01-001, "FSC Principles and Criteria for Forest Stewardship," and to FSC STD-40-004, "FSC Standard for Chain of Custody Certification." FSC claims are to be based on "new" wood contribution only. All recycled, reclaimed, and recovered material, even if it is FSC Recycled, shall be applied towards the MR 4 credit.

3. Low-Emitting Materials: Fabricate doors with adhesives and composite wood products

08210-6

that do not contain added urea formaldehyde.4. Low-Emitting Materials: Fabricate doors that comply with the testing and product

requirements of the California Department of Health Services' "Standard Practice for the Testing of Volatile Organic Emissions from Various Sources Using Small-Scale Environmental Chambers." All composite wood and agrifiber products shall meet this requirement. Prefer products that are third party certified through SCS Indoor Advantage Gold.a. All composite wood and agrifiber products shall meet this requirement.b. Provide products that are third party certified to SCS Global Services - SCS

Indoor Advantage Gold.

J. Smoke and Draft Control Door Assemblies: Listed and labeled for smoke and draft control, based on testing according to UL 1784.

K. Louvers in Standard Doors:1. Type: Wood, round slat.2. Type: Wood, flat slat.3. Type: Wood, light proof.4. Type: Metal.5. Type: Fusible link operator.

2.3 WOOD VENEER FACED DOORS

A. Interior Solid-Core Doors:1. Basis-of-Design Product: Subject to compliance with requirements, provide

Marshfield; "Signature Series" or a comparable product by one of the following:a. Algoma.b. Mohawk.c. Baillargeon.

2. Veneer Grade: AA (reserved for high-end specialty applications).3. Veneer Grade: A (best suited for most commercial applications).4. Species: African Mahogany.5. Species: Aniegre.6. Species: Select white ash.7. Species: Select white birch.8. Species: Cherry.9. Species: Select white maple.10. Species: Red oak11. Species: White oak12. Species: Sapele13. Species: Walnut14. Cut: Rotary cut.15. Cut: Plain sliced (flat sliced).16. Cut: Quarter sliced.17. Cut: Rift cut.18. Match between Veneer Leaves: Book match.19. Match between Veneer Leaves: Slip match.20. Assembly of Veneer Leaves on Door Faces: Center-balance match.21. Assembly of Veneer Leaves on Door Faces: Balance match.22. Assembly of Veneer Leaves on Door Faces: Running match.23. Pair and Set Match: Provide for doors hung in same opening or separated only by

mullions. Provide sets up to four doors.24. Special Veneer Selection: None Required.25. Special Veneer Selection: _______________.26. Transom Match: Continuous match.27. Exposed Vertical Edges: Veneer of same species as face, bonded to structural

08210-7

composite lumber, concealing edges of crossband.28. Exposed Vertical Edges: Hardwood, of same or compatible species as face, minimum

thickness of 1/2 inch (13 mm), bonded to structural composite lumber, leaving edges of crossband exposed.

29. Exposed Vertical Edges: 1/8 inch (3.2 mm) high impact edge bonded to structural composite lumber, color or wood grain as selected from manufacturer's standard offering.

30. Horizontal Edges: Structural composite lumber.a. Seal horizontal edgebands to provide cleanable surfaces.b. Bond smooth acrylic modified vinyl edgeband to structural composite lumber,

providing cleanable surface.31. Core: As specified or required by schedule.32. Construction: Five plies. Stiles and rails are bonded to core, and then entire unit is

abrasive planed before veneering.33. WDMA I.S.1-A Performance Grade: Extra Heavy Duty.34. WDMA I.S.1-A Performance Grade: Heavy Duty35. WDMA I.S.1-A Performance Grade: As scheduled.36. All doors shall meet specified WDMA Performance Duty Level, including face screw

holding requirement. Surface applied hardware shall be installed with screws; through bolts are not acceptable.

37. All doors shall meet specified WDMA Performance Duty level, with the exception of face screw holding requirement. Surface applied hardware shall be installed with through bolts.

2.4 HIGH PRESSURE DECORATIVE LAMINATE FACED DOORS


Marshfield; "Marquis Series" or a comparable product by one of the following:a. Algoma.b. Mohawk.c. Baillargeon.

2. Grade: Premium.3. Grade: Custom.4. HPDL Faces: High-pressure decorative laminates complying with NEMA LD 3,

a. Grade HGS. Vertical and post formable grade laminates are not acceptable.b. Grade VGS. Post formable grade laminates are not acceptable.

5. Colors, Patterns, and Finishes: As indicated or scheduled.6. Colors, Patterns, and Finishes: As selected from Wilson Art full range of products.7. Colors, Patterns, and Finishes: As selected from Pionite full range of products.8. Colors, Patterns, and Finishes: As selected from Nevamar full range of products.9. Colors, Patterns, and Finishes: As selected from Laminart full range of products.10. Colors, Patterns, and Finishes: As selected from Formica full range of products.11. Colors, Patterns, and Finishes: As selected from Abet Laminati full range of products.12. Exposed Vertical Edges: High-pressure decorative laminate that matches faces,

applied to structural composite lumber stile after faces.13. Exposed Vertical Edges: 1/8 inch (3.2 mm) impact-resistant edging, applied after

faces, color selected from manufacturer's standard offering.14. Horizontal Edges: Structural composite lumber.

a. Seal horizontal edgebands to provide cleanable surfaces.b. Bond smooth acrylic modified vinyl edgeband to structural composite lumber,

providing cleanable surface.15. Core: As specified or required by schedule.16. Construction: Three plies. Stiles and rails are bonded to core, and then entire unit is

abrasive planed before faces are applied. Crossbands may be used where required.17. WDMA I.S.1-A Performance Grade: Extra Heavy Duty.

08210-8

18. WDMA I.S.1-A Performance Grade: Heavy Duty19. WDMA I.S.1-A Performance Grade: As indicated.20. All doors shall meet specified WDMA Performance Duty Level, including face screw



2.5 DURABLE SURFACES FACED DOORS

A. Interior Solid-Core Doors:1. Basis-of-Design Product: Subject of compliance with requirements, provide

Marshfield; "DurableDoor" or a comparable product by one of the following:a. Algoma.b. Baillargeon.

2. Grade: Premium.3. Grade: Custom.4. WDMA Performance Grade I.S.1-A: Extra Heavy Duty.5. Faces: Chemical-and stain-resistant, high-impact, acrylic modified vinyl faces.6. Color as scheduled or indicated.7. Vertical edges shall be 1/8 inch (3.2 mm) matching high impact acrylic material

bonded to structural composite lumber. Removable edges are not permitted.8. Horizontal Edges: Structural composite lumber


providing cleanable surface.9. Core: As specified or required by schedule.10. Construction: Five plies. Stiles and rails are bonded to core, then entire unit is

abrasive planed before faces and crossbands are applied.

2.6 PAINTABLE SURFACE DOORS


Marshfield; "Impressions Series" or a comparable product by one of the following:a. Algoma.b. Mohawk.c. Baillargeon.

2. Grade: Premium.3. Grade: Custom.4. Veneer: Medium Density Overlay (MDO).

a. Apply MDO directly to high-density fiberboard (HDF) cross bands.5. Veneer: Paint-grade hardwood.

a. Material: Birch.6. Exposed Vertical Edges: Any closed-grain hardwood veneer, bonded to structural

composite lumber.7. Exposed Vertical Edges: Any closed grain hardwood, minimum of 1/2 inch (13 mm),

bonded to structural composite lumber.8. Exposed Vertical Edges: 1/8 inch (3.2 mm) high impact edge bonded to structural

composite lumber, color as selected from manufacturer's standard offering.9. Horizontal Edges: Structural composite lumber.


providing cleanable surface.10. Core: As specified or required by schedule.

08210-9

11. Construction: Five plies. Stiles and rails are bonded to core, one piece high density fiberboard is laminated to each side before veneering.

12. WDMA I.S.1-A Performance Grade: Extra Heavy Duty.13. WDMA I.S.1-A Performance Grade: Heavy Duty.14. WDMA I.S.1-A Performance Grade: As indicated.15. All doors shall meet specified WDMA Performance Duty Level, including face screw



2.7 LOW PRESSURE DECORATIVE LAMINATE DOORS

A. Interior Solid-Core Doors: Basis-of-Design Product: Subject of compliance with requirements, provide Marshfield; "Perfect Match".1. Grade: Premium.2. Grade: Custom.3. WDMA Performance Grade I.S.1-A: Heavy Duty.4. WDMA Performance Grade I.S.1-A: Extra Heavy Duty.5. Faces: Low Pressure Decorative Laminate complying with LMA (Laminating Materials

Association) document LMA, latest edition, Product Standard and Typical Physical Properties of Decorative Overlays. Face as selected from manufacturer's full range of wood grain patterns.

6. Vertical edges shall be matching high impact acrylic material bonded to structural composite lumber.

7. Horizontal Edges: Structural composite lumber.a. Seal horizontal edgebands to provide cleanable surfaces.b. Bond smooth acrylic modified vinyl edgeband to structural composite lumber,

providing cleanable surface.8. Core: Wood-based particleboard.9. Construction: Five plies. Stiles and rails are bonded to core, then entire unit is

abrasive planed before faces and crossbands are applied.

2.8 MOLDED PANEL PAINTED DOORS

A. Interior Solid-Core Doors:1. Contour Series as manufactured by Marshfield, Inc.

2.9 PANELED DOORS

A. Paneled Stile and Rail Wood Doors.1. Basis-of-Design Product: Subject of compliance with requirements, provide

Marshfield; "Stile and Rail" or a comparable product by one of the following:a. Algoma.b. Mohawk.

B. Stile and Rail Doors:1. Door Thickness: 1-3/8 inches (35 mm).2. Door Thickness: 1-3/4 inches (44 mm).3. Door Thickness: 2 inches (51 mm).4. Door Thickness: 2-1/4 inches (57 mm).5. Veneer Species: Clear Alder.6. Veneer Species: Ash.7. Veneer Species: White Birch.8. Veneer Species: Natural Birch.9. Veneer Species: Plain Sliced Cherry.

08210-10

10. Veneer Species: Quartered Cherry.11. Veneer Species: Hickory.12. Veneer Species: Plain Sliced African Mahogany.13. Veneer Species: White Maple.14. Veneer Species: Clear Pine.15. Veneer Species: Knotty Pine.16. Veneer Species: Stain Grade Poplar.17. Veneer Species: Select White Poplar.18. Veneer Species: Plain Sliced Red Oak.19. Veneer Species: Rift Red Oak.20. Veneer Species: Quartered Red Oak.21. Veneer Species: Walnut.22. Veneer Species: Plain Sliced White Oak.23. Veneer Species: Rift Cut White Oak.24. Veneer Species: Quartered White Oak.25. Finish: Factory finished.26. Finish: Field/shop finished.27. Door Design: Glazed.

a. Glass: Glue Chip,b. Glass: Beveled.c. Glass: Rain.d. Glass: Obscure.e. Glass: Water.f. Glass: Reeded.g. Glass: White Hue Opaque.h. Glass: V-Groove.i. Glass: Clear Tempered.j. Factory-Glazed Fire-Rated Doors: Pyroswiss - Standard.k. Factory-Glazed Fire-Rated Doors: Keralite FRF.l. Factory-Glazed Fire-Rated Doors: Firelite NT Premium.m. Factory-Glazed Fire-Rated Doors: Firelite Plus.

28. Door Design: French.a. Design: K 3580.b. Design: K 36700.c. Design: K 3700.d. Design: K 3750.e. Design: K 3800.f. Design: K 3820.g. Design: K 3830.h. Design: K 3840.i. Design: K 6010.j. Design: K 6020.k. Design: K 6080.l. Design: K 6090.m. Design: K 6310.

29. Door Design: Louvered.a. Design: Chevron.b. Design: Flat.

30. Door Design: Flat Panel.a. Design K 3040A.b. Design K 3050.c. Design K 4010R.d. Design K 5020L.e. Design K 5300.f. Design K 5310A.g. Design K 5320R.

08210-11

h. Design K 5400L.i. Design K 5410A.j. Design K 5500R.k. Design K 5660.l. Design K 6000R.m. Design K 6010.n. Design K 6020.o. Design K 6040.p. Design K 6050.q. Design K 6096.r. Design K 6098.s. Sticking: Square.t. Sticking: Mission.

31. Door Design: Raised Panel.a. Design K 3030.b. Design K 3040.c. Design K 3050.d. Design K 3060.e. Design K 3070.f. Design K 3380.g. Design K 3090.h. Design K 3120.i. Design K 3180.j. Design K 3190.k. Design K 3220.l. Design K 4010.m. Design K 5020.n. Design K 5300.o. Design K 5310.p. Design K 5320.q. Design K 5400.r. Design K 5410.s. Design K 5500.t. Design K 5600.u. Design K 5610.v. Design K 5660.w. Design K 5810.x. Design K 5930.y. Design K 6000.z. Sticking: Ogee.aa. Sticking: Ovolo.

32. Acoustical Application:a. Non-Rated door - STC 32 with or without glass: Provide Pemko Gasketing.b. Non-Rated door or 20 minute door - Special Construction STC 33: Operable

with Pemko Gasketing.c. 90-minute fire door - STC 39: Operable with Pemko Gasketing.

2.10 MDF SOLID PANEL DOORS

A. Solid Panel "Simulated Stile and Rail" Wood Doors.1. Basis-of-Design Product: Subject of compliance with requirements, provide

Marshfield; "Carte Blanche" or a comparable product by one of the following:a. Algoma.b. Mohawk.

B. MDF Solid Panel:

08210-12

1. Size and Panel Types: Refer to drawings and specifications.2. WDMA - Performance Duty Level: Extra Heavy Duty. Product does not require

blocking for surface hardware.3. Door Thickness: 1-3/8 inches (35 mm).4. Door Thickness: 1-3/4 inches (44 mm).5. Door Core: Non-Rated and 20 Minute: Medium Density Fiberboard.

a. Metal Vision Frames for 20 Minute Rated Doors: Total area not to exceed 1,296 sq. in. (0.84 sq. m.) of visible glass or one continuous dimension of 30 inches (762 mm) W or 54 inches (1372 mm) H.

6. Door Core: 45, 60, and 90 Minute: Fire Resistant Composite.7. Finish: Factory primed.8. Finish: Factory painted.9. Door Design: French.

a. Muntin: TDL (true-divided lites) with individual pieces of glassb. Muntin: SDL (simulated-divided lites) with a single piece of glass and surface

applied grilles to each side.c. Design: CB 101 (10 lite tall).d. Design: CB 101 (12 lite tall).e. Design: CB 101 (15 lite tall).f. Design: CB 101 (18 lite tall).g. Glass: Glue Chip,h. Glass: Beveled.i. Glass: Rain.j. Glass: Obscure.k. Glass: Water.l. Glass: Reeded.m. Glass: White Hue Opaque.n. Glass: V-Groove.o. Glass: Clear Tempered.p. Factory-Glazed Fire-Rated Doors: Pyroswiss - Standard.q. Factory-Glazed Fire-Rated Doors: Keralite FRF.r. Factory-Glazed Fire-Rated Doors: Firelite NT Premium.s. Factory-Glazed Fire-Rated Doors: Firelite Plus.

10. Door Design: Louvered.a. Design: Vented Flat.b. Design: False louver both sides.c. Design: False louver one sides.

11. Door Design: Flat Panel.a. As indicated or required by Drawings and Schedules.

12. Door Design: Simulated Raised Panel.a. Design CB 101.b. Design CB 102.c. Design CB 102R.d. Design CB 103.e. Design CB 104.f. Design CB 104R.g. Design CB 105.h. Design CB 106.i. Design CB 106R.j. Design CB 107R.k. Design CB 108.l. Design CB 109.m. Design CB 110.n. Design CB 201.o. Design CB 202.p. Design CB 202R.

08210-13

q. Design CB 203.r. Design CB 203R.s. Design CB 205.t. Design CB 206.u. Design CB 206R.v. Design CB 207.w. Design CB 207R.x. Design CB 208.y. Design CB 209.z. Design CB 210.aa. Design CB 211.bb. Design CB 212.cc. Design CB 212R.dd. Design CB 213R.ee. Design CB 214.ff. Design CB 215.gg. Design CB 216.hh. Design CB 216R.ii. Design CB 217.jj. Design CB 217R.kk. Design CB 218.ll. Design CB 219.mm. Design CB 220.nn. Design CB 221.oo. Design CB 222.pp. Design CB 301.qq. Design CB 302.rr. Design CB 302R.ss. Design CB 303.tt. Design CB 303R.uu. Design CB 304.vv. Design CB 304R.ww. Design CB 305.xx. Design CB 306.yy. Design CB 306R.zz. Design CB 307.aaa. Design CB 307R.bbb. Design CB 308.ccc. Design CB 309.ddd. Design CB 310.eee. Design CB 311.fff. Design CB 312.ggg. Design CB 312R.hhh. Design CB 313R.iii. Design CB 314.jjj. Design CB 315.kkk. Design CB 316.lll. Design CB 316R.mmm. Design CB 317.nnn. Design CB 317R.ooo. Design CB 318.ppp. Design CB 319.qqq. Design CB 320.rrr. Design CB 320R.sss. Design CB 321.ttt. Design CB 321R.

08210-14

uuu. Design CB 322.vvv. Design CB 323.www. Design CB 323R.xxx. Design CB 401.yyy. Design CB 402.zzz. Design CB 402R.aaaa. Design CB 403.bbbb. Design CB 403R.cccc. Design CB 404.dddd. Design CB 404R.eeee. Design CB 406.ffff. Design CB 406R.gggg. Design CB 407.hhhh. Design CB 407R.iiii. Design CB 408.jjjj. Design CB 409.kkkk. Design CB 410.llll. Design CB 411.mmmm. Design CB 412.nnnn. Design CB 413.oooo. Design CB 414.pppp. Design CB 501.qqqq. Design CB 502.rrrr. Design CB 502R.ssss. Design CB 503.tttt. Design CB 503R.uuuu. Design CB 504.vvvv. Design CB 504R.wwww. Design CB 505.xxxx. Design CB 506.yyyy. Design CB 506R.zzzz. Design CB 507R.aaaaa. Design CB 508.bbbbb. Design CB 509.ccccc. Design CB 510.ddddd. Design CB 511.eeeee. Design CB 512.fffff. Design CB 512R.ggggg. Design CB 513.hhhhh. Design CB 513R.iiiii. Design CB 514.jjjjj. Design CB 515.kkkkk. Design CB 601.lllll. Design CB 602.mmmmm. Design CB 602R.nnnnn. Design CB 603.ooooo. Design CB 604.ppppp. Design CB 604R.qqqqq. Design CB 605.rrrrr. Design CB 606.sssss. Design CB 606R.ttttt. Design CB 607.uuuuu. Design CB 608.vvvvv. Design CB 608R.wwwww. Design CB 609.xxxxx. Design CB 610.

08210-15

yyyyy. Design CB 611.zzzzz. Design CB 701.aaaaaa. Design CB 702.bbbbbb. Design CB 702R.cccccc. Design CB 703.dddddd. Design CB 704.eeeeee. Design CB 704R.ffffff. Design CB 801.gggggg. Design CB 802.hhhhhh. Design CB 802R.iiiiii. Design CB 803.jjjjjj. Design CB 804.kkkkkk. Design CB 804R.llllll. Design CB 805.

2.11 LIGHT FRAMES AND LOUVERS

A. Factory Glazing: Refer to Section 08800 "Glazing" for glass view panels in doors.1. Factory install glass in all factory finish doors.2. Fill glazing bead nail holes in factory finished doors.3. Cut-out only.4. Frames for Light Openings in MDF Solid Panel Doors:

a. Wood Beads: Provide manufacturer's standard flush wood beads unless otherwise indicated.

b. Wood Beads: Provide manufacturer's standard lip type wood beads unless otherwise indicated.

c. Steel Frame: Provide manufacture standard metal vision frames.d. Profile: Manufacturer's standard shape.

5. Light Openings in Fire-Rated Doors: Manufacturer's standard metal frame formed of 0.048 inch (1.2-mm) thick, cold-rolled steel sheet approved for use in doors of fire-protection rating indicated.a. Factory primed for paint.b. Factory primed for paint with baked-enamel- or powder-coated finish.

B. MDF Louvers:1. Door manufacturer's standard MDF louvers unless otherwise indicated.2. Louver Type: Vented.3. Louver Type: False.4. Louver Type: Chevron.

2.12 FABRICATION

A. Factory machine doors for finish hardware in accordance with hardware requirements and dimensions. Do not machine for surface hardware.

B. Factory prefit doors for frame opening dimensions identified on shop drawings.

2.13 SHOP PRIMING

A. Doors for Opaque Finish: Shop prime faces and vertical edges with one coat of wood primer specified in painting specification section.

2.14 FACTORY FINISHING

A. General: Comply with referenced quality standard for factory finishing. Complete fabrication, including fitting doors for openings and machining for hardware that is not surface applied, before finishing.

08210-16

1. Finish faces and vertical edges, seal top and bottom edges as required for warranty purposes

2. Factory finish doors.3. Factory finish doors that are indicated to receive transparent finish.4. Factory finish doors where indicated in schedules or on Drawings as factory finished.

B. Transparent Finish:1. Grade: Premium.2. Grade: Custom.3. Finish System

a. Manufacturer's standard UV cured polyurethane, equal to WDMA TR-6 catalyzed polyurethane.

b. Other: Specify.c. Staining: Match Architect's sample.d. Staining: As selected by Architect from manufacturer's full range.e. Staining: None required.

4. Sheen:a. Satin.b. Other: Specify.

C. Opaque Finish:1. Grade: Premium.2. Grade: Custom.3. Finish: Water Based Paint.

a. Color: Match Architect's sample.b. Color: As selected by Architect from manufacturer's full range.

4. Sheen:a. Satin.b. Other: Specify.

PART 3 EXECUTION

3.1 EXAMINATION AND PREPARATION

A. Examine and prepare openings and substrates using the methods recommended by manufacturer for achieving best result for the substrates under project conditions.1. Confirm that frames comply with type, size, location and swing requirements and that

they are installed plumb and square.2. Inspect doors for any damage, manufacturing defects or pre-finish inconsistency prior

to installation, including but not limited to wrong color or poor finish.

B. Do not proceed with installation until openings and substrates have been prepared using the methods recommended by manufacturer and deviations from manufacturer's recommended tolerances are corrected. Commencement of installation constitutes acceptance of conditions.

C. If preparation is the responsibility of another installer, notify Architect in writing of deviations from manufacturer's recommended installation tolerances and conditions.

3.2 INSTALLATION

A. Hardware: For installation, refer to Section 08710 "Door Hardware."

B. Installation Instructions: Install doors to comply with manufacturer's written instructions and referenced quality standard, and as indicated.1. Install fire-rated doors according to NFPA 80.2. Install smoke- and draft-control doors according to NFPA 105.

08210-17

C. Job-Fitted Doors: Align and fit doors in frames with uniform clearances and bevels as indicated below; do not trim stiles and rails in excess of limits set by manufacturer or permitted for fire-rated doors. Machine doors for hardware. Seal edges of doors, edges of cutouts, and mortises after fitting and machining.1. Clearances: Provide 1/8 inch (3.2 mm) at heads, jambs, and between pairs of doors.

Provide 1/8 inch (3.2 mm) from bottom of door to top of decorative floor finish or covering unless otherwise indicated. Where threshold is shown or scheduled, provide 1/4 inch (6.4 mm) from bottom of door to top of threshold unless otherwise indicated.a. Comply with NFPA 80 for fire-rated doors.

2. Bevel non-fire-rated doors 1/8 inch in 2 inches (3-1/2 degrees) at lock and hinge edges.

3. Trim bottom rail only to extent permitted by labeling agency.

D. Factory-Fitted Doors: Align in frames for uniform clearance at each edge.

E. Factory-Finished Doors: Do not trim factory finished doors for width.

3.3 ADJUSTING

A. Operation: Correct any deficiency that prohibits the door from swinging or operating freely. Do not remove hinge screws after initial insertion. Shims used for alignment purposes shall be inserted between hinge and frame. Do not insert shims between hinge and door.1. To prevent stile failure, insure that door closers are properly adjusted and do not limit

the door opening swing. Limit door opening swing only with a properly located stop.

B. Finished Doors: Replace doors that are damaged or that do not comply with requirements. Doors may be repaired or refinished if Work complies with requirements and shows no evidence of repair or refinishing.

END OF SECTION

08210-18

arcat · web viewarcat ... 08210-1

Documents