© this drawing is copyright of mitchell + associates · 2019. 11. 8. · ·relevant standard: bs...
TRANSCRIPT
square pinkerb
dimensions: 50 x 150 x 915
material: concrete
finish: exposed aggregate
colour: silver grey
C7.5P semi-dry concrete bedding
C20P concrete at 25-50mm slump haunch.
play bark safety surfacing
450mm - compacted to 300mm depth
to comply with critical fall heights of specified equipment
to comply with the standards set out in the following:
BS EN 4790:1987 Fire Tested
BS EN 1177 Play Certificate
terram membrane weed barrier
water permeable
Compacted 804 stone at 100-300mm depth
depending on local ground conditions
flexible laying course ~30mm compated
depth to comply with requirements of BS
7533-3 and appropriate to end use of
pavement
flexible jointing to manufacturer's recommendations
sub base to engineer's detail
PC block paving
"Manhattan" by www.tobermore.co.uk
150x600x80mm deep
colours: silver, mid grey and graphite
refer to paving notes
square pinkerb
dimensions: 50 x 150 x 915
material: concrete
finish: exposed aggregate
colour: silver grey
C7.5P semi-dry concrete bedding
C20P concrete at 25-50mm slump haunch.
flexible laying course ~30mm compated
depth to comply with requirements of BS
7533-3 and appropriate to end use of
pavement
2-3mm flexible jointing to manufacturer's recommendations
sub base to engineer's detail
PC sett paving
PC CONCRETE SETT PAVING
"Tegula" by www.tobermore.co.uk
pedestrian and light vehicular overrun
173 x 173 x80mm deep, integral spacer nibs
colours: slate
refer to paving notes
150mm depth insitu concrete pedestrian areas,
250mm depth vehicular/ fire tender access areas
finish: brushed at right angles to long edge
edges: 10mm bullnosed
margin: 100mm float finish to edges of bay
steel reinforcement mesh
to engineers' details
subbase to engineers specification
INSITU CONCRETE KERB
TO ENGINEER'S DETAIL
laid flush
INSITU CONCRETE KERB
TO ENGINEER'S DETAIL
125mm raised
asphalt road surface
to Engineers' details
1600
20
00
1600
20
00
INSITU CONCRETE KERB
TO ENGINEER'S DETAIL
laid flush
1200 1200 12002400
2500
12
00
· PROPOSED PERMEABLE BLOCK PAVING
· Hydropave "Tegula" by www.tobermore.co.uk
· relevant standard: BS EN 1338:2003
· dimensions: 173 x 173 x 80mm, 208 X 173 X 80mm
· colour: bracken
· accessories: integral spacer nib to reduce joint size
disabled logo in white
thermoplastic paint
disabled logo in white
thermoplastic paint
· PROPOSED PERMEABLE BLOCK PAVING
· Hydropave "Tegula" by www.tobermore.co.uk
· relevant standard: BS EN 1338:2003
· dimensions: 173 x 173 x 80mm, 208 X 173 X 80mm
· colour: natural
· accessories: integral spacer nib to reduce joint size
· PROPOSED PERMEABLE BLOCK PAVING
· Hydropave "Tegula" by www.tobermore.co.uk
· relevant standard: BS EN 1338:2003
· dimensions: 173 x 173 x 80mm, 208 X 173 X 80mm
· colour: natural
· accessories: integral spacer nib to reduce joint size
· PROPOSED PERMEABLE BLOCK PAVING
· Hydropave "Tegula" by www.tobermore.co.uk
· relevant standard: BS EN 1338:2003
· dimensions: 173 x 173 x 80mm, 208 X 173 X 80mm
· colour: bracken
· accessories: integral spacer nib to reduce joint size
3 ROWS
PC CONCRETE SETT
PAVING
"Tegula" by
www.tobermore.co.uk
pedestrian and light
vehicular overrun
173 x 173 x80mm deep,
integral spacer nibs
colours: slate
refer to paving notes
150mm depth insitu concrete pedestrian areas,
250mm depth vehicular/ fire tender access areas
finish: brushed at right angles to long edge
edges: 10mm bullnosed
margin: 100mm float finish to edges of bay
asphalt road surface
to Engineers' details
INSITU CONCRETE KERB
TO ENGINEER'S DETAIL
laid flush
INSITU CONCRETE KERB
TO ENGINEER'S DETAIL
PLANTING ON 450mm
DEPTH TOPSOIL
2
5
0
0
2
5
0
0
5
0
0
0
23
00
· PROPOSED PERMEABLE BLOCK PAVING
· Hydropave "Tegula" by www.tobermore.co.uk
· relevant standard: BS EN 1338:2003
· dimensions: 173 x 173 x 80mm, 208 X 173 X 80mm
· colour: bracken
· accessories: integral spacer nib to reduce joint size
3 ROWS
PC CONCRETE SETT
PAVING
"Tegula" by
www.tobermore.co.uk
pedestrian and light
vehicular overrun
173 x 173 x80mm deep,
integral spacer nibs
colours: slate
refer to paving notes
· PROPOSED PERMEABLE BLOCK PAVING
· Hydropave "Tegula" by www.tobermore.co.uk
· relevant standard: BS EN 1338:2003
· dimensions: 173 x 173 x 80mm, 208 X 173 X 80mm
· colour: natural
· accessories: integral spacer nib to reduce joint size
150mm depth insitu concrete pedestrian areas,
250mm depth vehicular/ fire tender access areas
finish: brushed at right angles to long edge
edges: 10mm bullnosed
margin: 100mm float finish to edges of bay
INSITU CONCRETE KERB
TO ENGINEER'S DETAIL
Build Up as per Engineer's Specification
3mm jointing grit
INSITU CONCRETE KERB
TO ENGINEERS' DETAIL
Concrete Haunching to engineer's specification
50mm clean stone
2-6mm aggregate size
geotextile layer
Build Up as per Engineer's Specification
Sub base as per Engineer's Specification
· PROPOSED PERMEABLE BLOCK PAVING
· Hydropave "Tegula" by www.tobermore.co.uk
· relevant standard: BS EN 1338:2003
· dimensions: 173 x 173 x 80mm, 208 X 173 X 80mm
· colour: bracken
· accessories: integral spacer nib to reduce joint size
150mm depth insitu concrete pedestrian areas,
250mm depth vehicular/ fire tender access areas
finish: brushed at right angles to long edge
edges: 10mm bullnosed
margin: 100mm float finish to edges of bay
steel reinforcement mesh
to engineers' details
subbase to engineers specification
30mm deep Bedding Course
cement mortar complying with
section 5.4.4.2 of BS 7533-4
3 ROWS PC CONCRETE SETT PAVING
"Tegula" by www.tobermore.co.uk
pedestrian and light vehicular overrun
173 x 173 x80mm deep, integral spacer nibs
colours: slate
refer to paving notes
450mm depth free
draining topsoil
to planting areas
Road Finish and build up to
Engineer's Specification
INSITU CONCRETE
KERB TO
ENGINEER'S DETAIL
Build Up as per Engineer's Specification
3mm jointing grit
INSITU CONCRETE KERB
TO ENGINEERS' DETAIL
INSITU CONCRETE KERB
TO ENGINEER'S DETAIL
50mm clean stone
2-6mm aggregate size
geotextile layer
Build Up as per Engineer's Specification
Sub base as per Engineer's Specification
· PROPOSED PERMEABLE BLOCK PAVING
· Hydropave "Tegula" by www.tobermore.co.uk
· relevant standard: BS EN 1338:2003
· dimensions: 173 x 173 x 80mm, 208 X 173 X 80mm
· colour: bracken
· accessories: integral spacer nib to reduce joint size
150mm depth insitu concrete pedestrian areas,
250mm depth vehicular/ fire tender access areas
finish: brushed at right angles to long edge
edges: 10mm bullnosed
margin: 100mm float finish to edges of bay
steel reinforcement mesh
to engineers' details
30mm deep Bedding Course
cement mortar complying with
section 5.4.4.2 of BS 7533-4
3 ROWS PC CONCRETE SETT PAVING
"Tegula" by www.tobermore.co.uk
pedestrian and light vehicular overrun
173 x 173 x80mm deep, integral spacer nibs
colours: slate
refer to paving notes
subbase to engineers specification
EXISTING TREE
TO BE RETAINED
PATH TO BE ADJUSTED ON SITE TO
SUIT EXISTING TREES AND MINIMISE IMPACT
existing ground
Note: The use of mechanical equipment or low ground pressure machinery in the
tree root zone must be avoided and hand tools are the only method of excavation
close to the tree root system. Works to be completed under the supervision of the
Arborist for the project. a minimum of 5no. working days notice to be given for
works in proximity of all existing trees.
Do not contaminate the filled cells with site debris, soil or mud.
Geotextile membrane BGT100
50mm deep Bedding Course
cement mortar complying with
section 5.4.4.2 of BS 7533-4
Spiral Steel Spike (at regular intervals - as per manufacturers specification)
Concrete pad foundation
TerramGeocell 200mm deep filled with angular (5-45mm size), without fines clause 804
fixed in place using fixing U pin (1-2m centres) as per manufacturers recommendations
Tensar TriAx TX 160 Geogrid on
geotextile layer BGT100
Extend Terram Geocell 500mm beyond path edge
to either side and marry in levels with topsoil
layer of silica or sharp sand
required beneath to achieve an even surface profile
Textured PC Flag www.tobermore.co.uk
Colour: Buff
Dimensions: 400 x 400 x 40mm
Aluexcel AE 100M Edge Restraint
Supplied By: Kinley Systems or Equal Approved.
Rigid
4mm profile x 100mm height
Top bead: 6mm
EXISTING TREE
TO BE RETAINED
PATH TO BE ADJUSTED ON SITE TO
SUIT EXISTING TREES AND MINIMISE IMPACT
existing ground
Note: The use of mechanical equipment or low ground pressure machinery in the
tree root zone must be avoided and hand tools are the only method of excavation
close to the tree root system. Works to be completed under the supervision of the
Arborist for the project. a minimum of 5no. working days notice to be given for
works in proximity of all existing trees.
Do not contaminate the filled cells with site debris, soil or mud.
Geotextile membrane BGT100
50mm deep Ballylusk compacted gravel 6mm to DUST
Spiral Steel Spike (at regular intervals - as per manufacturers specification)
Concrete pad foundation
Aluexcel AE 50M Edge Restraint
Supplied By: Kinley Systems or Equal Approved.
Rigid
4mm profile x 50mm height
Top bead: 6mm
TerramGeocell 200mm deep filled with angular (5-45mm size), without fines clause 804
fixed in place using fixing U pin (1-2m centres) as per manufacturers recommendations
Tensar TriAx TX 160 Geogrid on
geotextile layer BGT100
Extend Terram Geocell 500mm beyond path edge
to either side and marry in levels with topsoil
layer of silica or sharp sand
required beneath to achieve an even surface profile
EXISTING TREE
TO BE RETAINED
PATH TO BE ADJUSTED ON SITE TO
SUIT EXISTING TREES AND MINIMISE IMPACT
existing ground
Note: The use of mechanical equipment or low ground pressure machinery in the
tree root zone must be avoided and hand tools are the only method of excavation
close to the tree root system. Works to be completed under the supervision of the
Arborist for the project. a minimum of 5no. working days notice to be given for
works in proximity of all existing trees.
Do not contaminate the filled cells with site debris, soil or mud.
Geotextile membrane BGT100
Spiral Steel Spike (at regular intervals - as per manufacturers specification)
Concrete pad foundation
Aluexcel AE 50M Edge Restraint
Supplied By: Kinley Systems or Equal Approved.
Rigid
4mm profile x 50mm height
Top bead: 6mm
TerramGeocell 200mm deep filled with angular (5-45mm size), without fines clause 804
fixed in place using fixing U pin (1-2m centres) as per manufacturers recommendations
Tensar TriAx TX 160 Geogrid on
geotextile layer BGT100
Extend Terram Geocell 500mm beyond path edge
to either side and marry in levels with topsoil
layer of silica or sharp sand
required beneath to achieve an even surface profile
· PROPOSED RESIN BOUND AGGREGATE
· colour: Norwegian Bronze
· intended use: pedestrian and light vehicular
· 6mm natural aggregate, laid to 18mm depth
· refer to product reference schedule for details
BINDER COURSE
35mm depth maximum size AC 10 close graded
asphalt concrete, max 100/ 150 pen to BS EN 13108-1:2006
Tactile Paving Units
Colour Buff
400x400x50mm deep
Precast Concrete Steps
Dimensions: 150x 400 x 3000mm
Colour: White
Handrails
Stainless Steel Posts, FSC approved hardwood rails
Finish: Brushed
Handrail Diameter: 50mm circular section
Shop Drawings to be produced for approval
1 23 1 2
3 1 23
+82.15
+83.50
+82.15
800 400
300
150
Handrails
Material: Stainless Steel posts, FSC approved hardwood Rails
Finish: Brushed
Handrail Diameter: 50mm circular section
Shop drawings to be produced for approval
Precast concrete steps
Dimensions: 150x400x3000mm
Colour: white
PC tactile corduroy pavers
Colour: Buff
Units: 400x400x50mm
50mm deep Bedding Course
Cement moortar complying with section
5.4.4.2 of BS 7533-4
4-6mm joints filled with cement based
mortar class M6 to BS EN 998-2
Sub base to engineer's detail
1100
30mm deep 3:1 mortar bedding
concrete foundations to engineer's specification
Sub base to engineer's detail
400
150
400
150
400
150
+83.50
+83.05
+82.60
1000
1000
1000
precast concrete steps
dimensions: 150 x 400 x 3000mm
colour: white
10mm bullnose to top outer edge
GRP anti-slip decking strip,
50mm width x 4mm depth,
set into 2mm x 54mm recessed
groove with proprietary adhesive
colour: black to top and bottom of flight,
beige to all other steps
PROJECT
JOB NO.
MITCHELL + ASSOCIATES
LANDSCAPE ARCHITECTURE URBAN DESIGN
DRAWING
DATE
SCALE
DRAWING NO.
DRAWN BY
STATUS:
CHECKED
REVISION
REV DESCRIPTION ISSUED BY DATE
Unit 5, Woodpark, The Rise, Glasnevin, Dublin 9, Ireland t: + 353 1 454 5066 e:[email protected]
CLIENT
NOTES:
All dimensions are in millimeters unless otherwise stated and shall be checked and confirmed by the contractor on site. Any
discrepancies shall be immediately reported to the landscape architects. Work to figured dimensions only - Do not scale from
drawing. Do Not Scale. Use Figured Dimensions Only. Not for Construction Purposes unless Specifically Marked.
© THIS DRAWING IS COPYRIGHT OF MITCHELL + ASSOCIATES
TWO OAKS RESIDENTIAL DEVELOPMENT, SCHOLARSTOWN, DUBLIN
ARDSTONE HOMES
LTWO001
HARDWORKS DETAILS
SCH-MLA-ZZ-XX-DR-L-LAN-0006
17.09.2019VERONIKA KUNCLOVA DK
AS SHOWN@ A0 2
D1
AS SHOWN @ A0
DETAIL 1 - PLAY AREA SURFACING AND EDGING
1:25@A0
DETAIL 2 - PC CONCRETE PAVING - PUBLIC AREAS
1:25@A0
DETAIL 3 - PC CONCRETE PAVING - THRESHOLD AREAS
1:25@A0
DETAIL 4A - PERPENDICULAR CAR PARKING BAYS PLAN VIEW
1:50@A0
DETAIL 4B - PERPENDICULAR CAR PARKING BAYS SECTION
1:25@A0
DETAIL 5A - HERRINGBONE CAR PARKING BAYS PLAN VIEW
1:50@A0
DETAIL 5B - HERRINGBONE CAR PARKING BAYS SECTION
1:25@A0
DETAIL 6A - ROOT PROTECTION PAVED AREAS
1:25@A0
DETAIL 6B - ROOT PROTECTION COMPACTED GRAVEL AREAS
1:25@A0
DETAIL 6C - ROOT PROTECTION RESIN BOUND GRAVEL AREAS
1:25@A0
DETAIL 7A- STEPS PLAN VIEW
1:50@A0
DETAIL 7B- STEPS SECTION
1:25@A0
NB: ALL NAMED PRODUCTS
ARE "OR EQUAL AND APPROVED"