SECTION 08 71 00DOOR HARDWARE

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2016 - 2016 ARCAT, Inc. - All rights reserved

1 GENERAL

1.1 SECTION INCLUDES

1.1.1 Door hardware and accessories.

1.2 RELATED SECTIONS

1.2.1 Section 06 10 00 - Rough Carpentry.

1.2.2 Section 08 11 13.16 - Custom Hollow Metal Doors and Frames.

1.2.3 Section 08 11 16 - Aluminum Doors and Frames.

1.2.4 Section 08 14 23.16 - Plastic-Laminate-Faced Wood Doors.

1.2.5 Section 28 13 63 - Access Control Vehicle Identification System.

1.2.6 Section 26 05 00 - Common Work Results for Electrical.

1.3 REFERENCES

1.3.1 American National Standards Institute (ANSI):1.3.1.1 ANSI A117.1 - Accessible and Usable Buildings and Facilities.

1.3.2 Builders Hardware Manufacturing Association (BHMA):1.3.2.1 ANSI/BHMA A115 - Hardware Preparation in Steel Doors or Steel Frame1.3.2.2 ANSI A156 - Performance Standards for Finish Hardware together with BHMA.1.3.2.3 ANSI/BHMA A156.1 - Butts & Hinges.1.3.2.4 ANSI/BHMA A156.2 - Bored and Preassembled Locks and Latches.1.3.2.5 ANSI/BHMA A156.3 - Exit Devices.1.3.2.6 ANSI/BHMA A156.4 - Door Controls - Closers.1.3.2.7 ANSI/BHMA A156.5 - Cylinders and Input Devices for Locks.1.3.2.8 ANSI/BHMA A156.10 - Power Operated Pedestrian Doors.1.3.2.9 ANSI/BHMA A156.12 - Interconnected Locks and Latches.1.3.2.10 ANSI/BHMA A156.13 - Mortise Locks.1.3.2.11 ANSI/BHMA A156.16 - Auxiliary Hardware.1.3.2.12 ANSI/BHMA A156.17 - Self-Closing Hinges.1.3.2.13 ANSI/BHMA A156.18 - Materials and Finishes.1.3.2.14 ANSI/BHMA A156.19 - Power Assist and Low Energy Power Operated Doors.1.3.2.15 ANSI/BHMA A156.23 - Electromagnetic Locks.1.3.2.16 ANSI/BHMA A156.26 - Continuous Hinges.1.3.2.17 ANSI/BHMA A156.31 - Electric Strikes and Frame Mounted Actuators.1.3.2.18 ANSI/BHMA A156.36 - Auxiliary Locks.

08 71 00-1

1.3.3 Door Hardware Institute (DHI):1.3.3.1 DHI / ANSI A115.IG - Installation Guide for Doors and Hardware.1.3.3.2 DHI Sequence and Format for the Hardware Schedule.1.3.3.3 DHI Recommended Locations for Architectural Hardware.

1.3.4 Federal Communications Commission (FCC)

1.3.5 Institute of Electrical and Electronics Engineers (IEEE):1.3.5.1 IEEE 802.15.4 - IEEE Standard for Low-Rate Wireless Personal Area Networks

(WPANs)1.3.5.2 IEEE 802.3 - IEEE Standard for Ethernet

1.3.6 National Fire Protection Association (NFPA):1.3.6.1 NFPA 80 - Fire Doors and Windows.

1.3.7 Underwriters Laboratory, Inc. (UL):1.3.7.1 UL 10B - Standard for Fire Tests of Door Assemblies1.3.7.2 UL 10C - Positive Pressure Fire Test of Door Assemblies.1.3.7.3 UL GYQS - Electrically Controlled Single-point Locks and Latches.1.3.7.4 UL 228 - Standard for Door Closers-Holders, With or Without Integral Smoke

Detectors.1.3.7.5 UL 325 - Standard for Door, Drapery, Gate, Louver, and Window Operators and

Systems.1.3.7.6 UL 1034 - Standard for Burglary-Resistant Electric Locking Mechanisms.

1.3.8 Universal Building Code (UBC):1.3.8.1 UBC 7-2 - Fire Test Standard for Swinging Fire Doors

1.3.9 Wood Door Manufacturer's Association (WDMA):1.3.9.1 WDMA Industry Standard I.S.-1A - Interior Architectural Wood Flush Doors.1.3.9.2 WDMA Industry Standard I.S.-6A - Interior Architectural Stile and Rails Doors.

1.4 ALLOWANCES

1.4.1 Refer to Division 1 for allowances.

1.5 SUBMITTALS

1.5.1 Submit under provisions of Section 01 30 00 - Administrative Requirements including digital submission procedures and quantities of printed copies and physical samples.

1.5.2 Special Submittal Requirements: Combine submittals of this Section with related sections to ensure the design intent of systems and assemblies are understood and can be reviewed together.

1.5.3 Product Data: Provide a complete set of manufacturer's catalog and technical data for each hardware item used, highlighting design, function, fasteners, accessories, and options to facilitate review with each hardware schedule submitted. Include the following:1.5.3.1 Detailed specification of construction and fabrication.1.5.3.2 Manufacturer's installation instructions.1.5.3.3 Submit catalog cuts together with hardware schedule.1.5.3.4 Submit 9001 - Quality Management and 14001 - Environmental Management for

products and materials as specified in Part 2 below.1.5.3.5 Submit manufacturer's standard wiring diagrams for each electric product to be

installed. Coordinate voltage with electrical engineer before submitting.

1.5.4 Shop Drawings and Hardware Schedules:1.5.4.1 Conform to DHI publication "Sequence and Format for Hardware" using

08 71 00-2

Architect's door numbers and hardware set numbers. Submit in vertical format.1.5.4.2 List groups and suffixes in proper sequence.1.5.4.3 Completely describe each door and list architectural door numbers.1.5.4.4 Manufacturers, product names, and catalog numbers.1.5.4.5 Functions, types, and styles.1.5.4.6 Sizes and finishes of each item.1.5.4.7 Mounting heights.1.5.4.8 Explanation of abbreviations and symbols used within schedule.1.5.4.9 Provide elevation drawings for openings with electrical hardware and access

control devices with each hardware schedule. Include illustration of opening, operational description, electrified hardware components, legend, approximate mounting location and size of enclosures, size and quantity of conductors, facility name, date, and door and frame rough-ins required for specific opening.

1.5.4.10 Provide detailed wiring diagrams, specially developed for each opening, indicating electric hardware, security equipment and access control equipment.

1.5.5 Templates: Submit templates and reviewed hardware schedules to door and frame supplier and others as applicable to enable proper and accurate sizing and locations of cutouts and reinforcing.1.5.5.1 Provide two sets of manufacturer's information for mortised and template

hardware.1.5.5.2 Include requirements for internal reinforcements for surface mounted hardware.

1.5.6 Wiring Diagrams to be Provided to Electrical Hardware Installer and to Include:1.5.6.1 Point-to-point diagrams specially developed for each opening that requires

electrical hardware, with hardware delivery to jobsite. Reference elevation drawings submitted with hardware schedule using Architect's opening numbers.

1.5.6.2 Riser diagrams for openings requiring power supplies or access control. Include placement of power supplies, distance of wire runs from power supply, cable quantity and number and gauges of wires.

1.5.6.3 Provide the electrical subcontractor templates, wiring diagrams, and reviewed Hardware Schedules for field coordination and verification of voltages and locations.

1.5.6.4 Coordinate with the project engineers, door hardware and security consultants where required.

1.5.7 Samples:1.5.7.1 One sample of Lever and Rose/Escutcheon design (pair).1.5.7.2 Three samples of metal finishes.1.5.7.3 All samples shall be returned to the hardware supplier, and if approved may be

used on the project.

1.5.8 Keying Schedules:1.5.8.1 Immediately upon receipt of hardware schedule, arrange meeting with Owner,

Architect, hardware supplier and other involved parties. Ensure locksets and locking hardware, are functionally correct and keying and programming complies with project requirements. Determine keying requirements, keying schedule submittal, and update requirements.

1.5.8.2 Submit keying schedules as a result of the keying requirements meeting.1.5.8.3 Unless otherwise agreed, furnish electronic copy of keying, key schematic, and

programming schedules.1.5.8.4 Update and resubmit keying schedules as agreed in the keying requirement

meeting.

1.5.9 Contract Closeout Submittals in Accordance with Division 1:1.5.9.1 Operating and maintenance manuals.1.5.9.2 Final hardware schedules.

08 71 00-3

1.5.9.3 Final, approved, keying schedules.1.5.9.4 Installation templates and manufacturer's instructions.1.5.9.5 As installed wiring diagrams for each piece of hardware connected to low

voltage, 110 volts, and other power.1.5.9.6 Warranties.

1.5.10 Extra Service Materials:1.5.10.1 Deliver to Owner extra materials from same production run as products installed.

Package products with protective covering and identify with descriptive labels.1.5.10.2 Special Tools: Provide special wrenches and tools applicable to each different or

special hardware component, and as required for maintenance and adjustment of hardware, including changing of cylinders.

1.5.10.3 Maintenance Tools: Provide maintenance tools and accessories supplied by hardware component manufacturer.

1.5.10.4 Deliver to Owner remaining finish hardware fasteners and special installation tools upon completion of Project. Comply with Owner's requirements for delivery, storage and protection of extra service materials.

1.5.10.5 Extra Screws and Fasteners: Fifty of each screw and fastener required for general maintenance of hinges, locks, closers, exit devices, and sealing systems.

1.6 QUALITY ASSURANCE

1.6.1 Comply with Division 1 Demonstrating the Following:1.6.1.1 Compliance with regulatory requirements and single source responsibility.1.6.1.2 Distributor's qualifications.1.6.1.3 Supplier qualifications.1.6.1.4 Installer's Qualifications: Firm with 5 years experienced in installation of similar

hardware to that required for this Project, including specific requirements indicated.

1.6.1.5 Regulatory Label Requirements: Provide testing agency label or stamp on hardware for labeled openings.

1.6.1.6 Single Source Responsibility: Except where specified in hardware schedule, furnish products of only one manufacturer for each type of hardware.

1.6.1.7 Wireless locking devices, electric access control, and components must be furnished and installed by manufacturer certified technicians.

1.6.2 Fire Rated Door Openings: Comply with NFPA 80.1.6.2.1 Furnish nationally recognized testing agency label or stamp for labeled

openings.1.6.2.2 Only labeled locks or latches or fire exit hardware can be used on fire rated

openings.1.6.2.3 Do not modify tested or labeled doors, frames, or hardware in the field.

1.6.3 Pre-Installation Meeting: Convene at the project site a minimum of two weeks prior to starting work of this section.1.6.3.1 Prior to installation of hardware, arrange for hardware supplier and/or

manufacturer's representatives of locksets, door closers, and exit devices to hold a jobsite meeting to instruct the installing personnel on the proper installation of their products.

1.6.3.2 Send a letter to the Architect and Owner, indicating when this meeting was held, and who was in attendance.

1.6.4 Mock-Up: Provide a mock-up for evaluation of preparation and installation techniques and application workmanship. Install mock-up in areas designated by Architect.1.6.4.1 Do not proceed with remaining work until mock-up is approved by Architect.1.6.4.2 Rebuild mock-up area as required to produce acceptable work.

08 71 00-4

1.6.4.3 Accepted mock-up may remain as part of the finished work and set the standard for remaining work.

1.7 DELIVERY, STORAGE, AND HANDLING

1.7.1 Deliver products in original unopened packaging with legible manufacturer's identification marked to correspond with approved hardware schedule with Architect's door numbers and hardware sets.1.7.1.1 Jointly check in hardware with general contractor, hardware supplier, and

hardware installer, upon delivery to jobsite, against approved hardware schedule with hardware supplier. Record shortage or damage and replace or repair as necessary.

1.7.1.2 Deliver hardware to be installed during fabrication of doors and frames, to manufacturer upon request.

1.7.2 Mark hardware to correspond with reviewed hardware schedule. Mark locksets, exit devices, cylinders, auxiliary hardware and key switches with keyset symbol.

1.7.3 Package hardware to prevent damage during transit and storage. Replace any wet or damaged packaging with new.

1.7.4 Storage and Protection: Comply with manufacturer's recommendations.1.7.4.1 Store hardware in a secure, dry, temperature controlled room on shelving to

protect against loss, theft and damage.1.7.4.2 Store items that do not fit on shelving on pallets, off the floor.

1.8 PROJECT CONDITIONS

1.8.1 Coordinate hardware with other work. Furnish hardware items of proper design for use on doors and frames of the thickness, profile, swing, security and similar requirements indicated, as necessary for the proper installation and function, regardless of omissions or conflicts in the information on the Contract Documents.

1.8.2 Review shop drawings for doors and entrances to confirm that adequate provisions will be made for the proper installation of hardware.

1.8.3 Review Project for extent of finish hardware required to complete the Work. Where there is a conflict between these specifications and the existing hardware, notify the Architect in writing and furnish hardware in compliance with the specification unless otherwise directed in writing by the Architect.

1.8.4 Intent of Hardware Groups:1.8.4.1 Where hardware items required for completion of the Work are not definitively or

correctly specified, provide a written statement to Architect, prior to date specified in Division 01 for receipt of bids, or for clarification by addendum.

1.8.4.2 If discrepancies are observed after specified dates, furnish such items in the type and quality established by this specification, and appropriate to the service intended at no additional cost to the Owner.

1.8.5 Field modification and preparation of existing doors and frames for new hardware being installed. Provide fillers, accessories, reinforcements, and fasteners for mounting new hardware and to cover existing door and frame preparations.

1.8.6 Instruct Owner's personnel in operation and maintenance of hardware units.

1.9 WARRANTY

1.9.1 Refer to Conditions of the Contract for extended or limited warranties. Furnish warranties in

08 71 00-5

accordance with Division 1. Warrant against defects in material and workmanship, from date of substantial completion unless otherwise indicated. Provide the following manufacturers warranties at minimum:1.9.1.1 Closers: Thirty Years.1.9.1.2 Exit Devices: Three Years.1.9.1.3 Mortise Locksets: Lifetime.1.9.1.4 Cylindrical Locksets and Cylinders: Three years.1.9.1.5 Other Hardware: Two years.

1.10 MAINTENANCE

1.10.1 Maintenance Service: Submit maintenance service agreement for Owner's consideration for installed electronic products.

2 PRODUCTS

2.1 MANUFACTURERS

2.1.1 Acceptable Manufacturer: Stanley Security Solutions, which is located at: 6161 E. 75th St.; Indianapolis, IN 46250; Tel: 317 849 2250; Fax: 317-806-3276; Email:request info (ngugliotti@stanleyworks.com); Web:www.stanleysecuritysolutions.com

2.1.2 The following manufacturers are approved subject to compliance with requirements of the Contract Documents. Approval of manufacturers other than those listed to be in accordance with Division 1.2.1.2.1 Hinges: Stanley.2.1.2.2 Continuous Hinges: Stanley.2.1.2.3 Spring Hinges: Stanley.2.1.2.4 Flush Bolts: Trimco, or ABH, Burns.2.1.2.5 Locksets: Best.2.1.2.6 Exit Devices: Precision.2.1.2.7 Surface Closers (cast iron): Stanley.2.1.2.8 Surface Closers (aluminum): Stanley.2.1.2.9 Low Energy Operators: Stanley.2.1.2.10 Floor and Wall Stops: Trimco, or ABH, Burns.2.1.2.11 Overhead Stops: ABH, or Rixson, Glynn Johnson.2.1.2.12 Door Protection: Trimco or ABH, Burns.2.1.2.13 Electric Strikes: Stanley or Security Door Controls.2.1.2.14 Thresholds: National Guard or Reese, DHSI.2.1.2.15 Gasketing: National Guard or Reese, DHSI.2.1.2.16 Magnetic Door Holders: ABH or Security Door Controls, LCN.2.1.2.17 Silencers: Trimco or Burns, Hiawatha.2.1.2.18 Coordinator and Brackets: Trimco or ABH, Burns.

2.1.3 Submit Requests for Substitution in Accordance with Section 01 60 00 - Product Requirements:2.1.3.1 Provide catalog data with product information highlighted or bubbled to facilitate

review. Product must meet or exceed level or design intended or function established by specified products.

2.2 SCREWS AND FASTENERS

2.2.1 Screws and Fasteners:2.2.1.1 Provide manufacturer's recommended fasteners of proper type, material and

finish.2.2.1.2 Provide self-tapping screws for sweeps and stop applied weather stripping.2.2.1.3 Utilize through-bolts for the attachment of door closers and exit devices on non-

08 71 00-6

reinforced doors only. Finish: match door face.2.2.1.4 Exposed Screws: Phillips-head except where tamper proof fasteners are

required.

2.3 HINGES

2.3.1 Five Knuckle, Full Mortise, Bearing Hinges:2.3.1.1 BHMA certified complying with applicable ANSI standards for type, size, function

and finish. UL 10C listed for fire rated doors.2.3.1.2 Sufficient size to allow 180-degree swing of door.2.3.1.3 Heavy Weight Hinges: On heavy doors and doors expected to have high

frequency use. Template screw hole locations.2.3.1.4 Bearings: Fully hardened. Bearing shell to be consistent shape with barrel.2.3.1.5 Minimum of 2 permanently lubricated non-detachable bearings on standard

weight hinge and 4 permanently lubricated bearing on heavy weight hinges.2.3.1.6 Bearing assemblies to be installed after plating.2.3.1.7 Equip with easily seated, non-rising pins.2.3.1.8 Non-removable pins (NRP) at exterior doors and reverse bevel doors with

locking hardware. Non Removable Pin screws to be slotted stainless steel screws.

2.3.1.9 Hinge pins: Fully plated and polished, front, back and barrel.2.3.1.10 Refer to manufacturer's literature and hardware schedule for base metals and

finishes.

2.3.2 Concealed Bearing Hinges:2.3.2.1 BHMA certified complying with ANSI/BHMA A156.26, Grade 1.2.3.2.2 Configuration appropriate for type, inset, and thickness of door. Coordinate with

door manufacturer.2.3.2.3 Match appearance of plain bearing hinges for uniform appearance throughout

the project.2.3.2.4 Maintenance free.2.3.2.5 Limited lifetime warranty.

2.3.3 Geared Continuous Hinges:2.3.3.1 BHMA certified complying with ANSI/BHMA A156.26, Grade 1.2.3.3.2 Configuration appropriate for type, inset, and thickness of door. Coordinate with

door manufacturer.2.3.3.3 Non-handed, and sufficient size to permit door to swing 180 degrees.2.3.3.4 Meet UL fire label listing requirements at UL rated openings. Include fire pins as

required by manufacturer. Provide UL 10C listed for 3 hour fire rating.2.3.3.5 Anti-spinning through fastener.2.3.3.6 Limited lifetime warranty.

2.3.4 Pin and Barrel Continuous Hinges:2.3.4.1 BHMA certified complying with ANSI/BHMA A156.26, grade 1. fabricated from

14 gauge material.2.3.4.2 UL and ULC listed for fire-rated 4 x 8 foot (1219 x 2438 mm) single doors and 8

x 8 foot (2438 x 2438 mm) door pairs, up to 3 hours.2.3.4.3 Slim Barrel Design: Twin nylon self-lubricating bearings located between

knuckles except top and bottom. Two stainless steel bearings top and bottom, to prevent sagging if nylon bearings degrade during a fire.

2.3.4.4 Limited lifetime warranty.

2.3.5 Electrified Hinges and Hinge Functions:2.3.5.1 Sufficient number of concealed wires with quick connect plug in connectors to

accommodate electrical function of hardware.2.3.5.2 Supply junction boxes and mortar shields.

08 71 00-7

2.3.5.3 Provide wire quantities and sizes required for electric hardware to be served.2.3.5.4 Monitoring: Concealed electrical monitoring switches.2.3.5.5 Power Transfer and Monitoring: Concealed PTFE-jacketed wires, secured at

each leaf, continuous through hinge knuckle, with concealed electrical monitoring switch.

2.3.6 Concealed Electric and Concealed Bearing Hinges:2.3.6.1 Conduct current regardless of door position.2.3.6.2 No exposed electric parts.

2.3.7 Quick Connect Power Transfer: Power transfer device shall be a steel housing and flexible tube. Secure and inconspicuous channel is to bring power from the frame to the door.2.3.7.1 Precision EPT-12C Tube shall contain 12 Wire bundle with Stanley Quick

Connect Connectors one 4 wire connector consisting of two 18AWG wires and 2 24AWG wires and one 8 wire connector with 8 24AWG wires.

2.3.8 Spring Hinges: Closes doors automatically.2.3.8.1 Square corner type complying with ANSI/BHMA A156.17 with ratchet adjustment

to eliminate need for adjustment locking pin.2.3.8.2 Meet NFPA 80 for 3 hour rated doors with minimum 2 spring hinges per door

required.2.3.8.3 Coordinate with door hardware sets.2.3.8.4 Do not duplicate door closers.

2.4 FLUSH BOLTS

2.4.1 Provide the Following:2.4.1.1 Hollow Metal Label Doors: Automatic bolts, Certified ANSI/BHMA 156.3 Type 25.2.4.1.2 Wood Label Doors: Automatic bolts, Certified ANSI/BHMA 156.3 Type 27.2.4.1.3 Where Permitted: Manual flush bolts, Certified ANSI/BHMA 156.16.2.4.1.4 Doors Without Thresholds: Dust Proof Strikes certified ANSI/BHMA 156.16.2.4.1.5 Inactive Leaf of Locked Door Pairs: Two manual flushbolts.2.4.1.6 Fire Rated Doors: One pair of automatic flushbolts.2.4.1.7 Occupied Rooms for Egress: One pair of automatic flushbolts.

2.4.2 Acceptable Manufacturers and Types:2.4.2.1 Manual Metal Doors: Trimco: 3917, Burns: 590.2.4.2.2 Manual Wood Doors: Trimco: 3913, Burns: 591.2.4.2.3 Automatic Metal Doors: Trimco: 3810, Burns: 7842.2.4.2.4 Automatic Wood Doors: Trimco: 3815, Burns: 7942.

2.5 LOCKS AND LATCHES

2.5.1 Mortise Type Locks and Latches:2.5.1.1 BHMA certified complying with ANSI/BHMA A156.13, Series 1000, operational

grade 1, extra-heavy duty, security grade 1 (with high security cylinder) security grade 2 (with removable core cylinder). UL 10C listed.

2.5.1.2 Furnish UL or recognized independent laboratory certified mechanical operational testing to 4 million cycles minimum.

2.5.1.3 Comply with 9001 - Quality Management and 14001 - Environmental Management standards.

2.5.1.4 Comply with ANSI/BHMA A115.1 for door preparation.2.5.1.5 Functions and design as indicated in the hardware schedules.2.5.1.6 Latchbolts: Solid, one-piece, 3/4 inch (19 mm) throw, anti-friction made of self-

lubricating stainless steel.2.5.1.7 Deadbolts: 1 inch (25 mm) throw bolt made of hardened stainless steel.2.5.1.8 Latchbolts and Deadbolts: Extend into the case a minimum of 3/8 inch (9.5mm)

08 71 00-8

when fully extended.2.5.1.9 Auxiliary Deadlatch: One-piece stainless steel, permanently lubricated.2.5.1.10 Curved strike lip to protect door trim.2.5.1.11 Lever Handles: Forged or cast brass, bronze or stainless steel construction and

conform to ANSI A117.1. Levers that contain a hollow cavity are not acceptable.2.5.1.12 Levers to operate a roller bearing spindle hub mechanism.2.5.1.13 Levers to have independent spring mechanism controlling it.2.5.1.14 Locks to have self-aligning, thru-bolted trim.2.5.1.15 Mortise cylinders of lock to have concealed internal setscrew for securing the

cylinder to the lockset. The internal setscrew will be accessible only by removing the core, with the control key, from the cylinder body.

2.5.1.16 Spindles designed to prevent forced entry from attacking of lever.2.5.1.17 7-pin removable and interchangeable core cylinders.2.5.1.18 Core face must be the same finish as the lockset.

2.5.2 Mortise Deadbolts:2.5.2.1 BHMA certified complying with ANSI/BHMA A156.5, operational grade 1.2.5.2.2 Comply with 9001 - Quality Management and 14001 - Environmental

Management standards.2.5.2.3 Locksets and cores to be from same manufacturer to maintain complete

warranty.2.5.2.4 Backset: Fits 2-3/4 inch (70 mm).2.5.2.5 Deadbolt Function: 1 inch (25 mm) throw bolt made of hardened stainless steel.2.5.2.6 7-pin core cylinders.

2.5.3 Heavy Duty Cylindrical Locks Grade 1:2.5.3.1 BHMA certified complying with ANSI/BHMA A156.2, Series 4000 operational

grade 1.2.5.3.2 Lock functions and design as specified in hardware schedules.2.5.3.3 Latchbolt with appropriate throw for fire rated doors and pairs of doors in

accordance with manufacturers listing.2.5.3.4 Backset: Fits 2-3/4 inch (70 mm).2.5.3.5 Strike Single Door: ANSI 4 7/8 inch (124 mm) with proper lip length to clear trim.2.5.3.6 Strike Pair of Doors: Flat lip strike sized to fit flush with face of door.2.5.3.7 Furnish wrought strike box.

2.5.4 Heavy Duty Cylindrical Locks Grade 1:2.5.4.1 BHMA certified complying with ANSI/BHMA A156.2, Series 4000 operational

grade 1.2.5.4.2 Lock functions and design as specified in hardware schedules.2.5.4.3 Latchbolt with appropriate throw for fire rated doors and pairs of doors in

accordance with manufacturers listing.2.5.4.4 Backset: Fits 2-3/4 inch (70 mm).2.5.4.5 Strike Single Door: ANSI 4 7/8 inch (124 mm) with proper lip length to clear trim.2.5.4.6 Strike Pair of Doors: Flat lip strike sized to fit flush with face of door.2.5.4.7 Furnish wrought strike box.

2.5.5 Medium Duty Cylindrical Grade 2 Type Locks and Latchsets:2.5.5.1 BHMA certified complying with ANSI/BHMA A156.2, Series 4000 operational

grade 2.2.5.5.2 Fit modified ANSI/BHMA A115.3 door preparation.2.5.5.3 Functions and design as indicated in hardware schedules.2.5.5.4 Locksets and cores to be from same manufacturer to maintain complete

warranty.2.5.5.5 Backset: Fits 2-3/4 inch (70 mm) or 2-3/8 (60 mm).2.5.5.6 Latchbolt Throw: 1/2 inch (13 mm).

08 71 00-9

2.5.5.7 7-pin core cylinders.

2.5.6 Medium Duty Cylindrical Type Locks and Latchsets:2.5.6.1 BHMA certified complying with ANSI/BHMA A156.2 Series Grade 2.2.5.6.2 ANSI A117.1 accessibility code (ADA Compliant).2.5.6.3 UL/ULC listed (3 hours) for "A" label single door application.2.5.6.4 UL 10C/UBC 7-2 (1997) positive pressure rated. UL10B pressure rated.2.5.6.5 Fit modified ANSI/BHMA A115.2 door preparation.2.5.6.6 Functions and design as indicated in hardware schedules.2.5.6.7 Backset: Fits 2 3/4 inch (70 mm).2.5.6.8 Latch Faceplate: 1-1/8 x 2 1/4 inches (29 x 57 mm).2.5.6.9 ANSI Strike: 1-1/4 x 4 7/8 inches (32 x 124 mm).2.5.6.10 Latchbolt Throw: 1/2 inch (13 mm) for single doors.2.5.6.11 Pairs of Fire Doors: 3/4 inch (19 mm) throw or as specified in hardware set.

2.5.7 Cylindrical Deadbolts:2.5.7.1 BHMA certified complying with ANSI/BHMA A115.3 door preparation.2.5.7.2 Comply with 9001 - Quality Management and 14001 - Environmental

Management.2.5.7.3 Locksets and cores to be from same manufacturer to maintain complete

warranty.2.5.7.4 Backset: Fits 2-3/4 inch (70 mm) or 2 3/8 inch (60 mm).2.5.7.5 Throw: 1 inch (25 mm).2.5.7.6 7-pin core cylinders.

2.5.8 Medium Duty Tubular Locks and Latchsets:2.5.8.1 BHMA certified complying with ANSI/BHMA A156.2, Grade 2.2.5.8.2 UL/UL 10C UBC 7-2 positive pressure rated.2.5.8.3 ANSI A117.1 accessibility code (ADA Compliant).2.5.8.4 Functions and design as indicated in hardware schedules.2.5.8.5 Door Preparation: Cross bore 2-1/8 inch (54 mm), edge bore 1 inch (25 mm),

latch face 1 x 2-1/4 inches (25 x 57 mm).2.5.8.6 Universal Backset: Fits 2-3/4 inch (70 mm) or 2-3/8 inch (60 mm).2.5.8.7 Latchbolt Throw: 1/2 inch (13 mm) for single doors.

2.5.9 Interconnected K2 Type Locks and Latchsets:2.5.9.1 BHMA certified complying with ANSI/BHMA A156.12 Grade 2.2.5.9.2 UL/ULC listed (3-hours) for "A" label single doors.2.5.9.3 UL 10C / UBC 7-2 positive pressure rated.2.5.9.4 ADA thumb turn to ANSI A117.1.2.5.9.5 Functions and design as indicated in hardware schedules.2.5.9.6 Door Preparation: Cross bore 2-1/8 inch (54 mm) edge bore 1 inch (25 mm), 4

inches (102 mm) center to center only.2.5.9.7 Backset: Fits 2-3/4 inch (70 mm).2.5.9.8 Latchbolt Throw: 1/2 inch (13 mm).2.5.9.9 Cylinder SmartKey or 5-6-pin tumbler.

2.5.10 Lock Cylinders:2.5.10.1 Provide the necessary cylinder housings, collars, rings & springs as

recommended by the manufacturer for proper installation.2.5.10.2 Provide the proper cylinder cams or tail piece as required to operate locksets

and other keyed hardware items listed in the hardware sets.2.5.10.3 Coordinate and provide as required for related sections.

2.5.11 Keys and Keying:2.5.11.1 Acceptable Manufacturer and Product: Best CORMAX Patented 7-pin, cylinders;

removable and interchangeable cores.

08 71 00-10

2.5.11.2 Provide keyed brass construction cores and keys during the construction period. Construction control and operating keys and cores will not be part of the Owner's permanent keying system or furnished in the same keyway (or key section) as the Owner's permanent keying system. Permanent cores and keys prepared according to the accepted keying schedule will be furnished to the Owner.

2.5.11.3 Permanent Keys and Cores: Stamped with the applicable key mark for identification. These visual key control marks or codes will not include the actual key cuts. Permanent keys to be stamped "Do Not Duplicate."

2.5.11.4 Furnish keys in quantities indicated on Drawings or Schedules.2.5.11.5 Furnish keys in quantities recommended by manufacturer.2.5.11.6 The Owner or the Owner's agent will install permanent cores and return the

construction cores to the hardware supplier. Construction cores and keys remain the property of the hardware supplier.

2.5.11.7 Unless otherwise required, transmit grand masterkeys, masterkeys and other security keys to Owner by registered mail, return receipt requested.

2.6 WIRELESS LOCKING DEVICES AND COMPONENTS

2.6.1 Electronic Operated IDH Max includes door position indicator, and request to exit switch (RQE). The 1300 option eliminates the need for a reader interface module (RIM) and incorporates 3 modules into a single electronic board inside IDH Max escutcheon trim.2.6.1.1 Electrical Cylindrical Locks: Maximum current draw to be 10.2 to 13.2 VDC at

850 milliamps for 50 milliseconds.2.6.1.2 Electric Mortise Type Locks and Latches: Maximum current draw to be 10.2 to

13.2 VDC at 1.1 Amp for 50 milliseconds.2.6.1.3 Card readers.

2.6.2 BEST Cylindrical Type Locks and Latchsets using Stanley Wi-Q Technology:2.6.2.1 BHMA certified complying with ANSI/BHMA A156.2, Series 4000, operational

grade 1, extra-heavy duty. UL10C listed.2.6.2.2 Fit modified ANSI/BHMA A115.2 door preparation.2.6.2.3 Functions and design as indicated in hardware schedules.2.6.2.4 Electric operation as defined and required.2.6.2.5 Locksets to have anti-rotational studs that are thru-bolted.2.6.2.6 Levers to have independent spring mechanism controlling them.2.6.2.7 Backset: Fit 2-3/4 inch (70 mm).2.6.2.8 Latchbolt Throw: 9/16 inch (14 mm).2.6.2.9 7-pin removable and interchangeable core cylinders.2.6.2.10 Core face must be the same finish as the lockset.2.6.2.11 Request to exit switch (RQE) and door position switch (DS).2.6.2.12 Provide minimum of 10 cards in format type as specified per lock.

2.6.3 BEST Mortise Type Locks using Stanley Wi-Q Technology:2.6.3.1 BHMA certified in compliance with ANSI/BHMA A156.13, series 1000,

operational grade 1, extra-heavy duty, security grade 2. UL 10C listed.2.6.3.2 Fit ANSI/BHMA A115.1 door preparation. Functions and design as indicated.2.6.3.3 Functions and design as indicated in hardware schedules.2.6.3.4 Electric operation as defined and required.2.6.3.5 Latchbolts: Solid, one-piece, 3/4 inch (19 mm) throw, anti-friction made of self-

lubricating stainless steel.2.6.3.6 Deadbolts: 1 inch (25 mm) throw bolt made of hardened stainless steel.2.6.3.7 Auxiliary Deadlatches: One-piece stainless steel, permanently lubricated.2.6.3.8 Curved strike lip to protect door trim.2.6.3.9 Lever Handles: Forged or cast brass, bronze or stainless steel construction and

conform to ANSI A117.1. Levers that contain a hollow cavity are not acceptable.2.6.3.10 Levers to operate a roller bearing spindle hub mechanism.

08 71 00-11

2.6.3.11 Levers to have independent spring mechanism controlling it.2.6.3.12 Locks to have self-aligning, thru-bolted trim.2.6.3.13 Mortise cylinders of locks to have a concealed internal setscrew for securing the

cylinder to the lockset. The internal setscrew will be accessible only by removing the core, with the control key, from the cylinder body.

2.6.3.14 Spindles to be designed to prevent forced entry from attacking of lever.2.6.3.15 Locksets provided with 7-pin removable and interchangeable core cylinders.2.6.3.16 Core faces must be the same finish as the lockset.2.6.3.17 Request to exit switch (RQE) switch and door position switch (DS).2.6.3.18 Minimum of 10 cards in format type as specified per lock.

2.6.4 BEST EX Exit Devices using Stanley Wi-Q Technology:2.6.4.1 BHMA certified complying with ANSI/BHMA 156.3, Grade 1.2.6.4.2 UL Listed "A" Label for GYQS.2.6.4.3 Listed for UL 10C. UL listed for accident hazard.2.6.4.4 Deadlocking latchbolt.2.6.4.5 Non-fire rated exit devices to have cylinder dogging.2.6.4.6 Exposed components to be of architectural metals and finishes as selected.2.6.4.7 Lever design: Match lockset lever design.2.6.4.8 Strikes as required by application.2.6.4.9 Request to exit switch, door position switch and trim.2.6.4.10 Primary Power: Battery pack.2.6.4.11 User Indicators: Visible and audible.2.6.4.12 Shock Resistance: 2000 G's RMS.2.6.4.13 Operating Temperature Range: Minus 22 to 140 degrees F (minus 30 to 60

degrees C).2.6.4.14 Weather-resistant for exterior applications.2.6.4.15 Wiring diagrams and elevation drawings of exit devices and locksets.

2.7 WIRELESS ACCESS MANAGEMENT SYSTEM

2.7.1 Basis of Design: Stanley Wi-Q Technology Wireless Access Management System.

2.7.2 Readers / Locks:2.7.2.1 Integrated smart locking device with its own database as specified below.2.7.2.2 Installed within existing ANSI/BHMA A115.2 door preparation cut out. No need to

rout out the door to drive additional power through any electric transfer hinge. Requirements will be met within the reader / lock itself.

2.7.2.3 Wireless Reader to use a AA battery pack.2.7.2.4 No AC power required at the door.2.7.2.5 Cylindrical Lock Applications: Wireless readers provide support for an integral

request to exit switch (RQE) and door switch monitor (DS).2.7.2.6 Mortise Lock Applications: Wireless readers to provide support for integral

request to exit switch (RQE), door switch monitor (DS), door latch position switch (LS), and key over-ride sensor (KOS).

2.7.2.7 Exit Device Applications: Support for an integral request to exit switch (RQE), door switch monitor (DS), and door latch position switch (LS).

2.7.3 Reader / Lock Databases:2.7.3.1 Support 2,000 unique ID's in standard configurations, expandable to 65,000

unique ID's. Expansion to not require a field upgrade at reader. A software key will be downloaded from the host to increase the database size and support up to ____ cardholders.

2.7.3.2 Support 28,000 transactions in the event the lock cannot communicate to the portal gateway. In the unlikely event the reader / lock is offline from the host, it will continue to operate, storing and recording accesses until it is re-connected and back online to the host. Data will be downloaded to the host upon

08 71 00-12

connection.2.7.3.3 144 user-defined time zones with 6 time intervals per time code.2.7.3.4 32 types of unique user defined holidays to be supported. Each holiday to be

capable of supporting a different time code.2.7.3.5 A unique set of access privileges available for each cardholder per reader / lock.2.7.3.6 Memory allocation to be dynamic maximizing the size of the available memory to

meet requirements for either ID's or transaction storage.2.7.3.7 Time zones will cross midnight such that a shift beginning at 10:00 pm and

ending at 9:00 am the next morning, will be considered as a single time zone.2.7.3.8 Support an auto-enroll mode where users may select a reader to be used to

enroll a large group of cardholders by either bulk loading card ID numbers between a specific range or by presenting a card to a reader that then reads the card data and enrolls the card into the database.

2.7.4 Reader / Lock Operation Modes:2.7.4.1 Support access control for a single door with reader and egress on the same

door.2.7.4.2 Monitor door position status to detect door open and door locked and secure. No

separate contact will be required to be mounted to the frame of the door and wired back to a separate contact monitoring device. Alarm monitoring at the door / portal will be monitored by the reader / lock and not require additional controller.

2.7.4.3 Report any access transaction with the date and time of the event. Time format to be hours, minutes, and seconds (hh:mm:ss).

2.7.4.4 Support up to 7 unique shunt times for specific groups of individuals and meet ADA compatibility requirements for extended shunt times for any single or groups of physically impaired cardholders.

2.7.4.5 Support a request to exit (RQE) status that will be reported separately as a separate auditable transaction. In the event that an attempt to exit is made, but the door / portal remains closed (secure), then the transaction will not be recorded as a valid Request to exit (RQE) and will time out after the shunt time has expired.

2.7.4.6 Support and transmit a signal if the power to the reader / lock drops below 10 percent.

2.7.4.7 Support different operation modes based on time zones. Thus a reader may be in a card only mode in the daytime, but require card plus PIN after hours. Dully user programmable from the host.

2.7.4.8 Able to operate in a fully standalone mode or as a distributed fully intelligent reader/ lock holding the transactions until they are polled.

2.7.4.9 Communicate via spread spectrum radio transmission at 2.4 GHZ.2.7.4.10 Use a standard, AES 128-bit encryption to the nearest non-dedicated portal

gateway. Portal gateways to provide redundant communications capability so that a wireless reader can report to another portal gateway if primary reporting path is lost.

2.7.4.11 Report multiple incorrect PIN attempts (greater than 3) as an alarm attempt.2.7.4.12 Able to detect the presence of a proximity card, such that the cardholder will not

be required to orient their card in a specific manner to wake up the reader.2.7.4.13 Read / response time to an access request not exceed 250 Milliseconds.2.7.4.14 Each reader lock to have its own unique MAC address.

2.7.5 Wireless Access Controllers: Include the following:2.7.5.1 Support access control for a single door with reader and egress on the same

door.2.7.5.2 Capable of interfacing with a token reader utilizing a standard Wiegand protocol

to unlock various electrified locking hardware such as electric strikes, exit device trim, electro-magnetic locks and other low voltage applications. Will also serve

08 71 00-13

as a retrofit kit to replace an existing wired infrastructure with a local wireless reader PCB that has the ability to slave to a wired reader and local peripherals at the door.

2.7.5.3 Support an existing request to exit switch (RQE), door switch monitor (DS), and door latch position switch (LS).

2.7.5.4 Support a locally powered locking device rated up to 4 Amps at 12/24 V DC.2.7.5.5 Auxiliary relay output will be available to drive other door related outputs. This

relay to be rated at 2 Amps 12/24 V DC.2.7.5.6 Have the same feature set of software capabilities as the standard wireless

reader for up to 65,000 ID's, 144 Time Zones, variable shunt times for different staff groups, and ADA compliance.

2.7.5.7 Support most Wiegand card formats from 16 to 128 bits and be able to serve as a log on or enrollment reader where an individual or group of individuals may "badge" into the system and the system will identify their card data so the card can be auto-enrolled.

2.7.5.8 Provide wireless communications back to a Portal Gateway such that no separate controllers will be required for decision making. Door related decisions will be made at the wireless access controller local to the readers it serves.

2.7.5.9 Terminations to the wireless access controller to be through plug in wired block terminals - no special tools will be required to install the unit(s).

2.7.5.10 The reader will be able to operate in different modes such that it is able to serve as a smart I/O module supporting I/O functions either as ancillary services to its primary role as an access control device or as its sole role.

2.7.5.11 With half wave dipole antennas and a ceiling mount omni directional antenna with 20 feet of cable and required connectors

2.7.6 Portal Gateways: Operate in a non-dedicated mode such that any reader / lock shall be able to report to and through any portal gateway. The portal gateways shall accept data from any of the addressed readers and transmit bi-directional encrypted data to the host for archiving and data management. Each portal gateway shall have the following capabilities:2.7.6.1 Base System Configuration: Support a minimum of 64 reader / locks in its

antenna range and via system options.2.7.6.2 Its own unique MAC address such that, on boot up, the host will find and identify

those portal gateways that belong to the system.2.7.6.3 Encrypted data using 128-bit AES encryption. Send and receive data via spread

spectrum RF transmission to and from the host.2.7.6.4 Option stand-by power supply support.2.7.6.5 Support two transmission paths to the host. The user may elect to use standard

ethernet cabling between the portal gateway and the host using a cross over cable. standard ethernet using local hubs and routers.

2.7.6.6 Its own static IP address.2.7.6.7 Support secure socket communications between the host(s) / server and any

associated portal gateway. This shall be user selectable.

2.7.7 Hosts / Web Services: The Host's software will run on industry standard, commercially available, computer platforms offered from multiple PC vendors. There shall be no constraints on the PC platform if it meets the minimum specifications listed. The host, Stanley Wi-Q software and B.A.S.I.S., shall use Microsoft Windows 2003 Server as the operating system with a SQL database and run on a standard, off the shelf computer platform with the following minimum operating specifications:2.7.7.1 Help screen support for major functions.2.7.7.2 Support multi byte character sets such that translations into non -standard ASCII

characters above 128 are fully supported.2.7.7.3 Support web services such that non-administrative tasks shall be able to be

serviced through a standard web browser.2.7.7.4 Approved Operating Systems:

08 71 00-14

2.7.7.4.1 Windows 7 Professional, Ultimate and Enterprise SP1 (32 & 64 Bit).2.7.7.4.2 Windows 8.1 Professional and Enterprise (32 & 64 Bit).2.7.7.4.3 Windows 10 Professional (See FAQ for required corrective actions).2.7.7.4.4 Windows Server 2008 R2 Standard and Enterprise SP1 (64 Bit).2.7.7.4.5 Windows Server 2012 Standard and R2 Standard (64 Bit).

2.7.7.5 Approved Database Versions:2.7.7.5.1 SQL 2008 Express (32 & 64 Bit).2.7.7.5.2 SQL 2008 R1 SP3 (32 & 64 Bit).2.7.7.5.3 SQL 2008 R2 SP2 (32 & 64 Bit).2.7.7.5.4 SQL 2012 Express (32 & 64 Bit).2.7.7.5.5 SQL 2012 R1 SP1 (32 & 64 Bit).2.7.7.5.6 SQL 2014 (32 & 64 Bit).

2.7.7.6 Required Hardware:2.7.7.6.1 Processor: Pentium Quad Core 2.6 GHz or faster.2.7.7.6.2 Memory: Minimum 4 GB.2.7.7.6.3 Hard Drive: Minimum 80 GB for storage and data management.2.7.7.6.4 DVD-ROM2.7.7.6.5 USB-Port or wireless hub with minimum of: 10/100BaseT.2.7.7.6.6 Display: 1024x768, Color.

2.8 ELECTRONIC LOCK SYSTEMS

2.8.1 Electronic Lock System Description: At electronic access openings, furnish and install system equal to Best Access System. B.A.S.I.S V as scheduled in the hardware sets.2.8.1.1 Complete programming, data storage and software.2.8.1.2 Connector package, encoder and cable, as necessary, to interface with minimum

recommended computer system.2.8.1.3 Lock units as detailed in hardware schedules.2.8.1.4 Include batteries, cards, portable programmer for locks units, special tools,

operating manuals, and on-site training of staff.

2.8.2 B.A.S.I.S Electronic Lock and Trims: At electronic access openings, furnish and install system equal to Best Access System. B.A.S.I.S V.2.8.2.1 45HBV series mortise type locksets with security head screws (SH). Mortise lock

case meeting ANSI/BHMA A156.13, series 1000, grade 1 operational and grade 2 security for use on label doors up to 3 hours, "A" label.

2.8.2.2 9KV series cylindrical type locksets with security head screws (SH). cylindrical lock chassis, to meet ANSI/BHMA A156.2, series 4000, grade 1 operational, for use on label doors up to 3 hours, "A" label.

2.8.2.3 Exit device type trim shall be compatible to operate rim, mortise or vertical rod devices of designated manufacturers listed by standalone lockset manufacturer. Lever designs and escutcheons are to be of the same design and type as scheduled.

2.8.2.4 Swipe readers.2.8.2.5 Lockset programming maintained while changing the primary battery pack.2.8.2.6 Latchbolt Retraction: Enabled through the use of an internal motor. The internal

motor drive mechanism is activated by an electronic signal when presented with a valid magnetic stripe card and PIN. The latchbolts may also be operated by lever on either side of locksets, or push bar on exit devices, except when outside lever is locked by internal motor drive mechanism.

2.8.2.7 Mortise Locks: Solid stainless steel or solid hardened steel, with 1 inch (25 mm) throw deadbolt. Deadbolts operated by mechanical turn piece, inside. When deadbolts are extended, turning the inside lever retracts both the deadbolts and the latchbolts simultaneously. The locks have an electronic sensor that recognizes whether the deadbolt is retracted or thrown. The locks only grant access to deadbolt-authorized personnel when the deadbolt is thrown. Deadbolt

08 71 00-15

override cards for emergency level (programmable) shall be provided. Provide card locksets with key override feature. Keyed cylinders to be Best 7-pin keyway as designated and keyed into the existing grandmaster key system. No substitutions.

2.8.2.8 Provide key override sensors with mortise units. This feature detects when a key override has occurred and logs the event into history.

2.8.2.9 Cylindrical locks enabled through the use of internal solenoids or motors. The internal solenoid/motor drive mechanisms are operated by an electronic signal when presented with a valid magnetic stripe card and PIN. The latchbolts will also be operated by lever either side, except when outside lever is locked by an internal solenoid/motor drive mechanism.

2.8.2.10 Finish: BHMA as listed in the hardware sets.2.8.2.11 Lever Design: Match specified mechanical locksets.2.8.2.12 Permit free egress at all times from inside of room.2.8.2.13 Applicable for interior or covered exterior applications.2.8.2.14 Low battery indicator.2.8.2.15 After card swipe and PIN, green light indicates valid access; red light and

optional sounder indicate invalid access attempt.2.8.2.16 Cards to allow access to multiple rooms.2.8.2.17 Lost cards in system are replaceable and upon swipe of new sequential card the

lost card is invalidated in lock. This issuance of a new sequentially encoded card and invalidation process does not require reprogramming of lock by any means other than new card insertion into reader.

2.8.2.18 The lock resets to operating mode or on a programmable time should handle not be activated.

2.8.2.19 Card reader is designed to allow liquids to pass through unit and drain without affecting lock or electronics.

2.8.2.20 Furnish standard ANSI/BHMA A115.1 4 7/8 inch (124 mm) strike for locksets. Equip with easily seated, non-rising pins.

2.8.3 Electronic Lock Physical Characteristics:2.8.3.1 Lock not to protrude more than 4 1/4 inch (108 mm) from face of the door.2.8.3.2 Power Supply: 4, AA alkaline pack (included).2.8.3.3 Power Consumption: 20 mA in standby mode.2.8.3.4 Operational Temperature Range: Minus 31 degrees F to 150 degrees F (Minus

35 to 65.5 degrees C) with standard alkaline batteries.2.8.3.5 Humidity: Up to 95 percent without condensation.

2.8.4 Software Packages: Requirements to operate locking system hardware needed.2.8.4.1 Computer Hardware: 450 MHz Intel Pentium Processor, 64 MG Ram, 14/32 CD

Rom, 60 GB hard drive, 56k modem.2.8.4.2 Operating Systems: Win NT4 SP6a, Win 2000, Win Vista, MS Access (Office)PC

anywhere to be able to dial up,2.8.4.3 Programming cables.2.8.4.4 Capable of 65,000 users and 65,000 doors.2.8.4.5 Capable of 32 timetables with 5 shifts per timetable and 8 day types.2.8.4.6 Transaction log of computer transactions.2.8.4.7 Designed specifically for the residence hall application, addressing the real life

needs of daily operations such as lost cards or room changes.2.8.4.8 Allow batch data updating. A universal interface server provided to integrate the

university database.2.8.4.9 Networking multiple locations to a single database.2.8.4.10 Providing expiration date on the student cards preventing students from

returning to their rooms after the semester has expired.2.8.4.11 Providing offline lock and accepting "hardwire on-line" software, eliminating the

inefficiency of having two separate systems.

08 71 00-16

2.8.4.12 Capable of running a magnetic strip card encoder that "reads", "writes" and "overwrites with no data to have a blank card" information on the magnetic stripe card.

2.8.4.13 Capable of programming a portable lock-programming device, which allows the user to program the lock and retrieve lock history.

2.8.4.14 Magnetic strip encoder BASD-MSE provided; used to encode and validate cards.2.8.4.15 Provide One thousand (1,000) programmable PVC Cards - VPA-PVC with

system.

2.8.5 Portable Programmers: Hand held battery powered units that plug into the base of the locks by attached cable (included).2.8.5.1 Ability to upload/download programming information from software to locks

including but not limited to lock history.2.8.5.2 Perform diagnostic tests of locks.2.8.5.3 Password protection for opening a door.2.8.5.4 Capable of powering and opening locks and activating stand-alone card readers.2.8.5.5 Capable of lock interrogation providing system with an audit trail.2.8.5.6 Able to be programmed to inactivate itself after a specified amount of time,

maintaining security if lost or stolen.2.8.5.7 Physical Characteristics:

2.8.5.7.1 Weight: Less than one pound.2.8.5.7.2 Dimensions: Varies with manufacturer.2.8.5.7.3 Membrane keypad or LCD input screen.2.8.5.7.4 Memory Storage: 35 locks' data, plus 35 locks' openings records.

2.8.6 Direct Training for B.A.S.I.S: By authorized factory trained technician.2.8.6.1 Instruction to Owner's personnel on using the system software, portable

programmers, magnetic card encoders, and standalone electronic locks.2.8.6.2 Personnel must complete training prior to operating the system.2.8.6.3 Cost to be included in hardware quotation.2.8.6.4 Any training required, after initial training will be quoted by the manufacturer.2.8.6.5 Approved Operating Systems:

2.8.6.5.1 Windows 7 Professional (32 & 64 Bit).2.8.6.5.2 Windows 8 and 8.1 Update (32 & 64 Bit).2.8.6.5.3 Windows Server 2012 Standard and Enterprise (64 Bit).2.8.6.5.4 Windows Server 2012 R2 Standard and Enterprise (64 Bit).

2.8.6.6 Required Hardware:2.8.6.6.1 Processor: Pentium IV Dual Core 3.4 GHz or faster.2.8.6.6.2 Memory: Minimum 2 GB.2.8.6.6.3 Hard Drive: Minimum 6 GB of available space.2.8.6.6.4 DVD-ROM2.8.6.6.5 USB-Port.2.8.6.6.6 Display: 1024x768, Color.

2.9 EL SERIES ELECTRONIC LOCKS

2.9.1 EL Series Mechanical Lock Specifications:2.9.1.1 BHMA certified complying with ANSI/BHMA A156.2, series 4000, grade 2, UL

10C-90 minutes, ADA.2.9.1.2 Fits ANSI/BHMA A115.2 (160 &161) door preparation.2.9.1.3 Locksets and cores to be from same manufacturer to maintain complete lockset

warranty.2.9.1.4 Backset: Fits 2-3/4 inch (70 mm).2.9.1.5 Latchbolt Throw: 1/2 inch (13 mm).2.9.1.6 Mechanical Warranty: 2 years.2.9.1.7 Keyed lever removable only after core is removed, by authorized control key.

08 71 00-17

2.9.1.8 7-pin removable "SFIC" interchangeable cores.2.9.1.9 Case Material: Combination of zinc alloy and fire retardant ABS.2.9.1.10 Classroom/Storeroom function -71 and "M" Summit design.

2.9.2 Electronic Lock Specifications:2.9.2.1 Users: Up to 1000. For standalone; 200 users minimum.2.9.2.2 Standalone keyless entry upgradeable to wireless option.2.9.2.3 Wireless Entry: Industry standard 128-bit-based security encryption.2.9.2.4 Audit Trail: 500 events for wireless communication only; stored locally.2.9.2.5 Credential Verification Time: One second or less.2.9.2.6 Visual/Audible Interface: Tri-Colored LED with field configurable audible

indicator.2.9.2.7 System Interface: Stanley wireless gateway (Wireless Only).2.9.2.8 Power Supply: 4 AA batteries. Battery life up to 2 years, depending on usage.2.9.2.9 Certifications and Compliance: FCC Part 15 B&C, RoHS.2.9.2.10 Reader Technology Proximity: 125 kHz.2.9.2.11 Wiegand Proximity Cards: 125 kHz credential compatibility2.9.2.12 Wireless Communication Interface: IEEE802.15.4 (2.4 GHz).2.9.2.13 Communication Security: AES 128-bit Encryption.2.9.2.14 Wireless Communication Protocol: Stanley proprietary.2.9.2.15 Electronic Warranty: 1 year.

2.9.3 Gateway Specifications:2.9.3.1 Power PoE: (IEEE 802.3 af) or 24 V DC / 1Amp. ac/dc adaptor sold separately.2.9.3.2 LAN Communication Interface Ethernet: TCP/IP (IEEE 802.3).2.9.3.3 Wireless Communication Interface: IEEE 802.15.4 (2.4 GHz).2.9.3.4 Configuration Interface: Web based portal.2.9.3.5 Wireless Communication Protocol: Stanley proprietary.2.9.3.6 Access Control Management Software: PAC Access Control System.

2.9.4 Electronic EZ Keypad Series Lock Software Features:2.9.4.1 Variable PIN Length: 3 to 6 digits.2.9.4.2 Maximum Users: 50.2.9.4.3 Programming: Only through keypad.2.9.4.4 Passage Mode: Authorized users can unlock device for extended periods.2.9.4.5 1 administrator PIN and 5 supervisor PIN's to manage groups of users.

2.9.5 EXZ Keypad Exit Device Trim:2.9.5.1 Rim Devices.2.9.5.2 Surface vertical rod.2.9.5.3 Concealed vertical rod.2.9.5.4 Mortise lock: ANSI/BHMA A115.1.2.9.5.5 UL listed for GYQS electrically controlled single point locks or latches for use on

3 hour "A" label doors.2.9.5.6 Function "EV" with key override -7, or "NV" without key -0.2.9.5.7 Lever style Best 14 or 15. Trim accepts Best 7 pin cores.2.9.5.8 PH2 for Precision 2000 series exit device.2.9.5.9 VD9 for VonDuprin 98/99 Series.

2.9.6 EXZ Electronic Characteristics:2.9.6.1 Primary Power: Alkaline battery pack.2.9.6.2 Operational Temperature Range: Minus 22 to 140 degrees F (minus 30 to 60

degrees C) with standard alkaline battery pack.2.9.6.3 Relative Humidity: 10 to 905 percent non-condensing.2.9.6.4 Shock: 2000 Gs RMS (Maximum door-slam shock).

2.9.7 EXZ Keypad:

08 71 00-18

2.9.7.1 Bezel Size: 2-5/8 x 3-1/4 inches (67 x 83 mm).2.9.7.2 Material: Bezel - high impact ABS; keypad - silicone rubber.2.9.7.3 EDS Protection: 15KV.2.9.7.4 Button Operating Life: 3 to 5 million cycles.2.9.7.5 Sealing: Weather-resistant gasket provides protection for covered outdoor use.

2.9.8 Cylindrical EZ Type Locks:2.9.8.1 Fit modified ANSI/BHMA A115.2 door preparation series 4000, mount housing.2.9.8.2 Levers to be controlled by independent spring mechanisms.2.9.8.3 Trim accepts Best 7 pin cores.2.9.8.4 Standard Backset: Fits 2-3/4 inch (70 mm).2.9.8.5 Latchbolt Throw: 9/16 inch (14 mm).2.9.8.6 Lever Material: High quality zinc alloy. Handle is approximately 4-3/4 inch (121

mm) long.2.9.8.7 Keyed lever removable only after core is removed, by authorized control key2.9.8.8 7-pin removable and interchangeable core cylinders2.9.8.9 Hub, side plate, shrouded rose, and locking pin in one-piece casting with a

shrouded locking lug.2.9.8.10 Locksets outside locked lever must withstand minimum 1400 inch pounds of

torque. In excess of that, a replaceable part will shear. Key from outside and inside lever will still operate lockset.

2.9.9 Electronic EZ Keypad Series Lock Software features:2.9.9.1 Variable PIN Length: 3 to 6 digits.2.9.9.2 Maximum Users: 50.2.9.9.3 Programming: Only through keypad.2.9.9.4 Passage Mode: Authorized users can unlock device for extended periods.2.9.9.5 1 Administrator PIN and 5 Supervisor PIN's to allow easy management of groups

of users.

2.9.10 EZ Electronic Characteristics:2.9.10.1 Primary Power: Alkaline battery pack.2.9.10.2 Operational Temperature Range: Minus 22 to 140 degrees F (minus 30 degrees

C to 60 degrees C) with standard alkaline battery pack.2.9.10.3 Relative Humidity: 10 to 905 percent non-condensing.2.9.10.4 Shock: 2000 Gs RMS (Maximum door-slam shock).

2.9.11 EZ Keypad:2.9.11.1 Bezel Size: 2-5/8 x 3-1/4 inch (67 x 83 mm).2.9.11.2 Material: Bezel - high impact ABS; keypad - silicone rubber.2.9.11.3 EDS Protection: 15KV.2.9.11.4 Button Operating Life: 3 to 5 million cycles.2.9.11.5 Sealing: Weather-resistant gasket provides protection for covered outdoor use.

2.10 PAC ACCESS CONTROL SYSTEM

2.10.1 Electronic Access Control System Basis of Design: Stanley PAC System.2.10.1.1 Provide access control components including but not limited to controllers,

enclosures, power supplies, reader devices, system credentials, card enrollment device, software and one client server as required for complete functional system.

2.10.1.2 BHMA certified complying with ANSI/BHMA A156.2, series 4000, grade 2, UL 10C-90 minutes, ADA. System to have a minimum of 15 years usage history.

2.10.1.3 Compatible with Windows 7 and 8, 32 bit and 64 bit.2.10.1.4 Complete system to control and monitor in real time a minimum of 250 readers

and 25,000 cardholders.2.10.1.5 Scalable for later expansion.

08 71 00-19

2.10.1.6 Programmable up to 20 individual programmable time schedules and 100 individual programmable holidays.

2.10.1.7 Controller to operate as a fully independent system even when communication to the PC or other controllers are not available.

2.10.1.8 Event Buffer: 16,000 event minimum.2.10.1.9 Provide door controllers that manages two doors in a lockable metal power

supply enclosure, pre-wired 24 V DC, 3 Amp.2.10.1.10 Capable of both ethernet TCP/IP or RS485 communication.2.10.1.11 Programmable request to exit and door contact.2.10.1.12 Readers mounted on a single vertical gang electrical box, with reading range of

3 1/6 inch (78 mm).2.10.1.13 Proximity cards or key fobs each pre-programmed with a unique ID that reads

125kHz proximity formats.2.10.1.14 Include enrollment reader that can be connected to either the host PC or a client

workstation.2.10.1.15 Acceptable manufacturer and type: Stanley PAC Access Control System.

2.10.2 Electromagnetic Locks: BHMA Certified complying with ANSI/BHMA A156.23; electrically powered, of strength and configuration indicated; with electromagnet attached to frame and armature plate to door.2.10.2.1 Type: Full exterior or full interior, as required by application indicated.2.10.2.2 Strength Ranking: 1500 lbf (6672 N).2.10.2.3 Strength Ranking: 1000 lbf (4448 N).2.10.2.4 Strength Ranking: 500 lbf (2224 N).2.10.2.5 Inductive Kickback Peak Voltage: Not more than 53 V.2.10.2.6 Inductive Kickback Peak Voltage: Not more than 0 V.2.10.2.7 Residual Magnetism: Not more than 4 lbf to separate door from magnet.2.10.2.8 Residual Magnetism: Not more than 0 lbf to separate door from magnet.

2.10.3 Power Supply: UL listed. Designed to support electric locks and access controls.2.10.3.1 Input: 115 V AC at 800 mA expandable to four station controls.2.10.3.2 Output Power: Filtered, regulated, and field selectable for 12 or 24 V DC.2.10.3.3 Fire alarm/life safety emergency release included in power supply.2.10.3.4 Available Multiple Door Options:

2.10.3.4.1 Four or more control stations.2.10.3.4.2 Adjustable time delay relay.2.10.3.4.3 Battery charging.2.10.3.4.4 Battery backup.

2.10.4 Door Position Switch: For door status monitoring as indicated in hardware sets.2.10.4.1 At fired rated doors and frames, position switch preparation will be provided by

the door and frame manufacturer or by an authorized label service agent.

2.10.5 Quick Connect Plug-In Connectors: Stanley quick connect plug-in must be used with a combination of the following components to work as a complete plug and play system.2.10.5.1 Best locks series 45HW, 45HM, 8KW, 9KW, and 9KM, including quick

connectors to Best lock products suffix "C" Example (45HW-7DEL14H DS C).2.10.5.2 Precision Exit Devices 2000 Series, DE, DS, TS, TDS, LDS, and ELR including

quick connectors to Precision electric exit device products prefix "C" Example (C ELR 2108 x V4908A TS).

2.10.5.3 Precision 12 Conductor Electric Power Transfer EPT-12C.2.10.5.4 Stanley 12 Hinges Conductor Hinge CECB179-12C.

2.10.6 Quick Connect Wire Harnesses: One four wire connector and one eight wire connector. The four wire connector has two 18AWG and two 24AWG wires. The eight wire connector has eight 24 AWG wires. Lengths to be recommended by manufacturer.2.10.6.1 Wire Harnesses terminated at both ends: WH-size (Example WH-3).

08 71 00-20

2.10.6.2 Wire Harness terminated at one end with exposed pin head at the other: WH-size P.

2.10.6.3 Wire Harness 6 inch (152mm) terminated one end, bray leads on the other: WH-6E.

2.10.6.4 Wire harnesses with suffix "E" has brae wire ends, used to connect the quick connect harness to a hardwired connection.

2.11 BEHAVIORAL HEALTHCARE SYSTEM

2.11.1 Behavioral Healthcare Solutions: Include components specifically designed to be used as a complete operational system.2.11.1.1 Typical Installation Includes:

2.11.1.1.1 Electrified power transfer hinge.2.11.1.1.2 Door sensor assembly.2.11.1.1.3 Reset key switch.2.11.1.1.4 Strobe light.2.11.1.1.5 Controller and Power Supply, for applications with up to 12, 24 or 36 doors.2.11.1.1.6 Console for Desk or Wall mounted provides remote real-time visual and

audible status. Console to monitor 12, 24, or 36 Door Sensor Assemblies.

2.11.2 Cylindrical Type Locks and Latchsets:2.11.2.1 BHMA Certified in compliance with ANSI/BHMA A156.2, Series 4000,

operational grade 1, extra-heavy duty, and be UL 10C listed.2.11.2.2 Comply with 9001 - Quality Management and 14001 - Environmental

Management.2.11.2.3 Fits modified ANSI/BHMA A115.2 door preparation.2.11.2.4 Locksets and cores to be from same manufacturer to maintain complete lockset

warranty.2.11.2.5 Locksets to have anti-rotational studs that are thru-bolted.2.11.2.6 Keyed levers not to have exposed "keeper" holes.2.11.2.7 Levers to have independent spring mechanisms controlling them.2.11.2.8 Backset: Fits 2-3/4 inch (70 mm).2.11.2.9 Latchbolt Throw: 9/16 inch (14 mm).2.11.2.10 Curved strike lip to protect door trim.2.11.2.11 Outside Lever Sleeve: Seamless, one-piece construction of a hardened steel

alloy.2.11.2.12 Keyed Lever: Removable only after core is removed, by authorized control key.2.11.2.13 7-pin removable and interchangeable core cylinders.2.11.2.14 Hub, side plate, shrouded rose, locking pin one-piece casting with shrouded

locking lug.2.11.2.15 Locksets outside locked lever must withstand minimum 1400 inch pounds (635

kg) of torque. In excess of that, a replaceable part will shear. Key from outside and inside lever will still operate lockset.

2.11.2.16 Core face must be the same finish as the lockset.2.11.2.17 Functions and design as indicated in the hardware groups.

2.11.3 BEST Cylindrical Type Locks and Latchsets using Stanley PAC:2.11.3.1 BHMA certified complying with ANSI/BHMA A156.2, series 4000, operational

grade 1, extra heavy duty. UL 10C listed.2.11.3.2 Fits modified ANSI/BHMA A115.2 door preparation.2.11.3.3 Locksets to have anti-rotational studs that are thru-bolted.2.11.3.4 Levers to have independent spring mechanisms controlling them.2.11.3.5 Backset: Fits 2-3/4 inch (70mm).2.11.3.6 Latchbolt Throw: 9/16 inch (14mm).2.11.3.7 7-pin removable and interchangeable core cylinders.2.11.3.8 Core face must be the same finish as the lockset.

08 71 00-21

2.11.3.9 Provide electric operation as defined and required.2.11.3.10 Provide request to exit switch (RQE) and door position switch (DS).

2.11.4 Door Controllers:2.11.4.1 Embedded Ethernet TCP/IP Support over LANs and WANs. DHCP or fixed IP.2.11.4.2 In the event of ethernet communications failure, the server can be programmed

to communicate back over dialup PSTN connection providing redundancy.2.11.4.3 Operates normally in the event of lost communications with the server. Upon

communications restoration, events are automatically uploaded to the server.2.11.4.4 FLASH Memory Up-gradable.2.11.4.5 100 mb ethernet and 56,000 bps serial communication speed.2.11.4.6 Encrypted Communications: 250,000 key holder database (nonvolatile).2.11.4.7 128 Doors served per subsystem.2.11.4.8 32 slave controller units on RS-485 Channel.2.11.4.9 Event Buffer Memory: 10,000 events.2.11.4.10 1 RS-232 channel bi-directional.2.11.4.11 2 RS-485 channels bi-directional.2.11.4.12 One-touch installation testing.2.11.4.13 Plug and play network detection with no switches needing to be set.2.11.4.14 PSTN connectivity via external modem for dual host communication.2.11.4.15 Tamper and door override inputs.2.11.4.16 200 Mhz Intel X-Scale processor 32mb flash and 32mb RAM. 12 or 24 V DC

powered.

2.11.5 Readers:2.11.5.1 Slimline configuration.2.11.5.2 Stainless steel vandal resistant configuration.2.11.5.3 Audible feedback to indicate granted or denied decisions.2.11.5.4 Multicolor status LED.2.11.5.5 AC, Wiegand 26 bit. AC 512 door controllers provide full alarm monitoring of

STANLEY card readers.2.11.5.6 Tamper protection.2.11.5.7 Read Ranges: Between 0.5 and 9.5 inches (13 and 241 mm).2.11.5.8 IP 66 Rating: 12V DC input power.

2.11.6 Proximity Cards:2.11.6.1 Comply with ISO Standards. Offer over 1 billion different codes.2.11.6.2 Polyvinyl chloride (PVC) for image printing. Include landscape holders and heavy

duty badge reels, with sealed polycarbonate.2.11.6.3 Dimensions: 2-1/8 inch (54 mm) high; 3-3/8 inch (86 mm) wide; 0.030 inch (0.76

mm) thickness.2.11.6.4 125 Khz radio frequency to transmit encoded microchip numbers when

activated.2.11.6.5 Provide minimum 100 programmed cards.

2.12 EXIT DEVICES

2.12.1 Exit Device Requirements:2.12.1.1 BHMA certified complying with ANSI/BHMA 156.3, grade 1.2.12.1.2 Comply with 9001 - Quality Management and 14001 - Environmental

Management standards.2.12.1.3 Tested and certified by UL or by a recognized independent laboratory for

mechanical operational testing to 10 million cycles minimum with inspection confirming grade 1 loaded forces have been maintained.

2.12.1.4 UL-Listings: UL 10C at fire door assemblies, UL listed for panic at non-rated door assemblies, UL listed for accident hazard.

2.12.1.5 Non-fire rated exit devices to have cylinder dogging and 1/4 inch (6 mm)

08 71 00-22

minimum turn hex key dogging.2.12.1.6 Size to proper door width and height.

2.12.2 Exit Device Construction:2.12.2.1 Exposed components to be of architectural metals and "true" architectural

finishes.2.12.2.2 Chassis: Investment cast steel, zinc dichromate.2.12.2.3 Exit Device: Heavy investment cast stainless steel.2.12.2.4 Latch Bolt: Stainless steel deadlocking 3/4 inch (19 mm) through bolt.2.12.2.5 Activators consist of a cross bar or push pad, the actuating portion of which

extends across, and not less than one half the width of the door leaf.2.12.2.6 Levers: Lever design to match lockset lever design. Provide heavy-duty vandal

resistant lever trim with heavy-duty investment cast stainless steel components and extra strength shock absorbing overload springs. Lever shall not require resetting.

2.12.2.7 Field reversible handing.2.12.2.8 LBR (less bottom rod) where scheduled to eliminate use of floor mounted strikes.

Provide strikes as required by application, typically with black powder coated finish.

2.12.2.9 Aluminum vertical rod assemblies are acceptable only when provided with manufacturer's optional top and bottom stainless steel rod guard protectors.

2.12.2.10 Vertical Latch Assemblies: Gravity operation, no springs.2.12.2.11 Vandal resistant or breakaway trim.2.12.2.12 Approved Manufacturers and Products: Precision Apex 2000 Series.

2.13 DOOR CLOSERS

2.13.1 Door Closers General Requirements:2.13.1.1 BHMA certified complying with ANSI/BHMA 156.4, Grade 1. UL 10C certified.2.13.1.2 Comply with 9001 - Quality Management and 14001 - Environmental

Management.2.13.1.3 Closer shall have extra-duty arms and knuckles. Conform to ANSI 117.12.13.1.4 Maximum 2-7/16 inch (62 mm) case projection with non-ferrous cover.2.13.1.5 Separate adjusting valves for closing and latching speed, and back check.2.13.1.6 Provide adapter plates, shim spacers and blade stop spacers as required by

frame and door conditions.2.13.1.7 Full rack and pinion type closer with 1-1/2 inch (38 mm) minimum bore.2.13.1.8 Mount closers on non-public side of door, unless otherwise noted in

specification.2.13.1.9 Non-handed, non-sized and multi-sized.

2.13.2 Cast Iron Surface Door Closers:2.13.2.1 BHMA certified complying with ANSI/BHMA A156.4 grade 1.2.13.2.2 Extra heavy duty cast iron door closers.2.13.2.3 Furnish manufacturers recommended size, arms and configuration for door and

frame application required.2.13.2.4 Furnish brackets, spacers, support shoes, and plates for proper installation.2.13.2.5 DA (delayed-action) at toilet room doors and as scheduled.2.13.2.6 Acceptable Manufacturers and Products: Stanley QDC100 Series, LCN 4040XP,

Series, Sargent 281 Series.

2.13.3 Aluminum Surface Door Closers:2.13.3.1 BHMA certified complying with ANSI/BHMA A156.4 Grade 1.2.13.3.2 Heavy duty cast iron or aluminum body closers.2.13.3.3 Furnish manufacturers recommended size, arms and configuration for door and

frame application required.2.13.3.4 Furnish brackets, spacers, support shoes, and plates for proper installation.

08 71 00-23

2.13.3.5 DA (delayed-action) at toilet room doors and as scheduled.2.13.3.6 Acceptable Manufacturers and Products: Stanley CL D-4550 Series, LCN

4040XP Series, Norton 7500 Series.

2.14 AUTOMATIC OPERATORS

2.14.1 Automatic Operators General Requirements:2.14.1.1 BHMA certified complying with ANSI/BHMA A156.10 and A156.19 and suitable

for full energy and low energy.2.14.1.2 Listed under UL 10C and UL 325. Non-handed.2.14.1.3 Capable of functioning on doors weighing 350 lb (159 kg).2.14.1.4 Incorporate the Following Adjustment Capabilities: Opening force, closing force,

open speed, close speed, and open check speed with separate on-off-hold open switch.

2.14.1.5 Incorporate a non-ferrous cover not exceeding 6 inches (152 mm) square in section.

2.14.1.6 Microprocessor controlled with position encoder.2.14.1.7 Readily function with standard activation and safety sensors, provide activation

devices where required.2.14.1.8 Power open / close with power, function as a manual door closer without power.2.14.1.9 Function with 115 VAC electrical service for operator and standard low voltage

connections for activation.2.14.1.10 Units must be furnished and installed.2.14.1.11 Acceptable Products and Manufactures: Stanley "Magic-Force" series or

accepted equal by LCN or Norton.

2.15 LOW ENERGY OPERATORS

2.15.1 Low Energy Operators General Requirements:2.15.1.1 BHMA certified complying with ANSI/BHMA A156.19 as a low energy power

opening device.2.15.1.2 Listed under UL 228, UL 325, UL10B, UL 10C, UBC 7.2 and FCC listed.2.15.1.3 Non-handed. Rated for door panels weighing up to 350 pounds (159 kg).2.15.1.4 Manual Door Closers within Low Energy Operators: Meet Americans with

Disabilities Act (ADA); 5 pounds (2.26 kg) opening force for Push-Side applications.

2.15.1.5 Wall-Mounted Actuator Switches: by same manufacturer as the operator. Use weather-resistant actuators for exterior applications.

2.15.1.6 Operators isolated from mounting plates with rubber mounts to mitigate the transmission of forces between the door and the operator.

2.15.1.7 Position encoders to communicate with microprocessor.2.15.1.8 Resettable powered operation counter that tracts both powered and non-

powered cycling of the operator.2.15.1.9 Adjustable Settings: Hold open timer, to 28 seconds, open speed, back check

speed, vestibule sequence timer.2.15.1.10 DIP Switch Controls: On board diagnostics, power close, push-and-go operation,

and time delay logic for electrified hardware components.2.15.1.11 Terminals for Auxiliary Controls: Activation devices with two discrete inputs, and

vestibule sequencing.2.15.1.12 Control Switches: Day/night open (illuminated), power on-off.2.15.1.13 Include adhesive low energy operator mounting templates.2.15.1.14 Non-powered operation: Units function as standard door closers with adjustable

spring force size 1 thru 6.

2.16 DOOR STOPS

2.16.1 Floor and Wall Stops: Dome, cast floor or wall stops for every opening as listed in the

08 71 00-24

hardware sets.2.16.1.1 Concave Wall Stops: Turn piece or push button on lockset handle makes contact

with stop.2.16.1.2 Convex Wall Stops: Turn piece or push button on lockset handle does not makes

contact with stop.2.16.1.3 Wrought bronze, brass or stainless steel as scheduled.2.16.1.4 Provide fasteners suitable for construction.2.16.1.5 Coordinate reinforcement of walls where wall stops are installed.2.16.1.6 Provide floor dome stops where wall stops are not practical. Provide spacers or

carpet riser for floor conditions encountered.

2.16.2 Over-Head Stops:2.16.2.1 For interior doors and any doors that swing more than 140 degrees before

striking a wall, open against equipment, casework, sidelights, and where conditions do not allow a wall stop or a floor stop presents a tripping hazard.

2.16.2.2 Friction type: Doors without closers.2.16.2.3 Positive type: Doors with closers.2.16.2.4 Concealed Overhead Stops: Heavy-duty bronze or stainless steel as scheduled.2.16.2.5 Surface Overhead Stops: Heavy-duty bronze or stainless steel as scheduled.2.16.2.6 Acceptable Products and Manufacturers:

2.16.2.6.1 ABH: 1000SL series, 1000 series, and 9000 Series.2.16.2.6.2 Dorma: 700 series, and 900 series

2.17 DOOR PROTECTION

2.17.1 Acceptable Manufacturers: Trimco, Burns, Rockwood, Hiawatha.

2.17.2 Push Plates: Provide with four beveled edges ANSI J301, 6 inches (152 mm) wide x 16 inches (406 mm) high 0.050 inch (1.27 mm) thick, or as indicated in hardware set. Furnish oval-head countersunk screws to match finish. Where width of door stile prevents use of 6 inches (152 mm) wide plate, adjust width to fit.

2.17.3 Pulls With Plates: Provide, with four beveled edges ANSI J301, 4 inches (102 mm) wide x 16 inches (406 mm) high x 0.050 inch (1.27 mm) thick plates with ANSI J401 Pulls as listed in hardware sets. Provide proper fasteners for door construction. Where required, mount back to back with push bar.

2.17.4 Push Pull Bars: Provide ANSI J504, 0.1 inch (2.54 mm) diameter pull and push bar model and series as listed in hardware set. Provide proper fasteners for door construction.

2.17.5 Push Bars: Provide solid bar stock, diameter and length as scheduled. Push bars shall be of sufficient length to span from center to center of each stile. Where required, mount back to back with pull.

2.17.6 Kickplates: Where bottom rail allows, provide with four beveled edges ANSI J102, 10 inches (254 mm) high by width less 2 inches (51 mm) on single doors and 1 inch (25 mm) on pairs of doors. Furnish oval-head countersunk screws to match finish.2.17.6.1 Acceptable Products: Trimco KO050, Rockwell K1125, Burns KP50, Hiawatha

KP.

2.17.7 Mop Plates: Provide with four beveled edges ANSI J103, minimum 4 inches (102 mm) high by width less 1 inch (25 mm) on single doors and 1 inch (25 mm) on pairs of doors. Furnish oval-head countersunk screws to match finish.

2.17.8 Armor Plates: ANSI J101 with four beveled edges, 40 inches (1016 mm) high by width less 1 inch (25 mm) on single or pairs of doors. Oval head countersunk screws to match finish.

08 71 00-25

2.17.8.1 Provide cutouts for hardware as listed in the hardware sets.2.17.8.2 Warnock Hersey labeled plates for 3 hour metal fire doors where allowed.

2.18 ELECTRIC STRIKES

2.18.1 Electric Strikes: BHMA Certified in compliance with ANSI/BHMA 156.31, grade 1, listed for burglary protection ANSI/ UL1034 grade 1, and UL 10C for fire door assemblies.2.18.1.1 General Use: Fail-secure.2.18.1.2 Fire-Rated Device: Field selectable fail safe/fail secure modes.2.18.1.3 Accept 5/8 or 3/4 inch (16 or 19 mm) latchbolt.2.18.1.4 Latchbolt monitor switch option when specified in hardware sets.2.18.1.5 Non-handed 24 V DC electric strike suitable for door frame material and lock

configuration scheduled. Include transformer and rectifier for complete installation.

2.18.1.6 Tie electric strikes into fire alarm where non-rated doors are scheduled to release with fire/sprinkler alarm condition.

2.18.1.7 Acceptable Manufacturers: Stanley ES-4, SDC: 45 Series, RCI: 4 Series.

2.18.2 ES4 Electric Door Strike: ANSI/ UL1034 listed.2.18.2.1 Field selectable, fail secure or failsafe.2.18.2.2 Accept 5/8 or 3/4 inch (16 or 19 mm) latchbolt.2.18.2.3 Dual Voltage coil 200/100 mA at 12/24V DC, 140/70 mA at 12/24 V AC.2.18.2.4 Keeper Closed and Locked Status S: SPDT, Dry 3 Amp at 30 V.2.18.2.5 Keeper Open/Closed Status K: SPDT, Dry 3 Amp at 30 V.2.18.2.6 Faceplate Options Suffix: As recommended by the manufacturer.

2.18.3 ES5 Electric Door Strike: ANSI/UL1034 and Warnock Hersey listed.2.18.3.1 Accept up to a 3/4 inch (19 mm) latch bolt and 1 inch (25 mm) deadbolt.2.18.3.2 Field reversible, fail secure or failsafe.2.18.3.3 Listed UL 10C fire door assemblies for single door applications.2.18.3.4 UL tested 1500 lb (680 kg) static strength.2.18.3.5 Dual voltage coil 600 mA @ 12V DC, 300mA at 24 V AC2.18.3.6 Contacts: SPDT, Dry, 5 Amp at 30 V.2.18.3.7 Latchbolt Monitor (LBM): Signals door is closed and latched or unlatched and

open.2.18.3.8 Door Secure Monitor (LBM/LCM): Signals door is closed and latched or

unlatched and open.2.18.3.9 Deadbolt Monitor (DBM): Signals deadbolt projected or retracted.

2.19 ACCESSORIES

2.19.1 Thresholds: Aluminum beveled type with maximum height of 1/2 inch (13 mm) for conformance with ADA requirements, as scheduled and per details. Fasteners and screws suitable for floor conditions. Returned closed ends at openings where threshold extends beyond frame face. Neoprene inserts at panic type thresholds.

2.19.2 Gasketing: Rigid jamb weatherstrip with replaceable silicone insert. Include self-adhesive two-sided tape in addition to manufacturer's standard fastener. Meeting-stile gasketing required at exterior pairs of doors and doors in smoke partitions. Flexible adhesive fire/smoke gasketing at "S" labeled openings.

2.19.3 Weatherstripping: At head and jambs for only those units where resilient or flexible seal strip is easily replaceable. Where bar-type weatherstrip is used with parallel arm mounted closers install weatherstrip first.2.19.3.1 Weatherstrip: Resilient seal of (Neoprene, Polyurethane, Vinyl, Pile, Nylon

Brush, Silicone).2.19.3.2 UL 10C Positive Pressure rated seal set when required.

08 71 00-26

2.19.4 Door Bottoms and Sweeps: Surface mounted or concealed door bottom where listed in the hardware sets. Sweeps to have adjustable screw holes. Sweeps with rain drips on exterior in-swing doors. Sweeps with neoprene inserts on exterior out-swing doors.2.19.4.1 Door Seal: Resilient seal of (Neoprene, Polyurethane, Nylon Brush, Silicone).2.19.4.2 UL 10C Positive Pressure rated seal set when required.

2.19.5 Electromagnetic Door Holders: Wall mounted, extension arms to accommodate wall conditions, voltage 120VAC.2.19.5.1 Acceptable Manufacturers and Products: ABH 2100, Rixson 998, LCN

SEM7850.

2.19.6 Silencers: Rubber silencers installed with injector tool on interior frames; 3 for single doors, 2 for pairs. Omit where any type of seal occurs.

2.19.7 Key Cabinets: Wall mounted with one hook for each lock or cylinder plus fifty extra hooks to accommodate 50 percent expansion. Coordinate mounting location with architect. One non-removable security tag and one snap-on link duplicate tag per hook. Furnish tools, instructions sheets and accessories required to complete installation. Owner or their representative will place keys in cabinet and complete index card furnished with key system.2.19.7.1 Acceptable Manufacturers: Lund, Telkee, MMF.

2.19.8 Key Control Software: Keystone 600N key management control software unless otherwise indicated.2.19.8.1 Software Features:

2.19.8.1.1 Password restricted logins.2.19.8.1.2 List keys and items currently due back (or due back by any day

designated).2.19.8.1.3 Lists cores and their location, building and doors, and cross-references

people to cores, doors, and building they access.2.19.8.1.4 Comprehensive list of reports available as an on-screen menu.2.19.8.1.5 Built-in easy to use backup program.2.19.8.1.6 Program always displays date of last backup.2.19.8.1.7 Dynamic searching capabilities for records.2.19.8.1.8 On-screen indicator shows when historical info. Is present for a record.2.19.8.1.9 On-screen indicator appears when notes are present on a record.2.19.8.1.10 Able to operate in an NTFS network environment with TCPIP protocol.2.19.8.1.11 Multiple users can access program at the same time.2.19.8.1.12 Software to include a "Best" Automated Pin Segment Calculator and a

Manual Pin Segment Calculator for authorized "Best" building lock shop facilities.

2.19.8.1.13 Software program compatible with Owner's operating system and TCPIP protocol.

2.19.9 Coordinator and Brackets: Provide surface mounted coordinators when automatic bolts are used in the hardware set.2.19.9.1 Coordinator: BHMA Certified complying with ANSI/BHMA A156.3 type 21A for

full width of the opening.2.19.9.2 Mounting brackets for soffit applied hardware.2.19.9.3 Hardware preparation (cutouts) for latches as necessary.2.19.9.4 Acceptable Manufacturers: Trimco, ABH, Burns.

2.19.10 Power Supply for Electric Latch Retraction (ELR) Exit Devices:2.19.10.1 Motherboard accepting up to four plug-in control modules. Provide appropriate

necessary control module to operate the number of ELR exit devices used at each opening. The control module is to include a time delay feature variable (0 to 4 minutes) latch retraction period in response to a momentary input.

2.19.10.2 UL Listed for class II output. Circuit breakers for protection of motherboard

08 71 00-27

2.19.10.3 115 or 230 V user selectable switch, with V AC input of 115 Volt at 1 A.2.19.10.4 Control module includes fire alarm terminal and auxiliary contacts for remote

signaling.

2.19.11 Power Supply Precision PS161 for Delayed Egress Devices, Electric Locking, and Exit Alarms:2.19.11.1 120 V AC at 0.8 A input.2.19.11.2 Able to control up to 4 delayed egress exit devices.2.19.11.3 Filtered and regulated output power 24 V DC at 6 A.2.19.11.4 Fire alarm release to accept normally closed contact.2.19.11.5 V AC input protected via manually reset circuit breaker.2.19.11.6 V DC output is protected via an auto-reset fuse (PTC). Box to include a key lock.

2.19.12 Battery Backup (BT) power tap module to operate a card reader or when ELR devices require battery backup.2.19.12.1 Provide Precision ELR150 series with the required modules.2.19.12.2 Lead acid batteries are not included and are to be furnished by others.

2.19.13 Provide power transfer types as recommended by manufacturer for each condition including:2.19.13.1 Precision EPT-12C quick connect power transfers.2.19.13.2 Precision EPT-5 power transfers.2.19.13.3 Precision EPT-2 surface mounted door loop power transfer.2.19.13.4 Von Duprin EPT series.

2.20 FlNlSHES

2.20.1 Hardware Finishes: As listed in ANSI/BHMA A156.18, designated in Hardware Schedule, including coordination with traditional finishes shown by manufacturers for their products.

2.20.2 Provide the following finishes unless otherwise scheduled:2.20.2.1 Exterior Hinges: 630, Satin Stainless Steel.2.20.2.2 Interior Hinges: 626 or 652, Satin Chrome.2.20.2.3 Locks and Latches: 626, Satin Chrome.2.20.2.4 Exit Devices: 630, Satin Stainless Steel.2.20.2.5 Exit Devices: 626W, Chrome Plated over Brass.2.20.2.6 Door Closers: 689, Spray Painted Aluminum.2.20.2.7 Push/Pulls: 630, Satin Stainless Steel.2.20.2.8 Protection Plates: 630, Satin Stainless Steel.2.20.2.9 Stops and Holders: 630, Satin Stainless Steel.2.20.2.10 Thresholds/Gasket: AL, Anodized Mil Finished Aluminum.2.20.2.11 Powder coat door closers to match other hardware, unless otherwise noted.2.20.2.12 Finish aluminum items to match predominant adjacent material.2.20.2.13 Seals and silencers to coordinate with frame colors.

3 EXECUTION

3.1 EXAMINATION

3.1.1 Examine and measure installation areas are prepared to receive doors and site conditions are within the manufacturers limits.

3.1.2 Examine doors, frames, related items and conditions under which Work is to be performed and identify conditions detrimental too proper and or timely completion.3.1.2.1 Verify doors and frames are plumb, square, level and true and free from defects

that would prevent proper installation of finish hardware.3.1.2.2 Confirm blocking material is installed for wall mounted door stops at height

08 71 00-28

appropriate to contact door trim.

3.1.3 Verify power is run to doors requiring electrified hardware. Do not begin installation until necessary building services are installed.3.1.3.1 Electrical installer to provide conduit and electrical wiring for activating devices

and door operators.3.1.3.2 Unless otherwise specified or required by the manufacturer, provide a minimum

of 5 amperes, 115 volts, A/C, 1-phase circuit for each door operator, terminate and connect to operator control panel, in operator housing.

3.1.4 Do not install surface mounted items until substrates have been properly prepared and substrate finishes have been completed:3.1.4.1 Wash down masonry walls and complete painting and staining of doors and

frames prior to installation of hardware.3.1.4.2 Complete finish flooring at doorways.3.1.4.3 Where door or frame finishing is not practical prior to installation, remove

hardware prior to finishing door and frame.3.1.4.4 Wrap or mask exposed hardware that cannot be removed until date of

substantial completion to avoid exposure to paint, solvents, and abuse.

3.1.5 Correct conditions that inhibit a proper installation before continuing with work. If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.3.1.5.1 Do not proceed until unsatisfactory conditions have been corrected.

3.2 PREPARATION

3.2.1 Clean surfaces thoroughly prior to installation. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

3.3 HARDWARE LOCATIONS

3.3.1 Mount hardware units at heights indicated in the following publications except as specifically indicated or required to comply with the governing regulations including:3.3.1.1 Recommended Locations for Architectural Hardware for Standard Steel Doors

and Frames, by the Door and Hardware Institute (DHI).3.3.1.2 Recommended locations for Architectural Hardware for Flush Wood Doors (DHI)

and3.3.1.3 WDMA Industry Standard I.S. 1A - Interior Architectural Wood Flush Doors.3.3.1.4 WDMA Industry Standard I.S.-6A - Interior Architectural Stile and Rails Doors.

3.4 INSTALLATION

3.4.1 Install hardware in compliance with the DHI publication, Installation Guide for Doors and Hardware.3.4.1.1 Install each hardware item per manufacturer's instructions and

recommendations.3.4.1.2 Set units level, plumb and true to line and location.3.4.1.3 Adjust and reinforce substrates as necessary for proper installation and

operation.

3.4.2 Automatic Door Equipment: Installed by factory-trained installers in compliance with manufacturer's recommendations, ANSI/BHMA 156.10 and approved shop drawings.

3.4.3 Conform to local governing agency security ordinances and ICC/ANSI A117.1 Accessible and Usable Building and Facilities.

08 71 00-29

3.4.4 Connect door operators and access control devices to building services. Install and adjust sensors to detection field and functions required.3.4.4.1 Locate electric hinges at second hinge from bottom of frame.3.4.4.2 Termination: Ensure wiring is in place and is connected for proper operation of

hardware.

3.4.5 Fasteners:3.4.5.1 Install hardware using the manufacturers fasteners provided. Drill and tap screw

holes located in metallic materials. Do not use "Riv-Nuts" or similar products.3.4.5.2 Drill and countersink items not factory prepared for fasteners. Use only fasteners

furnished by manufacturer for installation as recommended by manufacturer.

3.4.6 Closers:3.4.6.1 Mount closers on room-side of corridor doors, inside of exterior doors, and stair-

side of stairway doors.3.4.6.2 Mount closers at clean rooms and operating rooms opposite room side to

eliminate shelf to collect dust and debris.3.4.6.3 Use necessary arms, brackets, spacers and plates to accommodate auxiliary

hardware and special applications.

3.4.7 Fire Door Assemblies: Maintain clearances at door edge to frame and meeting edge of pairs of doors in compliance with NFPA 80, providing 1/8 inch (3.175 mm) clearance at the hinge edge, lock edge, head and between pairs.

3.4.8 Undercuts:3.4.8.1 Maximum 3/4 inch (19 mm) undercut at door bottom. Coordinate with finished

flooring as required on both sides of each door.3.4.8.2 Where panic thresholds are used, undercut door to allow 1/8 inch (3.175 mm)

clearance between door and thresholds.

3.4.9 Thresholds:3.4.9.1 Trim, cut, and notch thresholds and saddles neatly to minimally fit door frame

profiles.3.4.9.2 Set thresholds in bed of mastic sealant, to form a tight seal between threshold

and setting surface.

3.4.10 Accessories:3.4.10.1 Install units complete with accessories in accordance with approved submittals

and manufacturer's recommendations.3.4.10.2 Install in proper relationship with adjacent construction. Separate dissimilar

metals with bituminous coating or other material acceptable to the Architect.3.4.10.3 Install blocking material for wall mounted door stops at height appropriate to

contact door trim. Install glazing in accordance with the project glazing specifications.

3.4.11 Install sealants in accordance with the project sealant specifications.

3.5 ADJUSTMENTS

3.5.1 Adjust door closer sweep periods so that from the open position of 70 degrees, the door will take at least 3 seconds to move to a point 3 inches (75 mm) from the latch, measured to the landing side of the door.

3.5.2 Lubricate bearings and adjust doors for proper operation, balance, clearance and similar requirements. Adjust door operators, controls, and hardware for operation and tightness.

3.5.3 Upon substantial completion, make final adjustments to door closers and other items of

08 71 00-30

hardware after final balance of heating and ventilating equipment to ensure doors close and latch properly.

3.6 FIELD QUALITY CONTROL

3.6.1 Verify doors open and close smoothly without rubbing or catching and have positive latching where scheduled. Verify fire rated doors are installed with clearances in compliance with NFPA 80.

3.6.2 Test electrified hold open devices tied into fire alarm system to confirm release upon activation of fire alarm. Test electrified hardware and access control to verify systems operate as directed in mode of operation. Where hardware is found to be inoperable, repair or replace with new.3.6.2.1 Inspect and approve automatic doors for compliance with ANSI/BHMA 156.10

prior to placing doors into operation by an AAADM certified technician.

3.6.3 Manufacturers Field Service: Provide periodic inspection and technical assistance as requested by the General Contractor.

3.6.4 Contractor/Installers, Field Services: After installation is complete, contractor to inspect completed door openings on site to verify installation of hardware is complete and properly adjusted, in accordance with both the Contract Documents and final shop drawings.3.6.4.1 Check and adjust closers to ensure proper operation.3.6.4.2 Check latchset, lockset, and exit devices are properly installed and adjusted to

ensure proper operation. Verify levers are free from binding. Ensure latchbolts and dead bolts are engaged into strike and hardware is functioning.

3.6.4.3 Report findings, in writing, to Architect indicating that hardware is installed and functioning properly. Include recommendations outlining corrective actions for improperly functioning hardware if required.

3.6.5 Repair or replace installed products damaged prior to or during installation and construction at least two weeks prior to date of Substantial Completion.

3.7 CLEANING

3.7.1 Clean and polish exposed hardware surfaces in accordance with manufacturer's recommended procedures. Clean or repair pencil or tool marks from adjacent surfaces damaged or soiled by work of this Section.

3.7.2 Comply with project's construction waste management program:3.7.2.1 Recycle cardboard boxes and paper products used in packaging and transport.3.7.2.2 Remove and legally dispose of remaining construction debris from project site.

3.8 PROTECTION

3.8.1 Protect installed products until completion of project. Prior to Substantial Completion:3.8.1.1 Remove temporary coverings and protection of adjacent work areas.3.8.1.2 Touch-up, repair or replace damaged products.

3.9 HARDWARE SCHEDULE

3.9.1 Hardware Schedule: Custom developed for each project.

END OF SECTION

08 71 00-31