008-skylar compliance & performance overview v3

Skylar Compliance and Performance Overview

THE SKYLAR PROJECT: FÁBRICA NETWORK 300 NEW TORONTO STREET, SUITE 3600, M8V 2E8 TORONTO, ONTARIO, CANADA TEL: +1 647 977 9176 or TEL: +1 888 788 8034, FAX: +1 888 588 1945 EMAIL: [email protected]

1

© The Skylar Project 2011. All rights Reserved NOTICE OF CONFIDENTIALITY This document including any information transmitted with it is intended only for the use of the addressees and is confidential. If you are not an intended recipient or responsible for delivering the message to an intended recipient, any review, disclosure, conversion to hard copy, dissemination, reproduction or other use of any part of this communication is strictly prohibited, as is the taking or omitting of any action in reliance upon this document. If you receive this document in error or without authorization please notify us immediately or otherwise and permanently delete the entire document from any computer, disk drive, or other storage medium.


2

International Building Code Compliance Fact Sheet

Overview

Provide modular building structures for residential and commercial applications that meet and exceed International Building Code compliance.

Description

Wall and roof systems designed from light gage steel, EPS and EFIS materials. All raw materials are accepted in regular building practices internationally. The unique fabrication process utilizes these products in a modular construction form. All fasteners meet or exceed building regulation internationally.

Exterior Material

• Exterior EFIS (cement like material) to meet and exceed international Building Code 2004

• Exterior EPS (Expanded Poly Styrene) to meet thermal performance values of R15 on average.

• Exterior IBS Roof System engineered and tested to meet any dead load requirements for the International Building Code 2004.

• Exterior Roof tile or shingle to meet International Building Code 2004. • Exterior windows and doors to meet or exceed energy compliance as well as air,

water and structural requirements. Low E coatings available to achieve higher U-‐Values.

Internal Material

• Internal EFIS and EPS material help achieve even higher thermal performance. Exceeds R15 with this option (performance up to R60 is also possible)

• Internal Drywall allows a minimum of 45 min fire rating where required. • Interior light gauge studs within EPS walls are a minimum of 18 gauge which

exceed International Building Regulations for exterior walls being 24 or even 26 gauge.

• All Steel members to be a minimum of galvanized or galvalume 90. This exceeds general building code which is generally galvalume 40 or less.

• All interior plumbing and electrical to be International Code Complaint.

Conclusion

All raw materials and fastening methods are derived from current accepted building code compliance products. Skylar building can be adapted to meet code in virtually any country.


3

Skylar Wall Panel Product Performance Test Test Method Criteria Results Air Leakage ASTM E 283 No Criteria 0.6l/min/m2 (0.002

cfm/ft2) Water Penetration ICC ES (AC 212)

ASTM E 331 No water penetration beyond the inner-most plane for the wall after 15 minutes at 137 Pa (2.86 Psf for drainage systems and after 2 hours at 300 Pa (6.24 Psf) for barrier systems

Passed

Drainage Efficiency ICC ES (AC 235)

ASTM E 2273 Minimum Drainage Efficiency of 90%

Passed

Accelerated Weathering

ASTM G 155 Cycle 1 ASTM G 154 Cycle 1 (QUV)

No deleterious effects after 2000 hours

No deleterious

Freeze Thaw (formerly EIMA 101.01)

ASTM E 2485 No deleterious effects after 60 cycles

Passed – No deleterious effects after 90 cycles

Impact Resistance (formerly EIMA Std. 101.86)

ASTM E 2486 No fracture of reinforcing mesh

Meets all requirements in each mesh category

Transverse Wind Load

ASTM E 330 Withstand positive and negative loads as specified by the building code

Minumum 4.3 kPa (90 Psf)* 16 inch o.c. framing, .5 in. sheathing screw attached at 203 mm (8 inch) o.c.

Fire Resistance ASTM E 119 NFPA 268

No effect of a rated wall assembly

Passed 1 hour

Intermediate Multi-story Fire Test

NFPA 285 (UBC 26-9) 1. Resist flame propagation over the exterior surface 2. Resist vertical spread of flame within combustible core/component of panel from one story to the next 3. Resist vertical spread of flame over the interior surface from one story to the next 4. Resist lateral spread of flame from the compartment of the fire of origin to the adjacent spaces

Passed

Full Scale Multi-Story (corner test)

ANSI FM 4880 Resist flame propagation over the exterior surface

Passed; No height restrictions for Outsulation of Outsulation Plus MD

Additional product performance information is available on request. Product performance may vary according to specific implementation, as building code and engineering specifications may call for additional criteria to be considered.

ENGLISH

EATON DONALDTHE SKYLAR PROJECT: FÁBRICA NETWORK

300 New Toronto Street, Suite 3600Toronto, Ontario, M8V 2E8TEL: +1 647 977 933 9090, FAX: +1 888 588 1945EMAIL: [email protected]

PORTUGUESE

MANUEL LIMATHE SKYLAR PROJECT: FÁBRICA NETWORK

300 New Toronto Street, Suite 3600Toronto, Ontario, M8V 2E8

TEL: +1 416 8915818 FAX: +1 888 588 1945

EMAIL: [email protected]

For more information, contact:

008-skylar compliance & performance overview v3

Documents