€¦ · 01| pneumatic cylinder reference data [1] - 2 mini pin cylinder / ajp [1] - 14 guide unit...
TRANSCRIPT
Pneumatic Cylinder01|
Reference Data [1] - 2
Mini Pin Cylinder / AJP [1] - 14
Guide Unit / KGUA [1] - 16
Small Pin Cylinder / ACP [1] - 18
Direct Mount Type Cylinder / ACD [1] - 26
Small Cylinder (AL Tube) / ACS2 [1] - 28
Small Cylinder (SUS Tube) / ACS3 [1] - 42
Small Cylinder (AL Tube/Air Cushion) / ACS4 [1] - 54
Small Cylinder (SUS Tube/Air Cushion) / ACS5 [1] - 58
Round Cylinder / ACR [1] - 62
Medium Cylinder / ACM [1] - 65
Large Cylinder / ACL [1] - 78
Extra-Large Cylinder / ACX [1] - 96
Low Friction Cylinder / KLC [1] - 100
Labyrinth Cylinder / KLCS [1] - 102
Compact Cylinder / AF, ADF [1] - 104
Compact Guide Cylinder / AFG [1] - 127
Free Mount Cylinder / FM, FMD [1] - 132
Custom-Made Rod Ends [1] - 135
Custom-Made Tie Rods [1] - 137
Booster Cylinder / KBP [1] - 138
Air-Hydro Converter / CCTS [1] - 142
KCC Co., Ltd.
www.kccpr.com21 -
PNEUMATIC & HYDRAULIC Pneumatic Reference Data
Pneumatic System
Adjust air flow rate.
Reduce exhaustion
noise
Change air flow direction
Move an object.
Rotary Cylinder
Speed Controller
Silencer
One-touch Joint
Tube
Air Gun
Air Solenoid ValveCylinderValveCylinder
ActuatorSpeed Control Valve
Suppliment Control Equipment(Directional control valve)
When using a pneumatic device, it is important to select and to apply every single device appropriately according to its applications. With reference to the following selection factors, select and design a suitable pneumatic system according to its applications.
Cylinder Selection
Item Select a pneumatic system regarding to kind of operation
Main factor What kind of operation
Sub factorControl
pneumatic circuit
Use pneumatic
tools
Control air ow
Control movement Others
Main equipment
Control equipment
Control equipment
Control equipment
Actuator,Control
equipment,Supplementary
equipment
-
Select a pneumatic system regarding toair quality
Quality of air
Lubricated type
Cleanliness
Regulator
Generator
Non-lubricated type
Cleanliness
Regulator
Generator
KCC Co., Ltd.
www.kccpr.com 31 -
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
PNEUMATIC & HYDRAULIC Pneumatic Reference Data
Pneumatic System
Adjusting Equipment Generator
What Is Air Pressure?There are different types of pressure unit, but International System of Units (SI units) is the most widely used unit. The absolute pressure is measured relative to the absolute zero pressure (the pressure that would occur at absolute vacuum). While gauge pressure is the pressure relative to the local atmospheric or ambient pressure. Gauge pressure kgf/cm2(bar) is used in this catalogue.
Absolute pressure = Gauge pressure + atmospheric pressure = Pressure indicated on pressure gauge + 1.033
1.033
1.013
14.7
760
0.101
1.0330
0 5
0 50
0
0
0
100
5
5
5
0.5
5000
9.8
9.7
0.98
10
142
7356
10
11.033
Negative pressure(Vacuum)(Unit)
Highpressure
Positive pressure
kgf/cm2
kgf/cm2
abs
MPa
mmHg
atm
bar
Psi
Absolute Pressure
Gravitation System of Units
OtherSystem of Units
InternationalSystem of Units
Gravitation System of Units
KCC Co., Ltd.
www.kccpr.com41 -
PNEUMATIC & HYDRAULIC Pneumatic Reference Data
Theoritical Output
Relation Between Cylinder Output & Pressure
Cylinder output force can be found by knowing tube's bore size, piston rod diameter and air pressure. In general, pressure coef cient is depending on sliding resistance of cylinder packing and friction resistance of metal rod. But the load factor of theoritical output is set 0.7 or less generally.In case of fast speed is required, load factor of theoritical output should be set as 0.5 or less. Following is the formula of theoritical force.
F1 : Extension theoritical force (kgf)
F2 : Retraction theoritical force (kgf)
P : Working pressure (kgf/cm2)
D : Bore size (cm)
d : Piston rod diameter (cm)
1 : Friction coef cient (Extension)
2 : Friction coef cient (Retraction)
W1 : Extension cylinder output (kgf)
W2 : Retraction cylinder output (kgf)
Friction Coef cient
0.75Ø40
Ø50
Ø80
Ø63
Ø100이상
F1 = × D2 × P4
F2 = × (D2 - d2) × P4
W1 = 1 × F1
W2 = 2 × F2
Pressure
Pressure
Fric
tion
Coe
f ci
ent
Wei
ght-P
ress
ure
Coe
f ci
ent
& above
KCC Co., Ltd.
www.kccpr.com 51 -
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
PNEUMATIC & HYDRAULIC Pneumatic Reference Data
Theoritical Output
Bore size (mm)
Rod dia.(mm)
Operating direction
Pressurized area
Working pressure (kgf/cm2)
2 3 4 5 6 7 8 9 10
6 3 OUT 0.283 0.57 0.85 1.13 1.41 1.70 1.98 - - -IN 0.212 0.42 0.64 0.85 1.06 1.27 1.48 - - -
10 5 OUT 0.785 1.57 2.36 3.14 3.93 4.71 5.50 - - -IN 0.589 1.18 1.77 2.36 2.95 3.53 4.12 - - -
15 6 OUT 1.767 3.53 5.30 7.7 8.84 10.60 12.37 - - -IN 1.484 2.97 4.45 5.94 7.42 8.91 10.39 - - -
16 5 OUT 2.01 4.02 6.03 8.04 10.1 12.1 14.1 - - -IN 1.81 3.62 5.43 7.24 9.05 10.9 12.7 - - -
20 10 OUT 3.14 6.28 9.42 12.57 15.71 18.85 22.0 15.1 28.3 31.4IN 2.36 4.71 7.07 9.42 11.78 14.14 16.49 18.85 21.2 23.6
25 12 OUT 4.91 9.82 14.73 19.693 24.5 29.4 34.4 39.3 44.2 49.1IN 3.78 7.56 11.33 15.11 18.89 22.7 26.4 30.2 34.0 37.8
30 12 OUT 7.07 14.14 21.2 28.3 35.3 42.4 49.5 56.5 63.6 70.7IN 5.94 11.88 17.81 23.8 29.7 35.6 41.6 47.5 53.4 59.4
32 12 OUT 8.04 16.6 24.1 32.2 40.2 48.3 56.3 64.3 72.4 80.4IN 6.91 13.8 20.7 27.6 34.6 41.5 48.4 55.3 62.2 69.1
40 16 OUT 12.57 25.1 37.7 50.3 62.8 75.4 88.0 101 113.1 125.7IN 10.56 21.1 31.7 42.2 52.8 63.3 73.9 84.4 95.0 105.6
50 20 OUT 19.63 38.3 58.9 78.5 98.2 117.8 137.4 157.1 176.7 196.3IN 16.49 33.0 49.5 66.0 82.5 99.0 115.5 131.9 147.4 146.9
63 20 OUT 31.2 62.3 93.5 124.7 155.9 187.0 218 249 281 312IN 28.0 56.1 84.1 112.1 140.2 168.2 196.2 224 252 280
80 25 OUT 50.3 100.5 150.8 201 251 302 352 402 452 503IN 48.5 90.7 136.1 181.4 227 272 317 363 408 454
100 30 OUT 78.5 157.1 236 314 393 471 550 628 707 785IN 71.5 142.9 214 286 357 429 500 572 643 715
125 35 OUT 122.7 245 368 491 615 736 859 982 1104 1227IN 112.5 225 338 450 563 675 788 900 1013 1125
140 35 OUT 153.9 308 462 616 770 924 1078 1232 1385 1539IN 143.8 288 431 575 719 863 1006 1150 1294 1438
150 40 OUT 176.7 353 530 706 883 1060 1236 1413 1590 1767IN 167.1 334 501 668 835 1002 1169 1336 1503 1671
160 40 OUT 201 402 603 804 1005 1206 1407 1608 1810 2011IN 188.5 377 565 754 942 1131 1319 1508 1696 1885
180 45 OUT 254 509 736 1018 1272 1527 1781 2036 2290 2545IN 239 477 716 954 1193 1431 1670 1909 2147 2396
200 50 OUT 314 628 942 1257 1571 1885 2199 2513 2827 3142IN 295 589 884 1178 1473 1767 2062 2356 2651 2945
250 60 OUT 491 982 1473 1963 2454 2945 3436 3927 4418 4909IN 463 925 1388 1850 2313 2776 3238 3701 4163 4626
280 70 OUT 615.4 1230.8 1846.2 2461.6 3077 3692.4 4307.8 4923.2 5538.6 6154IN 576.9 1153.8 1730.7 2307.6 2884.5 3461.4 4038.3 4615.2 5192.1 7569
300 70 (75)OUT 707 1414 2121 2827 3534 4241 4948 5655 6362 7069IN 668
(662.3)1337
(1324.6)2005
(1986.9)2673
(2649.2)3342
(3311.5)4040
(3972.8)4679
(4636.1)5347
(5298.4)6015
(5960.7)6684
(6623)350 85 OUT 961.6 1923.2 2884.8 3846.4 4808 5769.6 6731.2 7692.8 8654.4 9619
IN 904.9 1809.8 2714.7 3619.4 4524.5 5429.4 6334.3 7239.2 8144.1 9049400 100 OUT 1256 2512 3768 5024 6280 7536 8792 10048 11304 12560
IN 1177.5 2355 3532.5 4710 5887.5 7065 8242.5 9420 10597.5 11775450 100 OUT 1589.6 3179.2 4768.8 6358.4 7948 9537.6 11127.2 12716.8 14306.4 15896
IN 1494.6 2989.2 4483.8 5978.4 7473 8967.6 10462.2 11956.8 13451.4 14946
Double Acting Cylinder
Bore size (mm)
Rod dia.(mm)
Operating direction
Pressurized area
Working pressure (kgf/cm2)
2 3 4 5 6 7 8 9 10
2.5 1 OUT 0.049 - 0.03 0.08 0.13 0.174 0.223 - - -IN - 0.06
4 2 OUT 0.126 - 0.10 0.22 0.35 0.47 0.60 - - -IN - 0.15
6 3 OUT 0.283 0.17 0.45 0.73 1.0 1.3 1.6 - - -IN - 0.15
10 4 OUT 0.785 0.94 1.7 2.5 3.3 4.1 4.9 - - -IN - 0.25
15 5 OUT 1.767 2.1 3.9 5.7 7.4 9.2 11.0 - - -IN - 0.45
16 5 OUT 2.01 2.6 4.61 6.62 8.68 106 12.7 - - -IN - 0.7
20 10 OUT 3.14 2.1 5.2 8.4 12 15 18 21 24 27IN - 0.9
25 12 OUT 4.91 4.5 9.4 14 19 24 29 34 39 44IN - 1.0
30 12 OUT 7.07 6.6 14 21 28 35 42 49 56 63IN - 1.5
40 18 OUT 12.57 16 29 42 54 67 79 92 104 117IN - 2.0
Single Acting Cylinder (Spring Return)
Theoritical force of a single acting cylinder during extension is the value of theoritical force of double acting cylinder subtract spring tension. While theoritical force of single acting cylinder during retraction is the value of spring tension.
Do not apply load to piston rod during retraction.
KCC Co., Ltd.
www.kccpr.com61 -
PNEUMATIC & HYDRAULIC Pneumatic Reference Data
Air Consumption
Air Consumption Calculation
Air consumption can be found by knowing the volume of cylinder and piping volume between cylinder and valve.
How to Read Graph
Tube volume is varies depending on the ways of piping. Therefore, only cylinder air consumption is calculated.
Air Consumption of Cylinder & Tube
Q = (A1 + A2)L × (P + 1.033)N1000
Q: Air consumption ( /min)P: Working pressure (kgf/cm2)L: Stroke (cm)N: Number of reciprocation per min
A2 = (D2 -d2)4
A2: Rod side piston aread: Rod diameter(cm)
A1 = × D2
4
A1: Head side piston areaD: Tube bore size(cm)
How to read graph
Cylinder air consumption N /min
Example
Cylinder stroke x Number of reciprocation per minute (mm/min) orLength of tube x Number of piston reciprocation per minute.
Example
Working pressure kgf/cm2
Tube
bor
e si
ze
mm
Tube
type
Working pressure kgf/cm2
Example
For cylinder bore size is 40mm, stroke is 100mm, working pressure is 5kgf/cm2, number of piston reciprocation per minute is 5. Cylinder air consumption = Cylinder stroke x Number of piston reciprocation per minute. = 100 × 5 = 500 mm/min or 8N /min Example
For cylinder bore size is 40mm, stroke is 100mm, working pressure is 5kgf/cm2, number of piston reciprocation per minute is 5, and cylinder is connected to a 6mm-diameter nylon tube with 2m length.Cylinder air consumption = length of tube x Number of piston reciprocation per minute. = 2000 × 5 = 1000 mm/min or 3N /min
KCC Co., Ltd.
www.kccpr.com 71 -
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
PNEUMATIC & HYDRAULIC Pneumatic Reference Data
Symbol
SymbolSymbol Type Remarks
Flow line
Line connection
Distance between lines of shafts or lever rod.
Energy conversion unit, Pump, Compressor,
Motor
Measuring devices
Rotating joint of check valve
Link joint roller
Valve
L > 10EL > 5EL : Line length E : Line weigth
d : Diameter of black dotE : Line weight
Symbol Type Remarks
Flow directionFlow inlet port or
exhaust port
Black triangle indicates liquid state fluid, while white triangle indicates
gas state fluid.
Indication of flow direction
Indication of rotation
Filter, separator, lubricator, heat
exchanger
Assembly unit
Indication of the possibility of adjustment
Symbol Type Remarks Symbol Type Remarks
Single acting cylinder
without spring
Double acting cylinder
single rod
Single acting cylinder
without spring
Double acting cylinder
double rod
Single adjustable
cushion cylinder
Double adjustable
cushion cylinder
(1) Detail symbol(2) Simplified symbol
(1) Detail symbol(2) Simplified symbol
(1) Detail symbol(2) Simplified symbol
(1) Detail symbol(2) Simplified symbol
indicate adjustable type
Differential cylinder
Telescopic cylindersingle acting
Double acting
Diaphragm type cylinder
Pressure converter(Same fluid)
Pressure transmitters
Ram cylinder
Pressure converter(Different fluid)
KS B 0054-82, JIS B 0125-1972
(1)
(2)
(1)
(2)
(1)
(2)
(1)
(2)
(1)
(2)
(1)
(2)
(1)
(2)
(1)
(1)
(2)
(2)
(3)
Size of those circles are differentiate in large, medium and small in
drawing diagram.
KCC Co., Ltd.
www.kccpr.com81 -
PNEUMATIC & HYDRAULIC Pneumatic Reference Data
Pneumatic Cylinder
Structure Classi cation
Type Features
Mounting Style Classi cation
Single Acting Cylinder(Single rod)
Single Acting Cylinder(Double rod)
Double Acting Cylinder(Single rod)
Double Acting Cylinder(Double rod)
Stroke Adjustable Cylinder
Dual Stroke Cylinder(Single rod)
Dual Stroke Cylinder(Double rod)
Tandem Cylinder
Cylinder in which the air acts on one side of the piston only, normally piston is returned by spring force or weight.
Cylinder which the working fluid acts alternately on both sides of the piston. It is a most common type cylinder.
Cylinder with a variable stopper to adjust stroke.
Cylinder with 2 strokes. It has the same function as adjusting 2 cylinders.
Cylinder with multiple pistons. Tandem cylinder with "N" pistons produces "N" times force.
Standard Type (B)
Foot Type (LB)
Flange Type(FA, FB)
Cylinder without any mounting bracket.
Foot bracket attached cylinder, which moves load in horizontal direction.
Flange bracket attached cylinder, which moves load in vertical direction.
Rod side flange(FA)
Head side flange (FB)
KCC Co., Ltd.
www.kccpr.com 91 -
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
PNEUMATIC & HYDRAULIC
Type Features
Pneumatic Reference Data
Pneumatic Cylinder
Clevis Type(CA, CB)
Trunnion Type (TC)
Cylinder with a pin hole at the right angle direction of rod centerline. Cylinder with single clevis mount or double clevis mount with allow rotation.
Cylinder with a pin at the right angle direction of rod centerline. Cylinder with pin at the middle is called center trunnion type cylinder. The cylinder allows angular movement.
Note) Figures inside "( )" indicates KS Standard classi cations.
Pneumatic Cylinder Parts
Piston : It should be strong, abrasion resistance and seizure resistance. Generally, grey cast iron material is used for its excellent slide characteristics.
When light weight is required, plastic or AL alloy wearing is used.
Piston rod : Alloy steel S45C or above class is used, plated by hard Cr, with a surface roughness of 1.6S, wear resistance and abrasion resistance.
Buckling and bending should be considered when design process is carry on.
Cylinder tube : To prevent wear of inner tube, it required 20 hard plating or hard coating and 1.6S of surface roughness.
Cover : Part for rod bush and sealing packing is attached as well as the air port size adjusting part.
Tie rod : Fix both of the cover(head side cover and rod side cover)
Rod bush : Lateral load applied on piston rod is supported by rod bush and lateral load must be within 1/20 of max. cylinder output.
SEAL :
1) Fixing type : O-Ring (NBR)
2) Moving type : Squeeze packing, moving o-ring, lip packing, wiper ring, dust seal and etc.
Squeeze packing: When pressue is applied, the expansion force of the paking form a contact pressure to seal.
Lip packing: When pressue is applied onto the lip(bending part) and make the bending lip become straight and contact to the inner tube
surface to seal.
Single Clevis (CA)
Double Clevis (CB)
Center Trunnion(TC)
KCC Co., Ltd.
www.kccpr.com101 -
PNEUMATIC & HYDRAULIC
Work piece feeding
Snap-ring fastening
Cylinder
Feeding
Auto open/close Press
Direction change Return
Gate open/close Assembly
Cylinder
Workpiece
Cylinder
Pneumatic Reference Data
Application of Pneumatic Cylinder
Applications
KCC Co., Ltd.
www.kccpr.com 111 -
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
PNEUMATIC & HYDRAULIC Pneumatic Reference Data
Precautions
LB, FA, FB MountUse washer when fastening bolt to cylinder to prevent loosening.
Do not apply any unnessary load to mount and avoid improper installation.
Do not apply eccentric load or lateral load to cylinder rod.
LB Mount
CA, CB, TC Mount (Angular Movement)For stroke 1000mm or above, horizontal installation is not recommended.
TC Mount
Load
Load
Load
Load
Retraction with load
Extension with load
FA
FA
FB
FB
KCC Co., Ltd.
www.kccpr.com121 -
PNEUMATIC & HYDRAULIC
Precautions
Pneumatic Reference Data
1. Do not hit or apply excessive impacts on to cylinder.
2. Flush (with air) or wash to remove chips, cutting oil and other debris from pipe before piping is connected.
3. Be certain to align the rod axis with the load and direction of movement when connecting.
(When it is necessary, use a oating joint to prevent eccentric)
Notes on Installation
Notes on Use 1. Check the puri cation system regulary to ensure clean uid is used.
2. Use Turbine oil class 1(ISO VG32) for lubricated type cylinder.
3. Do not discontinue to lubricate once if you lubricate it.
4. Do not scratch or gouge the sliding parts of the cylinder tube or piston rod. (May lead to seal damage and cause air leakage)
5. Install a special device to protect rod if the cylinder is using under a poor conditions (which is full with dust or spark)
Notes on Maintenance 1. Check cylinder mounting nut and bolt from become loose.
2. Check mounting bracket of cylinder from getting loose or etc.
3. Check cylinder operating condition.
4. Check the change of speed of cylinder with time.
5. Check air leakage and scratch on rod surface.
6. Check rod end accessory, tie rod or bolt from getting loose.
In uences of Foreign Substaince 1. Clog of path of lter element cause pressure drop.
2. Weaken the exhaustion performance of lter drain.
3. Cumulative foreign substaince on ow path decrease ow rate.
4. Cumulative foreign substainceon operating part can cause malfunction.
5. Corrosion can cause malfunction.
6. Exceeded friction can cause damage to seal and diaphragm.
7. Malfunction of solenoid valve
KCC Co., Ltd.
www.kccpr.com 131 -
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
PNEUMATIC & HYDRAULIC
Cause s & Resolve of Trouble
Pneumatic Reference Data
Even though seal material, surface treatment, electrical material, electronics technology has been remarkably improved and product have a longer service life with higher reliability and less failure rate compare with conventional product. However, constant occurrence of trouble is still considerable.
Pneumatic is easy to handle and maintenance. However, without understanding of the nature of compressibility characteristic of air as a working uid in pneumatic system might cause an unexpected accident.
Different kinds of trouble examples of following pneumatic devices are shown below Pneumatic cylinder, Air hydro cylinder, Rotary actuator, Pressure transmitter Solenoid valve, Speed controller, Reducing valve, Auto switch Air generator, Air compressor, Compressed air quality Lubrication, Safety
Explain the trouble which happen commonly and explain the causes and resolves by giving examples, so that it is easy to be understood even for a beginner.
Among pneumatic devices, trouble mostly happen on pneumatic cylinder and solenoid valve. Following are the details about cylinder and solenoid trouble.
(1) Air Source (Air Compressor)Lack of air suppy is a common trouble for air generator. Therefore, select an air compressor with suitable air capacity and select an air tank or change the pipe size might solve the problem.
The degradation of air compressor, after cooler performance and other devices or re accident can be prevented by having maintenance regularly.
(2) PipingImproper piping method can cause critical pressure drop or draining. Mixing of chips, cutting oil and other debris can also cause a problem.
To prevent these troubles from happening for better durability, it is assential that user has to learn a proper piping technic and connect the pipe carefully.
(3) Air quality and LubricationDuring air compression, drain problem can not be avoided. Thus, a countermeasure is necessary. Auto drain, air dryer and other devices are used to prevent freezing.Regarding lubrication oil. Improper handing of lubricator or fault maintenance can cause lubrication insuf ciency problem. Learing lubricating technic, applying non lubricated combination can increase service life and rust resistance.
(4) Pneumatic CylinderInadequate pneumatic circuit might cause risk such as cylinder runaway or can not do emergency stop (because of air pressure compressibility). For those trouble, user should have a deep understanding about the relation between load factor of pneumatic cylinder and its operation. Besides, there are other troubles such as piston rod damage or packing damage. These troubles can be avoided by appropriate pneumatic circuit design, usage and installation.
(5) Solenoid ValvePilot type solenoid valve common troubles: insuf cient pilot pressure, malfunction caused by control valve.Direct acting type solenoid valve common troubles: Coil burnout accident caused by inproper spool operationSolenoid has a lot of trouble when associated with methods or environments such as wiring, rain water, temperature and etc.
(6) Notes on safetyInadequate pneumatic circuit might cause risk such as cylinder runaway or emergency stop failure (due to air pressure compressibility)
Thus, application of a proper pneumatic circuit is essential to prevent accident like dropping of workpiece or hand injured by machine when electricity cut off occur.
KCC Co., Ltd.
www.kccpr.com 141 -
PNEUMATIC & HYDRAULIC
Mini Pin Cylinder
AJP series
AJP series
AJP - B 10 - 15 -
Bore size6 6mm
10 10mm15 15mm
Hose nipple (Option)Nil None (Standard)H4 For tube Ø4-2.5 H6 For tube Ø6-4
Rod end threadNil With threadB Without thread
Cylinder stroke5 5mm
10 10mm15 15mm
Unit :N
Bore size Stroke (mm) 0 Stroke Stroke end
Ø6 5, 10, 15 3.92 1.47
Ø10 5, 10, 15 5.98 2.45
Ø15 5, 10, 15 10.79 4.41
Same spring force for all stroke.
Applicable tube size Model
Ø4-2.5 N4M5
Ø6-4 N6M5
Unit :g
ModelStroke (mm)
5 10 15
AJP-B6 10.6 13.1 15.6
AJP-B10 28 33 38
AJP-B15 72 82 92
How to Order
Speci cations
Spring Retracting Force
Mass
Hose Nipple For Panel Mount Style
SeriesAJP Mini pin cylinder
Features
Short-stroke cylinder designed with a shorter overall length than a conventional cylinder. Space saving pin cylinder for
panel mounting. It miniaturizes the size of mechanical devices.
Symbol
Single Acting /Spring Return
Weight of hose nipple (4g) is not included.
Action Single acting spring return
Fluid Air
Proof pressure 10.5kgf/cm2 (1.05MPa)
Max. operating pressure 7kgf/cm2 (0.7MPa)
Min. operating pressure
Ø6 2kgf/cm2 (0.2MPa)Ø10, Ø15 1.5kgf/cm2 (0.15MPa)
Ambient & fluid temperature 5 ~ 60
Operating piston speed 50~500mm/s
Cushion None
Lubrication Not required
Tolerance of stroke +1.00
Tolerance of thread KS class 2
Mounting style Panel mounting
Accessory Mounting nut 2 pcsRod end nut 2 pcs (Rod end thread type)
KCC Co., Ltd.
www.kccpr.com 151 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Mini Pin Cylinder
AJP series
Unit : mm
Bore size A B C EF
ØG H K MM NN RS
WZ
ØQ5ST 10ST 15ST 5ST 10ST 15ST 5ST 10ST 15ST
Ø6 7 12 13.9 6 12.5 19.5 26.5 8.5 9 3.5 M3X0.5 M10X1.0 9 18.5 25.5 32.5 3 27.5 34.5 41.5 3
Ø10 10 19 22 6 14.5 21 28 12 12 3.5 M4X0.7 M15X1.5 13 20.5 27 34 4 32.5 39 46 5
Ø15 12 27 31 7 16.5 22.5 29 19 14 4.2 M5X0.8 M22X1.5 20 23.5 29.5 36 5 37.5 43.5 50 6
Part no. Parts Material Remark
1 Cover Brass Electroless Nikel Plating
2 Piston Stainless Steel -
3 Collar Sintered Metal Bronze
4 Return Spring Steel Wire Zinc Chromate
5 Piston Packing NBR -
6 Mounting Nut Brass Electroless Nikel Plating
7 Rod End Nut Steel Nikel Plating
Unit : mm
Part no. Applicable bore size d H B C
AJP-SN06 Ø6 M10×1.0 3 12 13.9
AJP-SN10 Ø10 M15×1.5 4 19 22AJP-SN15 Ø15 M22×1.5 5 27 31
Unit : mm
Part no. Applicable bore size d H B C
AJP-RN06 Ø6 M3×0.5 1.8 5.5 6.4
AJP-RN10 Ø10 M4×0.7 2.4 7 8.1AJP-RN15 Ø15 M5×0.8 3.2 8 9.2
Dimensions
Structure Dimensions-Accessory
7
36 1 4 2
5
d
B
C
H
d
B
C
H
H
ØQ
Ø6: C0.5Ø10,15: C1
B
R
C
M5×0.8
ØG
MM
A
H
Z
W
S
F E
NN
Mounting Nut
Rod End Nut
Material: Brass
Material: Carbon Steel
Rod end without thread.
KCC Co., Ltd.
161 -
PNEUMATIC & HYDRAULIC
www.kccpr.com
Guide Unit
KGUA series
KGUA series
KGUA 20 - 100
SeriesKGUA Guide unit for cylinder
Bore size of applicable cylinder10 Ø1016 Ø1620 Ø2025 Ø2532 Ø3240 Ø40
How to Order
KGUA 20-100
Cylinder not included.
Cylinder strokeBore size Standard stroke
Ø10 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 75, 100, 125, 150
Ø16 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 75, 100, 125, 150, 175, 200
Ø20 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450,
500, 550, 600Ø25
Ø32
Ø40 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600
Other intermediate strokes available on request.
MassUnit : kg
Bore size (mm) Ø10 Ø16 Ø20 Ø25 Ø32 Ø40
Basic mass 0.17 0.26 0.33 0.59 0.64 1.24Additional mass of each 50mm stroke 0.06 0.09 0.16 0.25 0.26 0.41
Features
Smooth and precise movement. Excellent appearance and easy to mount. Can be combined with various cylinders. Adoption of advanced material in non-
lubricated bearing
1. Care must be taken to avoid injuries or damage arising from an object being crushed or pressed against the sliding part on the guide rod.2. The surface of the guide rod is made with a high degree of precision, therefore a slight deformation or scar may cause malfunction or impaired durability.3. If a guide body is tted, the tting surface thereof should have a high degree of atness.4. A distorted or bent guide rod may cause abnormal increase in operational resistance and early wear on the bearing, resulting in impaired performance.5. Fit on the place in contemplation of easy maintenance. Secure suf cient space around the cylinder for easy maintenance.6. Do not move the back plate to adjust strokes. It may cause poor impact absorption when the back plate comes in contact with the guide body or the bolt xing the bracket, resulting in improper stroke positions and operation.
Precautions
Calculation:
Ex) KGUA 32-500 Basic mass: 0.64(32Ø) / Additional mass: 0.26/50 / Stroke: 500mm 0.64+(0.26/50X500) = 3.24kg
KCC Co., Ltd.
171 -
PNEUMATIC & HYDRAULIC
www.kccpr.com
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Guide Unit
KGUA series
Part no. Parts Material
1 Guide Body Aluminium Alloy
2 DU Bush -
3 Guide Rod Steel
4 Back Plate Aluminium Alloy
5 Front Plate Steel
6 Bolt For Guide Carbon Tool Steel
7 Flat Washer -
8 Rod End Attachment Carbon Steel
Structure
1 2 3
4
5
6
7
8
Unit : mm
Model A B C D1 D2 E1 E2 F1 F2 G H1 H2 H3 H4 I1 I2 J K
KGUA10 53 17 50 10 3 51 26 16 16 39 Ø8 Ø14 Ø8 Ø12 12 25 25 Ø6
KGUA16 66 22 50 10 3 64 32 20 22 48 Ø10 Ø20 Ø8 Ø12 12 30 32 Ø8
KGUA20 80 32 80 10 7 78 40 30 30 60 Ø20 Ø29 Ø14 Ø22 25 38 40 Ø10
KGUA25 100 40 90 10 7 98 60 38 40 76 Ø26 Ø34 Ø14 Ø22 29 50 52 Ø10
KGUA32 100 44 90 12 9 98 60 40 40 76 Ø26 Ø40.5 Ø14 Ø22 35 50 52 Ø12
KGUA40 126 54 120 12 9 124 70 50 50 100 Ø32 Ø50.5 Ø21 Ø26 44 68 74 Ø14
Model L2 L1 M N P Q R1 R2 R3 S T U V W X Y Z
KGUA10 13 24 12 18 9 10 14 20 R9 150+Stroke Ø5.5 M3DP5 Ø9DP6.5 M3 5 17 14
KGUA16 13 24 16 22 15 14 14 20 R11 150+Stroke Ø5.5 M4DP8 Ø9DP6.5 M3 5 17 14
KGUA20 15 50 22 32 18 22 25 35 R16 106+Stroke Ø8 M4DP8 M5DP8 M4 5 15 35
KGUA25 20 50 30 36 28 30 25 35 R18 119+Stroke Ø8 M4DP10 M5DP10 M4 5 15 45
KGUA32 20 50 30 40 28 30 25 35 R20 123+Stroke Ø9 M4DP12 M5DP12 M5 5 15 45
KGUA40 25 70 38 55 38 40 26 43 R27.5 150+Stroke Ø10 M4DP15 M5DP16 M6 8 20 66
Dimensions
Q
4-U
2-V
4-W
KCC Co., Ltd.
www.kccpr.com181 -
PNEUMATIC & HYDRAULIC
Small Pin Cylinder
ACP series
ACP series
ACP - B 16 - S 30
Mounting styleB Standard
LB FootFA FlangeCB Double clevis (Except Ø6)
Bore size6 6mm
10 10mm16 16mm
Head cover positionØ6 Ø10, Ø16
Nil Axial (Standard) 90 from axialR - Axial
Not available for double rod and CB mounting type.
ActionNil Double actingS Single acting spring returnT Single acting spring extend
Not available for double rod type.
Auto switchReed A/S Model Solid State A/S Model
Nil None Nil NoneC72 D-C72K H7A1 D-H7A1KC73 D-C73K H7A2 D-H7A2KC76 D-C76K H7B D-H7BKC80 D-C80K
Refer to Auto Switch Catalogue for more information.
Cylinder strokeAction
Bore size Double acting Double rod Single rod
Ø65, 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 75,
100
- 15, 30, 45, 60
Ø105, 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 75, 100, 125, 150
15, 30, 45, 60 15, 30, 45, 60
Ø16
5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 75, 100, 125, 150,
175, 200
15, 30, 45, 60 15, 30, 45, 60
Number of auto switchesNil 2 pcs1 1 pcN N pcs (N: 3, 4, 5...)
Only for auto switch attached type.
SeriesACP Single rod small pin cylinder
ACPW Double rod small pin cylinder
How to Order
Symbol
Double Acting /Single Rod
Single Acting /Spring Return
Double Acting /Double Rod
Single Acting /Spring Extend
Features
Build-in magnet (Standard) Easy to install with its compact size. Piston rod with small de ection.
AccessoryNil Rod end nut (Standard) :2 pcI Single knuckle jointY Double knuckle joint
Refer to page [1]-133, for specifications about custom-made rod ends.
KCC Co., Ltd.
www.kccpr.com 191 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
ACP seriesSmall Pin Cylinder
Mounting style Standard Foot Flange Double Clevis
Standard mounting
Mounting nut -
Rod end nut
Clevis pin - - -
Option
Single knuckle joint
Double knuckle joint
For double clevis and double knuckle joint, pin and snap ring are included. Double clevis is not applicable to double rod type.
MountingBore size
Ø6 Ø10 Ø16
Foot mounting ACP B6-LB ACP B10-LB ACP B16-LB
Flange mounting ACP B6-FA ACP B10-FA ACP B16-FA
Bore size Begining of return End of return
Ø6 3.72 1.77
Ø10 6.86 3.53
Ø16 14.2 6.86
Mounting Style & Option
Mounting
Position of Port on Head Cover
Spring Return Force
For standard type, position of head cover port is on axial direction or perpendicular to axial direction. But, Ø6 type only availabe on axial direction.
Unit : g
Bore size (mm)Double Acting
Single RodDouble Acting Double Rod
Ø6 Ø10 Ø16 Ø6 Ø10 Ø16Basic mass 15 24 55 27 35 70
Additional mass for each 15mm stroke 2 4 6.5 3 6 9
Mounting mass
Foot 8 8 20 16 16 40
Flange 5 5 15 5 5 15Double clevis
(with pin) - 4 10 - - -
Accessory
Single knuckle joint - 16 24 - - -
Double knuckle joint (with pin) - 24 22 - - -
Bore sizeSpring return
(Forward)Spring extend
(Reverse)Ø6 Ø10 Ø16 Ø6 Ø10 Ø16
Basic mass
15 Stroke 11 28 63 17 28 64
30 Stroke 16 35 80 21 34 80
45 Stroke 18 44 102 23 43 100
60 Stroke 23 53 124 27 51 121
75 Stroke - - 145 - - 140
100 Stroke - - 188 - - 178
125 Stroke - - 224 - - 212
150 Stroke - - 250 - - 236
Basic mass does include the mass of mounting nut and rod end nut. Mass of double clevis does not include the mass of mounting nut.
Mass
1. Standard type Ex) ACP-LB10-S45
Basic mass: 24(Ø10) / Additional mass: 4/15 Cylinder stroke: 45mm Mass of mounting: 8(Axial foot type) 24+(4/15×45)+8=44g
2. Single acting spring return type Ex) ACP-LB10-S45T
Basic mass: 43(Ø10, 45 Stroke) / Mas of mounting: 8(Axial foot type) 43+8=51g
Calculation:
Axial direction 90 from axial
Bore sizeAccessory Ø10 Ø16
Single knuckle joint ACP B10-I ACP B16-I
Double knuckle joint ACP B10-Y ACP B16-Y
Accessory
Speci cations
Action Double acting, Single rod Double acting, Double rod Single acting, Spring return Single acting, Spring extend
Fluid Air
Proof pressure 10.5kgf/cm2 (1.05MPa)
Max. operating pressure 7.0kgf/cm2 (700kPa)
Min. operating pressureØ6 1.2kgf/cm2 (120kPa) 1.5kgf/cm2 (150kPa) 2.0kgf/cm2 (200kPa) 2.5kgf/cm2 (250kPa)
Ø10, Ø16 0.6kgf/cm2 (60kPa) 1kgf/cm2 (100kPa) 1.5kgf/cm2 (150kPa)
Ambiet & fluid temperature 5 ~ 60
Operating piston speed 50 ~ 750mm/sec
Cushion Rubber bumper
Lubrication Not required
Tolerance of thread KS class 2
Tolerance of stroke +1.00
KCC Co., Ltd.
www.kccpr.com201 -
PNEUMATIC & HYDRAULICKCC Co., Ltd.
ACP seriesSmall Pin Cylinder
Part no. Parts Material
1 Rod Cover AL
2 Head Cover AL
3 Cylinde Tube SUS
4 Piston Rod SUS
5 Piston MBSBE
6 O-Ring NBR
7 Piston Packing NBR
8 Rod Packing NBR
Part no. Parts Material
9 Guide Packing NBR
10 Damper Urethane
11 Magnet Nd-Fe-B
12 Mounting Nut MBSBE
13 Rod End Nut -
14 Packing Retainer AL
15 Spring Guide AL
16 Spring -
Structure
2710318
2
12413 14 119 513 4 12 8 1 9 3 10 5117 6 2
Double Acting, Single RodØ6
Double Acting, Single RodØ10, Ø16
Single Acting Spring Return
Double Acting, Double Rod
Single Acting Spring Extend
13 1 234 5 97 6101112 16 15 13 4 12 210 3 16155791 611
13 4 12 8 1 9 3 10 5117 6 1 4128 13
KCC Co., Ltd.
www.kccpr.com 211 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTSUnit : mm
Bore size A ØD H KK L ØLC LH LT LX LZ M PA PB T TL WA WB X Y
Ø6 15 3 8 M3X0.5 49 4.5 9 1.6 24 32 M6XP1.0 14.5 - 28 77 16 7 7 5
Ø10 15 4 8 M4X0.7 46 4.5 9 1.6 24 32 M8XP1.0 8 5 28 74 12.5 9.5 7 5
Ø16 15 5 8 M5X0.8 47 5.5 14 2.3 33 42 M10XP1.0 8 5 28 75 12.5 9.5 9 5
Dimensions-Double Acting/Foot (LB)
Ø6
Ø10, Ø16
Dimensions-Double Acting/Standard (B)
Unit : mm
Bore size A ØC ØD H KK L M ØNDh8 PA PB T TL VA WA WB
Ø6 15 14 3 8 M3X0.5 49 M6X1.0 6 0-0.018 14.5 - 28 77 12 16 7
Ø10 15 14 4 8 M4X0.7 46 M8X1.0 8 0-0.022 8 5 28 74 12 12.5 9.5
Ø16 15 20 5 8 M5X0.8 47 M10X1.0 10 0-0.022 8 5 28 75 18 12.5 9.5
Ø10, Ø16
Ø6
ACP seriesSmall Pin Cylinder
KCC Co., Ltd.
www.kccpr.com221 -
PNEUMATIC & HYDRAULIC ACP seriesSmall Pin Cylinder
Unit : mm
Bore size A ØCD CX CZ ØD H KK L M PA PB R T TL U WA WB Z
Ø10 15 3.3 3.2 12 4 8 M4XP0.7 46 M8XP1.0 8 18 5 28 87 8 12.5 22.5 82
Ø16 15 5 6.5 18 5 8 M5XP0.8 47 M10XP1.0 8 23 8 28 93 10 12.5 27.5 85
Dimensions-Double Acting/Double Clevis (CB)
Ø10, Ø16
Unit : mm
Bore size A ØD ØFC FT FX FY FZ H KK L M PA PB T TL WA WB
Ø6 15 3 Ø4.5 1.6 24 14 32 8 M3XP0.5 49 M6XP1.0 14.5 - 28 77 16 7
Ø10 15 4 Ø4.5 1.6 24 14 32 8 M4XP0.7 46 M8XP1.0 8 5 28 74 12.5 9.5
Ø16 15 5 Ø4.5 2.3 33 20 42 8 M4XP0.8 47 M10XP1.0 8 5 28 75 12.5 9.5
Dimensions-Double Acting/Rod Side Flange (FA)
Ø6
Ø10, Ø16
KCC Co., Ltd.
www.kccpr.com 231 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Small Pin Cylinder
ACP series
Dimensions-Double Acting/Double Rod (W)
Dimensions-Single Acting Spring Return (S)
Unit : mm
Bore size A ØC ØD H KK L M ØNDh8 PA T TL VA WA
Ø10 15 14 4 8 M4X0.7 49 M8X1.0 8 0-0.022 8 28 105 12 12.5
Ø16 15 20 5 8 M5X0.8 50 M10X1.0 10 0-0.022 8 28 106 18 12.5
Unit : mm
Bore size A ØC ØD H KK M ØNDh8 PA PB T VA WA WBL TL
5~15ST 16~
30ST 31~45ST 46~
60ST 5~15ST 16~
30ST 31~45ST 46~
60ST
Ø6 15 14 3 8 M3XP0.5 M6XP1.0 6 0-0.018 14.5 - 28 8 16 7 39.5 48.5 52.5 66.5 67.5 76.5 80.5 94.5
Ø10 15 14 4 8 M4XP0.7 M8XP1.0 8 0-0.022 8 5 28 12 12.5 9.5 46.5 54 66 78 74.5 82 94 106
Ø16 15 20 5 8 M5XP0.8 M10XP1.0 10 0-0.022 8 5 28 18 12.5 9.5 46 54.5 66.5 78.5 74 82.5 94.5 106.5
KCC Co., Ltd.
www.kccpr.com241 -
PNEUMATIC & HYDRAULIC
Small Pin Cylinder
ACP series
Unit : mm
Bore size A ØC ØD H KK M ØNDh8 PA T VA WA WB
Ø6 15 14 3 8 M3XP0.5 M6XP1.0 6 0-0.018 14.5 28 12 16 3
Ø10 15 14 4 8 M4XP0.7 M8XP1.0 8 0-0.022 8 28 12 12.5 5.5
Ø16 15 20 5 8 M5XP0.8 M10XP1.0 10 0-0.022 8 28 18 12.5 5.5
Bore sizeL TL
5~15ST 16~30ST 31~45ST 46~60ST 5~15ST 16~30ST 31~45ST 46~60ST
Ø6 51.5 60.5 64.5 78.5 79.5 88.5 92.5 106.5
Ø10 48.5 56 68 80 76.5 84 96 108
Ø16 48.5 57 69 81 76.5 85 97 109
Dimensions-Single Acting Spring Extend (T)
Ø6
Ø10, Ø16
KCC Co., Ltd.
www.kccpr.com 251 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Part no. Bore size F KK L ØNDh10 NX R1 V
ACP-B10-I Ø10 8 M4XP0.7 21 3.3 +0.048 0 3.1 8 9
ACP-B16-I Ø16 8 M5XP0.8 25 5 +0.048 0 6.4 12 14
Part no. Bore size ØDd9 Ød L m t Retaining
RingCP-10 Ø10 3.3 +0.030
+0.060 2 15.2 12.2 1 0.5 E2
CP-16 Ø16 5 +0.030+0.060 4 22.7 18.3 1.5 0.7 E4
Part no. Bore size B H M T
RN-06 Ø6 9.2 8 M6XP1.0 4
RN-10 Ø10 12.7 11 M8XP1.0 4
RN-16 Ø16 16.2 14 M10XP1.0 4
Part no. Bore size B H M T
SN-06 Ø6 6.4 5.5 M3XP0.5 2.4
SN-10 Ø10 8.1 7 M4XP0.7 3.2
SN-16 Ø16 9.2 8 M5XP0.8 4
Part no. Bore size ØDd9 Ød L m t Retaining
RingJP-10 Ø10 3.3 +0.030
+0.060 2 15.2 12.2 1 0.5 E2
JP-16 Ø16 5 +0.030+0.060 4 16.2 12.2 1.5 0.7 E4
Dimensions-Accessory
ℓ ℓ
Single Knuckle Joint
Mounting Nut
Clevis Pin Knuckle Pin
Rod End Nut
Material:Stainless steel
Material:Steel
Material:Stainless steel
Material:Brass
Material:Rolled steel
Part no. Bore size F KK L ØNDh10 NX R1 V
ACP-B10-Y Ø10 8 M4XP0.7 21 3.3 +0.048 0 3.2 8 9
ACP-B16-Y Ø16 11 M5XP0.8 25 5 +0.048 0 6.5 12 14
Double Knuckle JointMaterial:Rolled steel
Small Pin Cylinder
ACP series
KCC Co., Ltd.
www.kccpr.com261 -
PNEUMATIC & HYDRAULIC
Direct Mount Type Cylinder
ACD series
ACD series
Mounting styleB Bottom mountingF Front mounting
Bore size20 25 32 40
Ø20 Ø25 Ø32 Ø40
How to Order
SeriesACD Direct mount type cylinder
ACDA Direct mount type cylinder (Air cushion)
Features
Aluminium tube
WIth built-in magnet (Standard)
Square type rod cover enables direct mounting.
Space saving by mounting without bracket.
Front mounting & bottom mounting.
ACD B 32 - S 30
ACD B32-S30
MassUnit : kg
Bore size Ø20 Ø25 Ø32 Ø40
Basic mass
Bottom mounting 0.14 0.23 0.32 0.63
Front mounting 0.14 0.22 0.32 0.62
Additional mass of each 50mm stroke 0.04 0.07 0.09 0.14
Calculation:
EX.) ACD-B32-S100 Basic mass: 0.32(Ø32) / Additional mass: 0.09/50 Cylinder stroke:100mm 0.32 + 0.09/50 X 100 = 0.5kg
Symbol
Double Acting / Single Rod
Rod end attachmentNil Rod end nut(Standard):1pcI Single knuckle jointY Double knuckle joint
Refer page [1]-25 for detail information.
Cylinder strokeBore size Standard stroke Max. stroke
Ø2025, 50, 75, 100, 125, 150, 175, 200, 250,
300, 350, 400, 450, 500650
Ø25Ø32Ø40
Other intermediate strokes available on request. Refer to page [1]-133, for speci cations about custom-made rod
ends.
Number of auto switchesNil 2 pcs1 1 pcN N pcs (N: 3, 4, 5...)
Only for auto switch attached type.
Auto switchReed A/S Model Solid State A/S Model
Nil None Nil NoneC72 D-C72K H7A1 D-H7A1KC73 D-C73K H7A2 D-H7A2KC76 D-C76K H7B D-H7BKC80 D-C80K
Only for auto switch attached type. Refer Auto Switch Catalogue for more information.
Speci cationsAction Double acting single rod
Fluid Air
Proof pressure 15kgf/cm2 (1.5MPa)
Max. operating pressure 9.9kgf/cm2 (0.99MPa)
Min. operating pressure 0.5kgf/cm2 (0.05MPa)Ambient & uid
temperature 5 ~ 60
Operating piston speed 50~750mm/sec
Cushion Rubber bumper(Standard)
Lubrication Not required
Tolerance of thread KS class 2
Tolerance of stroke +1.00
Mounting style Bottom mounting, Front mounting
KCC Co., Ltd.
www.kccpr.com 271 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Direct Mount Type Cylinder
ACD series
Unit : mm
Bore size Effective thread length A B C ØC ØD ØEA KK L N PA PB
Ø20 15.5 18 5.0 22 27 10 20 +00.033 M8X1.25 76 M5X0.8 Depth 9 22 8
Ø25 19.5 22 5.5 26 33 12 26 +00.033 M10X1.25 76 M6X1.0 Depth 11 22 8
Ø32 19.5 22 5.5 30 37.5 12 26 +00.033 M10X1.25 78 M6X1.0 Depth 11 22 8
Ø40 21.0 24 7.0 36 46.5 16 32 +00.039 M14X1.25 104 M8X1.25 Depth 14 27 11
Dimensions-Front Mounting (F)
Bore size LY LZ PA PB Rc(PT) T TL VA WA WB Y Z
Ø20 30.4 33.5 22 8 1/8 27 103 24 29 15 12 39
Ø25 36.4 39 22 8 1/8 31 107 30 29 15 12 43
Ø32 42.4 47 22 8 1/8 31 109 34.5 29 15 12 43
Ø40 52.4 58.5 27 11 1/4 34 138 46.5 37.5 21 15 49
Bore size Rc(PT) T T TL VA WA WB
Ø20 1/8 27 30.4 103 24 29 15
Ø25 1/8 31 36.4 107 30 29 15
Ø32 1/8 31 42.4 109 34.5 29 15
Ø40 1/4 34 52.4 138 46.5 37.5 21
Unit : mm
Bore size Effective thread length A B ØC ØD ØEA KK L ØLC LH LX
Ø20 15.5 18 5.0 27 10 20 +00.033 M8X1.25 76 Ø5.5, Ø9.5 Depth 6.5 15 21
Ø25 19.5 22 5.5 33 12 26 +00.033 M10X1.25 76 Ø6.6, Ø11 Depth 7.5 18 25
Ø32 19.5 22 5.5 37.5 12 26 +00.033 M10X1.25 78 Ø9, Ø14 Depth 10 21 30
Ø40 21.0 24 7.0 46.5 16 32 +00.039 M14X1.25 104 Ø11, Ø17 Depth 12.5 26 38
Dimensions-Bottom Mounting (B)
KCC Co., Ltd.
www.kccpr.com281 -
PNEUMATIC & HYDRAULIC
Small Cylinder (Aluminium Tube)
ACS2 series
ACS2 series
ACS2 - N LB 32 - S 100
SeriesACS2 Double acting single rod small cylinder
ACS2W Double acting double rod small cylinder
Bore size20 25 32 40
Ø20 Ø25 Ø32 Ø40
Number of auto switchesNil 2 pcs1 1 pcN N pcs (N: 3, 4, 5...)
Only for auto switch attached type.
Special orderNil NoneTS Multi-step stroke cylinder(Single rod)TW Multi-step stroke cylinder(Double rod)TD Tandem cylinder
ASJ Stroke adjustable type(in forward direction within 25mm)
BSJ Stroke adjustable type (in forward direction within 50mm)
S Single acting spring returnT Single acting spring extend
SV Heat resistant cylinderSS Stainless steel piston rod
LubricationN Non lubricated (Standard)L Low hydraulic pressure type ( 5kgf/cm2)G Low hydraulic pressure type ( 25kgf/cm2)
Bellows
Material Max. ambient temperature
Nil Without bellowsJ Nylon Tarpaulin 60K Neoprene Cloth 110
Rod end attachmentNil Rod end nut (Standard):1pcI Single knuckle jointY Double knuckle joint
Mounting styleB Standard TR Rod side trunnion
LB Foot TH Head side trunnionFA Rod side ange BC Boss-cut FB Head side ange BF Boss-cut ange CA Single clevis BT Boss-cut trunnion CB Double clevis
How to Order
Symbol
Double Acting /Single Rod
Single Acting /Spring Return
Double Acting /Double Rod
Single Acting /Spring Extend
Features
Tube material: Aluminium
With auto switch, rubber bumper (Standard).
With non-lubricated seal.
Improved bush decreases de ection,
improves lateral load resistance.
Easy maintanance with screw fastening
Auto switchReed A/S Model Solid State A/S Model
Nil None Nil NoneC72 D-C72K H7A1 D-H7A1KC73 D-C73K H7A2 D-H7A2KC76 D-C76K H7B D-H7BKC80 D-C80K
Refer to Auto Switch Catalogue for more information.
Cylinder strokeBore size Standard stroke Max. stroke
Ø20 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 75, 100,
125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 550, 600
1000Ø25 1500
Ø32 2000
Ø40
25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450,
500, 600
2000
Other intermediate strokes is available upon request. Refer to page [1]-133, for Specification about custom-made rod
ends.
KCC Co., Ltd.
www.kccpr.com 291 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
TypeNon-lubricated
Low hydraulic pressureDouble acting, Single rod Double acting, Double rod Single acting spring return /
Single acting spring extendFluid Air Turbine Oil VG32
Proof pressure 15kgf/cm2 (1.5MPa)
Max. operating pressure 10kgf/cm2 (1.0MPa) 5kgf/cm2 (0.5MPa)
Min. operating pressure 0.5kgf/cm2 (0.05MPa) 0.8kgf/cm2 (0.08MPa) Forward: 1.8kgf/cm2 (0.18MPa)Reverse: 2.3kgf/cm2 (0.23MPa) 1.8kgf/cm2 (0.18MPa)
Ambient & uid temperature 5 ~ 60
Operating piston speed 50 ~ 750mm/s, 15 ~ 300mm/s
Cushion Rubber bumper
Tolerance of thread KS class 2
Tolerance of stroke ~250ST: +1.0 0 251~500ST: +1.0
0
Speci cations
Mounting style Standard Axial foot Rod side ange
Head side ange
Integrated clevis
Single clevis
2)Double clevis
Rod side trunnion
Head side trunnion Boss cut Boss cut
angeBoss cuttrunnion
Standard
Mounting screw (1pc) (2pcs) (1pc) (1pc) - - - 1) (1pc) 1) (1pc) (1pc) (1pc) (1pc)
Rod end nut
Clevis pin - - - - - - 3) - - - - -
Option
Single knuckle joint
2)Double knuckle joint
Bellows
1)Trunnion nut is included in the rod side trunnion and head side trunnion. 2)Pin and snap ring are included in double clevis and double knuckle joint. 3)Snap ring is included in clevis pin. Double rod type cylinder includes 2pcs rod end nuts.
Accessory
Small Cylinder (Aluminium Tube)
ACS2 series
Mounting style Minimum Order Quantity
Bore size(mm)Remarks
Ø20 Ø25 Ø32 Ø40
Axial foot 1set (2pcs) LB 20 LB 25/32 LB 40(Round type) Foot 2pcs, Nut 1pc
Flange 1pc FA/FB 20 FA/FB 25/32 FA/FB 40(Round type) Flange 1pc, Nut 1pc
Single clevis 1pc CA 20 CA 25/32 CA 40(Round type) Single clevis 1pc
Double clevis 1pc CB 20 CB 25/32 CB 40(Round type)
Double clevis 1pc,Clevis pin 1pc, Snap ring 2pcs
Trunnion 1pc TC 20 TC 25/32 TC 40 (Round type) Trunnion 1pc, Trunnion nut 1pc
Bore size(mm)Accessory Ø20 Ø25, Ø32 Ø40
Single knuckle joint I20 I25/32 I40
Double knuckle joint Y20 Y25/32 Y40
Rod end attachment of ACS2 40 and that of ACM 40 are the same.
Mounting Style
Rod End Attachment
KCC Co., Ltd.
www.kccpr.com301 -
PNEUMATIC & HYDRAULIC
Small Cylinder (Aluminium Tube)
ACS2 series
Mass
1. Double acting single rod Ex) ACS2-N-LB32-S100
Basis mass: 0.366(FootØ32) / Additional mass: 0.084/50 / Stroke: 100mm 0.366 + 0.084/50 X 100 = 0.534kg
2. Double acting double rod Ex) ACS2W-N-LB32-S100
Basis mass: 0.407(FootØ32) / Additional mass: 0.137/50 / Stroke: 100mm 0.407 + 0.137/50 X 100 = 0.681kg
Unit: kg
Bore size (mm)Double acting, Single rod Double acting, Double rod
Ø20 Ø25 Ø32 Ø40 Ø20 Ø25 Ø32 Ø40
Basis mass
Standard 0.154 0.238 0.288 0.626 0.176 0.283 0.329 0.727
Foot 0.228 0.316 0.366 0.778 0.250 0.361 0.407 0.879
Flange 0.198 0.290 0.340 0.734 0.220 0.335 0.381 0.835
Integrated clevis 0.134 0.208 0.248 0.566 - - - -
Single clevis 0.204 0.290 0.340 0.754 - - - -
Double clevis (With pin) 0.214 0.298 0.348 0.788 - - - -
Trunnion 0.194 0.308 0.348 0.726 0.216 0.353 0.389 0.827
Boss cut 0.144 0.218 0.268 0.596 - - - -
Boss cut ange 0.184 0.268 0.318 0.706 - - - -
Boss cut trunnion 0.184 0.288 0.328 0.696 - - - -Additional mass per each
50mm of stroke 0.064 0.080 0.084 0.140 0.096 0.120 0.137 0.205
Accessory
Single knuckle joint 0.056 0.056 0.056 0.166 - - - -
Double knuckle joint (With pin) 0.074 0.072 0.072 0.220 - - - -
Rod nut 0.002 0.008 0.008 0.016 - - - -
Calculation:
KCC Co., Ltd.
www.kccpr.com 311 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Structure
Standard (Non lubricated type) ACS2-N B
Low hydraulic pressure type ACS2-L
No. Parts Material Remark
1 Rod Carbon Steel Hard Chromium Plating
2 Rod Cover Aluminium Alloy White Anodizing
3 Head Cover Aluminium Alloy White Anodizing
4 Head Cover Aluminium Alloy Boss Cut
5 Piston Aluminium Alloy -
6 Cylinder Tube Aluminium Alloy -
7 Wearing Resin -
8 Magnet NBR -
9 Damper Urethane -
10 Bush SPCC -
No. Parts MaterialBore size
Ø20 Ø25 Ø32 Ø40
Non-lubricated
type
11 Rod Packing NBR DRP10 DRP12 DRP12 DRP16
12 Rod O-Ring NBR S6 S8 S8 S10
13Non-
Lubricated Packing
NBR OPA20 OPA25 OPA32 OPA40
Lowhydraulic pressure
type14
Low Hydraulic
Pressure type Packing
NBR OPA20 OPA25 OPA32 OPA40
Small Cylinder (Aluminium Tube)
ACS2 series
Boss cut typeACS2-N BC
KCC Co., Ltd.
www.kccpr.com321 -
PNEUMATIC & HYDRAULIC
Small Cylinder (Aluminium Tube)
ACS2 series
Unit : mm
Bore size Effective thread length A B ØD ØE H KK L M PA Rc(PT) T TL
Ø20 15.5 18 5.0 10 28 13 M8X1.25 62 M20X1.5 8 1/8 41 116
Ø25 19.5 22 5.5 12 34 13 M10X1.25 62 M26X1.5 8 1/8 45 120
Ø32 19.5 22 5.5 12 38 13 M10X1.25 64 M26X1.5 8 1/8 45 122
Ø40 21.0 24 7.5 16 50 16 M14X1.50 88 M32X2.0 11 1/4 50 154
Unit : mm
Bore size Effective thread length A B ØD H KK L ØLC ØLD LH LS LT LX LZ
Ø20 15.5 18 5.0 10 13 M8X1.25 62 4 6.8 25 102 3 40 55
Ø25 19.5 22 5.5 12 13 M10X1.25 62 4 6.8 28 102 3 40 55
Ø32 19.5 22 5.5 12 13 M10X1.25 64 4 6.8 28 104 3 40 55
Ø40 21.0 24 7.5 16 16 M14X1.50 88 4 7.0 30 134 3 55 75
Bore size M PA Rc(PT) T TL VA VB W X Y
Ø20 M20X1.5 8 1/8 41 118 24 12 15 20 8
Ø25 M26X1.5 8 1/8 45 118 30 12 15 20 8
Ø32 M26X1.5 8 1/8 45 120 32 12 15 20 8
Ø40 M32X2.0 11 1/4 50 158 46 18 21 23 12
Bore size VA VB W
Ø20 24 12 15
Ø25 30 12 15
Ø32 32 12 15
Ø40 46 18 21
Dimensions-Standard (B)
Dimensions-Foot (LB)
Effective thread length
Effective thread length
KCC Co., Ltd.
www.kccpr.com 331 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Small Cylinder (Aluminium Tube)
ACS2 series
Bore size PA Rc(PT) T TL VA VB W Y
Ø20 8 1/8 41 116 24 12 15 40
Ø25 8 1/8 45 120 30 12 15 42
Ø32 8 1/8 45 122 32 12 15 42
Ø40 11 1/4 50 154 46 18 21 52
Bore size PA Rc(PT) T TL VA VB W Y
Ø20 8 1/8 41 116 24 12 15 40
Ø25 8 1/8 45 120 30 12 15 42
Ø32 8 1/8 45 122 32 12 15 42
Ø40 11 1/4 50 154 46 18 21 52
Unit : mm
Bore size Effective thread length A B ØD ØE ØFD FT FX FY FZ H KK L M
Ø20 15.5 18 5.0 10 28 7 3.2 60 - 75 13 M8X1.25 62 M20X1.5
Ø25 19.5 22 5.5 12 34 7 4.5 60 - 75 13 M10X1.25 62 M26X1.5
Ø32 19.5 22 5.5 12 38 7 4.5 60 - 75 13 M10X1.25 64 M26X1.5
Ø40 21.0 24 7.5 16 50 7 4.5 66 36 82 16 M14X1.50 88 M32X2.0
Unit : mm
Bore size Effective thread length A B ØD ØE ØFD FT FX FY FZ H KK L M
Ø20 15.5 18 5.0 10 28 7 3.2 60 - 75 13 M8X1.25 62 M20X1.5
Ø25 19.5 22 5.5 12 34 7 4.5 60 - 75 13 M10X1.25 62 M26X1.5
Ø32 19.5 22 5.5 12 38 7 4.5 60 - 75 13 M10X1.25 64 M26X1.5
Ø40 21.0 24 7.5 16 50 7 4.5 66 36 82 16 M14X1.50 88 M32X2.0
Dimensions-Rod Side Flange (FA)
Dimensions-Head Side Flange (FB)
Effective thread length
Effective thread length
KCC Co., Ltd.
www.kccpr.com341 -
PNEUMATIC & HYDRAULIC
Small Cylinder (Aluminium Tube)
ACS2 series
Bore size R Rc(PT) T TL U VA VB W Z
Ø20 9 1/8 41 142 14 24 12 15 133
Ø25 9 1/8 45 146 14 30 12 15 137
Ø32 9 1/8 45 148 14 32 12 15 139
Ø40 11 1/4 50 188 18 46 18 21 177
Bore size PA R Rc(PT) T TL U VA VB W Z
Ø20 8 9 1/8 41 142 14 24 12 15 133
Ø25 8 9 1/8 45 146 14 30 12 15 137
Ø32 8 9 1/8 45 148 14 32 12 15 139
Ø40 11 11 1/4 50 188 18 46 18 21 177
Dimensions-Single Clevis (CA)
Dimensions-Double Clevis (CB)
Unit : mm
Bore size Effective thread length A B ØCD CR CX ØD ØE H KK L M PA
Ø20 15.5 18 5.0 9 30 10 10 28 13 M8X1.25 62 M20X1.5 8
Ø25 19.5 22 5.5 9 30 10 12 34 13 M10X1.25 62 M26X1.5 8
Ø32 19.5 22 5.5 9 30 10 12 38 13 M10X1.25 64 M26X1.5 8
Ø40 21.0 24 7.5 10 39 15 16 50 16 M14X1.50 88 M32X2.0 11
Unit : mm
Bore size Effective thread length A B ØCD CR CX CZ ØD ØE H KK L M
Ø20 15.5 18 5.0 9 30 10 19 10 28 13 M8X1.25 62 M20X1.5
Ø25 19.5 22 5.5 9 30 10 19 12 34 13 M10X1.25 62 M26X1.5
Ø32 19.5 22 5.5 9 30 10 19 12 38 13 M10X1.25 64 M26X1.5
Ø40 21.0 24 7.5 10 39 15 30 16 50 16 M14X1.50 88 M32X2.0
Effective thread length
Effective thread length
KCC Co., Ltd.
www.kccpr.com 351 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Small Cylinder (Aluminium Tube)
ACS2 series
Bore size TL TT TX ØTY TZ VA VB W Z
Ø20 116 10 32 32 52 24 12 15 36
Ø25 122 10 40 40 60 30 12 15 40
Ø32 124 10 40 40 60 32 12 15 40
Ø40 154 11 53 53 77 46 18 21 44.5
Dimensions-Rod Side Trunnion (TR)
Unit : mm
Bore size Effective thread length A B ØD ØE H KK L M PA Rc(PT) T ØTD
Ø20 15.5 18 5.0 10 28 13 M8X1.25 62 M20X1.5 8 1/8 41 8
Ø25 19.5 22 5.5 12 34 13 M10X1.25 62 M26X1.5 8 1/8 45 9
Ø32 19.5 22 5.5 12 38 13 M10X1.25 64 M26X1.5 8 1/8 45 9
Ø40 21.0 24 7.5 16 50 16 M14X1.50 88 M32X2.0 11 1/4 50 10
Effective thread length
Bore size TL TT TX ØTY TZ VA VB W Z
Ø20 116 10 32 32 52 24 12 15 108
Ø25 122 10 40 40 60 30 12 15 112
Ø32 124 10 40 40 60 32 12 15 114
Ø40 154 11 53 53 77 46 18 21 143.5
Dimensions-Head Side Trunnion (TH)
Unit : mm
Bore size Effective thread length A B ØD ØE H KK L M PA Rc(PT) T ØTD
Ø20 15.5 18 5.0 10 28 13 M8X1.25 62 M20X1.5 8 1/8 41 8
Ø25 19.5 22 5.5 12 34 13 M10X1.25 62 M26X1.5 8 1/8 45 9
Ø32 19.5 22 5.5 12 38 13 M10X1.25 64 M26X1.5 8 1/8 45 9
Ø40 21.0 24 7.5 16 50 16 M14X1.50 88 M32X2.0 11 1/4 50 10
Effective thread length
KCC Co., Ltd.
www.kccpr.com361 -
PNEUMATIC & HYDRAULIC
Small Cylinder (Aluminium Tube)
ACS2 series
Unit : mm
Compact (Boss Cut type)
Bore size TL
Ø20 103
Ø25 107
Ø32 109
Ø40 138
Unit : mm
Dimensions Length Comparison (Comparison with Standard type).
Ø20 Ø25 Ø32 Ø40
-13 -13 -13 -16
The total length of cylinder and space for attachment is reduced by removing the thread portion of head cover.
Dimensions-Boss Cut (BC)
Type of attachment: Standard(BC), Rod side flange type(BF), Rod Side Trunnion (BT) For not shown dimensions, refer to ACS2 Standard type.
KCC Co., Ltd.
www.kccpr.com 371 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
ACS2 seriesSmall Cylinder (Aluminium Tube)
Unit : mmPart No.
Bore size øE F L KK øND NX R V
I20 Ø20 20 16 36 M8X1.25 9 +0.060 9 -0.1
-0.2 10 14
I25/32 Ø25, 32 20 18 38 M10X1.25 9 +0.060 9 -0.1
-0.2 10 14
I40 Ø40 24 22 55 M14X1.50 12 +0.10 16 -0.1
-0.3 15.5 20
Unit : mmPart No.
Bore size øE F L KK øND NX NZ R V
Y20 Ø20 18 16 36 M8X1.25 9 +0.060 9 +0.2
+0.1 18 12 14
Y25/32 Ø25, 32 18 18 38 M10X1.25 9 +0.060 9 +0.2
+0.1 18 10 14
Y40 Ø40 24 30 55 M14X1.50 12 +0.090 16 +0.3
+0.1 38 13 25
Unit : mm
Part No. Bore size C øD H KK T
RN-02 Ø20 15.0 12.5 13 M8X1.25 5
RN-03 Ø25, 32 19.6 16.5 17 M10X1.25 6
RN-04 Ø40 25.4 21.0 22 M14X1.50 8
Unit : mm
Part No. Bore size C øD H KK T
SN-02 Ø20 34.6 29 30 M20X1.5 8
SN-03 Ø25, 32 37 31.5 32 M26X1.5 8
SN-04 Ø40 47.3 40.5 41 M32X2.0 10
Unit : mm
Part No. Bore size øD ød L N m t Remark
CJP-02 Ø20 9 -0.04-0.08 8.6 0
-0.06 19.2 25 1.75 1.15 +0.14 0 -
CJP-03 Ø25, 32 9 -0.04-0.08 8.6 0
-0.06 19.2 25 1.75 1.15 +0.14 0 -
CP-04 Ø40 10 -0.04-0.09 9.6 0
-0.09 30.2 36.2 1.85 1.15 +0.14 0 For clevis
JP-04 Ø40 12 -0.04-0.09 11.5 0
-0.11 38.2 44.2 1.85 1.15 +0.14 0 For knuckle Y
Dimensions-Accessory
Material: Free-cutting steel
Materia: Rolled steel
Materia: Carbon steel
Materia: Rolled steel
Y20, Y25/32Material: Free-cutting steel
Y40 Materia: Cast iron
Single Knuckle Joint
Rod End Nut
Clevis Pin
Nut
Double Knuckle Joint
KCC Co., Ltd.
www.kccpr.com381 -
PNEUMATIC & HYDRAULIC
Small Cylinder (Aluminium Tube)
ACS2 series
Dimensions-Bellows Attached Type (J, K)
Unit : mm
Bore size Effective thread length A B ØD ØE H KK L M PA Rc(PT) T TL
Ø20 15.5 18 5.0 10 28 13 M8X1.25 62 M20X1.5 8 1/8 41 144
Ø25 19.5 22 5.5 12 34 13 M10X1.25 62 M26X1.5 8 1/8 45 152
Ø32 19.5 22 5.5 12 38 13 M10X1.25 64 M26X1.5 8 1/8 45 154
Ø40 21.0 24 7.5 16 50 16 M14X1.50 88 M32X2.0 11 1/4 50 188
Bore size VA VB W
Ø20 24 12 15
Ø25 30 12 15
Ø32 32 12 15
Ø40 46 18 21
Dimensions-Double Rod (W)
Effective thread length
Effective thread length
Unit : mm
Bore size F ØG s t TL
Ø20 16 39 0.3 stroke+3 56 131
Ø25 16 39 0.3 stroke+3 60 135
Ø32 16 39 0.3 stroke+3 60 137
Ø40 18 40 0.25 stroke+3 67 171
Type J K
Material Nylon Tarpaulin Neoprene cloth
Heat Resistant 60 110
For dimensions not shown in these figues, refer to the ACS2 standard type. SUS band is mounted at bellows at delivery.
KCC Co., Ltd.
www.kccpr.com 391 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Small Cylinder (Aluminium Tube)
ACS2 series
Single Rod Multi-Step Stroke Cylinder (TS)
Dimensions-Single Rod Multi-Step Stroke type (TS)
Unit : mm
Bore size TA TB TL
Ø20 48 62 164
Ø25 48 62 168
Ø32 50 64 172
Ø40 67 88 221
For dimensions not shown in these figues, refer to the ACS2 (Standard) type.
Double Rod Multi-Step Stroke Cylinder (TW)
Head side assembly. By integrating two cylinders enable back and forth stroke and three steps control.Ordering notation: A Stroke + B StrokeExample) 150 + 50 (A Side = 150, B Side = 50)
Dimensions-Double Rod Multi-Step Stroke type (TW)
Unit : mm
Bore size TL X
Ø20 232 26
Ø25 240 26
Ø32 244 26
Ø40 310 34
When A and B ports are supplied with air pressure, A and B strokes reverse.
When C and D ports are supplied with air pressure, A and B strokes move forward.
When A and C ports are supplied with air pressure, B stroke move forward.
When B and D ports are supplied with air pressure, A stroke move forward.
By integrating two cylinders in series enable back and forth stroke and two-steps control for a doubled output.Ordering notation: A Stroke + Total StrokeEx) 150 + 200 (A Side = 150, B Side = 50)
When B port is supplied with air pressure, A and B strokes reverse.
When both A and C ports are suppl ied with a ir pressure, forward output is doubled.
When C port is supplied with air pressure, rod and B Stroke move forward.
When A port is supplied with air pressure, rod and A Stroke move forward.
KCC Co., Ltd.
www.kccpr.com401 -
PNEUMATIC & HYDRAULIC
Small Cylinder (Aluminium Tube)
ACS2 series
Tandem Cylinder (TD)
Dimensions-Tandem Cylinder (TD)
ADJUSTMENTADJUSTMENT
ADJUSTMENTADJUSTMENT
ADJUSTMENTADJUSTMENT
Dimensions-Stroke Adjustable (ASJ, BSJ)
To adjust the entire forward stroke from 0mm to 50mm an adjustment mechanism is attached to the head side.
Range of adjustment
Unit : mm
Bore size KK MA MK ØMI MH ML TL
Ø20 M8X1.25 12 8 20 47 20 150
Ø25 M10X1.25 17 10 25 49 22 156
Ø32 M10X1.25 17 10 25 49 22 158
Ø40 M14X1.50 22 12 30 60 26 198
Stroke Adjustable Cylinder (ASJ, BSJ)
ASJ : 25mm adjustmentBSJ : 50mm adjustmentXSJ : Xmm adjustment (X is de ned by user)
Unit : mm
Bore size TA TB TL
Ø20 48 62 164
Ø25 48 62 168
Ø32 50 64 172
Ø40 67 88 221 For dimensions not shown in these figues, refer to the ACS2 standard type.
Two cylinders connected in series for a doubled output.
When A and B ports are supplied with air pressure, reverse operating output is doubled.
When A and C ports are supplied with air pressure, forward operating output is doubled.
KCC Co., Ltd.
www.kccpr.com 411 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Small Cylinder (Aluminium Tube)
ACS2 series
Dimensions-Single Acting Spring Return (S), Spring Extend (T)
Effective thread length
Effective thread length
Unit : mm
Bore size Effective thread length A B ØD E H KK PA Rc(PT) T VA VB W
Ø20 15.5 18 5 10 28 13 M8×1.25 8 1/8 41 24 12 15Ø25 19.5 22 5.5 12 34 13 M10×1.25 8 1/8 45 30 12 15Ø32 19.5 22 5.5 12 38 13 M10×1.25 8 1/8 45 34.5 12 15Ø40 21 24 7 16 50 13 M14×1.5 11 1/4 50 42.5 18 21.5
StrokeBore size
1~50 51~100 101~150 151~200 201~250L TL L TL L TL L TL L TL
Ø20 87 141 112 166 137 191 - - - -Ø25 87 145 112 170 137 195 - - - -Ø32 89 147 114 172 139 197 164 222 - -Ø40 113 179 138 204 163 229 188 254 213 279
Type Lubricated type
Bore size Ø20, Ø25, Ø32, Ø40
Ambient temperature -20~150
Packing Material VITON
Type Lubricated type, Non-lubricated type
Bore size Ø20, Ø25, Ø32, Ø40
Rod Material SUS 303
Heat Resistant Cylinder (SV)Heat resistant cylinder can be used at a high ambient temperature up to150 by equipped with heat-resistant seal.
Stainless steel cylinder rod is selected to prevent the end of rod from corrosion when it is in contact with water during operation.
Speci cations
Stainless Steel Piston Rod (SS)
Speci cations
Single Acting Spring Return
Single Acting Spring Extend
KCC Co., Ltd.
www.kccpr.com 421 -
PNEUMATIC & HYDRAULIC
ACS3 series
Small Cylinder (Stainless Steel Tube)
ACS3 series
ACS3-N B32-S150
Cylinder strokeBore size Standard stroke Max. stroke
Ø2025, 50, 75, 100, 125, 150, 175, 200, 250,
300, 350, 400, 450, 500650
Ø25Ø32Ø40
Other intermediate strokes is available upon request. Refer to page [1]-133, for Specification about custom-made rod
ends.
ACS3 - N B 32 - S 150
SeriesACS3 Double acting single rod small cylinder
ACS3W Double acting double rod small cylinder
Bore size20 25 32 40
Ø20 Ø25 Ø32 Ø40
Number of auto switchesNil 2 pcs1 1 pcN N pcs (N: 3, 4, 5...)
Only for auto switch attached type.
Special orderNil NoneTW Multi-step stroke cylinder (Double rod)
ASJ Stroke adjustable type(in forward direction within 25mm)
BSJ Stroke adjustable type (in forward direction within 50mm)
S Single acting spring returnT Single acting spring extend
SV Heat resistant cylinderSS Stainless steel piston rod
LubricationN Non-lubricated (Standard)L Low hydraulic pressure type ( 5kgf/cm2)
Bellows
Material Max. ambient temperature
Nil Without bellowsJ Nylon Tarpaulin 60K Neoprene Cloth 110
Rod end attachmentNil Rod end nut (Standard):1pcI Single knuckle jointY Double knuckle joint
Mounting styleB Standard CD Integrated Clevis
LB Foot TR Rod Side TrunnionFA Rod Side Flange TH Head Side TrunnionFB Head Side Flange BC Boss-cutCA Single Clevis BF Boss-cut Flange CB Double Clevis BT Boss-cut Trunnion
How to Order
Auto switchReed A/S Model Solid State A/S Model
Nil None Nil NoneC72 D-C72K H7A1 D-H7A1KC73 D-C73K H7A2 D-H7A2KC76 D-C76K H7B D-H7BKC80 D-C80K
Only for auto switch attached type. Refer to Auto Switch Catalogue for more information.
Symbol
Double Acting /Single Rod
Single Acting /Spring Return
Double Acting /Double Rod
Single Acting /Spring Extend
Features
Tube material: Stainless steel
With auto switch, rubber bumper (Standard).
With non-lubricated seal.
Improved bush decreases de ection,
improves lateral load resistance.
Lighter and more compact in size than
that of conventional type.
KCC Co., Ltd.
www.kccpr.com 431 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Small Cylinder (Stainless Steel Tube)
ACS3 series
TypeNon-Lubricated
Low hydraulic pressureDouble acting, Single rod Double acting, Double rod Single acting spring return /
Single acting spring extendFluid Air Turbine Oil VG32
Proof pressure 15kgf/cm2 (1.5MPa)
Max. operating pressure 10kgf/cm2 (1.0MPa) 5kgf/cm2 (0.5MPa)
Min. operating pressure 0.5kgf/cm2 (0.05MPa) 0.8kgf/cm2 (0.08MPa) Forward: 1.8kgf/cm2 (0.18MPa)Reverse: 2.3kgf/cm2 (0.23MPa) 1.8kgf/cm2 (0.18MPa)
Ambient & uid temperature 5 ~ 60
Operating piston speed 50 ~ 750mm/s 15 ~ 300mm/s
Cushion Rubber bumper
Tolerance of thread KS class 2
Tolerance of stroke ~250ST: +1.0 0 251~500ST: +1.0
0
Speci cations
Accessory
Mounting style Minimum order quantity
Bore size(mm)Remarks
Ø20 Ø25 Ø32 Ø40
Axial foot 1set (2pcs) LB 20 LB 25/32 LB 40(Round type) Foot 2pcs, Nut 1pc
Flange 1pc FA/FB 20 FA/FB 25/32 FA/FB 40(Round type) Flange 1pc, Nut 1pc
Single clevis 1pc CA 20 CA 25/32 CA 40(Round type) Single clevis 1pc
Double clevis 1pc CB 20 CB 25/32 CB 40(Round type)
Double clevis 1pc,Clevis pin 1pc, Snap ring 2pcs
Trunnion 1pc TC 20 TC 25/32 TC 40(Round type) Trunnion 1pc, Trunnion nut 1pc
Bore size(mm)Accessory Ø20 Ø25, Ø32 Ø40
Single Knuckle Joint I20 I25/32 I40
Double Knuckle Joint Y20 Y25/32 Y40
Rod end attachment of ACS3 40 and that of ACM 40 are the same. Rod end attachment is the same as ACS2 series. Refer page [1]-37 for more information.
Mounting Style
Rod End Attachment
Mounting style Standard Axial foot
Rod side ange
Head side ange
Integrated clevis
Single clevis
2)Double clevis
Rod side trunnion
Head side trunnion Boss-cut Boss-cut
FlangeBoss-cutTrunnion
Standard
Mounting screw (1pc) (2pcs) (1pc) (1pc) - - - 1) (1pc) 1) (1pc) (1pc) (1pc) (1pc)
Rod end nut
Clevis Pin - - - - - - 3) - - - - -
Option
Single Knuckle Joint
2)Double Knuckle Joint
Bellows
1)Trunnion nut is included in the rod side trunnion and head side trunnion. 2)Pin and snap ring are included in double clevis and double knuckle joint. 3)Snap ring is included in clevis pin. For double rod type cylinder, rod end nuts (2pcs) are included.
KCC Co., Ltd.
www.kccpr.com 441 -
PNEUMATIC & HYDRAULIC
Small Cylinder (Stainless Steel Tube)
ACS3 series
Mass
1. Double acting single rod Ex) ACS3-N-LB32-S100
Basis mass: 0.358(FootØ32) / Additional mass: 0.076/50 / Stroke: 100mm 0.358 + 0.076/50 X 100 = 0.51kg
2. Double acting double rod Ex) ACS3W-N-LB32-S100
Basis mass: 0.398(FootØ32) / Additional mass: 0.124/50 / Stroke: 100mm 0.398 + 0.124/50 X 100 = 0.646kg
Unit: kg
Bore size (mm)Double acting, Single rod Double acting, Double rod
Ø20 Ø25 Ø32 Ø40 Ø20 Ø25 Ø32 Ø40
Basis mass
Standard 0.150 0.228 0.280 0.568 0.171 0.271 0.320 0.659
Foot 0.224 0.306 0.358 0.720 0.245 0.349 0.398 0.811
Flange 0.194 0.280 0.332 0.676 0.215 0.323 0.372 0.767
Integrated clevis 0.130 0.208 0.270 0.528 - - - -
Single clevis 0.200 0.280 0.332 0.696 - - - -
Double clevis (With pin) 0.210 0.288 0.340 0.730 - - - -
Trunnion 0.190 0.298 0.340 0.668 0.211 0.341 0.380 0.759
Boss cut 0.140 0.208 0.260 0.538 - - - -
Boss cut ange 0.180 0.258 0.310 0.648 - - - -
Boss cut trunnion 0.180 0.278 0.320 0.638 - - - -Additional mass per each
50mm of stroke 0.048 0.068 0.076 0.132 0.720 0.102 0.124 0.193
Accessory
Single knuckle joint 0.056 0.056 0.056 0.166 - - - -
Double knuckle joint (With pin) 0.074 0.072 0.072 0.220 - - - -
Rod nut 0.002 0.008 0.008 0.016 - - - -
Calculation:
KCC Co., Ltd.
www.kccpr.com 451 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Small Cylinder (Stainless Steel Tube)
ACS3 series
Part no. Parts Material Remark
1 Rod Carbon Steel Hard Chromium Plating
2 Rod Cover AL Alloy White Anodizing
3 Head Cover AL Alloy White Anodizing
4 Head Cover AL Alloy Boss Cut
5 Piston AL Alloy -
6 Cylinder Tube SUS304 -
7 Wearing Resin -
8 Magnet NBR -
9 Spring Wash Hard Steel Wire -
10 Damper Urethane -
11 Bush Copper -
Part no. Parts MaterialBore size
Ø20 Ø25 Ø32 Ø40
Non lubricated
12 Rod Packing NBR DRP10 DRP12 DRP12 DRP16
13 Rod O-Ring NBR S6 S8 S8 S10
14Non
Lubricated Packing
NBR OPA20 OPA25 OPA32 OPA40
Low hydraulic pressure
15
Low Hydraulic
Pressure type Packing
NBR HSD20 HSD25 HSD32 HSD40
Structure
Standard (Non lubricated) ACS3-N B
Boss cut ACS3-N BC
Low hydraulic pressure type ACS3-L
KCC Co., Ltd.
www.kccpr.com 461 -
PNEUMATIC & HYDRAULIC
Unit : mm
Bore size Effective thread length A B ØC ØD H KK L M PA Rc(PT) T TL
Ø20 15.5 18 5.0 27 10 13 M8X1.25 62 M20X1.5 8 1/8 41 116
Ø25 19.5 22 5.5 33 12 13 M10X1.25 62 M26X1.5 8 1/8 45 120
Ø32 19.5 22 5.5 37.5 12 13 M10X1.25 64 M26X1.5 8 1/8 45 122
Ø40 21.0 24 7.5 46.5 16 16 M14X1.50 88 M32X2.0 11 1/4 50 154
Bore size VA W
Ø20 24 15
Ø25 30 15
Ø32 34.5 15
Ø40 42.5 21
Dimensions-Standard (B)
Effective thread length
Small Cylinder (Stainless Steel Tube)
ACS3 series
Bore size LZ M PA Rc(PT) T TL W X Y
Ø20 55 M20X1.5 8 1/8 41 131 15 20 8
Ø25 55 M26X1.5 8 1/8 45 135 15 20 8
Ø32 55 M26X1.5 8 1/8 45 137 15 20 8
Ø40 75 M32X2.0 11 1/4 50 173 21 23 12
Dimensions-Foot (LB)
Unit : mm
Bore size Effective thread length A B ØD H KK L ØLC ØLD LH LS LT LX
Ø20 15.5 18 5.0 10 13 M8X1.25 62 4 6.8 25 102 3.2 40
Ø25 19.5 22 5.5 12 13 M10X1.25 62 4 6.8 28 102 3.2 40
Ø32 19.5 22 5.5 12 13 M10X1.25 64 4 6.8 28 104 3.2 40
Ø40 21.0 24 7.5 16 16 M14X1.50 88 4 7.0 30 134 3.2 55
Effective thread length
KCC Co., Ltd.
www.kccpr.com 471 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Small Cylinder (Stainless Steel Tube)
ACS3 series
Bore size PA Rc(PT) T TL W Y
Ø20 8 1/8 41 116 15 40
Ø25 8 1/8 45 120 15 42
Ø32 8 1/8 45 122 15 42
Ø40 11 1/4 50 154 21 52
Dimensions-Head Side Flange (FB)
Unit : mm
Bore size Effective thread length A B ØD ØFD FT FX FY FZ H KK L M
Ø20 15.5 18 5.0 10 7 3.2 60 - 75 13 M8X1.25 62 M20X1.5
Ø25 19.5 22 5.5 12 7 4.5 60 - 75 13 M10X1.25 62 M26X1.5
Ø32 19.5 22 5.5 12 7 4.5 60 - 75 13 M10X1.25 64 M26X1.5
Ø40 21.0 24 7.5 16 7 4.5 66 36 82 16 M14X1.50 88 M32X2.0
Effective thread length
Bore size PA Rc(PT) T TL W Y
Ø20 8 1/8 41 116 15 40
Ø25 8 1/8 45 120 15 42
Ø32 8 1/8 45 122 15 42
Ø40 11 1/4 50 154 21 52
Dimensions-Rod Side Flange (FA)
Unit : mm
Bore size Effective thread length A B ØD ØFD FT FX FY FZ H KK L M
Ø20 15.5 18 5.0 10 7 3.2 60 - 75 13 M8X1.25 62 M20X1.5
Ø25 19.5 22 5.5 12 7 4.5 60 - 75 13 M10X1.25 62 M26X1.5
Ø32 19.5 22 5.5 12 7 4.5 60 - 75 13 M10X1.25 64 M26X1.5
Ø40 21.0 24 7.5 16 7 4.5 66 36 82 16 M14X1.50 88 M32X2.0
Effective thread length
KCC Co., Ltd.
www.kccpr.com 481 -
PNEUMATIC & HYDRAULIC
Bore size R Rc(PT) T TL U VA W Z
Ø20 9 1/8 41 142 14 24 15 133
Ø25 9 1/8 45 146 14 30 15 137
Ø32 9 1/8 45 148 14 34.5 15 139
Ø40 11 1/4 50 188 18 42.5 21 177
Dimensions-Single Clevis (CA)
Unit : mm
Bore size Effective thread length A B ØC ØCD CR CX ØD H KK L M PA
Ø20 15.5 18 5.0 27 9 30 10 10 13 M8X1.25 62 M20X1.5 8
Ø25 19.5 22 5.5 33 9 30 10 12 13 M10X1.25 62 M26X1.5 8
Ø32 19.5 22 5.5 37.5 9 30 10 12 13 M10X1.25 64 M26X1.5 8
Ø40 21.0 24 7.5 46.5 10 39 15 16 16 M14X1.50 88 M32X2.0 11
Effective thread length
Small Cylinder (Stainless Steel Tube)
ACS3 series
Bore size PA R Rc(PT) T TL U VA W Z
Ø20 8 9 1/8 41 142 14 24 15 133
Ø25 8 9 1/8 45 146 14 30 15 137
Ø32 8 9 1/8 45 148 14 34.5 15 139
Ø40 11 11 1/4 50 188 18 42.5 21 177
Dimensions-Double Clevis (CB)
Unit : mm
Bore size Effective thread length A B ØC ØCD CR CX CZ ØD H KK L M
Ø20 15.5 18 5.0 27 9 30 10 19 10 13 M8X1.25 62 M20X1.5
Ø25 19.5 22 5.5 33 9 30 10 19 12 13 M10X1.25 62 M26X1.5
Ø32 19.5 22 5.5 37.5 9 30 10 19 12 13 M10X1.25 64 M26X1.5
Ø40 21.0 24 7.5 46.5 10 39 15 30 16 16 M14X1.50 88 M32X2.0
Effective thread length
KCC Co., Ltd.
www.kccpr.com 491 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Small Cylinder (Stainless Steel Tube)
ACS3 series
Unit : mm
Bore size Effective thread length A B ØD H KK L M PA Rc(PT) T ØTD TL
Ø20 15.5 18 5.0 10 13 M8X1.25 62 M20X1.5 8 1/8 41 8 116
Ø25 19.5 22 5.5 12 13 M10X1.25 62 M26X1.5 8 1/8 45 9 120
Ø32 19.5 22 5.5 12 13 M10X1.25 64 M26X1.5 8 1/8 45 9 122
Ø40 21.0 24 7.5 16 16 M14X1.50 88 M32X2.0 11 1/4 50 10 154
Bore size TT TX ØTY TZ W Z
Ø20 10 32 32 52 15 36
Ø25 10 40 40 60 15 40
Ø32 10 40 40 60 15 40
Ø40 11 53 53 77 21 44.5
Dimensions-Rod Side Trunnion (TR)
Effective thread length
Bore size Rc(PT) T TL U VA W Z
Ø20 1/8 41 124 12 24 15 115
Ø25 1/8 45 128 12 30 15 119
Ø32 1/8 45 136 15 34.5 15 124
Ø40 1/4 50 165 15 42.5 21 153
Dimensions-Integrated Clevis (CD)
Unit : mm
Bore size Effective thread length A B ØC ØCD CX ØD H KK L M PA R
Ø20 15.5 18 5.0 27 8 12 10 13 M8X1.25 62 M20X1.5 8 9
Ø25 19.5 22 5.5 33 8 12 12 13 M10X1.25 62 M26X1.5 8 9
Ø32 19.5 22 5.5 37.5 10 20 12 13 M10X1.25 64 M26X1.5 8 12
Ø40 21.0 24 7.5 46.5 10 20 16 16 M14X1.50 88 M32X2.0 11 12
Effective thread length
KCC Co., Ltd.
www.kccpr.com 501 -
PNEUMATIC & HYDRAULIC
Small Cylinder (Stainless Steel Tube)
ACS3 series
Compact Boss cut
Bore size (mm) TL
Ø20 103
Ø25 107
Ø32 109
Ø40 138
Dimensions Length Comparison (Comparison with Standard type).
Ø20 Ø25 Ø32 Ø40
-13 -13 -13 -16
The total length of cylinder and space for attachment is reduced by removing the thread portion of head cover.
Dimensions-Boss cut (BC)
Unit : mm
Bore size Effective thread length A B ØD H KK L M PA Rc(PT) T ØTD TL
Ø20 15.5 18 5.0 10 13 M8X1.25 62 M20X1.5 8 1/8 41 8 118
Ø25 19.5 22 5.5 12 13 M10X1.25 62 M26X1.5 8 1/8 45 9 122
Ø32 19.5 22 5.5 12 13 M10X1.25 64 M26X1.5 8 1/8 45 9 124
Ø40 21.0 24 7.5 16 16 M14X1.50 88 M32X2.0 11 1/4 50 10 154
Bore size TT TX ØTY TZ W Z
Ø20 10 32 32 52 15 108
Ø25 10 40 40 60 15 112
Ø32 10 40 40 60 15 114
Ø40 11 53 53 77 21 143.5
Dimensions-Head Side Trunnion (TH)
Effective thread length
Type of attachment: Standard(BC), Rod side flange type(BF), Rod Side Trunnion(BT) For not shown dimensions, refer to ACS3 standard type.
KCC Co., Ltd.
www.kccpr.com 511 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Small Cylinder (Stainless Steel Tube)
ACS3 series
Unit : mm
Bore size Effective thread length A B ØD H KK L M PA Rc(PT) T TL W
Ø20 15.5 18 5.0 10 13 M8X1.25 62 M20X1.5 8 1/8 41 144 15
Ø25 19.5 22 5.5 12 13 M10X1.25 62 M26X1.5 8 1/8 45 152 15
Ø32 19.5 22 5.5 12 13 M10X1.25 64 M26X1.5 8 1/8 45 154 15
Ø40 21.0 24 7.5 16 16 M14X1.50 88 M32X2.0 11 1/4 50 188 21
Dimensions-Double Rod (W)
Effective thread length
Effective thread length
Effective thread length
Unit : mm
Bore size F ØG s t TL
Ø20 16 39 0.3 Stroke + 3 56 131
Ø25 16 39 0.3 Stroke + 3 60 135
Ø32 16 39 0.3 Stroke + 3 60 137
Ø40 18 40 0.25 Stroke + 3 67 171
For dimensions not shown in these figues, refer to the ACS3 standard type. SUS band is mounted at bellows at delivery.
Dimensions-Bellows Attached Type (J, K)
Type J K
Material Nylon Tarpaulin Neoprene Cloth
Temperature 60 110
KCC Co., Ltd.
www.kccpr.com 521 -
PNEUMATIC & HYDRAULIC
Small Cylinder (Stainless Steel Tube)
ACS3 series
Double Rod Multi-Step Stroke Cylinder (TW)
Forward Stroke Adjustable Cylinder (ASJ, BSJ)
Dimensions-Double Rod Multi-Step Stroke Cylinder (TW)
Dimensions-Forward Stroke Adjustable Cylinder (ASJ, BSJ)
Unit : mm
Bore size KK MA MH ØMI MK ML TL
Ø20 M8X1.25 12 47 20 8 20 150
Ø25 M10X1.25 17 49 25 10 22 156
Ø32 M10X1.25 17 49 25 10 22 158
Ø40 M14X1.50 22 60 30 12 26 198
ADJUSTMENTADJUSTMENT
ADJUSTMENTADJUSTMENT
ADJUSTMENTADJUSTMENT
To adjust the entire forward stroke from 0mm to 50mm an adjustment mechanism is attached to the head side.
ASJ : 25mm adjustmentBSJ : 50mm adjustmentXSJ : Xmm adjustment (X: stroke decided by user)
Unit : mm
Bore size TL X
Ø20 232 26
Ø25 240 26
Ø32 244 26
Ø40 310 34
Range of adjustment
Head side assembly. By integrating two cylinders enable back and forth stroke and three steps control.Ordering notation: A Stroke + B StrokeExample) 150 + 50 (A Side = 150, B Side = 50)
When A and B ports are supplied with air pressure, A and B strokes reverse.
When C and D ports are supplied with air pressure, A and B strokes move forward.
When A and C ports are supplied with air pressure, B stroke move forward.
When B and D ports are supplied with air pressure, A stroke move forward.
KCC Co., Ltd.
www.kccpr.com 531 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Effective thread length
Effective thread length
ACS3 seriesSmall Cylinder (Stainless Steel Tube)
Heat Resistant Cylinder (SV)
Heat resistant cylinder can be used at a high ambient temperature up to 150 by equipped with heat-resistant seal.
Stainless steel cylinder rod is selected to prevent the end of rod from corrosion when it is in contact with water during operation.
Stainless Steel Piston Rod (SS)
Dimensions-Single Acting Spring Return (S), Spring Extend (T)
Unit : mm
Bore size Effective thread length A B C ØD H KK PA Rc(PT) T VA VB W
Ø20 15.5 18 5 28 10 13 M8×1.25 8 1/8 41 24 15 15Ø25 19.5 22 5.5 33.5 12 13 M10×1.25 8 1/8 45 30 15 15Ø32 19.5 22 5.5 37.5 12 13 M10×1.25 8 1/8 45 34.5 15 15Ø40 21 24 7 46.5 16 13 M14×1.5 11 1/4 50 42.5 21.5 21.5
Unit : mm
StrokeBore size
1~50 51~100 101~150 151~200 201~250L TL L TL L TL L TL L TL
Ø20 87 141 112 166 137 191 - - - -Ø25 87 145 112 170 137 195 - - - -Ø32 89 147 114 172 139 197 164 222 - -Ø40 113 179 138 204 163 229 188 254 213 279
Single Acting Spring Return
Single Acting Spring Extend
Type Lubricated type
Bore size Ø20, Ø25, Ø32, Ø40
Ambient temperature -20~150
Packing Material VITON
Type Lubricated type, Non-lubricated type
Bore size Ø20, Ø25, Ø32, Ø40
Rod Material SUS 303
Speci cations Speci cations
KCC Co., Ltd.
www.kccpr.com541 -
PNEUMATIC & HYDRAULIC
Small Cylinder (Aluminium Tube/Air Cushion)
ACS4 series
ACS4 series
Symbol
Double Acting / Single Rod
Double Acting / Double Rod
Features
Aluminum tube With built-in magnet (Standard). With non-lubricated seal. Improved bush decreases de ection and
improves lateral load resistance. Easy maintenance with screw fastening. Rod seal is easy to be replaced
ACS4A - N LB 32 - S 100
Series
ACS4A Double acting single rod small cylinder(With air cushion)
ACS4AW Double acting double rod small cylinder(With air cushion)
Bore size20 25 32 40
Ø20 Ø25 Ø32 Ø40
Number of auto switchesNil 2 pcs1 1 pcN N pcs (N: 3, 4, 5...)
Only for auto switch attached type.
Special orderNil NoneTS Multi-step stroke cylinder(Single rod)TW Multi-step stroke cylinder(Double rod)TD Tandem cylinder
ASJ Stroke adjustable type(in forward direction within 25mm)
BSJ Stroke adjustable type (in forward direction within 50mm)
SV Heat resistant cylinderSS Stainless steel piston rod
LubricationN Non lubricated (Standard)
Bellows
Material Max. ambient temperature
Nil Without bellowsJ Nylon Tarpaulin 60K Neoprene cloth 110
Rod end attachmentNil Rod end nut (Standard):1pcI Single knuckle jointY Double knuckle joint
Mounting styleB Standard CD Integrated clevisLB Foot TR Rod side trunnionFA Rod side ange TH Head side trunnionFB Head side ange BC Boss-cutCA Single clevis BF Boss-cut ange CB Double clevis BT Boss-cut trunnion
How to Order
Cylinder strokeBore size Standard stroke Max. stroke
Ø20 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 75, 100,
125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 550, 600
1000Ø25 1500
Ø32 2000
Ø40
25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450,
500, 600
2000
Other intermediate strokes is available upon request. Refer to page [1]-133, for Specification about custom-made rod
ends.
Auto switchReed A/S Model Solid State A/S Model
Nil None Nil NoneC72 D-C72K H7A1 D-H7A1KC73 D-C73K H7A2 D-H7A2KC76 D-C76K H7B D-H7BKC80 D-C80K
Refer to Auto Switch Catalogue for more information.
KCC Co., Ltd.
www.kccpr.com 551 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Small Cylinder (Aluminium Tube/Air Cushion)
ACS4 series
Speci cations
TypeNon-Lubricated
Double acting, Single rod Double acting, Double rod
Fluid Air
Proof pressure 15kgf/cm2 (1.5MPa)
Max. operating pressure 10kgf/cm2 (1.0MPa)
Min. operating pressure 0.5kgf/cm2 (0.05MPa) 0.8kgf/cm2 (0.08MPa)
Ambient & uid temperature 5 ~ 60
Operating piston speed 50 ~ 1000mm/s
Cushion Air cushion
Tolerance of thread KS class 2
Tolerance of stroke ~250ST: +1.0 0
Mounting style Minimum order quantity
Bore size(mm)Remarks
Ø20 Ø25 Ø32 Ø40
Axial foot 1set (2pcs) LB 20 LB 25/32 LB 40(Round type) Foot 2pcs, Nut 1pc
Flange 1pc FA/FB 20 FA/FB 25/32 FA/FB 40(Round type) Flange 1pc, Nut 1pc
Single clevis 1pc CA 20 CA 25/32 CA 40(Round type) Single clevis 1pc
Double clevis 1pc CB 20 CB 25/32 CB 40(Round type)
Double clevis 1pc,Clevis pin 1pc, Snap ring 2pcs
Trunnion 1pc TC 20 TC 25/32 TC 40 (Round type) Trunnion 1pc, Trunnion nut 1pc
Bore size(mm)Accessory Ø20 Ø25, Ø32 Ø40
Single Knuckle Joint I20 I25/32 I40
Double Knuckle Joint Y20 Y25/32 Y40
Rod end attachment of ACS2 40 and that of ACM 40 are the same. Rod end attachment is the same as ACS2 series. Refer page [1]-37 for more information.
Mounting Style
Rod End Attachment
Accessory
Mounting style Standard Axial foot Rod side ange
Head side ange
Integrated clevis
Single clevis
2)Double clevis
Rod side trunnion
Head side trunnion Boss cut Boss cut
angeBoss cuttrunnion
Standard
Mounting screw (1pc) (2pcs) (1pc) (1pc) - - - 1) (1pc) 1) (1pc) (1pc) (1pc) (1pc)
Rod end nut
Clevis pin - - - - - - 3) - - - - -
Option
Single knuckle joint
2)Double knuckle joint
Bellows
1)Trunnion nut is included in the rod side trunnion and head side trunnion. 2)Pin and snap ring are included in double clevis and double knuckle joint. 3)Snap ring is included in clevis pin. Double rod type cylinder includes 2pcs rod end nuts.
KCC Co., Ltd.
www.kccpr.com561 -
PNEUMATIC & HYDRAULIC
Structure
Standard (Non lubricated) ACS4A-N B
Small Cylinder (Aluminium Tube/Air Cushion)
ACS4 series
Boss-cut ACS4A-N BC
Part no. Parts Material Remark
1 Rod Carbon Steel Hard Chromium Plating
2 Rod Cover AL Alloy White Anodizing
3 Head Cover AL Alloy White Anodizing
4 Head Cover AL Alloy Boss Cut Type
5 Cylinder Tube AL Alloy -
6 Piston AL Alloy -
7 Magnet Holder AL Alloy -
8 Cushion Ring AL Alloy -
9 Cushion Ring Nut AL Alloy -
10 Stop Ring Carbon Tool Steel -
11 Packing Wash Rolled Steel -
12 Bush Sintered Metal -
13 Magnet - -
14 Wearing Resin -
Part no. Parts MaterialBore size
Ø20 Ø25 Ø32 Ø4015 Rod Packing NBR DRP8 DRP10 DRP12 DRP14
16 Cushion Packing NBR - - - -
17 Piston Packing NBR OPA20 OPA25 OPA32 OPA40
18 Rod O-Ring NBR S6 S6 S8 S10
KCC Co., Ltd.
www.kccpr.com 571 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Small Cylinder (Aluminium Tube/Air Cushion)
ACS4 series
Unit : mm
Bore size Effective thread length A B ØD ØE H KK L M PA Rc(PT) T TL
Ø20 15.5 18 5.0 8 28 13 M8X1.25 62 M20X1.5 8 1/8 41 116
Ø25 19.5 22 5.5 10 34 13 M10X1.25 62 M26X1.5 8 1/8 45 120
Ø32 19.5 22 5.5 12 38 13 M10X1.25 64 M26X1.5 8 1/8 45 122
Ø40 21.0 24 7.5 14 50 16 M14X1.50 88 M32X2.0 11 1/4 50 154
Bore size VA VB W Y
Ø20 24 12 15 8.5
Ø25 30 12 15 10
Ø32 32 12 15 12
Ø40 46 18 21 15.5
Dimensions-Standard (B)
Effective thread length
Except dimensions ØD and Y, all of the dimensions above are the same as ACS2 series. (Refer to ACS2 series.)
KCC Co., Ltd.
www.kccpr.com 581 -
PNEUMATIC & HYDRAULIC
ACS5 series
Small Cylinder (Stainless Steel Tube/Air Cushion)
ACS5 series
Symbol
Double Acting /Single Rod
Double Acting /Double Rod
Features
Tube material: Stainless steel
With built-in magnet (Standard).
With non-lubricated seal.
Improved bush decreases de ection,
improves lateral load resistance.
ACS5A-N B32-S150
Cylinder strokeBore size Standard stroke Max. stroke
Ø2025, 50, 75, 100, 125, 150, 175, 200, 250,
300, 350, 400, 450, 500650
Ø25Ø32Ø40
Other intermediate strokes is available upon request. Refer to page [1]-133, for Specification about custom-made rod
ends.
ACS5A - N B 32 - S 150
Series
ACS5A Double acting single rod small cylinder (With air cushion)
ACS5AW Double acting double rod small cylinder(With air cushion)
Bore size20 25 32 40
Ø20 Ø25 Ø32 Ø40
Number of auto switchesNil 2 pcs1 1 pcN N pcs (N: 3, 4, 5...)
Only for auto switch attached type.
Special orderNil NoneTW Multi-step stroke cylinder(Double rod)
ASJ Stroke adjustable type(in forward direction within 25mm)
BSJ Stroke adjustable type (in forward direction within 50mm)
SV Heat resistant cylinderSS Stainless steel piston rod
LubricationN Non lubricated (Standard)
Bellows
Material Max. ambient temperature
Nil Without bellowsJ Nylon Tarpaulin 60K Neoprene cloth 110
Rod end attachmentNil Rod end nut (Standard):1pcI Single knuckle jointY Double knuckle joint
Mounting styleB Standard CD Integrated clevisLB Foot TR Rod side trunnionFA Rod side ange TH Head side trunnionFB Head side ange BC Boss-cutCA Single clevis BF Boss-cut ange CB Double clevis BT Boss-cut trunnion
How to Order
Auto switchReed A/S Model Solid State A/S Model
Nil None Nil NoneC72 D-C72K H7A1 D-H7A1KC73 D-C73K H7A2 D-H7A2KC76 D-C76K H7B D-H7BKC80 D-C80K
Only for auto switch attached type. Refer to Auto Switch Catalogue for more information.
KCC Co., Ltd.
www.kccpr.com 591 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Small Cylinder (Stainless Steel Tube/Air Cushion)
ACS5 series
Speci cations
TypeNon-Lubricated
Double acting, Single rod Double acting, Double rodFluid Air
Proof pressure 15kgf/cm2 (1.5MPa)
Max. operating pressure 10kgf/cm2 (1.0MPa)
Min. operating pressure 0.5kgf/cm2 (0.05MPa) 0.8kgf/cm2 (0.08MPa)Ambient & uid
temperature 5 ~ 60
Operating piston speed 50 ~ 1000mm/s
Cushion Air cushion
Tolerance of thread KS class 2
Tolerance of stroke ~250ST: +1.0 0
Mounting style Minimum order quantity
Bore size(mm)Remarks
Ø20 Ø25 Ø32 Ø40
Axial foot 1set (2pcs) LB 20 LB 25/32 LB 40(Round type) Foot 2pcs, Mounting nut 1pc
Flange 1pc FA/FB 20 FA/FB 25/32 FA/FB 40(Round type) Flange 1pc, Mounting nut 1pc
Single clevis 1pc CA 20 CA 25/32 CA 40(Round type) Single clevis 1pc
Double clevis 1pc CB 20 CB 25/32 CB 40(Round type)
Double clevis 1pc,Clevis pin 1pc, Snap ring 2pcs
Trunnion 1pc TC 20 TC 25/32 TC 40 (Round type) Trunnion 1pc, Trunnion nut 1pc
Bore size(mm)Accessory Ø20 Ø25, Ø32 Ø40
Single knuckle joint I20 I25/32 I40
Double knuckle joint Y20 Y25/32 Y40
Rod end attachment of ACS5 40 and that of ACM 40 are the same. Rod end attachment is the same as ACS2 series. Refer page [1]-37 for more information.
Mounting Style
Rod End Attachment
Accessory
Mounting style Standard Axial foot Rod side ange
Head side ange
Integrated clevis
Single clevis
2)Double clevis
Rod side trunnion
Head side trunnion Boss-cut Boss cut
FlangeBoss cutTrunnion
Standard
Mounting screw (1pc) (2pcs) (1pc) (1pc) - - - 1) (1pc) 1) (1pc) (1pc) (1pc) (1pc)
Rod end nut
Clevis pin - - - - - - 3) - - - - -
Option
Single knuckle joint
2)Double knuckle joint
Bellows
1)Trunnion nut is included in the rod side trunnion and head side trunnion. 2)Pin and snap ring are included in double clevis and double knuckle joint. 3)Snap ring is included in clevis pin. Double rod type cylinder includes 2pcs rod end nuts.
KCC Co., Ltd.
www.kccpr.com 601 -
PNEUMATIC & HYDRAULIC
Small Cylinder (Stainless Steel Tube/Air Cushion)
ACS5 series
Structure
Standard (Non lubricated) ACS5-N B
Boss-cut ACS5-N BC
Part no. Parts Material Remark
1 Rod Carbon Steel Hard Chromium Plating
2 Rod Cover AL Alloy White Anodizing
3 Head Cover AL Alloy White Anodizing
4 Head Cover AL Alloy White Anodizing
5 Cylinder Tube Stainless Steel -
6 Piston AL Alloy -
7 Magnet Holder AL Alloy -
8 Cushion Ring AL Alloy -
9 Cushion Ring Nut AL Alloy -
10 Stop Ring Carbon Tool Steel -
11 Packing Wash Rolled Steel -
12 Bush Sintered Metal -
13 Magnet - -
14 Wearing Resin -
Part no. Parts MaterialBore size
Ø20 Ø25 Ø32 Ø4015 Rod Packing NBR DRP8 DRP10 DRP12 DRP14
16 Cushion Packing NBR - - - -
17 Piston packing NBR OPA20 OPA25 OPA32 OPA40
18 Rod O-Ring NBR S6 S6 S8 S10
KCC Co., Ltd.
www.kccpr.com 611 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Unit : mm
Bore size Effective thread length A B ØC ØD H KK L M PA Rc(PT) T TL
Ø20 15.5 18 5.0 27 8 13 M8X1.25 62 M20X1.5 8 1/8 41 116
Ø25 19.5 22 5.5 33 10 13 M10X1.25 62 M26X1.5 8 1/8 45 120
Ø32 19.5 22 5.5 37.5 12 13 M10X1.25 64 M26X1.5 8 1/8 45 122
Ø40 21.0 24 7.5 46.5 14 16 M14X1.50 88 M32X2.0 11 1/4 50 154
Bore size VA W Y
Ø20 24 15 8
Ø25 30 15 10
Ø32 34.5 15 12
Ø40 42.5 21 15.5
Dimensions-Standard (B)
Effective thread length
Small Cylinder (Stainless Steel Tube/Air Cushion)
ACS5 series
Except dimensions ØD and Y, all of the dimensions above are the same as ACS3 series. (Refer to ACS3 series.)
KCC Co., Ltd.
www.kccpr.com 621 -
PNEUMATIC & HYDRAULIC
Round Cylinder
ACR series
ACR series
ACR - N B 63 - S 100
SeriesACR Round cylinder (Aluminium tube)
Bore size50 63 80 100
Ø50 Ø63 Ø80 Ø100
Cylinder stroke25, 50, 75, 100, 125, 150, 200, 250, 300, 400, 500
LubricationN Non-lubricated type (Standard)
Rod end attachmentNil Rod end nut (Standard) : 1pcI Single knuckle jointY Double knuckle joint
Mounting styleB StandardFA Rod side angeFB Head side angeCB Double clevis
How to Order
ACR-N B63-S100
Symbol
Double Acting /Single Rod
Features
Aluminium tube
Shorthened round cylinder
Lighter weight than that of conventional
type
Flange type and double clevis mounting is
available
Refer to page [1]-133, for specifications about custom-made rod ends.
Type Non lubricated
Cylinder Bore size Ø50, Ø63, Ø80, Ø100
Fluid Air
Proof pressure 15kgf/cm2 (1.5MPa)
Max. operating pressure 9.9kgf/cm2 (0.99MPa)
Min. operating pressure 0.5kgf/cm2 (0.05MPa)
Ambient & fluid temperature 5 ~ 60
Operating piston speed 50 ~ 600mm/sec
Cushion Rubber bumper
Tolerance of thread KS class 2
Tolerance of stroke ~ 1000ST: +1.4 0 , 1001 ~ 1500ST: +1.8
0
Speci cations
KCC Co., Ltd.
www.kccpr.com 631 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Round Cylinder
ACR series
Unit : mm
Bore size Standard stroke range
Long stroke range A AL C D E F PA PB T H I J B KA KK
Ø50 ~300 301~1200 35 32 32 20 30 2 14 12 58 11 56 M8XP1.25Depth16 7 18 M18XP1.5
Ø63 ~300 301~1200 35 32 38 20 32 2 14 12 58 11 69 M10XP1.5Depth16 7 18 M18XP1.5
Ø80 ~300 301~1400 40 37 50 25 40 3 20 16 71 13 87 M10XP1.5Depth22 10 22 M22XP1.5
Ø100 ~300 301~1500 40 37 60 30 50 3 20 16 71 16 108 M12XP1.75Depth22 10 26 M26XP1.5
Unit : mm
Bore size Stroke range B E F FX FD FT T
Ø50 ~750 76 30 2 58 9 9 58
Ø63 ~750 92 32 2 70 11 9 58
Ø80 ~750 104 40 3 82 11 11 71
Ø100 ~750 128 50 3 100 14 14 71
Dimensions-Standard (B)
Dimensions-Rod Side Flange (FA)
Bore size NA Rc(PT) L TA TB TL TC TDH9 TE TG
Ø50 55 1/4 102 13 12 162 M12XP1.25 16 +0.080 7.5 10
Ø63 69 1/4 102 13 12 162 M14XP1.5 18 +0.080 11.5 14.5
Ø80 80 3/8 122 - - 196 - - - -
Ø100 100 1/2 122 - - 196 - - - -
For Ø80, Ø100 cylinder bore size, NA(width cross flat) does not have trunnion mounting tap. Contact us for built-in magnet type.
ØE is on flange mounting. For dimensions not shown in these figues, refer to the standard type.
KCC Co., Ltd.
www.kccpr.com 641 -
PNEUMATIC & HYDRAULIC
Round Cylinder
ACR series
Unit : mm
Bore size Stroke range CD CX CZ CL RR V TT TZ TL
Ø50 ~600 16 - 60 25 20 - 6 86 185
Ø63 ~600 18 - 74 30 22 - 8 105.4 190
Ø80 ~750 18 28 56 35 18 26 - 64 228
Ø100 ~750 22 32 64 43 22 32 - 72 236
Dimensions-Double Clevis (CB)
For dimensions not shown in these figues, refer to the standard type.
Unit : mm
Bore size Stroke range B E F FX FD FT T TL
Ø50 ~750 76 30 2 58 9 9 58 162
Ø63 ~750 92 32 2 70 11 9 58 162
Ø80 ~750 104 40 3 82 11 11 71 196
Ø100 ~750 128 50 3 100 14 14 71 196
Dimensions-Head Side Flange (FB)
ØE is on flange mounting. For dimensions not shown in these figues, refer to the
standard type.
Ø50, Ø63
Ø80, Ø100
KCC Co., Ltd.
www.kccpr.com 651 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Pressurized on rod side
Pressurized on head side
Medium Cylinder
ACM series
ACM series
Series
ACM Double acting single rod medium cylinder
ACMW Double acting double rod medium clylinder
Tube size40 50 63 80 100
Ø40 Ø50 Ø63 Ø80 Ø100
Number of auto switchesNil 2 pcs1 1 pcN N pcs (N: 3, 4, 5...)
Only for auto switch attached type.
Special orderNil NoneTS Multi-step stroke cylinder(Single rod)TW Multi-step stroke cylinder (Double rod)TD Tandem cylinder
ASJ Stroke adjustable type (in forward direction within 25mm)
BSJ Stroke adjustable type (in forward direction within 50mm)
S Single acting spring returnT Single acting spring extend
SV Heat resistant cylinderSS Stainless steel piston rod
Low friction direction
R Side at pressure when pressurized on head side
H Side at pressure when pressurized on rod size
Only for low friction type.
LubricationN Not required(Standard)
L Low hydraulic pressure ( 5kgf/cm2)
G Low hydraulic pressure( 25kgf/cm2)
Q Low friction type
Rod end attachmentNil Rod end nut 1pc (Standard)I Single knuckle jointY Double knuckle joint
Mounting bracketNil None
KA2 TrunnionCB2 Clevis
Mounting styleB Standard CB Double clevis
LB Foot TC Center trunnionFA Rod side ange TA Rod side trunnionFB Head side ange TB Head side trunnionCA Single clevis
How to Order
Symbol
Double Acting /Single Rod
Double Acting /Double Rod
Belows
Material Max. Temperature
Nil Without bellowsJ Nylon Tarpaulin 60K Neoprene Cloth 110
Auto switchReed A/S Model Solid
state A/S Model
Nil None Nil NoneA54 D-A54K F59 D-F59KA56 D-A56K F5P D-F5PKA64 D-A64K J59 D-J59K
A90(V) D-A90(V)K J51 D-J51KA93(V) D-A93(V)K F9N D-F9N(V)KA96(V) D-A96(V)K F9P D-F9P(V)K
F9B D-F9B(V)K Only for auto switch attached type. Refer to Auto Switch Catalogue for more
information.
ACM - N B 80 - S 100
Features
With built-in magnet. (Standard) With non-lubricated seal. Improved cushion ring and special seal increase
the absorbable kinetic energy. Cushion needle avoid detachment.
Cylinder strokeBore size Standard stroke Max. stroke
Ø4025, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 550, 600, 650, 700, 750, 800, 850, 900,
950, 1000
2950Ø50Ø63Ø80
Ø100 Other intermediate strokes is available upon request. Refer to page [1]-133, for specifications about custom-made rod ends.
ACM-N B80-S100
KCC Co., Ltd.
www.kccpr.com 661 -
PNEUMATIC & HYDRAULIC
Medium Cylinder
ACM series
TypeNon-lubricated
Low hydraulic pressureSingle rod Double rod
Fluid Air Turbine Oil VG32
Proof pressure 15kgf/cm2 (1.5MPa)
Max. operating pressure 9.9kgf/cm2 (0.99MPa) Low pressure L type: 5kgf/cm2 (0.5MPa)
Min. operating pressure 0.5kgf/cm2 (0.05MPa) 1.0kgf/cm2 (0.1MPa)
Ambient & uid temperature 5 ~ 60
Operating piston speed 50 ~ 1000mm/sec 0.5 ~ 300mm/sec
Cushion Both side air cushion None
Tolerance of thread KS class 2
Tolerance of stroke ~250ST : +1.00 251 ~ 800ST : +1.4
0
Bore sizeMounting Ø40 Ø50 Ø63 Ø80 Ø100
Foot LB40 LB50 LB63 LB80 LB100
Flange FA/FB40 FA/FB50 FA/FB63 FA/FB80 FA/FB100
Single clevis (With pin) CA40 CA50 CA63 CA80 CA100
Double clevis (WIth pin) CB40 CB50 CB63 CB80 CB100
Foot mounting basically 2 pcs/set.
Bore sizeRod end attahment Ø40 Ø50,
Ø63 Ø80 Ø100
Single knuckle joint I40 I50/63 I80 I100
Double knuckle joint Y40 Y50/63 Y80 Y100
Speci cations
Accessory
Mounting Style Rod End Attachment
Mounting style Standard Foot Rod Side Flange Head Side Flange Single clevis Double clevis Trunnion
StandardRod end nut
Clevis pin - - - - - -
OptionSingle knuckle jointDouble knuckle joint
Bellows
For double clevis type & double knuckle joint type, pin and snap ring are included.
MassUnit: kg
Bore size (mm)Double acting single rod Double acting double rod
Ø40 Ø50 Ø63 Ø80 Ø100 Ø40 Ø50 Ø63 Ø80 Ø100
Basis mass
Standard 0.790 1.134 1.408 2.636 3.536 0.904 1.277 1.580 3.003 3.956
Foot 0.962 1.342 1.712 3.328 4.364 1.076 1.485 1.884 3.695 4.784
Flange 0.924 1.302 1.684 3.150 4.218 1.038 1.445 1.856 3.517 4.638
Single clevis 1.048 1.506 2.146 3.910 5.524 - - - - -
Double clevis (with pin) 1.076 1.596 2.102 4.024 5.694 - - - - -
Trunnion 1.150 1.614 2.208 4.186 7.206 1.264 1.757 2.380 4.553 7.626
Additional mass per each 50mm of stroke 0.168 0.212 0.268 0.456 0.604 0.252 0.277 0.347 0.662 0.906
Accessory
Single knuckle joint 0.166 0.226 0.226 0.488 0.676 - - - - -
Double knuckle joint (with pin) 0.220 0.296 0.296 0.638 0.916 - - - - -
Rod nut 0.016 0.032 0.032 0.048 0.116 - - - - -
Ex) ACM-LB40-S100 Basis mass: 0.962(Foot Ø40) / Addtional mass: 0.168/50 / Stroke: 100mm
0.962+0.168/50X100 = 1.298kg
Calculation:
KCC Co., Ltd.
www.kccpr.com 671 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Medium Cylinder
ACM series
No. Parts Material Remark
1 Rod Cover Aluminium Alloy -
2 Head Cover Aluminium Alloy -
3 Cylinder Tube Aluminium Alloy Hard Anodized Alluminium
4 Piston (Rod Side) Aluminium Alloy -
5 Rod Carbon SteelHard
Chromium Plating
6 Bush Copper -
7 Cushon Needle Stainless Steel -
8 Tie Rod Carbon Steel Zinc Plating
9 Spring Washer HSWR -
10 Tie Rod Nut Carbon Steel Zinc Plating
11 Rod End Nut Rolled Steel Zinc Plating
12 Piston(Head Side) Aluminium Alloy -
Type No. Parts MaterialBore size (mm)
40 50 63 80 100
Non-lubricated
13Non-
lubricated packing
NBR
OPA40 OPA50 OPA63 OPA80 OPA100
14 Tube O-ring Ø38X1.5 Ø48X1.5 S60 S77 S97
15 Cushion packing KP20 KP24 KP24 KP30 KP35
16 Rod packing DRP16 DRP20 DRP20 DRP25 DRP30
17 Needle O-ring AN5 AN5 AN5 AN5 AN5
18 Magnet Ø40 Ø50 Ø63 Ø80 Ø100
19 Rod O-ring S10 S14 S14 S16 S20
20 Wearing Resin SWB40 SWB50 SWB63 SWB80 SWB100
Low hyd. pressure 1) 21
Low hyd. pressure packing
NBR HSD40 HSD50 HSD63 HSD80 HSD100
1) All packings are non-lubricated type except no. 21.
Structure
Standard (Non Lubricated type) ACM N-B
Low Hydraulic Pressure type ACM L
* New version cover has a longer cushion length. It is a patented model.
KCC Co., Ltd.
www.kccpr.com 681 -
PNEUMATIC & HYDRAULIC ACM seriesMedium Cylinder
Unit : mm
Bore size Effective thread length A B C CA CB ØD ØEA H KK L N PA
Ø40 27 30 6 44 17.5 8.5 16 32 12 M14XP1.5 84 M8XP1.25 15.4
Ø50 32 35 7 52 19.5 11 20 40 12 M18XP1.5 90 M8XP1.25 14
Ø63 32 35 7 64 23 11 20 40 12 M18XP1.5 98 M8XP1.25 15
Ø80 37 40 11 78 24 14 25 52 17 M22XP1.5 116 M12XP1.75 17.5
Ø100 37 40 11 92 26.5 14.5 30 52 17 M26XP1.5 126 M12XP1.75 20
Unit : mm
Bore size Effective thread length A B C CA CB ØD ØEA H K KK L ØLD LH
Ø40 27 30 6 44 17.5 8.5 16 32 12 60 M14XP1.5 84 9 40
Ø50 32 35 7 52 19.5 11 20 40 12 70 M18XP1.5 90 9 45
Ø63 32 35 7 64 23 11 20 40 12 85 M18XP1.5 98 11.5 50
Ø80 37 40 11 78 24 14 25 52 17 102 M22XP1.5 116 13.5 65
Ø100 37 40 11 92 26.5 14.5 30 52 17 116 M26XP1.5 126 13.5 75
Bore size PB Rc(PT) T T TL V W
Ø40 6.5 1/4 51 60 138 3 26
Ø50 8 3/8 58 70 151 3 27.5
Ø63 8 3/8 58 83 159 3 29.5
Ø80 13 1/2 71 102 194 7 34
Ø100 13 1/2 72 116 205 7 36.5
Bore size LS LT LX LY N PA PB Rc(PT) T T TL W X Y
Ø40 138 3 42 70 M8XP1.25 15.4 6.5 1/4 51 60 175 26 27 (13)
Ø50 144 3 50 80 M8XP1.25 14 8 3/8 58 70 188 27.5 27 (13)
Ø63 166 3 59 93 M8XP1.25 15 8 3/8 58 83 206 29.5 34 (16)
Ø80 204 5 76 116 M12XP1.75 17.5 13 1/2 71 102 247 34 44 (16)
Ø100 212 5 92 133 M12XP1.75 20 13 1/2 72 116 258 36.5 43 (17)
Dimensions-Standard (B)
Dimensions-Foot (LB)
Effective thread length
Effective thread length
KCC Co., Ltd.
www.kccpr.com 691 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
ACM seriesMedium Cylinder
Unit : mm
Bore size Effective thread length A B C CA CB ØD ØEA FD FQ FT FX FY FZ
Ø40 27 30 6 44 17.5 8.5 16 32 9 65 12 80 42 100
Ø50 32 35 7 52 19.5 11 20 40 9 75 12 90 50 110
Ø63 32 35 7 64 23 11 20 40 11.5 90 15 105 59 130
Ø80 37 40 11 78 24 14 25 52 13.5 110 18 130 76 160
Ø100 37 40 11 92 26.5 14.5 30 52 13.5 126 18 150 92 180
Bore size KK L N PA PB Rc(PT) T T TL V W
Ø40 M14XP1.5 84 M8XP1.25 15.4 6.5 1/4 51 60 138 3 26
Ø50 M18XP1.5 90 M8XP1.25 14 8 3/8 58 70 151 3 27.5
Ø63 M18XP1.5 98 M8XP1.25 15 8 3/8 58 83 159 3 29.5
Ø80 M22XP1.5 116 M12XP1.75 17.5 13 1/2 71 102 194 7 34
Ø100 M26XP1.5 126 M12XP1.75 20 13 1/2 72 116 205 7 36.5
Unit : mm
Bore size Effective thread length A B C CA CB ØD ØEA ØFD FQ FT FX FY FZ H
Ø40 27 30 6 44 17.5 8.5 16 32 9 65 12 80 42 100 12
Ø50 32 35 7 52 19.5 11 20 40 9 75 12 90 50 110 12
Ø63 32 35 7 64 23 11 20 40 11.5 90 15 105 59 130 12
Ø80 37 40 11 78 24 14 25 52 13.5 110 18 130 76 160 17
Ø100 37 40 11 92 26.5 14.5 30 52 13.5 126 18 150 92 180 17
Bore size KK L N PA PB Rc(PT) T T TL W
Ø40 M14XP1.5 84 M8XP1.25 15.4 6.5 1/4 51 60 147 26
Ø50 M18XP1.5 90 M8XP1.25 14 8 3/8 58 70 160 27.5
Ø63 M18XP1.5 98 M8XP1.25 15 8 3/8 58 83 171 29.5
Ø80 M22XP1.5 116 M12XP1.75 17.5 13 1/2 71 102 205 34
Ø100 M26XP1.5 126 M12XP1.75 20 13 1/2 72 116 216 36.5
Dimensions-Rod Side Flange (FA)
Dimensions-Head Side Flange (FB)
Effective thread length
Effective thread length
KCC Co., Ltd.
www.kccpr.com 701 -
PNEUMATIC & HYDRAULIC ACM seriesMedium Cylinder
Unit : mm
Bore size Effective thread length A B C CA CB ØCD CL CV CX ØD ØEA H
Ø40 27 30 6 44 17.5 8.5 10 +0.15+0.10 30 18 15.0 -0.1
-0.3 16 32 12
Ø50 32 35 7 52 19.5 11 12 +0.15+0.10 35 23 18.0 -0.1
-0.3 20 40 12
Ø63 32 35 7 64 23 11 16 +0.15+0.10 40 27 25.0 -0.1
-0.3 20 40 12
Ø80 37 40 11 78 24 14 20 +0.15+0.10 48 34 31.5 -0.1
-0.3 25 52 17
Ø100 37 40 11 92 26.5 14.5 25 +0.15+0.10 58 43 35.5 -0.1
-0.3 30 52 17
Unit : mm
Bore size Effective thread length A B C CA CB ØCD CL CV CX CZ ØD ØEA
Ø40 27 30 6 44 17.5 8.5 10 +0.15+0.10 30 18 15.0 +0.1
+0.3 29.5 16 32
Ø50 32 35 7 52 19.5 11 12 +0.15+0.10 35 23 18.0 +0.1
+0.3 38 20 40
Ø63 32 35 7 64 23 11 16 +0.15+0.10 40 27 25.0 +0.1
+0.3 49 20 40
Ø80 37 40 11 78 24 14 20 +0.15+0.10 48 34 31.5 +0.1
+0.3 61 25 52
Ø100 37 40 11 92 26.5 14.5 25 +0.15+0.10 58 43 35.5 +0.1
+0.3 64 30 52
Bore size KK L N PA PB R Rc(PT) T T TZ W
Ø40 M14XP1.5 84 M8XP1.25 15.4 6.5 (10) 1/4 51 60 165 26
Ø50 M18XP1.5 90 M8XP1.25 14 8 (12) 3/8 58 70 183 27.5
Ø63 M18XP1.5 98 M8XP1.25 15 8 (16) 3/8 58 83 196 29.5
Ø80 M22XP1.5 116 M12XP1.75 17.5 13 (20) 1/2 71 102 235 34
Ø100 M26XP1.5 126 M12XP1.75 20 13 (25) 1/2 72 116 256 36.5
Bore size H KK L N PA PB R Rc(PT) T T TZ W
Ø40 12 M14XP1.5 84 M8XP1.25 15.4 6.5 (10) 1/4 51 60 165 26
Ø50 12 M18XP1.5 90 M8XP1.25 14 8 (12) 3/8 58 70 183 27.5
Ø63 12 M18XP1.5 98 M8XP1.25 15 8 (16) 3/8 58 83 196 29.5
Ø80 17 M22XP1.5 116 M12XP1.75 17.5 13 (20) 1/2 71 102 235 34
Ø100 17 M26XP1.5 126 M12XP1.75 20 13 (25) 1/2 72 116 256 36.5
Dimensions-Single Clevis (CA)
Dimensions-Double Clevis (CB)
Effective thread length
Effective thread length
KCC Co., Ltd.
www.kccpr.com 711 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
ACM seriesMedium Cylinder
Unit : mm
Bore size Effective thread length A B C CA CB ØD ØEA H KK L LZ N
Ø40 27 30 6 44 17.5 8.5 16 32 12 M14XP1.5 84 93 M8XP1.25
Ø50 32 35 7 52 19.5 11 20 40 12 M18XP1.5 90 103 M8XP1.25
Ø63 32 35 7 64 23 11 20 40 12 M18XP1.5 98 107 M8XP1.25
Ø80 37 40 11 78 24 14 25 52 17 M22XP1.5 116 129 M12XP1.75
Ø100 37 40 11 92 26.5 14.5 30 52 17 M26XP1.5 126 135 M12XP1.75
Bore size PA PB Rc(PT) T T ØTD TL TT TX TY TZ V W Z ZZ
Ø40 15.4 6.5 1/4 51 60 15 -0.05-0.10 138 22 85 62 117 3 26 88 98
Ø50 14 8 3/8 58 70 15 -0.05-0.10 151 22 95 74 127 3 27.5 96.5 109.5
Ø63 15 8 3/8 58 83 18 -0.05-0.10 158 28 110 90 148 3 29.5 101.5 111.5
Ø80 17.5 13 1/2 71 102 25 -0.05-0.10 194 34 140 110 192 7 34 122 136
Ø100 20 13 1/2 72 116 25 -0.05-0.10 205 40 162 130 214 7 36.5 128.5 141.5
Dimensions-Center Trunnion (TC), Rod Side Trunnion (TA), Head Side Trunnion (TB)
Effective thread length
Rod Side Trunnion (TA)
Center Trunnion (TC)
Head Side Trunnion (TB)
KCC Co., Ltd.
www.kccpr.com 721 -
PNEUMATIC & HYDRAULIC ACM seriesMedium Cylinder
Unit : mm
Part No. Bore size TA TC TDH10 (Hole) TE TF TH TL TO TR TS TT
KA2-40/50Ø40 80 102 15 +0.070
0 119 60 45 60 17 9 12 17
Ø50 80 112 15 +0.0700 129 60 45 60 17 9 12 17
KA2-63 Ø63 100 130 18 +0.0700 150 73 55 70 20 11 14 22
KA2-80/100Ø80 120 166 25 +0.084
0 192 100 75 90 26 13.5 17 24
Ø100 120 188 25 +0.0840 214 100 75 90 26 13.5 17 24
Part No. TU TX TY Z
KA2-40/5010 85 62 93
10 95 74 103
KA2-63 15 110 90 107
KA2-80/10015 140 110 129
15 162 130 135
Unit : mm
Part No. Bore size B DA DC DDH10 (Hole) DE DF DH DL DO DR DS
CB2-40 Ø40 60 57 65 10 +0.0580 85 52 40 35 10 9 8
CB2-50 Ø50 70 57 65 12 +0.0700 85 52 40 35 10 9 8
CB2-63 Ø63 85 67 80 16 +0.0700 105 66 50 40 12.5 11 10
CB2-80 Ø80 102 93 100 20 +0.0840 130 90 65 60 15 13.5 12
CB2-100 Ø100 116 93 100 25 +0.0840 130 90 65 60 15 13.5 12
Part No. DT DU DX Z
CB2-40 17 11 15 165
CB2-50 17 11 18 183
CB2-63 22 13.5 25 196
CB2-80 24 16.5 31.5 235
CB2-100 24 16.5 35.5 256
Bore size (mm) A B A + B + 90
Ø40~Ø100 12 60 162
Dimensions-Trunnion Bracket (KA2)
Dimensions-Double Clevis Bracket (CB2)
Rotating Angle
KCC Co., Ltd.
www.kccpr.com 731 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
ACM seriesMedium Cylinder
Unit : mmPart No.
Bore size ØE F KK L LS ØND NX R V
I40 Ø40 24 22 M14X1.5 55 69 12 +0.070 16 -0.1
-0.3 15.5 20
I50 Ø50, 63 28 27 M18X1.5 60 74 12 +0.070 16 -0.1
-0.3 15.5 20
I80 Ø80 36 37 M22X1.5 71 91 18 +0.070 28 -0.1
-0.3 22.5 26
I100 Ø100 40 37 M26X1.5 83 105 20 +0.080 30 -0.1
-0.3 24.5 28
Unit : mm
Part No. Bore size ØDd9 Ød L m t
JP-04 Ø40, 50, 63 12 -0.05-0.09 Ø11 44.5 38.2 1.85 1.13
JP-08 Ø80 18 -0.05-0.09 Ø16.5 62.5 55.2 2.15 1.35
JP-10 Ø100 20 -0.06-0.12 Ø18.5 68.2 61.2 2.15 1.35
Unit : mm
Part No. Bore size ØDd9 Ød L m t
CP-04 Ø40 10 -0.04-0.09 Ø9 35.8 29.8 1.85 1.15
CP-05 Ø50 12 -0.04-0.09 Ø11 44.5 38.2 1.9 1.15
CP-06 Ø63 16 -0.05-0.09 Ø14.5 55.3 49.2 1.9 1.15
CP-08 Ø80 20 -0.06-0.11 Ø18.5 68.2 61.2 2.15 1.35
CP-10 Ø100 25 -0.06-0.11 Ø23 71.2 64.2 2.15 1.35
Dimensions-Accessory
Single Knuckle Joint
Unit : mm
Part No. Bore size C ØD H KK T
RN-04 Ø40 25.4 21 22 M14X1.5 8
RN-05 Ø50, 63 31.2 26 27 M18X1.5 11
RN-08 Ø80 37.0 31 32 M22X1.5 13
RN-10 Ø100 47.3 39 41 M26X1.5 16
Rod End Nut Clevis Pin
Knuckle Joint Pin
Unit : mmPart No.
Bore size ØE F KK L ØND NX NZ R V
Y40 Ø40 24 22 M14X1.5 55 12 +0.10 16 +0.3
+0.1 38 15.5 30
Y50 Ø50, 63 28 24 M18X1.5 60 12 +0.10 16 +0.3
+0.1 38 15.5 30
Y80 Ø80 36 33 M22X1.5 71 18 +0.10 28 +0.3
+0.1 55 22.5 43
Y100 Ø100 40 34 M26X1.5 83 20 +0.10 30 +0.3
+0.1 61 24.5 45
Double Knuckle Joint
Material: Free-cutting steel
Material: Rolled steel
Material: Carbon steel
Material: Carbon steel
Material: FC 40
KCC Co., Ltd.
www.kccpr.com 741 -
PNEUMATIC & HYDRAULIC
Unit : mm
Bore size C CA CB ØEA ØEB KK L N PA PB Rc(PT) S
Ø40 44 17.5 8.5 32 43 M14XP1.5 84 M8XP1.25 15.4 6.5 1/4 1/4 stroke
Ø50 52 19.5 11 40 52 M18XP1.5 90 M8XP1.25 14 8 3/8 1/4 stroke
Ø63 64 23 11 40 52 M18XP1.5 98 M8XP1.25 15 8 3/8 1/4 stroke
Ø80 78 24 14 52 65 M22XP1.5 116 M12XP1.75 17.5 13 1/2 1/4 stroke
Ø100 92 26.5 14.5 52 65 M26XP1.5 126 M12XP1.75 20 13 1/2 1/4 stroke
Bore size T T TL V W
Ø40 59 60 146 3 26
Ø50 66 70 159 3 27.5
Ø63 66 83 166 3 29.5
Ø80 80 102 203 7 34
Ø100 81 116 214 7 36.5
For dimensions not shown in these figures, refer to the ACM (Standard) type. SUS band is mounted at bellows at delivery.
Dimensions-Bellows Attached Type (J, K)
ACM seriesMedium Cylinder
Unit : mm
Bore size Effective thread length A B CA CB ØD H KK L PA PB Rc(PT)
Ø40 27 30 6 18 8 16 12 M14XP1.5 84 12.5 6.5 1/4
Ø50 32 35 7 19.5 11 20 12 M18XP1.5 90 14 8 3/8
Ø63 32 35 7 23 11 20 12 M18XP1.5 98 15 9 3/8
Ø80 37 40 11 25 12 25 17 M22XP1.5 116 19 12 1/2
Ø100 37 40 11 27.5 12 30 17 M26XP1.5 126 20 12 1/2
Bore size T TL W
Ø40 51 186 26.5
Ø50 58 206 27.5
Ø63 58 214 29.5
Ø80 71 258 34
Ø100 72 270 36.5
For dimensions not shown in these figues, refer to the ACM (Standard) type.
Dimensions-Double Rod (ACMW)
Effective thread length
Type J K
Material Nylon Tarpaulin Neoprene Cloth
Heat resistant 60 110
KCC Co., Ltd.
www.kccpr.com 751 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
ACM seriesMedium Cylinder
Unit : mmBore size L TL
Ø40 168 222
Ø50 180 241
Ø63 196 257
Ø80 232 310
Ø100 252 330
For dimensions not shown in these figues, refer to the ACM (Standard) type.
Single Rod Multi-Step Stroke Cylinder (TS)
Dimensions-Single Rod Multi-Step Stroke Cylinder (TS)
Double Rod Multi-Step Stroke Cylinder (TW)
Head side assembly. By integrating two cylinders enable back and forth stroke and three steps control.Ordering notation: A Stroke + B StrokeExample) 150 + 50 (A Side = 150, B Side = 50)
Dimensions-Double Rod Multi-Step Stroke Cylinder (TW)
Unit : mm
Bore size L TL
Ø40 168 270
Ø50 180 296
Ø63 196 312
Ø80 232 374
Ø100 252 396
When A and B ports are supplied with air pressure, A and B strokes reverse.
When C and D ports are supplied with air pressure, A and B strokes move forward.
When A and C ports are supplied with air pressure, B stroke move forward.
When B and D ports are supplied with air pressure, A stroke move forward.
By integrating two cylinders in series enable back and forth stroke and two-steps control for a doubled output.Ordering notation: A Stroke + Total StrokeEx) 150 + 200 (A Side = 150, B Side = 50)
When B port is supplied with air pressure, A and B strokes reverse.
When both A and C ports are suppl ied with a ir pressure, forward output is doubled.
When C port is supplied with air pressure, rod and B Stroke move forward.
When A port is supplied with air pressure, rod and A Stroke move forward.
KCC Co., Ltd.
www.kccpr.com 761 -
PNEUMATIC & HYDRAULIC
Unit : mmBore size L TL
Ø40 168 222
Ø50 180 241
Ø63 196 257
Ø80 232 310
Ø100 252 330
Fo r d imens ions no t shown in these figues, refer to the ACM (Standard) type.
ACM seriesMedium Cylinder
Unit : mmBore size ØB C D ZZ
Ø40 Ø32 22 46 181
Ø50Ø42
28 58.5 206.5
Ø63 28 54 210
Ø80Ø50
35 70 257
Ø100 35 70 268
For dimensions not shown in these figues, refer to the ACM (Standard) type.
ADJUSTMENTADJUSTMENT
ADJUSTMENTADJUSTMENT
ADJUSTMENTADJUSTMENT
Two cylinders connected in series for a doubled output.
Tandem Cylinder (TD)
Dimensions-Tandem Cylinder (TD)
Dimensions-Stroke Adjustable Type (ASJ, BSJ)
To adjust the entire forward stroke from 0mm to 50mm an adjustment mechanism is attached to the head side.
Stroke Adjustable Cylinder (ASJ, BSJ)
ASJ : 25mm adjustmentBSJ : 50mm adjustmentXSJ : Xmm adjustment (X is de ned by user)
When A and B ports are supplied with air pressure, reverse operating output is doubled.
When A and C ports are supplied with air pressure, forward operating output is doubled.
Range of adjustment
KCC Co., Ltd.
www.kccpr.com 771 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Heat resistant cylinder can be used at a high ambient temperature up to150 by equipped with heat-resistant seal.
Type No lubricated
Bore size Ø40, Ø50, Ø63, Ø80, Ø100
Temperature -20~150
Packing Material VITON
Stainless steel cylinder rod is selected to prevent the end of rod from corrosion when it is in contact with water during operation.
Type Lubricated, No lubricated
Bore size Ø40, Ø50, Ø63, Ø80, Ø100
Rod Material SUS304
Stainless Steel Piston Rod (SS)Head Resistant Cylinder (SV)
Speci cations Speci cations
ACM seriesMedium Cylinder
Working at low pressure even when sliding resistance is low. Smooth operation is available even in low speed.
Lubrication No lubriacatedDirection of low
friction operation Single direction (R-Air supply, H-Air supply)
Proof Pressure 10.5kgf/cm2 (1.05MPa)Max. operating
pressure 9.9kgf/cm2 (0.99MPa)
Min. operating pressure 0.02kgf/cm2 (0.002MPa)
Cushion None
Inner leakage Below 0.5 I/min (ANR)
Ambient temperature -10~60
1. When used as a balancer etc., follow the example of the application mentioned earlier applying pressure at one port while leaving the other port open to atmosphere.With pressure at rod cover port·········· Low friction side B (Example of application )With pressure at head cover port·········· Low friction side F (Example of application )
2. In both cases, as long as the outside pressure moves the piston rod, low friction can result in the direction of extension and retraction.
Low Friction Cylinder (Q)
Speci cations
Sliding Resistance of Low Friction Side
Dimensions-Low Friction Type (ACM Q)
Applications
Unit : mmBore size L T TL
Ø40 94 51 148
Ø50 100 58 161
Ø63 108 58 169
Ø80 126 71 204
Ø100 136 72 215
0.02
0.025
0.01
0 0.01 0.1 0.2 0.3 0.4 0.5 0.6 0.7
Bore Size
(Con
verte
d int
o re
sista
nce
for e
ach
cylin
der)
Slidi
ng re
sista
nce
(MPa
)
Operating pressure (MPa)
Driving rollerWinding roller
Precision regulator
Moving body
Precision regulator
KCC Co., Ltd.
www.kccpr.com 781 -
PNEUMATIC & HYDRAULIC
Large Cylinder
ACL series
ACL series
Series
ACL Double acting single rod large cylinder
ACLW Double acting double rod large cylinder
Cover materialØ125~Ø200 Ø250~Ø300
Nil AL(Standard) Steel(Standard)FC Steel -
Bellows
Material Max. ambient temperature
Nil Without bellowsJ Nylon Tarpaulin 60K Neoprene Cloth 110
Rod end attachmentNil Rod end nut(Standard) : 1pcI Single knuckle jointY Double knuckle joint
Mounting styleB Standard CB Double Clevis
LB Foot TC Center TrunnionFA Rod Side Flange TA Rod Side TrunnionFB Head Side Flange TB Head Side TrunnionCA Single Clevis
LubricationNil LubricatedN Non lubricated (Standard)
L Low hydraulic pressure( 5kgf/cm2)
G Low hydraulic pressure ( 25kgf/cm2)
MagnetNil Without built-in magnetH Built-in magnet
Tube materialNil ALF Steel
Number of auto switchesNil 2 pcs1 1 pcN N pcs (N: 3, 4, 5...)
Only for auto switch attached type.
Special OrderNil None
TS Multi-step stroke cylinder (Single rod)
TW Multi-step stroke cylinder (Double rod)
TD Tandem cylinder
ASJ Stroke adjustable type(in forward direction within 25mm)
BSJ Stroke adjustable type (in forward direction within 50mm)
SV Heat resistant cylinderSS Stainless steel piston rod
How to Order
ACL-B 140-S125
ACL - B 140 - S 125
Symbol
Double Acting /Single Rod
Double Acting /Double Rod
Auto switchReed A/S Model Solid
state A/S Model
A54 D-A54K F59 D-F59KA56 D-A56K F5P D-F5PKA64 D-A64K J59 D-J59K
A90(V) D-A90(V)K J51 D-J51KA93(V) D-A93(V)K F9N D-F9N(V)KA96(V) D-A96(V)K F9P D-F9P(V)K
F9B D-F9B(V)K Only for auto switch attached type. Refer to Auto Switch Catalogue for more information.
Cylinder strokeBore size Standard stroke Max. stroke
Ø125 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500
2950Ø140 25, 50, 75, 100, 125, 150, 175, 200, 250, 300
Ø150 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500
Ø160 25, 50, 75, 100, 125, 150, 175, 200, 250, 300Ø180 25, 50, 75, 100, 125, 150, 175, 200, 250, 300
-Ø250 50, 100, 150, 200, 250, 300Ø300 -
Other intermediate strokes available on request.
Features
Aluminum tube available for Ø125~Ø300. Ligher weight & auto switch type available. Steel tube : Ø250~Ø300 Excellent durability and performance. Various mounting styles.
Refer to page [1]-133, for specifications about custom-made rod ends.
Bore size125 140 150 160
Ø125 Ø140 Ø150 Ø160180 200 250 300
Ø180 Ø200 Ø250 Ø300
KCC Co., Ltd.
www.kccpr.com 791 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Large Cylinder
ACL series
AccessoryType Double acting single rod
Mounting style Standard Foot Rod side ange
Head side ange
Single clevis
Double clevis
Center trunnion
Standard mounting
Rod end nut
Clevis pin - - - - - -
Option
Single knuckle joint
Double knuckle joint
Bellows
For double clevis and double knuckle joint, pin and snap ring are included.
Bore sizeMounting style Ø125 Ø140 Ø150 Ø160 Ø180 Ø200 Ø250 Ø300
Foot LB125 LB140 LB150 LB160 LB180 LB200 LB250 LB300
Flange FA/FB125
FA/FB140
FA/FB150
FA/FB160
FA/FB180
FA/FB200
FA/FB250
FA/FB300
Single clevis (with pin) CA125 CA140 CA150 CA160 CA180 CA200 CA250 CA300
Double clevis (with pin) CB125 CB140 CB150 CB160 CB180 CB200 CB250 CB300
For foot type mounting, 2 pieces in one set.
Mounting Style
Bore sizeRod end attachment Ø125 Ø140 Ø150,
Ø160 Ø180 Ø200 Ø250 Ø300
Single knuckle joint I125 I140 I150/160 I180 I200 I250 I300
Double knuckle joint Y125 Y140 Y150/160 Y180 Y200 Y250 Y300
Rod End Attachment
Speci cationsType Lubricated, Non-lubricated Low hydraulic pressure
Fluid Air Turbine Oil VG32
Proof pressure 16kgf/cm2 (1.6MPa)
Max. operating pressure 9.9kgf/cm2 (0.99MPa) Low pressure L type:5kgf/cm2 (0.5MPa)
Min. operating pressure 0.8kgf/cm2 (0.08MPa) 1kgf/cm2 (0.1MPa)Ambient & uid
temperature 5 ~ 60
Operating piston speed 50 ~ 500mm/sec 0.5 ~ 200mm/sec
Cushion With cushion Without cushion
Tolerance of thread KS class 2
Tolerance of stroke ~250ST: +1.00 251 ~ 1000ST: +1.4
0 1001 ~ 1500ST: +1.80
KCC Co., Ltd.
www.kccpr.com 801 -
PNEUMATIC & HYDRAULIC
Large Cylinder
ACL series
Mass
1. Double acting single rod (Aluminium tube) Ex) ACL-LB160-S500
Basic mass: 14.70(FootØ160) / Additional mass: 2.20/100 / Cylinder stroke: 500mm 14.70 + 2.20/100 X 500 = 25.70kg
2. Double acting double rod (Aluminium tube) Ex) ACLW-LB125-S500
Basic mass: 7.78(FootØ125) / Additional mass: 2.37/100 / Cylinder stroke: 500mm 7.78 + 2.37/100 X 500 = 19.63kg
Calculation:
Unit: kg
Bore size (mm)
Aluminium tube
Double acting single rod Double acting double rod
Ø125 Ø140 Ø150 Ø160 Ø125 Ø140 Ø150 Ø160
Standard 5.38 6.76 8.82 11.78 5.98 7.38 9.49 12.67
Foot 7.18 8.92 11.58 14.70 7.78 9.54 12.25 15.59
Flange 8.32 12.40 14.96 18.80 8.92 13.02 15.63 19.69
Single clevis 8.60 11.42 14.40 17.76 - - - -
Double clevis (with pin) 8.88 11.74 15.10 18.28 - - - -
Trunnion 9.51 12.49 15.77 19.18 10.11 13.11 16.44 20.07
Additional mass for each 100mm stroke 1.68 1.68 2.16 2.20 2.37 2.44 3.05 3.11
Single knuckle joint 1.04 1.26 1.63 1.63 - - - -
Double knuckle joint (with pin) 1.37 1.88 2.43 2.43 - - - -
Rod end nut 0.16 0.16 0.26 0.26 - - - -
Bas
ic m
ass
Acc
esso
ry
Unit: kg
Bore size (mm)
Steel tube
Double acting single rod Double acting double rod
Ø125 Ø140 Ø160 Ø180 Ø200 Ø250 Ø300 Ø125 Ø140 Ø160 Ø180 Ø200 Ø250 Ø300
Standard 15.20 18.38 25.24 34.16 42.66 79.78 115.94 16.85 20.03 27.12 36.90 45.79 85.36 122.39
Foot 16.83 20.90 28.04 38.36 47.54 89.28 133.22 18.48 22.55 29.92 41.10 50.67 94.86 139.67
Rod side ange 17.88 23.38 31.63 43.99 54.57 101.62 146.14 - - - - - - -
Head side ange 17.88 23.38 31.63 43.99 54.57 101.62 146.14 - - - - - - -
Single clevis 18.27 22.67 30.73 42.55 52.56 98.17 149.22 - - - - - - -
Double clevis (with pin) 18.73 23.42 34.58 44.23 54.59 101.36 154.96 - - - - - - -
Trunnion 19.33 24.11 32.64 44.78 56.65 107.62 156.37 20.98 25.76 34.52 47.52 59.78 113.20 162.82
Additional mass for each 100mm stroke 2.66 3.01 3.58 4.95 5.75 9.08 12.15 3.46 3.81 4.57 6.20 7.29 11.30 15.17
Single knuckle joint 0.91 1.16 1.56 3.07 2.90 5.38 10.82 - - - - - - -
Double knuckle joint (with pin) 1.37 1.81 2.48 4.74 4.59 9.22 17.17 - - - - - - -
Rod end nut 0.16 0.16 0.2 0.32 0.85 1.26 1.43 - - - - - - -
Bas
ic m
ass
Acc
esso
ry
KCC Co., Ltd.
www.kccpr.com 811 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Large Cylinder
ACL series
No. Parts Material Remark
1 Rod CoverAL Alloy Ø125~Ø160
Rolled Steel Sheet Ø180~Ø300
2 Head CoverAL Alloy Ø125~Ø160
Rolled Steel Sheet Ø180~Ø300
3Tube
Ø125~Ø160Ø180~Ø300
AL Alloy Hard Anodized Aluminium
Carbon Steel Tube
Hard Chromium Plating
4 PistonAL Alloy Ø125~Ø160
Cast Iron Ø180~Ø300
5 Rod Carbon Steel Hard Chromium Plating
6 Secondary Block (Ø180~Ø300) Cast Iron Black Oxide
Coating
7 Bush DU Bush -
8 Cushion Needle Brass -
9 Tie Rod Carbon Steel Zinc Plating
10 Spring Washer Hard Steel Wire -
11 Tie Rod Nut Carbon Steel Zinc Plating
12 Secondary Block Grey Cast Iron -
13 Spring Bolt of Secondary Block
Chrome-Molybdenum
Steel -
14 Cushion Ring (Rod Side) Carbon Steel -
15 Cushion Ring(Head Side) Carbon Steel -
16 Rod End Nut Rolled Steel -
17 Cushion Needle (Ø180~Ø300) Rolled Steel -
Structure
Non lubricated ACL N
Low hydrualic pressure ACL L
Non lubricated ACL N
Low hydrualic pressure ACL L
Standard (Lubricated type) (Ø125, Ø140, Ø150, Ø160)
Standard (Lubricated type) (Ø180, Ø200, Ø250, Ø300)
Type No. Parts MaterialBore size
125 140 150 160 180 200 250 300
Lubrication
18 Piston Packing
NBR
AP115 AP130 AP140 AP150 AP165 AP185 AP235 AP285
19 Tube O-Ring
Ø125x W2.0
Ø140x W2.0
Ø150x W2.0
Ø160x W2.0
Ø180x W2.0
Ø200x W2.0
Ø250x W2.0
Ø300x W2.0
20 Cushion Packing PCS50 PCS50 PCS55 PCS55 PCS60 PCS60 PCS75 PCS80
21 Rod Packing DRP35 DRP35 DRP40 DRP40 DRP45 DRP50 DRP60 DRP70
22 Bush O-Ring - - - - AP63 AP67 AP80 AP85
23Cushion Needle O-Ring
S10 S10 S10 S10 S10 S10 S10 S10
24 Magnet Ø125 Ø140 Ø150 Ø160 - - - -
25 Rod O-Ring S26 S26 S30 S30 S35 S40 S48 S50
Note1) Non Lubricated
26 Wearing RESIN HWR8 HWR8 HWR8 HWR8 HWR8 HWR8 HWR8 HWR8
27 Piston Packing NBR OPA
125OPA140
OPA150
OPA160
OPA180
OPA200
OPA250
OPA300
Note2) Low Hyd. Pressure 28 Piston
Packing NBR DXP125
DXP140
DXP150
DXP160 - - - -
Note 1) For non lubricated type, wearing 26 and piston packing 27 are applied, while other packing are the same as that of lubricated type.
Note 2) Piston packing for low pressure type cylinder is piston packing 28, while other packing are the same as that of lubricated type.
KCC Co., Ltd.
www.kccpr.com 821 -
PNEUMATIC & HYDRAULIC ACL seriesLarge Cylinder
Unit : mm
Bore size Effective thread length A B C ØD ØEA ØEB H KK L N PG Rc(PT) SW
Ø125 47 50 15 115 35 59 - 42 M30X1.5 98 M14X1.5 16 1/2 -
Ø140 47 50 15 128 35 59 - 42 M30X1.5 98 M14X1.5 16 1/2 -
Ø150 53 56 17 132 40 59 - 43 M36X1.5 106 M16X1.5 17.5 3/4 -
Ø160 53 56 17 144 40 59 - 43 M36X1.5 106 M16X1.5 17 3/4 -
Ø180 60 63 20 162 45 70 115 48 M40X1.5 111 M18X1.5 17 3/4 17
Ø200 60 63 20 182 50 74 115 48 M45X1.5 111 M20X1.5 16.5 3/4 17
Ø250 67 71 25 225 60 96 140 60 M56X2.0 141 M24X1.5 22 1 20
Ø300 76 80 30 270 70 96 140 60 M64X2.0 146 M30X1.5 22 1 20
Bore size T T TL U W
Ø125 145 110 235 (21) 34
Ø140 161 110 235 (21) 34
Ø150 170 120 256.5 (23) 38
Ø160 184 120 256.5 (23) 38
Ø180 204 135 281 (26) 39
Ø200 226 135 281 (30) 39
Ø250 277 160 342.5 (34) 49
Ø300 330 175 372.5 (41.5) 49
Dimensions-Standard (B)
Only for 125 of ACL series
Effective thread length
Effective thread length
Ø125, Ø140, Ø150, Ø160
Ø180, Ø200, Ø250, Ø300
KCC Co., Ltd.
www.kccpr.com 831 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
ACL seriesLarge Cylinder
Unit : mm
Bore size Effective thread length A AA B C ØD ØEA ØEB H KK L ØLD LH LS LT
Ø125 47 50 145 15 115 35 59 - 42 M30X1.5 98 19 85 188 8
Ø140 47 50 161 15 128 35 59 - 42 M30X1.5 98 19 100 188 9
Ø150 53 56 170 17 132 40 59 - 43 M36X1.5 106 19 105 206 9
Ø160 53 56 184 17 144 40 59 - 43 M36X1.5 106 19 106 206 9
Ø180 60 63 204 20 162 45 70 115 48 M40X1.5 111 24 125 231 10
Ø200 60 63 226 20 182 50 74 115 48 M45X1.5 111 24 132 231 10
Ø250 67 71 277 25 225 60 96 140 60 M56X2.0 141 29 160 301 12
Ø300 76 80 330 30 270 70 96 140 60 M64X2.0 146 33 200 326 15
Bore size LX LY N PG Rc(PT) SW T T TL W X Y
Ø125 100 157.5 M14X1.5 16 1/2 - 110 145 273 34 45 (20)
Ø140 112 180.5 M14X1.5 16 1/2 - 110 161 273 34 45 (20)
Ø150 118 190 M16X1.5 17.5 3/4 - 120 170 301 38 50 (25)
Ø160 118 197 M16X1.5 17 3/4 - 120 184 301 38 50 (25)
Ø180 132 227 M18X1.5 17 3/4 17 135 204 336 39 60 (30)
Ø200 150 245 M20X1.5 16.5 3/4 17 135 226 336 39 60 (30)
Ø250 180 298.5 M24X1.5 22 1 20 160 277 421 49 80 (40)
Ø300 212 365 M30X1.5 22 1 20 175 330 451 49 90 (40)
Dimensions-Foot (LB)
Only for 125 of ACL series
Effective thread length
Effective thread length
Ø125, Ø140, Ø150, Ø160
Ø180, Ø200, Ø250, Ø300
KCC Co., Ltd.
www.kccpr.com 841 -
PNEUMATIC & HYDRAULIC ACL seriesLarge Cylinder
Unit : mm
Bore size Effective thread length A B C ØD ØEA ØEB ØFD FT FX FY FZ H KK
Ø125 47 50 15 115 35 59 - 19 14 190 100 230 42 M30X1.5
Ø140 47 50 15 128 35 59 - 19 20 212 112 255 42 M30X1.5
Ø150 53 56 17 132 40 59 - 19 20 228 115 265 43 M36X1.5
Ø160 53 56 17 144 40 59 - 19 20 236 118 275 43 M36X1.5
Ø180 60 63 20 162 45 70 115 24 25 265 132 320 48 M40X1.5
Ø200 60 63 20 182 50 74 115 24 25 280 150 335 48 M45X1.5
Ø250 67 71 25 225 60 96 140 29 30 355 180 420 60 M56X2.0
Ø300 76 80 30 270 70 96 140 33 30 400 212 475 60 M64X2.0
Bore size L N PG Rc(PT) T T TL U W
Ø125 98 M14X1.5 16 1/2 145 110 232 (25) 34
Ø140 98 M14X1.5 16 1/2 161 110 232 (25) 34
Ø150 106 M16X1.5 17.5 3/4 170 120 252 (27) 38
Ø160 106 M16X1.5 17 3/4 184 120 252 (27) 38
Ø180 111 M18X1.5 17 3/4 204 135 277 (30) 39
Ø200 111 M20X1.5 16.5 3/4 226 135 277 (35) 39
Ø250 141 M24X1.5 22 1 277 160 336 (40) 49
Ø300 146 M30X1.5 22 1 330 175 369 (49) 49
Dimensions-Rod Side Flange (FA)
Ø125, Ø140, Ø150, Ø160
Ø180, Ø200, Ø250, Ø300
Only for 125 of ACL series
Effective thread length
Effective thread length
KCC Co., Ltd.
www.kccpr.com 851 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
ACL seriesLarge Cylinder
Unit : mm
Bore size Effective thread length A B C ØD ØEA ØEB ØFD FT FX FY FZ H KK
Ø125 47 50 15 115 35 59 - 19 14 190 100 230 42 M30X1.5
Ø140 47 50 15 128 35 59 - 19 20 212 112 255 42 M30X1.5
Ø150 53 56 17 132 40 59 - 19 20 228 115 265 43 M36X1.5
Ø160 53 56 17 144 40 59 - 19 20 236 118 275 43 M36X1.5
Ø180 60 63 20 162 45 70 115 24 25 265 132 320 48 M40X1.5
Ø200 60 63 20 182 50 74 115 24 25 280 150 335 48 M45X1.5
Ø250 67 71 25 225 60 96 140 29 30 355 180 420 60 M56X2.0
Ø300 76 80 30 270 70 96 140 33 30 400 212 475 60 M64X2.0
Bore size L N PG Rc(PT) SW T T TL W
Ø125 98 M14X1.5 16 1/2 - 145 110 222 34
Ø140 98 M14X1.5 16 1/2 - 161 110 228 34
Ø150 106 M16X1.5 17.5 3/4 - 170 120 246 38
Ø160 106 M16X1.5 17 3/4 - 184 120 246 38
Ø180 111 M18X1.5 17 3/4 17 204 135 271 39
Ø200 111 M20X1.5 16.5 3/4 17 226 135 271 39
Ø250 141 M24X1.5 22 1 20 277 160 331 49
Ø300 146 M30X1.5 22 1 20 330 175 351 49
Dimensions-Head Side Flange (FB)
Only for 125 of ACL series
Effective thread length
Effective thread length
Ø125, Ø140, Ø150, Ø160
Ø180, Ø200, Ø250, Ø300
KCC Co., Ltd.
www.kccpr.com 861 -
PNEUMATIC & HYDRAULIC ACL seriesLarge Cylinder
Unit : mm
Bore size Effective thread length A B C ØCD CL CT CV CX ØD ØEA ØEB H
Ø125 47 50 15 115 25 +0.100 65 17 48 32 -0.1
-0.3 35 59 - 42
Ø140 47 50 15 128 28 +0.100 75 17 58 36 -0.1
-0.3 35 59 - 42
Ø150 53 56 17 132 32 +0.100 80 20 60 40 -0.1
-0.3 40 59 - 43
Ø160 53 56 17 144 32 +0.100 80 20 60 40 -0.1
-0.3 40 59 - 43
Ø180 60 63 20 162 40 +0.100 90 23 67 50 -0.1
-0.3 45 70 115 48
Ø200 60 63 20 182 40 +0.100 90 25 65 50 -0.1
-0.3 50 74 115 48
Ø250 67 71 25 225 50 +0.100 110 30 80 63 -0.1
-0.3 60 96 140 60
Ø300 76 80 30 270 63 +0.120 130 37 93 80 -0.1
-0.3 70 96 140 60
Bore size KK L N PG Rc(PT) R SW T T TL TZ W
Ø125 M30X1.5 98 M14X1.5 16 1/2 29 - 145 110 302 273 34
Ø140 M30X1.5 98 M14X1.5 16 1/2 32 - 161 110 315 283 34
Ø150 M36X1.5 106 M16X1.5 17.5 3/4 36 - 170 120 342 306 38
Ø160 M36X1.5 106 M16X1.5 17 3/4 36 - 184 120 342 306 38
Ø180 M40X1.5 111 M18X1.5 17 3/4 44 17 204 135 380 336 39
Ø200 M45X1.5 111 M20X1.5 16.5 3/4 44 17 226 135 380 336 39
Ø250 M56X2.0 141 M24X1.5 22 1 55 20 277 160 466 411 49
Ø300 M64X2.0 146 M30X1.5 22 1 68 20 330 175 519 451 49
Dimensions-Single Clevis (CA)
Ø125, Ø140, Ø150, Ø160
Ø180, Ø200, Ø250, Ø300
Only for 125 of ACL series
Effective thread length
Effective thread length
KCC Co., Ltd.
www.kccpr.com 871 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
ACL seriesLarge Cylinder
Unit : mm
Bore size Effective thread length A B C ØCD CL CT CV CX CZ ØD ØEA ØEB H
Ø125 47 50 15 115 25 +0.15+0.10 65 17 48 64 32 +0.3
+0.1 35 59 - 42
Ø140 47 50 15 128 28 +0.15+0.10 75 17 58 72 36 +0.3
+0.1 35 59 - 42
Ø150 53 56 17 132 32 +0.15+0.10 80 20 60 80 40 +0.3
+0.1 40 59 - 43
Ø160 53 56 17 144 32 +0.15+0.10 80 20 60 80 40 +0.3
+0.1 40 59 - 43
Ø180 60 63 20 162 40 +0.15+0.10 90 23 67 100 50 +0.3
+0.1 45 70 115 48
Ø200 60 63 20 182 40 +0.15+0.10 90 25 65 100 50 +0.3
+0.1 50 74 115 48
Ø250 67 71 25 225 50 +0.15+0.10 110 30 80 126 63 +0.3
+0.1 60 96 140 60
Ø300 76 80 30 270 63 +0.15+0.10 130 37 93 160 80 +0.3
+0.1 70 96 140 60
Bore size KK L N PG R Rc(PT) SW T T TL TZ W
Ø125 M30X1.5 98 M14X1.5 16 (29) 1/2 - 145 110 302 273 34
Ø140 M30X1.5 98 M14X1.5 16 (32) 1/2 - 161 110 315 283 34
Ø150 M36X1.5 106 M16X1.5 17.5 (36) 3/4 - 170 120 342 306 38
Ø160 M36X1.5 106 M16X1.5 17 (36) 3/4 - 184 120 342 306 38
Ø180 M40X1.5 111 M18X1.5 17 (44) 3/4 17 204 135 380 336 39
Ø200 M45X1.5 111 M20X1.5 16.5 (44) 3/4 17 226 135 380 336 39
Ø250 M56X2.0 141 M24X1.5 22 (55) 1 20 277 160 466 411 49
Ø300 M64X2.0 146 M30X1.5 22 (68) 1 20 330 175 519 451 49
Dimensions-Double Clevis (CB)
Only for 125 of ACL series
Effective thread length
Effective thread length
Ø125, Ø140, Ø150, Ø160
Ø180, Ø200, Ø250, Ø300
KCC Co., Ltd.
www.kccpr.com 881 -
PNEUMATIC & HYDRAULIC ACL seriesLarge Cylinder
Unit : mm
Bore size Effective thread length A B C ØD ØEA ØEB H KK L LZ N PG Rc(PT)
Ø125 47 50 15 115 35 59 - 42 M30X1.5 98 159 M14X1.5 16 1/2
Ø140 47 50 15 128 35 59 - 42 M30X1.5 98 159 M14X1.5 16 1/2
Ø150 53 56 17 132 40 59 - 43 M36X1.5 106 173 M16X1.5 17.5 3/4
Ø160 53 56 17 144 40 59 - 43 M36X1.5 106 173 M16X1.5 17 3/4
Ø180 60 63 20 162 45 70 115 48 M40X1.5 111 190.5 M18X1.5 17 3/4
Ø200 60 63 20 182 50 74 115 48 M45X1.5 111 190.5 M20X1.5 16.5 3/4
Ø250 67 71 25 225 60 96 140 60 M56X2.0 141 230.5 M24X1.5 22 1
Ø300 76 80 30 270 70 96 140 60 M64X2.0 146 248 M30X1.5 22 1
Bore size RR RT SW T T ØTD TL TX ØTY TZ U W Z ZZ
Ø125 1 50 - 145 110 32 -0.05-0.10 227 170 164 234 (19) 34 170 148
Ø140 1.5 55 - 161 110 36 -0.05-0.10 227 190 184 262 (21.5) 34 172.5 145.5
Ø150 1.5 59 - 170 120 40 -0.05-0.10 248 200 192 275 (22.5) 38 188.5 157.5
Ø160 1.5 59 - 184 120 40 -0.05-0.10 248 212 204 292 (22.5) 38 189 157
Ø180 2 60 17 204 135 45 -0.05-0.10 272.5 236 228 326 (24.5) 39 204 177
Ø200 2 60 17 226 135 45 -0.05-0.10 272.5 265 257 355 (25.5) 39 204 177
Ø250 3 69 20 277 160 56 -0.05-0.10 332.1 335 325 447 (30) 49 243.5 217.5
Ø300 4 79 20 330 175 67 -0.05-0.10 357 400 390 534 (36.5) 49 263.5 232.5
Dimensions-Center Trunnion (TC), Rod Side Trunnion (TA), Head Side Trunnion (TB)
Ø180, Ø200, Ø250, Ø300
Only for 125 of ACL series
Effective thread length
Rod Side Trunnion (TA)
Head Side Trunnion (TB)
Ø125, Ø140, Ø150, Ø160
Effective thread length
Rod Side Trunnion (TA)
Head Side Trunnion (TB)
KCC Co., Ltd.
www.kccpr.com 891 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
ACL seriesLarge Cylinder
Unit : mm
Part no. Bore size ØE F1 F2 KK L ØND
I125 125 46 8 54 M30X1.5 100 25 +0.1 0
I140 140 48 8 54 M30X1.5 105 28 +0.1 0
I150 150, 160 55 8 60 M36X1.5 110 32 +0.1 0
I180 180 70 8 67 M40X1.5 125 40 +0.1 0
I200 200 70 8 67 M45X1.5 125 40 +0.1 0
I250 250 85 8 75.5 M56X2.0 160 50 +0.1 0
I300 300 105 8 84.5 M64X2.0 175 63 +0.1 0
Part no. NX RR U
I125 32 -0.1-0.3 27 33
I140 36 -0.1-0.3 30 39
I150 40 -0.1-0.3 34 39
I180 50 -0.1-0.3 42.5 44
I200 50 -0.1-0.3 42.5 44
I250 63 -0.1-0.3 53 66
I300 80 -0.1-0.3 66 71
Unit : mm
Part no. Bore size ØE F1 F2 KK L ØND
Y125 125 46 8 58 M30X1.5 100 25 +0.1 0
Y140 140 48 8 58 M30X1.5 105 28 +0.1 0
Y150 150, 160 55 8 64 M36X1.5 110 32 +0.1 0
Y180 180 70 8 71 M40X1.5 125 40 +0.1 0
Y200 200 70 8 71 M45X1.5 125 40 +0.1 0
Y250 250 86 9 79 M56X2.0 160 50 +0.1 0
Y300 300 105 9 88 M64X2.0 175 63 +0.1 0
Part no. NX NZ RR U
Y125 32 +0.3+0.1 64 -0.1
-0.3 27 42
Y140 36 +0.3+0.1 72 -0.1
-0.3 30 47
Y150 40 +0.3+0.1 80 -0.1
-0.3 34 46
Y180 50 +0.3+0.1 100 -0.1
-0.3 42.5 54
Y200 50 +0.3+0.1 100 -0.1
-0.3 42.5 54
Y250 63 +0.3+0.1 126 -0.1
-0.3 53 81
Y300 80 +0.3+0.1 160 -0.1
-0.3 66 87
Unit : mm
Part no. Bore size ØD Ød L m t
CJP-12 125 25 -0.06-0.11 23.9 0
-0.21 72 64.3 2.5 1.35
CJP-14 140 28 -0.06-0.11 26.6 0
-0.21 80.6 72.3 2.5 1.65
CJP-15 150, 160 32 -0.08-0.14 30.3 0
-0.25 89.6 80.3 3 1.65
CJP-18 180, 200 40 -0.08-0.14 38 0
-0.25 110.1 100.3 3 1.9
CJP-25 250 50 -0.08-0.11 47 0
-0.25 138.9 126.5 4 2.2
CJP-30 300 63 -0.10-0.17 60 0
-0.3 172.9 160.5 4 2.2
Unit : mm
Part no. Bore size C D H KK T
RN-12 125, 140 53.1 44 46 M30X1.5 18
RN-15 150, 160 63.5 53 55 M36X1.5 21
RN-18 180 69.3 57 60 M40X1.5 23
RN-20 200 80.8 67 70 M45X1.5 27
RN-25 250 98.1 82 85 M56X2.0 34
RN-30 300 110 92 95 M64X2.0 38
Dimensions-Accessory
Single Knuckle Joint
Rod End Nut Knuckle Joint Pin/ Clevis Pin
Double Knuckle Joint
Material: Free-cutting steel
Material: Rolled steel Material: Carbon Steel
Material: FC 40
KCC Co., Ltd.
www.kccpr.com 901 -
PNEUMATIC & HYDRAULIC ACL seriesLarge Cylinder
Unit : mm
Bore size C ØEB F KK N L PG Rc(PT) S T T TL U W
Ø125 115 75 40 M30X1.5 M14X1.5 98 16 1/2
0.2 X Stroke
133 145 258 (21) 34
Ø140 128 75 40 M30X1.5 M14X1.5 98 16 1/2 133 161 258 (21) 34
Ø150 132 75 40 M36X1.5 M16X1.5 106 17.5 3/4 141 170 277.5 (23) 38
Ø160 144 75 40 M36X1.5 M16X1.5 106 17 3/4 141 184 277.5 (23) 38
Ø180 162 85 45 M40X1.5 M18X1.5 111 17 3/4 153 204 299 (26) 39
Ø200 182 90 45 M45X1.5 M20X1.5 111 16.5 3/4 153 226 299 (30) 39
Ø250 225 105 55 M56X2.0 M24X1.5 141 22 10.17 X Stroke
176 277 358.5 (34) 49
Ø300 270 115 55 M64X2.0 M30X1.5 146 22 1 190 330 387.5 (36.5) 49
For dimensions not shown in these figues, refer to the ACL (Standard) type. SUS band is mounted at bellows at delivery.
Dimensions-Bellows Attached Type (J, K)
Ø180, Ø200, Ø250, Ø300
Ø125, Ø140, Ø150, Ø160
Type J K
Material Nylon Tarpaulin Neoprene Cloth
Temperature 60 110
KCC Co., Ltd.
www.kccpr.com 911 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
ACL seriesLarge Cylinder
Unit : mm
Bore size Effective thread length A B C ØD ØEA ØEB H KK L N PG Rc(PT) SW
Ø125 47 50 15 115 35 59 - 42 M30X1.5 98 M14X1.5 16 1/2 -
Ø140 47 50 15 128 35 59 - 42 M30X1.5 98 M14X1.5 16 1/2 -
Ø150 53 56 17 132 40 59 - 43 M36X1.5 106 M16X1.5 17.5 3/4 -
Ø160 53 56 17 144 40 59 - 43 M36X1.5 106 M16X1.5 17 3/4 -
Ø180 60 63 20 162 45 70 115 48 M40X1.5 111 M18X1.5 17 3/4 17
Ø200 60 63 20 182 50 74 115 48 M45X1.5 111 M20X1.5 16.5 3/4 17
Ø250 67 71 25 225 60 96 140 60 M56X2.0 141 M24X1.5 22 1 20
Ø300 76 80 30 270 70 96 140 60 M64X2.0 146 M30X1.5 22 1 20
Bore size T T TL W
Ø125 145 110 318 34
Ø140 161 110 318 34
Ø150 170 120 346 38
Ø160 184 120 346 38
Ø180 204 135 381 39
Ø200 226 135 381 39
Ø250 277 160 461 49
Ø300 330 175 496 49
Dimensions-Double Rod (ACLW)
Only for 125 of ACL series
Effective thread length
Effective thread length
Ø180, Ø200, Ø250, Ø300
Ø125, Ø140, Ø150, Ø160
KCC Co., Ltd.
www.kccpr.com 921 -
PNEUMATIC & HYDRAULIC ACL seriesLarge Cylinder
By integrating two cylinders in series enable back and forth stroke and two-steps control for a doubled output.Ordering notation: A Stroke + Total StrokeEx) 150 + 200 (A Side = 150, B Side = 50)
Single Rod Multi-Step Stroke Cylinder (TS)
Ø180, Ø200, Ø250, Ø300
Ø125, Ø140, Ø150, Ø160
Unit : mm
Bore size L TL U
Ø125 197 334 (21)
Ø140 197 334 (21)
Ø150 213 363.5 (23)
Ø160 213 363.5 (23)
Ø180 223 393 (26)
Ø200 223 393 (30)
Ø250 283 484.5 (34)
Ø300 293 519.5 (41.5)
Dimensions-Single Rod Multi-Step Stroke Cylinder (TS)
For dimensions not shown in these figues, refer to the ACL (Standard) type.
When B port is supplied with air pressure, A and B strokes reverse.
When both A and C ports are suppl ied with a ir pressure, forward output is doubled.
When C port is supplied with air pressure, rod and B Stroke move forward.
When A port is supplied with air pressure, rod and A Stroke move forward.
KCC Co., Ltd.
www.kccpr.com 931 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
ACL seriesLarge Cylinder
Head side assembly. By integrating two cylinders enable back and forth stroke and three steps control.Ordering notation: A Stroke + B StrokeExample) 150 + 50 (A Side = 150, B Side = 50)
Double Rod Multi-Step Stroke Cylinder (TW)
Ø180, Ø200, Ø250, Ø300
Ø125, Ø140, Ø150, Ø160
Unit : mm
Bore size L TL
Ø125 196 416
Ø140 196 416
Ø150 212 452
Ø160 212 452
Ø180 222 492
Ø200 222 492
Ø250 282 602
Ø300 292 642
Dimensions-Double Rod Multi-Step Stroke Cylinder (TW)
When A and B ports are supplied with air pressure, A and B strokes reverse.
When C and D ports are supplied with air pressure, A and B strokes move forward.
When A and C ports are supplied with air pressure, B stroke move forward.
When B and D ports are supplied with air pressure, A stroke move forward.
For dimensions not shown in these figues, refer to the ACL (Standard) type.
KCC Co., Ltd.
www.kccpr.com 941 -
PNEUMATIC & HYDRAULIC ACL seriesLarge Cylinder
Two cylinders connected in series for a doubled output.
Unit : mm
Bore size L TL U
Ø125 196 333 (21)
Ø140 196 333 (21)
Ø150 212 362.5 (23)
Ø160 212 362.5 (23)
Ø180 222 392 (26)
Ø200 222 392 (30)
Ø250 282 483.5 (34)
Ø300 292 518.5 (41.5)
Tandem Cylinder (TD)
Ø180, Ø200, Ø250, Ø300
Ø125, Ø140, Ø150, Ø160
Dimensions-Tandem Cylinder (TD)
For dimensions not shown in these figues, refer to the ACL (Standard) type.
When A and B ports are supplied with air pressure, reverse operating output is doubled.
When A and C ports are supplied with air pressure, forward operating output is doubled.
KCC Co., Ltd.
www.kccpr.com 951 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
ACL seriesLarge Cylinder
Unit : mm
Bore size ØB C ØD E ØEB H KK TL
Ø125 60 37 35 39 90 43 M30X1.5 318
Ø140 60 37 35 30 90 43 M30X1.5 318
Ø150 60 46 40 26 90 43 M36X1.5 341
Ø160 60 46 40 26 90 43 M36X1.5 341
Ø180 70 52 45 30 115 48 M40X1.5 376
Ø200 70 52 50 30 115 48 M45X1.5 376
Ø250 86 60 60 35 140 60 M56X2.0 456
Ø300 86 60 70 35 140 60 M64X2.0 496
For dimensions not shown in these figues, refer to the ACL standard type.
Forward Stroke Adjustable Cylinder (ASJ, BSJ)
Dimensions-Forward Stroke Adjustable (ASJ, BSJ)
Ø180, Ø200, Ø250, Ø300
Ø125, Ø140, Ø150, Ø160
ADJUSTMENTADJUSTMENTADJUSTMENTADJUSTMENT
ADJUSTMENTADJUSTMENTADJUSTMENTADJUSTMENT
Range of adjustment
ASJ : 25mm adjustmentBSJ : 50mm adjustmentXSJ : Xmm adjustment (X is de ned by user)
To adjust the entire forward stroke from 0mm to 50mm an adjustment mechanism is attached to the head side.
Heat resistant cylinder can be used at a high ambient temperature up to150 by equipped with heat-resistant seal.
Type Lubricated type
Bore size Ø125, Ø140, Ø150, Ø160, Ø180, Ø200
Ambient temperature -20 ~ 150
Packing material VITON
Stainless steel cylinder rod is selected to prevent the end of rod from corrosion when it is in contact with water during operation.
Type Lubricated type, Non-Lubricated type
Bore size Ø125, Ø140, Ø150, Ø160, Ø180, Ø200, Ø250, Ø300
Rod material SUS304
Heat Resistant Cylinder (SV) Stainless Steel Piston Rod (SS)
Speci cation Speci cation
KCC Co., Ltd.
www.kccpr.com 961 -
PNEUMATIC & HYDRAULIC
Extra-Large Cylinder
ACX series
ACX series
ACX - TC 400 - S 600
SeriesACX Extra-large cylinder
Cylinder stroke ~ 1000mm
Mounting styleLB Foot FA Rod side ange FB Head side angeCA Single clevisTC Center trunnion
CushionNil Both side cushionN Without cushionR Rod side cuhsionH Head side cushion
Bore size350 ø350400 ø400450 ø450
Rod end attachmentNil NoneI Single knuckle jointY Double knuckle joint
Mounting style
Bore size
Basic mass
LB FA FB TC CA
Additional mass for
each 100mm stroke
Ø350 410 410 410 410 410 24
Ø400 540 540 540 540 540 28
Ø450 679 679 679 679 679 34
Action Double acting
Fluid Air
Proof pressure 16kgf/cm2 (1.6MPa)
Max. operating pressure 9.9kgf/cm2 (0.99MPa)
Min. operating pressure 1.0kgf/cm2 (0.1MPa)Ambient & uid
temperature 5 ~ 60
Operating piston speed 50~500mm/sec
Tolerance of thread KS class 2
How to Order
Mass
Speci cationsTolerance of stroke
100mm +0.80 251~630mm +1.25
0
101~250mm +1.00 631~1000mm +1.4
0
Max. stroke is 1000mm. Contact us for longer strokes.
Double Acting Single Rod Aluminium Tube Ex) ACX-LB350-S500 Basic mass: 410(Foot Ø350) / Additional mass: 24/100 Cylinder stroke: 500mm 410 + 24/100 X 500 = 530 kg
Calculation:
Bellows
Material Max. Temperature
Nil Without bellowsJ Nylon Tarpaulin 60K Neoprene cloth 110
Symbol
Double Acting / Single Rod
Features
Bore size Ø350 to Ø450 is available.
Excellent durability and performance.
Various mounting styles.
Refer to page [1]-133, for specifications about custom-made rod ends.
KCC Co., Ltd.
www.kccpr.com 971 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Extra-Large Cylinder
ACX series
Dimensions-Foot (LB)
Dimensions-Rod Side Flange (FA)
Unit : mm
Bore size A ØD ØEA ØEB ØFD FT FW FX FY FZ KK L N PG
Ø350 90 80 115 175 26 30 110 460 330 510 M72×2.0 200 8-M24×1.5 25
Ø400 100 90 125 196 30 32 120 515 360 575 M82×2.0 225 8-M27×1.5 30
Ø450 110 100 140 215 33 35 120 565 400 630 M90×2.0 240 12-M27×1.5 30
Bore size Rc(PT) T T TL
Ø350 1 225 385 425
Ø400 1 1/4 250 435 475
Ø450 1 1/4 285 485 525
Unit : mm
Bore size A ØD ØEA KK L ØLD LH LS LX LY LT N PG Rc(PT)
Ø350 90 80 115 M72×2.0 200 36 230 410 280 422.5 25 8-M24×1.5 25 1
Ø400 100 90 125 M82×2.0 225 39 295 485 320 512.5 32 8-M27×1.5 30 1 1/4
Ø450 110 100 140 M90×2.0 240 42 320 530 380 562.5 35 12-M27×1.5 30 1 1/4
Bore size T T TL X Y
Ø350 225 385 573 105 43
Ø400 250 435 655 130 50
Ø450 285 485 725 145 55
KCC Co., Ltd.
www.kccpr.com 981 -
PNEUMATIC & HYDRAULIC
Extra-Large Cylinder
ACX series
Unit : mm
Bore size A ØCD CL CX ØD ØEA KK L LR N PG R Rc(PT) T
Ø350 90 63 121 80 80 115 M72×2.0 200 75 8-M24×1.5 25 71 1 225
Ø400 100 71 135 90 90 125 M82×2.0 225 85 8-M27×1.5 30 80 1 1/4 250
Ø450 110 80 150 100 100 140 M90×2.0 240 95 12-M27×1.5 30 90 1 1/4 285
Bore size T TL TZ
Ø350 385 617 546
Ø400 435 690 610
Ø450 485 765 675
Dimensions-Head Side Flange (FB)
Dimensions-Single Clevis (CA)
Unit : mm
Bore size A ØD ØEA ØEB ØFD FT FW FX FY FZ KK L N PG
Ø350 90 80 115 175 26 30 110 460 330 510 M72×2.0 200 8-M24×1.5 25
Ø400 100 90 125 196 30 32 120 515 360 575 M82×2.0 225 8-M27×1.5 30
Ø450 110 100 140 215 33 35 120 565 400 630 M90×2.0 240 12-M27×1.5 30
Bore size Rc(PT) T T TL
Ø350 1 225 385 425
Ø400 1 1/4 250 435 475
Ø450 1 1/4 285 485 525
KCC Co., Ltd.
www.kccpr.com 991 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
ACX seriesExtra-Large Cylinder
Unit : mm
Bore size A ØD ØEA KK L LZ N PG Rc(PT) RR RT T T ØTD TL TX TY TZ
Ø350 90 80 115 M72×2.0 200 100 8-M24×1.5 25 1 4 85 225 385 71 -0.100 425 490 430 640-0.174
Ø400 100 90 125 M82×2.0 225 112 8-M27×1.5 30 1 1/4 4 90 250 435 80 -0.100 475 540 490 720-0.174
Ø450 110 100 140 M90×2.0 240 117 12-M27×1.5 30 1 1/4 4 100 285 485 90 -0.120 525 610 530 800-0.207
Dimensions-Center Trunnion (TC)
Unit : mm
Bore size CF
CT
F J KK L ND NX RA
USingle
knuckle joint
Double knuckle
joint
Single knuckle
joint
Double knuckle
jointØ350 142 110 160 92 30 M72×2.0 205 63 80 276 85 90
Ø400 160 120 180 102 30 M82×2.0 215 71 90 295 90 100
Ø450 180 130 200 112 40 M90×2.0 225 80 100 315 95 120
Unit : mm
Bore size Stroke S A ØEB
Ø350
0-250 186
90 190251-400 216401-630 276
631-1000 356
Ø400
0-250 205
100 220251-400 245401-630 295
631-1000 385
Ø450
0-250 204
110 230251-400 234401-630 294
631-1000 374
Dimensions-Bellows Attached (J) Dimensions-Accessory
Single Knuckle Joint Double Knuckle JointBellows Attached Type (J)
SUS band is mounted at bellows at delivery.
Type J K
Material Nylon Tarpaulin Neoprene Cloth
Heat resistant 60 110
KCC Co., Ltd.
www.kccpr.com 1001 -
PNEUMATIC & HYDRAULIC
Low Friction Cylinder
KLC series
KLC CA - 50 SM - 64
SeriesKLC Low friction cylinder
ActionSM Single actingWM Double acting
Mounting styleCA Single clevis
Cylinder strokeBore size Standard stroke
Ø50 64Ø63 78
Bore size50 ø5063 ø63
Speci cations
KLC series
How to Order
KLC CA-50 SM-64
Symbol
Double Acting / Single Rod
Single Acting /Single Rod
Features
Low friction cylinder.
Bore size: ø50, ø63.
Single clevis mounting style.
Smooth slow movement is possible.
Action Single/Double acting, Single rod
Fluid Clean Air (for 5 Filter & Oil remove filter)
Max. operating pressure 9.0kgf/cm2 (0.9MPa)
Min. operating pressure 0.1kgf/cm2 (0.01MPa)
Ambiet & uid temperature 5 ~ 60
Standard stroke Refer to the standard stroke table above
Internal leakage 1.6 /min
Mounting direction Horizontal
KCC Co., Ltd.
www.kccpr.com 1011 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
KLC seriesLow Friction Cylinder
Unit : mm
Bore size A H T L L1 CT CL ØCD CX C T KK Rc(PT)
Ø50 20 11 45 133 221 8 33 10 16 50 64 M10X1.25 1/4
Ø63 24 10 50 160 260 8 38 12 18 60 80 M12X1.25 1/4
Dimensions
KCC Co., Ltd.
www.kccpr.com 1021 -
PNEUMATIC & HYDRAULIC
Labyrinth Cylinder
KLCS series
Speci cations
KLCS series
How to Order
KLCS CA 50 - 64
SeriesLCS Labyrinth cylinder
Cylinder strokeBore size Ø20 Ø30 Ø40 Ø50 Ø63 Ø80 Ø100Standard
stroke 50 50 50 64 78 108 144
Mounting styleCA Single clevisCB Double clevis
Bore size20 30 40 50 63 80 100
Ø20 Ø30 Ø40 Ø50 Ø63 Ø80 Ø100
KLCS CA 50-64
Symbol
Single Acting / Single Rod
Features
Seal is not applied this ensures smooth
and sensitive movement to minor load variation.
Due to the high ef ciency, almost 100% of the
supply pressure is used as driving force. It is
also applicable with low pressure.
Application
Film winder tension control. Control the tension of textile machinery. To maintain balance of electric servo mechanism.
Action Single acting
Fluid Clean air (for 5 Filter & Oil remove filter)
Max. stroke 300mm
Min. operating pressure 0.02 ~ 0.4kgf/cm2 (0.002 ~ 0.04MPa)
Ambiet & uid temperature -10 ~ 40 (Contact KCC for higher temperature type)
Lubrication Not required (Do not lubricate)
Standard stroke Refer to the standard stroke table above
Internal leakage 300 /min (ANR) (for Ø50 cylinder at 0.4kgf/cm2)
Attachment direction Vertical (within 15° from vertical axis)
KCC Co., Ltd.
www.kccpr.com 1031 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
KLCS seriesLabyrinth Cylinder
Unit : mm
Bore size A B C D E F G H J K L M N P Q R
Ø20 20 5 25 M10X1.25 0 11 21 22 8 12 0 0 38 Rc(PT) 1/8 89 135
Ø30 20 5 25 M10X1.25 0 13 25 26 10 14 0 0 48 Rc(PT) 1/8 124 174
Ø40 20 5 25 M10X1.25 0 14 27 30 10 16 0 0 59 Rc(PT) 1/8 136 188
Ø50 20 6 26 M10X1.25 9 33 47 30 10 16 60 7 78 Rc(PT) 1/4 144 217
Ø63 20 7 30 M10X1.25 10 38 54 35 12 18 70 9 90 Rc(PT) 1/4 143 227
Ø80 23 8 40 M10X1.25 12 44 64 40 15 22 80 9 100 Rc(PT) 1/4 115 219
Ø100 40 8 48 M10X1.25 14 50 68 56 18 26 100 12.5 120 Rc(PT) 1/4 150 266
Dimensions
KCC Co., Ltd.
www.kccpr.com 1041 -
PNEUMATIC & HYDRAULIC
Compact Cylinder
AF/ADF series
AF/ADF series
How to Order
AF - 20 A - S 15
Series
AF Single rod compact cylinder (Without auto switch)
AFW Double rod compact cylinder(Without auto switch)
ADF Single rod compact cylinder(With auto switch)
ADFW Double rod compact cylinder(With auto switch)
CushionNil NoneC Rubber bumperA Air cushion
Custom made type. (Under developement)
Special OrderNil None
TS Multi-step stroke cylinder (Single rod)
TW Multi-step stroke cylinder (Double rod)
ASJ Stroke adjustable type (in forward direction within 10mm)
BSJ Stroke adjustable type (in forward direction within 20mm)
S Single acting spring returnT Single acting spring extend
SV Heat resistant cylinderE Anti-lateral load cylinder
MS Scraper cylinder (Ø32 ~ Ø80)SV Heat resistant cylinderSS Stainless steel piston rod
Number of auto switchesNil 2 pcs1 1 pcN N pcs (N:3,4,5...)
Only for auto switch attached type.
Hole typeA Both end tapped type (Standard)B Through hole type
For Ø12 & Ø16 type, through hole type(B) is standard type.
Type
Nil Single rod, Non-lubricated (Standard)
L Low hydraulic pressure
Rod end threadNil Female thread N Male thread
Mounting styleNil StandardLB FootFA Rod side ange FB Head side angeCB Double clevis
Some of the dimensions of bracket attached type is different with standard type.
Bore size12 Ø12 50 Ø5016 Ø16 63 Ø6320 Ø20 80 Ø8025 Ø25 100 Ø10032 Ø32 125 Ø12532 Ø32 125 Ø12540 Ø40
Symbol
Double Acting /Single Rod
Single Acting /Spring Return
Double Acting /Double Rod
Single Acting /Spring Extend
Features
Ideal for clamping, press-in and under short stroke condition. Can be installed even in a narrow space
with a shorter length in axial thrust direction. Easy installation only with bolts. Excellent appearance after anodizing.
Cylinder strokeAction
Bore sizeStandard stroke
Single rod Double rodØ12
5, 10, 15. 20. 25, 30 5, 10, 15. 20. 25, 30Ø16Ø20
5, 10, 15, 20, 25, 30, 35, 40, 45, 50 5, 10, 15, 20, 25, 30, 35, 40, 45, 50Ø25Ø32 5, 10, 15, 20, 25, 30, 35, 40, 45, 50,
75, 100 5, 10, 15, 20, 25, 30, 35, 40, 45, 50Ø40Ø50
5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 75, 100 5, 10, 15, 20, 25, 30, 35, 40, 45, 50
Ø63Ø80
Ø100Ø125
Refer to page [1]-117, for dimensions of long stroke type (cylinder above standard stroke)
Auto switch
Reed A/S Model Solid state A/S Model
A-72 D-A72K F-7NV D-F7NVKA-73 D-A73K F-7PV D-F7PVKA-80 D-A80K F-7BV D-F7BVKA-90 D-A90(V)K F-9N(V) D-F9N(V)KA-93 D-A93(V)K F-9P(V) D-F9P(V)KA-96 D-A96(V)K F-9B(V) D-F9B(V)K
Only for auto switch attached type. Refer to Auto Switch Catalogue for more
information.
Refer to page [1]-133, for specifications about custom-made rod ends.
KCC Co., Ltd.
www.kccpr.com 1051 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Compact Cylinder
AF/ADF series
Min. Operating Pressure
Bore size Ø12 Ø16 Ø20 Ø25 Ø32 Ø40 Ø50 Ø63 Ø80 Ø100 Ø125
Double acting 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
Single acting (Spring return, Spring extend) 1.5 1.5 1.8 1.8 1.7 1.5 1.3 - - - -
Min. Stroke For Auto Switch Attachment
Number of auto switch Min. stroke
1 pc 5mm
2 pcs 10mm
Only for ADF series(auto switch attached type).
Bore sizeMounting Ø12 Ø16 Ø20 Ø25 Ø32 Ø40 Ø50 Ø63 Ø80 Ø100
Foot LB(CP)12 LB(CP)16 LB(CP)20 LB(CP)25 LB(CP)32 LB(CP)40 LB(CP)50 LB(CP)63 LB(CP)80 LB(CP)100
Flange FA/FB(CP)12 FA/FB(CP)16 FA/FB(CP)20 FA/FB(CP)25 FA/FB(CP)32 FA/FB(CP)40 FA/FB(CP)50 FA/FB(CP)63 FA/FB(CP)80 FA/FB(CP)100Double clevis
(with pin) CB(CP)12 CB(CP)16 CB(CP)20 CB(CP)25 CB(CP)32 CB(CP)40 CB(CP)50 CB(CP)63 CB(CP)80 CB(CP)100
For foot mounting, set (2 pcs) are basic.
Accessory
Mounting Style
Type Double acting single rod
Accessory Standard Foot Rod side ange
Head side ange
Double clevis
Standard Rod end nut
Clevis pin - - - -
OptionSingle knuckle joint
Double knuckle joint
For double clevis and double knuckle joint, pin and snap ring are included. Every mounting bracket includes a hex-wrench bolt. Rod end nut is only applicable to male thread type.
Bore size(mm)Rod end attachment Ø12 Ø16 Ø20 Ø25 Ø32,Ø40 Ø50,Ø63 Ø80 Ø100
Single knuckle joint I(CP)12 I(CP)16 I(CP)20 I(CP)25 I(CP)32,40 I(CP)50,63 I(CP)80 I(CP)100
Double knuckle joint Y(CP)12 Y(CP)16 Y(CP)20 Y(CP)25 Y(CP)32,40 Y(CP)50,63 Y(CP)80 Y(CP)100
Rod end nut RN(CP)12 RN(CP)16 RN(CP)20 RN(CP)25 RN(CP)32,40 RN(CP)50,63 RN(CP)80 RN(CP)100
Rod End Attachment
Speci cationsFluid Air
Proof pressure 15.3kgf/cm2 (1.53MPa)
Max. operating pressure 10.2kgf/cm2 (1.02MPa)
Ambient & uid temperature -10 ~ 70 (No Freezing)
Operating piston speed 50 ~ 500mm/sec
Cushion None(Standard), Rubber bumper, Air cushion
Tolerance of thread KS class 2
Tolerance of stroke +1.00
Rod end thread Female thread, Male thread
For intermediate strokes 55~100, spacer of 5, 10, 20 mm will be used. Example: AF50B-S55 is produced by installing 20mm spacer in AF50B-S75.
Low hydraulic pressure type and standard type have the same dimensions.
KCC Co., Ltd.
www.kccpr.com 1061 -
PNEUMATIC & HYDRAULIC
AF/ADF seriesCompact Cylinder
Auto Switch Attachment
Auto switch mounting screw
Auto switch spacer
Auto switch mounting nut
(M3x0.5x1.0 )
Adjusting screw
Auto switch
Unit : mm
Bore size A B
Ø12 7.5 3
Ø16 7.5 3
Ø20 8 6.5
Ø25 8 6.5
Ø32 9.5 7
Ø40 13.5 9.5
Ø50 13.5 12.5
Ø63 14 15.5
Ø80 17 20
Ø100 21.5 25
Ø125 32.5 32.5
Ø12~Ø25 Ø12~Ø125 (Standard)
Ø20~Ø125
For 5mm stroke cylinder(with 1 auto switch) or 10mm stroke cylinder (with 2 auto switches) when auto switch/auto switches do not turn off or both switches turn on simultaneously, mount the auto switch 1~2mm more toward.
KCC Co., Ltd.
www.kccpr.com 1071 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Unit : g
Cylinder stroke
Bore size
Ø12 Ø16 Ø20 Ø25 Ø32 Ø40 Ø50 Ø63 Ø80 Ø100
5 43 64 94 134 182 269 - - - -
10 49 71 106 149 202 290 455 627 1162 1966
15 55 79 118 164 222 312 488 665 1222 2047
20 61 87 131 180 241 333 521 703 1282 2127
25 67 95 143 195 261 355 554 741 1342 2208
30 73 102 155 210 281 376 587 779 1403 2288
35 - - 167 226 300 398 620 817 1463 2368
40 - - 179 241 320 420 653 855 1524 2449
45 - - 191 256 340 441 686 893 1584 2529
50 - - 203 272 359 463 719 931 1644 2610
75 - - - - 459 575 891 1129 1941 3018
100 - - - - 558 687 1062 1326 2237 3426
Unit : g
Cylinder stroke
Bore size
Ø12 Ø16 Ø20 Ø25 Ø32 Ø40 Ø50 Ø63 Ø80 Ø100
5 50 77 120 170 238 353 - - - -
10 58 87 136 185 260 383 609 798 1393 2334
15 65 96 151 201 283 412 645 840 1469 2443
20 73 106 166 216 306 442 681 882 1546 2551
25 80 115 182 232 329 471 716 924 1622 2660
30 87 125 197 247 352 500 752 966 1699 2769
35 - - 212 263 375 530 788 1008 1775 2877
40 - - 228 279 398 559 823 1051 1851 2986
45 - - 243 294 421 589 859 1093 1928 3094
50 - - 258 310 444 618 895 1135 2004 3203
75 - - - - 558 765 1073 1346 2387 3746
100 - - - - 673 912 1252 1556 2769 4289
Both end tapped 2 2 6 6 6 6 6 19 45 45
Rod end male
thread
Male thread part
1.5 3 6 12 26 27 53 53 120 175
Nut 1 2 4 8 17 17 32 32 49 116Rubber bumper attached
0 0 -2 -3 -3 -7 -9 -18 -31 -56
Foot 55 67 164 186 142 154 243 317 683 1052Rod side
ange 57 69 139 161 180 214 373 559 1056 1365
Head side ange 54 65 133 152 165 198 348 534 1017 1309
Double clevis 32 39 88 123 151 196 393 554 1109 1887
For foot, rod side flange, and head side flange mounting, bolt is included. Double clevis includes a pin, a snap ring and bolt.
Both end tapped 2 2 6 6 6 6 6 19 45 45
Rod end male
thread
Male thread part
3 6 12 24 52 54 106 106 240 350
Nut 2 4 8 16 34 34 64 64 98 232Rubber bumper attached
0 0 -2 -2 -3 -7 -12 -20 -34 -57
Mounting bolt is included for foot, head side flange type.
AF/ADF seriesCompact Cylinder
MassADF Series
ADFW Seires
Unit : g
Cylinder stroke
Bore size
Ø12 Ø16 Ø20 Ø25 Ø32 Ø40 Ø50 Ø63 Ø80 Ø100
5 29 42 63 86 125 187 - - - -
10 35 50 75 100 145 208 339 480 916 1608
15 41 59 88 115 165 230 372 518 976 1688
20 47 67 101 129 184 251 405 556 1036 1768
25 54 76 114 144 204 273 438 594 1097 1849
30 60 84 127 158 224 294 471 632 1157 1929
35 - - 140 173 244 315 504 670 1217 2010
40 - - 152 187 263 337 537 708 127 2090
45 - - 165 202 283 358 570 748 1338 2170
50 - - 178 216 303 380 603 784 1398 2251
75 - - - - 448 552 872 1112 1917 2982
100 - - - - 547 664 1043 1308 2215 3391
Unit : g
Cylinder stroke
Bore size
Ø12 Ø16 Ø20 Ø25 Ø32 Ø40 Ø50 Ø63 Ø80 Ø100
5 42 59 89 119 185 279 - - - -
10 49 68 104 136 212 308 497 646 1149 1960
15 56 77 119 153 235 337 538 682 1225 2068
20 63 86 134 170 257 367 580 718 1302 2177
25 70 95 149 187 280 396 622 754 1378 2286
30 77 104 164 204 303 426 664 790 1455 2394
35 - - 179 221 326 455 705 826 1531 2503
40 - - 194 238 349 484 747 862 1608 2612
45 - - 209 255 372 514 789 899 1684 2720
50 - - 224 272 395 543 830 935 1760 2829
75 - - - - 555 749 1122 1187 2296 3589
100 - - - - 670 896 1331 1368 2678 4132
AF Series
AFW Series
1. AF Ex) AF-CB32A-S20NC
Basic mass: 184 / Both end tapped type: 6 / Rod end male thread: 43 Rubber bumper: -3 / Double clevis: 151 184 + 6 + 43 - 3 + 151 = 381g
1. AFW Ex) AFW-CB32A-S20NC
Basic mass: 257 / Both end tapped type: 6 / Rod end male thread: 86 Rubber bumper: -3 / Double clevis: 180 257 + 6 + 86 - 3 + 180 = 526g
2. ADF Ex) ADF-CB32A-S20NC
Basic mass: 241 / Both end tapped type: 6 / Rod end male thread: 43 Rubber bumper: -3 / Double clevis: 151 241 + 6 + 43 - 3 + 151 = 381g
2. ADFW Ex) ADFW-CB32A-S20NC
Basic mass: 306 / Both end tapped type: 6 / Rod end male thread: 86 Rubber bumper: -3 / Double clevis: 180 306 + 6 + 86 - 3 + 180 = 575g
Calculation:
Calculation:
KCC Co., Ltd.
www.kccpr.com 1081 -
PNEUMATIC & HYDRAULIC AF/ADF seriesCompact Cylinder
Structure
No. Parts MaterialBore size
Ø12 Ø16 Ø20 Ø25 Ø32 Ø40 Ø50 Ø63 Ø80 Ø100 Ø125
11 Piston Packing NBR OPA12 OPA16 OPA20 OPA25 OPA32 OPA40 OPA50 OPA63 OPA80 OPA100 OPA125
12 Rod Packing NBR DYR6K DYR8K DYR10K DYR12K DYR16K DRP16 DRP20 DRP20 DRP25 DRP30 DRP35
13 Tube O-Ring NBR S-10 S-14 S-18 S-22 S-29 S-37 S-46 S-60 S-75 S-95 S-120
Part #9, #10 are only for rubber bumper attached cylinder.
Only for AF series
For both AF/ADF series. For both AF/ADF series
Only for AF series
No. Parts Material Remark
1 Cylinder Tube AL Alloy Hard Anodized Aluminium
2 Piston AL Alloy -
3 Piston RodStainless Steel:ø12~Ø25
Hard Chromium PlatingCarbon Steel:ø32~Ø125
4 Rod CoverBrass:ø12~Ø32
White AnodizingAl Ø40~Ø125
5 Head Cover AL Alloy White Anodizing
6 Snap Ring Spring Steel -
7 Bush Copper -
8 Magnet - Only for Auto Switch Attached type
9 Cushion Damper A Urethane -
10 Cushion Damper B Urethane -
Single Acting Spring Return Single Acting Spring Extend
Single Rod, Double Acting Double Rod, Double Acting
KCC Co., Ltd.
www.kccpr.com 1091 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Structure-Air Cushion Type
With auto switch
With auto switch
Details of A part
No. Parts Material Remark
1 Cylinder Tube AL Alloy Hard Anodized
2 Piston AL Alloy Chromated
3 Piston RodStainless Steel Ø20, Ø25
Carbon Steel Ø32~Ø100, Hard Chrome Plated
4 CollarAL Alloy Ø20~Ø40, Anodized
AL Alloy Casted Ø50~Ø100, Chromated, Painted
5 Retaining Ring Carbon Tool Steel Phosphate coating
6 Bush Bearing Alloy Ø50~Ø100
7 Wear Ring Resin Ø63~Ø100
8 Rod End Nut Carbon Steel -
No. Parts Material Remark
9 Magnet - -
10 Steel BallHigh Carbon
Chrome Bearing Steel
-
11 Check Seal Retainer Brass Electroless Nickel Plated
12 Cushion Needle Stainless Steel
13 Check Seal NBR -
14 Check Gasket NBR -
15 Needle Gasket NBR -
Ø50 ~ Ø100
Ø20 ~ Ø40
AF/ADF seriesCompact Cylinder
11
A part
A part
Rod end male thread
No. Parts MaterialBore size
Ø20 Ø25 Ø32 Ø40 Ø50 Ø63 Ø80 Ø10016 Piston Seal NBR OPA20 OPA25 OPA32 OPA40 OPA50 OPA63 OPA80 OPA100
17 Rod Seal NBR DYR10K DYR12K DYR16K DRP16 DRP20 DRP20 DRP25 DRP30
18 Tube Gasket NBR S18 S22 S29 S37 S46 S60 S75 S95
KCC Co., Ltd.
www.kccpr.com 1101 -
PNEUMATIC & HYDRAULIC
Compact Cylinder
AF/ADF series
Mounting Bolt (Through Hole)
Model C L Set Bolt AF12B - S 5
6.5
25 M3 X 25 l - S 10 30 X 30 l - S 15 35 X 35 l - S 20 40 X 40 l - S 25 45 X 45 l - S 30 50 X 50 l AF16B - S 5
6.5
25 M3 X 25 l - S 10 30 X 30 l - S 15 35 X 35 l - S 20 40 X 40 l - S 25 45 X 45 l - S 30 50 X 50 lAF20B - S 5
7.5
25 M5 X 25 l - S 10 30 X 30 l - S 15 35 X 35 l - S 20 40 X 40 l - S 25 45 X 45 l - S 30 50 X 50 l - S 35 55 X 55 l - S 40 60 X 60 l - S 45 65 X 65 l - S 50 70 X 70 l
AF25B - S 5
9.5
30 M5 X 30 l - S 10 35 X 35 l - S 15 40 X 40 l - S 20 45 X 45 l - S 25 50 X 50 l - S 30 55 X 55 l - S 35 60 X 60 l - S 40 65 X 65 l - S 45 70 X 70 l - S 50 75 X 75 l
AF32B - S 5
9
30 M5 X 30 l - S 10 35 X 35 l - S 15 40 X 40 l - S 20 45 X 45 l - S 25 50 X 50 l - S 30 55 X 55 l - S 35 60 X 60 l - S 40 65 X 65 l - S 45 70 X 70 l - S 50 75 X 75 l - S 75 110 X 110 l
- S 100 135 X 135 lAF40B - S 5
7.5
35 M5 X 35 l - S 10 40 X 40 l - S 15 45 X 45 l - S 20 50 X 50 l - S 25 55 X 55 l - S 30 60 X 60 l - S 35 65 X 65 l - S 40 70 X 70 l - S 45 75 X 75 l - S 50 80 X 80 l - S 75 115 X 115 l
- S 100 140 X 140 l
Model C L Set Bolt AF50B - S 10
12.5
45 M6 X 45 l - S 15 50 X 50 l - S 20 55 X 55 l - S 25 60 X 60 l - S 30 65 X 65 l - S 35 70 X 70 l - S 40 75 X 75 l - S 45 80 X 80 l - S 50 85 X 85 l - S 75 120 X 120 l
- S 100 145 X 145 l AF63B - S 10
14.5
50 M8 X 50 l - S 15 55 X 55 l - S 20 60 X 60 l - S 25 65 X 65 l - S 30 70 X 70 l - S 35 75 X 75 l - S 40 80 X 80 l - S 45 85 X 85 l - S 50 90 X 90 l - S 75 125 X 125 l
- S 100 150 X 150 l AF80B - S 10
15
55 M10 X 55 l - S 15 60 X 60 l - S 20 65 X 65 l - S 25 70 X 70 l - S 30 75 X 75 l - S 35 80 X 80 l - S 40 85 X 85 l - S 45 90 X 90 l - S 50 95 X 95 l - S 75 130 X 130 l
- S 100 155 X 155 l AF100B - S 10
15.5
65 M10 X 65 l - S 15 70 X 70 l - S 20 75 X 75 l - S 25 80 X 80 l - S 30 85 X 85 l - S 35 90 X 90 l - S 40 95 X 95 l - S 45 100 X 100 l - S 50 105 X 105 l - S 75 140 X 140 l
- S 100 165 X 165 l AF125B - S 10
22.9
100 M12 X 100 l - S 15 105 X 105 l - S 20 110 X 110 l - S 25 115 X 115 l - S 30 120 X 120 l - S 35 125 X 125 l - S 40 130 X 130 l - S 45 135 X 135 l - S 50 140 X 140 l - S 75 165 X 165 l
- S 100 190 X 190 l
(Note) Mounting bolt of ADF 1) ADF series body length is 10mm longer than that of AF series. Thus, ADF series required a 10mm longer mounting bolt than that of AF series. Ex) AF 40B - S20 M5X50L ADF 40B - S20 M5X60L
KCC Co., Ltd.
www.kccpr.com 1111 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
AF/ADF seriesCompact Cylinder
Dimensions-Standard Ø12, Ø16, Ø20, Ø25
Unit : mm
Bore sizeWithout magnet (AF) With magnet (ADF)
A B C ØD ØE F FNL PA TL L PA TL
Ø12 17 7.5 20.5 28 10 31.5 10.5 25 15.5 6 32 6 9
Ø16 18.5 8 22 30.5 10 34 12 29 20 8 38 8 10
Ø20 19.5 10.5 24 31.5 10.5 36 14 36 25.5 10 47 8 12
Ø25 22.5 11 27.5 32.5 11 37.5 17.5 40 28 12 52 12 15
Bore size K KK NKK ØO PB ØQ Rc(PT) T TN
Ø12 5 M3X0.5 M5X0.8 3.5 5 6.5 Depth 3.5 M5X0.8 3.5 14
Ø16 6 M4X0.7 M6X1.0 3.5 5.5 6.5 Depth 3.5 M5X0.8 3.5 15.5
Ø20 8 M5X0.8 M8X1.25 5.5 6 9 Depth 7 M5X0.8 4.5 18.5
Ø25 10 M6X1.0 M10X1.25 5.5 5.5 9 Depth 7 M5X0.8 5 22.5
Both End Tapped (Standard)
Unit : mm
Bore size G Q1 ØQ2 R
Ø12 3.5 M4X0.7 6.5 7
Ø16 3.5 M4X0.7 6.5 7
Ø20 7 M6X1.0 9 10
Ø25 7 M6X1.0 9 10
Rod End-Female Thread (Standard)
Rod End-Male Thread
Ø12
Ø12
Ø20 ~ Ø25
Ø20 ~ Ø25
Ø16
Ø16
1
2
KCC Co., Ltd.
www.kccpr.com 1121 -
PNEUMATIC & HYDRAULIC AF/ADF seriesCompact Cylinder
Both End Tapped (Standard)
Dimensions-Standard Ø32~Ø125
Unit : mm
Bore size StrokeWithout
magnet (AF)With magnet
(ADF) A B C ØD ØE F FN K KK NKK ØO PA PB ØQL TL L TL
Ø325
23 30 33 40 23.5 45 34 16 60 13 20.5 14 M8X1.25 M14X1.5 5.511.5 5.5
9 Depth 710~100 10.5 7.5
Ø40 5~100 29.5 36.5 39.5 46.5 23.5 52 40 16 69 13 20.5 14 M8X1.25 M14X1.5 5.5 12 8.5 9 Depth 7
Ø50 5~100 30.5 38.5 40.5 48.5 28.5 64 50 20 86 15 26 18 M10X1.5 M18X1.5 6.8 10.5 10.5 11 Depth 8
Ø63 5~100 36 44 46 54 28.5 77 60 20 103 15 26 18 M10X1.5 M18X1.5 9 15 11 14 Depth 10.5
Ø80 5~100 43.5 53.5 53.5 63.5 35.5 98 77 25 132 21 32.5 22 M16X2.0 M22X1.5 11 18 12.5 17.5 Depth 13.5
Ø100 5~100 53 65 63 75 35.5 117 94 30 156 27 32.5 27 M20X2.5 M26X1.5 11 23 13 17.5 Depth 13.5
Ø125 10~300 83 99 83 75 45 142 114 35 190 30 42 30 M22X2.5 M30X1.5 12.5 24.5 24.5 21.2 Depth 18.4
Bore size Rc(PT) T TN U W Z
Ø32M5X0.8 (5st)
7 28.5 4.5 49.5 14Rc(PT)1/8
Ø40 Rc(PT)1/8 7 28.5 5 57 14
Ø50 Rc(PT)1/4 8 33.5 7 71 18
Ø63 Rc(PT)1/4 8 33.5 7 84 18
Ø80 Rc(PT)3/8 10 43.5 6 104 22
Ø100 Rc(PT)3/8 12 43.5 6.5 123.5 22
Ø125 Rc(PT)3/8 16 58 11 162 32
Depth F
Through holeThrough hole
Through hole
Rod End-Female Thread (Standard)
Rod End-Male Thread
Ø32 ~ Ø125
Ø32 ~ Ø125
1
2
Unit : mm
Bore size G Q1 ØQ2 R
Ø32 7 M6X1.0 9 10
Ø40 7 M6X1.0 9 10
Ø50 8 M8X1.25 11 14
Ø63 10.5 M10X1.50 14 18
Ø80 13.5 M12X1.75 17.5 22
Ø100 13.5 M12X1.75 17.5 22
Ø125 18.4 M14X2.0 21.2 25
KCC Co., Ltd.
www.kccpr.com 1131 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
AF/ADF seriesCompact Cylinder
Dimensions-Foot (LB)
Unit : mm
Bore size StrokeWithout magnet
(AF)With magnet
(ADF) A ØD FN LD LG LH LT LX LY LZ KK NKK T TN X YTL L LS TL L LS
Ø325~50 47.2 23 7
57.2 33 17 23.5 16 20.5 6.6 4 30 3.2 58 57 71 M8X1.25 M14X1.5 17 38.5 11.2 5.875,100 57.2 33 17
Ø405~50 53.7 29.5 13.5
63.7 39.5 23.5 23.5 16 20.5 6.6 4 33 3.2 64 64 78 M8X1.25 M14X1.5 17 38.5 11.2 775,100 63.7 39.5 23.5
Ø5010~50 56.7 30.5 7.5
66.7 40.5 17.5 28.5 20 26 9 5 39 3.2 79 78 95 M10X1.5 M18X1.5 18 43.5 14.7 875,100 66.7 40.5 17.5
Ø6310~50 62.2 36 10
72.2 46 20 28.5 20 26 11 5 46 3.2 95 91.5 113 M10X1.5 M18X1.5 18 43.5 16.2 975,100 72.2 46 20
Ø8010~50 75 43.5 13.5
85 53.5 23.5 35.5 25 32.5 13 7 59 4.5 118 114 140 M16X2.0 M22X1.5 20 53.5 19.5 1175,100 85 53.5 23.5
Ø10010~50 88 53 19
98 63 29 35.5 30 32.5 13 7 71 6 137 136 162 M20X2.5 M26X1.5 22 53.5 23 12.575,100 98 63 29
Bore size : Ø32, Ø40, Ø50, Ø63, Ø80, Ø100
Rod End Male Thread
Unit : mm
Bore sizeWithout magnet
(AF)With magnet
(ADF) A ØD FN LD LG LH LT LX LY LZ KK NKK T TN X YTL L LS TL L LS
Ø12 35.3 17 5 46.3 28 16 10.5 6 9 4.5 2.8 17 2 34 29.5 44 M3X0.5 M5X0.8 13.5 24 8 4.5
Ø16 36.8 18.5 6.5 48.8 30.5 18.5 12 8 10 4.5 2.8 19 2 38 33.5 48 M4X0.7 M6X1.0 13.5 25.5 8 5
Ø20 41.2 19.5 7.5 53.2 31.5 19.5 14 10 12 6.6 4 24 3.2 48 42 62 M5X0.8 M8X1.25 14.5 28.5 9.2 5.8
Ø25 44.7 22.5 7.5 54.7 32.5 17.5 17.5 12 15 6.6 4 26 3.2 52 46 66 M6X1.0 M10X1.25 15 32.5 10.7 5.8
Bore size : Ø12, Ø16, Ø20, Ø25
Rod End Male Thread
KCC Co., Ltd.
www.kccpr.com 1141 -
PNEUMATIC & HYDRAULIC
Rod End Male Thread
Rod End Male Thread
Dimensions-Rod Side Flange (FA)
Bore size : Ø12, Ø16, Ø20, Ø25
Unit : mm
Bore sizeWithout magnet
(AF)With magnet
(ADF) A ØD FD FN FQ FT FX FZ KK NKK T TNTL L TL L
Ø12 30.5 17 41.5 28 10.5 6 4.5 9 25 5.5 45 55 M3X0.5 M5X0.8 13.5 24
Ø16 32 18.5 44 30.5 12 8 4.5 10 30 5.5 45 55 M4X0.7 M6X1.0 13.5 25.5
Ø20 34 19.5 46 31.5 14 10 6.6 12 39 8 48 60 M5X0.8 M8X1.25 14.5 28.5
Ø25 37.5 22.5 47.5 32.5 17.5 12 6.6 15 42 8 52 64 M6X1.0 M10X1.25 15 32.5
Unit : mm
Bore size StrokeWithout
magnet (AF)With magnet
(ADF) A ØD FD FN FQ FT FX FY FZ KK NKK T TNTL L TL L
Ø325~50 40 23
50 33 23.5 16 5.5 20.5 48 8 56 34 65 M8X1.25 M14X1.5 17 38.575,100 50 33
Ø405~50 46.5 29.5
56.5 39.5 23.5 16 5.5 20.5 54 8 62 40 72 M8X1.25 M14X1.5 17 38.575,100 56.5 39.5
Ø5010~50 48.5 30.5
58.5 40.5 28.5 20 6.6 26 67 9 76 50 89 M10X1.5 M18X1.5 18 43.575,100 58.5 40.5
Ø6310~50 54 36
64 46 28.5 20 9 26 80 9 92 60 108 M10X1.5 M18X1.5 18 43.575,100 64 46
Ø8010~50 63.5 43.5
73.5 53.5 35.5 25 11 32.5 99 11 116 77 134 M16X2.0 M22X1.5 20 53.575,100 73.5 53.5
Ø10010~50 75 53
85 63 35.5 30 11 32.5 117 11 136 94 154 M20X2.5 M26X1.5 20 53.575,100 85 63
Bore size : Ø32, Ø40, Ø50, Ø63, Ø80, Ø100
AF/ADF seriesCompact Cylinder
KCC Co., Ltd.
www.kccpr.com 1151 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Dimensions-Head Side Flange (FB)
Bore size : Ø12, Ø16, Ø20, Ø25
Unit : mm
Bore sizeWithout magnet
(AF)With magnet
(ADF) A ØD FD FN FT FV FX FZ KK NKK T TNTL L TL L
Ø12 26 17 37 28 10.5 6 4.5 9 5.5 25 45 55 M3X0.5 M5X0.8 3.5 14
Ø16 27.5 18.5 39.5 30.5 12 8 4.5 10 5.5 30 45 55 M4X0.7 M6X1.0 3.5 15.5
Ø20 32 19.5 44 31.5 14 10 6.6 12 8 39 48 60 M5X0.8 M8X1.25 4.5 18.5
Ø25 35.5 22.5 45.5 32.5 17.5 12 6.6 15 8 42 52 64 M6X1.0 M10X1.25 5 22.5
Bore size : Ø32, Ø40, Ø50, Ø63, Ø80, Ø100
AF/ADF seriesCompact Cylinder
Unit : mm
Bore size StrokeWithout
magnet (AF)With magnet
(ADF) A ØD FD FN FQ FT FX FY FZ KK NKK T TNTL L TL L
Ø325~50 40 23
50 33 23.5 16 5.5 20.5 48 8 56 34 65 M8X1.25 M14X1.5 17 38.575,100 50 33
Ø405~50 46.5 29.5
56.5 39.5 23.5 16 5.5 20.5 54 8 62 40 72 M8X1.25 M14X1.5 17 38.575,100 56.5 39.5
Ø5010~50 48.5 30.5
58.5 40.5 28.5 20 6.6 26 67 9 76 50 89 M10X1.5 M18X1.5 18 43.575,100 58.5 40.5
Ø6310~50 54 36
64 46 28.5 20 9 26 80 9 92 60 108 M10X1.5 M18X1.5 18 43.575,100 64 46
Ø8010~50 63.5 43.5
73.5 53.5 35.5 25 11 32.5 99 11 116 77 134 M16X2.0 M22X1.5 20 53.575,100 73.5 53.5
Ø10010~50 75 53
85 63 35.5 30 11 32.5 117 11 136 94 154 M20X2.5 M26X1.5 20 53.575,100 85 63
Rod End Male Thread
Rod End Male Thread
KCC Co., Ltd.
www.kccpr.com 1161 -
PNEUMATIC & HYDRAULIC
Unit : mm
Bore size StrokeWithout magnet
(AF)With magnet
(ADF) A CD CL CT CV CX CZ ØD FN KK N NKK R T TNTL L TZ TL L TZ
Ø325~50 60 23 50
70 33 60 23.5 10 20 5 14 18 36 16 20.5 M8X1.25 M6XP1.0 M14X1.5 10 7 28.575,100 70 33 60
Ø405~50 68.5 29.5 58.5
78.5 39.5 68.5 23.5 10 22 6 14 18 36 16 20.5 M8X1.25 M6XP1.0 M14X1.5 10 7 28.575,100 78.5 39.5 68.5
Ø5010~50 80.5 30.5 66.5
90.5 40.5 76.5 28.5 14 28 7 20 22 44 20 26 M10X1.5 M8XP1.25 M18X1.5 14 8 33.575,100 90.5 40.5 76.5
Ø6310~50 88 36
84 98 46 84 28.5 14 30 8 20 22 44 20 26 M10X1.5 M10XP1.5 M18X1.5 14 8 33.575,100 98 46
Ø8010~50 109.5 43.5
101.5 119.5 53.5 101.5 35.5 18 38 10 27 28 56 25 32.5 M16X2.0 M12XP1.75 M22X1.5 18 10 43.575,100 119.5 53.5
Ø10010~50 132 53
120 142 63 120 35.5 22 45 13 31 32 64 30 32.5 M20X2.5 M12XP1.75 M26X1.5 22 12 43.575,100 142 63
Unit : mm
Bore sizeWithout magnet
(AF)With magnet
(ADF) A ØD FN CB CD CL CT CV CX CZ KK N NKK R T TNTL L TZ TL L TZ
Ø12 40.5 17 34.5 51.5 28 45.5 10.5 6 9 12 5 14 4 7 5 10 M3X0.5 M4XP0.7 M5X0.8 6 3.5 14
Ø16 43 18.5 37 55 30.5 49 12 8 10 14 5 15 4 10 6.5 12 M4X0.7 M4XP0.7 M6X1.0 6 3.5 15.5
Ø20 51 19.5 42 63 31.5 54 14 10 12 20 8 18 5 12 8 16 M5X0.8 M6XP1.0 M8X1.25 9 4.5 18.5
Ø25 57.5 22.5 47.5 67.5 32.5 57.5 17.5 12 15 24 10 20 5 14 10 20 M6X1.0 M6XP1.0 M10X1.25 10 5 22.5
Dimensions-Double Clevis (CB)
Bore size : Ø12, Ø16, Ø20, Ø25
Bore size : Ø32, Ø40, Ø50, Ø63, Ø80, Ø100
AF/ADF seriesCompact Cylinder
Rod End Male Thread
Rod End Male Thread
KCC Co., Ltd.
www.kccpr.com 1171 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
NKKNKK
øD
TLTL + STROKE + STROKE
L + STROKE + STROKET
2-Cushion needle2-Cushion needle2-M5x0.8 2-M5x0.8 (Port size)(Port size)
FNFN
A
TNTN
H G
Dimensions-With Air Cushion
Unit : mm
Bore size A B C ØD ØE F G H FN K KK L NKK ØO ØQ T TL TN
Ø20 14 36 25.5 10 47 8 15.5 21 12 8 M5X0.8 32 M8X1.25 5.5 9 Depth 7 4.5 36.5 18.5
Ø25 17.5 40 28 12 52 12 17 23 15 10 M6X1.0 36.5 M10X1.25 5.5 9 Depth 7 5 41.5 22.5
Unit : mm
Bore size A B C ØD ØE F FN G H K KK L NKK ØO ØQ Rc(PT) T TL TN U W Z
Ø32 23.5 45 34 16 60 13 20.5 18.5 23 14 M8X1.25 37 M14X1.5 5.5 9 Depth 7 1/8 7 44 28.5 4.5 49.5 14
Ø40 23.5 52 40 16 69 13 20.5 20 28 14 M8X1.25 44 M14X1.5 5.5 9 Depth 7 1/8 7 51 28.5 5 57 14
Ø50 28.5 64 50 20 86 15 26 28.5 31.5 18 M10X1.5 49.5 M18X1.5 6.8 11 Depth 8 1/4 8 57.5 33.5 7 71 18
Ø63 28.5 77 60 20 103 15 26 31 34 18 M10X1.5 55 M18X1.5 9 14 Depth 10.5 1/4 8 63 33.5 7 84 18
Ø80 35.5 98 77 25 132 21 32.5 35.5 39 22 M16X2.0 63.5 M22X1.5 11 17.5 Depth 13.5 3/8 10 73.5 43.5 6 104 22
Ø100 35.5 117 94 30 156 27 32.5 40 43 27 M20X2.5 76 M26X1.5 11 17.5 Depth 13.5 3/8 12 88 43.5 6.5 123.5 22
Bore size : Ø20, Ø25
Rod End Male Thread
øD
T L + STROKE + STROKE
TLTL + STROKE + STROKE
2-Cushion2-Cushion needle needle
(Port size)(Port size)2-2- Rc(PT)Rc(PT)
Z
U
W
øE
K
FNFN
A
TNTN
NKKNKK
KK Depth FKK Depth F
GH
4-ØO Through hole4-ØO Through hole8-ØQ C.B8-ØQ C.B
Bore size : Ø32, Ø40, Ø50, Ø63, Ø80, Ø100
Rod End Male Thread
AF/ADF seriesCompact Cylinder
KCC Co., Ltd.
www.kccpr.com 1181 -
PNEUMATIC & HYDRAULIC AF/ADF seriesCompact Cylinder
Dimensions-Long Stroke Cylinder (AF, ADF)
Unit : mm
Bore size Stroke A ØD ØEB FN L KK NKK PA PB T TL TN
Ø12 35~100 10.5 6 - 9 35 M3X0.5 M5X0.8 10 10 13.5 59 24
Ø16 35~100 12 8 - 10 38 M4X0.7 M6X1.0 10 10 13.5 63.5 25.5
Ø20 75~200 14 10 - 12 41 M5X0.8 M8X1.25 10.5 10.5 14.5 69.5 28.5
Ø25 75~200 17.5 12 17 15 44 M6X1.0 M10X1.25 11 11 15 76.5 32.5
Ø32 125~300 23.5 16 22 20.5 45.5 M8X1.25 M14X1.5 12.5 12.5 17 84 38.5
Ø40 125~300 23.5 16 28 20.5 55 M8X1.25 M14X1.5 14 14 17 93.5 38.5
Ø50 125~300 28.5 20 35 26 55.5 M10X1.5 M18X1.5 14 14 18 99 43.5
Ø63 125~300 28.5 20 35 26 57 M10X1.5 M18X1.5 16.5 16.5 18 100.5 43.5
Ø80 125~300 35.5 25 43 32.5 66 M16X2.0 M22X1.5 19 19 20 119.5 53.5
Ø100 125~300 35.5 30 59 32.5 75.5 M20X2.5 M26X1.5 23 23 22 129 53.5
Ø125 5~300 45 35 35 42 83 M22X2.5 M30X1.5 24.5 24.5 16 141 58
Ø125 type and standard type have the same dimensions. For dimensions not shown in those figures, refer to the standard type.
Rod End-Female Thread (Standard) (Ø12 ~ Ø20)
(Ø20 ~ Ø125)
Rod End-Male Thread (Ø12 ~ Ø20)
(Ø25 ~ Ø125)
KCC Co., Ltd.
www.kccpr.com 1191 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
AF/ADF seriesCompact Cylinder
Dimensions-Double Acting Double Rod (AFW, ADFW)
Unit : mm
Bore sizeWithout magnet (AF) With magnet (ADF)
A B C C ØD ØE F FN KL TL TW L TL TW
Ø20 26 35 63 38 47 75 14 36 36 25.5 10 47 8 12 8
Ø25 29 39 74 39 49 84 17.5 40 40 28 12 52 12 15 10
Bore size K KK NKK ØO PA ØQ Rc(PT) T TN
Ø20 8 M5X0.8 M8X1.25 5.5 10.5 9 Depth 7 M5X0.8 4.5 18.5
Ø25 10 M6X1.0 M10X1.25 5.5 11 9 Depth 7 M5X0.8 5 22.5
Both End Tapped (Standard)
Rod End-Female Thread (Standard)
Rod End-Male Thread
DepthDepth
Through holeThrough hole
Through hole
Ø20 ~ Ø25
Ø20 ~ Ø25
1
2
Unit : mm
Bore size G Q1 ØQ2 R
Ø20 7 M6×1.0 9 10
Ø25 7 M6×1.0 9 10
KCC Co., Ltd.
www.kccpr.com 1201 -
PNEUMATIC & HYDRAULIC AF/ADF seriesCompact Cylinder
Both End Tapped (Standard)
Dimensions-Double Acting Double Rod (AFW, ADFW)
Rod End-Female Thread (Standard)
Rod End-Male Thread
Ø32 ~ Ø125
Ø32 ~ Ø125
Through holeThrough hole
Depth FDepth F
Through holeThrough hole
1
2
Unit : mm
Bore sizeWithout magnet (AF) With magnet (ADF)
A B C ØD ØE F FN K KK NKK ØO PAL TL TW L TL TW
Ø32 30.5 44.5 87.5 40.5 54.5 97.5 23.5 45 34 16 60 13 20.5 14 M8X1.25 M14X1.5 5.5 10.5
Ø40 40 54 97 50 64 107 23.5 52 40 16 69 13 20.5 14 M8X1.25 M14X1.5 5.5 12
Ø50 40.5 56.5 107.5 50.5 66.5 117.5 28.5 64 50 20 86 15 26 18 M10X1.5 M18X1.5 6.8 10.5
Ø63 42 58 109 52 68 119 28.5 77 60 20 103 15 26 18 M10X1.5 M18X1.5 9 15
Ø80 51 71 138 61 81 148 35.5 98 77 25 132 21 32.5 22 M16X2.0 M22X1.5 11 18
Ø100 60.5 84.5 147.5 70.5 94.5 157.5 35.5 117 94 30 156 27 32.5 27 M20X2.5 M26X1.5 11 23
Ø125 83 115 199 83 99 199 45 142 114 35 190 30 42 30 M22X2.5 M30X1.5 12.5 24.5
Bore size ØQ Rc(PT) T TN U W Z
Ø32 9 Depth 7 Rc(PT)1/8 7 28.5 4.5 49.5 14
Ø40 9 Depth 7 Rc(PT)1/8 7 28.5 5 57 14
Ø50 11 Depth 8 Rc(PT)1/4 8 33.5 7 71 18
Ø63 14 Depth 10.5 Rc(PT)1/4 8 33.5 7 84 18
Ø80 17.5 Depth 13.5 Rc(PT)3/8 10 43.5 6 104 22
Ø100 17.5 Depth 13.5 Rc(PT)3/8 12 43.5 6.5 123.5 22
Ø125 21.2 Depth 18.4 Rc(PT)3/8 16 58 11 162 32
Unit : mm
Bore size G Q1 ØQ2 R
Ø32 7 M6X1.0 9 10
Ø40 7 M6X1.0 9 10
Ø50 8 M8X1.25 11 14
Ø63 10.5 M10X1.50 14 18
Ø80 13.5 M12X1.75 17.5 22
Ø100 13.5 M12X1.75 17.5 22
Ø125 18.4 M14X2.0 21.2 25
KCC Co., Ltd.
www.kccpr.com 1211 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
AF/ADF seriesCompact Cylinder
Unit : mm
Bore size Without magnet (AF) With magnet (ADF)
A ØD FN T TNL TL TZ L TL TZ
Ø20 45.5 50 64 69.5 74 88 14 10 12 4.5 18.5
Ø25 51.5 56.5 74 71.5 76.5 94 17.5 12 15 5 22.5
Ø32 53.5 60.5 82 73.5 80.5 102 23.5 16 20.5 7 28.5
Ø40 68.5 76.5 97 89.5 96.5 118 23.5 16 20.5 7 28.5
Ø50 71 79 104.5 91 99 124.5 28.5 20 26 8 33.5
Ø63 78 86 111.5 98 106 131.5 28.5 20 26 8 33.5
Ø80 94.5 104.5 138 114.5 124.5 177 35.5 25 32.5 10 43.5
Ø100 113.5 125.5 157 133.5 145.5 133.5 35.5 30 32.5 12 43.5
Ø125 166 182 244 166 182 244 45 35 42 16 58
For dimensions not shown in these figures, refer to the standard type.
Rod End-Female Thread (Standard) (Ø20 ~ Ø25)
Rod End-Female Thread (Standard) (Ø32 ~ Ø125)
Rod End-Male Thread(Ø20 ~ Ø25)
Rod End-Male Thread (Ø32 ~ Ø125)
Single Rod Multi-Step Stroke Cylinder (TS)
Dimensions-Single Rod Multi-Step Stroke Cylinder (TS)
By integrating two cylinders in series enable back and forth stroke and two-steps control for a doubled output.Ordering notation: A Stroke + Total StrokeEx) 150 + 200 (A Side = 150, B Side = 50)
When B port is supplied with air pressure, A and B strokes reverse.
When both A and C ports are suppl ied with a ir pressure, forward output is doubled.
When C port is supplied with air pressure, rod and B Stroke move forward.
When A port is supplied with air pressure, rod and A Stroke move forward.
KCC Co., Ltd.
www.kccpr.com 1221 -
PNEUMATIC & HYDRAULIC
Unit : mm
Bore size Without magnet (AF) With magnet (ADF)
A ØD FN T TNL TL TZ L TL TZ
Ø20 45.5 54.5 82.5 69.5 78.5 106.5 14 10 12 4.5 18.5
Ø25 51.5 61.5 96.5 71.5 81.5 116.5 17.5 12 15 5 22.5
Ø32 53.5 67.55 110.5 73.5 87.5 130.5 23.5 16 20.5 7 28.5
Ø40 68.5 83.5 125.5 89.5 103.5 146.5 23.5 16 20.5 7 28.5
Ø50 71 87 138 91 107 158 28.5 20 26 8 33.5
Ø63 78 94 145 98 114 165 28.5 20 26 8 33.5
Ø80 94.5 114.5 181.5 114.5 134.5 220.5 35.5 25 32.5 10 43.5
Ø100 113.5 137.5 200.5 133.5 157.5 177 35.5 30 32.5 12 43.5
Ø125 166 198 302 166 198 302 45 35 42 16 58
For dimensions not shown in these figures, refer to the standard type.
Multi-Step Stroke Cylinder (TW)
Dimensions-Multi-Step Stroke Cylinder (TW)
Rod End-Male Thread (Ø20 ~ Ø25)
Rod End-Female Thread (Standard) (Ø20 ~ Ø25)
Rod End-Male Thread (Ø32 ~ Ø125)
Rod End-Female Thread (Standard) (Ø32 ~ Ø125)
Head side assembly. By integrating two cylinders enable back and forth stroke and three steps control.Ordering notation: A Stroke + B StrokeExample) 150 + 50 (A Side = 150, B Side = 50)
When A and B ports are supplied with air pressure, A and B strokes reverse.
When C and D ports are supplied with air pressure, A and B strokes move forward.
When A and C ports are supplied with air pressure, B stroke move forward.
When B and D ports are supplied with air pressure, A stroke move forward.
AF/ADF seriesCompact Cylinder
KCC Co., Ltd.
www.kccpr.com 1231 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Unit : mm
Bore size ØC L MI MT MK ML MT T TL
Ø20 20 26 36 8 10 12.5 8 4.5 61
Ø25 20 29 36 8 10 12.5 8 5 64.5
Ø32 27 30.5 Ø38 6 14 16 6 7 72.5
Ø40 27 40 Ø46 6 14 16 6 7 82
Ø50 35 40.5 Ø57 8 16 20 8 8 91.5
Ø63 35 42 Ø68 10 16 20 10 8 95
Ø80 48 51 Ø90 12 20 28 12 10 119
Ø100 48 60.5 Ø110 14 20 28 14 12 134.5
Ø125 - 83 - - - - - 16 -
For dimensions not shown in these figues, refer to the AF series standard type.
Dimensions-Forward Stroke Adjustable (ASJ, BSJ)
Forward Stroke Adjustable Cylinder (ASJ, BSJ)
AF/ADF seriesCompact Cylinder
To adjust the entire forward stroke from 0mm to 20mm an adjustment mechanism is attached to the head side.
ASJ : 0~10mm adjustmentBSJ : 0~20mm adjustmentRange of adjustment
KCC Co., Ltd.
www.kccpr.com 1241 -
PNEUMATIC & HYDRAULIC AF/ADF seriesCompact Cylinder
Dimensions-Anti-Lateral Load (E) - AF, ADF
Unit : mm
Bore size Stroke A ØD ØEB FN ØEB L KK NKK PA PB T TL TN
Ø12 5~30 10.5 6 - 9 - 35 M3X0.5 M5X0.8 10 10 13.5 48.5 24
Ø16 5~30 12 8 - 10 - 38 M4X0.7 M6X1.0 10 10 13.5 51.5 25.5
Ø20 5~50 14 10 - 12 - 41 M5X0.8 M8X1.25 10.5 10.5 14.5 55.5 28.5
Ø25 5~50 17.5 12 17 15 17 44 M6X1.0 M10X1.25 11 11 15 59 32.5
Ø32 5~100 23.5 16 22 20.5 22 45.5 M8X1.25 M14X1.5 12.5 12.5 17 62.5 38.5
Ø40 5~100 23.5 16 28 20.5 28 55 M8X1.25 M14X1.5 14 14 17 72 38.5
Ø50 5~100 28.5 20 35 26 35 55.5 M10X1.5 M18X1.5 14 14 18 73.5 43.5
Ø63 5~100 28.5 20 35 26 35 57 M10X1.5 M18X1.5 16.5 16.5 18 75 43.5
Ø80 5~100 35.5 25 43 32.5 43 66 M16X2.0 M22X1.5 19 19 20 86 53.5
Ø100 5~100 35.5 30 59 32.5 59 75.5 M20X2.5 M26X1.5 23 23 22 97.5 53.5
Ø125 5~300 45 35 35 42 35 83 M22X2.5 M30X1.5 24.5 24.5 16 99 58
Ø125 type and standard type have the same dimensions. For dimensions not shown in those figures, refer to the standard type.
Rod End-Female Thread (Standard) (Ø12 ~ Ø20)
(Ø20 ~ Ø125)
Rod End-Male Thread (Ø12 ~ Ø20)
(Ø25 ~ Ø125)
KCC Co., Ltd.
www.kccpr.com 1251 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
AF/ADF seriesCompact Cylinder
Dimensions-Scraper Attached Cylinder (MS)
Unit : mm
Bore sizeWithout magnet
(AF)With magnet
(ADF) T TNL
Ø32 23 33 7 28.5
Ø40 29.5 39.5 12 33.5
Ø50 30.5 40.5 13 38.5
Ø63 36 46 13 38.5
Ø80 43.5 53.5 15 48.5
For dimensions not shown in those figures, refer to the standard type.
Rod End-Female Thread (Standard)
Rod End-Male Thread - (AF, ADF)
Heat resistant cylinder can be used at a high ambient temperature up to150 by equipped with heat-resistant seal.
Type Non lubricated
Bore size Ø40, Ø50, Ø63, Ø80, Ø100
Temperature -20~150
Packing Material VITON
Stainless steel cylinder rod is selected to prevent the end of rod from corrosion when it is in contact with water during operation.
Type Lubricated, Non lubricated
Bore size Ø40, Ø50, Ø63, Ø80, Ø100
Rod Material SUS304
Stainless Steel Piston Rod (SS)Head Resistant Cylinder (SV)
Speci cations Speci cations
KCC Co., Ltd.
www.kccpr.com 1261 -
PNEUMATIC & HYDRAULIC
Unit : mm
Part no. Bore size A B C E ØG MM MI ØTDH10 TX
I(CP)12 Ø12 21.5 16 2.5 7 12 M5X0.8 6 5 +0.048 0 5 -0.2
-0.4
I(CP)16 Ø16 32 25 3 14 14 M6X1.0 8 5 +0.048 0 6.4 -0.2
-0.4
I(CP)20 Ø20 34 25 4 11.5 18 M8X1.25 8.5 8 +0.058 0 8 -0.2
-0.4
I(CP)25 Ø25 41 30 5 14 23 M10X1.25 10.5 10 +0.058 0 10 -0.2
-0.4
I(CP)32,40 Ø32,40 42 30 6 14 29 M14X1.5 14 10 +0.058 0 18 -0.3
-0.5
I(CP)50,63 Ø50,63 56 40 6.5 20 36 M18X1.5 18 14 +0.070 0 22 -0.3
-0.5
I(CP)80 Ø80 71 50 8 27 38 M22X1.5 21 18 +0.070 0 28 -0.3
-0.5
I(CP)100 Ø100 79 55 10 31 44 M26X1.5 21 22 +0.084 0 32 -0.3
-0.5
Unit : mm
Part no. Bore size A B C E ØG MM MI ØTDH10 TX TY TZ
Y(CP)12 Ø12 21.5 16 6 7 - M5X0.8 6 5 +0.048 0 5 -0.4
-0.2 10 14.6
Y(CP)16 Ø16 28 21 8 10 - M6X1.0 7 5 +0.048 0 6.4 -0.4
-0.2 12 16.6
Y(CP)20 Ø20 34 25 9.5 11.5 16 M8X1.25 8.5 8 +0.058 0 8 -0.4
-0.2 16 21
Y(CP)25 Ø25 41 30 14 14 20 M10X1.25 10.5 10 +0.058 0 10 -0.4
-0.2 20 25.6
Y(CP)32,40 Ø32,40 42 30 - 14 - M14X1.5 16 10 +0.058 0 18 -0.5
-0.3 36 41.6
Y(CP)50,63 Ø50,63 56 40 - 20 - M18X1.5 20 14 +0.070 0 22 -0.5
-0.3 44 50.6
Y(CP)80 Ø80 71 50 - 27 - M22X1.5 23 18 +0.070 0 28 -0.5
-0.3 56 64
Y(CP)100 Ø100 79 55 - 31 - M26X1.5 24 22 +0.084 0 32 -0.5
-0.3 64 72
Unit : mm
Part no. Bore size ØDd9 L1 L2 P W B Retaining ring
CJP(CP)12 Ø12 5 -0.03-0.06 2.5 7 12 M5X0.8 6 Type C 5 for axis
CJP(CP)16 Ø16 5 -0.03-0.06 3 14 14 M6X1.0 8 Type C 5 for axis
CJP(CP)20 Ø20 8 -0.04-0.076 4 11.5 18 M8X1.25 8.5 Type C 8 for axis
CJP(CP)25 Ø25 10 -0.04-0.076 5 14 23 M10X1.25 10.5 Type C 10 for axis
CJP(CP)32,40 Ø32,40 10 -0.04-0.076 6 14 29 M14X1.5 14 Type C 10 for axis
CJP(CP)50,63 Ø50,63 14 -0.05-0.076 6.5 20 36 M18X1.5 18 Type C 14 for axis
CJP(CP)80 Ø80 18 -0.05-0.093 8 27 38 M22X1.5 21 Type C 18 for axis
CJP(CP)100 Ø100 22 -0.065-0.117 10 31 44 M26X1.5 21 Type C 22 for axis
Unit : mm
Part no. Bore size d J A C
RN(CP)12 Ø12 M5X0.8 4 8 9.2
RN(CP)16 Ø16 M6X1.0 5 10 11.5
RN(CP)20 Ø20 M8X1.25 5 13 15
RN(CP)25 Ø25 M10X1.25 6 17 19.6
RN(CP)32,40 Ø32,40 M14X1.5 8 22 25.4
RN(CP)50,63 Ø50,63 M18X1.5 11 27 31.2
RN(CP)80 Ø80 M22X1.5 13 32 37.0
RN(CP)100 Ø100 M26X1.5 16 41 47.3
Dimensions-Accessory
Material: Carbon Steel
Material: Carbon Steel Material: Carbon Steel
Material: Carbon Steel Material: Carbon Steel
Single Knuckle Joint
Double Knuckle Joint
Knuckle Joint Pin / Clevis Pin Rod End Nut
AF/ADF seriesCompact Cylinder
Material: Cast Iron
KCC Co., Ltd.
www.kccpr.com 1271 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Compact Guide Cylinder
AFG series
AFG series
AFGM-12-S30
Bore size (mm)Non-rotating accuracy
AFGM AFGLØ12
±0.07° ±0.10°Ø16Ø20
±0.06° ±0.09°Ø25Ø32
±0.06° ±0.08°Ø40Ø50
±0.05° ±0.06°Ø63Ø80
±0.04° ±0.05°Ø100
Non-Rotating Load Capability
Features
Built in magnet and rubber bumper (Standard).
Resists lateral loading and provides non-
rotating motion.
Sliding bearing and ball bearing are available
depending on applications.
Symbol
Double Acting / Single Rod
AFG M - 12 - S 30
How to Order
As to intermediate stroke (5, 10, 15, 20...), spacer of 5, 10, 15, 20mm width will be used.
Speci cations
SeriesAFG Compact guide cylinder
BearingM Sliding bearingL Ball bearing
Number of auto switchesNil 2 pcs1 1 pcN N pcs (N:3,4,5...)
Only for auto switch attached type.
Bore size12 Ø12 40 Ø4016 Ø16 50 Ø5020 Ø20 63 Ø6325 Ø25 80 Ø8032 Ø32 100 Ø100
Auto switch
Reed A/S Model Solid state A/S Model
Nil None Nil NoneA-72 D-A72K F-7NV D-F7NVKA-73 D-A73K F-7PV D-F7PVKA-80 D-A80K F-7BV D-F7BVK
Refer to Auto Switch Catalogue for more information.
Cylinder strokeBore size Standard stroke
Ø1210, 20, 30, 40, 50, 75, 100
Ø16Ø20
20, 30, 40, 50, 100Ø25Ø32
25, 50, 75, 100, 125, 150
Ø40Ø50Ø63Ø80
Ø100
Ex) AFGM20-S25 is produced by installing 5mm spacer in AFGM20-S30.
ActionDouble acting
Ø12, Ø16 Ø25 ~ Ø100
Fluid Air
Proof pressure 15kgf/cm2(1.5MPa)
Max. operating pressure 10kgf/cm2(1.0MPa)
Min. operating pressure 1.2kgf/cm2(0.12MPa) 1.0kgf/cm2(0.1MPa)Ambient & uid
temperature 5 ~ 60
Operating piston speed 50 ~ 500mm/s
Cushion Rubber bumper
Lubrication Not required
Tolerance of stroke +1.50
KCC Co., Ltd.
www.kccpr.com 1281 -
PNEUMATIC & HYDRAULIC
Compact Guide Cylinder
AFG series
Part no. Parts Material Remark
1 Rod Cover Aluminium Alloy White Alumite
2 Head Cover Aluminium Alloy White Alumite
3 Cylinder Tube Aluminium Alloy White Alumite
4 Piston (C) Aluminium Alloy -
5 Piston (R) Aluminium Alloy -
6 RodStainless Steel Ø12~Ø25
Carbon Steel Ø32~Ø100
7 Guide RodAFGM Carbon Steel Hard Chromium
PlatingAFGL Bearing Steel -
8 Plate Carbon Steel Nikel Plating
9 Urethane Damper Urethane -
Structure
Part no. Parts Material Remark
10 Urethane Damper (C) Urethane -
11 Spacer Carbon Steel -
12 Rod Packing NBR -
13 Tube O-Ring NBR -
14 Magnet Synthetic Rubber -
15 Piston Packing NBR -
16 Plate Mounting Bolt Carbon Tool Steel -
17 Snap Ring (A) Carbon Tool Steel Phosphate Coating
18 Snap Ring (B) Carbon Tool Steel Phosphate Coating
19 Sliding Bearing - -
20 Ball Bearing - -
Unit : kg
Bore size (mm)
Standard stroke - AFGM(Sliding bearing)10 20 25 30 40 50 75 100 125 150
Ø12 0.24 0.28 - 0.31 0.35 0.39 0.50 0.60 - -Ø16 0.35 0.40 - 0.45 0.51 0.55 0.70 0.82 - -Ø20 - 0.71 - 0.79 0.87 0.97 1.15 1.34 - -Ø25 - 1.04 - 1.14 1.25 1.35 1.73 2.00 - -Ø32 - - 1.81 - - 2.20 2.58 2.98 3.39 3.78Ø40 - - 1.91 - - 2.50 2.72 3.31 3.82 4.13Ø50 - - 3.40 - - 3.96 4.52 5.06 5.63 6.19Ø63 - - 3.93 - - 4.55 5.15 5.77 6.39 7.01Ø80 - - 6.99 - - 7.92 88.82 9.74 10.67 11.58
Ø100 - - 11.04 - - 12.35 13.65 14.98 16.31 17.64
Unit : kg
Bore size (mm)
Standard stroke - AFGL(Ball bearing)10 20 25 30 40 50 75 100 125 150
Ø12 0.24 0.26 - 0.30 0.35 0.39 0.48 0.56 - -Ø16 0.35 0.38 - 0.43 0.53 0.59 0.68 0.80 - -Ø20 - 0.72 - 0.80 0.91 0.99 1.18 1.35 - -Ø25 - 1.05 - 1.15 1.32 1.43 1.71 1.91 - -Ø32 - - 1.53 - - 1.87 2.29 2.65 3.01 3.37Ø40 - - 1.69 - - 2.04 2.50 2.86 3.22 3.58Ø50 - - 2.83 - - 3.31 3.91 4.40 4.89 5.38Ø63 - - 3.47 - - 4.00 4.66 5.20 5.74 6.28Ø80 - - 5.54 - - 6.43 8.00 8.84 9.68 10.52
Ø100 - - 10.27 - - 11.46 13.71 14.89 16.07 17.26
Mass
KCC Co., Ltd.
www.kccpr.com 1291 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Compact Guide Cylinder
AFG series
Unit : mm
Bore size A B C CA CB D
DADB E EA
EB
AFGM AFGL
AFGM AFGL 30ST 30ST~ 50ST 50ST 10ST 20ST 30ST 40ST, 50ST 50ST
Ø12 26 60 13 12.5 13 6 8 6 46 8 5 0 5 34 3 13 13 23 28
Ø16 30 67 15 14.5 15 8 10 8 50 8 5 0 5 34 5 20 20 30 35
Ø20 36 85 18 17.5 18 10 12 10 58 10 6 3 5 47 - 12 25 35 45
Ø25 42 95 21 20.5 21 12 16 13 68 10 6 3 5 47 - 18 18 37 48
Dimensions-Ø12 ~ Ø25 / AFGM, AFGL
Bore size F
FAFB FC FD FL FH FM FLL GA GB GC GD GM GL LA LB
30ST 30ST
Ø12 7 20 40 25 4.3 8 13.5 18 M5XP0.8 12 18 50 23 M3 M4XP0.7 10 29 42
Ø16 7 24 44 27 4.3 8 12.5 22 M5XP0.8 12 22 56 24 M3 M5XP0.8 12 33 46
Ø20 18 24 44 31 5.5 9.5 13.5 24 M5XP0.8 13 24 72 28 M5 M5XP0.8 13 37 53
Ø25 18 24 44 35 5.5 9.5 14.5 30 M6XP1.0 15 30 82 34 M5 M6XP1.0 15 37.5 53.5
Bore size
LL
P PA PB QA QB QM R S UU UA UB UC UDAFGM AFGL
30ST 30ST~ 50ST 50ST 10SST 20ST 30ST 40ST, 50ST 50ST
Ø12 42 47 76 45 55 55 65 70 M5XP0.8 11 8.5 14 48 M4XP0.7 58 22 23 3 3.5 3 6
Ø16 46 51 80 51 66 66 76 81 M5XP0.8 11 8 16 54 M5XP0.8 65 25 24 3 3.5 3 6
Ø20 56 58 100 - 65 78 88 95 Rc(PT) 1/8 10.5 9 18 70 M5XP0.8 83 30 28 3 3.5 3 6
Ø25 56.5 58.5 100.5 - 71.5 71.5 90.5 101.5 Rc(PT) 1/8 11.5 9.5 26 78 M6XP1.0 93 38 34 4 4.5 3 6
For intermediate stroke, spacer will be used.
KCC Co., Ltd.
www.kccpr.com 1301 -
PNEUMATIC & HYDRAULIC AFG seriesCompact Guide Cylinder
Unit : mm
Bore size A B C CA CB D
DAE EA
EB
AFGM AFGL
AFGM AFGL 25ST 50ST 75ST 100ST 125ST 150ST 25ST 50ST 75ST 100ST 125ST 150ST
Ø32 53 114 27 25 26 16 20 16 12 10 23.2 41.2 46.2 46.2 51.2 51.2 4.4 41.4 46.4 46.4 66.4 66.4
Ø40 57 124 31 25 26 16 20 16 12 10 16.7 34.7 39.7 39.7 44.7 44.7 0 34.9 39.9 39.9 59.9 59.9
Ø50 69 140 39 29 30 20 25 20 16 12 27.7 39.7 49.7 49.7 54.7 54.7 2.9 44.9 49.9 49.9 69.9 69.9
Ø63 82 150 45.5 29 36.5 20 25 20 16 12 22.7 34.7 44.7 44.7 49.7 49.7 0 39.9 44.9 44.9 64.9 64.9
Dimensions-Ø32 ~ Ø63 / AFGM, AFGL
Bore size P PA PB QA QB QM R S SA SB T TA TB TL TM U UA UB UC UL
Ø32 1/8 12.5 9 30 96 M8XP1.25 112 48 2 1 16 5 100 11 M8XP1.25 42 4 4.5 3 6
Ø40 1/8 14 10.5 30 106 M8XP1.25 122 48 2 1 17 10 110 11 M8XP1.25 50 4 4.5 3 6
Ø50 1/4 14 11 40 120 M10XP1.5 138 56 2 1 17 10 124 12.5 M10XP1.5 56 5 6 4 8
Ø63 1/4 16.5 13.5 50 130 M10XP1.5 148 69 2 0 19 10 132 15 M10XP1.5 66 5 6 4 8
For intermediate stroke, spacer will be used.
Bore size GA GB GL GM I LA LB
LL
AFGM AFGL
25ST 50ST 75ST 100ST 125ST 150ST 25ST 50ST 75ST 100ST 125ST 150ST
Ø32 38 80 20 M8XP1.25 22 37.5 59.5 82.7 100.7 105.7 105.7 110.7 110.7 63.9 100.9 105.9 105.9 125.9 125.9
Ø40 38 90 20 M8XP1.25 22 44 66 82.7 100.7 105.7 105.7 110.7 110.7 63.9 100.9 105.9 105.9 125.9 125.9
Ø50 44 100 25 M10XP1.5 22 44 72 99.7 111.7 121.7 121.7 126.7 126.7 74.9 116.9 121.9 121.9 141.9 141.9
Ø63 44 110 25 M10XP1.5 31 49 77 99.7 111.7 121.7 121.7 126.7 126.7 74.9 116.9 121.9 121.9 141.9 141.9
KCC Co., Ltd.
www.kccpr.com 1311 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
AFG seriesCompact Guide Cylinder
Unit : mm
Bore size A B C CA CB D
DAE EA
EB
AFGM AFGL
AFGM AFGL 25ST 50ST 75ST, 100ST 125ST, 150ST 25ST, 50ST 75ST, 100ST, 125ST, 150ST
Ø80 96.5 204 50 38.5 46.5 25 30 25 22 18 23.3 25.3 53.3 58.3 8.5 72.5
Ø100 114.5 238 58 41 56.5 30 36 30 25 20 18.8 23.8 48.8 53.8 4.0 73
Dimensions-Ø80 ~ Ø100 / AFGM, AFGL
Bore size P PA PB PC QA QB QM R S SA SB T TA TB TL TM
Ø80 3/8 19 15.2 28 60 174 M12XP1.75 198 80 6.5 10 20.5 15.5 182 18 M12XP1.75
Ø100 3/8 22.5 18.8 35 64 200 M14XP2.0 231 95 9 10.5 20.5 25 211 21 M14XP2.0
For intermediate stroke, spacer will be used.
Bore size F FA FB FC FD FL GA GB GL GM LA LB
LL
AFGM AFGL
25ST 50ST 75ST ,100ST 125ST ,150ST
25ST
,50ST75ST, 100ST, 125ST, 150ST
Ø80 20.5 15.5 100 11 17.5 11 56 155 30 M12XP1.75 56.5 96.5 119.8 121.8 149.8 154.8 105 169
Ø100 20.5 25 120 13 20 13 62 184 35 M14XP2.0 66 111 129.8 134.8 159.8 164.8 115 184
KCC Co., Ltd.
www.kccpr.com 1321 -
PNEUMATIC & HYDRAULIC
Free Mount Cylinder
FM/FMD series
FM/FMD series
How to Order
FM - 20 - S 15 D
Series
FM Single rod without magnetfree mount cylinder
FMD Single rod with built-in magnetfree mount cylinder
ActionD Double acting
Number of auto switchesNil 2 pcs1 1 pcN N pcs (N:3,4,5...)
Only for auto switch attached type.
Port type
Nil M5×0.8(Ø32 : Rc(PT) 1/8)
G G 1/8 (Only for Ø32)
Bore size6 Ø6
10 Ø1016 Ø1620 Ø2025 Ø2532 Ø32
Symbol
Double Acting /Single Rod
Features
With non-lubricated seal (Standard). The multiple surface direct mounting with a
square body enables spacesaving designs for equipment.
Cylinder strokeBore size Standard stroke
Ø65, 10, 15, 20, 25, 30Ø10
Ø16Ø20
5, 10, 15, 20, 25, 30, 40, 50Ø25
Ø30
Auto switchReed A/S Model Solid
state A/S Model
A-90 D-A90(V)K F-9N(V) D-F9N(V)KA-93 D-A93(V)K F-9P(V) D-F9P(V)KA-96 D-A96(V)K F-9B(V) D-F9B(V)K Only for auto switch attached type. Refer to Auto Switch Catalogue for more
information.
Speci cations Tightening Torque
Bore size (mm) Screw dia. Proper tightening torque(N m)
Ø6, Ø10 M3 1.08±10%
Ø16 M4 2.45±10%
Ø20, Ø25 M5 5.10±10%
Ø16 M6 8.04±10%
Refer to page [1]-133, for specifications about custom-made rod ends.
Bore size Ø6 Ø10 Ø16 Ø20 Ø25 Ø32
Fluid Air
Proof pressure 10.5kgf/cm2 (1.05MPa)
Max. operating pressure 7kgf/cm2 (0.7MPa)
Min. operating pressure 1.2kgf/cm2 (0.12MPa)
0.6kgf/cm2 (0.06MPa) 0.5kgf/cm2 (0.05MPa)
Ambient & uid temperature 5 ~60
Operating piston speed 50 ~ 500mm/s
Cushion Rubber bumper
Lubrication Not required
Tolerance of thread KS class 2
Tolerance of stroke +1.00
Rod end thread Male thread (Standard)
FM-20-S15D
KCC Co., Ltd.
www.kccpr.com 1331 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
FM/FMD seriesFree Mount Cylinder
Structure
Part no. Parts Material
1 Cylinder Tube Aluminium Alloy
2 Head Cover Brass, Aluminium Alloy
3 Piston (A) Brass, Aluminium Alloy
4 Piston (R) Brass, Aluminium Alloy
5 Piston (C) Aluminium Alloy
6 Piston Rod Stainless Steel
7 Dumper Urethane
8 Snap Ring Carbon Tool Steel
Part no. Parts Material
9 Rod End Nut Carbon Steel
10 Bush Sintered Alloy
11 Rod Packing NBR
12 Piston Packing NBR
13 Tube O-Ring NBR
14 Magnet -
15 Rod O-Ring NBR
FM10~32 (Without magnet) FMD10~32 (With built-in magnet)
FM6 (Without magnet) FMD6 (With built-in magnet)
MassFMDUnit : g
Cylinder stroke (mm)
Bore size (mm)
Ø6 Ø10 Ø16 Ø20 Ø25 Ø32
5 22 36 50 95 176 262
10 25 40 56 106 193 286
15 28 44 62 117 210 310
20 31 48 68 128 227 334
25 34 52 74 139 244 358
30 37 56 80 150 261 382
40 - - - 172 295 430
50 - - - 194 329 478
Unit : g
Cylinder stroke (mm)
Bore size (mm)
Ø6 Ø10 Ø16 Ø20 Ø25 Ø32
5 27 41 75 128 230 335
10 35 50 86 143 252 364
15 38 54 92 154 269 388
20 41 58 98 165 286 412
25 44 62 104 176 303 436
30 47 66 110 187 320 460
40 - - - 209 354 508
50 - - - 231 388 556
FM
KCC Co., Ltd.
www.kccpr.com 1341 -
PNEUMATIC & HYDRAULIC FM/FMD seriesFree Mount Cylinder
Dimensions
Unit : mm
Bore size A A' B C D E GA GB H J K L MM
Ø6 7 - 13 22 3 7 15 10 13 10 17 - M3×0.5
Ø10 10 - 15 24 4 7 16.5 10 16 11 18 - M4×0.7
Ø16 11 12.5 20 32 6 7 16.5 11.5 16 14 25 5 M5×0.8
Ø20 12 14 26 40 8 9 19 11 18.7 16 30 6 M6×1.0
Ø25 15.5 18 32 50 10 10 21.5 13 23 20 38 8 M8×1.25
Ø32 19.5 22 40 62 12 11 23 12.5 27 24 48 10 M10×1.25
Bore size NN P Q QA R TWithout
magnet (FM)With magnet
(FMD)S Z S Z
Ø6 M3×0.5 Depth5 3.2 - - 7 6 Depth 4.8 33 46 33 46
Ø10 M3×0.5 Depth5 3.2 - - 9 6 Depth 5 36 52 36 52
Ø16 M4×0.7 Depth6 4.5 4 2 12 7.6 Depth 6.5 30 46 40 56
Ø20 M5×0.8 Depth8 5.5 9 4.5 16 9.3 Depth 8 36 54.7 46 64.7
Ø25 M5×0.8 Depth8 5.5 9 4.5 20 9.3 Depth 9 40 63 50 73
Ø32 M6×1.0 Depth9 6.6 13.5 4.5 24 11 Depth11.5 42 69 52 79
Ø6, Ø10
Ø16, Ø20, Ø25, Ø32
Unit : mmBore size KK T H C Qty
Ø6 M3×0.5 1.8 5.5 6.4 2
Ø10 M4×0.7 2.4 7 8.1 2
Ø16 M5×0.8 4 8 9.2 1
Ø20 M6×1.0 5 10 11.5 1
Ø25 M8×1.25 5 13 15.0 1
Ø32 M10×1.25 6 17 19.6 1
Material: Carbon steel
Rod End Nut
KCC Co., Ltd.
www.kccpr.com 1351 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Rod Ends for Pneumatic Cylinder
Custom-Made Rod Ends
- × KA1Pneumatic Cylinder Model Code
KA1 KA2KA0
KA4 KA5KA3
KA7KA6
KA10 KA9
KA13KA12
KA16KA15
KA8
KA11
KA14
KA17
Radius
1. For some products dotted line parts may not exist. 2. For dimensional tolerances and end finishings not shown in these figures will be process according to KCC regulation. 3. " * " is dimension of rod diameter(D) after chamfering. Inform KCC if there is dimension change. Following are standard dimension. D 6 D-1mm 6<D 25 D-2mm D>25 D-4mm
Custom-Made Rod Ends
D
KCC Co., Ltd.
www.kccpr.com 1361 -
PNEUMATIC & HYDRAULIC
Rod Ends for Pneumatic Cylinder
Custom-Made Rod Ends
KA19 KA20KA18
KA22 KA23KA21
KA25KA24
KA28KA27
KA31KA30
KA34KA33
KA26
KA29
KA32
4-sideChamfering
KCC Co., Ltd.
www.kccpr.com 1371 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Tie Rod for Pneumatic Cylinder
Custom-Made Tie Rod
Custom-Made Tie Rod
CT2 (ACM Series)CT1 (ACM Series)
CT3 (ACL Series)
Pneumatic Cylinder Model Code - CT1
KCC Co., Ltd.
www.kccpr.com 1381 -
PNEUMATIC & HYDRAULIC KBP seriesBooster Cylinder
KBP - PP 150 / 125 - 120 H - A54
How to Order
KBP series
TypeDI Direct pressure typePP Pre-pressure type
SeriesKBP Booster cylinder
Bore size Oil pressure Stroke Output oil capacity
Boosting ratio
10080 80kgf/cm2 (8MPa)
12059cm3(cc) 1:16
55 55kgf/cm2 (5.5MPa) 84cm3(cc) 1:1140 40kgf/cm2 (4MPa) 115cm3(cc) 1:8
150
180 180kgf/cm2 (18MPa)
120
59cm3(cc) 1:36125 125kgf/cm2 (12.5MPa) 84cm3(cc) 1:2590 90kgf/cm2 (9MPa) 115cm3(cc) 1:1870 70kgf/cm2 (7MPa) 150cm3(cc) 1:14
125 125kgf/cm2 (12.5MPa)200
141cm3(cc) 1:2590 90kgf/cm2 (9MPa) 192cm3(cc) 1:1870 70kgf/cm2 (7MPa) 251cm3(cc) 1:14
300
180 180kgf/cm2 (18MPa)120
235cm3(cc) 1:36125 125kgf/cm2 (12.5MPa) 339cm3(cc) 1:2570 70kgf/cm2 (7MPa) 603cm3(cc) 1:14180 180kgf/cm2 (18MPa)
200392cm3(cc) 1:36
125 125kgf/cm2 (12.5MPa) 565cm3(cc) 1:2570 70kgf/cm2 (7MPa) 1005cm3(cc) 1:14
Ø300 only available for pre-pressure type. Standard type with aluminium diecast cover and U packing.
For AC4C made cover and Quardring packing, consult KCC.
Auto switchNil NoneH With built-in magnet
Built-in magnet is inapplicable to Ø300 type. Auto switch is attaching on tie rod of
pneumatic cylinder. Select a hydraulic cylinder(KP70/140HC)
with piston compact seal, without cushion for booster.
KBP-PP-150 / 125-120KBP-DI-100 / 80-120
Symbol
Features
System converts air to high oil pressure for high prower applications. High output of air pressure, up to 8~36
times is available and can be integrated with hydraulic equipment.
1. The booster cylinder must be installed higher than the hydraulic actuator and pipes to prevent air release and reverse flow of hydraulic fluid.2. With a slight increase in pressure by mere 0.1kgf/cm2 at the supply side, the output will multiply depending on the sending ratio. Care must be taken.3. If rapid speed is required, the pipe size must be large enough for the purpose, and a quick exhaust valve should be installed.4. A filter and regulator should be installed before the air valve to ensure easy pressure adjustment and clean air supply.5. The discharge volume of the booster cylinder should be the same as the actual capacity of the cylinder.
PrecautionsSpeci cationsWorking oil Petroleum based fluid
Ambient & uid temperature 5~60
Air pressure
Working uid Air
Lubrication Not requiredOperating pressure 0~7kgf/cm2 (0~0.7MPa)
Auto switchReed A/S Model Solid
state A/S Model
Nil None Nil NoneA54 D-A54K F59 D-F59KA56 D-A56K F5P D-F5PKA64 D-A64K J59 D-J59K
A90(V) D-A90(V)K J51 D-J51KA93(V) D-A93(V)K F9N D-F9N(V)KA96(V) D-A96(V)K F9P D-F9P(V)K
F9B D-F9B(V)K Only for auto switch attached type. Refer to Auto Switch Catalogue for more
information.
KCC Co., Ltd.
www.kccpr.com 1391 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
KBP seriesBooster Cylinder
Circuit
Direct Compressed TypeTo be used if the discharge volume is being specified.
Pre-compressed TypeIf the stroke of the hydraulic actuator is long, or large flow is required, the pre-compressed type is used to enable rapid movement to the pressure section by air, and then to pressurize using the discharge volume.
1. Rapid Feed Stroke Cylinder rod is moved to a certain distance by the hydraulic pressure which has the same pressure as the air pressure pass through solenoid valve 1 when solenoid is ON.
2. Pressure Stroke The booster piston is pressurized by the solenoid valve 2 generating high hydraulic pressure required in various processes (clamping, press and etc).
3. Return Stroke Booster Piston and the cylinder pistons are returned by the solenoid valve 1 and 2.
KCC Co., Ltd.
www.kccpr.com 1401 -
PNEUMATIC & HYDRAULIC KBP seriesBooster Cylinder
Structure
5
Part no. Parts Material Remark
1 Rod Cover Aluminium Alloy -
2 Head Cover Aluminium Alloy -
3 Cylinder Tube Aluminium -
4 Piston Aluminium Alloy -
5 Rod Carbon Steel Hard Chromium Plating
6 Tube Carbon Steel -
7 LB Ass'y Zinc Plate -
8 Tie Rod Carbon Steel -
9 Oil Tank Aluminium -
KCC Co., Ltd.
www.kccpr.com 1411 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
KBP seriesBooster Cylinder
Dimensions-Ø100, Ø150
Unit : mm
Bore size ØD L LH LS LX LY LZ N T TL
Ø100 Ø100 55 70 80 138 160 (197) Ø6.5 28 105
Ø150 Ø150 31 110 61 180 200 (258) Ø7 28 105
Dimensions-Ø300 Pre-Pressure
Air-hydro convertor is sold separately.
Air-hydro convertor is sold separately.
Direct Pressure (KBP-DI)
Pre-Pressure (KBP-PP)
KCC Co., Ltd.
www.kccpr.com 1421 -
PNEUMATIC & HYDRAULIC CCTS seriesAir-Hydro Converter
CCTS - 63 - 100
How to Order
CCTS series
SeriesCCTS Air-hydro converter
Bore size
Bore sizeConverter
nominal size (mm)
Air port size Oil port size
63 Ø63 Rc(PT)3/8 Rc(PT)3/4100 Ø100 Rc(PT)1/2 Rc(PT)3/4160 Ø160 Rc(PT)3/4 Rc(PT)3/4
Stroke50, 100, 150, 200, 250, 300, 400, 450, 500, 600, 700, 800
Contact us for other stroke.
Converter nominal size
(mm)
Standard effective oil level stroke (mm) Limited ow /min50 100 150 200 250 300 400 500 600 700 800
Ø63 150 300 450 600 740 890 1190 1480 1780 - - 36
Ø100 370 750 1120 1510 1870 2260 3010 3770 4520 - - 88
Ø160 - 1830 - 3660 - 5490 7320 9150 10980 12810 14640 217
Symbol
Features
It converts air pressure to equivalent hydraulic pressure. The hydraulic pressure is used to operate an actuator. It solves the sticking and slipping problems
with low speed operations.
Speci cations
Fluid Turbine Oil (40~100mm2/S)
Proof pressure 10.5kgf/cm2 (1.05MPa)
Operating pressure 0~7kgf/cm2 (0~0.7MPa)
Ambient & uid temperature 5 ~ 50
KCC Co., Ltd.
www.kccpr.com 1431 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
CCTS seriesAir-Hydro Converter
Dimensions
Unit : mm
Type Air port Oil port A B C 4-ØM D E F G H I
Ø63 Rc(PT)3/8 Rc(PT)3/4 105 87 64 8.5 88 45 86 3 53 30
Ø100 Rc(PT)1/2 Rc(PT)3/4 152 127 95.5 13 136 72 130 7 63 36
Type J K N O 4-P Q R 4-S T U 4-V Y
Ø63 7 2 72 36 M5×0.8 - - - - - - 28
Ø100 7 8 72 36 M5×0.8 85 32.5 M5×0.8 100 40 M6×1.0 35
Stroke L 50 100 150 200 250 300 400 500 600 700 800
Ø63 245 295 345 395 445 495 595 695 795 - -Ø100 255 305 355 405 455 505 605 705 805 - -Ø160 - 272 - 412 - 552 662 802 922 1042 1152
CCTS 63, 100 CCTS 160
Air port size Rc(PT)
Oil draining hole
Oil port sizeRc(PT) 3/4 Oil draining hole Oil port size
Air port Rc(PT) 3/4
Mounting hole
KCC Co., Ltd.
www.kccpr.com 1441 -
PNEUMATIC & HYDRAULIC CCTS seriesAir-Hydro Converter
Application Circuit
1) Dual Speed Control Circuit
The standard covalence and transformation circuits are used, and both directions of the cylinder are controlled.
Application - Feed at low or constant velocity - Cutting motion of machine tools - Valve open/close - Vertically moving load - Industrial machinery - Woodworking machine and etc
2) Rotary Cylinder Circuit
The Rotary Cylinder Circuit controls speed of the rotary cylinders. The foregoing cylinder is added to a rotary cylinder to enable various circuit configurations. A connection valve is installed to compensate the leakage inside the rotary cylinder.
Application - Industrial robots - Conveyor - Paint equipment - Valve open/close - Turntable
3) Intermediate Stop Circuit
This is used for reliable intermediate stopping.
Application - Spot welding machine - Machine tool - Valve open/close
4) Locking Circuit
This is used for intermediate stopping in forward and reverse movements. Even the pneumatic source is blocked, this circuit ensures a reliable locking.
Application - Valve open/close - Vertical moving load - Welding machine
Key points in applying circuit design Dual circuit as the standard circuit
A converter is fitted at the rod side and at the head side of cylinder each, to prevent air inflow on occurrence of leak at the cylinder piston packing, and this is applied as the standard circuit.
Meter-out circuit control The assembly will control the oil that is returned from a cylinder to a converter.
Flow Rate Setup Select the pipe, nipples and assembly to satisfy the required flow.
Cautions in cylinder selection The cylinder must be of the low pressure type. (G or L type) There is a magnet integrated type too. (Switch is sold separately)
KCC Co., Ltd.
www.kccpr.com 1451 -
PNEUMATIC & HYDRAULIC
Pneumatic Cylinder
Reference Data
AJP
KGUA
ACP
ACD
ACS2
ACS3
ACS4
ACS5
ACR
ACM
ACL
ACX
KLC
KLCS
AF, ADF
AFG
FM, FMD
Custom-Made
Rod EndsCustom-
Made Tie Rods
KBP
CCTS
Application Circuit
5) Low Speed Stable Circuit
This is an example of 5~10 filters being fitted in front and rear of a throttle valve in order to facilitate stable movement at low speed and to prevent any adverse effect of foreign materials in the hydraulic fluid. The throttle valve should be in V-groove shape.There is a case where hydraulic fluid of high viscosity is stably used at 10mm/min.If the cylinder speed is less than 40mm/min, use this control circuit.
Application - Cutting motion of machine tool - Medical device - Feed system in industrial machinery - Camera processing machine - Semi-conductor manufacturing equipment - Testing devices
6) 2 Stage-Speed Control Circuit
The circuit for 2 stage-speed transmission for rapid feed and cutting feed, enables a step feed, multiple program-transmissions when fitted with solenoid and throttle valves, and absorbing of impact during switching when fitted with mechanical valves.
Application - Cutting feed of machine tool - Butterfly valve open/close - cushioning device
7) Synchronising Circuit
The synchronising circuit is used to synchronise multiple cylinders. If the cylinder rods are connected, synchronising is satisfactory; if they are not connected, synchronising is poor after the air valve is being switched. The cushion packing must be removed with this circuit.
Application - Vertical table feed - Arm synchronising - Lifter - Extruder
8) Impact Prevention Circuit
This is used for shock absorbers and on the spot where impact is being made by falling weights.
Application - Lifter - Conveyor - Packing machine - Dental lab equipment
9) Auxiliary Circuit for Booster This is used for RAM return in air-hydro boosters.
Application - Dental lab equipment - Mold
CCTS seriesAir-Hydro Converter