030 vios install sea

8/8/2019 030 Vios Install Sea

1/33

Copyright IBM Corporation 2007 Course materials may not be reproduced in whole or in part without written permission.

Installing the VIO Server LPAR from NIMQPS01 IBM System P APV 030


2/33

Copyright IBM Corporation 2007

IBM System p

QPS01 030 VIOS Install SEA 2

IBM System p Advanced POWER Virtualization

Defining VIO Server Partition

Objectives: Describe how to activate partition to go to SMS mode

SMS mode is used for installing AIX and Linux

Describe how to setup SMS menus for network NIM install

Install the VIO server LPAR from NIM

Select language for install Select disks to be used for install


3/33


IBM System p



Partition Definition Handout Use your handout

VIO hostname

VIO IP

VIO Install NIM Server

NetmaskGateway

Spanning Tree

Adapter speed


4/33 Copyright IBM Corporation 2007

IBM System p



Select the Partition(s) to Activate

1. ODD Right click

on VIO1 partition

1. EVEN Right clickon VIO2 partition

2. Select Activate

from popup window.


5/33


IBM System p



Select the Partition Profile you want to activate

default

4. Select

Open a terminal window..

5. Select

Advanced

3. Select

Desired default profile

Do not click OK yet


6/33


IBM System p



Select Boot Mode for the Partition

6. Select

Boot Mode Dropdown

7. Select SMS


7/33


IBM System p



Exit advanced menu and start partition

Partition activation starts

8. Click OK

default

9. Click OK


8/33


IBM System p



Activation ends and installation begins

Observe Activate Windows

Click Show Details if desired

To select this console as the active console press 0

Press 0 if prompted


9/33


IBM System p



Last chance to enter SMS mode

IBM IBM IBM IBM IBM IBM IBM IBM IBM IBM IBM IBM IBM IBM IBM IBM IBM





1 = SMS Menu 5 = Default Boot List

8 = Open Firmware Prompt 6 = Stored Boot List

Memory Keyboard Network SCSI Speaker

If you had not specified to boot to SMS, you would need to wait for thisscreen to pop up and then hit 1 repeatedly as the bottom line is displaying

This only appears for a couple of seconds, so it is very easy to miss it

It is much more convenient to use the SMS override from the advanced

activation menu


10/33


IBM System p



SMS Main Menu => Select Remote IPL

Main Menu

1. Select Language

2. Setup Remote IPL (Initial Program Load)

3. Change SCSI Settings

4. Select Console

5. Select Boot Options

Type menu item number and press Enter or select Navigation key: 2

-------------------------------------------------------------------------------------------NIC Adapters

Device Location Code Hardware

Address1. Interpartition Logical LAN U9111.520.1007F4F-C2-T1 2646c00050022. Interpartition Logical LAN U9111.520.1007F4F-C3-T1 2646c0005003

3. Port 1 IBM 2 PORT 10/100 U787A,001,DPM1672-P1-T5 00096beb8122

4. Port 2 IBM 2 PORT 10/100 U787A,001,DPM1672-P1-T6 00096beb8122


Type 2 and press Enter

To select

Setup Remote IPL


Adapter on Port 1

Do NOT select

Interpartition Logical LAN


11/33


IBM System p



Select set IP Parameters

Network Parameters

Port 1 IBM 2 PORT 10/100 U787A,001,DPM1672-P1-T5

1. IP Parameters

2. Adapter Configuration3. Ping Test

4. Advanced Setup: BOOTP


-------------------------------------------------------------------------------------------


To select

IP Parameters


12/33


IBM System p



Set the Client IP Address

IP Parameters


1. Client IP Address [000.000.000.000]

2. Server IP Address [000.000.000.000]3. Gateway IP Address [000.000.000.000]

4. Subnet Mask [255.255.255.000]


-------------------------------------------------------------------------------------------

X to Abort or Enter Client IP Address: 10.31.197.XX


EnterVIO IP addressFrom student worksheet

And press Enter


13/33


IBM System p



Set the NIM Server IP Address

IP Parameters


1. Client IP Address [10.31.197.XX]]


4. Subnet Mask [255.255.255.000]


-------------------------------------------------------------------------------------------

X to Abort or Enter Client IP Address: 10.31.197.164


Enter IP address

of NIM server

10.31.197.164

And press Enter


14/33


IBM System p



Set the Subnet Mask

IP Parameters




4. Subnet Mask [255.255.255.000]


-------------------------------------------------------------------------------------------

X to Abort or Subnet mask: 255.255.240.0


Enter subnet mask

255.255.240.0

And press Enter


15/33


IBM System p



Verify settings

IP Parameters




4. Subnet Mask [255.255.240.000]


Press Esc Once

Verify

No XX | No XX

01 13 | 02 17

03 23 | 04 27

05 33 | 06 37

07 43 | 08 47

09 53 | 10 57

11 63 | 12 67

13 73 | 14 77

15 83 | 16 87

17 93 | 18 97

19 103 | 20 107

21 113 | 22 117

23 123 | 24 127

25 133 | 26 137

27 143 | 28 147

29 153 | 30 157

IBM S t Ad d POWER Vi t li ti


16/33


IBM System p



Enter 2 to set Adapter Configuration

Network Parameters


1. IP Parameters




-------------------------------------------------------------------------------------------


To select

Adapter Configuration

IBM S t Ad d POWER Vi t li ti


17/33


IBM System p



Enter 1 to set Speed Duplex



1. Speed,Duplex

2. Spanning Tree Enabled3. Protocol


-------------------------------------------------------------------------------------------

Spanning Tree Enabled


1. auto, auto ( rj45 )>


18/33


IBM System p



Enter 2 to set Spanning Tree Enable to No



1. Speed,Duplex

2. Spanning Tree Enabled3. Protocol


-------------------------------------------------------------------------------------------



1. Yes

2. No


To select


Type 2 and press EnterforNo

Press Esc twice



19/33


IBM System p



Enter 3 to set Ping Test

Network Parameters


1. IP Parameters




-------------------------------------------------------------------------------------------

Type 3 and press Enter to select Ping Test



20/33


IBM System p



Verify configuration and execute ping test

Ping Test

Interpartition Logical LAN: U9111.520.1007F4F-V7-C5-T1

Speed, Duplex: auto.auto

Client IP Address: 10.31.197.XX

Server IP Address: 10.31.197.164

Gateway IP Address: 000.000.000.000

Subnet Mask: 255.255.240.0

Protocol: Standard

Spanning Tree Enabled: 0

Connector type: rj45

1. Execute ping test


Type 1 and press Enter to

Execute Ping Test

verify PING SUCCESS



21/33


IBM System p



Enter M to return to Main Menu

Network Parameters

Interpartition Logical LAN: U9111.520.1007F4F-V7-C5-T1

1. IP Parameters

2. Adapter Configuration

3. Ping Test


Type menu item number and press Enter or select Navigation key: M

-------------------------------------------------------------------------------------------

Type M to return to Main Menu



22/33


IBM System p



Select Boot Options -> Select Install/Boot Device

Main Menu

1. Select Language

2. Setup Remote IPL (Initial Program Load)

3. Change SCSI Settings4. Select Console

5. Select Boot Options


-------------------------------------------------------------------------------------------

Multiboot

1. Select Install/Boot Device

2. Configure Boot Device Order3. Mutliboot Startup



To select

Select Boot Options


Select Install/Boot Device



23/33


IBM System p


y p

Select Device Type Network => Choose ethernet slot

Select Device Type1. Diskette

2. Tape

3. CD/DVD

4. IDE

5. Hard Drive6. Network

7. List all devices


-------------------------------------------------------------------------------------------

Select DeviceDevice Current Device

Number Position Name1. 2 Virtual Ethernet

( loc=U9111.520.1007F4F-V5-C2-T1

2. 2 Virtual Ethernet

( loc=U9111.520.1007F4F-V5-C3-T1

3. - Ethernet

( loc=U787A.001.DPM1672-P1-T5

4. - Ethernet

( loc=U787A.001.DPM1672-P1-T6



To select

Network


forPort 1 Ethernet



24/33


IBM System p


y p

Normal Mode Boot => Exit SMS

Ethernet

( loc=U4787A.001.DPM1672-P1-T5

1. Information

2. Normal Mode Boot3. Service Mode Boot


-------------------------------------------------------------------------------------------

Are you sure you want to exit System Management Services?

1. Yes

2. No



To select

Normal Mode Boot


forYes



25/33


IBM System p


The Partition(s) boot from BOOTP/TFTP

BOOTP: client IP = 10.31.197.XX

BOOTP: client HW addr = 0 9 6b eb 81 22

BOOTP: gateway IP = 0.0.0.0

BOOTP: device /pci@80000000200000002/pci@2,4/ethernet@1

BOOTP: loc-code U787A.001.DPM1672-P1-T5

BOOTP R = 1 BOOTP S=2

FILE: /tftpboot/sys01_vio1

BOOTP: chose-network-type = ethernet,auto, rj45,auto

BOOTP server IP = 10.31.197.164

BOOTP: requested filename =BOOTP: client IP = 10.31.197.XX

BOOTP: client HW addr = 0 9 6b eb 81 22

BOOTP: gateway IP = 0.0.0.0

BOOTP: device /pci@80000000200000002/pci@2,4/ethernet@1

BOOTP: loc-code U787A.001.DPM1672-P1-T5

BOOTP R = 1 BOOTP S = 2

FILE: /tftpboot/sys01_vio1icmp 5 : redirect

Packet Count 3100

If BOOTP fails

Notify instructor now

Look for FILE name

Watch packet count



26/33


IBM System p


Define System Console / English Install

********* Please define the System Console ********

Type a 1 and press Enter to use this terminal as the system console

>>> Type 1 and press Enter to have English during install

Type the number of your choice and press Enter. Choice is indicated by >>>

>>> 1 Start Install Now with Default Settings2 Change/Show Installation Settings and Install

3 Start Maintenance Mode for System Recover

>

Type 1 and press EnterforSystem Console


forEnglish

Type 2 to select

Change/Show



27/33


IBM System p


Verify the Disk Selection

Installation and Settings

Either Type 0 and press Enter to install with current settings, or type the

number of the setting you want to change and press Enter

Setting: Current Choice(s):

1. Disk(s) where you want to install ...hdisk0...

Use Maps ....................No

2. Shrink File Systems .................No

3. Import User Volume Groups ...........No

4. Recover Devices .....................No

>>> 0 Install with the settings listed above

88 Help ?

99 Previous Menu

>>> Choice [0]: 1

Type 1 and Enter

hdisk0 show more than 1 disk



28/33


IBM System p


Make sure both disks are selected

Change Disk(s) Where You Want to Install

Type one or more numbers for the disk(s) to be used for installation and press

Enter. To cancel a choice, type the corresponding number and Press Enter.

At least one bootable disk must be selected. The current choice is indictedby >>>.

Name Location Code Size(MB) VG Status Bootable No

>>> 1 hdisk0 03-08-00-3,0 70006 rootvg Yes No

2 hdisk1 03-08-00-4,0 70006 rootvg Yes No

>>> 0 Continue with choices indicated above55 More Disk Options

66 Disks not known to Base Operating System Installation

77 Display Alternative Disk Attributes

88 Help ?99 Previous Menu

>>> Choice [0]: 77 .


>>> shows selected disks

Type number to select/unselect

Install to both disks

Press 2 if hdisk1 isnot selected.



29/33


IBM System p



View Physical Volume Identifier




Name Physical Volume Identifier

>>> 1 hdisk0 00c07f6fbc7639c8

>>> 2 hdisk1 00c07f6f5a0a2e18

>>> 0 Continue with choices indicated above55 More Disk Options

66 Disks not known to Base Operating System Installation



>>> Choice [0]: 77 .

Type 77 Enter

PVID indicates disk was used

before.



30/33


IBM System p



View Physical Volume Identifier




Name Device Adapter Connection Location

or Physical Location Code

1 hdisk0 U787A.001.DPM166C-P1-T10-L3-L0

2 hdisk1 U787A.001.DPM166C-P1-T10-L4-L0

>>> 0 Continue with choices indicated above55 More Disk Options66 Disks not known to Base Operating System Installation



>>> Choice [0]:.

Press Enter

View SCSI adapter location

Example slot T10



31/33


IBM System p


Verify the Disk Selection

Installation and Settings

Either Type 0 and press Enter to install with current settings, or type the

number of the setting you want to change and press Enter

Setting: Current Choice(s):

1. Disk(s) where you want to install ...hdisk0

Use Maps ....................No

2. Shrink File Systems .................No

3. Import User Volume Groups ...........No

4. Recover Devices .....................No

>>> 0 Install with the settings listed above

88 Help ?

99 Previous Menu

>>> Choice [0]: 0

Type 0 and Enter

Press Enter on next prompts

to begin install

Last chance to back out before

writing to the disks



32/33


IBM System p


The system will reboot once installed

Installing Base Operating System

Please wait. . .

Approximate Elapsed time

% tasks complete (in minutes)

96 21 Creating boot image

The system will reboot after the installation and perform post-install tasksdefined on the NIM server (firstboot scripts, etc)

Monitor installation progress



33/33


IBM System p


Summary

Described how to activate partition to go to SMS mode

SMS mode is used for installing AIX and Linux

Described how to setup SMS menus for network NIM install

Installed the VIO server LPAR from NIM Select language for install

Select disks to be used for install

030 vios install sea

Documents