08-miscelaneo-catalogo productos final 2016 v2 liv

8/18/2019 08-Miscelaneo-Catalogo Productos Final 2016 v2 Liv

1/100

Catalogo de

Productos2016


2/100

ESPECIFICACIONES TECNICAS:• Extintor portátil capacidad 1 kilo presión interna.• Polvo Químico Seco multipropósito al 40% (Fosfato Monoamonico).• Certicado Cesmec.• Para el combate de fuegos clase ABC.• Rating apague de 1 – A: 2 – B: C.

ESPECIFICACIONES TECNICAS:

• Extintor portátil capacidad 2 kilos presión interna.• Polvo Químico Seco multipropósito al 40%.

• Certicado Cesmec.• Para el combate de fuegos clase ABC.• Rating de apague de 2 – A: 5 – B C.• Incluye soporte.

EXTINTOR PORTATIL 1 KILO PQS

ESPECIFICACIONES TECNICAS:• Extintor portátil capacidad 4 kilospresión interna.• Polvo Químico Seco multipropósito al 40%.• Certicado Cesmec.• Para el combate de fuegos clase ABC.• Rating de apague de 6 – A: 30 – B C.• Incluye soporte.




3/100


• Extintor portátil capacidad 6 kilos presión interna.• Polvo Químico Seco multipropósito al 40%.• Certicado Cesmec.• Para el combate de fuegos clase ABC.• Rating de apague de 10 – A: 40 – B C.• Incluye soporte.


• Extintor portátil capacidad 10 kilos presión interna.• Polvo Químico Seco multipropósito al 40%.• Certicado Cesmec.• Para el combate de fuegos clase ABC.

• Rating de apague de 10 – A: 40 – B C.• Incluye soporte.




4/100

Mangueras PQS de 4 a10 kg :

Mangueras CO2 de 5 kg:

Toberas Co2 de 2 kg:

Abrazaderas:

manometros:

valvulas:

repuestos de extintores PQS y CO2


5/100


• Extintor portátil capacidad 2 kilos• Procedencia RPC• Dióxido de Carbono (CO²)• Certicado Cesmec• Para el combate de fuegos clase BC• Rating de apague 2 – B : C• Incluye soporte


• Extintor portátil capacidad 5 kilos.• Procedencia RPC.• Dióxido de Carbono (CO²).• Certicado Cesmec.• Para el combate de fuegos clase BC.

• Rating de apague 2 – B : C.• Incluye soporte.

EXTINTOR PORTATIL 2 KILOS DIOXIDO DE CARBONO ( CO2 )

EXTINTOR PORTATIL 5 KILOS DIOXIDO DE CARBONO ( CO2 )


6/100

EXTINTOR PORTATIL ACETATO DE POTASIO 6 LITROSLos extintores de químicos húmedos son los mejores extintores portátiles paracocinas de restaurantes y aprobados por la nueva Clase K enlistada por la ULespecícamente para accidentes de cocinas en restaurantes. Contiene una baseespecial de acetato de potasio, un agente de bajo PH desarrollado para el uso ensistemas de pre-ingeniería de cocinas para restaurantes. La existencia actual deaparatos de cocina más complejos y el uso de aceites no saturados, dictan el usode extintores portátiles con mayor capacidad para combatir el fuego y el efectode enfriamiento para combatir estos difíciles y calientes incendios.

EXTINTOR PORTATIL ACETATO DE POTASIO 10 LITROSLos extintores de químicos húmedos son los mejores extintores portátiles

para cocinas de restaurantes y aprobados por la nueva Clase K enlistadapor la UL especícamente para accidentes de cocinas en restaurantes.Contiene una base especial de acetato de potasio, un agente de bajo PHdesarrollado para el uso en sistemas de pre-ingeniería de cocinas pararestaurantes. La existencia actual de aparatos de cocina más complejos yel uso de aceites no saturados, dictan el uso de extintores portátiles conmayor capacidad para combatir el fuego y el efecto de enfriamiento paracombatir estos difíciles y calientes incendios.


7/100

EXTINTOR PORTATIL ACETATO DE POTASIO 6 LITROSESPECIFICACIONES TECNICAS:Naturaleza del Agente : Espuma mecánicaNombre químico: AFFF / ARContenido porcentual nominal del compuesto activo: 3%Potencial de extinción: 2-A :10 -BContenido nominal : 6 ltsMasa aprox. cargado: 9,2 kgMasa aprox. Descargado: 3,2 kg

EXTINTOR PORTATIL ACETATO DE POTASIO 10 LITROSESPECIFICACIONES TECNICAS:Naturaleza del Agente : Espuma mecánicaNombre químico: AFFF / ARContenido porcentual nominal del compuesto activo: 3%Potencial de extinción: 4-A : 20 -BContenido nominal : 10 ltsMasa aprox. cargado: 14,2 kgMasa aprox. Descargado: 4,2 kg


8/100

RED LINE cartridge-operated re extinguishers are the premiumreghting units preferred by safety directors worldwide in high

re-risk industries such as chemical, petro-chemical, oil and gas,mining, aviation, and power generation. Cartridge-operatedmeans increased reliability, on-the-spot recharge, ease of servi-ce, and superior reghting performance. Typical applications include fuel loading racks, heavy construc-tion sites, dip tanks, oil pumping stations, mining equipment,paint lockers, trucks and buses, fuel storage rooms, production

lines and others. Tough, carbon steel shells resist impact, vibra-tion and corrosion; quality components stand up to years ofservice; and special polyester powder paints provide superiorprotection against cracking and chipping.

EXTINTOR PORTATIL ACETATO DE POTASIO 6 LITROS

Carro Rodante PQS 25 KgESPECIFICACIONES TECNICAS:Naturaleza del Agente : Polvo Químico SecoMultipropósitoNombre químico: Fosfato mono amónicoContenido porcentual nominal del compuestoactivo: 90%

Potencial de extinción: 40-A : 60 - B :CContenido nominal : 25 kg


9/100

Carro Rodante PQS 25 Kg

ESPECIFICACIONES TECNICAS:Naturaleza del Agente :Polvo Químico Seco Multipropósito

Nombre químico: Fosfato mono amónicoContenido porcentual nominal del compuestoactivo: 90%Potencial de extinción: 40-A : 80-B:CContenido nominal : 50 kgMasa aprox. cargado: 86,6 kg

ESPECIFICACIONES TECNICAS:Naturaleza del Agente : Polvo Químico Seco MultipropósitoNombre químico: Fosfato mono amónicoContenido porcentual nominal del compuesto activo: 90%Potencial de extinción: 40-A : 60 - B :CContenido nominal : 25 kgMasa aprox. cargado: 55,7 kgMasa aprox. Descargado: 30,7 kg

Carro Rodante PQS 100 KgESPECIFICACIONES TECNICAS:Naturaleza del Agente : Polvo Químico Seco MultipropósitoNombre químico: Fosfato mono amónicoContenido porcentual nominal del compuesto activo: 90%Potencial de extinción: 40 A : 160 B:CContenido nominal : 100 kgMasa aprox. cargado: 147,5 kgMasa aprox. Descargado: 47,5 kg

Carro Rodante PQS 50 Kg


10/100


11/100

Carro Rodante Espuma 50 LtsESPECIFICACIONES TECNICAS:Naturaleza del Agente : Espuma Mecánica

Nombre químico: AFFF / AR

Contenido porcentual nominal del

compuesto activo: 3%

Potencial de extinción: 20-A : 60-B

Contenido nominal : 50 ltsMasa aprox. cargado: 86,3 kg

Masa aprox. Descargado: 36,3 kg

GABINETE DE RED HUMEDA70X70X30 con carrete de manguera semirígida de 1”

de 25 metros con piton incluido de 3 posiciones :neto $130.000 / iva $24.700 / total $154.700

GABINETE DE RED HUMEDA70X70X30 con carrete de manguera semirígida de 1”

de 30 metros con piton incluido de 3 posiciones :neto $142.000 / iva $26.980 / total $168.980


12/100

Gabinete fabricado con los más altos estándares de seguridad y Calidad, estegabinete reforzado esta diseñado para dar cuidado a su extintor, resistiendo lainclemencia del tiempo y la exposición prolongada. Su diseño lo hace visible y

seguro.

Puerta abatible bisagra pomel con mirilla de inspección y terminación de esmal-te termo convertible de color rojo normalizado. Cierre con llave única.

GABINETE DE EXTINTOR PQSMetálico abatible con puerta de vidrio :

GABINETE DE EXTINTOR PQSMetálico abatible con LLAVE :

Gabinete fabricado con los más altos estándares de seguridad y Calidad, estegabinete reforzado esta diseñado para dar cuidado a su extintor, resistiendo lainclemencia del tiempo y la exposición prolongada. Su diseño lo hace visible yseguro. Gabinete jo de quiebre, incluye martillo de quiebre, soporte y cadena para sufácil manipulación. Todo el gabinete tiene una terminación de esmalte termoconvertible de color rojo normalizado.

GABINETE DE EXTINTOR PQSMetálico DE QUIEBRE :

Gabinete fabricado con los más altos estándares de seguridad y Calidad, estegabinete reforzado esta diseñado para dar cuidado a su extintor, resistiendo lainclemencia del tiempo y la exposición prolongada. Su diseño lo hace visible yseguro. Puerta abatible bisagra pomel con mirilla de inspección y terminación de esmal-te termo convertible de color rojo normalizado.


13/100

GABINETE DE EXTINTOR PQSGabinete de policarbonato (CHICO)

GABINETE DE EXTINTOR CO2Gabinete de policarbonato (GRANDE)

SOPORTE MURAL TIPO LSOPORTE SIMPLE PARA EXTINTORES DE PQS Y CO2:

SOPORTE MURAL pqs 1KGmETÁLICO /PLÁSTICO /pLÁSTICO 2 KG


14/100

Soporte Metálico para extintor PQSTIPO ABRAZADERA DE 4 A 10 KG

Soporte reforzado Económicopara extINTORES Pqs de 4 a 6 kg

Soporte reforzado ROJO TRADICIONALpara extINTORES Pqs de 6 a 10 kg


15/100

Uniones, tuercas. Tapas y traspasos STORZ

VALOR RELATIVO SEGUN LA MEDIDA (CONSULTAR EL REQUERIDO)

UNION Y BIFURCACION DE 3”PARA RED SECA:

PITON NEBLINEROPARA RED HUMEDa


16/100

PITON DE ALUMINIOTRES POSICIONES

CUBRE VOLANTE

negro con insertos efecto fibra de carbono

FUNDAS CUBRE ASIENTOSpolyester - set para 5 plazas

incluye 4 apoya cabezas

SISTEMA LUZ DIAconexión positiva (gris) y conexión negativa (morada)

SISTEMA LUZ DIAAlarma de retroceso 97dB- 12V / 24V / 36V


17/100

BOTIQUIN LONCHEROINCLUYE suministros básicos ante una emergencia

CHALECO REFLECTANTECUMPLE CON TODA LA NORMATIVA

CINTAS REFLECTANTES

COLORES VARIOS


18/100

KIT ANTIDERRAMES MARCA 3MPARA FAENAS MINERAS:neto $66.000 / iva $12.540 / total $ 78.540

PALA ARMABLEarticulada - abierta 24''- cerrada 9,5'':

neto $9.000 / iva $1.710 / total $ 10.710

CUÑAS DE poliuretano ( PU )cuñas para camionetas:neto $36.000 / iva $6.841 / total $ 42.840

cuñas de 20 ton:neto $42.000 / iva $7.980 / total $ 49.980

cuñas de 60 ton:neto $69.000 / iva $13.110 / total $ 82.110

PORTA CUÑAS METALICASC/U:neto $11.500 / iva $2.185 / total $ 13.685


19/100

FOCOS FAENEROS

BALIZAS PARA VEHICULOS MINEROSBALIZA SYFCO AZUL Y AMBAR

CADENAS PARA NIEVESTANDART

EQUIPO MINERO, OPERACION INVIERNOSACO YUTE / frasada de polar


20/100

TENSORES PARA CADENAS

Pértiga Completa de 8 Pies con Led



Banderín Pértiga / Ampolleta Led Pértiga

/ Resorte Pértiga

PÉRTIGAS Y ACCESORIOS


21/100


22/100


23/100

Foam Proportioning & Loose Equipment

ProductWilliams’ “High Head” Through-the-Pump

1500 Portable Foam System

Description:The Williams High Head Through-the-Pump 1500 Portable Foam

System was designed to turn any pumper into a foam producing device. Thisunit will proportion 3% foam solution up to 1500 GPM. It can work againsthydrant pressure up to 50 PSI with only 150 PSI discharge pressure. Thiseconomical system is easy to use and is completely water driven; there are no

pumps or parts to maintain. Can’t get the foam to the pump? Not a problem!The WTTP was designed to proportion foam from remote locations.

FEATURES:• Operates against 33% Pump Suction Pressure. (Example: Master Pressure @150 PSI, Suction Pressure @ 50 PSI)• Proportions Class “B” Foam up to 1500 GPM at 3%.• Proportions Class “B” Foam up to 750 GPM at 6%.• Positive Shut-Off on Metering Valve.• Requires no maintenance.• Portable.• Water Powered.• Remote Proportioning Capabilities.• Check Valve Prevents Water from “Back Flowing“into Concentrate Source.

System Includes:• Base Unit with Jet Pump & Metering Valve.• 2.0” Clear Concentrate Pick-Up Hose.• 2.0” Valved Drum Stinger.

MATERIALS OF CONSTRUCTION:• Brass with Stainless Steel Trim.

Notes:1. The following table is based on 150 psig operating pressure at the jet pump inlet.

2. At 50 psi water pump inlet, maximum hose lay is 25 ft. of 3.0” hose.

3. For drafting operations or pressure below 10 psi, use the 10 psi numbers shown.

ThunderStorm

AFFF/ATC

Maximum Hose Lay (ft) For Remote Proportioning Portable WATP 1500 SystemPUMP INLET PRESSURE

Solution Rate 10 PSIHOSE SIZE

20 PSIHOSE SIZE

30 PSIHOSE SIZE

40 PSIHOSE SIZE

1% 3% 6% 2.5” 3” 2.5” 3” 2.5” 3” 2.5” 3”

30 12 850 1700 625 1250 400 775 200 325

100 40 825 1675 600 1225 375 750 175 300

400 160 80 800 1625 575 1175 350 725 150 275

1000 400 200 750 1500 525 1050 325 650 125 250

2000 750 375 650 1325 475 950 300 600 100 225

4000 1500 750 525 1050 375 775 250 475 75 200


24/100

Foam Proportioning & Loose EquipmentProduct:

Williams’ Pressure Reducing Valve

(WPRV/3, 3P, 4 & 4P)

Description:Maintains constant pre-set inlet pressure for use in conjunc-

tion with the Williams “High Head” Through/Around The Pump(or comparable) foam systems. Allows any firewater pump to pro-duce suction side foam at virtually ANY positive inlet pressure.As such, the WPRV eliminates need for operator intervention to

adjust intake gate valves due to suction pressure fluctuations as aresult of changes in pump discharge flow. Thus, the added burdenof assuring a maximum pump intake pressure (based on pumpdischarge pressure) associated with traditional suction side foamsystems simply goes away.

Additional Applications:Got a CAFS or Balanced Pressure system? The WPRV can provide reduced pump inlet pressures to allow increased

engine/PTO speed to maintain higher compressor or foam pump output when operating with positive pump inlet pressures.Installed within a discharge line, the WPRV maintains a preset pressure for hand lines or ground monitors independent ofhigher pump discharge pressures.

Features:

3 Modes of Operation:1. AUTOMATIC – Controls pre-set pressure from 15-115 PSI2. OPEN – Full flow to rated capacity

WPRV/3 — 500 GPM w/ 7 PSI dropWPRV/4 — 1500 GPM w/ 20 PSI drop

3. CLOSED — Bubble tight shut off• NFPA 1901, 14-6 COMPLIANT — Exclusive WPRV pilot control also provides bubble tight shut off to comply with

NFPA 1901, 19-3.6, TIA 99-1 preventing foam solution back flow into a potable (hydrant system) water supply• PRESSURE RATINGS — 230 PSI Max. — 20 PSI Min. (Prevents reducing hydrant system pressures below 20 PSI)• INLET/OUTLET — WPRV/3: 2.5” NST; WPRV/4: 5” Storz

Options:

WPRV/3 & 3P (Portable)

• “In-Truck” installation with panel mount control valve, standard 2.5” (F)NST swivel inlet w/ strainer and bleeder port• 3” (F) NST inlet w/strainer/outlet• 4” Storz inlet w/strainer/outlet WPRV/4 & 4P (Portable)• “In-Truck” installation with panel mount control valve, standard 5” Storz inlet w/strainer, adjustable intake relief,

bleeder port and mounting hardware• Inlet intake relief valve & bleeder (4P)• 4” Storz inlet w/strainer/outlet• 6” (F)NST swivel outlet for direct mounting to pump intakes• Inlet/outlet pressure gauges• Carrying handle• 5” LDH X 10’ Long with 5” Storz couplings (200 PSI operating pressure)

Materials of Construction:• WPRV/3 & 3P – Epoxy coated cast iron w/brass and stainless steel trim• WPRV/4 & 4P – Epoxy coated & anodized aluminum w/brass and stainless steel trim


25/100


ProductTank Farm Fire Fighting Foam System

Ambassad or JRCP Hose Lay Comparison

Flow

Rate

Solution

%

Jet

Size

# of Jet

lays

2.0” Hose

Lay (ft) Time (min)

2.50” Hose

Lay (ft) Time (min)

3.0” Hose

Lay (ft) Time (min)6,000 1 2 1 N/A N/A 350 1.0 750 2.7

6,000 1 1.5 2 434 1.3 1,250 6.0 2,550 17.2

6,000 3 2 3 N/A N/A 150 0.5 300 1.2

“Old Style” 2 x 6 Gun JRCP Hose Lay Comparison

Flow

Rate

Solution

%

Jet

Size

# of Jet

lays

2.0” Hose

Lay (ft) Time (min)

2.50” Hose

Lay (ft) Time (min)

3.0” Hose

Lay (ft) Time (min)

6,000 1 2 1 N/A N/A 350 1.0 750 2.8

6,000 1 1.5 2 440 1.4 1,300 6.1 2,550 17.4

6,000 3 2 3 N/A N/A 75 0.3 150 0.6


26/100


Product:

Jet Ratio Controllers (Jet Pumps)

Description:Utilizing a small amount of water, this high efficiency ven-

turi-type device moves foam concentrate from a remote storagelocation to a matched Hydro-Foam™ nozzle. This all-hydraulicsystem dramatically simplifies and improves the logistics ofmoving the high quantities of foam concentrate required toextinguish a large flammable liquid fire. Foam concentrate isdelivered from the Jet Ratio Controller to a matched Hydro-Foam™ nozzle via fire hose. Depending on nozzle and hosesize, as well as the percentage of foam mixed (1% or 3%), thedistance between the foam supply and Hydro-Foam™ nozzlecan be up to 2,500 feet.

Jet Ratio Controllers are supplied in conjunction with matched Hydro-Foam™ nozzles. Foam concentrate inlet onmatched nozzle can be provided with 8 ft. of reinforced clear plastic hose with PVC shut-off valve, and/or metering valve“stinger”. This configuration allows foam concentrate to be drawn directly from a foam concentrate drum and then deliveredefficiently to the nozzle via fire hose.

Jet Ratio Controllers are provided with connections at three ports, designated as “inlet,” “discharge” and “suction.” Inlet(female swivel) and discharge (rigid male) has National Hose thread (NST, NH) connections with NPT (M) connection forthe concentrate inlet port. Foam concentrate inlet is furnished with standard drum kit, which consists of flexible suction hose,rigid PVC “Stinger” pipe and shutoff valve. Jet Ratio Controller body is all brass construction. “H” series jet ratio controllers

are available, on special order, for elevated nozzles, or other high back pressure applications.

ThunderStorm ® AFFF/ATC

Typical Schematic


27/100


TYPICAL SCHEMATIC

NOTE: 6% APPLICATIONS AVAILABLE UPON REQUEST

ThunderStorm ®

AFFF/ATC

1.5”INLET

MODEL 3% Flow Match 1% DISCHARGE “A” SUCTION “B” LENGTH “C”

1.5JP24 750 GPM 2000 gpm 1.5” 1.5” 12.375”1.5JP30 1000 GPM 2500 gpm 1.5” 1.5” 12.375”

2.0JP60 2000 GPM 5000 gpm 2.5” 2” 15.5”


28/100


Product:

95 gpm Liquid Eductor

Description:

The Elkhart 242-95 Eductor is a device used for educt-ing a liquid concentrate solution into the water stream of1-1/2” coupled fire hose lines.

The Eductor is constructed of Armor-Lyte ™ compositematerial with stainless steel components for resilience anddurability. Armor-Lyte ™ is impervious to the corrosioncaused by high concentrate detergents, salt water and mostchemicals.

Each eductor comes equipped with a 1-1/2” “F” NH

female swivel connector input, a 1-1/2” “M” NH male outletand a 3/4” male Garden Hose Thread inlet for the concen-trate pick-up hose.

The 242-95 Eductor is factory calibrated for pump flow rates of 95gpm (356 lt/m). The Eductor comes complete withthree different checkvalves for three different concentrate eduction rates. When attached, the Black checkvalve will educt ata 0.5% rate, the Purple checkvalve will educt at a 1% rate and the Green checkvalve is for educting at a 3% rate.

.wercsnudnaspirgesivrosreilphtiwydobevlavk cehcehtpsargyltneg,tinurotcudeehtnosevlavk cehchctiwso TCarefully screw alternate checkvalve into eductor body, thread to “hand-tight”. There is no need to over tighten.

The 242-95 Eductor can be used as either an “End-of-the-Line” or as a “Pump Mounted” System. The eductor is designedfor a nominal operating pressure of between 75 and 150 psi. If proportioning 3%, the 242-95s are restricted to a maximum

1.50”ID fire hose goes to 200 feet when used with a 95+gpm nozzle.

The Eductor comes complete with

three different checkvalves for three

different concentrate eduction rates.

*Armor-Lyte™ is a registered trademark of

Williams Fire and Hazard Control, Inc ®


29/100


Product:Spectrum Inline Eductors

Description:Spectrum Inline Foam Eductors provide the simplest and

most economical method of introducing a controlled flow offoam concentrate into a pressurized water stream. As opposed to“Hydro-Foam™ Technology”, (which is used in conjunction withmaster stream nozzles) these “Venturi-Type” foam proportionersare designed to be used in conjunction with a matched constantflow end-of-line device (nozzle), where adequate water pressureis available. Inline foam eductors are capable of operating at inlet

pressures as low as 70 psi, but in most cases adequate residual fire

fighting pressure at the nozzle requires that the eductor inlet pres-sure be at least 100 psi, or greater.

Spectrum Inline Eductors are rated to flow 60, 95, or 125 gpm @ 150 psi inlet. Nominal flow rates at other inlet pres-sures are listed below. Eductor outlet pressure is approximately 65% of inlet pressure. Eductor components, including body,venturi jet and metering orifice are constructed of corrosion-resistant brass.

Standard water inlet - NH (F) swivel. Foam solution discharge - NH (M). Complete with clear pvc concentrate pick-uphose with slotted brass “stinger”; 1% or 3% fixed orifice; ball check valve.

RIGID

Model Nominal Flow@100 PSI

Nominal Flow@125 PSI

Nominal@150 PSI

Proportioning

1.5” -60 gpm 49 gpm 55 gpm 60 gpm 1% or 3%

1.5” -95 gpm 78 gpm 87 gpm 95 gpm 1% or 3%

1.5” -125 gpm 102 gpm 114 gpm 125 gpm 1% or 3%


30/100


Product:Spectrum “Double Action” By-Pass Eductor

Description:The Spectrum “Double Action” By-Pass Foam Eductor pro-

vides the versatility of a full-flow water by-pass foam proportionerin conjunction with the simplicity and reduced weight of a stan-dard, single waterway inline eductor. This specialty by-pass typefoam venturi transforms any 1.5” handline into a foam proportion-ing system. Three flow rates are available: 60 gpm; 95 gpm; 125gpm. Flows are based on 200 psi inlet pressure. The eductor will

proportion foam at lower inlet pressures, provided that discharge pressure is not excessive. Positive shut-off metering allows foam

proportioning to be adjusted and set from 0.5% to 3%. Body isconstructed of durable 6061 - T6 (black) anodized aluminum.

In operation, foam is produced by simply installing the system in the hose line, emersing the concentrate pickup tubeinto an adequate supply of ThunderStorm® AFFF foam concentrate and adjusting the eductor to the “foam” position. Whenfoam application is no longer needed, there is no need to remove the eductor for application of water only. This conversionis easily accomplished by simply rotating the foam control sleeve to the “water” setting. The result is an enlarged waterwaywhich allows for water only application.

Other Features Include:• Positive Shutoff Metering Valve.• Integral Concentrate Ball Check Valve.• Clear Plastic Concentrate Pick Up Hose with Rigid “Stinger”.

• Lightweight, Compact Design (4 lbs., nominal).

Double ActionEductor

Nominal Flow@200 PSi

K-Factor Inlet Discharge ProportioningRange

60 gpm 60 gpm 4.25 1.5 NH (F) Swivel 1.5” NH (M) 0.5%-6%




31/100


32/100

Hydro-Chem™ Technology

Manifolds for Hydro-Chem™ Systems

Dry Chemical Manifiold - 4 Inlets

Dry Chemical Manifiold - 6 Inlets


33/100


Typical Hose Lay For Hydro-Chem™ Trailer mount Systems

1000 GPM Hose Layout

Patriot II Hose Layout


34/100

Monitors

Product:

Daspit Tool™

Features:Patented “Daspit Tool” tank frame clamp with 5” vertical waterway“Daspit Tool” Specialty Flange Monitor Adapter “Daspit Tool” Rotator Elbow with Storz inlet and 4.5” (F) NH swivel adapter

Component Weights:Daspit Tool™ Tank Clamp = 89 lbs

Accessory Component Weights:90˚ Aluminum Rotator Elbow - 4.5” (F) NH Swivel x 5” Storz = 22 lbs 30˚ Aluminum Rotator Elbow - 4.5” (F) NHSwivel Elbow x 5” Storz = 9 lbs

4” Aluminum Tiller Bar Monitor w/ 4.5” (F) NH Swivel inlet = 43 lbs4” Aluminum Dual Hand Wheel Monitor - 4.5” (F) NH Swivel inlet = 50 lbsRanger™ 1.5 Nozzle = 22 lbs

Applications:Sunken roof Rim Seal fireVapor Suppression/Mitigation

Options:

3” Aluminum Waterway Monitor w/Tiller Bar Control250-1,000 gpm Automatic Nozzle4” Aluminum Waterway Monitor w/Dual Hand Wheel Control500-2,000 gpm Automatic NozzleRim Mounted ModelTruck Mounted Model“Throw-Down” ModelTank Mount Standard Unit

For US and Foreign Patent and Trademark information, please refer to page IP2


35/100

Monitors

Product:Daspit Tool - Truck Mount™



36/100

Monitors

Product:

Daspit Tool™ - Throw Down Model

Component Weights:Daspit™ Tool Throw Down Mount = 113 lbs8 Stabilizing stakes = 64 lbs


47.875”


37/100

Monitors

Product:

Alpha MA-HV4 Monitor

Description:Rugged lightweight aluminum construction 4” ID full flow monitor with “Quick Acting” Tiller-Bar control for vertical

and horizontal movement. Red powder coat anodized aluminum. The single 4” full-flow waterway with internal turning vanesis designed to provide maximum efficiency. The “Easy-Lock” brake system insures that the nozzle position “stays put” withthe simple twist of an ergonomically designed locking bar. Monitor features a 3.50” (M) NH outlet and a 4.0” 150# ASAflat-faced flange inlet. Horizontal articulation is 360˚ and vertical travel is 75˚ up and -25˚ down.


38/100

Monitors

Product:

Alpha-E Tiller Bar Montior - 3”

Description:Rugged, corrosion resistant brass construction; unique configuration flows up to 1250 gpm; compact - just 16” high; 3”

NPT female, 3” or 4” 150# ANSI flange; vertical movement 90 degrees above horizontal to 45 degrees below; full, continuous360 degree rotation; rugged, stainless steel lock hardware; brass balls in all swivel joints; grease fittings for easy lubricaion;durable acrylic urethane finish

Alpha-E Till er BarMonitor

Waterway Inlet Discharge Material Vertical TravelHorizontal

Rotation

3” 3”-4” Flanged 2.5” NH(M) Cast Brass 90º 360º


39/100

Monitors

Product:“SharpShooter Four” Tiller Bar -4”

Description:Superior grade 4” I.D. waterway monitor with tiller bar

control for vertical and horizontal movement. Designed foruse in corrosive atmospheres that require the dependabilityand durability of an all brass monitor. Single waterwaywith turning vanes providing excellent projection for wateror foam streams. Flows up to 1,500 gpm.

Tiller bar control with brake band swivels, adjusts, then

locks at the vertical and horizontal position. Vertical settingis from minus (-) 10º to plus (+)70º. Full 360 degree hori-zontal travel. Painted red polyurethane finish. 3.5”NH (M)discharge threads. Base -4” 150 # ASA flange.

SharpshooterFour

Waterway Inlet Discharge Material Vertical Travel

Horizontal

Rotation

4” 4” Flange 3.5” NH(M) Cast Brass 80º 360º


40/100

Monitors

Product:

“SharpShooter Four” Dual Handwheel -4”

Description:Superior grade 4” I.D. waterway monitor with dual handwheel/worm

gear operation for vertical and horizontal movement. The ultimate monitorfor portable applications or for fixed installations where precise and posi-tive control are needed. Designed for use in corrosive atmospheres thatrequire the dependability and durability of an all brass monitor. Singlewaterway with turning vanes providing excellent projection for water orfoam streams. Flows up to 1,500 gpm.

.º09)+(sulpotº01)-(sunimmorf yrotce jartstsu jdaleehwdnahlacitreVHorizontal handwheel allows for full 360º rotation. Painted red polyure-thane. 3.5”NH (M) discharge threads. Base -4” 150 # ASA flange.

SharpshooterFour

Waterway Inlet Discharge Material Vertical Travel HorizontalRotation

4” 4” Flange3.5” NH(M)

FlangeCast Brass 100º 360º


41/100

Monitors

Product: Alpha-SHW Single HandWheel Monitor - 3”

Description:Rugged, cast brass construction • Full 3.0” unobstructed waterway • FLows up to 1250 GPM • Handwheel driven worm

gear fully enclosed and protected from the elements • Stainless steel worm • Vertical travel from 70˚ above to 70˚ belowhorizontal • Gear holds vertical position wherever it is stopped • Four ball races with bronze balls and grease zerks for easylubrication • Full 360˚ rotation with positive twist lock • 2.5” male outlet • FM Approved • See chart for base options • Finishred urethene enamel.

Model Waterway Inlet Discharge Material Vertical TravelHorizontal

Rotation

Alpha-SHW 3” 3” or 4” Flange 2.5” NH(M) Cast Brass 90º 360º


42/100

Monitors

Product:Spectrum “Mini- Monitor” -2”

Description:Designed for use in corrosive atmospheres that require the

dependability of an all brass monitor. Suitable for most industrialenvironments. Flows up to 300 gpm @ 100 psi. Full 2” I.D. water-way, efficiently designed to minimize pressure drop. 2” NPT femaleinlet base, 1.5” NH male discharge tip. Tiller bar control handle withrubber grip. Vertical (110º) and horizontal (360º) adjustments with

positive quarter-turn locking handles. Natural brass finish.

Model Waterway Inlet Discharge Material Vertical Travel HorizontalRotation

Mini Monitor 2” 2”NPT (F) 1.5” NH(M) Cast Brass 110º 360º


43/100

Oscillating Monitors

Product:Spectrum High Flow Model 4 Oscillating Monitor Tiller Bar Control

Description:For flows between 750 - 1500 gpm. Spectrum High Flow Model

4 water-powered oscillating monitor is constructed of predominantlycorrosion-resistant materials. Cast brass monitor body with stain-less steel trim. 4” I.D. waterway with turning vanes. Controls pro-vided for adjusting vertical trajectory as well as horizontal position.Reciprocating motion is generated by a two-way high performancehydraulic actuator. Oscillation is accomplished through the use of

plated sprockets and a heavy duty drive chain. Standard arc of oscil-lation is from 0-90˚ and speed of oscillation is from 0-40˚ per second.

Vertical trajectory is from minus (-)10˚ to plus (+)70˚. Standard inletflange - 4” 150# ASA RF Flange. Monitor is to be used with eithera non air-aspirating or air-aspirating nozzle. Standard 3.5” NH (M)discharge. Oscillating mechanism is Factory Mutual Approved - File

No. J.I.1R6A3.AF.

* Minimum operating pressure = 50 psi

(Nozzle shown for

reference only)

Model Flow @ 100 PSI Inlet Discharge Water I.D.

High Flow Model 4Tiller Bar Control

Between 750-1400 gpm 4” 150# ASA RF flange 3.5” NH (M) 4”


44/100


Product:

Spectrum Medium Flow Model 4Oscillating Monitor

Description:For flows between 150-750 gpm. Spectrum Medium Flow

Model 4 low profile water-powered oscillating monitor features asuper-compact design, as well as predominantly corrosion resistantmaterials of construction. Reciprocating motion is generated by atwo way high performance hydraulic actuator. Oscillation is accom-

plished through the use of plated sprockets and a heavy duty drivechain. Arc of oscillation is from 0-185º and speed of oscillation isfrom 0-40º per second. Nozzle elevation is from 10º below to 70º

above horizontal. Single brass 3” I.D. waterway with turning vanes provided with positive horizontal and vertical locks. Standard inletflange - 4” 150# ASA RF Flange. Monitor can be used with either anon air-aspirating or air aspirating nozzle. Oscillating mechanism isFactory Mutual Approved - File No. J.I.1R6A3.AF.


(Nozzle shown forreference only)


Medium Flow Model 4 Between 150-750 gpm 4” 150# ASA RF flange 2.5” NH (M) 3”


45/100


Product:

Spectrum Marine Grade Model 4Oscillating Monitor

Description:For flows between 150-750 gpm. Spectrum Marine Grade Model 4 low profile water-powered oscillating monitor fea-

tures a super-compact design, as well as construction of totally corrosion resistant materials to include inlet flange, enclosureand drive mechanism, sprocket and chain — all manufactured in 316 Stainless Steel. Reciprocating motion is generated by atwo way high performance hydraulic actuator. Oscillation is accomplished through the use of plated sprockets and a heavyduty drive chain. Arc of oscillation is from 0-185º and speed of oscillation is from 0-40º per second. Nozzle elevation is from10º below to 70º above horizontal. Single brass 3” I.D. waterway with turning vanes provided with positive horizontal andvertical locks. Standard inlet flange - 4” 150# ASA RF Flange. Monitor can be used with either a non air-aspirating or airaspirating nozzle. Oscillating mechanism is Factory Mutual Approved - File No. J.I.1R6A3.AF.



Marine GradeModel 4

Between 150-750 gpm 4” 150# ASA RF flange 2.5” NH (M) 3”


46/100


Product:Spectrum Low Flow Model 4 Oscillating Monitor

Description:For flows between 100-350 gpm. Spectrum Low Flow Model 4 low

profile water-powered oscillating monitor features a super-compact design,as well as corrosion resistant materials of construction. Reciprocating

.r otautcaciluar dyhecnamr of r e phgihyaw-owtay bdetar enegsinoitomOscillation is accomplished through the use of plated sprockets and a heavyduty drive chain. Arc of oscillation is from 0-185º and speed of oscillationis from 0-40º per second. Nozzle elevation is from 30º below to 80º abovehorizontal. Single brass 2” I.D. waterway. Provided with positive horizontal

and vertical locks. Standard inlet flange -4” 150#. Monitor can be used witheither a non air-aspirating or air-aspirating nozzle. Oscillating mechanism isFactory Mutual Approved - File No. J.I.1R6A3.AF.


(Nozzle shown for

reference only)


Low Flow Model 4 Between 100 - 350 gpm 4” 150# ASA RF flange 1.5” NH(M) 2”


47/100


Product:“Durham” Oscillating Monitor Conversion Kit

Description:The Durham Conversion Kit transforms an existing manual sta-

tion monitor into an oscillator. Designed for use with most 2.5” or 3”I.D. single waterway monitors, flowing up to 750 gpm. Upgradingfoam or water monitor coverage in any area is now as easy as unbolt-ing the existing monitor and inserting the conversion kit betweenthe flanges. Oscillating mechanism is identical to the one used onthe Spectrum Model 4 Oscillating Monitor and is Factory MutualApproved - File No. J.I.1R6A3.AF. Standard inlet and discharge

flange is -4” ASA RF Flange 150#. Optional inlet and dischargeflanges available upon request.


DurhamConversion Kit

up to 750 gpm 4” 150# ASA RF flange 4” 150# ASA RF flange 2.5” or 3”


48/100

Remote Control Monitors

Product:

Spectrum Direct-Mounted Electric Actuated Monitor

Description:Flows water or foam from 500 to 6,000 gpm. The Spectrum Direct-Mounted

Electric Actuated High Volume/Remote Control Monitor has a programmableoscillation capability, but may also be overridden with a matched Hydro-Foam™nozzle operated remotely through the use of a joystick and switches on a consoli-dated control panel. Manual operation can also be accomplished locally throughthe use of handwheels. Foam concentrate can be proportioned at the nozzlethrough the use of a jet ratio controller and atmospheric concentrate storage tank.All electric actuators are reversible, NEMA 7 explosion proof, refinery grade,F.M. Approved and C.S.A. certified. No external controls, starters, or starters in

.der iuqer er asr otcudnoclor tnocdnar ewo pylnO.dedeener ar etneclor tnocr otomMonitor can be programmed to “return to home” position (horizontal, vertical,nozzle to wide angle fog) after use, automatically, whether P.L.C. controlled orhard wired.

Two direct mounted electric actuators with speed reducing gear drives installed on the motor enable remote control ofhorizontal position, as well as vertical trajectory. Field-adjustable limit switches on each actuator allow 340º horizontal rotation and from minus (-)70º to plus (+)70º vertical travel. Monitor traversing speed is a least 10º per second. A third direct-mounted electric actuator enables remote operation for the nozzle’s discharge pattern, from wide fog to straight stream.

Weather protective cowlings are provided over all gears and shafts. Monitor and controls are designed for minus(-)20º F operation. Maximum working pressure is 200 psi.

Stainless Steel monitor (waterway) with red epoxy finish. Includes lifting lug for handling and mounting. Stainless steel

06/3/084siegatlovr otomdr adnatS.tf ahsssar bdetal plek ci N.sr aegeznor b/leetS.sgnir ae blla bleetssselniatshtiwsleviwsStandard Control voltages is 120 Vac. Other voltages are available when required.

Model Nominal flow range Inlet Pressure Drop

4” Waterway Monitor 500-1500 gpm 4” flange @ 1500 gpm-9 psi




49/100


Spectrum Direct-Mounted

Electric Actuated Monitor


50/100


Product:

Spectrum Electro/Hydraulic Actuated Monitors

Description:Flows water or foam from 500 to 3,000 gpm. The Spectrum Electro/

Hydraulic High Volume/Remote Control Monitor is operated remotely throughthe use of a joystick and switches on a consolidated control panel. Manual opera-tion can also be accomplished locally through the use of handwheels.

Two hydraulic actuators installed on the monitor enable remote control ofhorizontal position, as well as vertical trajectory. Maximum travel is limited to340 degrees horizontal travel and from minus (-)70 degree to plus (+)70 degree

vertical travel. Monitor traversing speed is at least 8 degrees per second. Adirect-mounted linear hydraulic actuator enables remote operation for thenozzle’s discharge pattern, from wide fog to straight stream. Weather protectivecowlings are provided over all gears and shafts.

.elzzonmaer tsthgiar ts-ot-gof gnitar i psar ianondr adnatsahtiwde p piuqEWith a matched Hydro-Foam™ nozzle, foam concentrate can be proportioned atthe nozzle through the use of a jet ratio controller and atmospheric concentratestorage tank.

Stainless steel monitor (waterway) with red epoxy finish. Includes liftinglug for handling and mounting. Stainless steel swivels with stainless steel ball

bearings. Steel/bronze gears. Nickel plated brass shaft. Anodized aluminum

fog/straight stream nozzle.

ModelNominal flow range

@ 100 psiInlet Pressure Drop




51/100


Spectrum Electro/Hydraulic

Actuated Monitor


52/100

Monitor Accessories

Product:

Hydrant Monitor Stand

Description:For mounting monitor station (Hydro-Foam™ or water only)

onto any fire hydrant. Standard configuration: water inlet is 2.5” NH(F) brass swivel; 3” waterway with 90 degree elbow; bolted ver-tical support stanchions; flanged discharge (specify either 3” or 4”150# ASA). Red polyurethane finish.

Monitor Stand shown with Hydrant and Optional

Monitor and Nozzle.

Note: hydrant not included.


53/100

Ranger3™ Nozzle

Product:Ranger3™ Monitor/Nozzle

The Ranger3™, featuring “Smart Nozzle” Technology, was designed for today’sIndustrial fire fighting and protection needs. Hazards involving flammable liquids instorage and liquids under pressure have met their match with the New MillenniumEquipment from Williams Fire & Hazard Control, Inc®.

The Ranger3™ nozzle combination is capable of not only self-educting foamconcentrate, but can do so while maintaining a nearly constant pressure (+/-10%)and a constant foam percentage (1% or 3% selectable) regardless of the flow rate.Discharge flow rates from 1000-3000 USGPM (3800-11356 LPM) can be water only,Hydro-Foam™ (using jet pumps or automatic constant/selectable metering) or Hydro-

Chem™ for extinguishing liquids and gases under pressure.

Advancing the Fire Fighter’s Abilit y with Equipment and

Knowledge.

This “Hybrid” nozzle has the unique capability to perform as an automatic pressure or fixed gallonage nozzle. Duringautomatic operation the nozzle will respond to varying flows to maintain a nearly constant tip pressure, thus maximizing effec-tive range for a given discharge flow. Once the nozzle reaches the fixed gallonage set point (1000-3000 GPM), it performsas a conventional fixed gallonage nozzle. This is desirable for foam proportioning operations on storage tank fires or otherhazards requiring specific application rates. This nozzle is capable of Hydro-Foam™ proportioning at rates up to 3000 GPM@ 3%. It can automatically maintain a nearly constant foam percentage (1% or 3%) throughout the entire flow range whileself-educting. It can optionally be configured to proportion foam from remote locations using jet pump technology (thus for-feiting the constant/selectable metering feature). The extensive Ranger3™ options list allows this nozzle to be Hydro-Chem™

capable (without Hydro-Foam™ capability) with PKW™ flow rates from 25 lbs/s to 50 lbs/s. Pattern control from straightstream to full fog is accomplished via a full wrap-around handle attached to the outer sleeve.

*See Williams’ Nozzle Range Chart on page D5


Standard Features List:Dual Mode Automatic/Fixed Operation

Fixed Gallonage plugs: 1K, 2K, 3K

Hydro-Foam™ Constant/Selectable

1% or 3% Nozzle

Wrap-around handle design for pattern control

Options:Hydro-Chem™ Tip conversion

Choke tubes (25 and 50 lbs/s)

Dry chemical manifolds (4 inlet or 7 inlet)

1.5JP30 Jet Pump w/stinger (one)

2.0JP60 Jet Pump w/stinger (one)

2.5” x 10 Dry Chemical Hose

3-2.5” FNST x 3.0” MNPSH Siamese(Jet to Monitor Supply)

1-2.5” FNST x 3-1.5” MNST Wye

(Jet Pump Supply)


54/100

Hydro-Foam™ Nozzles

Product:

Ranger Lightning

Description:Ranger Lightning is the latest in a series of innovative lightweight Hydro-Foam™, self-contained foam systems as defined byNFPA standard 1901, Section A-8-3.22.

This rugged design is the first in a series of master stream nozzles to feature Williams Fire & Hazard Control’s Armor-Lyte™construction.

Armor-Lyte™ is a composite of lightweight, non-corrosive materials that provide years of trouble-free service.

Features

• Self-educts foam concentrate directly from an atmospheric source.• Selectable gallonage with matched foam proportioning of 1% and 3% at 350, 500, or 750 gpm at 100 psi operating

pressure.• Flush setting as recommended per NFPA 1964.• Change ow rate, proportion rate, or ush without the need to

shutdown.• Positive lock feature for rate selection!• Self-contained internal stream straightner to maximize range!• T-handle for pattern control for full fog to straight stream.• Complete unit weighs only 6 lbs!• 1.00” MNPT foam inlet port.• 2.50” FNST Swivel inlet connection.

Options• Available in Hydro-Chem and Master Stream (water only) versions.• Actuated pattern control in 12vdc, 24vdc, pneumatic, or hydraulic.• Nickel-plated brass swivel inlet.• Nozzles available at: .5% & 1% proportioning selections

Special inlet threads available upon request.

Selectable gallonage with matched foam

proportioning of 1% and 3%Inlet view


55/100


Product:HF Ranger™ “Select” - Automatic/Constant Metering

Foam Nozzle

Description:Introducing the most advanced foam fire fighting nozzle ever made! The

Hydro-Foam™ Ranger™ “Select” Nozzle combines the effective range ofan automatic nozzle, while incorporating the exclusive combination of selfeducting/selectable “constant metering” foam proportioning. It is capable ofaccurate foam proportioning (Selectable 1% or 3%) over a broad range offlows (250 - 1500 gpm), while maintaining automatic control of tip pressure(100 psi +/- 10%) over the entire flow range. This constant nozzle pressurecapability maximizes the effective discharge reach for any given flow. The

discharge pattern is adjustable from full fog to straight stream. Constructed ofanodized aluminum with “wrap around” control handle and protective rubber

bumper. Water inlet is available in nickel plated brass as an option. Manuallyoperated nozzle is available with automatic controls: 12v; 24v; or hydraulic.

Options:• 2.5” or 3.5” swivel• Nickel plated brass swivel• 12v, 24v or hydraulic pattern activation

*Refer to page D14 for complete part# and ordering information


ModelRanger™ Hydro-Foam™

Ranger™ HFR 1.0 M 2.5* Rang er™ HFR 1.5 M 3.5*

Water Inlet * 2.5” (F) NH Swivel 3.5” (F) NH Swivel

Foam Concentrate Inlet *

1.50 M/NPT

w/1.5” x 8 Flexible Pickup

Hose & 1.5” Rigid PVC

Drum “Stinger”

2.00 (M) NPT

w/2” x 8 Flexible Pickup

Hose & 1.5” Rigid PVC

Drum “Stinger”

Foam/Water Flow(@ 100 psi)

250-1000 gpm 250-1500 gpm

Proportioning(Selectable)

1% or 3% 1% or 3%

Appli cati on Class “B” Liquid Fires


56/100


Product:

Constant Flow Ranger™ 750, 1000, 1250 & 1500 GPM

Description:Water powered nozzle system that proportions and delivers either water

or foam to the hazard area. Fully adjustable from straight stream to full fog.Constructed of hard anodized aluminum alloy with stainless steel trim. Water inletis available in nickel plated brass as an option. Nozzle is supplied with flexible 8ft. pick-up hose with 1.5” rigid pvc drum “stinger”. Built in select feature provides

proportioning at either 1% or 3%. Fixed foam proportioning may be proportioneddirectly from atmospheric source. Manually operated nozzle is also available withautomatic controls: 12v; 24v; or hydraulic. Optional “Jet Pump” is available forremote proportioning.


Fixed Ranger™750

Fixed Ranger™1000

Fixed Ranger™1250

Fixed Ranger™1500

Nominal Flow@100psi

750 gpm 1000 gpm 1250 gpm 1500 gpm

K-Factor 75 100 125 150

Nominal Range@ 100psi(straight stream)

215 ft. 250 ft. 260 ft. 275 ft.

Water inlet standard 2.5”NH (F) 2.5”NH (F) 3.5”NH (F) 3.5”NH (F)

Concentrate Inlet 1.5” NPT(M) 1.5” NPT(M) 2” NPT(M) 2” NPT(M)

Proportioning without jet

1% / 3% 1% / 3% 1% / 3% 1% / 3%


57/100

Monitor Foam Nozzles, Air Aspirating

Product:Hydro-Air Foam Monitor Nozzles, Medium (Not shown)

& Big Body

Description:Exclusive super-compact, air aspirating foam nozzle with adjustable stream

from full fog to straight stream! Has the appearance of a standard fog/straightstream monitor nozzle, yet the “Hydro-Air” venturi provides foam expansion ratiosof up to 6:1 by actually inducting air into the center of the master stream. MediumBody Nozzles are available in lightweight anodized aluminum. Standard flowrates from 350 to 1500 gpm at 100 psi. As an option, nozzles can be factory modi-fied to flow from 200 to 1500 gpm at specific inlet pressures.


For US and Foreign Patent and Trademark information, please refer to page IP

Air Inlet

Foam Inlet(F) NH Swivel

Big Body “Ranger™”

Hydro-Air Nozzle

750-1500 GPM

Medium BodyHA-350

Medium BodyHA-500

Medium BodyHA-700

Big BodyHA-1000*

Big BodyHA-1250

Big BodyHA-1500*

Flow @100 psi 350 500 700 1,000 1,250 1,500

Standard inlet 2.5”NH(F) 2.5”NH(F) 2.5”NH(F) 2.5” or 3.5” 2.5” or 3.5” 2.5” or 3.5”

Material Brass Brass Brass Aluminum Aluminum Aluminum


58/100

Monitor Nozzles

Product:

Ranger™ Automatic - Master Stream Nozzle

Description:The Ranger™ Automatic Master Stream Nozzle is made for use

on monitors, ladder pipes, deluge guns and aerial platforms. This noz-zle’s uniquely-designed constant-pressure feature assures maximumeffective reach for either water or foam/water solution. The tip pres-sure is automatically controlled to maintain a constant pressure (100 psi+/- 10%) over the nozzle flow range, which is from 250 gpm to 1,500gpm. (Other maximum flow stops available). The nozzle pattern isadjustable from full fog to straight stream. Constructed of anodizedaluminum with exclusive “wrap-around” control handle and protec-

tive bumper. Water/foam solution inlet is available in nickel plated brassas an option. Nozzle is used in conjunction with an independent foam

proportioning system when applicable. Manually operated nozzle is also avail-able with automatic controls: 12v; 24v; or hydraulic.


Model Nozzle PatternControl

Solution Inlet* Solution Rate(GPM)

Material ofConstruction

MSR1.O M 2.5 Manual 2.5” 250-1,000 Anodized Alum.

MSR1.5 M 3.5 Manual 3.5” 250-1,500 Anodized Alum.

MSR1.O A 2.5 12 vdc electric 2.5” 250-1,000 Anodized Alum.

MSR1.5 A 3.5 12 vdc electric 3.5” 250-1,500 Anodized Alum.

MSR1.O B 2.5 24 vdc electric 2.5” 250-1,000 Anodized Alum.

MSR1.5 B 3.5 24 vdc electric 3.5” 250-1,500 Anodized Alum.

MSR1.O H 2.5 Hydraulic 2.5” 250-1,000 Anodized Alum.MSR1.5 H 3.5 Hydraulic 3.5” 250-1,500 Anodized Alum.


59/100


The most effective method for extinguishing large pressure and flowing fuel fires.*

By using foam solution as the means to propel, Hydro-Chem™ Systems project dry chemical approximately three to fourtimes farther than that of conventional dry chemical equipment. Hydro-Chem™ technology gives the firefighter a safer andmore efficient integrated system of delivering dry chemical onto large pressure and flowing fuel fires.

In operation, ground fires are extinguished using foam only. The foam solution applied then “ties-up” or harnesses thethree dimensional fire, greatly reducing flame intensity. After this reduction in heat, dry chemical is then injected into thefoam stream, resulting in a more proficient extinguishment of the fire. Each system is used in conjunction with customer-

provided dry chemical storage equipment.

*Not normally intended for use on liquefied petroleum gas fires.

For US and Foreign Patent and Trademark information, please refIP2


60/100

Hydro-Chem™ Nozzle

Product:HC Ranger™-Automatic Hydro-Chem™ Nozzle

Description:The Hydro-Chem™ Ranger™ Nozzle combines the effective range

of an automatic nozzle, while incorporating the dry chemical/foam solu-tion delivery capabilities of Hydro-Chem™ Technology. Designed toextinguish three dimensional and oxygenated fuel fires. This uniquenozzle projects dry chemical (@ 20 lbs./sec.) through the center of thefoam/water stream, resulting in an effective range not possible with con-ventional dry chemical equipment. The constant pressure feature assuresmaximum effective reach of the foam/water solution. The tip pressureis automatically controlled to maintain a constant pressure (100 psi

+/- 10%) over the nozzle flow range, which is from 250 gpm to 1,500.maer tsthgiar tsotgof lluf mor f el batsu jdasinr etta pegr ahcsidehT.m pg

Constructed of anodized aluminum, with “wrap-around” control handle and protective rubber bumper. Foam solution/water inlet is available in nickel plated brass as an option. Nozzle is used in conjunction with an indepen-dent foam proportioning and dry chemical delivery system.



Basic Model# * Nozzle PatternControl

Water Solution Inlet* Solution Rate (GPM) Material ofConstruction

HCR1.O M 2.5 Manual 2.5” 250-1,000 Anodized Alum.

HCR1.5 M 3.5 Manual 3.5” 250-1,500 Anodized Alum.

HCR1.O A 2.5 12 vdc electric 2.5” 250-1,000 Anodized Alum.

HCR1.5 A 3.5 12 vdc electric 3.5” 250-1,500 Anodized Alum.

HCR1.O B 2.5 24 vdc electric 2.5” 250-1,000 Anodized Alum.

HCR1.5 B 3.5 24 vdc electric 3.5” 250-1,500 Anodized Alum.

HCR1.O H 2.5 Hydraulic 2.5” 250-1,000 Anodized Alum.

HCR1.5 H 3.5 Hydraulic 3.5” 250-1,500 Anodized Alum.


61/100

Hydro-Chem™ Nozzles

Product:Handgun Hydro-Chem™ Variable Flow Nozzle

Description:Dual-agent pistol grip handline nozzle incorporates a foam solu-

tion or water application with simultaneous Hydro-Chem™ Technologywhich projects dry chemical through the center of the foam/water streamto achieve ranges not possible with conventional equipment. Used in con-

junction with a separate foam proportioning system.The foam/water stream is adjustable from full fog to straight stream.

Collar mounted ring adjustment allows quick selection of 60, 95 or 125gpm flow rates — also features a flush setting. The nozzle features sepa-rate flow valves for water/foam and dry chemical operations. Constructed

of hard anodized aluminum alloy. Total nozzle weight 7 lbs.

Options Include:Three inlet valved dry chemical inlet manifold (not shown); flat lay

dry chemical inlet hose, 1.5” x 50’, coupled 1.5 (M) NH; “cross-over”adapter (for Ansul 350 lb wheeled unit) 1.25” (F) NPSH X 1.5” (M) NH

NOTE: 1.0” NH (F) Swivel connections also available for

water/foam and dry chemical

* Varies depending on dry chemical delivery system andlength of hose lay

For US and Foreign Patent and Trademark information,please refer to page IP2

Part # HCHG-S

Water/Foam Flow 60, 95, 125 gpm

Dry Chemical Flow* 5, 7.5, 10 lbs / sec

Water/Foam Solution

Inlet NH (F)

1.5” Swivel NH (F)

Dry Chemical Inlet 1.5” Swivel NH (F)


62/100

R - - - -

VERSION: HF - Hydro-Foam™ HC - Hydro-Chem™ (1.5” (F)NPT CHEMICAL INLET STD.) MS - MASTER STREAM

FLOW RANGE: 1.0 250-1000 USGPM - Automatic 1.5 250-1500 USGPM - Automatic X Special - Fixed Flow or Automatic

(Requires Engineering Approval - Specify As Option)

PROPORTIONING METHOD: N None (Required for HC & MS Versions) F Fixed Rate (HF Only) S Selectable Rate (HF Only) J Jet Pump (HF Only - Requires Engineering Approval -

Limited to 750 GPM for 3% Proportioning)

PROPORTIONING RATE: 0 None (Required for HC & MS Versions) .5 .5% (Fixed Only) (1” MNPT Foam Inlet Std) 1 1% (Fixed), .5% (Selectable) (1.5” MNPT Foam Inlet Std) 3 3% (Fixed), 1-3% (Selectable) (2” MNPT Foam Inlet Std)

X Special (Requires Engineering Approval)

PATTERN CONTROL: M Manual A 12VDC Actuated B 24VDC Actuated H Hydraulic X Special

INLET CONNECTIONS: 2.5 2.5” FNST (Standard on 1.0 Flow Range) 3.5 3.5” FNST (Standard on 1.5 Flow Range) 64 64MM (2.5”) FBSP 89 89MM (3.5”) FBSP X Special (Requires Engineering Approval)

OPTIONS: 0 None 1 90˚ Swivel w/1.5” FNPT Foam/Chemical Inlet Port (Not recommended for HF1.5) 2 90˚ Swivel w/1.5” FNST Swivel Foam/Chemical Inlet Port (Not recommended for HF1.5) 3 Nickel Plated Brass Inlet Nut in Lieu of Standard Anodized Aluminum 4 Straight 1.5” FNST Swivel Foam/Chemical Inlet Port (Not recommended for HF1.5) 5 Straight 1.5” FNPT Rigid Foam/Chemical Inlet Port (Standard on HC - Not recommended for HF1.5) 6 Male Cam-Lock Foam/Chemical Inlet Port (Same as Standard Size for Nozzle Configuration) 7 Manual ON/OFF 1-3% Metering Valve A Automatic w/Maximum Flow Stop (Requires Engineering Approval) F Fixed Flow Maximum Stop Non-Automatic (Requires Engineering Approval) X Special (Requires Engineering Approval)

NOTE: All “X” Selections Require Engineering Approval Prior to Ordering —

A Detailed Description Must be Provided When Placing Order

Ranger™ AUTOMATIC NOZZLEHF / HC / MS PART NUMBERING SYSTEM


63/100

Monitor Nozzles

Product:Monitor Nozzle - “BTM” Series

Description:Standard industrial grade master stream nozzle. Fully adjustable from

straight stream to full fog. Cast brass construction. Standard flow rates of 350,500, and 700 gpm at 100 psi nozzle pressure. As an option, nozzle can be fac-tory modified to any flow between 100 to 700 gpm at 100 psi (i.e. any K Factor

between 10 and 70). Abbreviated style cast control handles. Standard jam nutlocks foam or water stream at desired pattern. 2.5” NH (F) rigid inlet.

Model Flow @100 psi K-Factor InletRange Straight

StreamMaterial

BTM-350 350 35 2.5” NH (F) 150 ft. Cast Brass




64/100

Monitor Nozzles

Product:Premium Monitor Nozzle - “Big Tee”

Description:Premium grade industrial master stream nozzle with exclusive

“flush” feature. In flush position, nozzle will purge particulates up.gof lluf otmaer tsthgiar tsmor f el batsu jdaylluF.r etemaid”52.ot

Large composite rubber covered brass handles for positive streamcontrol. All brass construction. Standard flow rates are 350 and500 at 100 psi nozzle pressure.

Model Flow @100 psi K-Factor Inlet Range StraightStream

Material

BT-350 350 gpm 35 2.5” NH (F) Swivel 135 ft. Cast Brass

BT-500 500 gpm 50 2.5” NH (F) Swivel 150 ft. Cast Brass


65/100

Monitor Nozzles

Product:High Volume Monitor Nozzle - WBB “Big Boy”

Description:High-volume, industrial-grade, master stream nozzle. Fully adjust-

able from straight stream to full fog. Cast brass construction. Standardflow rates of 750, and 1000 gpm at 100 psi. Abbreviated style castcontrol handles. Standard jam nut locks foam or water stream at desired

pattern. Available with either 2.5” or 3.5” NH (F) inlet.

Model Flow @100 psi K-Factor Inlet(s) Range StraightStream

Material

WBB-750 750 gpm 75 2.5” / 3.5” NH (F) 175 ft. Cast BrassWBB-1000 1000 gpm 100 2.5” / 3.5” NH (F) 200 ft. Cast Brass


66/100


Product:

Hydro-Foam™ Monitor Nozzles —Small Body LW Series

Description:Patented water powered nozzle system that proportions and delivers

either water or foam to the hazard area. Fully adjustable from straightstream to full fog with flows of 150 or 225 gpm. Brass construction withstainless steel trim. Foam is proportioned directly from an atmosphericsource at 1%, 3% or 6%.


Model #Hydro-Foam™

Nozzle

Flow@100psi

Range@100psi(straightstream)

Range@100psi(narrow fog)

Water inlet Concentrateinlet

K-factor Proportioning

Small Body

LW150

150 gpm 110 ft. 60 ft. 1.5”NH

(F)swivel

1”NPT(M) 15 1%, 3% or 6%

Small BodyLW225

225 gpm 115 ft. 65 ft. 1.5”NH

(F)swivel

1”NPT(M) 22.5 1%, 3% or 6%


67/100


Product:

Hydro-Foam™ Monitor Nozzles —

Medium Body HF Series - Elkhart

Description:Patented water powered nozzle system that proportions and delivers either water

or foam to the hazard area. Fully adjustable from straight stream to full fog withflows of 350 or 500 gpm. Brass construction with stainless steel trim. Nozzle comescomplete with 1” X 8 ft. flexible pick-up hose. Optional 1% or 3% selector providesdual proportioning capability. Foam concentrate is proportioned directly from anatmospheric source.


Nozzle

Flow@100psi

Range@100psi(straightstream)

Range@100psi

(narrow fog)

Waterinlet

Concentrateinlet

K-fact or P ro po rt ion in g

HF 350 350 gpm 145 ft. 65 ft. 2.5”NH(F)swivel

1”NPT(M) 35 1%, 3%

HF 500 500 gpm 155 ft. 75 ft. 2.5”NH(F)swivel

1”NPT(M) 50 1%, 3%


68/100


Product:

Hydro-Foam™ Monitor Nozzles —

Medium Body LW 700

Description:Patented water powered nozzle system that proportions and delivers

either water or foam to the hazard area. Fully adjustable from straightstream to full fog with a flow of 700 GPM @100 PSI. Brass constructionwith stainless steel trim. 1% or 3% proportioning. Nozzle is supplied witha 1” x 8 ft. flexible pick-up hose. Foam is proportioned directly from anatmospheric storage tank.



Nozzle

Flow@100psi

Range @100psi(straight stream)

Waterinlet

Concentrateinlet

K -fact or Pr opo rt ion in g

Medium BodyLW700

700 gpm 160 ft. 2.5”NH

(F)swivel

1”NPT(M) 70 1% or 3%


69/100


Product:

Hydro-Foam™ Monitor Nozzles Medium Body LWNS 350, 500 & 750

Description:Patented water powered nozzle system that proportions and delivers either

water or foam to the hazard area. Fully adjustable from straight stream tofull fog. Brass construction with stainless steel trim. Flows 350, 500 or 750gpm @100 psi, with 1% or 3% (6% @ 350 and 500 gpm) proportioning. Anoptional 1% / 3% (3% / 6% @ 350 and 500 gpm) selector valve provides dual

proportioning. Foam concentrate is proportioned directly from an atmosphericstorage tank or from a remote foam concentrate supply in conjunction with amatched Jet Ratio Controller at 1% or 3% only. Nozzle is supplied with 1.5”X 8 ft. flexible pick-up hose.


ModelHydro-Foam™ Nozzle

LWNS 350 LWNS 500 LWNS 750

Nominal Flow @100psi 350 gpm 500 gpm 750 gpm

Nominal Range @ 100psi

(straight stream)

135 ft. 150 ft. 160 ft.

Water Inlet 2.5”NH (F) Swivel 2.5”NH (F) Swivel 2.5”NH (F) Swivel

Foam Concentrate Inlet 1.5” NPT(M) 1.5” NPT(M) 1.5” NPT(M)

Proportioning 1% / 3% / 6% 1% / 3% / 6% 1% / 3%


70/100

Handline Nozzles

Product:

HYDROJET HANDLINE NOZZLES

Viper Select Series

Description:Superior quality fire fighting handline nozzles. Created from performance data gained through extensive research, as well

as from actual field exposure on a multitude of large “fires in anger.”

• Multiple Gallonage/Constant Flow design.• Compact and Lightweight Design in Extruded “E-Lite” Alloy.• Molded Composite Rubber Pistol Grip for Precise Control.• Durable Construction Provides Superior Impact Resistance.

Standard Features Include:» Constant Flow feature Allows for use with Matched Foam Eductor.» Factory Installed spinning teeth for Maximum Stream Break-up.» Combination Full Fog to Straight Stream.» Independent Pattern Selection with Indication.» Heavy Duty Rubber Bumper.» Fully Machined Waterway for Flow Efficiency.» Excellent for use with ThunderStorm® ATC Foam Concentrates.» Horseshoe Shutoff Provides Positive Flow Control.» Change Flow without Changing Pattern.» Full Flush Feature.

ModelHydroJet Nozzle

Nominal Flow Inlet Length Weight

SG-3012 30,60,95,125 1.5” NH (F) 8.9” 4.25 lbs.

SG-7515 75,100,125,150 1.5” NH (F) 8.9” 4.25 lbs.

SG-9520 95,125,150,200 1.5” NH (F) 10.6” 6.5 lbs.


71/100

Handline Nozzles

Product:HYDROJET HANDLINE NOZZLES

Viper Select Series

Standard Viper NozzleSG-3012

SG-7515

Viper Midrange Nozzle

SG-9520


72/100

Air Aspirating Foam Nozzle

Model AFN-1

Nozzle Flow and Range Range at Range at Range at Range atPressure Flow Rate 30° Elev. 22.5° Elev. 15° Elev. 0° Elev.psi (kPa) gpm (Lpm) ft. (m) ft. (m) ft. (m) ft. (m)_________ __________ ________ ________ ________ ________ 50 (345) 385 (1457) 135 (41) 135 (41) 115 (35) 50 (15)100 (690) 534 (2021) 175 (53) 175 (53) 170 (52) 80 (24)150 (1034) 656 (2483) 190 (58) 190 (58) 190 (58) 100 (30)

NOTE: Above based on orifice sized for 500 gpm @ 100 psi (1893 Lpm @ 690 kPa).

General DescriptionConstructed of hard anodized aluminum with stainless steel fasteners

and adjustment rod, this air aspirating foam nozzle offers minimum weight

with durability. Stream pattern is adjustable in the field from an even fan type

to a full straight stream.

Flow rates are specifically tailored to individual protection by the inser-

tion of a pre-engineered stainless steel orifice plate.

Orifice plates can be sized for flows from 250 to 1000 gpm (946 to

3785 Lpm) within K-factors of 35 to 125 based on flowing nozzle inlet pres-

sure. (Monitor friction loss must be deducted from monitor inlet pressure to

use those K-factors.)

Connector is a female swivel, 2.5” – 7.5” TPI NHT.

Ordering InformationPart No. Description

400200 AFN-1 Nozzle

400336 r otar e pOr eveLhtiwelzzo NM1- NFA

400380 AFN-1-SS Stainless Steel Nozzle

400326 leetSsselniatSSS-M1- NFA

AFN- 1 N ozzle

48.125“

(122.2 cm)

2.5“ - 7.5 NHT

Swivel Coupling

4.5” (11.4 cm)

Diameter

Adjustable Control

RodAdjustable Jaws

48.125“

(122.2 cm)

2.5“ - 7.5 NHT

Swivel Coupling

4.5” (11.4 cm)

Diameter

Lever Operator

Adjustable Jaws

Control Rod

AFN- 1 N ozzle


73/100

Air Aspirating Handline Nozzles

Features• niesUr of noitcur tsnoCleetSsselniatS

Corrosive Environments• m pg021r o,59,06f osetaR wolFlanimo N

(227, 360, or 454 Lpm)• dna,59-LP,06-LPlusnAhtiwel bita pmoC

PL-120 Line Proportioners• el baliavAf f otuhS pir G-lotsiPlanoit pO

(Anodized Aluminum)• mumixaMr of ngiseDel batr oP,thgiewthgiL

Mobility

ApplicationAnsul (HL) foam handline nozzles can be used with all low expansion foam agents: protein foam, fluoroprotein foam,

and AFFF. These portable, air aspirating nozzles can be used in a variety of flammable liquid hazard areas. Typical applica-tions include use by municipal fire departments and crash-fire-rescue vehicles; or for handline applications around tank farms,loading racks, aircraft hangars, and chemical plants.

DescriptionAnsul handline nozzles are available in three sizes (HL-60, HL-95, and HL-120) with or without pistol-grip shutoff. The

nozzles are constructed of stainless steel; the pistol-grip shutoff is anodized aluminum. Lightweight and compact, they maxi-mize fire fighting mobility and ease of use.

Ordering InformationThe models listed below are provided with 1.5” NHT female inlet threads. Other thread types are available upon request.

The flow rates listed are nominal; see Flow Rate Data for actual flow rates based on inlet pressure.

Typical Foam Quality/Range Data

Protein/ Fluoro- protein AFFF 3% ARC ______ ____ _______

Foam 8:1 10:1 7:1ExpansionRatio

Drain Time 7 min. 3 min. 8 min.(25%)

Stream Range 50 ft. 50 ft. 50 ft.@ 50 psi (15.2 m) (15.2 m) (15.2 m) (345 kPa)



Hose Length/Size Data

Maximum Hose HoseHandline Line Size Length* Nozzle Proportioner in. ft. (m) _____ __________ ____ ________

HL-60 PL-60 1.5” 200 (61.0)

HL-95 PL-95 1.5” 100 (30.5)

HL-120 PL-120 1.5” 100 (30.5)

.r enoitr o por penilevo ba)m4.2(.tf 8f omumixamadetavelegnie belzzonnodesa bsihtgnelesohmumixaM*

ApproxShipping

Part Weight No. Description lb. (kg)

77796* HL-60 Nozzle 5 (2.3)without Shutoff,

60 gpm (227 Lpm)

77792* HL-60S Nozzle 7 (3.2)with Shutoff,

60 gpm (227 Lpm)

ApproxShipping

Part Weight No. Description lb. (kg)

77797* HL-95 Nozzle 5 (2.3)without Shutoff,

95 gpm (360 Lpm)

77793* HL-95S Nozzle 7 (3.2) with Shutoff, 95 gpm (360 Lpm)

Approx ShippingPart Weight No. Description lb. (kg)

77981 HL-120 Nozzle 5 (2.3)without Shutoff,

120 gpm (454 Lpm)

78419 HL-120S Nozzle 7 (3.2)with Shutoff,

23.1”

(58.7 cm)

19”

(48.3 cm)

19”

(48.3 cm)

Optional

Shutoff

Nozzle

2.5”

(6.4 cm)3”

(7.6 cm)


74/100

Flow Rate Data

001224

(kPa) psi ____ ___ HL-60 HL-95 HL-120 (1034) 150

(827) 120

(690) 100

(621) 90

(552) 80

(483) 70

(414) 60

(345) 50

(276) 40 40 50 60 70 80 90 100 120 150 gpm (151) (189) (227) (265) (303) (341) (379) (454) (568) (Lpm)

FLOW RATE

I N L E T

P R E S S U R E

Air Aspirating Handline Nozzles


75/100

Foam Nozzles

Product:Foam Wand

Description:The Foam “Wand” is designed to expand and deliver foam into remote/

hazardous areas where either logistics or safety considerations dictate thatthe foam nozzle be “unattended.” The “wand” delivers high quality foamonto hard-to-access flammable liquid fires. Flow rate is 95 gpm @ 100

psi (K=9.5). Works in conjunction with a standard 95 gpm inline educ-tor or other foam proportioning system. Nominal foam expansion is 4:1. Assembly includes 1.5” NH (F) brass swivelfoam solution inlet; carbon steel distribution pip-ing; foam nozzle; detachable horizontal “stand-

off”, canvas carrying case.

Typical Application

Foam Wand assembly

ModelFoam Wand

Nominal Flow@ 100 PSI

K-factor Inlet Body

95 gpm 95 gpm 9.5 1.5” NH(F) Swivel Schedule 40

Carbon Steel


76/100

Balanced Pressure Proportioning Systems

Product:

Spectrum Bladder Tanks-Horizontal Configuration

Description:Spectrum Horizontal Bladder tanks provide dependable and cost

effective foam fire protection for a wide variety of flammable/combustibleliquid hazards. Used in conjunction with either one, or multiple ratio flowcontrollers (installed adjacent to the tank), the all-hydraulic balanced pres-sure proportioning system stores, delivers and proportions foam withoutdependence on external foam concentrate pumping. Only water under

pressure is required for system operation.

The Spectrum Horizontal Bladder Tank is a cylindrical carbon steelASME pressure vessel containing a flexible polymeric elastomer inner bladder which encapsulates the foam concentrate. This bladder physically separates stored foam concentrate from the water supply. When the system is activated, water is directedinto the tank shell, which then pressurizes the space between the flexible bladder and the interior tank wall. This water pres-sure causes the bladder to collapse, which then dispenses foam concentrate out through distribution piping and (ultimately)into the ratio controller(s). The ratio controller’s modified venturi creates a “metering pressure drop” in the fire water line,allowing foam concentrate to pass through a fixed orifice plate and enter the fire water piping at the designated proportioningrate. In installations where the bladder normally is under pressure (wet pipe, reaction, or when the deluge valve is downstreamfrom the ratio controller), a normally-closed actuated concentrate valve (electric or hydraulic) isolates the foam concentrateuntil energized. Interior/exterior finished in red enamel.

Standard Spectrum Bladder tank trim includes:

1. ASME Code Pressure Vessel

2. Flexible Concentrate Bladder

3. Shell Side (water) Vent Valve

4. Bladder (concentrate) Vent Valves

5. Shell Side (water) Fill/Drain Valve

6. Bladder (concentrate) Fill/Drain Valve

7. Water Balancing Nozzle (screened)

8. Vessel Skirt with Anchors

9. Concentrate Discharge Pipe, Perforated10. Concentrate Discharge Nozzle

11. Lifting Lugs included (not shown)

Spectrum Bladder Options:

12. Sight Gauge Assembly

13. Epoxy Interior/Exterior Finish (For use in

marine or corrosive environments)

14. Pressure Relief Valve (Not Shown)


77/100


78/100


79/100

Foam Concentrate Tanks

Product:

Vertical Polyethylene Storage Tanks

Description:Atmospheric High Density, Cross-Linked Polyethylene Storage Tanks are

an industry standard for storing foam concentrate. They are typically used inconjunction with pumped balanced pressure systems or self-educting Hydro-Foam™ monitor stations. Polyethylene is an exceptionally stable and durablematerial when used to store foam concentrates. These rotationally molded,corrosion/impact resistant upright tanks are available in nominal storagecapacities ranging from 55 to 12,000 gallons.

Bill of Materials

1 Pressure Vacuum Vent.

2 PVC Bulkhead Fitting.

3 10” Threaded Inspect Hatch (tank sizes

up to 400 gallons).

4 19” Bolted Manway (tank sizes >400 gal -

lons).

5 Top Mounted Fill Connection with PVC

Drop Tube (option).

6 Liquid Level Indication-Molded.

7 Tank Drain/Fi ll Fi tt ing, Stainless Steel

Valved.

8 Pump Supply Fittings, Stainless Steel

with Siphon Pickup.

9 Return Fitting, Stainless Steel with

Siphon Discharge.

10 Fittings (only) for tank liquid level con-

tacts.

Ver ticalPoly Tank

Material

Pigments,

Vapor Space Fittings

Fittings,

Liquid Space

Liquid Level

Indication

High Density

Cross Linked

Polyethylene


80/100


81/100


Product:

Horizontal Polyethylene Storage Tanks

Description:Atmospheric High Density, Cross-Linked Polyethylene

Storage Tanks are an industry standard for storing foam con-centrate. They are typically used in conjunction with trans-

portable foam trailers, pumped balanced pressure systems orself-educting Hydro-Foam™ monitor stations. Polyethyleneis an exceptionally stable and durable material when usedto store foam concentrates. These rotationally molded,

corrosion/impact resistant horizontal/cylindrical tanks areavailable in sizes ranging from 110 gallons to 2,500 gal-lons. Tanks are mounted on carbon steel support saddles andsecured with support bands.

Bill of Materials

1 Pressure Vacuum Vent.

2 PVC Bulkhead Fitting.

3 10” Threaded Inspect Hatch (tank sizes <

1000 gallons).

4 19” Bolted Manway (tank sizes >1000 gal-

lons).

5 Top Mounted Fill Connection with PVC Drop

Tube (option).

6 Liquid Level Indication-Molded.

7 Tank Drain/Fill Fitting, Stainless Steel Valved.

8 Pump Supply Fittings, Stainless Steel withSiphon Pickup.

9 Tank Return Fitting, Stainless Steel with

Siphon Discharge.

10 Tank Return Fitting, Stainless Steel with

Siphon Discharge.

11 Fittings (only) for tank liquid level contacts.

Horizontal PolyTank

Material PigmentsFittings,

Vapor Spac eFittings,

Liquid SpaceLiquid LevelIndication

High DensityCross Linked

Polyethylene


82/100


Horizontal Polyethylene Storage Tanks- Dimensional Data

Tank Configuration “A” (150-1000 Gallon Capacity)

Support Saddle “A1” - (150-500 Gallon Capacity)

Support Saddle “A2” - (750-1000 Gallon Capacity)

NominalCapacity

(US Gallons)

Diameter Length TotalWeight

FillOpening

150 28” 410” 190 10”

200 x 32” 28” 58” 245 10”

200 x 38” 32 44” 245 10”

300 32 63” 305 10”

400 4 53” 330 10”

500 4 64” 350 10”

750 46” 71.5” 585 10”

1000 54” 72” 770 10” or 19”

Tank Size Width Length

150 31.5” 48”

200 x 32” 31.5” 60”

200 x 38” 37.5” 38.5”

300 37.5” 60”

400 48” 48”

500 48” 50”


750 48.5” 65”

1000 57” 60”


83/100


Horizontal Polyethylene Storage Tanks- Dimensional Data

Tank Configuration “B” (1025-2500 Gallon Capacity)

Support Saddle “B”

Nominal Capacity(US Gallons)

Diameter Length Total Weight Fill Opening

1025 4 124” 1065 19”

1625 54” 113” 1433 19”

2000 54” 131” 1550 19”

2500 54” 1511” 1942 19”


1025 38.75” 910

1625 410” 93”

2000 410” 10

2500 410” 146”


84/100

Foam Systems - Around The Pump Eductors

Product:Spectrum ATP Eductors, 2” & 3” - Grooved Type

Description:The Spectrum Around The Pump Eductor is a fundamental, eco-

nomical, yet proven way to produce foam on a fire truck. In operation a portion of the fire water discharge is diverted to the eductor. The educ-tor picks up foam concentrate from the on-board atmospheric foam tankand delivers it to the suction side of the water pump. A metering valvesuch as the Spectrum Multiport Metering Valve controls the amount ofconcentrate entering the system. This, along with the rate of discharge,determines the solution flow rate; typically from 1% to 6%. All dis-charges in this type of system will produce foam solution. Eductors are

constructed of brass to provide years of trouble free service.

*Minimum straight pipe lengths

required upstream of controller

Minimum Operating Pressure = 75 psiMaximum Operating Pressure = 225 psi

2” 3”

A 7.5” 10”

B 3.875” 5.0625”

C 2.8125” 2.6875”

D 2.625” 3.3125”

E 1.5” 2”

F 2” 3”

G 10” 15”

Part #Ratio

Controller SizeConfiguration

NominalConcentrate Flow

MaximumProportioning

Rates (gpm)Drive Water

Flow @ 200 psi

3% 6%

2.0EDCT-75 2” Grooved 75 gpm 2500 1250 85 gpm

3.0EDCT-150 3” Grooved 150 gpm 5000 2500 150 gpm


85/100

Foam Systems - Multi Port Metering Valve

Product:

Spectrum

08-miscelaneo-catalogo productos final 2016 v2 liv

Documents