1 2 3 4 in the `approved'-field. · 2018. 5. 10. · d 240 c)540 240 c)540 e 30 c) 36 30 c) 36...
TRANSCRIPT
This document is issued by means of
a computerized system.
The digitally stored original is ele
ctronically approved. The
approved document has a date entered
in the `Approved'-field.
A manual signature is not required.
Drawing sheet ISO 5457-A4T rev A
We reserve all rights in this document and in the information contained
therein. Reproduction, use or disclosure to third parties without express
authority is strictly fobidden. © Copyright 2015 ABB. All rights reserved.
D
C
B
E
F
1 2 3 4
255 27
30
50
D
470
111 205
C
E
195
152
567
45
126
B
85 140
245
H
304
165
225
165
225490
255 255
98
6
60390
260
C/L Top flange80
332
740
24x 15
710
30 C/L Diverter switch
520
165 165
8x 1)18
K
J
95
95
250
272
A
552
140 250
C/L Tap selector
INSULATION380 1050 SHORT VERSION b)LEVEL kV 650 380,650
750 750 1050A 1906 a)2206 a)1686 a)1986 a)Dimen-
sionsin mm
B 1354 a)1654 a)1134 a)1434 a)C 119 a)c)119 a) 119 a)c)119 a)D 240 c) 540 240 c) 540 E 30 c) 36 30 c) 36H 930 c) 936 930 c) 936J 290 c) 293 290 c) 293K'580 c) 586 580 c) 586
1/2ENB54920101-9
SheetLanguageRevisionDocument Id.
UCG-E, T XXX/300-900/III 9,13 Pos
Tap-Changer UCGR, UCGD, UCG-B (1 Phase) XXX/300-600/III
Title
DIMENSION DRAWING PPCO/TK2015-05-28
Document KindResponsible departmentDate / Approved
1) Holes for mounting of supports for cleats and leads2) Shielding rings for insulation levels 650, 750 and 1050 only
T=6
H-1,3..13
2)
2021
Only for insulation level 1050 kV
4x �n�18 of which 2x at opposite side 1)
2)
Transformer flange a) For mounting on active part use A+106,B+106 and C+106 (See also Drawing 54920103-1)b) Short version means reduced switching capacity.Please refer to Technical Guidec) Not applicable for 380 kV
M-M
These two holesalso in top plate
V-2,4..12
R-R2x �n�18 1)
This document is issued by means of
a computerized system.
The digitally stored original is ele
ctronically approved. The
approved document has a date entered
in the `Approved'-field.
A manual signature is not required.
Drawing sheet ISO 5457-A4T rev A
We reserve all rights in this document and in the information contained
therein. Reproduction, use or disclosure to third parties without express
authority is strictly fobidden. © Copyright 2015 ABB. All rights reserved.
D
C
B
E
F
1 2 3 4
30�$�
30�$�
60�$�
22,5�$�
22,5�$�
45�$�
15
40
13
855
79
45
10
45 33,5
30
13
15
245 350
50�$�
50�$�
R282.5
R263
ADDITIONAL DRAWINGS:Connection Diagrams:See Technical Guide UCMounting on active part: 54920103-1Accessories:54920103-2Motor Drive BUL2:1ZSC004106-AAEMotor Drive BUE:54830001-2 or -3External Drive Shaft:54920083-4Pressure Relay:54920083-2Bevel Gear:54920083-1
2/2ENB54920101-9
SheetLanguageRevisionDocument Id.
UCG-E, T XXX/300-900/III 9,13 Pos
Tap-Changer UCGR, UCGD, UCG-B (1 Phase) XXX/300-600/III
Title
DIMENSION DRAWING PPCO/TK2015-05-28
Document KindResponsible departmentDate / Approved
1
89
1
1011
1213
22
20
21
22
20
21
T=14
Tap selector contact 20,21 and 22 with shields
9 positions
P-P
23
45
67
SEE DETAIL A
R282.5
R263
13 positions
P-P
23
45
67
89
Current collector
DETAIL A