11

Chang Shuan Electronics Co., LtdChang Shuan Electronics Co., Ltdhttp://www.csec.com.twhttp://www.csec.com.tw

http://www.adtek.com.twhttp://www.adtek.com.tw

22

ST SERIES FAMILYST SERIES FAMILY

33

ST Signal ST Signal TransmitterTransmitterST-VAST-VA Voltage / Current Controllers

0~600V / 0~10A for DC/AC/TRMS

ST-PRST-PR Linear Process Controllers 0~10V & 0(4)~20mA all in one

ST-SGST-SG Stain Gauge Controllers 1.0/2.0/4.0 ~ 10.0/20.0/40.0 mV/V1.0/2.0/4.0 ~ 10.0/20.0/40.0 mV/V

ST-PMST-PM PotentioMeter Controllers 0~2.0K / 0~50.0K ohm (3 Wired)0~2.0K / 0~50.0K ohm (3 Wired)

ST-TST-T Temperature Controllers Pt100Pt100 ohm / Thermocouple K,J,E,T,R,S,B.ohm / Thermocouple K,J,E,T,R,S,B.

ST-RL Linear Speed / Rotation Controllers 0.01~100KHz /~140KHz (Optional), NPN/PNP/Contact/Vp 0.01~100KHz /~140KHz (Optional), NPN/PNP/Contact/Vp /30~600Vp/30~600Vp

ST-LCST-LC Math (Math ( ＋－＋－ X ÷ ) X ÷ ) Conditioner with LED DisplayConditioner with LED Display 0~10V & 0(4)~20mA / 1.0/2.0/4.0 ~ 10.0/20.0/40.0 mV/V0~10V & 0(4)~20mA / 1.0/2.0/4.0 ~ 10.0/20.0/40.0 mV/V

Features of ST Features of ST seriesseries

1 relay output, Analogue output, and RS 485 Communication can be selected at same Meter 1 relay output Hi / Lo / Hi.HLd / Lo.HLd / doHi / Lo / Hi.HLd / Lo.HLd / do with Start Delay / Hysteresis / Energized & De-energized Delay / DO / with Start Delay / Hysteresis / Energized & De-energized Delay / DO / Relay Energized Hold….. Relay Energized Hold…..

Analogue outputAnalogue output Analogue High and Low settable as zoom-in functionAnalogue High and Low settable as zoom-in function Analogue output high limited functionAnalogue output high limited function

RS 485 portRS 485 port Address number 1~255, Baud Rate from 2400~38400 bpsAddress number 1~255, Baud Rate from 2400~38400 bps Showing data in display screen from Modbus RTU mode 06 functionShowing data in display screen from Modbus RTU mode 06 function

Display Present Value (PV) / Maximum or Minimum Hold / RS485 writing Present Value (PV) / Maximum or Minimum Hold / RS485 writing Low Cut, Average, Digital Filter, Scaling, Digital Fine adjustment…..Low Cut, Average, Digital Filter, Scaling, Digital Fine adjustment…..

1 Relay Output1 Relay Output Hi / Lo / Hi.HLd / Lo.HLd / doHi / Lo / Hi.HLd / Lo.HLd / do HiHi: High Limit Energized, when the PV >= Set-point: High Limit Energized, when the PV >= Set-point LoLo: Low Limited Energized , when the PV <= Set-point: Low Limited Energized , when the PV <= Set-point Hi.HLd (Lo.HLd): Hi.HLd (Lo.HLd): High (Low) Limit Energized continuously High (Low) Limit Energized continuously until manual reset by front key or External Control Input (ECI)until manual reset by front key or External Control Input (ECI) dodo: Relay energized according the RS485 command : Relay energized according the RS485 command

Hi or Lo Relay Energized Hi(Lo) Energized Hold & Reset

Hi Setting

Hi Relay Energized ON

Lo Setting

Lo Relay Energized ON

Hi Setting

Hi.HLd(High Hold) Relay Energized ON

Reset the relay Hold by ECI or Front Key

ON Level Trigger

77

Start Delay / Hystersis / Relay energized Start Delay / Hystersis / Relay energized delay / Relay De-energized delaydelay / Relay De-energized delay Start DelayStart Delay Hysteresis: Settable range from Hysteresis: Settable range from 0~9999 Counts0~9999 Counts Relay energized delay: Settable range from Relay energized delay: Settable range from 00.1(second)~9(minutes)59.9(seconds);.1(second)~9(minutes)59.9(seconds); Relay de-energized delay: Settable range from Relay de-energized delay: Settable range from 0.1(second)~9(minutes)59.9(seconds)0.1(second)~9(minutes)59.9(seconds)

Start Delay Energized / De-energized Delay & Hysteresis

Start Delay Time

Start Band(SB)

Hi Setting

Relay Energized ON

Inhibit

Inhibit Hi Setting

Ener

gize

d de

lay

time

Relay Energized ON

Hysteresis

De-

ener

gize

d de

lay

time

Analogue outputAnalogue output Accuracy:Accuracy: ≦≦ 0.1% of F.S.; 16 bits AD converter 0.1% of F.S.; 16 bits AD converter Response time:Response time: ≦≦200 msec. (10~90% of input) 200 msec. (10~90% of input) Isolation:Isolation: AC 2.0 KV between input and output AC 2.0 KV between input and output Functions: Functions: Ao.HiAo.Hi(output high): PV Hi vs. output range Hi(output high): PV Hi vs. output range Hi Ao.LoAo.Lo(output range Low): PV Low vs. output range Lo(output range Low): PV Low vs. output range Lo Ao.LMtAo.LMt(output High Limit):(output High Limit): 0.00~110.00% of output High0.00~110.00% of output High

SCALE Default: Ai.Lo: 0%, Ai.Hi: 100%; Lo.SC: 0.00, Hi.SC: 100.00 Change to Ai.Lo: 0%, Ai.Hi: 75%; Lo.SC: 0.00, Hi.SC: 199.99

0.00

199.99

100.00

0.00% 100.00% 50.00% INPUT 75.00% 0.00% 100.00% 50.00% OUTPUT

199.99

100.00

0.00

Setted Scaling: Lo.SC: 0.00, Hi.SC: 199.99; Desired Output: Ao.Lo: 50.00(PV), Ao.Hi: 150.00(PV)

50.00

150.00

SCALE

RS 485 port RS 485 port Modbus RTU ModeModbus RTU Mode AddressAddress: 1~255.: 1~255. Baud RateBaud Rate: 1200 / 2400 / 4800 / 9600 / 19200 / 38400 selectable. : 1200 / 2400 / 4800 / 9600 / 19200 / 38400 selectable. Parity:Parity: Even / Odd / None parity, 8 data bits, 1 stop bit / None Even / Odd / None parity, 8 data bits, 1 stop bit / None parity, 8 data bits, 2 stop bit selectable.parity, 8 data bits, 2 stop bit selectable. Can read External Control Input (ECI) statusCan read External Control Input (ECI) status Can send the data to display screen by Modbus commandCan send the data to display screen by Modbus command

1010

SpecificationSpecification ST-VA Measuring: Vdc, Vac, Adc, Aac) / 0~600V or 0~10AMeasuring: Vdc, Vac, Adc, Aac) / 0~600V or 0~10A Accuracy): DC: ± 0.04% F.S.± 1 count; AC: ± 0.1% F.S.± 1 count Accuracy): DC: ± 0.04% F.S.± 1 count; AC: ± 0.1% F.S.± 1 count Display: -19999~29999, 0.28” high bright LEDDisplay: -19999~29999, 0.28” high bright LED

ST-PR-PR Measuring: Measuring: 0~(5)10Vdc & 0(4)~20mAdc All in one0~(5)10Vdc & 0(4)~20mAdc All in one Accuracy: ± 0.04% F.S.± 1 countAccuracy: ± 0.04% F.S.± 1 count Display: -19999~29999, 0.28” high bright LEDDisplay: -19999~29999, 0.28” high bright LED ST-SG Measuring: Measuring: 0~1.0/~2.0/~4.0/~10.0/~20.0/~40.0mV/V specify0~1.0/~2.0/~4.0/~10.0/~20.0/~40.0mV/V specify Accuracy: ± 0.04% F.S.± 1 count Accuracy: ± 0.04% F.S.± 1 count Display: -19999~29999, 0.28” high bright LEDDisplay: -19999~29999, 0.28” high bright LED

1111

SpecificationSpecificationST-PM-PM Measuring: Measuring: 0.0~2.0KΩ/~100.0KΩ (3 wired)0.0~2.0KΩ/~100.0KΩ (3 wired) Accuracy: ± 0.04% F.S. ± 1 count Accuracy: ± 0.04% F.S. ± 1 count Display: -19999~29999, 0.28” high bright LEDDisplay: -19999~29999, 0.28” high bright LED ST-RS-RS Measuring: Measuring: 0.1~200Ω/~2000Ω/~20.0KΩ/~200.0KΩ (2 wired)0.1~200Ω/~2000Ω/~20.0KΩ/~200.0KΩ (2 wired) Accuracy: ± 0.04% F.S. ± 1 count Accuracy: ± 0.04% F.S. ± 1 count Display: -19999~29999, 0.28” high bright LED Display: -19999~29999, 0.28” high bright LED

ST-T-T Measuring: Measuring: Pt100Ω (3 wired) / Thermocouple K,J,E,T,R,S,B..Pt100Ω (3 wired) / Thermocouple K,J,E,T,R,S,B.. Accuracy): Accuracy): Pt100Ω:Pt100Ω: ± 0.1% F.S. ± 1 count ± 0.1% F.S. ± 1 count Thermocouple K,J,E,T: Thermocouple K,J,E,T: ± 0.2% F.S. ± 1 count ± 0.2% F.S. ± 1 count Thermocouple R,S,B: Thermocouple R,S,B: ± 0.3% F.S. ± 1 count± 0.3% F.S. ± 1 count Display: -19999~29999, 0.28” high bright LED Display: -19999~29999, 0.28” high bright LED

1212

SpecificationSpecification ST-RL-RL Measuring: 0~100KHz(140KHz max.), decimal point auto setMeasuring: 0~100KHz(140KHz max.), decimal point auto set Accuracy: ± 0.005% F.S. ± 1 count Accuracy: ± 0.005% F.S. ± 1 count Display: 0~99999, 0.28” high bright LED Display: 0~99999, 0.28” high bright LED Input mode: NPN / PNP / Vp Input mode: NPN / PNP / Vp changeable by Dip Switch on top pcbchangeable by Dip Switch on top pcb

ST-LC-LC Measuring: Measuring: 2 inputs (internal isolated) 2 inputs (internal isolated) 0~(5)10Vdc / 0(4)~20mAdc specify0~(5)10Vdc / 0(4)~20mAdc specify 0~1.0/~2.0/~4.0/~10.0/~20.0/~40.0mV/V specify; selectable 2 0~1.0/~2.0/~4.0/~10.0/~20.0/~40.0mV/V specify; selectable 2 different input signalsdifferent input signals Accuracy: ± 0.04% F.S. ± 1 count Accuracy: ± 0.04% F.S. ± 1 count Display: -19999~29999/99999(mathematic), 0.28” high bright LED Display: -19999~29999/99999(mathematic), 0.28” high bright LED

1313

ApplicationsApplications

AO AL

RS 485

mVdc信號輸出

電流分流器

ENT ◄ ◄ ◄ ENT

MULTI-FUNCTION CONVERTER

M.H. D.H. COM RL

Measuring Input

1414

ApplicationsApplications ST-SERIES APPLICATION FOR VOLTAGE / CURRENT & FREQUENCY MEASURING

RS 485 Modbus RTU Mode (up to 38400bps)

1 Relay Output: Mode: High or Low Energized / Energized Hold / DO Functions: Start delay / Energized & De-energized

delay / Hysteresis

Analog Output 0~10V/ 0(4)~20mA

Display: Mode: Measuring Value / Maximum Hold / Minimum

Hold / Reading value from RS485 command

電流分流器 馬達 配電盤

ENT

◄ ◄ ◄ ENT

MULTI-FUNCTION CONVERTER

M.H. D.H. COM RL

ENT

◄ ◄ ◄ ENT

MULTI-FUNCTION CONVERTER

M.H. D.H. COM RL

ENT

◄ ◄ ◄ ENT

MULTI-FUNCTION CONVERTER

M.H. D.H. COM RL