100370254 boilers and thermic fluid heaters

1

Training Session on Energy Training Session on Energy EquipmentEquipment

Boilers & Thermic Boilers & Thermic Fluid HeatersFluid Heaters

Presentation from the“Energy Efficiency Guide for Industry in Asia”

www.energyefficiencyasia.org

©© UNEP 2006 UNEP 2006

Ther m

al Equipm

ent/B

oil ers

2

Ther m

al Equipm

ent/B

oil ers

Introduction

Type of boilers

Assessment of a boiler

Energy efficiency opportunities

©© UNEP 2006 UNEP 2006

Training Agenda: BoilerTraining Agenda: Boiler

3

Ther m

al Equipm

ent/B

oil ers

What is a Boiler?

©© UNEP 2006 UNEP 2006

IntroductionIntroduction

• Vessel that heats water to become hot water or steam

• At atmospheric pressure water volume increases 1,600 times

• Hot water or steam used to transfer heat to a process

4

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006

IntroductionIntroduction

BURNERBURNERWATER WATER

SOURCESOURCE

BRINEBRINE

SOFTENERSSOFTENERSCHEMICAL FEEDCHEMICAL FEED

FUELFUELBLOW DOWN BLOW DOWN SEPARATORSEPARATOR

VENTVENT

VENTVENTEXHAUST GASEXHAUST GASSTEAM TO STEAM TO PROCESSPROCESS

STACKSTACK DEAERATORDEAERATOR

PUMPSPUMPS

Figure: Schematic overview of a boiler room

BOILERBOILER

ECO-ECO-NOMI-NOMI-ZERZER

5

Ther m

al Equipm

ent/B

oil ers

Introduction

Type of boilers



©© UNEP 2006 UNEP 2006


6

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006

Types of BoilersTypes of Boilers

1. Fire Tube Boiler

2. Water Tube Boiler

3. Packaged Boiler

4. Fluidized Bed (FBC) Boiler

5. Stoker Fired Boiler

6. Pulverized Fuel Boiler

7. Waste Heat Boiler

8. Thermic Fluid Heater (not a boiler!)

What Type of Boilers Are There?

7

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006

Type of BoilersType of Boilers

(Light Rail Transit Association)

1. Fire Tube Boiler

• Relatively small steam capacities (12,000 kg/hour)

• Low to medium steam pressures (18 kg/cm2)

• Operates with oil, gas or solid fuels

8

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


2. Water Tube Boiler

(Your Dictionary.com)

• Used for high steam demand and pressure requirements

• Capacity range of 4,500 – 120,000 kg/hour

• Combustion efficiency enhanced by induced draft provisions

• Lower tolerance for water quality and needs water treatment plant

9

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


(BIB Cochran, 2003)

3. Packaged Boiler

Oil Burner

To Chimney

• Comes in complete package

• Features• High heat transfer• Faster evaporation • Good convective

heat transfer• Good combustion

efficiency• High thermal

efficiency

• Classified based on number of passes

10

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


4. Fluidized Bed Combustion (FBC) Boiler• Particles (e.g. sand) are suspended in high

velocity air stream: bubbling fluidized bed

• Combustion at 840° – 950° C

• Capacity range 0,5 T/hr to 100 T/hr

• Fuels: coal, washery rejects, rice husk, bagasse and agricultural wastes

• Benefits: compactness, fuel flexibility, higher combustion efficiency, reduced SOx & NOx

11

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


4a. Atmospheric Fluidized Bed Combustion (AFBC) Boiler

• Most common FBC boiler that uses preheated atmospheric air as fluidization and combustion air

4b. Pressurized Fluidized Bed Combustion (PFBC) Boiler

• Compressor supplies the forced draft and combustor is a pressure vessel

• Used for cogeneration or combined cycle power generation

12

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


(Thermax Babcock & Wilcox Ltd, 2001)

4c. Atmospheric Circulating Fluidized Bed Combustion (CFBC) Boiler

• Solids lifted from bed, rise, return to bed

• Steam generation in convection section

• Benefits: more economical, better space utilization and efficient combustion

13

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


5. Stoke Fired Boilers

a) Spreader stokers

• Coal is first burnt in suspension then in coal bed

• Flexibility to meet load fluctuations

• Favored in many industrial applications

14

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


5. Stoke Fired Boilers

b) Chain-grate or traveling-grate stoker

(University of Missouri, 2004)

• Coal is burnt on moving steel grate

• Coal gate controls coal feeding rate

• Uniform coal size for complete combustion

15

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


Tangential firing

6. Pulverized Fuel Boiler

• Pulverized coal powder blown with combustion air into boiler through burner nozzles

• Combustion temperature at 1300 -1700 °C

• Benefits: varying coal quality coal, quick response to load changes and high pre-heat air temperatures

16

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


Agriculture and Agri-Food Canada, 2001

7. Waste Heat Boiler• Used when waste heat

available at medium/high temp

• Auxiliary fuel burners used if steam demand is more than the waste heat can generate

• Used in heat recovery from exhaust gases from gas turbines and diesel engines

17

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


8. Thermic Fluid Heater

• Wide application for indirect process heating

• Thermic fluid (petroleum-based) is heat transfer medium

• Benefits:

• Closed cycle = minimal losses

• Non-pressurized system operation at 250 °C

• Automatic controls = operational flexibility

• Good thermal efficiencies

18

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


(Energy Machine India)

8. Thermic Fluid Heater

Control panel

Blower motor unit

Fuel oil filter

Exhaust

Insulated outer wall

1. Thermic fluid heated in the heater

2. Circulated to user

equipment

User equipment

3. Heat transfer through heat exchanged

4. Fluid returned to

heater

19

Ther m

al Equipm

ent/B

oil ers

Introduction

Type of boilers



©© UNEP 2006 UNEP 2006


20

Ther m

al Equipm

ent/B

oil ers

1. Boiler

2. Boiler blow down

3. Boiler feed water treatment

©© UNEP 2006 UNEP 2006

Assessment of a boilerAssessment of a boiler

21

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006

Assessment of a BoilerAssessment of a Boiler

1. Boiler performance• Causes of poor boiler performance

-Poor combustion-Heat transfer surface fouling-Poor operation and maintenance-Deteriorating fuel and water quality

• Heat balance: identify heat losses

• Boiler efficiency: determine deviation from best efficiency

22

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


Heat BalanceAn energy flow diagram describes geographically how energy is transformed from fuel into useful energy, heat and losses

StochiometricExcess AirUn burnt

FUEL INPUT STEAM OUTPUT

Stack Gas

Ash and Un-burnt parts of Fuel in Ash

Blow Down

Convection & Radiation

23

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


Heat BalanceBalancing total energy entering a boiler against the energy that leaves the boiler in different forms

Heat in Steam

BOILER

Heat loss due to dry flue gas

Heat loss due to steam in fuel gas

Heat loss due to moisture in fuel

Heat loss due to unburnts in residue

Heat loss due to moisture in air

Heat loss due to radiation & other unaccounted loss

12.7 %

8.1 %

1.7 %

0.3 %

2.4 %

1.0 %

73.8 %

100.0 %

Fuel

73.8 %

24

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


Heat Balance

Goal: improve energy efficiency by reducing avoidable losses

Avoidable losses include:

- Stack gas losses (excess air, stack gas temperature)

- Losses by unburnt fuel

- Blow down losses

- Condensate losses

- Convection and radiation

25

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


Boiler EfficiencyThermal efficiency: % of (heat) energy input that is effectively useful in the generated steam

BOILER EFFICENCY CALCULATION

1) DIRECT METHOD: 2) INDIRECT METHOD:

The efficiency is the different between lossesand energy input

The energy gain of theworking fluid (water and steam) is compared with the energy content of the boiler fuel.

26

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


hg -the enthalpy of saturated steam in kcal/kg of steam

hf -the enthalpy of feed water in kcal/kg of water

Boiler Efficiency: Direct Method

Boiler efficiency () = Heat Input

Heat Outputx 100 Q x (hg – hf)

Q x GCVx 100=

Parameters to be monitored: - Quantity of steam generated per hour (Q) in kg/hr - Quantity of fuel used per hour (q) in kg/hr- The working pressure (in kg/cm2(g)) and superheat

temperature (oC), if any - The temperature of feed water (oC) - Type of fuel and gross calorific value of the fuel (GCV) in

kcal/kg of fuel

27

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


Advantages• Quick evaluation• Few parameters for computation • Few monitoring instruments• Easy to compare evaporation ratios with

benchmark figures

Disadvantages• No explanation of low efficiency• Various losses not calculated

Boiler Efficiency: Direct Method

28

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


Efficiency of boiler () = 100 – (i+ii+iii+iv+v+vi+vii)

Boiler Efficiency: Indirect Method

Principle losses:i) Dry flue gas

ii) Evaporation of water formed due to H2 in fuel

iii) Evaporation of moisture in fuel

iv) Moisture present in combustion air

v) Unburnt fuel in fly ash

vi) Unburnt fuel in bottom ash

vii) Radiation and other unaccounted losses

29

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


Boiler Efficiency: Indirect MethodRequired calculation data• Ultimate analysis of fuel (H2, O2, S, C, moisture

content, ash content)

• % oxygen or CO2 in the flue gas

• Fuel gas temperature in ◦C (Tf)

• Ambient temperature in ◦C (Ta) and humidity of air in kg/kg of dry air

• GCV of fuel in kcal/kg

• % combustible in ash (in case of solid fuels)

• GCV of ash in kcal/kg (in case of solid fuels)

30

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


Boiler Efficiency: Indirect Method

Advantages• Complete mass and energy balance for each

individual stream• Makes it easier to identify options to improve

boiler efficiency

Disadvantages• Time consuming• Requires lab facilities for analysis

31

Ther m

al Equipm

ent/B

oil ers


• Controls ‘total dissolved solids’ (TDS) in the water that is boiled

• Blows off water and replaces it with feed water

• Conductivity measured as indication of TDS levels

• Calculation of quantity blow down required:

2. Boiler Blow Down

Blow down (%) = Feed water TDS x % Make up water

Maximum Permissible TDS in Boiler water

©© UNEP 2006 UNEP 2006

32

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


Two types of blow down

• Intermittent• Manually operated valve reduces TDS• Large short-term increases in feed water• Substantial heat loss

• Continuous• Ensures constant TDS and steam purity• Heat lost can be recovered• Common in high-pressure boilers

Boiler Blow Down

33

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


Benefits

• Lower pretreatment costs

• Less make-up water consumption

• Reduced maintenance downtime

• Increased boiler life

• Lower consumption of treatment chemicals

Boiler Blow Down

34

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


• Quality of steam depend on water treatment to control• Steam purity

• Deposits

• Corrosion

• Efficient heat transfer only if boiler water is free from deposit-forming solids

3. Boiler Feed Water Treatment

35

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


Deposit control

• To avoid efficiency losses and reduced heat transfer

• Hardness salts of calcium and magnesium• Alkaline hardness: removed by boiling

• Non-alkaline: difficult to remove

• Silica forms hard silica scales

Boiler Feed Water Treatment

36

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


Internal water treatment

• Chemicals added to boiler to prevent scale

• Different chemicals for different water types

• Conditions:

• Feed water is low in hardness salts

• Low pressure, high TDS content is tolerated

• Small water quantities treated

• Internal treatment alone not recommended


37

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


External water treatment:

• Removal of suspended/dissolved solids and dissolved gases

• Pre-treatment: sedimentation and settling

• First treatment stage: removal of salts

• Processes

a) Ion exchange

b) Demineralization

c) De-aeration

d) Reverse osmoses


38

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


a) Ion-exchange process (softener plant)• Water passes through bed of natural zeolite of

synthetic resin to remove hardness

• Base exchange: calcium (Ca) and magnesium (Mg) replaced with sodium (Na) ions

• Does not reduce TDS, blow down quantity and alkalinity

b) Demineralization• Complete removal of salts

• Cations in raw water replaced with hydrogen ions

External Water Treatment

39

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


c) De-aeration

• Dissolved corrosive gases (O2, CO2) expelled by preheating the feed water

• Two types:

• Mechanical de-aeration: used prior to addition of chemical oxygen scavangers

• Chemical de-aeration: removes trace oxygen


40

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006



Steam

Storage Section

De-aerated Boiler Feed Water

Scrubber Section (Trays)

Boiler Feed Water

VentSpray Nozzles

( National Productivity Council)

Mechanical de-aeration• O2 and CO2 removed by

heating feed water

• Economical treatment process

• Vacuum type can reduce O2 to 0.02 mg/l

• Pressure type can reduce O2 to 0.005 mg/l

41

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006



Chemical de-aeration

• Removal of trace oxygen with scavenger

• Sodium sulphite:

• Reacts with oxygen: sodium sulphate

• Increases TDS: increased blow down

• Hydrazine

• Reacts with oxygen: nitrogen + water

• Does not increase TDS: used in high pressure boilers

42

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


d) Reverse osmosis

• Osmosis

• Solutions of differing concentrations

• Separated by a semi-permeable membrane

• Water moves to the higher concentration

• Reversed osmosis

• Higher concentrated liquid pressurized

• Water moves in reversed direction


43

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


d) Reverse osmosis

External water treatment

More Concentrated

Solution

Fresh Water

Water Flow

Semi Permeable Membrane

Feed Water

Concentrate Flow

Pressure

45

Ther m

al Equipm

ent/B

oil ers

1. Stack temperature control2. Feed water preheating using

economizers3. Combustion air pre-heating4. Incomplete combustion

minimization5. Excess air control6. Avoid radiation and convection

heat loss7. Automatic blow down control8. Reduction of scaling and soot

losses9. Reduction of boiler steam

pressure10. Variable speed control11. Controlling boiler loading12. Proper boiler scheduling13. Boiler replacement

©© UNEP 2006 UNEP 2006

Energy Efficiency OpportunitiesEnergy Efficiency Opportunities

46

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006

1. Stack Temperature Control

• Keep as low as possible

• If >200°C then recover waste heat


2. Feed Water Preheating Economizers

• Potential to recover heat from 200 – 300 oC flue gases leaving a modern 3-pass shell boiler

3. Combustion Air Preheating• If combustion air raised by 20°C = 1% improve

thermal efficiency

47

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006

4. Minimize Incomplete Combustion• Symptoms:

• Smoke, high CO levels in exit flue gas

• Causes: • Air shortage, fuel surplus, poor fuel distribution

• Poor mixing of fuel and air

• Oil-fired boiler: • Improper viscosity, worn tops, cabonization on

dips, deterioration of diffusers or spinner plates

• Coal-fired boiler: non-uniform coal size


48

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


5. Excess Air Control• Excess air required for complete combustion

• Optimum excess air levels varies

• 1% excess air reduction = 0.6% efficiency rise

• Portable or continuous oxygen analyzers

Fuel Kg air req./kg fuel %CO2 in flue gas in practice

Solid Fuels Bagasse Coal (bituminous) Lignite Paddy Husk Wood

3.3 10.7 8.5 4.5 5.7

10-12 10-13 9 -13 14-15 11.13

Liquid Fuels Furnace Oil LSHS

13.8 14.1

9-14 9-14

49

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


7. Automatic Blow Down Control

6. Radiation and Convection Heat Loss Minimization• Fixed heat loss from boiler shell, regardless of

boiler output

• Repairing insulation can reduce loss

• Sense and respond to boiler water conductivity and pH

50

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


9. Reduced Boiler Steam Pressure

8. Scaling and Soot Loss Reduction

• Every 22oC increase in stack temperature = 1% efficiency loss

• 3 mm of soot = 2.5% fuel increase

• Lower steam pressure

= lower saturated steam temperature

= lower flue gas temperature

• Steam generation pressure dictated by process

51

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


11. Control Boiler Loading

10. Variable Speed Control for Fans, Blowers and Pumps• Suited for fans, blowers, pumps

• Should be considered if boiler loads are variable

• Maximum boiler efficiency: 65-85% of rated load

• Significant efficiency loss: < 25% of rated load

52

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006


13. Boiler Replacement

12. Proper Boiler Scheduling• Optimum efficiency: 65-85% of full load

• Few boilers at high loads is more efficient than large number at low loads

Financially attractive if existing boiler is

• Old and inefficient

• Not capable of firing cheaper substitution fuel

• Over or under-sized for present requirements

• Not designed for ideal loading conditions

53

Training Session on Energy Training Session on Energy EquipmentEquipment

Boilers & Thermic Boilers & Thermic Fluid HeatersFluid Heaters

THANK YOUTHANK YOUFOR YOUR ATTENTIONFOR YOUR ATTENTION

©© UNEP GERIAP UNEP GERIAP

Ther m

al Equipm

ent/B

oil ers

54

Ther m

al Equipm

ent/B

oil ers

©© UNEP 2006 UNEP 2006

Disclaimer and ReferencesDisclaimer and References

• This PowerPoint training session was prepared as part of the project “Greenhouse Gas Emission Reduction from Industry in Asia and the Pacific” (GERIAP). While reasonable efforts have been made to ensure that the contents of this publication are factually correct and properly referenced, UNEP does not accept responsibility for the accuracy or completeness of the contents, and shall not be liable for any loss or damage that may be occasioned directly or indirectly through the use of, or reliance on, the contents of this publication. © UNEP, 2006.

• The GERIAP project was funded by the Swedish International Development Cooperation Agency (Sida)

• Full references are included in the textbook chapter that is available on www.energyefficiencyasia.org

100370254 boilers and thermic fluid heaters

Documents

uniform coal

energy efficiency

energy efficiency

boiler boiler

waste heat

waste heat

combustion

fired boiler