119163798 icnd1-practice-questions-9tut

9tut ICND1 Practice Questions (v2.00)

EXAM: 640-822 Formatted Version By: S Qaisar Shah

File Version: 2.0 My Blog : sqaisars.blogspot.com

Interconnecting Cisco Networking Devices – Part 1(640-822)

(9tut.net Latest Questions)

Content:Exam A: LabSimExam B: LabSimExam C: ARP TestletExam D: HotspotExam E: OperationsExam F: SubnettingExam G: Drag & Drop questionsExam H: Wireless Questions

The author of these questions is the owner of 9tut.net/9tut.com

Visit www.9tut.net for ICND1 and ICND2 questions, sims andfeedback. Visit www.9tut.com for CCNA questions, sims andfeedback.

Good luck studying, practicing and on the exam.

Sections1. LabSim2. ARP Testlet3. Hotspot4. Operations5. Subnetting6. Drag & Drop questions7. Wireless Questions

Exam A

QUESTION 1

This topology contains 3 routers and 1 switch. Complete the topology.

Drag the appropriate device icons to the labeled Device.Drag the appropriate connections to the locations labeled Connections.Drag the appropriate IP addresses to the locations labeled IP address.

(Hint: use the given host addresses and Main router information)To remove a device or connection, drag it away from the topology.

Q A1

Use information gathered from the Main router to complete the configuration of any additionalrouters. No passwords are required to access the Main router. The config terminal command has beendisabled for the HQ router. The router does not require any configuration.

Configure each additional router with the following:Configure the interfaces with the correct IP address and enable the interfaces.Set the password to allow console access to consolepwSet the password to allow telnet access to telnetpwSet the password to allow privilege mode access to privpw

Note: Because routes are not being added to the configurations, you will not be able to pingthrough the internetwork.All devices have cable autosensing capabilities disabled.All hosts are PC’s

Click on Exhibit for further information.

Formatted Version By: S Qaisar Shah.

Answer:

Section: LabSim

Explanation/Reference:

For the device at the bottom-right box, we notice that it has 2 interfaces Fa0/2 and Fa0/4; moreover the linkconnects the PC on the right with the device on the bottom-right is a straight-through link -> it is a switch.

The question stated that this topology contains 3 routers and 1 switch -> two other devices are routers

Place them on appropriate locations as following:

(Host D and host E will be automatically added after placing two routers. Click on them to accessneighboring routers)

Specify appropriate connections between these devices:The router on the left is connected with the Main router through FastEthernet interfaces: use acrossover cableThe router on the right is connected with the Main router through Serial interfaces: use a serial cableThe router on the right and the Switch: use a straight-through cableThe router on the left and the computer: use a crossover cable

(To remember which type of cable you should use, follow these tips:To connect two serial interfaces of 2 routers we use serial cableTo specify when we use crossover cable or straight-through cable, we should remember:

Group 1: Router, Host, ServerGroup 2: Hub, SwitchOne device in group 1 + One device in group 2: use straight-through cableTwo devices in the same group: use crossover cable

For example:we use straight-through cable to connect switch to router, switch to host, hub to host, hub to server…and we use crossover cable to connect switch to switch, switch to hub, router to router, host to host… )

Assign appropriate IP addresses for interfaces:

From Main router, use show running-config command:

(Notice that you may see different IP addresses in the real CCNA exam, the ones shown above are justused for demonstration)

From the output we learned that the ip address of Fa0/0 interface of the Main router is 192.168.152.177/28.

This address belongs to a subnetwork which has:

Increment: 16 (/28 = 255.255.255.240 or 1111 1111.1111 1111.1111 1111.1111 0000)Network address: 192.168.152.176 (because 176 = 16 * 11 and 176 < 177)Broadcast address: 192.168.152.191 (because 191 = 176 + 16 – 1)

And we can pick up an ip address from the list that belongs to this subnetwork: 192.168.152.190 andassign it to the Fa0/0 interface the router on the left

Use the same method for interface Serial0/0 with an ip address of 192.168.152.161

Increment: 16Network address: 192.168.152.160 (because 160 = 16 * 10 and 160 < 161)Broadcast address: 192.168.152.175 (because 176 = 160 + 16 – 1)

-> and we choose 192.168.152.174 for Serial0/0 interface of the router on the right

Interface Fa0/1 of the router on the left

IP (of the computer on the left) : 192.168.152.129/28


-> we choose 192.168.152.142 from the list

Interface Fa0/0 of the router on the right

IP (of the computer on the left) : 192.168.152.225/28


-> we choose 192.168.152.238 from the list

Let’s have a look at the picture below to summarize:

Configure two routers on the left and right with these commands:

Router1 = router on the left

Assign appropriate IP addresses to Fa0/0 & Fa0/1 interfaces:

Router1> enableRouter1# configure terminalRouter1(config)# interface fa0/0Router1(config-if)#Router1(config-if)#

ip address 192.168.152.190no shutdown

255.255.255.240

Router1(config-if)#Router1(config-if)#

interface fa0/1ip address 192.168.152.142 255.255.255.240

Router1(config-if)# no shutdown

Set passwords (configure on two routers)

1. Console password:

Router1(config-if)# exitRouter1(config)# line console 0Router1(config-line)# password consolepw

Router1(config-line)# loginRouter1(config-line)# exit

2. Telnet password:

Router1(config)# line vty 0 4Router1(config-line)# password telnetpwRouter1(config-line)# loginRouter1(config-line)# exit

3. Privilege mode password:

Router1(config)# enable password privpw

4. Save the configuration:

Router1(config)# exitRouter1# copy running-config startup-config

Configure IP addresses of Router2 (router on the right)

Router2> enableRouter2# configure terminalRouter2(config)# interface fa0/0Router2(config-if)#Router2(config-if)#

ip address 192.168.152.238no shutdown

255.255.255.240

Router2(config-if)#Router2(config-if)#

interface serial0/0ip address 192.168.152.174 255.255.255.240

Router2(config-if)# no shutdown

1. Console password:

Router2(config-if)# exitRouter2(config)# line console 0Router2(config-line)# password consolepwRouter2(config-line)# loginRouter2(config-line)# exit

2. Telnet password:

Router2(config)# line vty 0 4Router2(config-line)# password telnetpwRouter2(config-line)# loginRouter2(config-line)# exit

3. Privilege mode password:

Router2(config)# enable password privpw

4. Save the configuration:

Router2(config)# exitRouter2# copy running-config startup-config

QUESTION 2

You have been hired by PC Consultants Incorporated to document the layout of the network.Q A2

Complete the network topology shown in the graphic by dragging the labels below with the appropriaterouter types, interface types and IP addresses to the graphic.

Find the information you need by using the router console attached to the Home router.Click on Exhibit for further information.

Answer:

Section: LabSim


First we have to find out the types of these routers to place them in correct positions by using show cdpneighbors command on HOME router:

There are 3 columns we should pay more attention to:

+ Local Intrfce (Local Interface): the interface on the device you are using “show cdp neighbors”command. In this case it is the interface of HOME router

+ Platform: the platform of neighbor device

+ Port ID: the neighbor device’s port or interface which links to the HOME router

From the exhibit, the “Local Interface”, “Platform” and “Port ID” columns, we can identify where these fourrouters should be placed and their corresponding associated ports

Finally, we need to identify the IP addresses of four interfaces on neighboring routers using show running-config command:

Home# show running-config!interface FastEthernet0/0ip address 192.168.47.1 255.255.255.0 duplex autospeed auto

!interface FastEthernet0/1ip address 192.168.238.1 255.255.255.0 duplex autospeed auto

!interface Serial0/0ip address 192.168.235.1 255.255.255.0 duplex auto

!interface Serial0/1

ip address 192.168.39.1 255.255.255.0 duplex auto

And we can easily assign corresponding ip addresses to four neighbor routers, which are on the samenetwork with HOME router’s interfaces>

QUESTION 3Q A3

Central Florida Widgets recently installed a new router in their Apopka office. Complete the networkinstallation by performing the initial router configurations and configuring RIPv2 routing using the routercommand line interface (CLI) on the Apopka router.

Configure the router per the following requirements:Name of the router is ApopkaEnable-secret password is cisco10The password to access user EXEC mode using the console is RouterPassThe password to allow telnet access to the router is scan90

IPv4 addresses must be configured as follows:Ethernet network 209.165.201.0/27 – router has second assignable host address in subnet.Serial network is 192.0.2.128/28 – router has last assignable host address in the subnet.

Interfaces should be enabled.

Routing protocol is RIPv2.

(Notice: In the real exam the name, passwords, IP addresses and the positions of the assignable hostaddresses might be different)

Case Study Title (Case Study):

1) Name the router:Router> enableRouter# config terminalRouter(config)# hostname Apopka

2) Enable-secret password (cisco10):Apopka(config)# enable secret cisco10

3) Set the console password to RouterPass:Apopka(config)# line console 0Apopka(config-line)# password RouterPassApopka(config-line)# loginApopka(config-line)# exit

4) Set the Telnet password to scan90:Apopka(config)# line vty 0 4Apopka(config-line)# password scan90Apopka(config-line)# loginApopka(config-line)# exit

5) Configure Ethernet interface (on the right) of router Apopka:The subnet mask of the Ethernet network 209.165.201.0 is 27. From this subnet mask, we can find out theincrement by converting it into binary form, that is /27 = 1111 1111.1111 1111.1111 1111.1110 0000. Paymore attention to the last bit 1 because it tells us the increment, using the formula:Increment = 2place of the last bit 1 (starts counting from 0,from right to left), in this case increment = 25 =32. Therefore:

Increment: 32Network address: 209.165.201.0Broadcast address: 209.165.201.31 (because 209.165.201.32 is the second subnetwork, so the previousIP – 209.165.201.31 – is the broadcast address of the first subnet).

-> The second assignable host address of this subnetwork is 209.165.201.2/27

Assign the second assignable host address to Fa0/0 interface of Apopka router:Apopka(config)# interface Fa0/0Apopka(config-if)# ip address 209.165.201.2 255.255.255.224Apopka(config-if)# no shutdownApopka(config-if)# exit

6) Configure Serial interface (on the left) of router Apopka:Using the same method to find out the increment of the Serial network:Serial network 192.0.2.128/28:Increment: 16 (/28 = 1111 1111.1111 1111.1111 1111.1111 0000)Network address: 192.0.2.128 (because 8 * 16 = 128 so 192.0.2.128 is also the network address of thissubnet)Broadcast address: 192.0.2.143

-> The last assignable host address in this subnet is 192.0.2.142/28.

Assign the last assignable host address to S0/0/0 interface of Apopka router:Apopka(config)# interface S0/0/0 (or use interface S0/0 if not successful)Apopka(config-if)# ip address 192.0.2.142 255.255.255.240Apopka(config-if)# no shutdownApopka(config-if)# exit

7) Configure RIP v2 routing protocol:Apopka(config)# router ripApopka(config-router)# version 2Apopka(config-router)# network 209.165.201.0Apopka(config-router)# network 192.0.2.128Apopka(config-router)# end

Save the configuration:

Apopka# copy running-config startup-config

Finally, you should use the ping command to verify all are working properly!

A. The command Apopka(config-line)# login was issued to save the user password in the filepassword.txt

B. The command Apopka(config-line)# login was issued to prompt the user for a password whenconnected

C. The last assignable host address on the 192.168.0.128/28 network is 192.168.0.143

D. The command:Apopka(config-router)# network 192.0.2.128is equal to the command:Apopka(config-router)# network 192.0.2.0

Answer: BDSection: LabSim


Visit http://www.9tut.net/icnd1/labsim/ripv2-sim for further explanation.

Exam B

QUESTION 1Q B1

What is the subnet broadcast address of the LAN connected to Router1?Click on Exhibit for further information.

Exhibit:

A. 192.168.136.15

B. 192.168.136.31

C. 192.168.136.63

D. 192.168.136.127

E. 255.255.255.255

Answer: ASection: LabSim


QUESTION 2

What is the bandwidth on the WAN interface of Router1?

Q B2


Exhibit:

A. 16 Kbit/sec

B. 32 Kbit/sec

C. 64 Kbit/sec

D. 128 Kbit/sec

E. 512 Kbit/sec

F. 1544 Kbit/sec

Answer: ESection: LabSim


QUESTION 3Q B3

What interfaces on Router1 have not had any configurations applied? (Choose two)Click on Exhibit for further information.

Exhibit:

A. Ethernet 0

B. FastEthenet 0/0


Exhibit:

A. Ethernet 0

B. FastEthenet 0/0


Exhibit:

A. Ethernet 0

B. FastEthenet 0/0

C. FastEthernet 0/1

D. Serial 0

E. Serial 0/0

F. Serial 0/1

Answer: CFSection: LabSim


QUESTION 4Q B4

Including the address on the Router1 FastEthernet interface, how many hosts can have IP addresses onthe LAN to which Router1 is connected?


Exhibit:

A. 6

B. 14

C. 62

D. 128

Answer: BSection: LabSim


QUESTION 5Q B5

The hosts in the LAN are not able to connect to the Internet.

Which commands will correct this issue?


Exhibit:

A. Router1(conf)# interface fa0/0Router1(conf-if)# no shutdown




Exhibit:





Exhibit:


B. Router1(conf)# interface fa0/1Router1(conf-if)# no shutdown

C. Router1(conf)# interface s0/0Router1(conf-if)# no shutdown

D. Router1(conf)# interface s0/1Router1(conf-if)# no shutdown

E. Router1(conf)# interface s0/0Router1(conf-if)# ip address 10.11.12.13 255.255.255.252

F. Router1(conf)# interface s0/1Routerl(conf-if)# ip address 10.11.12.13 255.255.255.252

Answer: CSection: LabSim


Exam C

QUESTION 1

In order to begin communicating with the server, host F sends out an ARP request.

How will the devices exhibited in the topology respond to this request?

Q C1

A. Switch West _1 will reply with the MAC address of the server.

B. Hosts D and E will respond that the destination is not on the local LAN.

C. Router SFX will forward the ARP request to the ILM router.

D. Switch West _1 will block the request since the server is not on the LAN.

E. The ILM router will respond with the IP address of the WWW server.

F. Router SFX will respond with the MAC address of its Fa0/0 interface.

Answer: FSection: ARP Testlet


Because the server WWW is on another LAN of host F, host F knows that it has to send its packets to thedefault gateway.Therefore, for the first time, it will send out an ARP broadcast message asking for the MAC address ofrouter SFX.Router SFX receives this message and replies with the MAC address of Fa0/0 interface.Later, when host F wants to send packets to WWW server, it will include the IP address of WWW serverand the MAC address of Fa0/0 interface of SFX router in the “destination IP address” and “destinationMAC address” fields, respectively.

QUESTION 2Q C2

The ARP reply has been received by host F, which needs to build the packet.

What information will be placed in the header of the packet that leaves host F if host F is to communicatewith the WWW server? (Choose two)

A. The destination address will be the IP address of interface Fa0/0 of the ILM router.

B. The destination address will be the IP address of the WWW server.

C. The destination address will be the IP address of interface Fa0/0 of router SFX.

D. The source address will be the IP address of host F.

E. The source address will be the IP address of interface Fa0/0 of router SFX.

F. The destination address will be the IP address of interface Fa0/0 of router SFX.

Answer: BDSection: ARP Testlet


After receiving ARP reply from SFX router, host F will place these fields in the header of the packets:

Source addresses: the IP address of host F and the MAC address of host FDestination addresses: the IP address of WWW server and the MAC address of SFX router

QUESTION 3Q C3

The frame has been received by the ILM router and is to be delivered on the local LAN.

Which two statements describe the addressing of the Ethernet frame that has been created by the ILMrouter? (Choose two)

A. The destination address will the be the MAC address of the switch A port attached to the Fa0/0interface of the ILM router .

B. The destination address will be the MAC address of the WWW server.

C. The destination address will be the MAC address of the A switch port attached to the WWW server.

D. The source address will be the MAC address of host F.

E. The source address will be the MAC address of interface Fa0/0 of the ILM router.

Answer: BESection: ARP Testlet


QUESTION 4Q C4

Host F is displaying two World Wide Web documents from the WWW server in two browser windows at thesame time.

How did the data find its way to the correct browser windows?

A. The IP source addresses of the packets will be used to direct the data to the correct browser window.

B. The browsers track the data by the URL.

C. TCP port numbers are used to direct the data to the correct application window.

D. The OSI application layer tracks the conversations and directs them to the correct browser.

Answer: CSection: ARP Testlet


TCP and UDP protocol port numbers are designed to distinguish multiple applications running on a singledevice from one another.In the TCP and UDP header, there are “Source Port” and “Destination Port” fields which are used toindicate the message sending process and receiving process identities defined.The combination of the IP address and the port number is called “socket”.

Exam D

QUESTION 1Q D1

On which router should a default route be configured?

A. on the ISP router

B. on R1

C. on R2

D. on R3

Answer: BSection: Hotspot


QUESTION 2Q D2

With all links operational and all routers converged, which of the following describes the messagingbetween routers?

A. Hellos are sent every five seconds.

B. Multicasts are sent every 60 seconds.

C. Broadcasts are sent every 30 seconds.

D. No messaging unless the topology changes.

Answer: CSection: Hotspot


QUESTION 3Q D3

Which of the following describes the route update process if the interface from R4 connected to LAN 4goes down?

A. No updates occur

B. R4 tells both R1 and R3 the network not accessible. Both R3 and R1 update R2.

C. R4 tells only R1 the network is not accessible. R1 updates R2 and R2 updates R3.

D. R4 tells only R3 the network is not accessible. R3 updates R2 and R2 updates R1.

Answer: BSection: Hotspot


QUESTION 4Q D4

Why would RIP be used rather than static routes on R1, R2, R3, and R4?

A. RIP creates more accurate than static routes.

B. RIP uses less network resources than do static routes.

C. RIP is supported by more different vendors equipment than static routes.

D. RIP requires less configuration to automatically adjust when links go down than static routes.

Answer: DSection: Hotspot


QUESTION 5Q D5

On which router should a static route be configured?

A. on the ISP router

B. on R1

C. on R2

D. on R3

E. on R4

Answer: ASection: Hotspot


Usually, a static route would be needed on the router which is connected to the ISP router to route to theInternet.The ISP router only needs a static route to reach the LANs network.

Exam E

QUESTION 1Q E1

The junior network support staff provided the diagram as a recommended configuration for the first phaseof a four-phase network expansion project.The entire network expansion will have over 1000 users on 14 network segments and has been allocatedthis IP address space:

192.168.1.1 through 192.168.5.255192.168.100.1 through 198.168.100.255

What are three problems with this design? (Choose three)

A. The AREA 1 IP address space is inadequate for the number of users.

B. The AREA 3 IP address space is inadequate for the number of users.

C. AREA 2 could use a mask of /25 to conserve IP address space.

D. The network address space that is provided requires a single network-wide mask.

E. The router-to-router connection is wasting address space.

F. The broadcast domain in AREA 1 is too large for IP to function.

Answer: ACESection: Operations


QUESTION 2

A technician is testing connection problems in the internetwork.

What is the problem indicated by the output from HostA?

Q E2

A. The routing on Router2 is not functioning properly.

B. An access list is applied to an interface of Router3.

C. The Fa0/24 interface of Switch1 is down.

D. The gateway address of HostA is incorrect or not configured.

Answer: DSection: Operations


When trying to ping the IP 192.168.3.254, you received the replies from that IP.It means that you can reach the Fa0/0 interface of Router1.But notice that the IP of host A (192.168.3.1/24) and the IP of the Fa0/0 interface of Router 1(192.168.3.254/24) are on the same network.So you don’t need a gateway address configured on HostA.Therefore you can’t conclude the gateway address of HostA was configured correctly.

Lately, you tried to use the tracert command to reach another network (192.168.4.7).In this case, a gateway address was required for reaching the network of hostB.But the result told that “Destination host unreachable” – means that Host A can not find a route to Host B-> The gateway address of Host A was incorrect (something other than 192.168.3.254) or not configured isa possibility.

A and B are incorrect because if there is a mis-configuration on Router 2 or Router 3 (while Router 1 is

configurated correctly), you will see at least one successful line when using tracert command likes the boldline below:

PC> tracert 192.168.4.7Tracing route to 192.168.4.7 over a maximum of 30 hops:1 62 ms 62 ms 46 ms 192.168.3.2542 * * * Request timed out.

C is incorrect because we can ping Router 1 -> port Fa0/24 on Switch 1 was turned on and runningcorrectly.

QUESTION 3

The internetwork is using subnets of the address 192.168.1.0 with a subset mask of 255.255.255.224.The routing protocol in use is RIP version 1.

Which address could be assigned to the FastEthernet interface on RouterA?

Q E3

A. 192.168.1.31

B. 192.168.1.64

C. 192.168.1.127

D. 192.168.1.190

E. 192.168.1.192



255.255.255.224 = 1111 1111.1111 1111.1111 1111.1110 0000 (binary form)

Increment: 32

First subnetwork: 192.168.1.0 -> 192.168.1.31 (A is incorrect because 192.168.1.31 is a broadcastaddress)Second subnetwork: 192.168.1.32 -> 192.168.1.63Third subnetwork: 192.168.1.64 -> 192.168.1.95 (B is incorrect because 192.168.1.64 is a networkaddress)Fourth subnetwork: 192.168.1.96 -> 192.168.1.127 (C is incorrect because 192.168.1.127 is a

broadcast address)Fifth subnetwork: 192.168.1.128 -> 192.168.1.159Sixth subnetwork: 192.168.1.160 -> 192.168.1.191 (D is correct because 192.168.1.190 is the lastassignable host address of this subnetwork)Seventh subnetwork: 192.168.1.192 -> 192.168.1.224 (E is incorrect because 192.168.1.192 is anetwork address)

QUESTION 4

For security reasons, information about RTA, including platform and IP addresses, should not beaccessible from the Internet.This information should, however, be accessible to devices on the internal networks of RTA.

Which command or series of commands will accomplish these objectives?

Q E4

A. RTA(config)# no cdp run

B. RTA(config)# no cdp enable

C. RTA(config)# interface s0/0RTA(config-if)# no cdp run

D. RTA(config)# interface s0/0RTA(config-if)# no cdp enable



QUESTION 5Q E5

What three things will CORE router do with the data that is received from PC1? (Choose three)

A. The data frames will be forwarded out interface FastEthernet0/1 of CORE router.

B. The data frames will be forwarded out interface FastEthernet1/0 of CORE router.

C. CORE router will replace the destination IP address of the packets with the IP address of PC2.

D. CORE router will place the MAC address of PC2 in the destination MAC address of the frames.

E. CORE router will put the IP address of the forwarding FastEthernet interface in the place of the sourceIP address in the packets.

F. CORE router will put the MAC address of the forwarding FastEthernet interface in the place of thesource MAC address.

Answer: BDFSection: Operations


Exam F

QUESTION 1

The goal of this network design is to provide the most efficient use of IP address space in a networkexpansion.Each circle defines a network segment and the number of users required on that segment.An IP subnetwork number and default gateway address are shown for each segment.

What are three problems with the network design as shown? (Choose three)

Q F1

A. Interface fa0/3 has an IP address that overlaps with network 10.1.3.0/30.

B. Interface fa0/1 has an invalid IP address for the subnet on which it resides.

C. Interface fa0/2 has an invalid IP address for the subnet on which it resides.

D. Network 10.1.2.0/25 requires more user address space.

E. Network 10.1.3.128/25 requires more user address space.

F. The IP subnet 10.1.1.0/30 is invalid for a segment with a single server.

Answer: ABDSection: Subnetting


QUESTION 2

If an ethernet port on a router was assigned an IP address of 172.16.112.1/20, what is the maximumnumber of hosts allowed on this subnet?

Q F2

A. 1024

B. 2046

C. 4094

D. 4096

E. 8190

Answer: CSection: Subnetting


QUESTION 3

The internetwork is using subnets of the address 192.168.1.0 with a subnet mask of 255.255.255.224.The routing protocol in use is RIP version 2.

Which address could be assigned to the FastEthernet interface on RouterA?

Q F3

A. 192.168.1.31

B. 192.168.1.64

C. 192.168.1.127

D. 192.168.1.190

E. 192.168.1.192

Answer: DSection: Subnetting


QUESTION 4

HostA cannot ping HostB.

Assuming routing is properly configured, what could be the cause of this problem?

Q F4

A. HostA is not on the same subnet as its default gateway.

B. The address of SwitchA is a subnet address.

C. The Fa0/0 interface on RouterA is on a subnet that can’t be used.

D. The serial interfaces of the routers are not on the same subnet.

E. The Fa0/0 interface on RouterB is using a broadcast address.

Answer: DSection: Subnetting


Exam G

QUESTION 1Q G1

Answer:

Section: Drag & Drop questions


QUESTION 2Q G2

Answer:



QUESTION 3Q G3

Answer:



QUESTION 4

Answer:



Q G4

First please notice that by saying “replace” we often mean changes to NVRAM and TFTP while saying“merge” or “add” we mean changes to RAM.Next we should review the syntax of “copy” command:Syntax: copy <source> <base config filename> <destination> <destination filename.txt>

1. By default, the flash memory in a router is used to store the Cisco IOS image so the requirement “replace the IOS image” means that moving file somewhere to the flash memory.In the left columns we only have one choice which has the flash as the destination ->copy tftp flash.

2. Same explanation as above, when saying “backup the current IOS image” the flash takes the role asthe source ->copy flash tftp.

And “backup” means we should copy it to somewhere like tftp server, CDROM…

3. The running-config is stored in the RAM so “make a backup copy of configuration in RAM” meanscopy running configuration from RAM to backup server (tftp) -> copy running-config tftp

4. “copy running-config startup-config” is a very common command so no more explanation needed.

5. After solving 4 boxes above, we only have two choices left: “copy tftp running-config” & “copy flashrunning-config”.The bottom-right box says “merge a backup configuration” so it should be the tftp server and thecommand here is copy tftp running-config.

Q#5 : As a CCNA candidate, you should master the functions of various commands. Look at thefollowing items, some commands are listed on the left. The related roles are listed on the right in awrong sequence. Please match them together. (Not all options are used)

Answer:

1) Router#copy tftp flash: replace the IOS image2) Router#copy flash tftp: backup the current IOS image3) Router#copy running-config tftp: make a backup copy of configuration in RAM4) Router#copy running-config startup-config: make the configuration in RAM the configuration therouter will use on startup5) Router#copy tftp running-config: merge a backup configuration with the configuration in RAM

Explanation

First please notice that by saying “replace” we often mean changes to NVRAM and TFTP while saying“merge” or “add” we mean changes to RAM. Next we should review the syntax of “copy” command:

Syntax: copy <source> <base config filename> <destination> <destination filename.txt>

1) By default, the flash memory in a router is used to store the Cisco IOS image so the requirement“replace the IOS image” means that moving file somewhere to the flash memory. In the left columns weonly have one choice which has the flash as the destination ->copy tftp flash.

2) Same explanation as above, when saying “backup the current IOS image” the flash takes the role asthe source ->copy flash tftp. And “backup” means we should copy it to somewhere like tftp server,CDROM…

3) The running-config is stored in the RAM so “make a backup copy of configuration in RAM” means copyrunning configuration from RAM so backup server (tftp) -> copy running-config tftp

4) “copy running-config startup-config” is a very common command so no more explanation needed.

5) After solving 4 boxes above, we only have two choices left: “copy tftp running-config” & “copy flashrunning-config”. The bottom-right box says “merge a backup configuration” so it should be the tftpserver and the command here is copy tftp running-config.

Exam H

QUESTION 1Q H1

Which wireless LAN design ensures that a mobile wireless user will not lose connectivity when movingfrom one access point to another on the WLAN?

A. Utilizing MAC address filtering to allow the client MAC address to authenticate with the surrounding APs

B. Using adapters and access points manufactured by the same company

C. Overlapping the wireless cell coverage by at least 10%

D. Configuring all access points to use the same channel

Answer: CSection: Wireless Questions


By using more than one Access Point (AP) we can create overlapping cells to allow roaming in a largerarea.But we have to ensure that two APs must have at least 10% coverage overlap and they use non-overlapping channels.

QUESTION 2

You need to troubleshoot an interference issue with the wireless LAN.

Which two devices can interfere with the operation of this network because they operate on similarfrequencies? (Choose two)

Q H2

A. Microwave oven

B. AM radio

C. Toaster

D. Copier

E. Cordless phone

F. IP phone

G. Ipod Formatted Version By: S Qaisar Shah.

Answer: AESection: Wireless Questions


Microwave oven and cordless phone radiate energy in the 2.4 GHz unlicensed band so they can interfere

with some WLAN standards.As the result of that, you can’t hear clearly on the phone or can’t surf web.

QUESTION 3

Which of the following data network would you implement if you wanted a wireless network that had arelatively high data rate, but was limited to very short distances?

Q H3

A. Broadband personal comm. Service (PCS)

B. Broadband circuit

C. Infrared

D. Spread spectrum

E. Cable



Infrared typically requires a line-of-sight (your TV remote control, for example) which means that it is limitedto very short distances.I am not sure if it is considered “relative high data rate” but infrared can transfer up to 4Mpbs.

QUESTION 4

You need to add a wireless access point to a new office.

Which additional configuration step is necessary in order to connect to an access point that has SSIDbroadcasting disabled?

Q H4

A. Configure open authentication on the AP and the client

B. Set the SSID value in the client software to public

C. Set the SSID value on the client to the SSID configured on the AP

D. Configure MAC address filtering to permit the client to connect to the AP



Service Set Identifier (SSID) is the term to identify a WLAN. In most cases SSID is broadcast by the AP,the user only needs to select that SSID and provides a correct password to access it.But in some cases for security reason, the SSID can be disabled.Users can only access to that network if they type both SSID and password correctly.

QUESTION 5

You need to secure a new access point on the a wireless network.Q H5

Which two practices help secure the configuration utilities on wireless access points from unauthorizedaccess? (Choose two)

A. Changing the default SSID value

B. Configuring traffic filtering

C. Changing the mixed mode setting to single mode

D. Configuring a new administrator password

E. Assigning a private IP address to the AP

Answer: ADSection: Wireless Questions


To improve security, you should change the default SSID value on your AP.For example, Linksys routers (which are produced by Cisco) typically have an SSID of “linksys” -> A iscorrect.

In an AP we can configure traffic filtering but it is mainly used for filtering which services clients can use, IPranges, ports, websites, time access…It has no effect on securing your AP -> B is not correct.

“Mixed mode” here means we can configure AP to allow clients to use different standard like 802.11b, g orn.But setting it to single mode doesn’t have any security protection on it -> C is not correct.

We should also change the administrator password because everyone can access to the admin page of anAP by open a web browser and type the IP address of that AP (for example: http://192.168.1.1).Typically, Linksys Wireless routers have a default username/password of “admin/admin” or “admin/[blank]”which are easily guessed or found out -> D is correct.

We can access the AP by using a private IP address (in the same private network of the AP – 192.168.1.1,for example) -> E is not correct.

QUESTION 6

You need to determine the proper security settings on a new WLAN-capable office.

Which encryption type would WPA2 use in this office?

Q H6

A. PSK

B. AES-CCMP

C. PPK via IV

D. TKIP/MIC

E. None of the other alternatives apply

Answer: BSection: Wireless Questions


Advanced Encryption Standard (AES) is the cipher system used by RSN.It is the equivalent of the RC4 algorithm used by WPA.However the encryption mechanism is much more complex and does not suffer from the problemsassociated with WEP. AES is a block cipher, operating on blocks of data 128bits long.

CCMP is the security protocol used by AES.It is the equivalent of TKIP in WPA.CCMP computes a Message Integrity Check (MIC) using the well known, and proven, Cipher BlockChaining Message Authentication Code (CBC-MAC) method.Changing even one bit in a message produces a totally different result.

The AES-CCMP encryption algorithm used in the 802.11i (WPA2) security protocol.It uses the AES block cipher, but restricts the key length to 128 bits.AES-CCMP incorporates two sophisticated cryptographic techniques (counter mode and CBC-MAC) andadapts them to Ethernet frames to provide a robust security protocol between the mobile client and theaccess point.

QUESTION 7

What is one reason why WPA encryption is preferred over WEP in this network?Q H7

A. The WPA key values remain the same until the client configuration is changed.

B. The values of WPA keys can change dynamically while the system is used.

C. The access point and the client are manually configured with different WPA key values.

D. A WPA key is longer and requires more special characters than the WEP key.




Wireless Encryption Protocol (WEP) uses RC4 encryption and a static 64-bit key so it can be easily brokenas only 40-bits are encrypted and 24 bits are clear-text IV(Initialization Vector).It was later upgraded to 128-bit, but the IV was still clear text meaning it took slightly longer (minutes) tobreak-in.

WPA was introduced in 2003 as a replacement for WEP.WPA uses Temporal Key Integrity Protocol (TKIP) to automatically change the keys.TKIP still uses RC4; it just improves how it’s done.

QUESTION 8

In an effort to increase security within the wireless network, WPA is being utilized.Q H8

Which two statements shown below best describe the wireless security standard that is defined by WPA? (Choose two)

A. It requires use of an open authentication method

B. It specifies use of a static encryption key that must be changed frequently to enhance security

C. It includes authentication by PSK

D. It specifies the use of dynamic encryption keys that change each time a client establishes a connection

E. It requires that all access points and wireless devices use the same encryption key

F. WPA works only with Cisco access points

Answer: CD Formatted Version By: S Qaisar Shah.Section: Wireless Questions


QUESTION 9

You need to configure a new wireless access point for your network.

What are three basic parameters to configure an AP? (Choose three)

Q H9

A. Authentication method

B. RTS/CTS

C. RF channel

D. SSID

Answer: ACDSection: Wireless Questions


QUESTION 10

You have finished physically installing an access point on the ceiling at a newly opened office.Q H10

At a minimum, which parameter must you configure on the access point in order to allow wireless clients tooperate on it?

A. SSID

B. AES

C. TKIP

D. PSK


Answer: ASection: Wireless Questions


QUESTION 11Q H11

What two facts can be determined from the diagram of the WLAN shown above? (Choose two)

A. Access points in each cell must be configured to use channel 1

B. The network diagram represents an extended service set (ESS)

C. The two APs should be configured to operate on different channels

D. The area of overlap of the two cells represents a basic service set (BSS)

E. The area of overlap must be less than 10% of the area to ensure connectivity

F. There are too many hosts on this WLAN

Answer: BCSection: Wireless Questions


QUESTION 12Q H12

A single 802.11g access point has been configured and installed in the center of a square shaped office.A few wireless users are experiencing slow performance and drops while most users are operating at peakefficiency.

From the list below, what are three likely causes of this problem? (Choose three)

A. Null SSID

B. Mismatched TKIP encryption

C. Cordless phones

D. Antenna type or direction

E. Mismatched SSID

F. Metal file cabinets

Answer: CDFSection: Wireless Questions


802.11g operates in 2.4 GHz ISM band. Some popular devices and technologies can interfere 802.11gsignal:

Newer cordless phonesBluetoothMicrowavesMetal surface (can cause interference)Antenna (can reduce wireless signal)

QUESTION 13

Three access points have been installed and configured to cover a small remote office.

What term defines the wireless topology?

Q H13

A. SSID

B. BSS

C. ESS

D. IBSS

E. ASS



QUESTION 14

Two workers have established wireless communication directly between their wireless laptops.

What type of wireless topology has been created by these employees?

Q H14

A. ESS

B. IBSS

C. SSID

D. BSS



Independent Basic Service Set – IBSS (ad hoc mode) does not use an AP.It allows two devices to communicate directly.

Basic Service Set (BSS) is a single wireless LAN created with an AP and all devices that associate withthat AP.

Extended Service Set (ESS) consists of multiple APs, allowing roaming in a larger coverage area.

QUESTION 15

802.1b is being utilized in the wireless network.

Which spread spectrum technology does the 802.1b standard define for operation in this network?

Q H15

A. FHSS

B. IR

C. DSSS and FHSS

D. DSSS

E. IR, FHSS and DSSS

Answer: DSection: Wireless Questions


Frequency Hopping Spread Spectrum (FHSS) uses all frequencies in the band, hopping to different ones.By using slightly different frequencies for consecutive transmissions, a device can hopefully avoidinterference from other devices that use the same unlicensed band, succeeding at sending data at somefrequencies.

Direct Sequence Spread Spectrum (DSSS) followed as the next general class of encoding type for WLANs.Designed for use in the 2.4 GHz unlicensed band, DSSS uses one of several separate channels orfrequencies.

The original 802.11 WLAN standards used FHSS, but the current standards (802.11a, 802.11b, and802.11g) do not.802.1b uses DSSS while 802.1a & 802.1g use Orthogonal Frequency Division Multiplexing (OFDM).

(Reference: ICND1 Official Exam Certification Guide)

QUESTION 16

Which IEEE standard is used to define Wi-Fi?Q H16

A. IEEE 802.3

B. IEEE 802.5

C. IEEE 802.11h

D. IEEE 802.11c

E. IEEE 802.11

Answer: ESection: Wireless Questions


QUESTION 17

An office is using an IEEE 802.11b wireless LAN.

What is the maximum data rate specified for this WLAN?

Q H17

A. 11 mbps

B. 100 mbps

C. 54 mbps

D. 10 mbps

E. 1000 mbpsFormatted Version By: S Qaisar Shah.

F. 16 mbps

Answer: ASection: Wireless Questions


The maximum data rate for popular WLAN standards are listed below:IEEE 802.11a: 54 Mbps in the 5.7 GHz ISM bandIEEE 802.11b: 11 Mbps in the 2.4 GHz ISM bandIEEE 802.11g: 54 Mbps in the 2.4 GHz ISM band

119163798 icnd1-practice-questions-9tut

Technology

hq router

main router information

network address

broadcast address

correct ip address

ip address of fa00 interface

serial cable

serial interfaces