WARNING:Cancer and Reproductive HarmFor more information refer to:www.P65Warnings.ca.gov▲! 8 800-488-3407 Rotary Cutters 195&

3:1 Right AngleGearReducer

ITEM 13-1564$302.85• Brand new. OMNI-GEAR LR-200 Series Model 251075 right angle gearbox. One piece cast iron gear case and bearing caps. Roller bearings. Spiral bevel gears.Hollow output with full length keyway.SPECIFICATIONS• Ratio 3:1• Input power 32 HP continuous• Input speed 1800 RPM max.• Input shaft 1˝ dia. x 13/4˝ with 1/4˝ crosshole and snap ring groove• Output shaft hollow 1˝ diam. x 6˝ w/ 1/4˝ keyway• Mount four 3/8-16 tapped holes, 41/4˝ sq.• Size 61/2˝ x 61/4˝ x 41/8˝• Shpg. 23 lbs.

Rotary Cutter GearboxesBrand new, OMNI GEAR Rotary right angle rotary cutter gearbox. Horizontal input and vertical output downward.

Bevel gears. Large deep groove ball bearings to support output. Cast iron housing.

RC 30 Series

$129.95 each

SPECIFICATIONS FOR ALL• CCW input gives CW output• Input RPM 540/1000• Input HP 24-40• Max torque 2800-4667 in.lbs.• Output shaft 19/16˝ dia. 12 tooth tapered spline with threaded end 41/2˝ total length• Blade hub 2.95˝ dia. x 2.02˝ stepped down to 2.5˝ dia. x 0.27˝ then tapers down to 2.183˝ dia. over 0.315˝• Mount 4 holes on 6.8˝ dia. B.C.• Pilot 51/4˝ dia. • Size 101/4˝ x 7˝ x 7˝• Shpg. 54 lbs.

ITEM 13-1526SPECIFICATIONS• Model 250001• Input shaft 13/8˝ dia. x 3˝ long with 1/2˝ dia. pinhole• Gear ratio 1:1.47 increaser• Output RPM 790/1460

ITEM 13-1527SPECIFICATIONS• Model 250179• Input shaft 13/8˝ dia. x 37/8˝ long 6T spline with 5/16˝ dia. pinhole

ITEM 13-1528SPECIFICATIONS• Model 250045• Input shaft 13/8˝ dia. x 3˝ long with 1/2˝ dia. pinhole• Gear ratio 1:1.93 increaser• Output RPM 1042/1930

RC71 Series

$284.70 each

SPECIFICATIONS FOR ALL• Input RPM 540/1000• Input HP 35-83• Max torque 4083-9683 in.lbs.• Input shaft 13/8˝ dia. x 37/8˝ long 6T spline with 5/16˝ dia. pinhole• Output shaft 2˝ dia., 15 tooth tapered spline with threaded end 45/8˝ total length• Blade hub 3.94˝ dia. x 2.275˝ stepped down to 2.5˝ dia. x 0.45˝ then tapers down to 2.175˝ dia. over 0.25˝• Mount 4 holes on 8˝ dia. B.C.• Pilot 55/8˝ dia. • Size 123/8˝ x 93/4˝ x 93/4˝• Shpg. 89 lbs.

ITEM 13-1533SPECIFICATIONS• Model 250598 • Gear ratio 1:1.21 increaser• CW input gives CW output • Output RPM 650/1200 RPM

ITEM 13-1534SPECIFICATIONS• Model 250492 • Gear ratio 1:1.46 increaser• CW input gives CCW output • Output RPM 790/1460 RPM

RC51 Series

$191.45 each

SPECIFICATIONS FOR ALL• CCW input gives CW output• Input RPM 540/1000• Gear ratio 1:1.93 increaser• Output RPM 1040/1930• Input HP 24-40• Max torque 2800-4667 in.lbs.• Output shaft 2˝ dia., 15 tooth tapered spline with threaded end 45/8˝ total length• Blade hub 3.94˝ dia. x 2.275˝ stepped down to 2.5˝ dia. x 0.45˝ then tapers down to 2.175˝ dia. over 0.25˝• Mount 4 holes on 6.8˝ dia. B.C.• Pilot 51/4˝ dia. • Size 101/4˝ x 7˝ x 7˝• Shpg. 59 lbs.

ITEM 13-1529SPECIFICATIONS• Model 250746• Input shaft 13/8˝ dia. x 37/8˝ long 6T spline with 5/16˝ dia. pinhole

ITEM 13-1530SPECIFICATIONS• Model 250618• Input shaft 13/8˝ dia. x 3˝ long with 1/2˝ dia. pinhole

ITEM 13-1531SPECIFICATIONS• Model 251026• Input shaft 13/8˝ dia. x 3˝ long with 1/2˝ dia. pinhole• Blade hub 3.94˝ dia. x 1.75˝ stepped down to 2.5˝ dia. x 1.12˝ then tapers down to 2.175˝ dia. over 0.25˝

Right AngleGear DriveITEM 13-1525$200.50• Brand new, OMNI GEAR Model PHD26HD vertical, right angle gearbox. Originally manufactured for PTO driven post hole digger systems. Tapered roller bearings. Spring loaded triple lip seals. Clockwise input rotation gives clockwise output rotation. Cast iron housing. Designed to free hang from a supporting structure or boom that is connected to it with a 7/8˝ dia. pin at the top of the gearbox housing. Four 3/8˝-16 tapped holes on 33/8˝ dia. B.C. to mount input shaft shield and four 3/8˝-16 tapped holes on 41/8˝ dia. B.C. to mount output shaft shield.SPECIFICATIONS• Gear ratio 2.92:1 • HP input max. 44 HP• RPM 540 input max. • Torque 5133 lb.-in. max.• 38 oz. oil capacity• Inner width of mounting ears 41/4˝• Throat depth of pin 13/16˝• Input shaft 11/4˝ dia. x 2˝ smooth with 5/16˝ dia. pin hole• Output shaft 2˝ x 43/8˝ smooth shaft with two 1/2˝ dia. pin holes 23/4˝ and 33/4˝ bearing to center hole• Size 91/2˝ x 81/4˝ x 75/8˝ • Shpg. 51 lbs.

1:1.46 SpeedIncreaser

ITEM 13-1532$275.35• Brand new, OMNI GEAR 250372 Model RC-61 right angle rotary cutter gearbox. Horizontal input and vertical output downward. Bevel gears. Large deep groove ball bearings to support output. Four 5/16˝-18 tapped holes on 41/8˝ dia. B.C. CCW input gives CW output.SPECIFICATIONS• Gear ratio 1:1.46 increaser• Input RPM 540/1000• Output RPM 790/1460• Input HP 35-72• Max torque 4083-8400 in.lbs.• Input shaft 13/8˝ dia. x 37/8˝ long 6T spline with 5/16˝ dia. pinhole• Output shaft 2˝ dia. 15 tooth tapered spline with threaded end. 45/8˝ total length• Blade hub 3.94˝ dia. x 2.275˝ stepped down to 2.5˝ dia. x 0.45˝ then tapers down to 2.175˝ dia. over 0.25˝• Mount 4 holes on 8˝ dia. B.C.• Pilot 55/8˝ dia.• Size 123/8˝ x 93/4˝ x 93/4˝• Shpg. 84 lbs.

Ordering Information& Shipping Rates

on pages 104 - 105Order Blank on page 106

2 Just Arrived! www.surpluscenter.com

Forklift Seat

ITEM 1-5445$279.95• Brand new, Black Talon 395000BK forklift seat. Universal industrial Features include adjustable seat slide and seat back angle adjustments, retractable seat belts, opera-tor presence switch and document pouch. Ideal for forklifts, lift trucks, commercial turf, construction equipment, ground service equipment, skid steers, specialty vehicles and utility tractors/vehicles.SPECIFICATIONS • Color Black Mounting Patterns Width Center 9.06˝, 11.02˝, 12.60, 12.99˝, 13.39˝ Depth Centers 13˝

• Slide Adjustment Range 6.3˝ 9 positions

• Seat Back Adjustment Range 60 Degrees

• Size 21.5˝ x 23˝ x 23• Actual Weight 50 lbs.• Shpg. 78 lbs. (oversize)

4.80x4.0-8˝ Wheel and Tire AssemblyITEM 1-5443 $39.95• NEW, 153/4˝ x 41/2˝ Pneumatic tire mounted on steel rim. Ideal replacement log split-ter and small trailer wheel for high speed trailer use. Grease seal and roller bearings in the hub. Dust cover NOT included. SPECIFICATIONS • Size 4.80x4.0-8• Outside Diameter 151/4˝

dia.• Cross Section 23/4˝ Wide• Tread Saw Tooth• Tread Width 33/4˝• Bore 1˝

• Bore Thru-Length 33/4˝• Hub Type Center• Bearing Roller Bearing• Tire Tubeless• Load Rating 390 lbs.• Pressure 30 PSI max.• Ply Rating 4• Shpg. 13 lbs.

4.5˝ x 30˝ x 2˝ DA Hydraulic Cylinder

ITEM 9-12457 $199.95• New. PRINCE welded, double-acting clevis cylinder with thread-in gland cap. Ideal for use in agricultural and industrial equipment. Royalplate Plus cylinder rod for corrosion resistance. Pins not included.SPECIFICATIONS • Type Double-Acting• Bore x Stroke 4.5˝ x 30˝• Pressure 3000 PSI max.• Rod Dia. 2˝• Ports SAE 8• Retracted Length 401/4˝• Clevis Ends

• Rod Outside Width 27/8˝• Rod Inside Width 11/8˝• Rod Throat Depth 11/2˝• Base Outside Width 31/16˝• Base Inside Width 11/16˝• Base Throat Depth 13/4˝• Pin Holes 1• Shpg. 83 lbs.

27.1 HP Kubota Diesel Engine

ITEM 28-1904-D $2895.95• New, KUBOTA diesel engine. Reliable, quiet and durable power 3 cylinder diesel engine for a variety of industrial applica-tions. Engine has many built-in design features to provide clean emissions, fuel economy and noise reduction. Additional features include cast iron block and cylin-der head, constant speed governor, glow plugs and 12 volt alternator. No starter or engine shut-off solenoid.SPECIFICATIONS • Model D1703-M-BG-ET01• Power 27.1 HP (20.2 kW)

@ 1800 RPM• Displacement 1.7 Liters• Alternator 12 VDC • Bell Housing None• Flywheel: Size 133/16˝

diameter Pilot 314mm˝ Bolt Holes 8 Hole Spacing 295mm bolt circle • Size 22˝ x 19˝ x 261/2˝• Shpg. 395 lbs.

12 VDC 1350 lb. Linear Actuator

ITEM 5-116267 $169.95• New, LINAK model 30KX00-0020020N heavy actuator. Externally adjustable SPDT microswitches to set travel endpoints.SPECIFICATIONS • Stroke 200 mm (7.87˝)• Voltage 12 DC• Push/Pull Rating Push 1350 lbs./Pull 675 lbs. max• Extension Speed No Load 8.7 in/sec Max Load 5.5 in/sec

• Amps: No Load 2.5 Full Load 9.4• Duty 10% (2 minutes

on/18 minutes off)• Enclosure IPX0• Pin Holes 1/2˝• Retracted Length 155/8˝• Size 161/2˝ x 41/4˝ x 31/2• Shpg. 9 lbs.

5˝ x 2˝ Swivel CasterITEM 1-5426 $6.95• New, 5˝ x 2˝ swivel plate caster.SPECIFICATIONS • Wheel Diameter 5˝ dia.• Wheel Width 2˝ wide• Mounting Height 61/2˝• Top Plate 41/2˝ x 4˝ • Load Rating 1000 lbs.

• Mount 4 holes 3˝ x 35/8˝ slotted to 25/8˝ x 3˝

• Bolt Holes 7/16˝ dia.• Wheel Tread Material

Phenolic• Caster Wheel Bearing

Roller

SPECIFICATIONS FOR ALL• Pump type gear • Speed 3600 RPM max. • Rqd. filtration 25 micron• Rotation CW • Unloading pressure 650 PSI • Shaft 1/2˝ dia. x 11/2˝ keyed• Press. 3000 PSI max. • Mount 4 bolt USA 4F17 • Cast Iron Front and Aluminum Body

DELI-BUCHER Hydraulics Two Stage Hydraulic Pumps•Brand new DELI-BUCHER Hydraulics, two stage HI/LO pressure hydraulic gear pumps.Ideal for applications such as log splitters,

presses and other equipment where rapid movement of the cylinder at low pressure is required prior to automatically switching to the high pressure mode to meet load requirements

Flow (GPM) Engine Power ITEM LO Stage HI Stage Required Inlet Outlet Size Shpg. Price 9-12373-11 11 3.2 5 HP 1˝ Hosebarb 1/2˝ NPT 5˝ x 51/8˝ x 33/8˝ 10 lbs. $119.95 9-12373-13 13 3.2 6.5 HP 1˝ Hosebarb 1/2˝ NPT 53/8˝ x 51/8˝ x 33/8˝ 11 lbs. $129.95 9-12373-16 16 3.5 8 HP 1˝ Hosebarb 1/2˝ NPT 53/4˝ x 51/8˝ x 33/8˝ 12 lbs. $139.95

Hydraulic Pilot Control ValveITEM 9-12379 $59.95• New WOLVERINE by PRINCE model WH-PC-HS1 lever operated pilot valve. Use for remote operation of pilot-operated hydraulic valves. Rub-ber boot on lever. Spring centering. Lever moves 28° either direction from center. Aluminum body. Up to 4 valves can be ganged together. See web-site for connection kits sold separately.SPECIFICATIONS • Pressure 700 PSI max• Ports SAE 4 (7/16-20 ORB)• Mount Two 1/4˝ coun-

tersunk holes on 4.72˝ centers

• Size 53/8˝ x 13/4˝ x 101/4˝• Shpg 3 lbs.

Order Online www.surpluscenter.com or by Phone 1-800-488-3407Complete Order Information And Shipping Rates Can Be Found On Pages 104 - 106

32.3 cu inHydraulic MotorITEM 9-12448 $399.95• New. Parker TG series hydraulic wheel motor.SPECIFICATIONS • Model TG0530LS08AARD• Disp. 32.3 cu. in. / rev.• Rotation Reversible• Pressure: 2000 PSI cont. 2500 PSI int.• Torque: 8701 in-lbs. cont. 11086 in-lbs. int.• Speed: 213 RPM int.

• Flow: 20 GPM cont. 30 GPM int.• Mount 4 hole wheel

mount.• Shaft 11/4˝ tapered x

2.43˝ long w 5/16˝ keyway, threaded 1˝-20

• Ports SAE 10 side ports• Case Drain None• Size 7.67˝ x 5.314˝ x

5.314˝• Shpg. 44 lbs.

Prop 65▲!

Prop 65▲!