1501 - e118 - welding technology and codes - 04 - welding
TRANSCRIPT
![Page 1: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/1.jpg)
Welding Design
Module 4
![Page 2: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/2.jpg)
Module 4 – Welding Design
Module 4 – Welding Design
4A – Heat Flow4B – Residual Stress and Distortion4C – Fracture and Fatigue4D – Joint Design4E – Welding Symbols4F M h i l T ti
4-2
4F – Mechanical Testing
![Page 3: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/3.jpg)
Module 4 – Welding Design
Module 4 Learning Objectives
Basic understanding of heat flow, heat flow with moving heat sources, estimation of cooling rates and HAZBasic understanding of residual stress and distortion principles and mitigation methodsUnderstanding of weld design, weld joints and welding symbols
4-3
yBasic understanding and purpose of different types of destructive tests
![Page 4: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/4.jpg)
Heat Flow
Module 4A
![Page 5: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/5.jpg)
Module 4 – Welding Design Heat Flow
Heat Flow
ConductionRadiationConvection
radq& .convq& 1θairθ
4-5
.condq&
oθ
![Page 6: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/6.jpg)
Module 4 – Welding Design Heat Flow
Conduction
Fourier’s Law of Conduction
Heat flow
4-6
dx
d
A
xx
θλ−=⎟⎠⎞
⎜⎝⎛=&
Heat flux Thermal
conductivity
Temp. gradient
![Page 7: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/7.jpg)
Module 4 – Welding Design Heat Flow
1-D Conduction
oθ ∞θdxx
4-7
Aqx&Q&
pCρ
dx
Aq dxx+&
Heat generation per unit volume
x
Cross sectional Area A
![Page 8: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/8.jpg)
Module 4 – Welding Design Heat Flow
Conservation of Energy
Internal energy = energy in – energy out
DensitySpecific heat
4-8
p x x dxC Adx QAdx q A q At
θρ +∂ = + −∂
& & &
Internal Energy change = Internal heat generation + heat in – heat out
Density
![Page 9: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/9.jpg)
Module 4 – Welding Design Heat Flow
Conservation of Energy
dxq
qq xxdxx
x
∂∂
+=+&
&&
But using Taylor series expansion,
4-9
x∂
dxAq
AqAqAdxQAdxt
C xxxp x∂
∂−−+=∂∂∴
&&&&θρ
x∂∂−=
∂∂∴ x
p
tC
&&θρ
![Page 10: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/10.jpg)
Module 4 – Welding Design Heat Flow
Conservation of Energy
⎟⎟⎞
⎜⎜⎛ ∂∂∂qx θλ
&
Using Fourier’s law of conduction
4-10
⎟⎟⎠
⎜⎜⎝ ∂−
∂=
∂ x
qx λxx
xpC Qt x
θ θρ λ∂ ∂ ∂⎛ ⎞= + ⎜ ⎟∂ ∂ ∂⎝ ⎠&
Thus,
![Page 11: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/11.jpg)
Module 4 – Welding Design Heat Flow
1-D Conduction
Cθ θρ λ∂ ∂ ∂⎛ ⎞= ⎜ ⎟
To make problem manageable, assume
no internal heat generation
4-11
pCt x x
ρ λ= ⎜ ⎟∂ ∂ ∂⎝ ⎠
2
2pCt x
θ θρ λ∂ ∂=∂ ∂
2 2
2 2
p
kt C x x
θ λ θ θρ
⎛ ⎞∂ ∂ ∂= =⎜ ⎟∂ ∂ ∂⎝ ⎠
λ is constant, not dependent on x or temperature
κ=thermal diffusivity
2m
sec
⎛ ⎞⎜ ⎟⎝ ⎠
![Page 12: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/12.jpg)
Module 4 – Welding Design Heat Flow
Conservation of Energy (Con’t)
1,0 θθ ==t
0,0 θθ ==t
0θθ =
x
L
4-12
1θ
2θ
0 Lx
statesteady −∞=tt
![Page 13: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/13.jpg)
Module 4 – Welding Design Heat Flow
1-D ConductionSteady State without Internal Heat Generation
tQ
x ∂∂+=
∂∂ θ
κθ 12
2&
0
∂θ
General Solution
0
4-13
02
2=
∂
∂
x
θ
1cx
=∂∂θ
21 cxc +=θ
Giving,
![Page 14: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/14.jpg)
Module 4 – Welding Design Heat Flow
Concept of Thermal Resistance
1θ⎯→⎯q&
&21
thermalRθθ −
=
4-14
2θ
1V 2V⎯→⎯
ii
VV 21electricalR
−=
q
![Page 15: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/15.jpg)
Module 4 – Welding Design Heat Flow
Concept of Thermal Resistance
LA
LA
xAq 2112but
θθλ
θθλθλ
−=
−−=
∂∂
−=&
4-15
A
L
LA λθθλ
θθ=
−−
=21
21thermalR
![Page 16: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/16.jpg)
Module 4 – Welding Design Heat Flow
Composite Walls
1θ
θ
x→
4-16
1θ 2θ1R 2R
3θ
2θ3θ
1L 2L
![Page 17: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/17.jpg)
Module 4 – Welding Design Heat Flow
Consider an extrusion process
v
diex
1-D Conduction with Mass Movement
4-17
dx
dxx x+dx
Cρ
Q&
xCVθρ dxxCV +θρ
xq& dxxq +&
![Page 18: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/18.jpg)
Module 4 – Welding Design Heat Flow
1-D Conduction with Mass Movement
Applying conservation of energy to the control volume
ACVACVAqAqAdxQAdxt
C dxxxdxxx ++ −+−+=∂∂ θρθρθρ &&&
4-18
Using Taylor series expansion and simplifying
xCV
x
tC x
∂∂−
∂∂−=
∂∂ θρθρ &&
Using Fourier’s Law of Conduction
xCV
xQ
tC
∂∂−
∂∂+=
∂∂ θρθλθρ
2
2&
![Page 19: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/19.jpg)
Module 4 – Welding Design Heat Flow
1-D Conduction with Mass Movement
In this case if you look at some location x with respect to time, the temperature at that location will remain constant (assuming we are past the transients fromstarting the process). Therefore, we can model this asa Quasi-Steady problem.
4-19
xCV
xQ
tC
∂∂−
∂∂+=
∂∂ θρθλθρ
2
2&
0
xCV
xQ
∂∂−
∂∂+= θρθλ
2
2
0 &
![Page 20: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/20.jpg)
Module 4 – Welding Design Heat Flow
1-D Conduction with Mass Movement
If the cross section of the rod is small, we can assumethat the temperature is constant at every cross section.In that case we can consider the heat loss due toconvection as a negative internal heat generation rate.
4-20
Consider some cross section of area A and perimeter P
A
P
( ) ( )∞∞ −−=⇒−−= θθθθA
hPQhPdxAdxQ &&
![Page 21: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/21.jpg)
Module 4 – Welding Design Heat Flow
1-D Conduction with Mass Movement
( ) 02
2
=−−∂∂−
∂∂
∞θθθρθλA
hP
xCV
xTherefore,
( )2
2
2
2 'and,
','
∂∂=
∂∂
∂∂=
∂∂−= ∞
θθθθθθθLet
4-21
( )22 xxxx ∂∂∂∂
0'''
2
2
=−∂∂−
∂∂ θ
λθ
κθ
A
hP
x
V
xGiving,
Solving,
⎟⎟⎟
⎠
⎞
⎜⎜⎜
⎝
⎛
⎟⎟
⎠
⎞
⎜⎜
⎝
⎛+⎟
⎠⎞
⎜⎝⎛++
⎟⎟⎟
⎠
⎞
⎜⎜⎜
⎝
⎛
⎟⎟
⎠
⎞
⎜⎜
⎝
⎛+⎟
⎠⎞
⎜⎝⎛−= x
A
hPVVCx
A
hPVVCx
λκκλκκθ
2
2
2
1 22exp
22exp)('
![Page 22: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/22.jpg)
Module 4 – Welding Design Heat Flow
1-D Conduction with Mass Movement
∞→x
Applying the boundary conditions.
As then 0'=θ
⎞⎛ ⎞⎛⎞⎛ ⎞⎛
0 ∞
4-22
⎟⎟⎟
⎠
⎞
⎜⎜⎜
⎝
⎛∞⎟⎟
⎠
⎞
⎜⎜
⎝
⎛+⎟
⎠⎞
⎜⎝⎛++
⎟⎟⎟
⎠
⎞
⎜⎜⎜
⎝
⎛∞⎟⎟
⎠
⎞
⎜⎜
⎝
⎛+⎟
⎠⎞
⎜⎝⎛−=∞=
A
hPVVC
A
hPVVCx
λκκλκκθ
2
2
2
1 22exp
22exp)('
Since the second term goes to infinity than 02 =C
![Page 23: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/23.jpg)
Module 4 – Welding Design Heat Flow
1-D Conduction with Mass Movement
0=xAt then ( ) diedie '' θθθθ =−= ∞
⎟⎞
⎜⎛
⎟⎞
⎜⎛
+⎟⎞
⎜⎛
0')0('2
hPVVCθθ
1
4-23
⎟⎟⎟
⎠⎜⎜⎜
⎝⎟⎟
⎠⎜⎜
⎝+⎟
⎠⎞
⎜⎝⎛−=== 0
22exp')0(' 1 A
Cx die λκκθθ
Therefore,dieC '1 θ=
⎟⎟⎟
⎠
⎞
⎜⎜⎜
⎝
⎛
⎟⎟
⎠
⎞
⎜⎜
⎝
⎛+⎟
⎠⎞
⎜⎝⎛−= x
A
hPVVx die λκκ
θθ2
22exp')('
giving,
![Page 24: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/24.jpg)
Module 4 – Welding Design Heat Flow
Heat Flow with Moving Coordinate System
Consider a very large and very thin plate – thickness (h)
y y ddy
4-24
1 2 3 4
yx V
y
wdw
![Page 25: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/25.jpg)
Module 4 – Welding Design Heat Flow
Heat Flow with Moving Coordinate System
t i t
43 5 6 7steady-quasi
final
oθθ −
4-25
transient2
1
time
w x Vt= −
Moving with the welding arc in quasi-steady region, the temperature is constant with respect to time. Form a new moving coordinate system:
![Page 26: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/26.jpg)
Module 4 – Welding Design Heat Flow
Heat Flow with Moving Coordinate System
( )p wC V dy hρ θ
dyyq +&
( )p w dwC V dy hρ θ
+
4-26
dy
dw
wq&
yq&
dwwq +&pCρ Q&
![Page 27: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/27.jpg)
Module 4 – Welding Design Heat Flow
Heat Flow with Moving Coordinate System
( )y y dy
qq q dw h dy dw h
y+∂− = −∂&
& &
Balance heat flow in y direction,
4-27
y∂
( ) ( ) ( )( )
w w dw p pw dw w
p
q q dy h C V C V dy h
qdw dy h C V dw dy h
w w
ρ θ ρ θ
ρ θ
+ +⎡ ⎤− + − =⎣ ⎦
∂ ∂− +∂ ∂
& &
&
Balance heat flow in w direction,
![Page 28: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/28.jpg)
Module 4 – Welding Design Heat Flow
Heat Flow with Moving Coordinate System
Conservation of energy for control volume
( )p p
q qC dydwh Q dydwh dwdyh C V dwdyh
t y w w
θρ ρ θ∂ ∂ ∂ ∂= − − +∂ ∂ ∂ ∂
& &&
4-28
( )p p wC Q C vt w w y y w
θ θ θρ λ λ ρ θ⎛ ⎞∂ ∂ ∂ ∂ ∂ ∂⎛ ⎞= + + +⎜ ⎟⎜ ⎟∂ ∂ ∂ ∂ ∂ ∂⎝ ⎠ ⎝ ⎠&
Conduction Convection
y
Using Fourier’s Law of Conduction
![Page 29: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/29.jpg)
Module 4 – Welding Design Heat Flow
Heat Flow with Moving Coordinate System
2 2θ θ θ θ∂ ∂ ∂ ∂&
Assuming constant properties and constant heat source velocity.
4-29
2 2p pC Q C Vt w y w
θ θ θ θρ λ λ ρ∂ ∂ ∂ ∂= + + +∂ ∂ ∂ ∂
2 2
2 2
V
w y k w
θ θ θ∂ ∂ ∂+ = −∂ ∂ ∂
For quasi-steady,
![Page 30: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/30.jpg)
Module 4 – Welding Design Heat Flow
Heat Flow with Moving Coordinate System3-D Solution for Semi-infinite Plate
2 2 2θ θ θ θ θ∂ ∂ ∂ ∂ ∂&
Assuming constant properties and constant heat source velocity.
4-30
2 2 2p pC Q C Vt w y z w
θ θ θ θ θρ λ λ λ ρ∂ ∂ ∂ ∂ ∂= + + + +∂ ∂ ∂ ∂ ∂
2 2 2
2 2 2
V
w y z k w
θ θ θ θ∂ ∂ ∂ ∂+ + = −∂ ∂ ∂ ∂
For quasi-steady,
![Page 31: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/31.jpg)
Module 4 – Welding Design Heat Flow
Heat Flow with Moving Coordinate System3-D Solution for Semi-infinite Plate
4-31
![Page 32: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/32.jpg)
Module 4 – Welding Design Heat Flow
Heat Flow with Moving Coordinate System3-D Solution for Semi-infinite Plate
4-32
![Page 33: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/33.jpg)
Module 4 – Welding Design Heat Flow
Heat Flow with Moving Coordinate System3-D Solution for Semi-infinite Plate
4-33
![Page 34: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/34.jpg)
Module 4 – Welding Design Heat Flow
Heat Flow with Moving Coordinate System2-D Solution for Thin Plate
4-34
![Page 35: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/35.jpg)
Module 4 – Welding Design Heat Flow
Heat Flow with Moving Coordinate System2-D Solution for Thin Plate
4-35
![Page 36: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/36.jpg)
Module 4 – Welding Design Heat Flow
Cooling Rate Equation
4-36
![Page 37: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/37.jpg)
Module 4 – Welding Design Heat Flow
Cooling Rate Equation
4-37
![Page 38: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/38.jpg)
Module 4 – Welding Design Heat Flow
Cooling Rate Equation
4-38
![Page 39: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/39.jpg)
Module 4 – Welding Design Heat Flow
Heat Flow with Moving Coordinate SystemPeak Temperature Equations
oθθ −
At the peak temperature the slope of the temperature time curve must be zero.
4-39
0peak at =∂∂
t
θ
t
![Page 40: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/40.jpg)
Module 4 – Welding Design Heat Flow
Heat Flow with Moving Coordinate SystemPeak Temperature Equations
We previously derived
t
θ∂∂
( )2
21 0
t 2 2
Vw rP w V w
V er r r
κθπ λ κ
− + ⎡ ⎤∂ ⎛ ⎞= − − − + =⎜ ⎟⎢ ⎥∂ ⎝ ⎠⎣ ⎦
4-40
t 2 2r r rπ λ κ∂ ⎝ ⎠⎣ ⎦
Therefore,2
1 02
w V w
r rκ⎛ ⎞− − + =⎜ ⎟⎝ ⎠
Find relationship between w and r when the pointof interest reaches the peak temperature and then use thick plate solution to find peak temp.
( )2
2
Vw r
peak o
Pe
rκθ θ
π λ− +
− =
![Page 41: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/41.jpg)
Module 4 – Welding Design Heat Flow
Peak Temperature Equations
We force the eq. to fit experimental results by specifying a known temperature θr at known location rr . Then,
ora
rp
opV
EI
rrce
θθη
π
θθ −+
⎟⎠⎞
⎜⎝⎛ ⎟
⎠⎞⎜
⎝⎛ −℘
=−
12122
4-41
For example, at fusion boundary θm is the known peak temperature and r=d/2 where (d) is the weld bead with is known location. Then,
oma
p
opV
EI
dyc
e
θθη
π
θθ −+
⎟⎟⎟
⎠
⎞
⎜⎜⎜
⎝
⎛
⎟⎟
⎠
⎞
⎜⎜
⎝
⎛−℘
=−
1221
22
![Page 42: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/42.jpg)
Residual Stress and Distortion
Module 4B
![Page 43: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/43.jpg)
Module 4 – Welding Design Residual Stress and Distortion
Linear Elastic Material
modulus-E
σ( )[ ]
( )[ ]E
E
zxy
zyx
σσνσε
σσνσε
+⋅−=
+⋅−=
1
1
Equationsstrain stress 6
y
x
4-43
ε
( )[ ]
G
G
G
E
E
zxzx
yzyz
xyxy
yxz
xy
τσ
τσ
τσ
σσνσε
=
=
=
+⋅−= 1z
y
Ex
x
σε =
Ex
y
σνε −=E
xz
σνε −=
Hook’s Law Uniaxial Loading
Poisson’s ratio
![Page 44: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/44.jpg)
Module 4 – Welding Design Residual Stress and Distortion
Typical Material (Metal)
stress yieldσ
4-44
ε
model plasticperfectly
elasticlinear Use
![Page 45: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/45.jpg)
Module 4 – Welding Design Residual Stress and Distortion
Thermal Strains
( )coefficient of thermal expansion
x y z oθ θ θε ε ε α θ α θ θ
α= = = Δ = −
=
4-45
e
0
total strain=elastic strain + thermal strain
xy yz zx
t
θ θ θ
θ
γ γ γ
ε ε ε
= = =
= +
![Page 46: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/46.jpg)
Module 4 – Welding Design Residual Stress and Distortion
Linear Elastic Perfectly Plastic Material
t e p θε ε ε ε= + +
4-46
elastic plastic thermal
ε ε ε ε+ +
![Page 47: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/47.jpg)
Module 4 – Welding Design Residual Stress and Distortion
Example
Steel Bar between two rigid walls
y620 10 psiE = ×
4-47
x3
6
50 10 psi
13.8 10
y
o
F
Fα −
= ×
= ×Heating - Elastic Range
0
psi114
t xx
x o
E
EF
σε α θ
σ α θ θ
= = + Δ
∴ = − Δ = − Δ
![Page 48: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/48.jpg)
Module 4 – Welding Design Residual Stress and Distortion
Simple Distortion Example (Transverse Shrinkage)
Restraint and Temp. Distribution
k
θΔ heating Heating
pxx
l
l E
σε α θ εΔ= = + Δ +
4-48
l
stress) (thermal heatingat
lΔ( )
xx
px x
p
x
A k l l Ak
Akl E
E k l
E A k l
σσ
σ σ α θ ε
α θ εσ
= − Δ → Δ = −
⎛ ⎞∴ − = + Δ +⎜ ⎟⎝ ⎠
Δ +∴ = −
+
![Page 49: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/49.jpg)
Module 4 – Welding Design Residual Stress and Distortion
Small Δθ
0=pε
( )
No plastic strain
Then,
4-49
( )KlEA
EKlx +
Δ⋅−= θασ
At the end of cooling there will be no residual stress and no distortion.
![Page 50: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/50.jpg)
Module 4 – Welding Design Residual Stress and Distortion
Large Δθ – at end of heating
Assume 0=pε
Calculate( )
KlEA
EKlx +
Δ⋅−= θασ
4-50
Ifyx F>σ then,
yx F−=σ0≠pε and
θαε Δ⋅−⎟⎠⎞
⎜⎝⎛ +=
EKl
AFy
p 1
![Page 51: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/51.jpg)
Module 4 – Welding Design Residual Stress and Distortion
Large Δθ – at end of Cooling
Assume no additional plastic deformation occurs during cooling.
Calculate ( )EKl p
= εσ
4-51
( )KlEA
EKl p
xres += εσ
Ifyx F<σ then, no plastic deformation occurred
⎟⎠⎞
⎜⎝⎛ +−=
EKl
AFy
p 1ε
during cooling, and
KlEAx +=σ
Ifyx F>σ then, plastic deformation occurred
during cooling, andyx F=σ
![Page 52: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/52.jpg)
Module 4 – Welding Design Residual Stress and Distortion
Three Bar Analogy
Suppose we have 3-bar which have the same cross section area A and same material properties.
heating
4-52
s sm
sσmσ
sσ
![Page 53: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/53.jpg)
Module 4 – Welding Design Residual Stress and Distortion
Three Bar Analogy
Jig or fixture used (restraint) during heatingSmall heating
4-53
s sm
0
0
p
tx
εε
==
, 0
comp. spring case
p pmtm m m
m
EE
σε α θ ε ε
σ α θ
∴ = + Δ + =
∴ = − Δ ⋅
![Page 54: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/54.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Significance of Residual Stress and Distortion
Residual StressDegraded Structural PerformanceReduced Service LifeDimensional Instability
Distortion
4-54
Dimensional Tolerance and Fit-up ProblemsReduced StrengthReduced Structural StabilityInadequate Appearance
![Page 55: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/55.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Welding Processes and Their Consequences
During WeldingLocalized Heat Source (heating, melting solidification, and cooling)Non-uniform Temperature Distribution (thermal/mechanical mismatch)Fast Cooling Rate (phases with volume expansion)Weld Shrinkage (shrinkage strains created in weld & surrounding metal)R t i t (i t l i idit d/ t l t i t ti
4-55
Restraints (internal rigidity and/or external constraints preventing shrinkage)Initial Stress Condition (influence thermal strain and residual stress)Properties of Parent Material (temperature dependent yield stress and Modulus of elasticity)
After Welding• Residual Stresses• Distortion
![Page 56: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/56.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Residual Stresses & Distortion Flowchart
4-56
![Page 57: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/57.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Factors Influencing Residual Stresses & Distortion
Physical Material PropertiesCoefficient of thermal expansion, [α (1/°K)]
As α increases distortion increases
Thermal conductivity, λ (W/(m·°K))As λ increases distortion decreases
Mechanical Material Properties
4-57
Yield stress, Fy (ksi), modulus of elasticity, E(ksi)
Welding Process VariablesHeat input, travel speed, welding sequence
Jigs and Fixtures or other Clamping DevicesGeometrical Properties
Moment of inertia, weld cross sectional area, weight of weld metal, plate thickness, joint geometries, weld length
![Page 58: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/58.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Comparison of Material Properties
Properties
Materials
Mechanical Properties Thermal Properties
Fult
[MPa]Fy
[MPa]e
[%]E
[GPa]CTE 20 °C[mm/m°C]
rCp
[J/m3/°C]x106
l[W/m-K]
Tm
[°C]Tliq
[°C]
NICKEL BASEINCONEL 718 1375 1100 25 207 13 3.56 11.4 1298 1336
4-58
TITANIUM TI-6AL-4V 1170 1100 10 114 8.6 2.33 6.7 1660 1660
ALUMINUM2014 185 95 18 72.4 23 2.46 192 507 638
STAINLESS STEEL 304 505 215 70 197 17.3 4.00 16.2 1427 1455
![Page 59: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/59.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Non-Linear Distribution of Temperature andResulting Residual Stress
DT = 0 Stress = 0
Tension
x
A AB BO
YMelted region
1. Section A-A
4-59
2. Section B-B
3. Section C-C
4. Section D-D
Compression
DT = 0 Residual stresses
C C
D D
Plastic deformationoccurs
g
Reference: Welding Handbook, Volume 1, AWS, 1991
![Page 60: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/60.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Residual Stresses in Butt Joint
(A) Distribution of σx Along YY
Tension
Compression
σx
Y
X
4-60
Y
curve 2
curve 1Tension
Compression
σy
Reactionstress
(B) Distribution of σy Along XX
Reference: Welding Handbook, Volume 1,
AWS, 1991
![Page 61: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/61.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Fundamental Types of Weld Distortion
(a) Transverse Shrinkage
(b) Angular Change
(d) Longitudinal Shrinkage
(e) Longitudinal Bending
4-61
(c) Rotation Distortion (f) Buckling Distortion
Reference: Welding Handbook, Volume 1, AWS, 1991
![Page 62: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/62.jpg)
Module 4 – Welding Design Residual Stress and Distortion
Compatibility
4-62
y
x
![Page 63: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/63.jpg)
Module 4 – Welding Design Residual Stress and Distortion
Compatibility
2-D Elastic Compatibility
02
2
2
2
2
=∂∂
∂−
∂∂
+∂∂=
yxxyR xyyx
γεε
4-63
yy
2-D Inelastic Compatibility
02
2
2
2
22
2
2
2
2
=⎥⎥⎦
⎤
⎢⎢⎣
⎡
∂∂′′∂
−∂
′′∂+
∂′′∂+
⎥⎥⎦
⎤
⎢⎢⎣
⎡
∂∂′∂
−∂
′∂+
∂′∂=′′+′
yxxyyxxyRR xyyxxyyx
γεεγεε
Elastic Inelastic (thermal & plastic)
![Page 64: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/64.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Rotational Distortion in Butt Joints
Unwelded Portion of the Joint Closes
4-64
Unwelded Portion ofthe Joint Opens
Reference: Masubuchi, K. Analytical Investigation of Residual Stresses and Distortions Due to Welding. Welding Journal 39 (12): 525s-537s (1960)
In-Plane Distortion Due to Cutting
Back Weld to Maintain Joint Opening
![Page 65: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/65.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Longitudinal and Transverse Weld Shrinkagein Butt Joints
4-65
![Page 66: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/66.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Effect of Groove Detail and Joint Thicknesson Transverse Shrinkage
rin
kag
e (i
n.) 0.15
0.10
4-66
Area of Weld (in.2)
Tran
sver
se S
hr
Reference: Design of Weldments, Omer W. Blodgett, 1976
1/4 1/2 3/4 1 1-1/4 1-1/2
0.05
0
Plate Thickness (in.)
![Page 67: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/67.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Effect of Weight of Weld Metal on Transverse Shrinkage
4-67
Increases of Transverse Shrinkage During Multipass Welding of A Butt Joint
Reference: K. Masubuchi, Analysis of Welded Structure, Pergamon Press
![Page 68: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/68.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Transverse Shrinkage Causing Angular Distortion
4-68
Non-uniform Transverse Weld Shrinkage in Butt Joints
Transverse Weld Shrinkage in Fillet Welded Tee-Joints
![Page 69: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/69.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Moment of Inertia Effect on AngularDistortion in Butt Joint
Balancing the Multi-pass
4-69
g pWeld Decreases Angular Distortion of Butt Joints
![Page 70: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/70.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Moment of Inertia Effect on Angular Distortion in Tee-Joint
Throat CG of weldsMoment arm
Neutralaxis (a) Fillet Weld T- Joint
4-70
Throat CG of welds Moment arm
Neutral axis
axis
(b) Deeper Penetration Weld
(a) Fillet Weld T Joint
Reference: Design of Weldments, Omer W. Blodgett, 1976
![Page 71: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/71.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Angular Change in Fillet Welds – UnrestrainedAngular Change of Unrestrained Fillet Weld
(A) Steel (B) Aluminum
4-71
Determination of the Angular Change of Unrestrained Steel and Aluminum Fillet Welds by Plate Thickness and Fillet Weight per Unit Length of Weld
Reference: Welding Handbook, Volume 1, AWS, 1991
![Page 72: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/72.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Angular Distortion in Fillet Welded Framing Structures
φo
4-72
(A) Free Joint (Unrestrained)
(B) Restrained Joint
φ δ
xL
Reference: Welding Handbook, Volume 1, AWS, 1991
![Page 73: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/73.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Angular Distortion
L
4-73
Longitudinal Bending
Angular Pipe Bending
L
![Page 74: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/74.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Effect of Fillet Weld Size on Longitudinal Deflection
4-74
Effect of Fillet Weld Size on Longitudinal Deflection in T-
Section Beams
Reference: Welding Handbook Volume 1, AWS, 1991
![Page 75: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/75.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Distortion Comparison Between Steel and Aluminum Weldments
Transverse Shrinkage of Butt Joint
Aluminum > Steel
4-75
Longitudinal Bending Distortion
Aluminum < Steel
![Page 76: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/76.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Distortion Comparison Between Steel and Aluminum Weldments
Angular Change of a Fillet Weld Al < St
4-76Reference: Welding Handbook,Volume 1, AWS, 1991
![Page 77: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/77.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Reduce the Amount of Welding Decrease Weld Deposit
Reduce bevelangle and use larger
root opening
1/32” to 1/16”
30 °
4-77
Double-V preparation
1/32” to 1/16”
U preparation
Example: Edge Preparation and Fitup
![Page 78: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/78.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Reduce the Amount of WeldingUsing Intermittent Welding Technique
4-78Reference: Design of Weldments, Omer W. Blodgett, 1976
Decreasing Length of Weld by UsingIntermittent Welding Technique
![Page 79: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/79.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Reduce the Amount of Welding Decrease Leg Size
4-79
Decrease Leg Size of Weld Decrease Shrinkage Forceand the Tendency to Distortion
Reference: Design of Weldments, Omer W. Blodgett, 1976
![Page 80: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/80.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Minimize Welding Time
(a) 170 amp 25 volt 3 in/min Thick Plate
Variance of Welding Technique. In Each Case, Surface Isotherm of 300°F is Shown Surrounding Welding Source
4-80
(b) 170 amp 25 volt 6 in/min Thick Plate
(c) 340 amp 30 volt 6 in/min Thick Plate Solid Curve310 amp 35 volt 8 in/min Thick Plate Dashed Curve (Same size weld)
(d) 170 amp 25 volt 22 in/min Sheet (t=0.1345 in) Reference: Design of Weldments, Omer W. Blodgett, 1976
![Page 81: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/81.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Presetting the Joints
Before Welding
After Welding
4-81Reference: Design of Weldments, Omer W. Blodgett, 1976
The net effect of weld shrinkage pulls the member or
connection back into proper alignment.
![Page 82: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/82.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Examples of Presetting the Joints
(a) (b)(d)
4-82
(a) (b) Girder, (c) Plate, (d) Fixing of Groove Gap by Wedge in Single Pass Gas Welding
Pre-welding Position Traced in Solid LinesPost-welding Position in Broken Lines
(c)
Reference: D. Radaj, Heat Effects of Welding, Springer-Verlag, 1992
![Page 83: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/83.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Preheat the Joint
Effect of Preheat and
4-83
Reference: Kihara, H., Watanabe, M., Masubuchi, K., and Satoh, K., “Researches on Welding stress and shrinkage distortion in Japan”, 60th Anniversary Series of the Society of Naval Architects of Japan, Vol. 4, 1959
Effect of Preheat and Welding Variables on
Angular Change of Steel Fillet Welded T-Joints
![Page 84: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/84.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Prestrain the Joint
(a) Elastic Prestraining
4-84Reference: Kumose, T., Yoshida, T., and Onoue, H, Prediction of angular distortion caused by one-pass fillet welding, The Welding Journal, 33, 945-956 (1954)
(b) Plastic Prebending
(a) Elastic Prestraining
![Page 85: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/85.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Example of Elastic Prestraining
4-85
Apparatus for Welding T-Joints Submitted to Elastic Prestrain by Bolting Down Both Free Ends
Reference: Welding Handbook, Volume 1, AWS, 1991
![Page 86: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/86.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Examples of Plastic Prestraining
(a)
(b)
( )
4-86
(a) Roof Shaping of Girder Chords(b) Plane End Section of Cylindrical Shell(c) Outward Bulging of Spherical Shell with Block Flange(d) Outward Bulging of Pipe with Circumferential Weld(e) Inward Drawing of Pipe at Plane End
(c)
(d) (e)
Reference: D. Radaj, Heat Effects of Welding, Springer-Verlag, 1992
![Page 87: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/87.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Use as Few Weld Passes as Possible
PoorFigure (a)
4-87
Minimum Number of Passes
Good Figure (b)
![Page 88: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/88.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Place Welds Near the Neutral Axis
4-88
![Page 89: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/89.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Plan the Welding Sequence Welds are Symmetrical about Neutral Axis
No. 1No. 4 No.1 No.1
3/16” to 3/8”mild steel channel
y y
x x x
4-89
No. 2 No. 3 No.2
(a) (b) (c)
channel
y y
x x x
Reference: Design of Weldments, Omer W. Blodgett, 1976
![Page 90: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/90.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Plan the Welding Sequence Welds are Symmetrical about Neutral Axis
No.1 No.1 No.1No.4No.4
4-90
No.2 No.3No.3(d) (e) (f)
Reference: Design of Weldments, Omer W. Blodgett, 1976
![Page 91: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/91.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Plan the Welding SequenceLong and Thin Box Sections
(Turn the Members Quickly to Protect the Weld from Cooling)
(a) During Welding, Top Expands- Center Bows Up
Temperature Distribution - Cross
Section
4-91
(b) Shortly after Welding -Still Bowed up Slightly
(c) After Cooled - End VerySlightly Bowed up due to Contraction of Top
Reference: Design of Weldments, Omer W. Blodgett, 1976
![Page 92: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/92.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Place Welds Near the Neutral Axis –Three -Member Column
9”1-3/4”
2-1/2” NeutralNeutral 0 556”0 682”
4-92
2-1/2
5/8” CG of welds CG of welds
Neutralaxisaxis
0.5560.682
(a) (b)
Reference: Design of Weldments, Omer W. Blodgett, 1976
![Page 93: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/93.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Plan the Welding Sequence – Multi-Layer Welding
1
4
4-93
12
3
An Example of a Double V-Groove Butt Joint. Suitable Welding Sequence in Multi-layer Welding can Reduce Angular Distortion
![Page 94: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/94.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Plan the Welding Sequence – Multi-Layer Welding
4-94
Reduction of Angular Distortion by Alternating Weld Pass Deposition in Double-V Groove
(a) (b) (c)
Reference: D. Radaj, Heat Effects of Welding, Springer-Verlag, 1992
![Page 95: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/95.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Plan the Welding Sequence – Backstep Welding
3 D
DB
Direction ofeach beadsegment
4-95
1
2
C
C
A Direction of Welding
![Page 96: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/96.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Plan the Welding Sequence – Backstep Welding
4-96
Reduction of Transverse Shrinkage as well as Groove Gap Distortion by Back-Step Welding: Tack Weld Sequence (a), Back-
Step Welding Sequence in First Layer (b) and Cover Pass (c)
Reference: D. Radaj, Heat Effects of Welding, Springer-Verlag, 1992
![Page 97: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/97.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Distortion Control by Welding Sequence –Welding Sequences
Unwelded Spaces Filled After Deposition of Intermittent Blocks
4-97
(A) Backstep Sequence (B) Block Sequence
(C) Built-up Sequence (D) Cascade Sequence
Reference: K. Masubuchi, Analysis of Welded Structure, Pergamon Press
![Page 98: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/98.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Methods of Removing Distortion –Flame (Thermal) Straightening
Line heatingPine-needle heatingHeating in cross sectionSpot heatingTriangular heatingR d h t h ti
4-98
Red-hot heating
Reference: Analysis of Welded Structures, Koichi Masubuchi
![Page 99: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/99.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Methods of Removing Distortion –Flame (Thermal) Straightening
4-99
Line Heating Pine-needle Heating Heating in CrossDirections
Reference: Analysis of Welded Structures, Koichi Masubuchi
![Page 100: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/100.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Methods of Removing Distortion –Flame (Thermal) Straightening
.........
.........
4-100
.........
.........Spot Heating Triangular Heating Red-hot Heating
Reference: Analysis of Welded Structures, Koichi Masubuchi
![Page 101: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/101.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Methods of Removing Distortion –Flame (Thermal) Straightening
4-101
(a) Spot Shape (b) Strip Shaped (c) Wedge Shaped
Application of Flame Straightening
Reference: D. Radaj, Heat Effects of Welding, Springer-Verlag, 1992
![Page 102: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/102.jpg)
Module 4 – Welding Design Residual Stress and DistortionResidual Stress and Distortion
Methods of Removing Distortion –Flame (Thermal) Straightening
(a) (b)
4-102
(c) (d)
Flame Straightening by Means of Heat Strips and Heat Wedges in Different Arrangement on Bending-Distorted Girders
Reference: Vinokurov, V. A., Welding stresses and distortion, Wetherby:British Library 1977
![Page 103: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/103.jpg)
Fracture and Fatigue
Module 4C
![Page 104: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/104.jpg)
Module 4 – Welding Design Fatigue and Fracture
Linear Elastic Fracture Mechanics
. material for the
modulus sYoung' torelated becan
strength tensile thesolid,perfect aFor
T
E
σ
4-104
20 to
10
EET =σ
psi 10 to105 isit actually while
psi 10 be would thisglass,For 53
6
×
=Tσ
![Page 105: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/105.jpg)
Module 4 – Welding Design Fatigue and Fracture
Brittle Fracture
Griffith – glassy materials contain crack like defects which act as stress raisers.
4-105
c2
cσ
fracture of
energy surface
2
=
=
s
sc c
E
γ
πγσ
![Page 106: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/106.jpg)
Module 4 – Welding Design Fatigue and Fracture
Brittle Fracture
getsone,For
221
cracks sharp longFor
=
≅+≅
Ea
c
a
cSCF
Tσ
4-106
oA 10,000 - 100or distances atomic
2500 to25order of lengths gets one
glasses,in lengthscrack gcalculatinBack
Criterion sGriffith' toresultssimilar gives 20
getsone ,10
For
→≅c
aEc
T
σ
σ
![Page 107: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/107.jpg)
Module 4 – Welding Design Fatigue and Fracture
Linear Elastic Fracture Mechanics
Mode I
∞22σ
4-107
c2
2x
1x
θ
r
pR zone
plastic
∞22σ
![Page 108: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/108.jpg)
Module 4 – Welding Design Fatigue and Fracture
Linear Elastic Fracture Mechanics
∞σ
y
4-108
c2
cKI πσ ∞=y
x
z
∞σ
For r=0 stresses are infinite!Is this realistic?
![Page 109: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/109.jpg)
Module 4 – Welding Design Fatigue and Fracture
Linear Elastic Fracture Mechanics
y
y
x
z
4-109
y
x
z
z
Mode II Mode III
![Page 110: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/110.jpg)
Module 4 – Welding Design Fatigue and Fracture
Stress Intensity Factors
Stress intensity factor is used to find the stress distribution and magnitude near the crack tip. It is a function of:
σ = applied stress
c = half crack length (full crack length for edge cracks)
4-110
( ) cw
fwcK πσσ ⎟⎠⎞
⎜⎝⎛= c
,,
w= characteristic dimension for the part
Determined analytically or experimentally as well as by finite element analysis.
![Page 111: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/111.jpg)
Module 4 – Welding Design Fatigue and Fracture
Fracture Toughness (Kc)
Kc is a material property which indicates the stress intensity factor above which crack extension will occurKIC (the plane strain value of Kc) is a linear elastic facture mechanics parameter which can be used for brittle fracture
For real materials, some plastic deformation will occur near the crack tip.
4-111
σ
yF
xpr
Linear elastic
Real material
![Page 112: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/112.jpg)
Module 4 – Welding Design Fatigue and Fracture
Fracture Toughness
( ) ⎥⎦
⎤⎢⎣
⎡⎟⎠⎞
⎜⎝⎛⎟⎠⎞
⎜⎝⎛ +⎟
⎠⎞
⎜⎝⎛=
2sin
2sin1
2cos
2
θθθπ p
Iy
r
KF
For plane stress, the size of the plastic zone is found from
where for θ=00
4-112
( )p
Iy
r
KF
π2=
2
2
1⎟⎟
⎠
⎞
⎜⎜
⎝
⎛=
y
Ip
F
Kr
π
For plane strain,
2
6
1 ⎟
⎟
⎠
⎞
⎜⎜
⎝
⎛=
y
Ip
F
Kr
π
For LEFM the size of the plastic zone must be small
![Page 113: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/113.jpg)
Module 4 – Welding Design Fatigue and Fracture
Fatigue
Fatigue failure resulting from cyclic deformation with large plastic strain amplitude is called low cycle fatigue
Failure usually occurs in ten to several hundred cycles
Fracture resulting from many thousands of stress cycles below the elastic limit are called high cycle fatigue
4-113
g y g
Phases for Fatigue FailureCrack initiation – stress concentrations at grain boundaries or flawsCrack propagation – The crack propagates on every cycle of loadingFracture – crack long enough for fracture to occur when maximum stress is reached
![Page 114: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/114.jpg)
Module 4 – Welding Design Fatigue and Fracture
S-N Curvetu
de Ferrous CNm
a =σ
4-114
Log N
Str
ess
amp
li
Non-ferrous Fatigue Limit
![Page 115: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/115.jpg)
Module 4 – Welding Design Fatigue and Fracture
Nonzero Mean Stress
σStress
max
minσσ
=R 1−=RStress ratio Tension-compression
4-115
aσ
aσ
maxσ
meanσ
minσ
Time
![Page 116: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/116.jpg)
Module 4 – Welding Design Fatigue and Fracture
Goodman Diagram
cycles 103
cycles104
aσ 1=+ult
m
a
a
oσσ
σσ
4-116
cycles 10
cycles 105
cycles 106
mσultσ
Mean Stress
constant life lines
![Page 117: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/117.jpg)
Module 4 – Welding Design Fatigue and Fracture
Goodman Diagram
cycles 103ultσ
constant life linesmaxσ
4-117
cycles 104
cycles 105
cycles 106
minσ
u t
![Page 118: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/118.jpg)
Module 4 – Welding Design Fatigue and Fracture
Fatigue With Varying Stress Amplitude –Miner’s Rule
1∑ =k
in
Miner’s Rule – each cycle uses a fraction of the fatigue life.
4-118
1∑
=i iN
∑=
=k
i
mi
i
C
n
1
1σ
For fully reversible tension-compression loading from S-N curve one gets,
![Page 119: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/119.jpg)
Module 4 – Welding Design Fatigue and Fracture
Fatigue of Welded Joints
The presence of welded member usually results in drastic reduction in fatigue life or stressCauses: Stress Concentrations – generally a weld introduces stress concentrations
Steel
4-119
510 610 710 810
0=R
Steel
![Page 120: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/120.jpg)
Joint Design
Module 4D
![Page 121: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/121.jpg)
Module 4 – Welding Design Joint Design
Common Design Requirements
Proper Weld Design to Meet Following RequirementsStrength against rupture (excessive yielding)Toughness against fracture, especially under dynamic or impact loading (brittle fracture)Ductility (ability to stretch) to prevent welding-induced cracking or cracks due to excessive deformationFatigue resistance against cyclic loading
4-121
Fatigue resistance against cyclic loading
![Page 122: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/122.jpg)
Module 4 – Welding Design Joint Design
Essential and Related Design Factors
Proper Weld Design to Meet Following RequirementsMaterials
Base Metal (e.g. ASTM A36)Filler Metal (e.g. AWS A5.1)
Joints/WeldsWelding Process(es)/Procedure Qualification
Joint Thickness
4-122
Joint ThicknessPipe Outside DiameterWelding Position
Welder Qualification (per qualified procedure)Workmanship (including distortion control, heat treatment)Inspection
![Page 123: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/123.jpg)
Module 4 – Welding Design Joint Design
Aspects of Weld Design
Structural Connection Design ElementsTypes of Joints and Welds (AWS A3.0 - Standard Terms and Definitions)Welding/NDE Symbols (AWS A2.4 – Standard Symbols for Welding, Brazing, and Nondestructive Examination)Design for Strength
4-123
Design for StrengthDesign for Fracture ResistanceDesign for Fatigue ResistanceEffect of Residual Stress and Distortion
![Page 124: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/124.jpg)
Module 4 – Welding Design Joint Design
Structural Connection Design Elements
Connection TypesNontubular (i.e., plate)Tubular
Basic Joint TypesButt JointTee Joint (including skewed-T)
Basic Weld TypesGroove (CJP, PJP)
Further classifications see AWS A2.4 and A3.0
FilletPlug and SlotContinuous vs Intermittent
4-124
Lap JointCorner JointEdge Joint
Continuous vs. IntermittentOthers for Thin Joints: Spot, Seam
Welding PositionsFlat (1-G or 1-F)Horizontal (2-G or 2-F)Vertical (3-G or 3-F)Overhead (4-G or 4-F)Combination (5-G, 6-G, 6-GR)
![Page 125: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/125.jpg)
Module 4 – Welding Design Joint Design
Basic Joint Types
Butt jointContinuity of section
Tee jointFlanges or stiffeners
Lap jointNo joint preparation
4-125
j p p
Corner jointEdge joint
Two or more parallel, or nearly parallel members
![Page 126: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/126.jpg)
Module 4 – Welding Design Joint Design
LapButt
Weld FaceReinforcement
Joint Type Examples
4-126
Tee
Corner
Edge
![Page 127: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/127.jpg)
Module 4 – Welding Design Joint Design
Basic Joint Type Extension – Flanged Joints
Flange Butt Joints
Flange T-Joint
4-127
Flange Corner Joint
Flange Lap Joints
Flange Edge Joints
![Page 128: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/128.jpg)
Module 4 – Welding Design Joint Design
Butt Joint Extension – Spliced Joints
Single-Spliced Butt Joint Splice Member
4-128
Double-Spliced Butt Joint
Joint Member
Joint Member
SpliceMember
Joint Filler
![Page 129: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/129.jpg)
Module 4 – Welding Design Joint Design
Square
Single-Bevel
Double-J
Flanged Edge
Edge Shapes of Members
4-129
Double-Bevel
Single-J
Round Edge
RoundEdge
![Page 130: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/130.jpg)
Module 4 – Welding Design Joint Design
Joint Design Variables
4-130
Root OpeningGroove RadiusIncluded AngleRoot Face (Land)Dihedral Angle
![Page 131: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/131.jpg)
Module 4 – Welding Design Joint Design
Basic Types of Weld
Fillet
Square Groove
Double-U Groove
Single-Bevel Groove
D bl B l
4-131
Single-V Groove
Double-V Groove
Single-U Groove
Double-Bevel Groove
Single-J Groove
Double-J Groove
![Page 132: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/132.jpg)
Module 4 – Welding Design Joint Design
Basic Types of Weld
4-132
![Page 133: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/133.jpg)
Module 4 – Welding Design Joint Design
Groove Weld Examples
4-133
Single-Square-Groove Weld Single-Bevel-Groove Weld
Single-V-Groove Weld Single-V-Groove Weld(with Backing)
![Page 134: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/134.jpg)
Module 4 – Welding Design Joint Design
Groove Weld Examples
Single Groove Weld Single U Groove Weld
4-134
Single-Groove Weld Single-U-Groove Weld
Single-Flare-Bevel-Groove Weld Single-Flare-V-Groove Weld
![Page 135: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/135.jpg)
Module 4 – Welding Design Joint Design
Groove Weld Examples
D bl S G W ld
4-135
Double-Square-Groove Weld Double-Bevel-Groove Weld
Double-V-Groove WeldDouble-J-Groove Weld
![Page 136: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/136.jpg)
Module 4 – Welding Design Joint Design
Groove Weld Examples
Double-U-Groove Weld
4-136
Double-Flare-Bevel-Groove Weld
Double-Flare-V-Groove Weld
![Page 137: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/137.jpg)
Module 4 – Welding Design Joint Design
Square-Groove Weld and Flare-V-Groove Weld in a
Flare and Edge Welds
4-137
Edge Weld with Melt-through in a Flanged Butt Joint
a e G oo e e d aFlanged Butt Joint
Edge Weld in aFlanged Butt Joint
![Page 138: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/138.jpg)
Module 4 – Welding Design Joint Design
Fillet Weld Examples
4-138
Double Fillet Weld Single Fillet Weld
![Page 139: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/139.jpg)
Module 4 – Welding Design Joint Design
ttt
Area = 0.56t2 Area = 0.25t2 Area = 0.50t2
S 0 75t
(a) (b) (c)
Weld Quantities Comparison
4-139
S = 0.75t
S
Double-Fillet Weld Double-Bevel-Groove Weld
Single-Bevel-Groove Weld
![Page 140: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/140.jpg)
Module 4 – Welding Design Joint Design
Estimated Relative Costs
20
Cos
t
4-140
0 0.5 1.0 1.5 2.0
10
0
Rel
ativ
e C
Plate Thickness, in.
![Page 141: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/141.jpg)
Module 4 – Welding Design Joint Design
Plug Welds Fillet Welds
Plug/Slot Weld vs. Fillet Weld in Hole
4-141
Slot Welds
![Page 142: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/142.jpg)
Module 4 – Welding Design Joint Design
Weld Joint Nomenclature
1
2
53
1
2
3
6
4
5
4-142
1 - groove angle2 - bevel angle3 - root face (land)4 - root opening (root gap)5 - groove face
44
1 - throat2 - weld face3 - depth of fusion4 - root5 - fillet leg length6 - weld toe
![Page 143: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/143.jpg)
Module 4 – Welding Design Joint Design
Weld Toe
Weld FaceFaceReinforcement
RootReinforcement
Groove Weld Nomenclature
4-143
Reinforcement
Root Surface
Weld Root
![Page 144: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/144.jpg)
Module 4 – Welding Design Joint Design
F
FaceReinforcement
Groove Weld MadeBefore Welding Other Side
Groove Weld Nomenclature
4-144
FaceReinforcement
Back WeldGroove Weld Made After Welding Other Side
Weld Root
Backing Weld
![Page 145: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/145.jpg)
Module 4 – Welding Design Joint Design
Actual Throat
EffectiveThroat
Convexity
Leg & Size
Leg & Size
Leg
Fillet Weld: Convex and Concave
4-145
Theoretical Throat Actual ThroatEffective throat
Theoretical Throat
Concavity
Leg
Size
Size Leg
![Page 146: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/146.jpg)
Module 4 – Welding Design Joint DesignJoint Design
Effective Weld Throat for Design Calculations
4-146
Convexity Concavity
![Page 147: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/147.jpg)
Module 4 – Welding Design Joint DesignJoint Design
Stringer Bead
Welding Technique
4-147
Weave Bead
![Page 148: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/148.jpg)
Module 4 – Welding Design Joint Design
Weld Beads
Weld Beads vs. Weld Layers
4-148
Layers
Weld Beads
Layers
![Page 149: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/149.jpg)
Module 4 – Welding Design Joint Design
ASME Section IX –Joint Procedure Variables
Paragraph Brief of Variables EssentialSupplementary
Essential Nonessential
.1 φ Groove Design X X X
.2 ± Backing X X
.4 - Backing
.5 + Backing
6 > Fit-up Gap X X
4-149
QW-402 Joints
.6 > Fit-up Gap X X
.10 φ Root Spacing X
.11 ± Retainers X X
.18 φ Lap Joint Configuration X
![Page 150: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/150.jpg)
Module 4 – Welding Design Joint Design
ASME Section IX –Base Material Procedure Variables
Paragraph Brief of Variables EssentialSupplementary
Essential Nonessential
QW-403
.2 Maximum T Qualified X
.3 φ Penetration X
.6 T Limits X
.8 φ T Qualified X
9 t pass > 1/2-in X
4-150
Q 03Base Materials
.9 t pass > 1/2-in. X
.10 T Limits (S. Cir. Arc) X
![Page 151: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/151.jpg)
Module 4 – Welding Design Joint Design
ASME Section IX –Technique Procedure Variables
Paragraph Brief of Variables EssentialSupplementary
Essential Nonessential
QW 410
.1 φ Stringer/weave X
.7 φ Oscillation X
.9 φ Multiply to Single Pass/Side X X
.21 1 vs. 2 Sided Welding X
26 ± Peening X
4-151
QW-410Technique
.26 ± Peening X
.37 φ Single to Multiple Passes
![Page 152: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/152.jpg)
Module 4 – Welding Design Joint Design
Backstep
Welding Sequence
4-152
Block(Unwelded spaces filled after welding of intermittent blocks)
Cascade
![Page 153: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/153.jpg)
Module 4 – Welding Design Joint Design
StaggeredIntermittent
Special Purpose Welds
4-153
Boxing(End Return)
Fillet Weld
ChainIntermittentFillet Weld
![Page 154: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/154.jpg)
Module 4 – Welding Design Joint Design
Welding Position
F - Fillet weldG - Groove weld
1 - flat
1G 1F
2F
1G
4-154
2 - horizontal3 - vertical4 - overhead
2F 2G
3G 3F
4G 4F
2G
5G 6G
![Page 155: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/155.jpg)
Welding Symbols
Module 4E
![Page 156: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/156.jpg)
Module 4 – Welding Design Welding Symbols
Standard Location of Elements
Key ElementsArrowReference LineTailWeld SymbolsSupplementary
4-156
SymbolsOther Details
Only the REFERENCE LINE and ARROW are requiredReference line are always horizontalSymbol without L-P denotes continuous welds
![Page 157: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/157.jpg)
Module 4 – Welding Design Welding Symbols
Symbol Dimensions?
Tolerances, if required, are to be placed in tailWelding Symbols are usually drawn without dimension units such as inches or millimetersBut, Welding Symbols to be used for publications or those requiring high precision should be dimensioned and have the dimensional tolerances noted within the tail.
4-157
![Page 158: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/158.jpg)
Module 4 – Welding Design Welding Symbols
NOTE:
(1) The reference line is shown dashed for illustrative purposes.
(2) Symbols with a perpendicular leg shall have the perpendicular leg drawn
h l f id f h
Weld Symbols
4-158
on the left side of the symbol (fillet, bevel-, J-, or flare-bevel-groove)
Source: AWS A2.4:2007
![Page 159: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/159.jpg)
Module 4 – Welding Design Welding Symbols
Supplementary Symbols
4-159
Significance of arrowArrow side below reference lineOther side above reference line
![Page 160: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/160.jpg)
Module 4 – Welding Design Welding Symbols
Below reference line
Arrow and Other Side Convention – Examples
4-160
Above reference line
Both sides of reference line
Weld Cross Section Symbol
Weld Cross Section Symbol
Weld Cross Section Symbol
![Page 161: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/161.jpg)
Module 4 – Welding Design Welding Symbols
Break in Arrow of Welding Symbol – Examples
4-161
Weld Cross Section Symbol
Weld Cross Section Symbol
Weld Cross Section Symbol
![Page 162: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/162.jpg)
Module 4 – Welding Design Welding Symbols
Combined Weld Symbols
Combined Weld Symbols
4-162
Multiple Arrow Lines
![Page 163: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/163.jpg)
Module 4 – Welding Design Welding Symbols
S b l
Combined Weld Symbols – Examples
4-163
Weld Cross Section Symbol Weld Cross Section Symbol
Weld Cross Section
Weld Cross Section Symbol
![Page 164: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/164.jpg)
Module 4 – Welding Design Welding Symbols
Specification of Extent of Welding Use Multiple Arrows
4-164
Welds Symbols
Welds Symbols
![Page 165: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/165.jpg)
Module 4 – Welding Design Welding Symbols
Supplementary DataHidden Members of the Same as a Visible Member
TYPICALBOTH
PROCESSDATA
(CO STD)
2 ANGLES
Supplementary Information
4-165
ANGLES
Omission of Tail When No References are Required
![Page 166: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/166.jpg)
Module 4 – Welding Design Welding Symbols
Field Weld and All-Around Symbol
Flag indicated field weldCircle indicates that the is to continue along the entire joint length (i.e., weld all around)
4-166
![Page 167: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/167.jpg)
Module 4 – Welding Design Welding Symbols
Specification of Extent of Welding Using Weld All-Around Symbol
4-167
WELDS
SYMBOL
WELDS
SYMBOL
![Page 168: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/168.jpg)
Module 4 – Welding Design Welding Symbols
Extent of Welding Denoted by SymbolsUsing Weld All-Around Symbol
4-168
Weld Around a Shaft
Weld in Several Planes
![Page 169: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/169.jpg)
Module 4 – Welding Design Welding Symbols
SizeLength and
Pitch
WELDS
Location and Extent of Fillet Welds
4-169
Welds Approximately Located
Welds Definitely Located
SYMBOLS
![Page 170: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/170.jpg)
Module 4 – Welding Design Welding Symbols
ChainIntermittent
Welds
Length and Pitch of Intermittent Welds
4-170
Staggered Intermittent
Welds
SYMBOLWELDS
SYMBOLWELDS
![Page 171: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/171.jpg)
Module 4 – Welding Design Welding Symbols
Partially Filled Plug Weld
Dimensions of Plug and Slot Weld
4-171
Partially Filled Slot Weld
![Page 172: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/172.jpg)
Module 4 – Welding Design Welding Symbols
Melt-Through Symbol
4-172
![Page 173: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/173.jpg)
Module 4 – Welding Design Welding Symbols
Edge-Flange
Melt-Through with Flange Welds
4-173
Corner-Flange
![Page 174: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/174.jpg)
Module 4 – Welding Design Welding Symbols
Application of “Typical” Welding Symbols Using Tail
4-174
![Page 175: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/175.jpg)
Module 4 – Welding Design Welding Symbols
Specification of Extent of Welding Using Tail of the Welding Symbol
4-175
![Page 176: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/176.jpg)
Module 4 – Welding Design Welding Symbols
Weld Contours and Finishing of Welds
Specification of Completed Weld Using the Welding Symbol
The weld tail can specify the final contour of the weld as well as any addition processing steps require to achieve the contour
4-176
C – ChippingG – GrindingH – HammeringM – MachiningR – RollingU - Unspecified
Weld ContoursFlushFlat
ConvexConcave
![Page 177: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/177.jpg)
Module 4 – Welding Design Welding Symbols
Tail of the Welding Symbol
Supplementary Information
The weld tail can also include supplementary information important the welder/supervisor
Welding procedureAdditional/specific welding dimensions or tolerances
4-177
Welding Process Spec.
References
Designated Typical Situations
Details of Special Types of Welds
Weld Dimension Tolerance
![Page 178: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/178.jpg)
Module 4 – Welding Design Welding Symbols
Arrow side flush contour symbol
Flush and Convex Contour Symbols
4-178
Both sides convex contour symbol
Other side flush contour symbol
![Page 179: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/179.jpg)
Module 4 – Welding Design Welding Symbols
Standard Location of NDE Elements
4-179
![Page 180: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/180.jpg)
Module 4 – Welding Design Welding Symbols
Examination Method Letter Designations
Acoustic emission AETElectromagnetic ET
Standard Location of NDE Elements
The NDE Key elements are similar to the welding key elements
Reference LineArrowExamination Method Letter DesignationsExtent and Number of
4-180
Electromagnetic ETLeak LTMagnetic practical MTNeutron radiographic NRTPenetrant PTProof PRTRadiographic RTUltrasonic UTVisual VT
Extent and Number of ExaminationsSupplementary SymbolsTail (specifications, codes or other references)
![Page 181: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/181.jpg)
Module 4 – Welding Design Welding Symbols
Combined Welding and NDE Symbols
Welding and NDE symbols can be combined on the same reference line, or on separate multiple reference linesCombining welding and NDE symbols on multiple reference lines often clarifies the exact sequence of operations required
4-181
UT
![Page 182: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/182.jpg)
Module 4 – Welding Design Welding Symbols
MT
VT
RT
UTMTMT
PT
VT
ET RTLT+PRT
UT
NDE Locations
4-182
AET UT+RTPT
UT
Field Examination
Examine-All-Around
Welding & NDE SymbolsNDE Combinations
![Page 183: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/183.jpg)
Module 4 – Welding Design Welding Symbols
RT symbol, with angle of radiation
MT symbol, both sides for 6 inch length
Number of Examination
Specifications, Codes,and References
Examples of NDE Symbols
4-183
incidence
Partial Examination
and References
Length to be Examined
![Page 184: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/184.jpg)
Module 4 – Welding Design Welding Symbols
Plane AreasArea of Revolution
Examples of NDE Symbols
4-184
Acoustic Emission
Area of Revolution
![Page 185: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/185.jpg)
Welding Symbol Applications
![Page 186: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/186.jpg)
Module 4 – Welding Design Welding Symbols
Complete Joint Penetration with Optional Joint Geometry
4-186
![Page 187: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/187.jpg)
Module 4 – Welding Design Welding Symbols
Groove Weld Size & Depth of Bevel Not Specified
4-187
![Page 188: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/188.jpg)
Module 4 – Welding Design Welding Symbols
Specification of Groove Weld Size (E) Only
4-188
Double-V-groove weld with root opening
![Page 189: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/189.jpg)
Module 4 – Welding Design Welding Symbols
Groove Weld Size without Depth of Bevel Specified
4-189
![Page 190: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/190.jpg)
Module 4 – Welding Design Welding Symbols
Specification of Groove Weld Size (E) andDepth of Bevel (S)
4-190
![Page 191: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/191.jpg)
Module 4 – Welding Design Welding Symbols
Combined Groove and Fillet Welds
4-191
![Page 192: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/192.jpg)
Module 4 – Welding Design Welding Symbols
Root Opening of Groove Welds
4-192
![Page 193: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/193.jpg)
Module 4 – Welding Design Welding Symbols
Groove Angle of Groove Welds
4-193
Groove angle is placed just outside the weld symbol
![Page 194: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/194.jpg)
Module 4 – Welding Design Welding Symbols
Groove Angle of Groove Welds
4-194
![Page 195: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/195.jpg)
Module 4 – Welding Design Welding Symbols
Back Weld Symbol
Back or Backing Weld Symbol
4-195
Back Weld Symbol
Backing Weld Symbol
![Page 196: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/196.jpg)
Module 4 – Welding Design Welding Symbols
Single-V-Groove Weld with Backing
4-196
![Page 197: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/197.jpg)
Module 4 – Welding Design Welding Symbols
Joint with Welding Symbol
Application of the Consumable Insert Symbol
4-197
Joint Geometry with Insert in Place Joint with Root Pass Combined
![Page 198: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/198.jpg)
Module 4 – Welding Design Welding Symbols
Groove Welds with Back Gouging
4-198
![Page 199: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/199.jpg)
Module 4 – Welding Design Welding Symbols
Groove Welds with Back Gouging
4-199
![Page 200: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/200.jpg)
Module 4 – Welding Design Welding Symbols
Groove Welds with Back Gouging
4-200
![Page 201: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/201.jpg)
Module 4 – Welding Design Welding Symbols
Skewed T-Joint
4-201
![Page 202: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/202.jpg)
Module 4 – Welding Design Welding Symbols
Size of Fillet Welds
4-202
![Page 203: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/203.jpg)
Module 4 – Welding Design Welding Symbols
Length of Fillet Welds
4-203
![Page 204: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/204.jpg)
Module 4 – Welding Design Welding Symbols
Staggered Intermittent Fillet Welds
4-204
![Page 205: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/205.jpg)
Module 4 – Welding Design Welding Symbols
Chain Intermittent Fillet Welds
4-205
![Page 206: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/206.jpg)
Module 4 – Welding Design Welding Symbols
Applications of Stud Weld Symbols
4-206
![Page 207: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/207.jpg)
Module 4 – Welding Design Welding Symbols
Applications of Surfacing Weld Symbols
4-207
![Page 208: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/208.jpg)
Module 4 – Welding Design Welding Symbols
Multiple Layers
Applications of Surfacing Weld Symbols
4-208
![Page 209: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/209.jpg)
Mechanical Testing
Module 4F
![Page 210: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/210.jpg)
Module 4 – Welding Design Mechanical Testing
Mechanical Testing
There are several different sources for mechanical testing methods
AWS B4.0M:2000 “Standard Methods for Mechanical Testing of Welds”Several ASTM standards
There are several different sources for acceptance criteria i l di t ti d t d lifi ti
4-210
including construction documents and qualification documents
ASME Section IX “Welding and Brazing Qualification”AWS D1.1 “Structural Welding Code Steel”API 1104 “Welding of Pipelines and Related Facilities”
![Page 211: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/211.jpg)
Module 4 – Welding Design Mechanical Testing
Mechanical Testing
Testing Methods covered in this moduleHardness TestingTension TestBend TestFillet Weld Break TestFracture Toughness Test
4-211
![Page 212: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/212.jpg)
Module 4 – Welding Design Mechanical Testing
Hardness Testing
Hardness is shorthand for strengthCan characterize change in properties across a weldSeveral standard techniques
Rockwell (ASTM E-18)Brinell (ASTM E 10)Vickers (ASTM E92, E384)
Brinell
Knoop
4-212
( S 9 , 38 )Knoop (ASTM E384)
DifferencesIndentation load sequenceIndenter shapeProperty measured
Indentation depthIndentation area
Calculation of Hardness Value
Scales related to each other
Vickers
Rockwell120o angle & 0.2mm radius
![Page 213: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/213.jpg)
Module 4 – Welding Design Mechanical Testing
Macrohardness Test
4-213
Rockwell Test
Brinell Test
![Page 214: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/214.jpg)
Module 4 – Welding Design Mechanical Testing
Microhardness Test
Vickers
4-214
Knoop
![Page 215: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/215.jpg)
Module 4 – Welding Design Mechanical Testing
Hardness Tests, Indenters, and Shapes of Indention
Brinell Indentor
4-215Rockwell Indentor
![Page 216: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/216.jpg)
Module 4 – Welding Design Mechanical Testing
Comparison of Hardness Tests
4-216
Microhardness testing often used to characterize changes in strength across a weld and Heat Affected Zone
![Page 217: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/217.jpg)
Module 4 – Welding Design Mechanical Testing
Hardness Relationship to Mechanical Properties
Hardness can be used to estimate material strengthEstimated tensile strength of steel
510 * HB, HB<175490 * HB, HB>175
Estimated yield strength of steel
0 33* hardness
4-217
0.33 hardness(Vickers * 10/3 = Tensile yield)
HB = Brinell Hardness
![Page 218: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/218.jpg)
Module 4 – Welding Design Mechanical Testing
Hardness Scale Conversion
Rockwell C Brinell Vickers Tensile ksi
60 654 697
55 560 595 288
50 481 513 245
4-218
45 421 446 212
40 390 412 191
35 327 345 163
30 286 302 142
25 253 266 125
![Page 219: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/219.jpg)
Module 4 – Welding Design Mechanical Testing
Tension Test
Summary of MethodTension testing of welded joints is done by means of a calibrated testing machine and devices The test sample is pulled in tension until the sample fails
SignificanceTension test provides information on properties of welded joints: load b i iti j i t d i d d tilit
4-219
bearing capacities; joint design; and ductility
![Page 220: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/220.jpg)
Module 4 – Welding Design Mechanical Testing
Tension Test – Summary of Method
4-220
Test coupon in the loading grips
Initial Gauge Length
AreaSectionalCrossInitial
LoadStress
.... −=
LengthGaugeInitial
ElongationStrain
....=
![Page 221: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/221.jpg)
Module 4 – Welding Design Mechanical Testing
Stress-Strain Curve
Parallel to theoriginal slope line
4-221
0.2% offset Ductility
Area beneath the entire stress-strain curve up to fracture point
is called “TOUGHNESS”
“Modulus of Resilience”
![Page 222: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/222.jpg)
Module 4 – Welding Design Mechanical Testing
Tension Test Apparatus
4-222
Modern Loading System -Computer Controlled
Conventional Loading System –for Tensile Strength Only
![Page 223: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/223.jpg)
Module 4 – Welding Design Mechanical Testing
Tensile Test - Specimens
All Weld Metal Tensile TestDetermine weld metal ultimate tensile strength, yield strength, elongation and reduction in area
Reduced Section Tension Test (RST)Determine ultimate tensile strength only
S i h ll b t il t t d i
Gauge Length
4-223
Specimens shall be tensile tested in the as-welded condition unless the procedure qualification requires a PWHT
![Page 224: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/224.jpg)
Module 4 – Welding Design Mechanical Testing
Round Tension Specimen
Tensile Test - Procedure
Welding Procedure QualificationTension test specimen shall be ruptured under tensile loadTensile strength shall be computed by dividing the ultimate total load by the least cross-sectional area of the specimen as calculated from actual measurements made before the load is applied
4-224
⎟⎟⎠
⎞⎜⎜⎝
⎛=
4
..2D
LoadMaximumUTS
πUltimate Tensile Strength
Yield Strength at Specified Offset⎟⎟⎠
⎞⎜⎜⎝
⎛=
4
OffsetLoadYS
π
Percent ElongationLengthGaugeOriginal
LengthGaugeOriginalLengthGaugeLFinalf ....
........ −=ε
Reduced Section Tension Specimen
AreaSectionCrossOriginal
LoadMaximumUTS
....
..
−=Ultimate Tensile Strength
![Page 225: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/225.jpg)
Module 4 – Welding Design Mechanical Testing
ASME Section IX – QW-150 Tension Test
QW-151.1, Reduced Section – Plate
4-225
![Page 226: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/226.jpg)
Module 4 – Welding Design Mechanical Testing
ASME Section IX – QW-150 Tension Test
QW-151.2, Reduced Section – PipeFor pipe diameters greater than 3 in.
4-226
![Page 227: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/227.jpg)
Module 4 – Welding Design Mechanical Testing
ASME Section IX – QW-150 Tension Test
QW-151.2, Reduced Section – PipeFor pipe diameters less than or equal to 3 in.
4-227
![Page 228: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/228.jpg)
Module 4 – Welding Design Mechanical Testing
ASME Section IX – QW-150 Tension Test
QW-151.3, Turned Specimen
4-228
![Page 229: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/229.jpg)
Module 4 – Welding Design Mechanical Testing
ASME Section IX – QW-150 Tension Test
QW-151.4, Full-Section Specimens for PipeFor pipe diameters less than or equal to 3 in.
4-229
![Page 230: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/230.jpg)
Module 4 – Welding Design Mechanical Testing
Tensile Test – Acceptance Criterion
Reduced Section Tension per AWS D1.14.8.3.5 Acceptance Criteria for Reduced-Section Tension Test
The tensile strength shall be no less than the minimum of the specified tensile range of the base metal used
Reduced Section Tension per ASME Section IXQW-153 Acceptance Criteria – Tension Test
To pass the tension test the specimen shall have a tensile strength that is
4-230
To pass the tension test the specimen shall have a tensile strength that is not less than the minimum specified tensile strength of the base metal, ornot less than the minimum specified tensile strength of the weaker of the two materials if different strength materials are welded, ornot less than the minimum specified tensile strength of the weld metal when a weld metal having lower room temperature strength than the base metal is allowed, orif specimen breaks in base metal outside the weld or fusion line, the test shall be accepted, provided the strength is not more than 5% below the minimum specified tensile strength of the base metal
![Page 231: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/231.jpg)
Module 4 – Welding Design Mechanical Testing
Guided Bend Test
Summary of MethodThe specimens are guided in the bending process by a test fixture that employs a mandrel with wraparound roller or end supports with plungerThe maximum strain on the tension surface is controlled by the thickness of the specimen and the radius of the mandrel or plunger
Significance
4-231
SignificanceThe ductility of a welded joint
![Page 232: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/232.jpg)
Module 4 – Welding Design Mechanical Testing
Guided Bend
Bend Test Apparatus
4-232
![Page 233: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/233.jpg)
Module 4 – Welding Design Mechanical Testing
Side Bend Root Bend FaceBend
Guided Bend Test Specimens
4-233
Transverse Bend Test Specimens
Side Bend Face Bend
Longitudinal Bend Test Specimens
RootBend
![Page 234: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/234.jpg)
Module 4 – Welding Design Mechanical Testing
Guided Bend Test Procedure
Specimens shall be bent in jigsThe weld and HAZ shall be within the curved portion of the specimen if not the specimen shall be discarded Unless otherwise specified, the specimen shall be tested at ambient temperature and deformation shall occur in a time period between 15 seconds and 2 minutes
4-234
pAppropriate surface of the specimen, according to its type, shall be bent such that it is placed in tensionSpecimen shall be bent around the correct size mandrel (plunger) until the specimen is forced into the die until a 1/8” wire cannot be inserted between the specimen and die, or the specimen is bottom ejected if the roller type jig is usedWhen specimens wider than 1-1/2” are tested, mandrel must be at least 1/4” wider than specimen
![Page 235: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/235.jpg)
Module 4 – Welding Design Mechanical Testing
ASME Section IX – QW-160 Guided Bend Test
QW-161.1, Transverse Side Bend
4-235
![Page 236: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/236.jpg)
Module 4 – Welding Design Mechanical Testing
ASME Section IX – QW-160 Guided Bend Test
QW-161.2 and 161.3, Transverse Face or Root Bend
4-236
![Page 237: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/237.jpg)
Module 4 – Welding Design Mechanical Testing
ASME Section IX – QW-160 Guided Bend Test
QW-161.6 and 161.7, Longitudinal Face or Root BendUsed to test materials with markedly different bending properties
Largely different properties between different base materialsLargely different properties between the weld metal and base material
4-237
![Page 238: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/238.jpg)
Module 4 – Welding Design Mechanical Testing
ASME Section IX – QW-160 Guided Bend Test
QW-162.1, Bend Test Jigs
4-238
![Page 239: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/239.jpg)
Module 4 – Welding Design Mechanical Testing
ASME Section IX – QW-160 Guided Bend Test
QW-162.1, Bend Test Jigs
4-239
![Page 240: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/240.jpg)
Module 4 – Welding Design Mechanical Testing
ASME Section IX – QW-160 Guided Bend Test
The dimensions of the bend test jig depend on the material that is being bent
4-240
![Page 241: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/241.jpg)
Module 4 – Welding Design Mechanical Testing
Guided Bend Test – Acceptance Criterion
Bend Test per AWS D1.14.8.3.3 Acceptance Criteria for Bend Test
No discontinuities greater than 1/8” in any directionThe sum of all discontinuities greater than 1/32” but less than 1/8” should not exceed 3/8”No corner cracks greater than 1/4” with no visible evidence of slag or other fusion discontinuity
4-241
Corner CrackDiscontinuity
Bend Test per ASME Section IXQW-163 Acceptance Criteria – Bend Test
No discontinuities greater than 1/8” in any directionCorner cracks shall not be considered unless there is evidence of weld defect
![Page 242: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/242.jpg)
Module 4 – Welding Design Mechanical Testing
Fillet Weld Break Test
Summary of MethodOne leg of a T-joint is bent upon the other so as to place the root of the weld in tension.The load is maintained until the legs of the joint come into contact with each other or the joint fractures
Significance
4-242
SignificanceTo determine the soundness of fillet welded joints
![Page 243: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/243.jpg)
Module 4 – Welding Design Mechanical Testing
Fillet Weld Break Test Procedure
A force as shown or other forces causing the root of the weld to be in tension shall be applied to the specimenThe load shall be increased until the specimen fractures or bends flat upon itselfIf the specimen fractures, the fracture surfaces shall be examined visually to the criteria of the applicable standard
4-243
y pp
![Page 244: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/244.jpg)
Module 4 – Welding Design Mechanical Testing
ASME Section IX – QW-180 Fillet Weld Test
4-244
![Page 245: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/245.jpg)
Module 4 – Welding Design Mechanical Testing
ASME Section IX – QW-180 Fillet Weld Test
4-245
![Page 246: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/246.jpg)
Module 4 – Welding Design Mechanical Testing
Fillet Weld Break Test – Acceptance Criteria
Fillet Weld Break Test per AWS D1.14.30.4.1 Acceptance Criteria for Fillet Weld Break Test
Reasonably uniform appearance and free of overlap, cracks and undercut within acceptable limits of visual inspectionThe broken specimen shall be flat upon itself or the fracture surface shall show complete root fusion with no inclusion or porosity larger than 3/32” in greatest dimension
4-246
The sum of the greatest dimensions of all inclusions and porosity shall not exceed 3/8” in the 6” long specimen.
Fillet Weld Break Test per ASME Section IXQW-182 Fracture Test
The fracture surface shall show no evidence of cracks or incomplete root fusionThe sum of inclusions and porosity shall not exceed 3/8” or 10% of the section
![Page 247: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/247.jpg)
Module 4 – Welding Design Mechanical Testing
Fracture Toughness Tests – Summary of Methods
Charpy V-notch - Impact on V-notched specimenDynamic Tear - Three point bending of U-notched specimen loaded at high strain rate by strikePlane-Strain Fracture Toughness - Plane-strain critical fracture toughness value obtained at slow loading rates on compact tension specimen with maximum constraint (thick
4-247
p p (specimen with deep crack) resulting in brittle fracture with little or no deformationDrop-Weight Nil Ductility Transition Temperature – Drop weight impact on flat notched specimen with maximum fracture stress at material’s yield stress
![Page 248: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/248.jpg)
Module 4 – Welding Design Mechanical Testing
Fracture Toughness Test – Significance
Provides a measure of resistance to crack initiation or propagation or bothThe same welding process, procedure, and weld cooling rates must be used for the test sample and the structureFracture toughness of steels is sensitive to service temperature
4-248
Shear Deformation
Shear Rupture DimplesPhotograph of Typical Brittle Fracture Surface
Shear Lip
Shear Lip
Chevron Markings
Chevron Markings
p
![Page 249: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/249.jpg)
Module 4 – Welding Design Mechanical Testing
Clip Gage
CMOD
Crack Tip
Fracture Toughness Test Apparatus
4-249Four-Point Bending Test
Compact Tension TestCharpy V-Notch Test (right: placement of specimen in anvil)
wa4W
Clip Gage
Three-Point Bending Test
![Page 250: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/250.jpg)
Module 4 – Welding Design Mechanical Testing
Fracture Toughness Test Specimens
4-250
Charpy V-Notch Impact Specimen
Dynamic Tear Test Specimen
![Page 251: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/251.jpg)
Module 4 – Welding Design Mechanical Testing
factorcorrectionaKI ..•= πσ
Crack Driving Force: Stress Intensity Factor, KI
Fracture Toughness Test Specimens
4-251
Drop Weight Nil-Ductility Temperature Test Specimen
Compact Tension Fracture Toughness Test Specimen
![Page 252: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/252.jpg)
Module 4 – Welding Design Mechanical Testing
Fracture Toughness Test Apparatus
4-252
Drop-Weight Nil Ductility Transition Temperature Test
3O~5O
![Page 253: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/253.jpg)
Module 4 – Welding Design Mechanical Testing
Fracture Toughness Test Procedure
4-253
Orientation of Weld Metal Fracture Toughness Specimen in a Double-Groove Weld Thick Section Weldment
![Page 254: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/254.jpg)
Module 4 – Welding Design Mechanical Testing
y (f
t-lb
)Fracture Toughness Test Acceptance Criteria
4-254
Low temperature
Hightemperature
Charpy V-Notch Test Results
Test Temperature
Cha
rpy
Ene
rgy
![Page 255: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/255.jpg)
Module 4 – Welding Design Mechanical Testing
Fracture Toughness Test Acceptance Criteria
4-255
Dynamic Tear Test Results
![Page 256: 1501 - E118 - Welding Technology and Codes - 04 - Welding](https://reader030.vdocuments.net/reader030/viewer/2022012409/616a451511a7b741a350ab12/html5/thumbnails/256.jpg)
Module 4 – Welding Design Mechanical Testing
Fracture Toughness KIC – ASTM A572 Steel
Fracture Toughness Test Acceptance Criteria
4-256Compact Tension Test Results