Two Panel Sequential LED Tail Light Kit Installation Guide

1972-74 PLMOUTH ‘CUDA

Please refer to webiste for full warranty information. DIGI-TAILS is not a licensed GM product.

Kit Contents: • 2 LED panels • 2 Rubber grommets • 1 Power wire • 1 Pigtail harness kits • 1 Crimp terminal kit

PN

12

00

37

2

1972-74 PLYMOUTH ‘CUDA LED PANEL INSTALLATION

LED PANEL INSTALLATION

1. Cut off the power to your car.

Open the hood of your car. Disconnect the negative terminal from the battery, which will cut off the power in your car. To verify that the power is disconnected, press the brake pedal; your brake lights should not turn on.

2. Remove the current tail lights.

Turn the light sockets counter-clockwise to remove them from the tail light housings. As a safety precaution, remove the bulbs from the sockets. Put them aside since they will no longer be needed. Remove the tail light housing assembly from the car.

3.

Each LED panel is marked Driver Side and Passenger Side on the backside of the LED panel, which identifies where each respective LED panel is to be mounted.

2

The LED boards are shipped with the slide switch set to Sequential mode. We recommend that all slide switches be set to the same setting (either standard or sequential).

Please follow all local laws concerning exterior lighting.

Note

Shown in sequential mode

SEQUENTIALPOSITION

STANDARDPOSITION

Position the LED panels.

You may begin with the LED panel installation, however, you will need to complete the wiring modifications before the LED panels and housings are paired as one. Read over the entire instruction guide to determine the method that works best for you.

Hint

The Driver Side LED panel is shown above.

1972-74 PLYMOUTH ‘CUDA LED PANEL INSTALLATION 3

4.

Carefully separate the lens from the tail light housing. There is a weak glue holding the two together. They can be pried apart with patience and care.

Attach mounting brackets.

5.

Feed the extension harness through the socket hole and plug them onto the LED panels. Using these extension harnesses allows for easy removal of the tail light assembly in the future if needed.

Plug in extension harnesses.

Take your time and care when separating the lens from the housing.

Note

Separate

6.

The LED panel assembly is meant to sit inside of the housing. To keep from making any permanent changes to the housing, use silicone to fasten the LED panel into place. Besure to align the LED panel and the housing so they are both upright.

Mount the LED panels.

Attach LED panel with siliconeat the blue dot locations.

1972-74 PLMOUTH ‘CUDA WIRE SPLICING INSTALLATION

WIRE SPLICING INSTALLATION

1. Find and access the tail light wires.

tail light housing assembly and remove the cloth tape to expose the taillight wires.

2. Splice the LED panel wires into the original wires.

3. Connect all the ground wires.

Connect all the ground wires together. Bolt them to the trunk latch support along with the original rear body harness ground. The ground connection must be good in order to the operate the LED tail lights.

4. Splice the Orange constant power wire into the T-Tap and the LED panel Orange wire.

An Orange power wire is supplied along with a T-Tap. The orange power wire must be supplied with a constant 12 volt battery supply for the LED circuitry to operate properly. The T-Tap connector is used to splice to the constant power source, like the dome light wire.

Spice the T-Tap connector into the constant power wire, then plug the orange wire into the T-Tap. The other end of the orange wire is spliced into the LED panel Orange wires.

!

Wire splicing installation

Pick a point in the rear body harness between the driver’s side quarter panel andthe driver’s side tail light housing assembly and remove the cloth tape to

Take the LED harness DARK GREEN wires and splice it with the original

Take the LED harness BROWN wires and splice it with the original

The light socket ends on the car harness are no longer needed.

Take the LED harness YELLOW wires and splice them in with the original light wires. The ends going to the side marker lights must be included in the splice for the side markers to remain functional.

Take the ground wires and connect them all together. Bolt them to the trunk latch support along with the original rear body harness ground.

Note: A good ground connection is essential to the operation of the LED tail lights.

An ORANGE power wire is supplied along with a T-Tap. The orange power wire must be supplied with a constant 12 volt battery supply for the LED circuitry to operate properly. The T-Tap connector is used to splice to the constant power source, like the dome light wire.

Spice the T-Tap connector into the constant power wire, then plug the orange wire intothe T-Tap. The other end of the orange wire is spliced into the LED harness Orange wires. The last page is a wire diagram of how the LED harness splices into the car’s original harness.

Insert wire onto T-Tap Crimp with pliers

Wires spliced together. Fold wires over to a side.

To keep the wires neatly tucked and in line, take the spliced sections and foldthem over to one side and tape them in place. This will allow you to place thewiring into loom or have the ability to wrap the LED harness wiring tightly away.

Wire splicing installation

Pick a point in the rear body harness between the driver’s side quarter panel andthe driver’s side tail light housing assembly and remove the cloth tape to expose the tail light wires.

Take the LED harness DARK GREEN wires and splice it with the original DARK

Take the LED harness BROWN wires and splice it with the original BROWN

The light socket ends on the car harness are no longer needed.

Take the LED harness YELLOW wires and splice them in with the original light wires. The ends going to the side marker lights must be included in the splice for the side markers to remain functional.

Take the ground wires and connect them all together. Bolt them to the trunk latch support along with the original rear body harness ground.

Note: A good ground connection is essential to the operation of the LED tail lights.

An ORANGE power wire is supplied along with a T-Tap. The orange power wire must be supplied with a constant 12 volt battery supply for the LED circuitry to operate properly. The T-Tap connector is used to splice to the constant power source, like the dome light wire.

Spice the T-Tap connector into the constant power wire, then plug the orange wire intothe T-Tap. The other end of the orange wire is spliced into the LED harness Orange wires. The last page is a wire diagram of how the LED harness splices into the car’s original harness.

Insert wire onto T-Tap Crimp with pliersPlug connector

To keep the wires neatly tucked and in line, take the spliced sections and foldthem over to one side and tape them in place. This will allow you to place thewiring into loom or have the ability to wrap the LED harness wiring tightly away.

1. Insert wire onto T-Tap

2. Crimp with pliers

3. Plug connector into T-Tap

original harness is on the last page.

Note

4

LED PanelLED Panel OriginalOriginal Notes

Dark Green Dark Green

Brown Brown The light socket ends on the car harness can be discarded.

Yellow BlackThe ends going to the side marker lights must be included in the splice for the side markers to remain functional.

1972-74 PLMOUTH ‘CUDA WIRE SPLICING INSTALLATION

5. Tuck and secure the spliced wires.

Take the spliced sections and fold them over to one side and tape them in place. This will allow you to place the wiring into loom or wrap the LED panel wiring tightly away.

!

Insert wire onto T-Tap Crimp with pliersPlug connector

into T-Tap

Wires spliced together. Fold wires over to a side. Wrap with tape to hold in place.

To keep the wires neatly tucked and in line, take the spliced sections and fold

wiring into loom or have the ability to wrap the LED harness wiring tightly away.

!

Spice the T-Tap connector into the constant power wire, then plug the orange wire intothe T-Tap. The other end of the orange wire is spliced into the LED harness Orange wires. The last page is a wire diagram of how the LED harness splices into the car’s original harness.

Insert wire onto T-Tap Crimp with pliersPlug connector

into T-Tap

Wires spliced together. Fold wires over to a side. Wrap with tape to hold in place.

To keep the wires neatly tucked and in line, take the spliced sections and foldthem over to one side and tape them in place. This will allow you to place thewiring into loom or have the ability to wrap the LED harness wiring tightly away.

1. Fold wires to one side.

2. Secure withelectrical tape.

7. Place the grommet around the wires and replace the lens.

Place the grommet around the panel wires and press it into the light socket hole. Test the lights to ensure correct function, then place the lens back onto the housing.

!

no-load

asher (PN 200002)

Black wire must be grounded

After all wire connections have been made feed the harness connector throughthe light hole socket and plug into the LED panel. Remove the lm from thedouble sided tape and place the LED panels into their nal position.

Place the grommet around the harness wires and press the grommet into thelight socket hole. Test the lights for correct function and replace the lens back

onto the housing.

5

The LED light kits are designed for best performance when

from DIGI-TAILS.

The black wire must be grounded

Note

1972-74 PLMOUTH ‘CUDA WIRE SPLICING INSTALLATION 6

PAS

SE

NG

ER

SID

E

TUR

N S

IGN

AL

DR

IVE

R S

IDE

TUR

N S

IGN

AL

ORIGINALREAR BODYHARNESS

RU

NN

ING

LIGH

TS

POWER CONNECTION

CONSTANT FUSED POWER SOURCE.(AT DOME LIGHT OR FUSE PANEL)

ALTHOUGH CLOSED END CONNECTORS ARE INCLUDED, IT IS RECOMMENDED THAT ALL SPLICED WIRES BE SOLDERED TOGETHER FOR BEST CONNECTION RELIABILITY.

STOCK SIDE MARKER

GROUND

GROUND

Note

GROUND

DRIVER SIDE LED PANEL PASSENGER SIDE LED PANEL

STOCK SIDE MARKER