2. jar 25 distances
TRANSCRIPT
![Page 1: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/1.jpg)
2. DISTANCES2. DISTANCES
Performance JAR 25Performance JAR 25
![Page 2: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/2.jpg)
DISTANCESDISTANCES
Screen height
Definitions
Declared distances
Required distances
Balanced field length
Unbalanced field length
![Page 3: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/3.jpg)
SCREEN HEIGHTSCREEN HEIGHT
Screen height is different depending on the type of aeroplane:
JAR 23: 50 ft
JAR 25: 35 ft
JAR 25 (WET RUNWAY): 15 ft
35 ft
JAR 25 Screen height
![Page 4: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/4.jpg)
DEFINITIONSDEFINITIONS
RUNWAY: Defined rectangular area on a land airport that is prepared for the landing and takeoff run of aircraft along its length.
STOPWAY: An area beyond the takeoff runway that is at least as wide as the runway, is centred upon the extended runway centreline, and is able to support an airplane during an aborted takeoff without causing structural damage to the airplane.
Stopway must not be used for landing calculations.
![Page 5: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/5.jpg)
DEFINITIONSDEFINITIONS
CLEARWAY: An area beyond the takeoff runway that is under the control of airport authorities where terrain or fixed obstacles may not extend above specified limits. It is not required to be able to support the weight of the aeroplane, it must only be free of obstacles.
min 250 ft
α = 1.25º26 inches
![Page 6: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/6.jpg)
DEFINITIONSDEFINITIONS
500 ft
α = 1.25º
![Page 7: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/7.jpg)
DECLARED DISTANCESDECLARED DISTANCES
Field lengths available for takeoff and landing are known as declared distances:
TORA: Takeoff Run Available
TODA: Takeoff Distance Available. (TORA + CWY)
ASDA: Accelerate-Stop Distance Available. (TORA + SWY)
LDA: Landing Distance Available. (TORA – DT)
![Page 8: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/8.jpg)
DECLARED DISTANCESDECLARED DISTANCES
RWY
CWY
SWYDT
TORA
ASDA
TODA
LDA
![Page 9: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/9.jpg)
TORATORA
TORA: The length of runway which is declared available by the appropriate authority and suitable for the ground run of an aeroplane taking off.
TORA is equal to the distance from the threshold to the Departure End of Runway (DER).
![Page 10: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/10.jpg)
TORATORA
TORA
![Page 11: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/11.jpg)
TODATODA
TODA: The length of the takeoff run available plus the length of the clearway available.
The maximum length of the clearway is half the TORA.
TORA CWY (1/2 TORA MAX)
TODA
![Page 12: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/12.jpg)
ASDAASDA
ASDA: The length of the takeoff run available plus the length of the stopway, if such stopway is declared available by the appropriate authority and is capable of bearing the mass of the aeroplane under the prevailing operating conditions.
TORA SWY
ASDA
![Page 13: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/13.jpg)
DECLARED DISTANCESDECLARED DISTANCES
According to JAR-OPS 1.490, “[…] an operator must take account of the loss, if any, of runway length due to alignment of the aeroplane prior to takeoff.”
Line-up corrections should be made when computing takeoff performance, anytime runway access does not permit positioning the airplane at the threshold.
![Page 14: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/14.jpg)
DECLARED DISTANCESDECLARED DISTANCES
Effective ASDA
Effective TODA
Runway length
A B
A: Adjustment to takeoff distance
B: Adjustment to accelerate-stop distance
![Page 15: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/15.jpg)
DECLARED DISTANCESDECLARED DISTANCES
There are different corrections based on 90º turns and 180º turns.
180º turn
![Page 16: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/16.jpg)
DECLARED DISTANCESDECLARED DISTANCES
![Page 17: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/17.jpg)
DECLARED DISTANCESDECLARED DISTANCES
![Page 18: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/18.jpg)
DECLARED DISTANCESDECLARED DISTANCES
The line-up distance will increase if the runway is not wide enough.
![Page 19: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/19.jpg)
DECLARED DISTANCESDECLARED DISTANCES
Depending on the length of the stopway and/or the clearway (if available), ASDA may be equal, longer or shorter than TODA.
![Page 20: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/20.jpg)
DECLARED DISTANCESDECLARED DISTANCES
![Page 21: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/21.jpg)
DECLARED DISTANCESDECLARED DISTANCES
Declared distances can be found in the AIP, although they are included in the charts.
![Page 22: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/22.jpg)
REQUIRED DISTANCESREQUIRED DISTANCES
Field lengths required for takeoff are:
TORR: Takeoff Run Required
TODR: Takeoff Distance Required.
ASDR: Accelerate-Stop Distance Required.
![Page 23: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/23.jpg)
TORRTORR
Takeoff Run Required is the longest of:
a) The distance from start of ground roll to a point halfway between the lift-off point and the point at 35 ft, assuming that the critical engine has failed at Vef.
b) 115% of the distance from start of ground roll to a point halfway between the lift-off point and the point at 35 ft, with all the engines running.
Therefore, the TOR will be only limitative when using a clearway.
The maximum usable clearway is then half the distance between the lift-off point and the point at 35 ft.
![Page 24: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/24.jpg)
TORRTORR
![Page 25: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/25.jpg)
TORRTORR
![Page 26: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/26.jpg)
ASDRASDR
Accelerate-stop Distance Required is the longest of:
a) The distance taken to accelerate to Vef, continue accelerating to V1 with one engine inoperative, accelerate for 2 more seconds, and come to a full stop.
b) The distance taken to accelerate to V1, accelerate for 2 more seconds, and come to a full stop. (With all engines operating)
Reverse thrust is NOT taken into account.
The most effective braking sequence is: brakes, thrust idle, spoilers.
![Page 27: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/27.jpg)
ASDRASDR
![Page 28: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/28.jpg)
TODRTODR
Takeoff Distance Required is the longest of:
a) The distance from the start of ground roll to the point where the aeroplane reaches a height of 35 ft and the V2 speed with engine failure having occurred at Vef.
b) 115% of the distance between start of ground roll and the point where the aeroplane reaches a height of 35 ft and the V2 speed with all engines operating.
Distance “a)” will be usually longer with twin-engine aeroplanes.
![Page 29: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/29.jpg)
TODRTODR
![Page 30: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/30.jpg)
CONSIDERATIONSCONSIDERATIONS
If V1 is reduced ASD will decrease and TOD will increase, and vice versa.
In general terms, acceleration is more affected than braking when the same condition affects both of them (for instance, runway slope).
![Page 31: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/31.jpg)
BALANCED FIELD LENGHTBALANCED FIELD LENGHT
If the V1 is calculated in such a way that both the ASDR and the TODR are of equal length, the takeoff is said to be a balanced field length takeoff. This situation is given when neither stopway nor clearway exist, or if both are available.
In that case the V1 is known as balanced V1.
TOD = ASD
35 ftBalanced V1
![Page 32: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/32.jpg)
BALANCED FIELD LENGHTBALANCED FIELD LENGHT
V1
m
TODRASDR
V1 BALANCED
![Page 33: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/33.jpg)
BALANCED FIELD LENGHTBALANCED FIELD LENGHT
V1
m
TODRASDR
V1 increases with weight
100.000 Kg
120.000 Kg
![Page 34: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/34.jpg)
UNBALANCED FIELD LENGTHUNBALANCED FIELD LENGTH
If the TORA is not enough to takeoff with our ATOW and a stopway or a clearway is available, we can take advantage of them, changing the balanced V1 value.
Thus, ASDR <> TODR, but the situation will meet the requirements because of that clearway or stopway.
Even with enough TORA, we may operate with unbalanced V1 if the balanced V1 is below the Vmcg or if it is above Vmbe.
![Page 35: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/35.jpg)
UNBALANCED FIELD LENGTHUNBALANCED FIELD LENGTH
CLEARWAY AVAILABLE (NO STOPWAY)
If we decrease the balanced V1 value, the ASDR will decrease and the TODR will increase.
In this case TODR > ASDR, and ASDR = ASDA = TORA.
TORA = ASDA = ASDR CWY
TODR
V1 < Balanced V1
35 ft
![Page 36: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/36.jpg)
UNBALANCED FIELD LENGTHUNBALANCED FIELD LENGTH
STOPWAY AVAILABLE (NO CLEARWAY)
If we increase the balanced V1 value, the ASDR will increase and the TODR will decrease.
In this case ASDR > TODR, and TODR = TODA = TORA.
TORA = TODA = TODR SWY
ASDR
V1 > Balanced V1
35 ft
![Page 37: 2. jar 25 distances](https://reader034.vdocuments.net/reader034/viewer/2022052509/55d25c09bb61ebb9698b45dd/html5/thumbnails/37.jpg)
UNBALANCED FIELD LENGTHUNBALANCED FIELD LENGTH
We have seen how changing the value of V1 we can increase our OTOW, if a clearway or a stopway is available.
But if BOTH of them are available, then we can operate with a balanced V1, since both ASDA and TODA are increased with those clearway and stopway.