INSTALLATION INSTRUCTIONS FOR PART 95-5026

1-800-221-0932 www.metraonline.com© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION

KIT FEATURES

• Double DIN head unit provision• Stacked ISO DIN head unit provision

A) DDIN Trim Plate | B) DDIN Brackets | C) Rear Support Bracket

KIT COMPONENTS

TOOLS REQUIRED:

95-5026

A B

APPLICATIONS2001-2004 Ford Mustang

2003-2006 Ford Expedition 2002-2005 Ford Explorer

2003-2006 Lincoln Navigator2002-2005 Lincoln Aviator

2002-2005 Mercury Mountaineer

Phillips Screwdriver I Socket wrench

C

TABLE OF CONTENTS

95-5026

Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

95-5026

1

Disconnect the negative battery terminal to prevent an accidentalshort circuit.

1

Unclip and remove shift lever trimpanel. (Figure A)

2

2001-2004 FORD MUSTANG

Unclip and remove the entire panelsurrounding the radio and climatecontrols including the vents.(Figure B)

3

Remove (2) 9/32” screws securingradio. (Figure B)

4

DASH DISASSEMBLY

A

B

95-5026

2

Disconnect the negative battery terminal to prevent an accidentalshort circuit.

1

Remove (2) 9/32” screws from aboveinstrument cluster. (Figure A)

2

2003-2006 FORD EXPEDITION

Unclip and remove entire panel sur-rounding radio, climate controls, andinstrument cluster. (Figure B)

3

Remove (2) 9/32” screws securingradio.

4

DASH DISASSEMBLY

A

B

95-5026

3

Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

1

Unclip and remove entire panel sur-rounding radio including climate con-trols and vents. (Figure A)

2

2002-2005 FORD EXPLORER2002-2005 MERCURY MOUNTAINEER

Remove (2) 9/32” screws securingradio. (Figure B)

3

DASH DISASSEMBLY

B

A

4

95-5026

Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

1

Open center console and remove (1)push pin from back of power windowswitch panel. (Figure A)

2

2003-2006 LINCOLN NAVIGATOR

Unclip and remove panel. 3

Remove (2) 9/32” screws exposedon shifter panel then unclip andmove shifter panel off to side.(Figure B,C)

4

Remove (2) 9/32” screws exposedunder ashtray assembly. (Figure C)

5

Unclip and remove entire panel sur-rounding climate controls and radio.

6

Remove (2) 9/32” screws securingradio. (Figure C)

7

DASH DISASSEMBLY

INSIDE CENTER CONSOLE TOP VIEW

TOP OF SHIFTER TRIM PANEL

5

4

7

7

A

B

C

5

95-5026 DASH DISASSEMBLY

Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

1

Unclip and remove vent panel aboveradio on top of dashboard. (Figure A)

2

2003-2005 LINCOLN AVIATOR

Remove (2) 9/32” screws exposedunder panel removed in step 1.(Figure B)

3

Unclip and remove panel aroundradio with door in it. (Figure C)

4

Unclip and remove vents belowradio. Figure D)

5

Remove (2) 9/32” screws securingradio. (Figure E)

6

A

B

C

D

105.9

E

95-5026 KIT ASSEMBLY

6

2

A

Slide the DDIN radio unit into thetrim plate bracket assembly andsecure the unit to the kit using thescrews supplied with the head unit.(Figure B)

3 Position the rear support bracketwith slide grooves facing down andsecure to the back of the aftermar-ket radio with the hardware suppliedwith aftermarket head unit.(Figure C)

Slide the appropriate bracket intothe trim plate aligning the holes inthe trim plate to the clips on thebracket. (Figure A)

1

B

C

DOUBLE DIN HEAD UNIT PROVISION

95-5026 KIT ASSEMBLY

7

2

A

Slide the stacked ISO DIN units intothe trim plate bracket assembly andsecure the units to the kit using thescrews supplied with the head units.(Figure B)

3 Position the rear support bracketwith slide grooves facing down andsecure to the back of the aftermar-ket radio with the hardware suppliedwith aftermarket head unit.(Figure C)

Slide the appropriate bracket intothe trim plate aligning the holes inthe trim plate to the clips on thebracket. (Figure A)

1

B

B

STACKED ISO DIN HEAD UNIT PROVISION

95-5026 FINAL ASSEMBLY

8

FINAL ASSEMBLY1 Locate the factory wiring harness in the dash and make the connection as shown.

Metra recomends using the proper mating adapter and making the connections asshown. (Isolate and individually tape off the ends of any unused wires to preventelectrical short circuit.)

2 Re-connect the negative battery terminal and test the unit for proper operation.3 Reassemble radio and dash assemblies in reverse order of disassembly.

A

A) Strip wire ends back 1/2"

B) Twist ends together

C) Solder

D) Tape

B

C

D

Make wiring connections using the EIA color code chart shown below and the instructions included with the headunit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individuallytape off ends of any unused wires to prevent electrical short circuit.

12V Ignition / Acc . . . Red

12V Batt / Memory . . Yellow

Ground . . . . . . . . . . . Black*

Power Antenna . . . . . Blue

Amp Turn-On . . . . . . Blue / White

Amp Ground . . . . . . . Black / White

Illumination. . . . . . . . Orange

Dimmer . . . . . . . . . . Orange / White

Right Front (+) . . . . . Gray

Right Front (-) . . . . . . Gray / Black

Left Front (+) . . . . . . White

Left Front (-) . . . . . . . White / Black

Right Rear (+). . . . . . Violet

Right Rear (-) . . . . . . Violet / Black

Left Rear (+). . . . . . . Green

Left Rear (-) . . . . . . . Green / Black

*NOTE: When Black a wire is not present, ground radio to vehicle chassis.All colors may not be present on all leads due to manufacturer’s specifications.

METRA / EIA WIRING CODE

FINAL WIRING CONNECTIONS

9

95-5026

NOTES

95-5026 INSTRUCTIONS

1-800-221-0932 www.metraonline.com© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST95-5026REV. 01/25/06