2003 fm scat

Q

14L-0015

ISO 9001:2000®

Page II

Page III

AAlligator Grab ...................................................... 2

Anti-Blow Up Tool .............................................. 2

BBailers

Dump Bailer ................................................... 5

Hydrostatic Bailer ........................................... 4

Sample Bailer ................................................. 5

Sand Bailer ..................................................... 3

Blind Box............................................................. 6

Broaching Tool (Tubing Broach) ......................... 58

Bull Dog Spear .................................................... 28

CCenter Spear ........................................................ 60

Centralizers

Steel ................................................................ 7

Teflon .............................................................. 7

Adjustable Bow Spring

Centralizer .................................................. 7

Check Set Tool “FMS” ........................................ 8

Circulating Plugs

Type A............................................................. 9

Type W............................................................ 9

EEqualizing Subs

Type B ............................................................. 10

Type H ............................................................ 10

Type FMSX .................................................... 23

Type FMSR..................................................... 23

F Flanges

Wellhead Flange Adapter ................................ 61

GGas Lift Equipment

BK-2 Latch ..................................................... 11

R Latch ........................................................... 11

RA Latch ......................................................... 11

RK Latch ........................................................ 11

DK Dummy Valve .......................................... 11

Gauge Ring (Paraffin Cutter) .............................. 12

Go Devil .............................................................. 13

PageHHydraulic Wireline Jar ......................................... 62

IImpression Blocks ............................................... 14

JJars

Spang Type Jars .............................................. 15

Tubular Jars .................................................... 16

KKickover Tools

Type AK .......................................................... 17

Type K ............................................................ 17

Type L ............................................................. 18

Type R ............................................................. 19

Type OK-1 ...................................................... 20

Type OM-1 ..................................................... 20

Knuckle Jars ........................................................ 21

Knuckle Joints ..................................................... 21

LLocking Mandrels

Type D Collar Lock Mandrel .......................... 25

Type W Locking Mandrel ............................... 25

FMSS Locking Mandrel ................................. 24

FMSX Locking Mandrel ................................ 22

FMSR Locking Mandrel ................................. 22

Lubricator Section ............................................... 26

MMagnets

Magnetic Fishing Tool .................................... 27

Skirted Magnet ............................................... 27

NNo Go Subs .......................................................... 24

OFMS Overshot ..................................................... 28

Table of Contents

Page

Page IV

PPackoff

Type G Packoff ............................................... 29

Paraffin Scratcher ................................................ 30

Plugs

D Plug ............................................................. 31

PS Plug ........................................................... 31

PN Plug ........................................................... 31

FMSPX Plug ................................................... 32

FMSPR Plug ................................................... 32

FMSXX Plug .................................................. 33

FMSRR Plug .................................................. 33

Pulling Tools

GG Pulling Tool .............................................. 34

GS Pulling Tool .............................................. 35

GR Adapter ..................................................... 35

JD Pulling Tool ............................................... 36

JU Pulling Tool ............................................... 37

PRS Pulling Tool ............................................ 40

R Pulling Tool ................................................. 38

S Pulling Tool ................................................. 39

QQuick Lock .......................................................... 40

Quick Union ........................................................ 41

RRope Sockets

Single Strand Rope Socket ............................. 42

Brass Wedge Rope Socket .............................. 42

Multi Strand Rope Socket .............................. 42

Running Tools ...................................................... 43

C-1 Running Tool ........................................... 44

D Running Tool .............................................. 45

D Running Tool (Collet Type) ........................ 45

G Stop Running Tool ...................................... 46

J Running Tool ................................................ 46

PS Running Tool ............................................. 47

W Running Tool .............................................. 47

FMSX Running Tool ...................................... 48

FMSR Running Tool ...................................... 48

SShifting Tools

B Shifting Tool ............................................... 49

FMSX Selective Shifting Tool ....................... 49

Standing Valves

Type A Standing Valve .................................... 50

FMSS Lock Standing Valve ........................... 50

Stems

Stem (Weight Bar) .......................................... 51

Lead Filled Stem............................................. 52

Roller Stem ..................................................... 52

Stops

Type A Tubing Stop ........................................ 53

Type G Tubing Stop ........................................ 53

Collar Stops ......................................................... 54

Stuffing Box ........................................................ 55

Hydraulic Packing Nut ................................... 55

TTest Tools

N Test Tool ...................................................... 56

S Test Tool ...................................................... 56

Tubing End Locator ............................................. 57

Tubing Swedge .................................................... 57

Tubing Broach

Diamond Broach ............................................. 58

Pineapple Broach ............................................ 58

Tree Connection................................................... 61

WWire Finders ........................................................ 59

Wireline Grabs ..................................................... 60

Table of Contents

Page Page

WIRELINE TOOL STRING

The Wireline Tool String is an assembly of wireline tools connected to the wireline

(slickline) for setting, pulling, or servicing downhole equipment. An assembly of

wireline tools is used to deliver surface controlled impacts (jar action) to manipu-

late devices within the well bore.

A standard set of wireline tools typically consists of:

• Wireline Socket (rope socket) provides a means for connecting the wireline

to the tool string.

• Wireline Stem (sinker bar) is used as weight to overcome well pressure,

fluids, and friction to sink the tools into the well bore. Stem is also used to

transmit force either upward or downward to set or retrieve downhole

controls.

• Wireline Knuckle Joint is used for flexibility through the tool string.

• Wireline Jars (spang type link jars) used for obtaining a hammering effect

by upward or downward movement.

• Wireline running tool, pulling tool, or other service tool required to per-

form services desired.

• Tool strings are available in various sizes that are designed by nominal

dimensions rather than tubing sizes.

WIRELINE TOOLSTRING SIZE – O.D.

THREAD CONNECTION PIN X BOX

FISHING NECK SIZE

1”� 5/8” – 11 NC 1.000”� 1 1/4”� 15/16” – 10 UN 1 3/16”� 1 1/2”� 15/16” – 10 UN 1 3/8”� 1 3/4”� 1 1/16” – 10 UN 1 3/4”� 2 1/8’� 1 1/6” – 10 UN 1 3/4”�

OTHER SIZES AVAILABLE ON REQUEST

TOOL STRING

ANTI-BLOW UP TOOL

ALLIGATOR GRAB

The Alligator Grab is a wireline fish-

ing tool used to catch and retrieve

objects from within the well bore.

The Alligator Grab is designed so that

the amount of jaw pressure required

is adjustable simply by adjusting the

spring tension of the tool prior to use.

ANTI-BLOW UP TOOL

The FMS Anti-Blow up Tool is used

to prevent the tool string from being

blown up the tubing during flowing

bottom hole pressure surveys.

ALLIGATOR GRAB

ANTI-BLOW UP TOOLSIZE PART NUMBER1 1/4” O.D. 1050-125-00

ANTI-BLOW UP TOOL

SAND BAILER

The FMS Bailer is a wireline service tool used to remove sand, mud, salt, or small

pieces of junk from the tubing or casing. The Sand Bailer is also used to clear

debris which has settled on top of sub-surface equipment, preventing the recov-

ery of the equipment by regular wireline operations.

The Sand Bailer is a pump-type tool which operates on the principle of a conven-

tional lift pump with piston.

The Sand Bailer consists of a piston and check valve encased in an outer cylinder.

At the lower end of the bailer there is a ball check valve or a flapper-type valve,

which allows sand and debris to enter the bailer tube. By lightly stroking up and

down with the wireline tool string the bailer acts to suck sand or debris into the

cylinder through the ball or flapper bottom and trapping the substances inside the

tube.

Various bottom shoe sizes and configurations, as well as extension tubes for the

Sand Bailer are available on request.

SAND BAILER

SAND BAILER

SIZEONE PIECE ASSEMBLY PART NUMBER

TWO PIECE ASSEMBLY PART NUMBER

1” O.D 1105-100-00 1110-100-001 1/4” O.D 1105-125-00 1110-125-001 1/2” O.D. 1105-150-00 1110-150-001 5/8” O.D. 1105-162-00 1110-162-001 3/4” O.D. 1105-175-00 1110-175-002” O.D 1105-200-00 1110-200-002 1/8” O.D. 1105-212-00 1110-212-002 1/4” O.D. 1105-225-00 1110-225-003” O.D. 1105-300-00 1110-300-00


SAND BAILER

HYDROSTATIC BAILER HYDROSTATIC BAILER

The FMS Hydrostatic Bailer is a wireline service tool used when substances to

be bailed cannot be removed by a pump bailer. This sometimes occurs when small

metallic particles or other type debris become lodged on top of the dogs of a lock

mandrel, etc.

The Hydrostatic Bailer is made of a cylinder, about 5 feet long, with a shear disc

mechanism at the bottom. The cylinder is at atmospheric pressure, sealed off

from well pressure with an O-ring. When the obstruction is reached, the disc is

sheared by downward jarring.

Different skirt sizes can be fitted for various tubing and tool sizes.

Brass shear discs are available in different thichnesses for various well pressures.

HYDROSTATIC BAILER

SIZE PART NUMBER1 1/4” O.D. 1140-125-001 1/2” O.D. 1140-150-001 5/8” O.D. 1140-162-002” O.D 1140-200-002 1/2” O.D 1140-250-003” O.D. 1140-300-00


JUNK BASKET BOTTOMSAND BAILER

SAMPLE BAILER SAMPLE BAILER

The FMS Sample Bailer is a wireline service tool

used to take samples from the tubing or casing.

The Sample Bailer consists of a top sub, bailer

tube, and a ball type bottom.

The ball bottom opens when the bailer assembly

is jarred into debris and closes when the bailer is

jarred out.

DUMP BAILER

The FMS Dump Bailer is designed to allow a

variety of fluids to be dumped within the well on

top of any sub-surface device.

Wireline Dump Bailers are available in a variety

of sizes.

The bottom shoe of the Wireline Dump Bailer

should always be matched with the downhole

device upon which fluid is to be dumped.

Bottom assemblies are available with glass shear

disc or O Ring seal piston.

SAMPLE BAILERSIZE PART NUMBER1 1/4” O.D. 1120-125-001 1/2” O.D. 1120-150-001 5/8” O.D. 1120-162-001 3/4” O.D 1120-175-002” O.D 1120-200-002 1/4” O.D 1120-225-002 1/2” O.D. 1120-250-00


SAMPLE BAILER

BLIND BOX

BLIND BOX

The FMS Blind Box is used when heavy

downward jarring on an obstruction is re-

quired. It can also be used to cut wireline

on a rope socket during fishing operations.

The Blind Box is flat on the bottom and

hardened to reduce damage. The O.D. of

the Blind Box should be matched in accor-

dance with the tubing in which it is to be

used.

BLIND BOX

SIZEMAX. O.D. THREAD CONNECTION

FISHING NECK SIZE PART NUMBER

1.250”� 15/16” – 10 UN PIN 1 3/16”� 1150-125-00 1.500”� 15/16” – 10 UN PIN 1 3/16”� 1150-150-00 1.750”� 15/16” – 10 UN PIN 1 3/8”� 1150-175-00 2.250”� 15/16” - 10 UN PIN 1 3/8”� 1150-225-00 2.500”� 15/16” – 10 UN PIN 1 3/8”� 1150-250-00 2.750 1 1/16” – 10 UN PIN 1 3/4”� 1150-275-00


BLIND BOX

CENTRALIZER

The FMS Centralizer is a wireline service tool designed to ensure that

the work string service tool is at its most central position, especially

during wireline operations in deviated wells. It is normally attached to

the tool string just above the running tool, pulling tool, or other ser-

vice tool being used.

The FMS Centralizer is available in a variety of sizes, with either steel

or teflon construction.

TEFLON CENTRALIZER

NOMINAL SIZE PART NUMBER 2”� 1190-200-00 2 1/2”� 1190-250-00 3”� 1190-300-00OTHER SIZES AVAILABLE ON REQUEST

STEEL CENTRALIZER

NOMINAL SIZE MAX. O.D. PART NUMBER 2”� 1.843”� 1185-184-00 2 1/2”� 2.250”� 1185-225-00 3”� 2.700”� 1185-270-00


TEFLON CENTRALIZER

ADJUSTABLE BOW

SPRING CENTRALIZER

ADJUSTABLE BOW SPRING CENTRALIZER

DESCRIPTION PART NUMBER ASSEMBLY 1195-000-00

STEEL CENTRALIZER

ADJUSTABLE

BOW SPRING CENTRALIZER

STEEL CENTRALIZER

TEFLON CENTRALIZER

CHECK SET TOOL

The FMS Set Tool is a wireline ser-

vice tool designed to verify that the

FMSX Locking Mandrel is properly

set in the landing nipple by shearing a

pin located in the tool.

CHECK SET TOOL

CHECK SET TOOL “FMS” �

SIZE PART NUMBER1.250”� 2000-125-001.500”� 2000-150-001.710”� 2000-171-001.781”� 2000-178-001.875”� 2000-187-002.125”� 2000-212-002.188”� 2000-218-002.313”� 2000-231-002.562”� 2000-256-002.750”�2.813”�

2000-275-00

3.688”� 2000-368-003.813”� 2000-381-00

CHECK SET TOOL FMS

TYPE WCIRCULATING PLUG

TYPE ACIRCULATING PLUG

CIRCULATING PLUG

FMS Circulating Plugs are wireline service tools designed to be set in the tubing on top of a collar or tubing stop when

a column of fluid is desired to be held in the tubing.

The Circulating Plug consists of either a ball and seat type or a cone shaped metal to metal seat assembly, and an outer

type seal that seals against the tubing wall when expanded.

The Circulating Plug is widely used during gas lift operations.

TYPE A CIRCULATING PLUG

NOMINAL SIZE PART NUMBER 1 1/2”� 2100-150-00 2”� 2100-200-00 2 1/2”� 2100-250-00 3”� 2100-300-00

TYPE W CIRCULATING PLUG


TYPE A CIRCULATING PLUGTYPE W CIRCULATING PLUG

B AND H EQUALIZING SUBS

The FMS Type “B” and Type “H” Equalizing Subs are compact subs used in

conjunction with flow control devices such as downhole safety valves. The Equal-

izing sub provides a means of equalizing pressure across the downhole device in

order to re-open them or allow for removal from the well.

The Type “B” and Type “H” Equalizing Subs incorporates a single spring loaded

valve which seals on a seat built into the side of the equalizing sub body. In the

closed position, the valve protrudes slightly into the bore of the body. To open the

equalizing valve, an equalizing prong used with the proper pulling tool is inserted

through the downhole safety device and moves the valve off seat and allows the

pressure to equalize.

The Equalizing Sub is installed between the locking mandrel and flow control

device to allow equalization of pressure.

The Type “B” and Type “H” Equalizing Subs are similar in design, except that the

Type “H” has a larger bore.

TYPE B EQUALIZING SUB

SIZE PART NUMBER O.D. I.D. THREAD SIZE1 1/2”� 2205-150-00 1.47”� .44”� 7/8” – 14 2”� 2205-200-00 1.75”� .53”� 1 3/16” – 142 1/2”� 2205-250-00 2.12”� .72”� 1 9/16” – 12 3”� 2205-300-00 2.62”� 1.16”� 2” - 12

TYPE H EQUALIZING SUB

SIZE PART NUMBER O.D. I.D. THREAD SIZE1 1/2”� 2210-150-00 1.47”� .56”� 7/8” – 14 2”� 2210-200-00 1.75”� .69”� 1 3/16” – 142 1/2”� 2210-250-00 2.16”� .87”� 1 9/16” – 12 3”� 2210-300-00 2.72”� 1.50”� 2” – 12

EQUALIZING SUB

TYPE B EQUALIZING SUB

TYPE H EQUALIZING SUB

GAS LIFT EQUIPMENT

FMS Latches are designed to secure valves and accessories in side pocket man-

drels.

LATCHES (GAS LIFT VALVE)

TYPE PART NUMBERBK-2 2230-000-00RK 2235-000-00R 2240-000-00RA 2245-000-00

DUMMY VALVE (GAS LIFT)

TYPE PART NUMBERDK 2250-000-00RD 2255-000-00

BK-2 LATCH RK LATCH R LATCH RA LATCH

DK DUMMY VALVE

LATCHES (GAS LIFT VALVE)

DUMMY VALVE (GAS LIFT)

GAUGE RING (PARAFFIN CUTTER)

The FMS Gauge Ring is a wireline service tool used to gauge the I.D. of the tubing in

which it is run. It should be run prior to running or pulling a sub-surface device, thus

assuring the operator that the tubing is unobstructed down to the depth that he will be

working.

The FMS Gauge Ring may also be used as a paraffin/wax cutter or to determine the

profile of a bridge of debris inside the tubing.




1.250”� 15/16” – 10 UN PIN 1 3/16”� 2650-125-00 1.500”� 15/16” – 10 UN PIN 1 3/16”� 2650-150-00 1.750”� 15/16” – 10 UN PIN 1 3/16”� 2650-175-00 1.843”� 15/16” – 10 UN PIN 1 3/8”� 2650-184-00 1.906”� 15/16” – 10 UN PIN 1 3/8”� 2650-190-00 2.250”� 15/16” - 10 UN PIN 1 3/8”� 2650-225-00 2.343”� 15/16” – 10 UN PIN 1 3/8”� 2650-234-00 2.500”� 15/16” – 10 UN PIN 1 3/8”� 2650-250-00 2.750”� 1 1/16” – 10 UN PIN 1 3/4”� 2650-275-00 2.875”� 1 1/16” – 10 UN PIN 1 3/4”� 2650-287-00


GAUGE RING


GO DEVIL

GO-DEVIL

The FMS Go-Devil is a wireline service tool that makes it possible to cut a conven-

tional wireline when the tool string is entangled in wire or covered with sand or

debris, and the rope socket is no longer clear making a cutter bar or wireline snipper

ineffective.

The Go-Devil is constructed of a solid length of bar with a slot through which the

wireline is passed. Once the wireline is secured through the Go-Devil, it is dropped

downhole in the same manner as a cutter bar.

GO DEVIL

SIZEFISHING NECK SIZE

PART NUMBER 2 FT. LONG



1 1/4”� 1 3/16”� 2270-125-02 2270-125-03 2270-125-051 1/2”� 1 3/8”� 2270-150-02 2270-150-03 2270-150-051 3/4”� 1 3/4”� 2270-175-02 2270-175-03 2270-175-051 7/8”� 1 3/4”� 2270-187-02 2270-187-03 2270-187-052 1/8”� 1 3/4”� 2270-212-02 2270-212-03 2270-212-05


GO DEVIL

IMPRESSION BLOCK

The FMS Impression Block is a wireline service tool used to take impressions of

foreign objects within the well bore. The Impression Block is a useful tool during

fishing operations, as the impression taken will define the shape and relative posi-

tion of the obstruction so that the proper fishing tool may be selected.

The FMS Impression Block is constructed of a hollow steel housing open at one end

and filled with lead, with a pin through the leaded section to keep it in tact. The

impression is made on the exposed soft lead face on the bottom of the Impression

Block.

IMPRESSION BLOCK

IMPRESSION BLOCK



1.250”� 15/16” – 10 UN PIN 1 3/16”� 2300-125-00 1.500”� 15/16” – 10 UN PIN 1 3/16”� 2300-150-00 1.750”� 15/16” – 10 UN PIN 1 3/16”� 2300-175-00 1.875”� 15/16” – 10 UN PIN 1 3/8”� 2300-187-00 2.000”� 15/16” – 10 UN PIN 1 3/8”� 2300-200-00 2.250”� 15/16” - 10 UN PIN 1 3/8”� 2300-225-00 2.375”� 15/16” – 10 UN PIN 1 3/8”� 2300-237-00 2.500”� 15/16” – 10 UN PIN 1 3/8”� 2300-250-00 2.750”� 1 1/16” – 10 UN PIN 1 3/4”� 2300-275-00 2.875”� 1 1/16” – 10 UN PIN 1 3/4”� 2300-287-00 OTHER SIZES AVAILABLE ON REQUEST

IMPRESSION BLOCK

SPANG TYPE STROKE JAR

SPANG TYPE STROKE JARS

FMS “Spang Type” Jars utilize the weight of the stem connected immediately above

to deliver upward or downward jarring impacts by manipulating the wireline at the

surface.

Effective jarring impacts depends on the weight of the stem used, the length of the

stroke of the jars, the size and depth of the tools, the viscosity of the fluid in the

tubing, and the well pressure acting upon the cross sectional area of the wireline.

Jars are constructed of two pieces linked together (similar to a long chain link),

which are free to be extended or collapsed creating a stroke type motion.


SIZESTROKELENGTH

THREAD CONNECTION PIN X BOX


1”� 18”� 5/8 ”- 11 NC 1.000”� 2305-100-18 1 1/4”� 20”� 15/16” - 10 UN 1 3/16’� 2305-125-20 1 1/4”� 30”� 15/16” - 10 UN 1 3/16”� 2305-125-30 1 1/2”� 20”� 15/16” - 10 UN 1 3/8”� 2305-150-20 1 1/2”� 30”� 15/16” – 10 UN 1 3/8”� 2305-150-30 1 3/4’� 20”� 1 1/16” – 10 UN 1 3/4”� 2305-175-20 1 3/4”� 30”� 1 1/16” – 10 UN 1 3/4”� 2305-175-30 1 7/8”� 20”� 1 1/16” – 10 UN 1 3/4”� 2305-187-20 1 7/8”� 30”� 1 1/16’ – 10 UN 1 3/4”� 2305-187-30 2 1/8”� 20”� 1 1/16” – 10 UN 1 3/4”� 2305-212-20 2 1/8”� 30”� 1 1/16’ – 10 UN 1 3/4”� 2305-212-30



TUBULAR JARS

TUBULAR JARS

The FMS Tubular Jar is designed to provide effective jarring forces in conjucntion

with wireline service tools. The Tubular Jar operates on the same principle as

Stroke Jars.

The jar is tubular in construction, with a perforated tube to allow for fluid by-pass

when the plunger is moved up or down.

The Tubular Jar is especially effective in large tubing and casing since there is

less tendency for buckling action of the tube, as might happen with a stroke jar

during fishing and sand bailing operations.

TUBULAR JARS

SIZETHREAD CONNECTION PIN X BOX


1”� 5/8 ”- 11 NC 1.000”� 2310-100-00 1 1/4”� 15/16” - 10 UN 1 3/16’� 2310-125-20 1 1/2”� 15/16” - 10 UN 1 3/8”� 2310-150-20 1 3/4’� 1 1/16” – 10 UN 1 3/4”� 2310-175-20 1 7/8”� 1 1/16” – 10 UN 1 3/4”� 2310-187-20 2 1/8”� 1 1/16” – 10 UN 1 3/4”� 2310-212-20 OTHER SIZES AVAILABLE ON REQUEST

TUBULAR JARS

K KICKOVER TOOL

K KICKOVER TOOLS

The Type “K” Kickover Tool is a wireline service tool used to locate side pocket

mandrels in the well bore. The “K” Kickover Tool is used with a running or

pulling tool to install or retrieve 1" O.D. downhole control devices. The “K”

Kickover Tool uses a centering spring assembly with upper and lower locking

ratchets. When the desired side pocket is reached, upward movement of the

kickover tool shifts the centering spring assembly downward and is held in place

by the ratchets. Downward movement of the kickover tool will allow the ex-

panded centering springs to kick the running or pulling tool over to align with the

mandrel pocket, allowing installation or retrieval of control devices.

K KICKOVER TOOL

DESCRIPTION PART NUMBER 3 SPRINGASSEMBY 2345-000-004 SPRINGASSEMBLY 2350-000-00

AK KICKOVER TOOL

DESCRIPTION PART NUMBER 3 SPRINGASSEMBY 2330-000-004 SPRINGASSEMBLY 2335-000-00

K KICKOVER TOOL

AK KICKOVER TOOL

L KICKOVER TOOLS

The Type “L” Kickover Tool is a wireline service tool used to locate side pocket

mandrels in the well bore. The “L” Kickover Tool is used with a running or pull-

ing tool to install or retrieve 1" and 1 1/2" O.D. downhole control devices. The

“L” Kickover Tool uses a barrel assembly with two spring loaded arms, and lock-

ing dogs located at the lower end of the kickover tool. When the desired side

pocket is reached, upward movement of the kickover tool shifts the barrel assem-

bly downward and is held in place by the locking dogs. Downward movement of

the kickover tool will allow the expanded centering arms to kick the running or

pulling tool over to align with the mandrel pocket, allowing installation or re-

trieval of control devices.

A Spacer Bar is required when the “L” Kickover Tool is used to retrieve 1 1/2"

O.D. control devices.

L KICKOVER TOOL


L2D KICKOVER TOOL


L KICKOVER TOOL

L KICKOVER TOOL

L2D KICKOVER TOOL

R KICKOVER TOOL

The Type “R” Kickover Tool is a wireline service tool used to locate side pocket

mandrels in the well bore. The “R” Kickover Tool is used with a running or pull-

ing tool to install or retrieve 1 1/2" O.D. downhole control devices. The “R”

Kickover Tool uses a barrel assembly with three spring loaded arms, and locking

fingers located at the lower end of the kickover tool. When the desired side pocket

is reached, upward movement of the kickover tool shifts the barrel assembly down-

ward and is held in place by the locking fingers. Downward movement of the

kickover tool will allow the expanded centering arms to kick the running or pull-

ing tool over to align with the mandrel pocket, allowing installation or retrieval of

control devices.

The “R” Kickover Tool does not have a knuckle joint included in the assembly, so

therefore one must be included in the wireline tool string directly above the

kickover tool.

A Spacer Bar is required when the “R” Kickover Tool is used to retrieve 1 1/2"

O.D. control devices.

R KICKOVER TOOL

R KICKOVER TOOL

DESCRIPTION PART NUMBER2” ASSEMBLY 2385-200-002 1/2” ASSEMBLY 2385-250-00

R KICKOVER TOOL

OK-1 KICKOVER TOOL

The Type “OK-1” Kickover Tool is a wireline service tool used to locate side pocket mandrels in the well bore. The “OK-

1” Kickover Tool is used with a running or pulling tool to install or retrieve 1" O.D. downhole control devices.

The “OK-1” Kickover Tool is designed for use in deviated wells making use of an orienting feature that works in

conjunction with the orienting profile of the side pocket mandrel.

OM-1 KICKOVER TOOL

The Type “OM-1” Kickover Tool is a wireline service tool used to locate side pocket mandrels in the well bore. The

“OM-1” Kickover Tool is used with a running or pulling tool to install or retrieve 1 1/2" O.D. downhole control devices.

The “OK-1” Kickover Tool is designed for use in deviated wells making use of an orienting feature that works in

conjunction with the orienting profile of the side pocket mandrel.

A Spacer Bar is required when the “OM-1” Kickover Tool is used to retrieve

1 1/2" O.D. control devices.

OM-1 KICKOVER TOOL

DESCRIPTION PART NUMBER2 1/2” ASSEMBLY 2370-250-003” ASSEMBLY 2370-300-004 1/2” ASSEMBLY 2370-450-00

OK-1 KICKOVER TOOL

DESCRIPTION PART NUMBER2” ASSEMBLY 2360-200-002 1/2” ASSEMBLY 2360-250-003” ASSEMBLY 2360-300-00

OK-1 KICKOVER TOOL

OM-1 KICKOVER TOOL

KNUCKLE JAR

KNUCKLE JOINT

The FMS Knuckle Joint is a wireline tool ac-

cessory used to provide flexibility in the tool

string. The Knuckle Joint is constructed with

a ball and socket and is recommended for use

within all wireline tool strings.

KNUCKLE JOINT


FISHING NECK SIZE

PART NUMBER

1”� 5/8 ”- 11 NC 1.000”� 2395-100-00 1 1/4”� 15/16” - 10 UN 1 3/16’� 2395-125-20 1 1/2”� 15/16” - 10 UN 1 3/8”� 2395-150-20 1 3/4’� 1 1/16” – 10 UN 1 3/4”� 2395-175-20 1 7/8”� 1 1/16” – 10 UN 1 3/4”� 2395-187-20 2 1/8”� 1 1/16” – 10 UN 1 3/4”� 2395-212-20 OTHER SIZES AVAILABLE ON REQUEST

KNUCKLE JAR


FISHING NECK SIZE

PART NUMBER

1 1/4”� 15/16” - 10 UN 1 3/16’� 2390-125-20 1 1/2”� 15/16” - 10 UN 1 3/8”� 2390-150-20 1 3/4’� 1 1/16” – 10 UN 1 3/4”� 2390-175-20 1 7/8”� 1 1/16” – 10 UN 1 3/4”� 2390-187-20 2 1/8”� 1 1/16” – 10 UN 1 3/4”� 2390-212-20 OTHER SIZES AVAILABLE ON REQUEST

KNUCKLE JOINT

KNUCKLE JAR

The FMS Knuckle Jar is simular in design to

the knuckle joint, however, the design incor-

porates a length extension of the socket that

allows the ball to move vertically for light jar-

ring.

KNUCKLE JOINT

KNUCKLE JAR

FMSX SELECTIVE LOCKING MANDREL

The FMSX Locking Mandrel is used to install flow control devices, safety valves

and plugs in landing nipples located in the tubing string. The FMSX Locking

Mandrel incorporates an extra large internal bore for higher volumes and offers

flexibility in running, setting and locking operations that permits the operator

many advantages over other nipple type locking devices.

FMSR Selective Locking Mandrels are available for use with landing nipples in

heavy weight tubing. FMSR Locking Mandrels offer the same benefits as the

FMSX Locking Mandrels.

FMSXN and FMSRN Locking Mandrels are available for “N” designated no-go

landing nipples.

FMSX LOCKING MANDREL

Fishing Neck (1)

Expander Mandrel (2)

Key Spring (10)

Locking Key (3)

Key Housing (4)

Packing Mandrel (6)End Packing Ring (7)

Packing (9)

Center Packing Ring (8)

Packing (9)End Packing Ring (7)

FMSX �LOCKING �MANDREL �

SIZE PART NUMBER1.875”� 2430-187-002.313”� 2430-231-002.750”� 2430-275-002.813”� 2430-281-003.813”� 2430-381-00

�FMSXN �LOCKING �MANDREL �

SIZE PART NUMBER1.875”� 2435-187-002.313”� 2435-231-002.750”� 2435-275-002.813”� 2435-281-003.813”� 2435-381-00

�FMSR �LOCKING �MANDREL �

SIZE PART NUMBER1.710”� 2485-171-001.781”� 2485-178-001.875”� 2485-187-002.125”� 2485-212-002.188”� 2485-218-002.313”� 2485-231-002.562”� 2485-256-003.688”� 2485-368-00

�FMSRN �LOCKING �MANDREL �

SIZE PART NUMBER1.710”� 2490-171-001.781”� 2490-178-001.875”� 2490-187-002.125”� 2490-212-002.188”� 2490-218-002.313”� 2490-231-002.562”� 2490-256-003.688”� 2490-368-00

FMSX & FMSXN LOCKING MANDREL DATA AND DIMENSIONS

SIZE 1.875”� 2.313”� 2.750”� 2.813”� 3.813”�MINIMUM I.D. 1.000”� 1.375”� 1.750”� 1.750”� 2.625”�FISHING NECK I.D. 1.375”� 1.812”� 2.312”� 2.312”� 3.125”�BOTTOM THREADCONNECTION

1 3/8”-14 UN PIN

1 3/4”-12 UN PIN

2 1/4”-12SLB PIN

2 1/4”-12SLB PIN

3.06”-12SLB PIN

FMSR & FMSRN LOCKING MANDREL DATA AND DIMENSIONS

SIZE 1.710”� 1.781”� 1.875”� 2.125”� 2.188”� 2.313”� 2.562”� 3.688”�MINIMUM I.D. .750” � .875”� .875”� .875”� 1.125”� 1.125”� 1.375”� 2.375”�FISHING NECK I.D. 1.062”� 1.375”� 1.375”� 1.375”� 1.812”� 1.812”� 1.812”� 3.125”�BOTTOM THREADCONNECTION

1 1/8-16UN PIN

1 3/8-14UN PIN

1 3/8-14UN PIN

1 3/8-14UN PIN

1 3/4-12UN PIN

1 3/4-12UN PIN

2”-12SLB PIN

3.06”-12SLB PIN

FMSX EQUALIZING SUB

The FMSX Equalizing Subs are used as a means of equalizing pressure

differentials across a flow control device.

They are designed to be used with large bore mandrels such as FMSX

Locking Mandrel. The maximum O.D. ring on the FMSX Equalizing

Sub serves as a no-go ring for type FMSXN Locking Mandrels.

FMSR Equalizing Subs are available for use with FMSR Locking Man-

drels.

FMSX EQUALIZING SUB

SIZE PART NUMBER MAX. O.D. MIN. I.D.1.875”� 2720-187-01 1.870”� .875”�2.313”� 2720-231-01 2.305”� 1.218”�2.750”�2.813”� 2720-275-01 2.745”� 1.625”�3.813”� 2720-381-01 3.807”� 2.500”�

FMSR EQUALIZING SUB

SIZE PART NUMBER MAX. O.D. MIN. I.D.1.710”� 2715-171-01 1.706”� .625”�1.781”� 2715-178-01 1.776”� .780”�1.875”� 2715-187-01 1.870”� .780”�2.125”� 2715-212-01 2.120”� .780”�2.188”� 2715-218-01 2.183”� 1.000”�2.313”� 2715-231-01 2.308”� 1.000”�2.562”� 2715-256-01 2.557”� 1.190”�

FMSX EQUALIZING SUB

FMSX EQUALIZING SUB

FMSR EQUALIZING SUB

TYPE N NO-GO SUB

The Type N No-Go sub is used in conjunction with the FMSS Locking Mandrel

when a Type N No-Go Mandrel is to be used. The N No-Go Sub is screwed on to

the locking section of the FMSS Mandrel just below the packing section to con-

vert into the Type N No-Go Mandrel.

N NO GO SUB

TYPE N NO GO SUB

NOMINAL SIZE PART NUMBER 2”� 2535-200-00 2 1/2”� 2535-250-00 3”� 2535-300-00

FMSS LOCKING MANDREL

DESCRIPTION PART NUMBER1.875” FMSS LOCKING MANDREL W/ S-1 KEYS 2405-187-001.875” FMSS LOCKING MANDREL W/ S-2 KEYS 2410-187-001.875” FMSS LOCKING MANDREL W/ S-3 KEYS 2415-187-001.875” FMSS LOCKING MANDREL W/ S-4 KEYS 2420-187-00

2.313” FMSS LOCKING MANDREL W/ S-1 KEYS 2405-231-00

2.313” FMSS LOCKING MANDREL W/ S-2 KEYS 2410-231-002.313” FMSS LOCKING MANDREL W/ S-3 KEYS 2415-231-002.313” FMSS LOCKING MANDREL W/ S-4 KEYS 2420-231-00

2.875” FMSS LOCKING MANDREL W/ S-1 KEYS 2405-287-002.875” FMSS LOCKING MANDREL W/ S-2 KEYS 2410-287-002.875” FMSS LOCKING MANDREL W/ S-3 KEYS 2415-287-002.875” FMSS LOCKING MANDREL W/ S-4 KEYS 2420-287-00

FMSS LOCKING MANDREL DATA AND DIMENSIONS

NOMINAL SIZE 2” � 2 1/2”� 3”�PACKING O.D. 1.875”� 2.313”� 2.875”�MIMIMUM I.D. .687” � .875”� 1.500”�FISHING NECK O.D. 1 3/8”� 1 3/4”� 2 5/16”�

FMSS LOCKING MANDREL

FMSS LOCKING MANDREL WITH LOCATOR

The FMSS Locking Mandrel is used to install flow control devices, safety valves

and plugs in nipples located in the tubing. The FMSS Locking Mandrel has a mating

locator section with position keys that are used for landing nipple selection. Posi-

tions 1 through 5 are available.

TYPE N NO GO SUB

W LOCKING MANDRELD COLLAR LOCK MANDREL

TYPE D COLLAR LOCK MANDREL

The “D” Collar Lock Mandrel locates and locks in

tubing coupling recesses. It can be run or pulled

by wireline methods under pressure. The sealing

element is mechanically locked in the set position

to allow pressure differentials to be held from above

or below the locking mandrel and flow control de-

vice.

TYPE W LOCKING MANDREL

The “W” Locking Mandrel is a slip type mandrel

used to install flow control devices in the tubing

when landing nipples are unavailable or cannot be

used. The “W” Mandrel employs a rubber seal as-

sembly that seals off against the tubing wall once

it is expanded.







LUBRICATOR SECTION

LUBRICATOR SECTION

The FMS Lubricator Section is a pressure containing cylinder used when per-

forming wireline operations. Its purpose is to allow the wireline tool string to be

raised above the wellhead valve prior to and after wireline operations and there-

fore enables the wellhead valve to be opened and closed, allowing entry and exit

from the well bore.

The FMS Lubricator Section consists typically of a lubricator tube and quick

union connections on the upper and lower ends.

FMSB QUICK UNIONS ARE INTERCHANGEABLE WITH BOWEN

TYPE UNIONS

FMSO QUICK UNIONS ARE INTERCHANGEABLE WITH OTIS TYPE

UNIONS

ALL LUBRICATOR SECTIONS ARE AVAILABLE WITH OR WITHOUT A

BLEED PORT

SPECIFY STANDARD OR H2S SERVICE WHEN ORDERING

SPECIFY QUICK UNION TYPE WHEN ORDERING

MAGNET

The FMS Magnetic Fishing Tool is a wireline ser-

vice tool used to magnetically attract and retrieve

ferrous debris lost in the well bore.

The FMS Magnet consists of a top body with a pin

connection and fishing neck. The body houses the

magnet insert, with an open faced bottom cap

threaded to the body to retain the magnet insert.

FMS Skirted Magnetic Fishing Tools are also avail-

able. This assembly employs the use of a sleeve

made from nonferrous material, with its main pur-

pose being to protect the debris from dislodging

after it is picked up.

MAGNET

SIZEMAX. O.D. PART NUMBER 1 1/2”� 2525-150-00 1 3/4”� 2525-175-00 2 1/4”� 2525-225-00 2.700”� 2525-2700-00


SKIRTED MAGNET

SIZEMAX. O.D. PART NUMBER 1 3/4”� 2530-175-00 2 1/4”� 2530-225-00 2.700”� 2530-2700-00


MAGNET SKIRTED MAGNET

SKIRTED MAGNET

MAGNET

FMS OVERSHOT OVERSHOT

FMS Wireline Overshots are slip type, designed specifically for wireline opera-

tions. They are used to retrieve wireline tools or parts of wireline tools that are

lost in the well bore.

FMS Wireline Overshots are available in a variety of sizes, each size having a

wide range of hardened and tempered slips.

Threaded main bodies are available for use with a large range of bell guides nec-

essary for fishing for small diameter tools in large internal diameter tubing or

casing.

BULLDOG SPEAR

The FMS Bulldog Spear is a wireline fishing tool designed to catch the internal

diameter of a wireline tool or other type “fish” requiring an internal latch.

The FMS Bulldog Spear is made especially for wireline operations and is avail-

able with a wide range of hardened and tempered slips to withstand heavy fishing

operations.

FMS OVERSHOT


FMS OVERSHOT

TYPE “G” PACKOFF ASSEMBLY

The Type “G” Packoff Assembly is designed to

straddle and pack-off holes or other communica-

tions in the tubing string. The Type “G” Packoff is

installed using normal wireline methods under pres-

sure, enabling the assembly to be set without kill-

ing the well. The Type “G” Packoff offers a large

bore and is suited for installations where a high

volume of production is desired.

The Type “G” Packoff is installed using a slip type

or collar type stop at the bottom of the assembly.

Spacer Pipe is added between the lower and upper

sections of the packoff so that the packoff assem-

bly straddles the communication in the tubing. The

upper packoff section is anchored by a slip type hold

down stop. The packing element on the “G” Packoff

Assembly seals against the tubing wall and is held

in position by a mechanical lock.

Landing Shoes and Recepticals are available to in-

crease the amount of spacer pipe required. The

spacer pipe is run between the Landing Shoe and

Receptical. The additional spacer pipe can then be

installed without requiring additional wireline lu-

bricator sections.

Landing Shoes and Recepticals are available with

O Ring or Packing type seals.

TYPE “G” PACKOFF ASSEMBLY

DESCRI PTION PART NUMBER2” UPPER ASSEMBLY 2580-200-002” LOWER ASSEMBLY 2585-200-002 1/2” UPPER ASSEMBLY 2580-250-002 1/2” LOWER ASSEMBLY 2585-250-003” UPPER ASSEMBLY 2580-300-003” LOWER ASSEMBLY 2585-300-00

O RING TYPE LANDING SHOE


O RING TYPE

RECEPTICAL

O RING TYPE

LANDING SHOE

G PACKOFF UPPER SECTION G PACKOFF LOWER SECTION

O RING TYPE RECEPTICAL


TYPE G PACKOFF ASSEMBLY

PARAFFIN SCRATCHER

PARAFFIN SCRATCHER

The FMS Paraffin Scratcher is a wireline service tool used to loosen paraffin

accumulation from the inside of the tubing string.

The FMS Paraffin Scratcher is made from a solid rod, drilled with a series of

holes along four generatrices. Pieces of wireline are inserted into the holes. The

lengths of the wireline pieces depend on the tubing I.D.

PARAFFIN SCRATCHER

DESCRIPTION PART NUMBER THREAD CONNECTIONFISHING NECK SIZE

ASSEMBLY 2655-000-00 15/16” – 10 UN PIN 1 3/16” O.D.

PARAFFIN SCRATCHER

“D” PLUG

The “D” Plug Assembly is used in conjunction with a locking device to plug the tubing string. It incorporates a hycar

type seal plus a metal to metal seat.

The “D” Plug Assembly is designed to hold pressure from below only and is used to reduce surface pressure or com-

pletely bleed off the pressure of the tubing string.

PS AND PN PLUGS

The Type “PS” Plug is designed for use with a lock-

ing mandrel used in type S landing nipples. (FMSS

Locking Mandrel). Type “PN” Plug is designed for

use with a locking mandrel used in type N landing

nipples. (FMSN Locking Mandrel).

In both applications, the “P” Plug Assembly is de-

signed to hold pressure from above and below the

plug choke. This “positive” type plug has a

removeable equalizing prong and large flow area

for equalization after the prong is removed.

PS AND PN PLUG

NOMINAL SIZE 2” � 2 1/2”� 3” �PART NUMBER“PS” ASSEMBLY 2685-200-00 2685-250-00 2685-300-00PART NUMBER“PN” ASSEMBLY 2680-200-00 2680-250-00 2680-300-00FISHING NECK O.D. PRONG

1.000”� 1.000”� 1.750”�

FISHING NECK O.D.LOCKING MANDREL

1.375”� 1.750”� 2.312”�

D PLUG

PS PLUG

D PLUG

NOMINAL SIZE PART NUMBER MAX. O.D. I.D. BORE 2" 2735-200-00 1.75" .53"� 2 1/2" 2735-250-00 2.12" .72" 3" 2735-300-00 2.62" 1.16"

D PLUG

FMSPX PLUG GROMMET TYPE

FMSPX PLUG ASSEMBLY

The FMSPX Assembly is a positive type plug choke

designed to hold pressure from above and below.

The FMSPX Plug is used is used in conjunction with

the FMSX Locking Mandrel. It employs a remov-

able equalizing prong, which when retrieved ex-

poses a series of equalizing port holes in the prong

housing. The locking mandrel is then retrieved on

the next wireline trip.

The FMSPX Plug Assembly is used for testing

packer leakage, removing the wellhead, testing tub-

ing and separating zones during remedial workovers.

The FMSPR Plug Assembly is available for wells

with heavy weight tubing requiring the use of the

FMSR Locking Mandrel.

FMSPX PLUG ASSEMBLY

SIZEPART NUMBERPACKING TYPE

PART NUMBERGROMMET TYPE

1.875”� 2705-187-00 2710-187-002.313”� 2705-231-00 2710-231-002.750”� 2705-275-00 2710-275-00 OTHER SIZES AVAILABLE ON REQUEST

FMSPR PLUG ASSEMBLY

SIZE PART NUMBER1.710”� 2700-171-001.781”� 2700-178-001.875”� 2700-187-002.125”� 2700-212-002.188”� 2700-218-002.313”� 2700-231-002.562”� 2700-256-00

FMSPX PLUG PACKING TYPE

FMSPX PLUG ASSEMBLY

FMSPR PLUG ASSEMBLY

FMSXX PLUG

FMSXX PLUG ASSEMBLY

The FMSXX Plug Assembly is a positive type plug that is designed to hold pres-

sure from above and below. It employs the use FMSX Equalizing Sub and a

bottom cap adapted to the FMSX Locking Mandrel.

The FMSRR PLUG Assembly is available for wells with heavy weight tubing

requiring the use of the FMSR Locking Mandrel.

FMSRR PLUG ASSEMBLY

SIZE PART NUMBER1.710”� 2715-171-001.781”� 2715-178-001.875”� 2715-187-002.125”� 2715-212-002.188”� 2715-218-002.313”� 2715-231-002.562”� 2715-256-00

FMSXX PLUG ASSEMBLY

SIZE PART NUMBER1.875”� 2720-187-002.313”� 2720-231-002.750”� 2720-275-003.813”� 2720-381-00


FMSRR PLUG ASSEMBLY

FMSXX PLUG ASSEMBLY

GG PULLING TOOL

“GG” PULLING TOOL

The Type GG Puling Tool is designed primarily to retrieve prongs with fishing

necks from subsurface devices such as the type PS and PX Plug Chokes. It is also

used as a fishing tool for latching tools with fishing necks that have become dam-

aged during regular pulling procedures.

The Type GG Pulling Tool consists of a top sub, cylinder, collect type dogs, and

bottom sub.

GG PULLING TOOL

SIZE PART NUMBER2” X 1” � 2900-100-002” X 1 3/16”� 2900-118-002” X 1 3/8”� 2900-137-002 1/2” X 1 3/4”� 2900-175-003” X 2 5/16”� 2900-231-00

GG PULLING TOOL FOR BK LATCH

ASSEMBLY 2900-087-00

GG PULLING TOOL

GR ADAPTERGS PULLING TOOL

“GS” PULLING TOOL

The FMS “GS” Pulling Tool is a wireline service tool

designed to retrieve flow control devices from the well

bore. The “GS” Pulling Tool is designed to engage an

internal type fishing neck. The tool is available in a

wide range of sizes, for standard or H2S service.

The “GS” Pulling Tool is designed to be released from

the downhole device by downward jarring.

“GR” SHEAR UP ADAPTER

The FMS “GR” Shear-Up Adapter is a wireline pull-

ing tool device used to convert a Type “GS” Pulling

Tool. The “GR” Adapter, with shear pin in place is

screwed on top of the “GS” Pulling Tool. The shear

pin on the “GS” Pulling Tool must be removed. The

complete assembly, now a Type “GR” Pulling Tool

will operate with a shear-up to release action instead

of a shear down.

The FMS “GR” Adapter is available to suit all sizes

of the”GS” Pulling Tool.

“GS” PULLING TOOL

NOMINAL SIZE 1 1/2” � 2”� 2 1/2”� 3”� 4’�PART NUMBER 2910-150-00 2910-200-00 2910-2160-00 2910-300-00 2910-400-00SPECIFICATIONSWILL ENGAGEFISHING NECK I.D.

1.187”� 1.375”� 1.812”� 2.313”� 3.125”�

TOP THREADCONNECTION

15/16” – 10 15/16” – 10 15/16” – 10 1 1/16” – 10 1 1/16” – 10

FISHING NECK O.D.ON TOOL

1.187”� 1.375”� 1.750”� 2.313”� 2.313”�

BOTTOM THREADCONNECTION

1/2” – 13 1/2” – 13 5/8” – 11 5/8” – 11 2 1/8” – 12


“GR” ADAPTER” �


GS PULLING TOOL

GR ADAPTER

1.062”

JD PULLING TOOL

“JD” SERIES WIRELINE PULLING TOOL

The FMS “JD” Pulling Tool is a wireline service tool designed to remove retriev-

able subsurface devices with external fishing necks from a well. This tool has collet-

type dogs with a large latching area. It is also available with different length cores

which make the reach of the tool adaptable to retrieve subsurface devices with

fishing necks of different lengths.

The “JD” Pulling Tool utilizes the “D” top sub which is made up to the skirt of the

tool. The dogs, which are mounted on the skirt, are inserted into the vertical open-

ings in the skirt. The “JD” Series Pulling Tool can be released, if necessary from the

retrievable device by downward jarring.

In the Pulling Tool nomenclature, the second letter is used to designate the direction

of shear release. A “JD” is a “jar down” release tool. The third letter designates core

length: with a “C” being a “long” core and an “S” core being a “short” core. A third

core length, designated as an “L” core is even shorter but has limited applications.

“JD” PULLING TOOL

NOMINAL SIZE “JDC” ASSEMBLY “ �JDS” ASSEMBLY 1 1/4”� 2930-125-00 1 3/8”� 2930-137-00 1 1/2”� 2930-150-00 2935-150-00 1 5/8”� 2930-162-00 2935-162-00 2”� 2930-200-00 2935-200-00 2 1/2”� 2930-250-00 2935-250-00 3”� 2930-300-00 2935-300-00 4”� 2930-400-00 2935-400-00

“JD” AND “JU” SERIES PULLING TOOLDATA AND DIMENSIONS

SIZE TYPETO ENGAGEFISHING NECK O.D.

REACH MAX. O.D. TOP THREADCONNECTION

1 1/4”� JDC .875”� 1.937”� 1.281”� 15/16” – 101 3/8”� JDC 1.000”� 1.875”� 1.375”� 15/16” – 10

1 1/2”� JDC 1.187”� 1.093”� 1.422”� 15/16” – 101 1/2”� JDS 1.187”� 1.843”� 1.422”� 15/16” – 101 1/2”� JUC 1.187”� 1.093”� 1.422”� 15/16” – 101 1/2”� JUS 1.187”� 1.843”� 1.422”� 15/16” – 10

1 5/8”� JDC 1.187”� 1.093”� 1.625”� 15/16” – 10

2”� JDC 1.375”� 1.437”� 1.859”� 15/16” – 10 2”� JDS 1.375”� 2.125”� 1.859”� 15/16” – 10 2”� JUC 1.375”� 1.437”� 1.859”� 15/16” – 10 2”� JUS 1.375”� 2.125”� 1.859”� 15/16” – 10

2 1/2”� JDC 1.750”� 1.312”� 2.250”� 15/16” – 102 1/2”� JDS 1.750”� 2.187”� 2.250”� 15/16” – 102 1/2”� JUC 1.750”� 1.312”� 2.250”� 15/16” – 102 1/2”� JUS 1.750”� 2.187”� 2.250”� 15/16” – 10

3”� JDC 2.312”� 1.437”� 2.796”� 1 1/16” - 10 3”� JDS 2.312”� 2.125”� 2.796”� 1 1/16” – 10 3”� JUC 2.312”� 1.437”� 2.796”� 1 1/16” – 10 3”� JUS 2.132”� 2.125”� 2.796”� 1 1/16” – 10

4”� JDC 3.125”� 2.312”� 3.750”� 1 1/16” – 10 4”� JUC 3.125”� 2.312”� 3.750”� 1 1/16” – 10

JD PULLING TOOL

JD AND JU SERIES PULLING TOOLDATA AND DIMENSIONS

JUC Long core - short reach JU JUS Short core - long reach

JUL Very short core - very long reach

To convert a JU pulling tool into a JD, change the top sub and install a core cap to the core.

JDC Equivalent to JUC JD JDS Equivalent to JUS

JDL Equivalent to JUL

“JU” SERIES PULLING TOOL

The FMS “JU” Pulling Tool is a wireline service tool designed to remove retriev-

able subsurface devices with external fishing necks from a well. This tool has

collet-type dogs with a large latching area. It is also available with different length

cores which make it adaptable to retrieve subsurface devices with fishing necks

of different lengths.

The “JU” Pulling Tool utilizes the “U” top sub which is made up to the core of

the tool. The “JU” Pulling Tool can be released, if necessary from the subsurface

device by continued upward jarring.

In the Pulling Tool nomenclature, the second letter is used to designate the direc-

tion of shear release. A “JU” is a “jar up” release tool. The third letter designates

core length; a “C” being a “long” core and “S” being “short” core. A third core

length, designated as an “L” core is even shorter but has limited application.

The “JD” and “JU” Pulling Tools differ only in the manner of shear release. The

“JD” for jar down to release and the “JU” for jar up to release. The accompanying

chart provides reach data along with the core type necessary.

“JU” PULLING TOOL

NOMINAL SIZE “JUC” ASSEMBLY “JUS” ASSEMBLY 1 1/4”� 2940-125-00 1 3/8”� 2940-137-00 1 1/2”� 2940-150-00 2945-150-00 1 5/8”� 2940-162-00 2945-162-00 2”� 2940-200-00 2945-200-00 2 1/2”� 2940-250-00 2945-250-00 3”� 2940-300-00 2945-300-00 4”� 2940-400-00 2945-400-00

JU PULLING TOOL

JU PULLING TOOL

R PULLING TOOL

“R” PULLING TOOL

The FMS “R” Pulling Tool is a wireline service tool used to retrieve subsurface

devices with external fishing necks from a well. This tool utilizes a set of three

dogs to engage the fishing neck.

The “R” Pulling Tool is available in a wide range of sizes, with three reaches in

each size. All tools can be supplied for standard or H2S service.

The “R” Pulling Tool is designed to be released from the downhole device by

upward jarring.

By changing only the core of the “R” Pulling Tool, it is possible to obtain a “RB”,

“RS”, or “RJ” Pulling Tool.

“R” PULLING TOOL

NOMINAL SIZE “RB” ASSEMBLY “RS” ASSEMBLY “RJ” ASSEMBLY 1 1/2”� 2960-150-00 2965-150-00 2970-150-00 2”� 2960-200-00 2965-200-00 2970-200-00 2 1/2”� 2960-250-00 2965-250-00 2970-250-00 3”� 2960-300-00 2965-300-00 2970-300-00 4”� 2960-400-00 2965-400-00 2970-400-00

“R” PULLING TOOLDATA AND DIMENSIONS



1 1/2”� RB 1.187”� 1.265”� 1.430”� 15/16” – 101 1/2”� RS 1.187”� 1.797”� 1.430”� 15/16” – 101 1/2”� RJ 1.187”� 2.547”� 1.430”� 15/16” – 10

2”� RB 1.375”� 1.219”� 1.770”� 15/16” – 10 2”� RS 1.375”� 1.984”� 1.770”� 15/16” – 10 2”� RJ 1.375”� 2.547”� 1.770”� 15/16” – 10

2 1/2”� RB 1.750”� 1.203”� 2.180”� 15/16” – 102 1/2”� RS 1.750”� 1.984”� 2.180”� 15/16” – 102 1/2”� RJ 1.750”� 2.547”� 2.180”� 15/16” – 10

3”� RB 2.312”� 1.297”� 2.740”� 1 1/16” – 10 3”� RS 2.312”� 2.156”� 2.740”� 1 1/16” – 10 3”� RJ 2.312”� 2.609”� 2.740”� 1 1/16” – 10

4”� RB 3.125”� 1.406”� 3.718”� 1 1/16” – 10 4”� RS 3.125”� 2.156”� 3.718”� 1 1/16” – 10

R PULLING TOOL

R PULLING TOOLDATA AND DIMENSIONS

S PULLING TOOL

“S” PULLING TOOL

The FMS “S” Pulling Tool is a wireline service tool used to retrieve subsurface

with external fishing necks from a well. This tool utilizes a set of three dogs to

engage the fishing neck.

The “S” Pulling Tool ia available in a wide range of sizes, with three reaches of

each size. All tools can be supplied for standard or H2S service.

By changing the only the core of the “S” Pulling Tool, it is possible to obtain types

“SB”, “SS”, or “SJ” Pulling Tools.

The “S” Pulling Tool is designed to be released from the downhole device by

downward jarring. Therefore the “S” Pulling Tool is particularly suited for use as

a pulling tool when extensive jarring is required.

Because of the downward shear release of the “S” Pulling Tool, it is particularly

useful as a running tool for collar stops, pack-off anchor stops, and other subsur-

faces devices landed against a positive no-go.

S PULLING TOOLDATA AND DIMENSIONS



1 1/2”� SB 1.187”� 1.297”� 1.437”� 15/16” – 101 1/2”� SS 1.187”� 1.781”� 1.437”� 15/16” – 10

2”� SB 1.375”� 1.219”� 1.770”� 15/16” - -10 2”� SS 1.375”� 2.031”� 1.770”� 15/16” – 10

2 1/2”� SB 1.750”� 1.281”� 2.180”� 15/16” – 102 1/2”� SS 1.750”� 2.000”� 2.180”� 15/16” – 10

3”� SB 2.312”� 1.500”� 2.740”� 1 1/16” - 10 3”� SS 2.312”� 2.219”� 2.740”� 1 1/16” – 10

4”� SB 3.125”� 1.800”� 3.718”� 1 1/16” – 10

S PULLING TOOL

NOMINAL SIZE “SB” ASSEMBLY “SS” ASSEMBLY “SJ” ASSEMBLY 1 1/2”� 2975-150-00 2980-150-00 2985-150-00 2”� 2975-200-00 2980-200-00 2985-200-00 2 1/2”� 2975-250-00 2980-250-00 2985-250-00 3”� 2975-300-00 2980-300-00 2985-300-00 4”� 2975-400-00 2980-400-00 2985-400-00

S PULLING TOOLDATA AND DIMENSIONS

S PULLING TOOL

QUICK LOCK

The FMS Quick Lock provides a fast and strong method of tool coupling that

is entirely hand operated eliminating the need for threads, wrenches, or lever

bars.

QUICK LOCK

SIZE 1 1/4”� 1 1/2”� 1 3/4”� 1 7/8”�PART NUMBER 3030-125-00 3030-150-00 3030-175-00 3030-187-00

“PRS” PULLING TOOL” �

NOMINAL SIZE 2” � 2 1/2”� 3”�PART NUIMBER 2950-200-00 2950-250-00 2950-400-00

“PRS” PULLING TOOL

The FMS “PRS” Type Pulling Tool is a wireline service tool used to

retrieve subsurface devices with inside fishing necks from a well.

QUICK LOCK

PRS PULLING TOOL

QUICK LOCK

QUICK UNION

The FMS Quick Union provides a means of assembling lubricator sections together, as well as adapt-

ing to the wireline blow out preventer and wireline stuffing box.

The FMS Quick Unions are self aligning and require only hand tightening to seal. The Quick Unions

feature an acme type thread with a primary O-Ring seal.

A wide range of Quick Union sizes are available.

FMSB QUICK UNIONS ARE INTERCHANGEABLE WITH THE BOWEN UNION.

FMSO QUICK UNIONS ARE INTERCHANGEABLE WITH THE OTIS UNION.

SPECIFY STANDARD OR H2S SERVICE WHEN ORDERING.

QUICK UNION

SIZE / TYPE 2” “FMSB” � 2 1/2” “FMSB” � 3” “FMSB” � 5” X 4” “FMSO” �PART NUMBER 3050-200-00 3050-250-00 3050-300-00 3055-500-00

QUICK UNION

��

QUICK UNION

MULTI STRAND ROPE SOCKET


The FMS Slip Type Rope Socket is designed for use

with small multi-strand lines through 5/16" diameter. The

FMS Slip Type Rope Socket consists of a body, sub,

slips, and set screw featuring easy assembly. The slips

are designed to cause the line to break under severe load-

ing at specific percentage of the full line tensile strength

in the event that the wireline tool string becomes stuck.

The operator is assured that the line will break at the

Rope Socket, rather than up-hole, allowing retrieval of

the line.

SINGLE STRAND ROPE SOCKET

SIZE PART NUMBER FISHING NECK O.D. THREAD CONNECTION

1”� 3100-100-00 1.000”� 5/8” – 11 NC1 1/4”� 3100-125-00 1.187”� 15/16” – 10 UN1 1/2”� 3100-150-00 1.375”� 15/16” – 10 UN1 3/4”� 3100-175-00 1.750”� 1 1/16” – 10 UN1 7/8”� 3100-187-00 1.750”� 1 1/16” – 10 UN2 1/8”� 3100-212-00 1.750”� 1 1/16” – 10 UN

BRASS WEDGE ROPE SOCKET

SIZEWIRESIZE PART NUMBER FISHING NECK O.D. THREAD CONNECTION

1 1/4”�0.092”�0.108”�0.125”�0.187”�

3105-125-00 3110-125-00 3115-125-00 3120-125-00

1.187”� 15/16” – 10 UN

1 1/2”�0.092”�0.108”�0.125”�0.187”�

3105-150-00 3110-150-00 3115-150-00 3120-150-00

1.375”� 15/16” – 10 UN

1 3/4”�0.092”�0.108”�0.125”�0.187”�

3105-175-00 3110-175-00 3115-175-00 3120-175-00

1.750”� 1 1/16” – 10 UN

1 7/8”�

0.092”�0.108”�0.125”�0.187”�

3105-187-00 3110-187-00 3115-187-00 3120-187-00

1.750”� 1 1/16” – 10 UN

BRASS WEDGE ROPE SOCKET

SINGLE STRAND ROPE SOCKET


SIZE PART NUMBER FISHING NECK O.D. THREAD CONNECTION

1 1/4”� 3125-125-00 1.187”� 15/16” – 10 UN1 1/2”� 3125-150-00 1.375”� 15/16” – 10 UN1 3/4”� 3125-175-00 1.750”� 1 1/16” – 10 UN1 7/8”� 3125-187-00 1.750”� 1 1/16” – 10 UN2 1/8”� 3125-212-00 1.750”� 1 1/16” – 10 UN

ROPE SOCKET (BRASS WEDGE TYPE)

The FMS Brass Wedge Rope Socket is used to securely attach

.108" and larger wireline to the tool string. It utilizes a brass

wedge to keep the wireline attached within the rope socket in-

stead of a spring, thimble and spool as used in conventional

rope sockets.

ROPE SOCKET (SINGLE STRAND)

The FMS Rope Socket is used to securely attach .082" or .092" wireline to the tool

string. The FMS Rope Socket consists of a body, spring, spring support thimble, and

disc.

JC-3 RUNNING TOOL

RUNNING TOOLS

FMS Side Pocket Running Tools are wireline service tools used to install downhole

control devices in side pocket mandrels. The side pocket control device is at-

tached to the running tool with shear pins. The running tool must be used with the

proper kickover tool in order to set the control device in the side pocket mandrel.

RUNNING TOOLS

TYPE “JC-3” � “JK” � “GA-2” � “RK-1” �PART NUMBER 3130-000-01 3130-000-02 3130-000-06 3130-000-08 OTHER TYPES AND SIZES AVAILABLE ON REQUEST

RK-1 RUNNING TOOLGA-2 RUNNING TOOLJK RUNNING TOOL

RUNNING TOOLS

C-1 RUNNING TOOL

C-1 RUNNING TOOL

The FMS Type “ C-1” Running Tool is a wireline service tool used to install

locking mandrels with external fishing necks in the appropriate landing nipple.

The “C-1” Running Tool is run using a thread protector, which is the same O.D.

as the body of the tool to set selective type locking mandrels. A seal bore locating

ring may be used instead to set top no-go type locking mandrels.

The “C-1” Running Tool is threaded internally to accept the Type “A” or Type

“N-1” Shank

“C-1” RUNNING TOOL

NOMINAL SIZE 2”� 2 1/2”� 3”� 4”�PART NUMBER 3135-200-00 3135-250-00 3135-300-00 3135-400-00

C-1 RUNNING TOOL

D RUNNING TOOL

D RUNNING TOOL(COLLECT TYPE)

D RUNNING TOOL (COLLET TYPE)

The FMS Type “D” Running Tool Collet Type is used to install

the Type “D” Collar Lock Mandrel in the tubing collar recess.

“D” RUNNING TOOL

NOMINAL SIZE 2”� 2 1/2”� 3”�PART NUMBER 3140-200-00 3140-250-00 3140-300-00

“D” RUNNING TOOL (COLLET TYPE)

NOMINAL SIZE 2” � 2 1/2”� 3”�PART NUMBER 3145-200-00 3145-250-00 3145-300-00

D RUNNING TOOL

The FMS Type “D” Running Tools are wireline

service tools used to install the Type “C” and Type

“CS” Locking Mandrels in the appropriate land-

ing nipples. Most Type “D” Running tools are

threaded internally so that a prong can be used for

equalization purposes. The Type “D” Running Tool

requires downward jarring to set the locking man-

drel and upward jarring to release the running tool

from the locking mandrel.

D RUNNING TOOL (COLLET TYPE)

D RUNNING TOOL

J RUNNING TOOL

G STOP RUNNING TOOL

G STOP RUNNING TOOL

The FMS G Stop Running Tool is wireline service tool that en-

ables the operator to set the G Type Tubing Stop at any pre-deter-

mined depth desired. The G Stop Running Tool is retained in the

running position with two shear pins and attached to the stop

with one shear pin.��

G STOP RUNNING TOOL


“J” RUNNING TOOL


J RUNNING TOOL

The FMS “J” Running Tool is a wireline service

tool used to install the Type S Locking Mandrel in

the S landing nipple. The subsurface device is held

in place on the “J” Running Tool by two 3/16" shear

pins inserted through horizontal tangential grooves.

Once the subsurface device is lowered into the land-

ing nipple and locked in place, the shear pins are

sheared by upward jarring. This releases the Run-

ning Tool and allows it to be pulled from the tub-

ing.

G STOP RUNNING TOOL

J RUNNING TOOL

W RUNNING TOOL

PS RUNNING TOOL

PS RUNNING TOOL

The FMS “PS” Running Tool is used with subsurface controls

having removable prong assemblies. The extra deep recess al-

lows room for the prong fishing neck extending above the tool

fishing neck.

The “PS” Running Tool is used to install types PS

and PN Plug Assemblies in landing nipples. The

operation procedure of the “PS” Running Tool is

identical to the operation of the “J” Running Tool.

“PS” RUNNING TOOL


“W” RUNNING TOOL

NOMINAL SIZE 2” – 2 1/2” � 3”�PART NUMBER 3185-200-00 3185-300-00

W RUNNING TOOL

The FMS “W” Running Tool is a wireline service

tool used to install the Type W Locking Mandrel at

a predetermined depth in the tubing string.

PS RUNNING TOOL

W RUNNING TOOL

FMSX RUNNING TOOL FMSX SELECTIVE RUNNING TOOL

The FMSX Selective Running Tool is designed to install subsurface controls us-

ing a Type FMSX Locking Mandrel. The selective features of the FMSX Run-

ning Tool allow the operator to install the downhole device in a pre-determined

Type X Landing Nipple by adjusting the tool into the selective position. If the

subsurface control is to be installed in the upper most landing nipple, the locking

mandrel may be run with the keys in the control or locating position.

In addition to setting the FMSX Locking Mandrel, the Running Tool may be used

to locate Type FMSX Landing Nipples.

The FMSR Selective Running Tool, similar in design, is available in a wide range

of sizes to install Type FMSR Locking Mandrels in heavy weight tubings.

FMSX RUNNING TOOL

SIZE PART NUMBER1.500”� 3200-150-001.625”� 3200-162-001.875”� 3200-187-002.313”� 3200-231-002.750”� 3200-275-002.813”� 3200-281-003.813”� 3200-381-00

FMSR RUNNING TOOL

SIZE PART NUMBER1.710”� 3205-171-001.781”� 3205-178-002.125”� 3205-212-002.188”� 3205-218-002.562”� 3205-256-003.688”� 3205-368-00

FMSX RUNNING TOOL

FMSR RUNNING TOOL

B SHIFTING TOOL

The FMS Type “B” Shifting Tool is used to position the closing sleeve or sliding

side door to the open or closed position.

“B” SHIFTING TOOL

SIZE PART NUMBER1.781”� 3250-178-001.875”� 3250-187-002.125”� 3250-212-002.313”� 3250-231-002.562”� 3250-256-002.750”�2.813”� 3250-275-003.812”� 3250-381-00


B SHIFTING TOOL

FMS SELECTIVE SHIFTING TOOL

SIZE 1.875" 2.313" 2.750-2.813"PART NUMBER 3270-187-00 3270-231-00 3270-275-00

B SHIFTING TOOL

B SHIFTING TOOL

FMSS LOCK STANDING VALVE

WITH KOBE KNOCKOUT

EQUALIZING SUB

TYPE A STANDING VALVE TYPE “A” STANDING VALVE

The FMS Type “A” Standing Valve is designed to hold pressure from above,

preventing downward flow of well fluids while allowing upward flow. The Type

“A” Standing Valve locates and seals in the FMS Type “A” Seating Nipple. The

Standing Valve is designed to allow the pressure differential to be equalized

before it is removed from the seating nipple.

TYPE “A” STANDING VALVE

NOMINAL SIZE 1 1/2” 2” 2 1/2” 3”PART NUMBER 3320-150-00 3320-200-00 3320-250-00 3320-300-00

FMSS LOCK STANDING VALVE

WITH KOBE KNOCKOUT EQUALIZING

SUB

FMSS Lock Standing Valves are designed for

use with the FMSS Locking Mandrel. A “Kobe”

Knockout Type Equalizing Sub is adapted to this

assembly allowing equalization of pressure

before the assembly is removed from the well.

FMSS LOCK STANDING VALVEWITH KOBE KNOCK OUT EQUALIZING SUB

NOMINAL SIZE 2” 2 1/2” 3”PART NUMBER 3330-200-00 3330-250-00 3330-300-00

TYPE A STANDING VALVE

FMSS LOCK STANDING VALVE WITH KOBE KNOCK

OUT EQUALIZING SUB

STEM (WEIGHT BAR)

STEM (WEIGHT BAR)

FMS Wireline Stems, often referred to as weight bars provide the mass required

in jarring operations and the mass required to enable the tool string to “fall” against

the tubing differential pressure and friction at the wireline stuffing box.

Stems are essentially round rods provided with pin and a fishing neck at one end

and a box connection at lower end.

STEM (WEIGHT BAR)





1”� 1.000”� 3350-100-02 3350-100-03 3350-100-051 1/4”� 1 3/16”� 3350-125-02 3350-125-03 3350-125-051 1/2”� 1 3/8”� 3350-150-02 3350-150-03 3350-150-051 3/4”� 1 3/4”� 3350-175-02 3350-175-03 3350-175-051 7/8”� 1 3/4”� 3350-187-02 3350-187-03 3350-187-052 1/8”� 1 3/4”� 3350-212-02 3350-212-03 3350-212-05


STEM (WEIGHT BAR)

ROLLER STEM ROLLER STEM

The FMS Roller Stem is a specially designed tool used in the wireline tool

string to minimize the effect of friction caused by the tool string sliding on the

tubing wall in highly deviated wells.

FMS Roller Stem consist of a standard three foot length stem with four slots to

accommodate simple disc rollers.

LEAD FILLED STEMS

FMS Lead Filled Stems are used instead of conventional stems when additional

weight per foot on given o.d. is required.

The Lead Filled Stem consists of a top sub with fishing neck and pin thread, a

tube into which lead is poured, and a bottom sub with a box connection.

LEAD FILLED STEM





1”� 1.000”� 3355-100-02 3355-100-03 3355-100-051 1/4”� 1 3/16”� 3355-125-02 3355-125-03 3355-125-051 1/2”� 1 3/8”� 3355-150-02 3355-150-03 3355-150-051 3/4”� 1 3/4”� 3355-175-02 3355-175-03 3355-175-051 7/8”� 1 3/4”� 3355-187-02 3355-187-03 3355-187-05


ROLLER STEM WITH TEFLON WHEELS




1 1/4”� 1 3/16”� 3360-125-03 3360-125-051 1/2”� 1 3/8”� 3360-150-03 3360-150-051 3/4”� 1 3/4”� 3360-175-03 3360-175-051 7/8”� 1 3/4”� 3360-187-03 3360-187-05


ROLLER STEM WITH TEFLON WHEELS

LEAD FILLED STEM

G TUBING STOP

TYPE G TUBING STOP

The FMS Type “G” Tubing Stop is designed

to anchor the Type “G” Pack Off Assembly in

a tubing string to straddle and pack off a hole

or other communications in the tubing.

TYPE A TUBING STOP

The FMS Type “A” Tubing Stop is designed

to set in the tubing when a collar stop cannot

be used for various wireline operations. The

Type “A” Tubing Stop can also be used as an

anchor stop or to hold down pack off as-

sembles set in tubing.

TYPE A TUBING STOP

TYPE A TUBING STOP

NOMINAL SIZE 2" 2 1/2" 3"PART NUMBER 3380-200-00 3380-250-00 3380-300-00MINIMUM I.D. .687" 1.046" 1.531"FISHING NECK O.D. 1.375" 1.750" 2.312"


TYPE G TUBING STOP

NOMINAL SIZE 2" 2 1/2" 3"PART NUMBER 3395-200-00 3395-250-00 3395-300-00MINIMUM I.D. 1.06" 1.50" 2.00"FISHING NECK I.D. 1.375" 1.812" 2.312"

TYPE A TUBING STOP

TYPE G TUBING STOP

TYPE F COLLAR STOP

The FMS Type “F” Collar Stop is designed to locate and set in tubing coupling

recesses. The Type “F” Collar Stop is used to prevent tools from falling through

the tubing and into the casing and is applicable for a wide range of wireline

operations.

TYPE 2” – 2 1/2”�COLLAR STOP

3”�COLLAR STOP

PART NUMBER 3130-000-12 3130-000-13

COLLAR STOP RUNNINGTOOL

TYPE F COLLAR STOP

TYPE F COLLAR STOP

NOMINAL SIZE 2" 2 1/2" 3"PART NUMBER 3400-200-00 3400-250-00 3400-300-00MINIMUM I.D. .875" 1.125" 1.625"FISHING NECK O.D. 1.375" 1.750" 2.312"


TYPE F COLLAR STOP

FMS STUFFING BOXSTUFFING BOX

The FMS Stuffing Box is used while performing wireline operations

with slickline under pressure. The wireline is passed over the sheave

wheel and fed down through packing in the stuffing box body. During

operation the packing is tightened against the wireline to seal off the

well pressure. The Stuffing Box is adjusted by a packing nut which is

either manually or hydraulically operated.

The FMS Stuffing Box incorporates a “blow out” plug that will auto-

matically seal and contain the well pressure in the event of the wireline

breaking or being detached from the rope socket.

The Stuffing Box includes a pin section quick union connection and is

positioned on top of the lubricator assembly.

SPECIFY STANDARD OR H2S SERVICE WHEN ORDERING

SPECIFY QUICK UNION TYPE WHEN ORDERING

FMS STUFFING BOX

DESCRIPTION PART NUMBER5000 PSI W.P. ASSEMBLYLESS STAFF 3430-000-0010,000 PSI W.P. ASSEMBLYLESS STAFF 3435-000-0015,000 PSI W.P. ASSEMBLYLESS STAFF 3440-000-00

HYDRAULIC PACKING NUT

STAFF ASSEMBLY FOR FMS STUFFING BOX

DESCRIPTION PART NUMBER7" SHEAVE ASSEMBLY 3450-007-0010" SHEAVE ASSEMBLY 3450-010-0016" SHEAVE ASSEMBLY 3450-016-00


DESCRIPTION PART NUMBERASSEMBLY 3460-000-00

FMS STUFFING BOX


TYPE N TEST TOOL

TYPE “N” TEST TOOL

The FMS Type “N” Test Tool is used to pressure test the tubing string. The

Type “N” Test Tool locates and seals in a No-Go type nipple.

Once the “N” Test Tool is located in the nipple, test pressure from above will

seat the top sub of the Test Tool, plugging the tubing string. The packing on the

body of the test tool seals in the polished bore of the nipple. When test pressure

is removed, the top sub is free to move off seat to allow equalization of pres-

sure across the bottom of the Test Tool.

TYPE S TEST TOOL

TYPE “S” TEST TOOL

The FMS Type “S” Test Tool is similar in design

to the Type “N” Test Tool, except it incorporates

the use of the FMSS Locator Mandrel Assembly.

This allows the tubing string to be tested above

the landing nipple selected.

TYPE S TEST TOOL

SIZE PART NUMBER 2”� 3535-200-00 2 1/2”� 3535-250-00 3”� 3535-300-00

TYPE N TEST TOOL

SIZE PART NUMBER1.875”� 3530-187-002.313”� 3530-231-002.750”� 3530-275-002.875”� 3530-287-00

TYPE S TEST TOOL

TUBING END LOCATOR

TUBING SWEDGE

TUBING END LOCATOR

The FMS Tubing End Locator is used to locate the lower end of the tubing so

that its depth may be accurately measured.

The Tubing End Locator consists of a slotted body in which a spring-loaded

latch is retained. A shear pin limits the outward travel or rotation of the latch.

When the tool emerges from the lower end of the tubing, the latch will be

stopped in a position that is approximately perpendicular to the body and can

not re-enter the tubing until the shear pin is cut.

TUBING SWEDGE

The FMS Tubing Swage is used to swage out mashed areas and other obstruc-

tions in the tubing string to insure the free passage of the subsurface controls. It

is also used to open orange-peel type bull plugs on the lower end of the tubing.

The FMS Tubing Swage is tapered on both ends. The upper end is threaded

with a pin connection and a fishing neck. Since the largest portions of the

swage is approximately equal to the drift diameter of the tubing, a fluid course

is provided through the central bore and lateral ports.

TUBING SWEDGE



1.250”� 15/16” – 10 UN PIN 1 3/16”� 3580-125-00 1.500”� 15/16” – 10 UN PIN 1 3/16”� 3580-150-00 1.750”� 15/16” – 10 UN PIN 1 3/16”� 3580-175-00 1.843”� 15/16” – 10 UN PIN 1 3/8”� 3580-184-00 1.906”� 15/16” – 10 UN PIN 1 3/8”� 3580-190-00 2.250”� 15/16” - 10 UN PIN 1 3/8”� 3580-225-00 2.343”� 15/16” – 10 UN PIN 1 3/8”� 3580-234-00 2.500”� 15/16” – 10 UN PIN 1 3/8”� 3580-250-00 2.750”� 1 1/16” – 10 UN PIN 1 3/4”� 3580-275-00 2.875”� 1 1/16” – 10 UN PIN 1 3/4”� 3580-287-00 OTHER SIZES AVAILABLE ON REQUEST

TUBING END LOCATOR

SIZE – O.D. 1 1/4” 1 1/2” 1 3/4”PART �NUMBER� 3570-125-00� 3570-150-00� 3570-175-00�

� �OTHER �SIZES �AVAILABLE � ON �REQUEST�

PINEAPPLE BROACH

TUBING BROACHING TOOL

The FMS Broaching Tool is a wireline service

tool designed to remove excess cement, salt,

barium, or other deposits that have accumulated

on the tubing wall, restricting the I.D. and flow

area.

The FMS “Pineapple” Broaching Tool offers a

superior cutting area covering the full drift

diameter of the tubing while allowing by-pass

area for effective broaching operations.

DIAMOND BROACH

WIREFINDERWITH TOP SUB

WIREFINDER

The FMS Wirefinder (two pieces) is a wireline tool designed to locate and ball

the broken end of the wireline in the well bore during wireline fishing operations.

The FMS Wirefinder is a two piece tool, consisting of a top sub with a standard

fishing neck and pin connection, and a slotted skirt.

WIREFINDER

SPLIT SKIRTWIREFINDER TOP SUB

WITH CENTER MANDREL

WIREFINDER

SIZE – O.D. PART NUMBER 1.593”� 3605-159-00 1.843”� 3605-184-00 2.160”� 3605-216-00 2.250”� 3605-225-00 2.700”� 3605-270-00 2.843”� 3605-284-00TOP SUB 3610-000-01TOP SUB W/CENTERMANDREL

3610-000-02


SPLIT SKIRT

CENTER SPEARWIRELINE GRAB WIRELINE GRAB

The FMS Wireline Grab is a wireline service

tool normally used to retrieve wireline that has

broken in the well bore.

The Wireline Grab has flexible legs with

pointed barbs inside each leg to form hooks that

will catch the looped end of the broken wireline.

CENTER SPEAR

The FMS Center Spear is a wireline service tool

used to fish out broken wireline from the well

bore. If the ball of wire is too compacted

making it impossible to use a conventional

wireline grab, this tool is used to pierce the ball

of wire, loosen the wire and retrieve it from the

well bore.

WIRELINE GRAB

SIZEMAX. O.D.

PART NUMBER 2 PRONG

PART NUMBER 4 PRONG

1.500”� 3620-150-00 3625-150-00 1.750”� 3620-175-00 3625-175-00 2.250”� 3620-225-00 3625-225-00 2.500”� 3620-250-00 3625-250-00 2.625”� 3620-262-00 3625-262-00 2.700”� 3620-270-00 3625-270-00


CENTER SPEAR


WIRELINE GRAB

CENTER SPEAR

TREE CONNECTION

TUBING PIN X QUICK UNION

THREADED HALF

TREE CONNECTION

FMS Tree Connections are designed to screw in to the top of the wellhead, enabling wireline and other well service

operations to be performed through the wellhead and into the well bore. Tree Connections are available with tubing

pin connections or other wellhead connections, with a quick union connection to allow the wireline surface equipment

to be installed on the wellhead.

WELLHEAD FLANGE ADAPTER

WELLHEAD FLANGE ADAPTER

The FMS Wellhead Flange Adapter is designed to be used

on top of A.P.I. Wellheads and therefore enable wireline and

other well service operations to be performed through the

wellhead and into the well bore.

The bore through the Wellhead Flange Adapter should

always be compatible with the bore through the wellhead

upon which it is to be flanged.

The Wellhead Flange Adapter is constructed with appropiate

quick union connections, enabling the wireline surface

equipment to be installed on the wellhead.

Other Wellhead Adapters or threaded connections are also

available with quick unions.

SPECIFY STANDARD SERVICE OR H2S SERVICE WHEN

ORDERING.

ALL FLANGES ARE MANUFACTURED TO API SPECIFICA-

TIONS.

SPECIFY QUICK UNION TYPE WHEN ORDERING.

HYDRAULIC JAR

The Hydraulic Jar is a wireline service tool designed for dependable, controlled

upward jarring when required during wireline operations. A closed hydraulic

system permits the operator to control the intensity of the jarring. The Hydraulic

Jar can be made to deliver a light impact when being used with slickline, or it can

be adjusted to deliver a heavy impact, as might be required when used with a

braided line.

SIDEWALL CUTTER

The Sidewall Cutter is a type of wireline cutter run with the tool string and can be

set out at any point in the tubing. The knives overlap a tapered mandrel that cuts

the line against the tubing wall. The line can be cut and retrieved in segments, thus

reducing the possibility of two lines becoming entangled in the tubing, especially

in deviated wells.

WIRELINE SNIPPER

Wireline Snippers are available in different sizes and are used to cut .092", .108"

and other size wirelines at the rope socket when the downhole tools have become

stuck. Wireline Snippers to cut 3/16" or 7/32" braided lines are also available.

SINGLE - LINE HYDRAULIC WEIGHT INDICATOR

Single Line wireline weight indicators provide reliable indications of downhole

tool weight during wireline operations.

Weight indicators are available in 0 - 2000 lb or 0 - 4000 lb capacities.

SIDEWALL CUTTER

2003 fm scat

Documents