2006 volvo xc90 (1)

2006 VOLVO XC90

https://www.customers.volvocars.com/owners/docs/2006/2006_XC90/06xc90_00.htm[8/9/2009 5:27:53 PM]

2 0 0 6 VOLVO

XC90

Introduction

Welcome to the world-wide family of Volvo owners. We trust that you will enjoy many years of safe driving in yourVolvo, an automobile designed with your safety and comfort in mind. To help ensure your satisfaction with thisvehicle, we encourage you to familiarize yourself with the equipment descriptions, operating instructions andmaintenance requirements/recommendations in this manual. We also urge you and your passengers to wear seat beltsat all times in this (or any other) automobile. And, of course, please do not operate a vehicle if you may be affected byalcohol, medication or any impairment that could hinder your ability to drive. Your Volvo is designed to meet all applicable safety and emission standards, as evidenced by the certification labelsattached to the driver's door opening and on the left wheel housing in the engine compartment.

For further information please contact your retailer, or: In the USA: Volvo Cars of North America Customer Care Center P.O. Box 914 Rockleigh, New Jersey 07647-09141-800-458-1552 http://www.volvocars.usIn Canada: Volvo Cars of Canada Ltd.National Customer Service175 Gordon Baker RoadNorth York, Ontario M2H 2N71-800-663-8255 http://www.volvocanada.com

http://www.volvocars.us/

http://www.volvocanada.com/

2006 VOLVO XC90


2005 © Volvo Cars of North America, LLC

General information

Shiftlock (automatic transmission)When your vehicle is parked, the gear selector is locked in the (P)ark position. To release the selector from thisposition, turn the ignition key to position II (or start the engine), depress the brake pedal, press the button on the frontside of the gear selector and move the selector from (P)ark.

Keylock (automatic transmission) When you switch off the ignition, the gear selector must be in the (P)ark position before the key can be removed fromthe ignition switch.

Anti-lock Brake System (ABS) The ABS system in your vehicle performs a self-diagnostic test when the vehicle first reaches the speed ofapproximately 12 mph (20 km/h). The brake pedal will pulsate several times and a sound may be audible from theABS control module. This is normal.

Fuel filler doorThe fuel filler door, located on the right rear fender, is connected to your vehicle's central locking system.Press the button on the light switch panel (see illustration on page 29) when the vehicle is at a standstill to unlock thefuel filler door. Please note that the fuel filler door will remain unlocked until the vehicle begins to move forward. Anaudible click will be heard when the fuel filler door relocks.

Fuel filler capAfter refueling, close the fuel filler cap by turning it clockwise until it clicks into place. If this cap is not closed tightlyor if the engine is running when the vehicle is refueled, the Malfunction Indicator Lamp ("Check Engine" light) willilluminate.

Important information Before you operate your vehicle for the first time, please familiarize yourself with the new engine oil consumptioninformation on page 86. You should also be familiar with the information in chapters one, two and eight of thismanual.

Information contained in the balance of the manual is extremely useful and should be read after operating the vehiclefor the first time.

The manual is structured so that it can be used for reference. For this reason, it should be kept in the vehicle for readyaccess.

Do not export your Volvo to another country before investigating that country's applicable safety and exhaust emissionrequirements. In some cases it may be difficult or impossible to comply with these requirements. Modifications to theemission control system(s) may render your Volvo not certifiable for legal operation in the U.S., Canada and othercountries.

All information, illustrations and specifications contained in this manual are based on the latest product informationavailable at the time of publication. Please note that some vehicles may be equipped differently, depending on speciallegal requirements. Optional equipment described in this manual may not be available in all markets.

Volvo reserves the right to make model changes at any time, or to change specifications or design without notice andwithout incurring obligation.

2006 VOLVO XC90


WARNING! CALIFORNIA Proposition 65 WarningEngine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to thestate of California to cause cancer, and birth defects or other reproductive harm. In addition, certain fluids containedin vehicles and certain products of component wear contain or emit chemicals known to the State of California tocause cancer, and birth defects or other reproductive harm.

Volvo and the environment

Volvo is committed to the well being of its customers. As a natural part of this commitment, we care about theenvironment in which we all live. Caring for the environment means an everyday involvement in reducing ourenvironmental impact.

Volvo's environmental activities are based on a holistic view, which means we consider the overall environmentalimpact of a product throughout its complete life cycle. In this context, design, production, product use, and recyclingare all important considerations.

In production, Volvo has partly or completely phased out several chemicals including chlorofluorocarbons (CFCs),lead chromates, naphtanates, asbestos, mercury and cadmium; and reduced the amount of chemicals used in our plants50% since 1991.

Volvo was the first in the world to introduce into production a three-way catalytic converter with Lambda Sond, nowcalled oxygen sensor, in 1976. The current version of this highly efficient system reduces emissions of harmfulsubstances (CO, HC, NOx) from the exhaust pipe by approximately 95% and the search to eliminate the remainingemissions continues. Volvo is the only automobile manufacturer to offer CFC-free retrofit kits for the air conditioningsystem of all models as far back as the 1975 Volvo 240. Advanced electronic engine controls, refined purificationsystems and cleaner fuels are bringing us closer to our goal.

After Volvo vehicles and parts have fulfilled their use, recycling is the next critical step in completing the life cycle.The metal content is about 75% of the total weight of a vehicle, which makes the vehicle among the most recycledindustrial products. In order to have efficient and well controlled recycling, many Volvo variants have printeddismantling manuals, indicating the weight and material of individual components. For Volvo, all homogeneous plasticparts weighing more than 1.7 oz. (50 grams) are marked with international symbols that indicate how the component isto be sorted for recycling.

In addition to continuous environmental refinement of conventional gasoline-powered internal combustion engines,Volvo is actively looking at advanced technology alternative-fuel vehicles.

When you drive a Volvo, you become our partner in the work to lessen the vehicle's impact on the environment.

To reduce your vehicle's environmental impact, you can:

Maintain proper air pressure in your tires. Tests have shown decreased fuel economy with improperly inflated tires. Follow the recommended maintenance schedule in your Warranty and Service Records Information booklet. Drive at a constant speed. See an authorized Volvo retailer as soon as possible for inspection if the check engine (malfunction indicator) lamp

illuminates, or stays on after the vehicle has started. Properly dispose of any vehicle-related waste such as used motor oil, used batteries, brake pads, etc. When cleaning your vehicle, use Volvo's own vehicle care products, all of which have systematically been adapted

to the environment.

For additional information regarding the environmental activities in which Volvo Cars of North America, LLC andVolvo Car Corporation are involved, visit our Internet home page at:

2006 VOLVO XC90


http://www.volvocars.us

PremAir®

On the surface of the radiator in the engine compartment, there is a special coating called PremAir®. PremAir® worksas a catalytic converter, converting most of the ground-level ozone passing through the radiator into oxygen, therebyreducing harmful ground-level ozone.

PremAir is a registered trademark of Engelhard Corporation.

Instruments, switches and controls

Control panel in driver's door (controls 34-37)

1. Headlights/Parking lights 292. Instrument lighting 293. Panel vents 524. Text window 265. Temperature gauge 22


2006 VOLVO XC90


6. Odometer/Trip odometer/Cruise control indicator 22, 387. Speedometer iv8. Turn signal indicator lights 229. Tachometer 2210. Ambient temperature gauge, clock, gear indicator 2211. Fuel gauge 2212. Indicator and warning symbols 2313. Panel vents 5214. Glove compartment 6915. Hazard warning flashers 3616. Audio system 18317. Switches in the center console 2718. Climate system controls 5319. Windshield wiper/washer lever 3320. Audio control buttons in steering wheel 18521. Instrument panel 2222. Horn iv23. Cruise control buttons in steering wheel 3824. Turn signals, High/low beams 3225. Front fog lights, Rear fog light 2926. Parking brake pedal 4127. Parking brake release handle 4128. Button for unlocking fuel filler door 2929. Hood open lever 4130. Reading lights 6531. Courtesy light 6532. Moonroof control (option) 4633. Seat belt reminder 2534. Rearview mirror 4435. Central locking button 7936. Lockout switch for rear seat power windows 4337. Power window controls 4238. Sideview mirror controls 44

WARNING! If your vehicle is involved in an accident, unseen damage may affect your vehicle's driveability and safety.

Contents

ContentsSafety

Instruments and controls

Climate control

Interior

Locks and alarm

Starting and driving

2006 VOLVO XC90


Wheels and tires

Vehicle care

Maintenance

Specifications

Audio

Index

Back Cover

Top of Page

2006 VOLVO XC90

https://www.customers.volvocars.com/owners/docs/2006/2006_XC90/06xc90_02a.htm[8/9/2009 5:27:58 PM]

2 0 0 6 VOLVO

XC90

Instruments and controls

pg. 21 Instruments and controls

Instrument panel 22

Indicator and warning symbols 23

Switches in center console 27

Lighting panel 29

Manually unlocking the fuel filler door 30

Steering wheel adjustment 31

Left-side steering wheel lever 32

Right-side steering wheel lever 33

Tailgate wiper/washer 35

Hazard warning flashers, rear window/sideview mirror defroster, heated front seats 36

Trip computer (option) 37

Cruise control 38

Opening the tailgate, Auxiliary 12-volt sockets 40

Parking brake, Opening/closing the hood 41

Electrically operated windows 42

Rearview mirror/power folding sideview mirror 44

Power moonroof (option) 46


Instrument panel

2006 VOLVO XC90


1. Turn signal indicators - right - left

2. Text windowThe text window displays information and warning messages.

3. Temperature gaugeThe pointer should be approximately midway on the gauge when driving. Do not drive the vehicle if the warninglight is on. The text window will provide you with additional information. If the engine temperature remains high,check coolant level - see page 146.

4. Trip odometerThe trip odometers are used for measuring shorter distances. The right-hand digit gives tenth of a mile/kilometer. Pressthe button for more than 2 seconds to reset. Change between trip odometers 1 and 2 using one short press on thebutton.

5. Odometer

6. Speedometer

7. Warning symbol

8. High beam indicator

9. TachometerThe tachometer shows engine speed in thousands of revolutions per minute (rpm). Do not drive continuously with theneedle in the red area of the dial, which indicates maximum allowable engine rpm range. Instead, shift to a higher gearor slow the vehicle down. The engine management system will automatically prevent excessively high engines speeds.This will be noticeable as a pronounced unevenness in engine speed.

10. Gear and driving mode indicatorThe currently selected driving mode is displayed here. If you use the Geartronic function on the automatictransmission, the currently selected gear will be displayed.

11. Ambient temperature gaugeThis display indicates the air temperature outside your vehicle. A "snowflake" symbol in the text window is displayedwhen the temperature is in the range of 23 - 36° F (-5 - +2° C). Please note that this symbol does not indicate a faultwith your vehicle. At low speeds or when the vehicle is not moving, the temperature readings may be slightly higherthan the actual ambient temperature.

12. Clock/set buttonTurn the button to set the clock.

13. Fuel gaugeThe fuel tank holds approximately 21.1 US gals. (80 liters).

2006 VOLVO XC90


When a warning light in the gauge comes on, there are approximately 2.1 US gal. (8 liters) of fuel remaining in thetank.

14. Indicator and warning symbols


Indicator and warning symbols

The indicator and warning symbols light up when you turn the ignition key to the driving position (position II) beforestarting. This shows that the symbols are functioning. When the engine starts, all symbols go out. If the engine is notstarted within 5 seconds, all symbols except CHECK ENGINE and go out. The symbol for the parking brakegoes out when the parking brake is released.

Warning symbol in center of instrument panelThis symbol shines as a red or yellow light depending on the severity of the fault that has been detected.

Red symbol -Stop the vehicle as soon as possible in a suitable location and read the message shown in the textwindow. The symbol and accompanying text will remain on until the fault has been corrected.

Yellow symbol -Follow the instructions shown in the text window. The text can be erased by pressing the READbutton (see page 26), or will disappear automatically after two minutes. NOTE: When the message "TIME FOR REGULAR SERVICE" is displayed, the text can be erased and the yellowsymbol light can be turned off by pressing the READ button. The text will disappear and the symbol light will go outautomatically after two minutes.

Anti-lock brake system ABS

If the warning light comes on, there is a malfunction of the ABS system (the standard braking system will stillfunction). The vehicle should be driven to a Volvo retailer for inspection. See page 97 for additional information.


Indicator and warning symbols (contd)

BRAKE Brake failure warning lightIf the light comes on while driving or braking, stop immediately, open the hood and check the brake fluid level in thereservoir. See page 147 for reservoir position and page 151 for instructions.

Canadian models are equipped with this warning light.

2006 VOLVO XC90


If the BRAKE and ABS warning lights come on at the same time, this could indicate a fault in the brake system.

Stop the vehicle in a suitable place and switch off the engine.Restart the engine.If both warning lights go off, no further action is required.If both lights are still on after the engine has been restarted, switch off the engine again and check the brake fluid

level (see page 147 for the location of the brake fluid reservoir).

WARNING!The If the fluid level is below the MIN mark in the reservoir or if a "Brake failure - Service urgent" message isdisplayed in the text window: DO NOT DRIVE. Have the vehicle towed to an authorized Volvo retailer and havethe brake system inspected.

If the brake fluid level is above the MIN mark, drive carefully to an authorized Volvo retailer and have the brakesystem inspected.

DSTCThe Dynamic Stability and Traction Control system (DSTC) is explained in greater detail on pages 98 and 99.


Supplemental Restraint system (SRS)

If this light comes on while the car is being driven, or remains on for longer than approximately 10 seconds after thecar has been started, the SRS system's diagnostic functions have detected a fault in a seat belt lock or tensioner, a frontairbag, side impact airbag, and/or an inflatable curtain. Have the system(s) inspected by a trained and qualified Volvoservice technician as soon as possible.

Generator warning light

If the light comes on while the engine is running, have the charging system checked.

Seat belt reminder

This symbol lights up to indicate that the driver has not fastened his/her seat belt.

Tire pressure monitoring light

See page 117 for more information on this function.

PARKING BRAKEThis light will be on when the parking brake is applied. The parking brake pedal is located on the left side of thedriver's footwell.

2006 VOLVO XC90


Canadian models are equipped with this symbol.

Rear fog light

This light indicates that the fog light is on.

Turn signal indicator - trailer (certain models)If you are towing a trailer, this light will flash simultaneously with the turn signals on the trailer. If the light does notflash when signaling, neither the trailer's turn signals nor the vehicle's turn signals are functioning.

Oil pressure warning light

If the light comes on while driving, stop the vehicle and then stop the engine immediately and check the engineoil level See page 149. If the light stays on after restart, have the vehicle towed to the nearest authorized Volvoretailer. After hard driving, the light may come on occasionally when the engine is idling. This is normal, provided itgoes off when the engine speed is increased.

CHECK ENGINE Malfunction indicator lightOn-Board Diagnostics II (OBDII): As you drive, a computer called "OBDII" monitors your vehicle's engine,transmission, electrical and emission systems. The CHECK ENGINE light will light up if the computer senses acondition that potentially may need correcting. When this happens, please have your vehicle checked by a Volvoretailer as soon as possible.

A CHECK ENGINE light may have many causes. Sometimes, you may not notice a change in your vehicle's behavior.Even so, an uncorrected condition could hurt fuel economy, emission cleanliness, and driveability. Extended drivingwithout correcting the cause could even damage other components in your vehicle.

Canadian models are equipped with this warning light.


Indicator and warning symbols (contd)

Messages in the text windowWhen a warning light in the instrument panel comes on, a message is also displayed in the text window. After youhave read the message, you can erase it by pressing button A (see illustration).

NOTE: Certain messages cannot be erased until the condition has been corrected.

2006 VOLVO XC90


If a warning message is displayed when e.g. you are using the trip computer, this message must be erased before youcan access the function of your choice. Press button A to erase the warning message.

You can scroll through the stored messages by pressing button A (see illustration). The text window can be cleared(the message will be returned to memory) by pressing button A again.

Message Meaning:STOPSAFELY: Stop and switch off the engine - to help prevent serious risk of damage.

STOPENGINE: Stop and switch off the engine - to help prevent serious risk of damage.

SERVICEURGENT: Take your car to a trained and qualified Volvo service technician for inspection immediately.

SEEMANUAL: Refer to your owner's manual. For additional information, please contact your Volvo retailer.

SERVICEREQUIRED:

Take your car to an authorized Volvo retailer for inspection at your convenience (but preferably beforethe next scheduled maintenance service).

FIX NEXTSERVICE: Have the system affected inspected at the next scheduled maintenance.

TIME FORREGULARSERVICE

This message will be displayed at 7,500 mile (12,000 km) intervals, after 750 hours of driving or after12 months, whichever occurs first, to remind the driver that the service interval has been exceeded. Themessage will be displayed for 2 minutes each time the vehicle is started until reset by the servicingretailer.

OIL LEVELLOW - FILLOILa

Check the oil level and top up if necessary. See page 149.

OIL LEVELLOW -STOPSAFELYb

Stop as soon as possible and switch off the engine, check the oil level and top up if necessary. See page149.

OIL LEVELLOW -STOPENGINEb

Stop as soon as possible and switch off the engine, check the oil level and top up if necessary. See page149.

OIL LEVELLOW - SEEMANUALb

Stop as soon as possible and switch off the engine, check the oil level and top up if necessary.See page149.

a. The yellow warning symbol also lights up (see page 23)b. The red warning symbol also lights up (see page 23)


Switches in center console

2006 VOLVO XC90


Dynamic Stability Traction Control system (DSTC)This button is used to switch off DSTC's stability Control function. See pages 98 and 99 for additional information.

WARNING! Please be aware that the vehicle's handling characteristics may be affected if the Stability Control function isswitched off.

Rear seat air conditioning (option)This button controls the optional rear seat air conditioning system on seven-seat models.

Folding sideview mirrors (option)Press the button and release it to fold the sideview mirrors in or out. On certain models, when the button is pressed,there may be a long pause before the mirrors move.

Pressing the button again during this pause may erase your first button press. If this happens, wait ten seconds andpress the button one more time.

The mirrors cannot be adjusted during the first ten seconds after they have been folded out.

NOTE: If the sideview mirrors have been inadvertently pushed out of position (in a car wash, parking lot, etc.)manually return them to normal position. If mirror adjustment does not seem to operate after manual folding, reset thefolding mirrors as follows:

Turn the ignition key to position II. Manually fold the mirror(s) to the normal position. Press the button to fold both mirrors in. Press the button again to fold the mirrors out to their normal position.

2006 VOLVO XC90


Park Assist (option/accessory as available)This system provides an audible warning when the vehicle is being parked or if it is driven close to a person or object.See page 100 for more information.

NOTE: The system activates automatically when the engine is started, and can be deactivated by pressing this button(e.g. when towing a trailer) or reactivated if necessary.

Temporarily disconnecting the alarm sensors (option)See page 83 for more details.


Auxiliary lightsThis button is used to switch on auxiliary lights (if installed). An LED in the switch will light up to indicate that theauxiliary lights are illuminated.

12 volt socketThis 12 volt socket can be used to plug in certain accessories such as cellular telephones, etc. The ignition key must bein position 1 (or higher) for the auxiliary socket to function.

NOTE: The auxiliary sockets can also be used for cigarette lighters, which are available as accessories at your Volvoretailer.

Power child locks (option)See page 81 for more information on this function.


2006 VOLVO XC90


Lighting panel

Lighting panel 1. Headlight/parking light switch 2. Front fog lights 3. Rear fog light 4. Instrument panel lighting 5. Fuel filler door unlock button

Parking lights The front and rear parking lights can be turned on even when the ignition is switched off.

Turn switch 1 to position .

The license plate lights also illuminate when the parking lights are switched on.

Headlights

Turn the ignition key to position II.The low beam headlights (daytime running lights) illuminate automatically, except when the light switch (1) is in

position 1.

See page 32 for information on switching between high and low beams.

NOTE: Bi-Xenon headlights (option): Turn the headlight switch to position 0 to activate a daylight sensor, whichautomatically switches the low beams on or off, depending on ambient light conditions. When driving in daylight, theheadlights will switch off and the daytime running lights will come on. In darkness, the daytime running lights willswitch off and the Bi-Xenon headlights will switch on.

Foglights Front fog lights (option) The front fog lights can be used in combination with either the headlights or the parking lights.

Turn the ignition key to position II.Press button 2 to turn on the front fog lights.

An indicator light in the button illuminates when the front fog lights are on.

Rear fog light The single rear fog light is located in the driver's side tail light cluster.

2006 VOLVO XC90


The rear fog light will only function in combination with the high/low beam headlights or the optional front fog lights.

Turn the ignition key to position II.Press button 3 to turn on the rear fog light.

An indicator light in the button illuminates when the rear fog light is on.

NOTE: The rear fog light is considerably brighter than the normal tail lights and should be used only when conditionssuch as fog, rain, snow, smoke or dust reduce visibility for other vehicles to less than 500 ft. (150 meters).

Instrument panel lighting The instrument panel lighting illuminates when the ignition key is in position II and the light switch (1) is in eitherposition or .

Move the thumb wheel (4) up to increase brightness or down to decrease brightness.

Unlocking the fuel filler doorPress button 5 when the car is at a standstill to unlock the fuel filler door. Please note that the fuel filler door willremain unlocked until the car begins to move forward. An audible click will be heard when the fuel filler door relocks.

NOTE: If the fuel filler door does not unlock after the button has been pressed, drive the car

1. On Canadian models, the daytime running lights will remain on with the light switch in this position.


Manually unlocking the fuel filler door NOTE: at a speed of at least 5 mph (8 km/h), stop the car, and press the button again. See the information to the righton unlocking the fuel filler door manually.

Panel on passenger's side of cargo area

Manually unlocking the fuel filler door

1. Open the upper and lower sections of the tailgate, and fold up the rear section of the cargo area floor.

2. If the vehicle is equipped with the optional grocery bag holder, detach the holder's bands.

3. Remove the corner panel (1) from the floor of the cargo area.

4. Open the cover (2) in the side panel by pulling the tab (3) upward/outward.

2006 VOLVO XC90


5. Pull down the insulating material (4) to access the fuel filler door motor (5).

6. Move the catch (6) rearward to unlock the fuel filler door lock, or move it forward to lock the filler door.


Steering wheel adjustmentBoth the height and the reach of the steering wheel can be adjusted to a comfortable position for the driver. Pull downthe lever on the left of the steering column. Adjust the steering wheel to a suitable position and press the lever backinto place to lock the steering wheel in the new position. Check that the steering wheel is locked in the new position.

WARNING!The Never adjust the steering wheel while driving.


Left-side steering wheel lever

Lever positions

2006 VOLVO XC90


1. Turn signals, lane change position 2. Turn signals, position for normal turns 3. High beam flash 4. Toggle between high and low beams, Home Safe lighting

Turn signals When turning Move the lever as far up or down as possible (to position 2) to start the turn signals. The turn signals will be cancelledautomatically by the movement of the steering wheel, or the lever can be returned to its initial position by hand.

When changing lanes The driver can flash the turn signals by moving the turn signal lever up or down to position 1 and releasing it. The turnsignals will flash until the lever has been released.

NOTE: If the turn signal indicator flashes faster than normal, check for a burned-out turn signal bulb.

High/low beam headlights Continuous high beams

Turn the ignition key to position II.With the light switch (1) in position , (see page 29) pull the turn signal lever toward the steering wheel

(position 4) to toggle between high and low beams (this also applies on models equipped with the optional Bi-Xenonheadlights).

High beam flash

Turn the ignition key to position II.Pull the turn signal lever to position 3. The high beams will remain on until the lever is released.

Home safe lighting When you leave your car at night, you can make use of the home safe lighting function to illuminate the area in frontof the car.

Remove the key from the ignition switch.Pull the direction indicator lever as far as possible towards the steering wheel (to position 4) and release it.Exit the car and lock the doors.

The headlights and parking lights will illuminate and remain on for 301, 60 or 90 seconds. The time interval can bechanged by an authorized Volvo retailer.

1. Factory setting


Right-side steering wheel lever

2006 VOLVO XC90


Windshield wipers

Windshield wipers off

If the lever is in the 0 position and you move it upwards, the wipers will sweep one stroke at a time for as long as youhold the lever up.

"Single sweep" positionMove the lever slightly upward from the 0 position for one sweep of the wipers. The lever return automatically to 0when released.

Intermittent wiper functionWith the lever in this position, you can set the wiper interval by twisting ring (1) upward to increase wiper speed ordownward to decrease the speed.

Rain sensor (option)The rain sensor automatically regulates wiper speed according to the amount of water on the windshield.The sensitivity of the sensor can be adjusted by twisting ring 1 up (the wipers will sweep the windshield morefrequently) or down (the wipers will sweep the windshield less frequently).

Activating the rain sensor :1. Turn the ignition key to at least position I and put the windshield wiper lever in position 0.2. Press button 2. An LED in the button will light up to indicate that the rain sensor is active.

Deactivating the rain sensor:

Press button 2. or Move the windshield wiper lever down to another position.

Moving the lever up will not deactivate the rain sensor. Doing so will cause the wipers to sweep the windshield untilthe lever is released, at which time the wipers return to rain sensor mode.

The rain sensor is also deactivated when the key is removed from the ignition.

CAUTIONThe rain sensor should be deactivated when washing the car in an automatic car wash, etc. If the rain sensor functionis left on, the wipers will start inadvertently in the car wash and could be damaged.

Continuous wiper function

Wipers operate at "high" speed


2006 VOLVO XC90


Windshield washer/headlight washer (certain models)Pull the lever toward you and release it. High pressure jets mounted in the bumper will spray the headlights.

CAUTIONUse ample washer fluid when washing the windshield to avoid scratching the glass.

NOTE:

To conserve washer fluid in driving conditions where the windshield washers are used frequently, the headlightswill only be washed once for every five times the windshield is washed within a 10- minute period.

When approximately 1 US quart (1 liter) remains in the washer fluid reservoir, the rear window and headlights willnot be washed when the lever is pulled to conserve washer fluid for the windshield.

Contents | Top of Page

2006 VOLVO XC90


2 0 0 6 VOLVO

XC90

Starting and driving

pg. 85 Starting and driving

Refueling 86

Starting the vehicle 89

General information 91

Automatic transmission with Geartronic 93

All Wheel Drive 95

Brake system 96

Dynamic Stability Traction Control (DSTC) 98

Park assist 100

Towing 101

Jump starting 103

Towing a trailer 104

Detachable trailer hitch - installing/removing 106

Load carriers 107

Cold weather precautions 108

Before a long distance trip 109


Refueling

ENGINE OILAlthough some oil consumption occurs during normal engine operation, more oil is consumed when the engine is newas the internal parts generate higher friction while wearing-in to each other. From the time the engine is new until thefirst maintenance is performed, the oil consumption could be higher than normal. For this reason, it is especiallyimportant to check the oil every time you refuel your vehicle during this period. See page 149.

Fuel requirementsOctane ratingVolvo engines are designed for optimum performance on unleaded premium gasoline with an AKI octane rating of 91

2006 VOLVO XC90


or above. AKI (ANTI KNOCK INDEX) is an average of the Research Octane Number, RON, and the Motor OctaneNumber, MON. ((RON + MON)/2). The minimum octane requirement is AKI 87 (RON 91).

Deposit control gasoline (detergent additives)Volvo recommends the use of detergent gasoline to control engine deposits. Detergent gasoline is effective in keepinginjectors and intake valves clean. Consistent use of deposit control gasolines will help ensure good driveability andfuel economy. If you are not sure whether the gasoline contains deposit control additives, check with the servicestation operator.

NOTE: Volvo does not recommend the use of external fuel injector cleaning systems.

Unleaded fuelEach Volvo has a three-way catalytic converter and must use only unleaded gasoline. U.S. and Canadian regulationsrequire that pumps delivering unleaded gasoline be labelled "UNLEADED". Only these pumps have nozzles which fityour vehicle's filler inlet. It is unlawful to dispense leaded fuel into a vehicle labelled "unleaded gasoline only".Leaded gasoline damages the three-way catalytic converter and the heated oxygen sensor system. Repeated use ofleaded gasoline will lessen the effectiveness of the emission control system and could result in loss of emissionwarranty coverage. State and local vehicle inspection programs will make detection of misfueling easier, possiblyresulting in emission test failure for misfueled vehicles.

NOTE: Some U.S. and Canadian gasolines contain an octane enhancing additive called methyl-cyclopentadienylmanganese tricarbonyl (MMT). If such fuels are used, your Emission Control System performance may be affected,and the Check Engine Light (malfunction indicator lamp) located on your instrument panel may light. If this occurs,please return your vehicle to an authorized Volvo retailer for maintenance.

Gasoline containing alcohol and ethers"Oxygenated fuels"Some fuel suppliers sell gasoline containing "oxygenates" which are usually alcohols or ethers. In some areas, state orlocal laws require that the service pump be marked indicating use of alcohols or ethers. However, there are areas inwhich the pumps are unmarked. If you are not sure whether there is alcohol or ethers in the gasoline you buy, checkwith the service station operator. To meet seasonal air quality standards, some areas require the use of "oxygenated"fuel.

Volvo allows the use of the following "oxygenated" fuels; however, the octane ratings listed on this page must still bemet.

Alcohol - Ethanol: Fuels containing up to 10% ethanol by volume may be used. Ethanol may also be referred to asEthyl alcohol, or "Gasohol".

Ethers - MTBE: Fuels containing up to 15% MTBE may be used.


Carbon Monoxide - Important WarningCarbon monoxide is a poisonous, colorless, and odorless gas. It is present in all exhaust gases. If you ever smellexhaust fumes inside the vehicle, make sure the passenger compartment is ventilated, and immediately return thevehicle to your retailer for correction.

Fuel FormulationsDo not use gasoline that contains lead as a knock inhibitor, and do not use lead additives. Besides damaging theexhaust emission control systems on your vehicle, lead has been strongly linked to certain forms of cancer.

Many fuels contain benzene as a solvent. Unburned benzene has been strongly linked to certain forms of cancer. If youlive in an area where you must fill your own gas tank, take precautions. These may include:

2006 VOLVO XC90


standing upwind away from the filler nozzle while refuelingrefueling only at gas stations with vapor recovery systems that fully seal the mouth of the filler neck during refuelingwearing neoprene gloves while handling a fuel filler nozzle.

Use of AdditivesWith the exception of gas line antifreeze during winter months, do not add solvents, thickeners, or other store-boughtadditives to your vehicle's fuel, cooling, or lubricating systems. Overuse may damage your engine, and some of theseadditives contain organically volatile chemicals. Do not needlessly expose yourself to these chemicals.


Fuel filler doorPress the button on the light switch panel (see illustration on page 29) when the vehicle is at a standstill to unlock thefuel filler door. Please note that the fuel filler door will remain unlocked until the vehicle begins to move forward. Anaudible click will be heard when the fuel filler door relocks.

If you intend to leave your vehicle while it is being refueled, this feature enables you to lock the doors/tailgate whileleaving the fuel filler door unlocked.

You can also keep the vehicle locked if you remain inside it during refueling. The central locking button does not lockthe fuel filler door.

Be sure the fuel filler door is not obstructed and is completely closed after refueling.

Open the fuel filler cap slowly during hot weather.

NOTE: During a transitional period, a small number of service stations may still have fuel nozzles that are notcompatible with the fuel filler neck on vehicles equipped with the evaporative control system.

RefuelingFuel tank capacity:The fuel tank's capacity is 21.1 US gals. (80 liters) with sufficient volume left over to accommodate possible expansionof the fuel in hot weather. Be aware that the "usable" tank capacity will be somewhat less than the specified maximum.When the fuel level is low, such factors as ambient temperature, the fuel's "Reid vapor pressure" characteristics, andterrain can affect the fuel pump's ability to supply the engine with an adequate supply of fuel. Therefore, it is advisableto refuel as soon as possible when the needle nears the red zone, or when the fuel warning light comes on.

WARNING!Never carry a cell phone that is switched on while refueling your vehicle. If the phone rings, this may cause a sparkthat could ignite gasoline fumes, resulting in fire and injury.

2006 VOLVO XC90


CAUTION- Do not refuel with the engine running *. Turn the ignition off or to position I. If the ignition is on, an incorrectreading could occur in the fuel gauge- After refueling, close the fuel filler cap by turning it clockwise until it clicks into place*.- Allow for fuel expansion by not overfilling the tank. Overfilling could also cause damage to the emission controlsystems.- Avoid spilling gasoline during refueling. In addition to causing damage to the environment, gasolines containingalcohol can cause damage to painted surfaces, which may not be covered under the New Vehicle Limited Warranty.- Do not use gasolines containing methanol (methyl alcohol, wood alcohol). This practice can result in vehicleperformance deterioration and can damage critical parts in the fuel system. Such damage may not be covered underthe New Vehicle Limited Warranty.

* If the fuel filler cap is not closed tightly or if the engine is running when the vehicle is refueled, the Check EngineLight (malfunction indicator lamp) may indicate a fault. However, your vehicle's performance will not be affected. Useonly Volvo original or approved fuel filler caps.


Starting the engine1. Fasten the seat belt.

WARNING!Before starting, check that the seat, steering wheel and mirrors are adjusted properly. Make sure the brake pedal canbe depressed completely. Adjust the seat if necessary. See pages 58, 60.

2. Apply the parking brake if not already set. The gear selector is locked in the (P)ark position (Shiftlock).Manual transmission: the clutch must be fully depressed.

3. Without touching the accelerator pedal, turn the ignition key* to the starting position. Allow the starter to operate forup to 10 seconds. Release the key as soon as the engine starts. If the engine fails to start, repeat this step.

NOTE: - On certain models, when the vehicle is started, idle speed may be noticeably higher than normal for a short period,depending on the temperature of the engine.This has been done to help bring components in the emission control system to their normal operating temperature asquickly as possible, which enables them to function normally.

- For cold starts at altitudes above 6000 ft (1800 meters), depress the accelerator pedal halfway and turn the key to thestarting position. Release the pedal slowly when the engine starts.

4. To release the gear selector from the (P)ark position, the engine must be running (or the ignition key must be inposition II) and the brake pedal must be depressed.

5. Select the desired gear. The gear engages after a very slight delay which is especially noticeable when selecting R.

NOTE: Your vehicle is equipped with a Keylock system. When the engine is switched off, the gear selector must bein the (P)ark position before the key can be removed from the ignition switch.

When starting in cold weather, the transmission may shift up at slightly higher engine speeds than normal until theautomatic transmission fluid reaches normal operating temperature.

Do not race a cold engine immediately after starting. Oil flow may not reach some lubrication points fast enough toprevent engine damage.

2006 VOLVO XC90


* If two of the keys to your vehicle are close together, e.g., on the same key ring, when you try to start the vehicle, thiscould cause interference in the immobilizer system and result in the vehicle not starting. If this should occur, removeone of the keys from the key ring before trying to start the vehicle again.

CAUTION

Automatic transmissionThe engine should be idling when you move the gear selector. Never accelerate until after you feel the transmissionengage! Accelerating immediately after selecting a gear will cause harsh engagement and premature transmissionwear.

Selecting P or N when idling at a standstill for prolonged periods of time will help prevent overheating of theautomatic transmission fluid.

WARNING!Always place the gear selector in Park and apply the parking brake before leaving the vehicle. Never leave thevehicle unattended with the engine running.Always open garage doors fully before starting the engine inside a garage to ensure adequate ventilation. Theexhaust gases contain carbon monoxide, which is invisible and odorless but very poisonous.


Starting the vehicle (cont'd)

2006 VOLVO XC90


Autostart (V8 AWD only)This function makes it possible to start the vehicle without holding the key in the start position (position III) until theengine starts. Turn the key to position III and release it. The starter motor will then operate automatically (for up to tenseconds) until the engine starts.

Steering wheel lockThe steering wheel lock might be under tension when the vehicle is parked.

Turn the steering wheel slightly to free the ignition key.

In order to help reduce vehicle theft, make sure the steering wheel lock is engaged before leaving the vehicle.

WARNING!Never switch off the ignition (turn the ignition key to position 0) or remove the key from the ignition switch whilethe vehicle is in motion. This could cause the steering wheel to lock, which would make the vehicle impossible tosteer.

* The gear selector must be in the (P)ark position (automatic transmission).** Please be aware that leaving the key in this position will increase battery drain.


General information

Economical driving conserves natural resourcesBetter driving economy may be obtained by thinking ahead, avoiding rapid starts and stops and adjusting the speed ofyour vehicle to immediate traffic conditions. Observe the following rules:

Bring the engine to normal operating temperature as soon as possible by driving with a light foot on the acceleratorpedal for the first few minutes of operation. A cold engine uses more fuel and is subject to increased wear.

Whenever possible, avoid using the vehicle for driving short distances. This does not allow the engine to reachnormal operating temperature.

Drive carefully and avoid rapid acceleration and hard braking.Use the transmission's (D)rive position as often as possible and avoid using "kickdown" to help improve fuel

economy.Do not exceed posted speed limits.Avoid carrying unnecessary items (extra load) in the vehicle.Maintain correct tire pressure. Check tire pressure regularly (when tires are cold).Remove snow tires when threat of snow or ice has ended.Note that roof racks, ski racks, etc, increase air resistance and also fuel consumption.At highway driving speeds, fuel consumption will be lower with the air conditioning on and the windows closed than

with the air conditioning off and the windows open.Using the onboard trip computer's fuel consumption modes can help you learn how to drive more economically.

Other factors that decrease gas mileage are:

Dirty air cleanerDirty engine oil and clogged oil filterDragging brakesIncorrect front end alignment

Some of the above mentioned items and others are checked at the standard Maintenance intervals.

2006 VOLVO XC90


Weight distribution affects handlingAt the specified curb weight your vehicle has a tendency to understeer, which means that the steering wheel has to beturned more than might seem appropriate for the curvature of a bend. This ensures good stability and reduces the riskof rear wheel skid. Remember that these properties can alter with the vehicle load. The heavier the load in the cargoarea, the less the tendency to understeer.

WARNING!Driving with the tailgate open: Driving with the tailgate open could lead to poisonous exhaust gases entering thepassenger compartment. If the tailgate must be kept open for any reason, proceed as follows- Close the windows- Set the ventilation system control to air flow to floor, windshield and side windows and blower control to itshighest setting.

CAUTIONDrive slowly and carefully if going through standing water (i.e. flooded roadways, etc.). Damage to the engine couldresult if excess water is drawn in through the air intake system. Never drive the vehicle in water deeper than 18inches (48 cm).


General information (contd)

Handling, roadholdingVehicle load, tire design and inflation pressure all affect vehicle handling. Therefore, check that the tires are inflated tothe recommended pressure according to the vehicle load. See "Tire pressure" section.

Loads should be distributed so that capacity weight or maximum permissible axle loads are not exceeded.

Driving on rough/unpaved surfaces The Volvo XC90 is designed primarily for onroad driving, and it has excellent handling characteristics on very roughor unpaved roads.

When driving on poorly maintained or unpaved roads, please keep the following in mind:

Reduce speed on rough surfaces to minimize possible damage to the vehicle's underbody.When driving on soft surfaces such as dry sand or snow, try to avoid stopping if at all possible.

WARNING!Avoid driving diagonally across steep inclines as this could increase the risk of a roll-over. Try to drive straight upor down the slope.If the road is very steep, avoid turning the vehicle around to help avoid the risk of rolling over. Back the vehicle upor down the incline instead.

NOTE: Avoid driving on steep inclines if the fuel tank is nearly empty. If the flow of fuel to the engine is interrupteddue to the vehicle's angle of inclination, this could result in damage to the three-way catalytic converter. Werecommend keeping the fuel tank at least half full when driving on steep inclines.

Driving through water

The vehicle should not be driven through water that is deeper than 18 inches (48 cm). Driving through deeper water

2006 VOLVO XC90


could result in damage to transmission components or the differential, or to the engine if excess water is drawn inthrough the air intake system.

Drive slowly and avoid stopping when driving through water.After having driven through water, apply the brakes lightly several times to remove water, mud, etc from the brake

discs.Never allow the vehicle to stand in water above the door sills. This could result in damage to the electrical system.

Conserving electrical currentKeep the following in mind to help minimize battery drain:

When the engine is not running, avoid turning the ignition key to position II (see page 90). Many electrical systems(the audio system, the optional infotainment/navigation systems, power windows, etc) will function with the ignitionkey in position I. This position reduces drain on the battery.

Please keep in mind that using systems, accessories, etc that consume a great deal of current when the engine is notrunning could result in the battery being completely drained.

NOTE: A warning message will be displayed in the text window in the instrument panel when the battery charge islow.


Automatic transmission with Geartronic

P ParkUse this position when starting the engine or parking the vehicle.

Never use P while the vehicle is in motion.

The parking brake should also be set whenever the vehicle is parked.

The gear selector is mechanically locked in the P position (SHIFTLOCK). To release the gear selector from thisposition, the engine must be running (or the ignition key must be in position II) and the brake pedal must bedepressed.

N (Neutral)Neutral - no gear engaged. Use the parking brake.

WARNING!Never leave the vehicle unattended when the engine is running. If, by mistake, the gear selector is moved from P, thevehicle may start moving.

2006 VOLVO XC90


R (Reverse)Never engage R while the vehicle is moving forward.

D (Drive)D is the normal driving position and should be used as often as possible to help improve fuel economy. The vehicleshould not be moving when shifting from R to the D position.

Shiftgate positions

NOTE:

5-cylinder turbo engine: 5 forward speeds.8-cylinder engine: 6 forward speeds.

Automatic transmission - shift gate positionsDepress the button on the front of the gear selector knob to move between the R, N, D, and P positions.

KickdownAutomatic shift to a lower gear (kickdown) is achieved by depressing the accelerator pedal fully and briskly. Anupshift will occur when approaching the top speed for a particular gear or by releasing the accelerator pedal slightly.Kickdown can be used for maximum acceleration or when passing at highway speeds.

NOTE: The gear selector must be in the D (Drive) position for kickdown to function.


Automatic transmission with Geartronic (contd)

Manual shifting - GeartronicYou can move the gear selector freely between the (MAN)ual and (D)rive positions while driving.

Models equipped with a 5-cylinder turbo engine have five forward speeds, and models with the V8 engine have 6forward speeds.

A "lock-up" feature 1 reduces engine speed and help saves fuel.

The currently selected gear will be displayed in the instrument panel (see page 22).

To access the (MAN)ual shifting position from (D)rive, move the gear selector to the left to MAN.To return to the (D)rive position from MAN, move the gear selector to the right.

While drivingIf you select the (MAN)ual position while driving, the gear that was being used in the (D)rive position will alsoinitially be selected in (MAN)ual position.

2006 VOLVO XC90


Move the gear selector forward (toward "+") to shift to a higher gear or rearward (toward "-") to shift to a lowergear.

If you hold the gear selector toward "-", the transmission will downshift one gear and will utilize the braking powerof the engine. If the current speed is too high for using a lower gear, the downshift will not occur until the speed hasdecreased enough to allow the lower gear to be used.

If you slow down to a very low speed, the transmission will automatically shift down.When starting in the (MAN)ual position, 3rd gear is the highest gear that may be selected.

1 Five-speed transmission: gears 3, 4, and 5Six-speed transmission: gears 2, 3, 4, 5, and 6.

5-cylinder turbo and V8 models

W - Winter/Wet driving mode - enhanced vehicle traction

Mode W will only function if the gear selector is in the (D)rive position.Press the button at the base of the gear selector to engage/disengage this driving mode (see illustration).When the W driving mode is engaged, this is displayed in the instrument panel (see page 22).

This mode may be selected for starting/moving off on slippery roads.


All Wheel Drive

All Wheel Drive (AWD) - general informationYour Volvo can be equipped with permanent All Wheel Drive (option), which means that power is distributedautomatically between the front and rear wheels. Under normal driving conditions, most of the engine's power isdirected to the front wheels. However, if there is any tendency for the front wheels to spin, an electronically controlledcoupling distributes power to the wheels that have the best traction.

Tire dimensionsVolvo recommends that you always drive on tires of the same brand, size, construction (radial), tread pattern, load-,speed-, traction-, temperature-, and treadwear rating. Never drive on mixed tires, except for brief periods when thetemporary spare tire is in use.

Always use properly inflated tires of correct dimensions. Tire size and inflation pressures are shown on the tireinflation pressure placards, located on the driver's side B-pillar (the structural member at the side of the vehicle, at therear of the driver's door opening), or on the inside of the fuel filler door on Canadian models.

Temporary SpareThe temporary spare tire is for temporary, lowspeed, short-distance use only. Replace it with a full-sized tire as soon

2006 VOLVO XC90


as possible. Do not drive on the temporary spare at speeds above 50 m.p.h. (80km/h) or for distances greater than 50miles (80 km).

Never install snow chains on a temporary spare.


2006 VOLVO XC90


2 0 0 6 VOLVO

XC90

Climate control

pg. 49 Climate control

Climate control system-general information 50

Air distribution 52

Electronic Climate Control (ECC) 53


Climate control system-general information

Condensation on the inside of the windowsKeeping the insides of the windows clean will help reduce the amount of condensation that forms on the windows. Usea commercial window cleaning agent to clean the windows.

Ice and snowAlways keep the air intake grille at the base of the windshield free of snow.

Cabin air filterReplace the cabin air filter with a new one at the recommended intervals. Please refer to your Warranty and ServiceRecords Information booklet, or consult your Volvo retailer for these intervals. The filter should be replaced moreoften when driving under dirty and dusty conditions. The filter cannot be cleaned and therefore should always bereplaced with a new one.

SensorsThe sunlight sensor on the dashboard and passenger compartment temperature sensor in the ECC control panel shouldnot be covered in any way as this could cause incorrect information to be sent to the ECC system.

Parking the vehicle in warm weatherIf your vehicle has been parked in the sun in warm weather, opening the windows and moonroof (option) for severalminutes before driving will help release the warm air from the passenger compartment. When the engine is running,close the windows and moonroof and use the recirculation function for several minutes to enable the air conditioningto cool the compartment as quickly as possible.

Windows and optional moonroofThe ECC system will function best if the windows and optional moonroof are closed. If you drive with the moonroofopen, we recommend that you manually adjust the temperature and blower control (the LED in the AUTO switchshould be off).

AccelerationThe air conditioning is momentarily disengaged during full-throttle acceleration.

2006 VOLVO XC90


Climate system maintenanceSpecial tools and equipment are required to maintain and carry out repairs on the climate system. Work of this typeshould only be done by a trained and qualified Volvo service technician.

RefrigerantVolvo cares about the environment. The air conditioning system in your vehicle contains a CFC-free refrigerant -R134a (HFC134a). This substance will not deplete the ozone layer. The system contains 2.2 lbs (1000 g) R134a anduses PAG oil.

Climate system blowerThe climate system blower will be automatically switched off when the engine is not running (even if the ignition keyis in position I or II) to avoid unnecessary battery drain. To activate the blower, turn the control to the desired setting.

Passenger compartment blowerApproximately 50 minutes after the ignition is turned off, the blower may come on automatically, and run for sevenminutes, to remove condensation in the A/C evaporator.

Blower function to reduce battery drainThe climate system's blower functions normally while the engine is running.

However, when the engine is switched off (even if the ignition is switched to positions I or II), the blower control willbe automatically switched off to avoid unnecessary battery drain.

The following points pertain if the ignition key is on but the engine is not running:

To restart the blower, turn the control knob to the setting of your choice.After approximately 2 minutes, the blower speed will be reduced to avoid battery drain.

You can reset the blower speed at any time. Please be aware that the system has been


designed to reduce the blower's speed again after 2 minutes, until the engine is started. If the battery becomes drained:

LOW BATTERY, FAN IS REDUCED will be displayed in the text window in the instrument panel.The yellow warning light in the instrument panel (see page 23) will also light up.


Air distribution

Air distribution

2006 VOLVO XC90


The incoming air is distributed through the ventilation points in the passenger compartment shown above.

Air vents in the dash

A OpenB ClosedC Horizontal air flowD Vertical air flow

Direct the outer air vents toward the side windows to defrost.

Air vents in the door pillars

A OpenB ClosedC Horizontal air flowD Vertical air flow

Direct the outer air vents toward the side windows to defrost.


Electronic Climate Control (ECC)

2006 VOLVO XC90



Electronic Climate Control (ECC) (contd)

AUTO

This function automatically regulates the Electronic Climate Control system so that the selected temperatures aremaintained. The blower, heating, air distribution (air flow) and air conditioning are controlled.If you prefer to manually set any of these functions, the remaining functions will still be controlled automatically.Pressing the AUTO button overrides any settings that were previously made manually.

Rear window and sideview mirror defrosters

This function defrosts/de-ices the rear window and sideview mirrors. The LED in the switch will light up to indicatethat the heating function is engaged. See page 36 for additional information on this function.

Never use ice scrapers made of metal as the can easily scratch the mirror surface.

Temperature

These controls are used to individually set the temperature for both sides of the passenger compartment. Please notethat the compartment will not be heated or cooled faster by setting the temperature higher or lower than necessary.

Set the control to the temperature you prefer.

2006 VOLVO XC90


Defroster

This function defrosts/de-ices the windshield and front side windows. The LED in the switch will light up to indicatethat the defrost function is engaged. Blower speed increases automatically and the air in the passenger compartment isdehumidified. Recirculation will not function while defrost is engaged.

Blower control*

Turn the control clockwise to increase or counterclockwise to decrease the blower speed. Pressing the AUTO switchwill automatically regulate blower speed and override manual adjustment.

NOTE: Turning the blower control counterclockwise until an orange LED comes on will turn both the blower and theair conditioning off.

* See also page 50.

Blower control for rear climate system (option)Turn the control to increase or decrease blower speed.


Electronic Climate Control (ECC) (contd)

Air distribution

Press AUTO to automatically regulate air flow or press any combination of the controls shown in the illustration tomanually adjust air flow. An LED in the switch will light up if an air flow control has been pressed.

Heated front seats (option)

Press the switch once for maximum seat heating. Both LEDs in the switch will be lit.Press the switch a second time for comfort heating. One LED in the switch will be lit.Press the switch a third time to turn the heating off completely. The LED will go off.

The seat heating for the passenger seat should be switched off when the seat is not occupied.

A/C - ON/OFF

2006 VOLVO XC90


Press the switch to turn the air conditioning on or off. The "ON" or "OFF" LED will light up to indicate if the systemis switched on or off. Other functions will still be regulated automatically (if the AUTO switch is on).

The air conditioning functions only at temperatures above 32° F (0° C).While the Defroster function is selected, the air conditioning is temporarily activated to dehumidify the air, even if

you have manually switched the air conditioning off. This will only function if the blower is not switched off.

Recirculation

Press this switch to engage the recirculation function (air in the passenger compartment recirculates - no fresh airenters the compartment). The LED in the switch will light up to indicate that the function is engaged.

Use this function if the outside air is contaminated with exhaust gases, smoke, etc or to heat/cool the vehicle quickly.Recirculation should not be used for more than 15 minutes. If your windows begin to fog or mist, make sure that the

recirculation function is switched off.Selecting Defroster automatically switches recirculation off.Timer mode activation: (Vehicles equipped with the Interior Air Quality System have no timer mode) Press and

hold the recirculation button for at least 3 seconds to activate a recirculation timer mode. The amber LED in therecirculation button will flash 5 times to show that the timer mode is being activated. In timer mode, each time therecirculation button is pressed, the climate control system will recirculate the air in the passenger compartment for 5-12minutes, depending on the outside air temperature, and then revert back to fresh air.

Timer mode deactivation: Press and hold the recirculation button for 3 seconds. The amber LED in the recirculationbutton will illuminate steadily for 5 seconds to show a return to "normal" mode.


In normal mode, when the recirculation button is pressed, the climate control system will recirculate the air in thepassenger compartment until the recirculation button is pressed again.

Timer mode memory: If the vehicle is turned off while timer mode is active, timer mode will still be active when thevehicle is restarted.

Interior Air Quality sensor (option)Some vehicles are equipped with a multifilter and air quality sensor. The filter separates gases and particles, therebyreducing the amounts of odors and contaminants entering the vehicle. The air quality sensor detects increased levels ofcontaminants in the outside air. When the air quality sensor detects contaminated outside air, the air intake closes andthe air inside the passenger compartment is recirculated, i.e. no outside air enters the vehicle. The filter also cleansrecirculated passenger compartment air.When the ECC system is in the AUTO mode, the green LED will be on .

2006 VOLVO XC90


OperationPress to operate the Air Quality sensor (normal setting).

Or:Select one of the following three functions by pressing 1, 2 or 3 times.1. The AUT LED lights. The Air Quality sensor is now activated.2. No LED lights. Recirculation is not activated unless needed to cool the passenger compartment in a warm climate.3. The MAN LED lights. Recirculation is now activated.

Keep in mind the following:

Make it a rule to have the Air Quality sensor activated at all times.Recirculation is limited in cold climates to avoid fogging.If window fogging occurs, you should deactivate the Air Quality sensor.If fogging occurs, use the defroster functions for the windshield, side windows and rear window. See page 54.The filter should be changed at the intervals recommended in the maintenance schedule. However, if the vehicle is

used in a severely contaminated environment, it may be necessary to change the filter more frequently.


2006 VOLVO XC90

https://www.customers.volvocars.com/owners/docs/2006/2006_XC90/06xc90_02b.htm[8/9/2009 5:28:10 PM]


Tailgate wiper/washer

Tailgate wiper/washer

A - Intermittent wiping

B - Normal wiping

Move the lever forward to start the tailgate washer.

Tailgate wiper and reverse gearIf the front wipers are on and the car is put into reverse gear, then the tailgate wiper will go into intermittent wipingfunction*.If the tailgate wiper is already in normal wiping function, the normal wiping function will continue.

* Consult your Volvo retailer if you would like to have this function deactivated.


Hazard warning flashers, rear window/sideview mirror defroster, heatedfront seats

Hazard warning flashersThe four-way flasher should be used to indicate that the vehicle has become a traffic hazard. To activate the flashers,press the triangular button in the center dash. Press the button again to turn off the flashers.

NOTE: Regulations regarding the use of the hazard warning flasher may vary, depending on where you live.

2006 VOLVO XC90


Sideview mirror and rear window defrosterPress the switch to start heating the rear window and sideview mirrors to remove ice or condensation. An LED in theswitch will light up.

A timer automatically switches off the heating to the sideview mirrors after approximately 4 minutes and to the rearwindow after approximately 12 minutes. The LED will go out correspondingly.

Heated front seats (option)

The front seat heating can be switched on and off as required.Press the switch once for maximum seat heating. Both LED's in the switch will be lit.Press the switch a second time for comfort heating. One LED in the switch will be lit.Press the switch a third time to turn the heating off completely.

The seat heating for the passenger seat should be switched off when the seat is not occupied.


Trip computer (option)

The trip computer stores information gathered from several systems in your vehicle and has four menus that can bedisplayed in the text window.

Driving distance on current fuel reserveAverage fuel consumptionCurrent fuel consumptionAverage speedCurrent speed in mph (Canadian models only)

NOTE: Warning messages from the vehicle's monitoring systems will override the trip computer function. If a

2006 VOLVO XC90


warning message is displayed in the text window while you are using the trip computer, you must acknowledge themessage by pressing button A. Press button A again to return to the trip computer function.

Trip computer controls and functions.

The four* trip computer functions can be accessed by twisting control B one step at a time in either direction. Twistinga fifth** time returns you to the original function.

The trip computer can be reset (current data will be erased from system memory) by pressing RESET (button C).

1. Driving distance on current fuel reserveThis function shows the approximate distance that can be driven on the fuel remaining in the tank. This calculation isbased on average fuel consumption during the last 12 miles (20 km) of driving and the amount of fuel remaining in thetank when the reading was taken.

When the driving distance on current fuel reserve is less than 12 miles (20 km), "----" will be displayed in the textwindow.

2. Average fuel consumptionThis value indicates fuel consumption since the last time the trip computer was reset (by pressing RESET, button C).When the engine is switched off, information on fuel consumption is stored and remains in system memory until theRESET (button C) is pressed again.

3. Current fuel consumptionThis value indicates the current fuel consumption, based on readings taken once per second. When the vehicle is notmoving, "----" will be displayed.

4. Average speedThis value indicates average speed since the last time the trip computer was reset (by pressing RESET, button C).When the engine is switched off, information on average speed is stored and remains in system memory until theRESET (button C) is pressed again.

5. Current speed in miles per hour (Canadian models only)This function provides the driver with an instantaneous conversion of the vehicle's current speed from km/h to mph.NOTE: Trip computer readings may vary slightly depending on the circumference of the tires on the vehicle.

* Five functions on Canadian models ** A sixth time on Canadian models


Cruise control

2006 VOLVO XC90


Cruise controlThe cruise control panel is located on the left side of the steering wheel hub.

Engaging cruise controlPress the CRUISE button. CRUISE will be displayed in the information window in the instrument panel.

NOTE: This does not set the vehicle's speed.

Setting speedPress + or - to set the current speed. CRUISE ON will be displayed in the information window in the instrument panel.

Increasing or decreasing speedUse + or - in the following ways to increase or decrease the vehicle's speed:

Press and hold down + or - until the vehicle reaches the desired speed. Press + or - for approximately a half second and release the button to increase or decrease vehicle speed by

approximately 1 mph (1.6 km/h).

NOTE: Cruise control will not function at speeds below approximately 20 mph (30 km/h).

Braking

Cruise control is automatically disengaged when the brake pedal is depressed. The currently set speed is stored inmemory.

Pressing resume will return the vehicle to the previously set speed.

AccelerationMomentary acceleration, such as when passing another vehicle, does not affect cruise control operation. The vehiclewill automatically return to the previously set speed when you release the accelerator pedal.

Disengaging cruise controlTo disengage cruise control, press the CRUISE button. CRUISE or CRUISE-ON will no longer be displayed in theinformation window in the instrument panel.

NOTE: Cruise control is automatically disengaged if:

the engine is switched off the gear selector is placed in (N)eutral the wheels start to spin or lock if an increase in speed is maintained for more than one minute if the vehicle's speed falls below approximately 20 mph (30 km/h).

Temporarily disengaging cruise control

2006 VOLVO XC90


Press 0 to temporarily disengage cruise control. CRUISE will be displayed in the information window in theinstrument panel.

Press the brake pedal.


Press "resume" to return to the previously set speed.

WARNING!The Cruise control should not be used in heavy traffic or when driving on wet or slippery roads, or when driving onunpaved or uneven road surfaces. Cruise control may not maintain set speed on steep downgrades.


Opening the tailgate, Auxiliary 12-volt sockets

Opening the tailgateTo open the upper section of the tailgate, pull the handle (A) downward.

To fold down the lower section of the tailgate, pull handle (B) upward.

12-volt socket at the rear of the center console (option)

Auxiliary 12-volt socketsThese 12 volt sockets can be used to plug in certain accessories such as cellular telephones, etc.

12-volt socket in the cargo compartmentFold down the lid to use the socket.

NOTE!

2006 VOLVO XC90


If the 12-volt sockets are used while the engine is not running, there is a risk that the vehicle's battery will bedischarged.

12-volt socket in the cargo compartmentIf the ignition is switched off and a device drawing more than 0.1A is connected to a socket, a battery warning will

be displayed in the text window.The covers should be kept on when the auxiliary sockets are not in use.Maximum current from the sockets is 15A.

Ashtrays/cigarette lighterThe auxiliary sockets can also be used for cigarette lighters.Ashtrays and lighters are available as accessories. Please contact your Volvo retailer.


Parking brake, Opening/closing the hood

Parking brake

To apply the parking brake, press the pedal (C). The brake is applied to the rear wheels. The indicator light in theinstrument panel will light up to indicate that the parking brake is applied.

NOTE: There is also an audible signal that will sound if the car is driven with the parking brake engaged.

Release the parking brake pulling out the lower edge of the release handle (A).If you inadvertently pull the plastic cover (B), it can be pressed back into place.

2006 VOLVO XC90


Opening the hood

WARNING! Always use the parking brake when parking. On hills, also turn the front wheels toward the curb.The indicator lightin the instrument panel will light up even if the parking brake is applied only slightly. Be sure to press down on thepedal sufficiently.

Opening/closing the hood1. Pull the lever (1) located under the left side of the dashboard to release the hood lock.2. Lift the hood slightly.3. Press up the release control (2) located under the front edge of the hood and lift.

To close the hood, place your hand on it and press down until the hood locks in the closed position.

WARNING!

Do not grasp the ribs in the grille when closing the hood. If your fingers protrude through the grille, they could beinjured on components in the engine compartment as the grille closes. We recommend pressing down on the hood toclose it.

Check that the hood locks properly when closed!


Electrically operated windows

The electrically operated windows are controlled by buttons in the arm rests.The ignition switch must be ON* (ignition key in position I, II or the engine running) for the electrically operated

windows to function.To lower: Press down the front edge of the button to the first detent ("stop").To raise: Lightly pull up the front edge of the button to the first detent ("stop").

* The electrically operated windows will also function after the ignition has been switched off as long as neither of thefront doors has been opened.

Auto up/down function (front doors only):Either front door window can be opened or closed automatically.

Auto down: Press the front part of the button as far down as possible and release it immediately. To stop the windowat any time, pull the button up.

Auto up: Pull the front part of the button up as far as possible and release it immediately. To stop the window at any

2006 VOLVO XC90


time, press the button down.

A - front windows, B - rear windows

NOTE: If a window is obstructed during auto-up, it will automatically reverse direction and return to its startingposition. If a window is repeatedly obstructed during auto-up operation, an overload protection circuit breaker willtemporarily halt window function. The window will return to normal function after a brief cool-down period.

WARNING!

Always remove the ignition key when the vehicle is unattended.Make sure that childrens' hands are clear before raising the windows.Never leave children unattended in the vehicle.


Lockout switch for rear windows

Lockout switch for rear windowsThe electrically operated rear door windows can be disabled by a switch located on the driver's door (see illustration).

If the light in the switch is OFF: The rear door windows can be raised or lowered with the buttons on the rear doorarmrests or with the buttons on the driver's door armrest.

If the light in the switch is ON: The rear door windows can only be raised or lowered with the buttons on the driver'sdoor armrest.

2006 VOLVO XC90


Electrically operated window in the front passenger's seatThe control for the electrically operated window in the front passenger's seat operates that window only.

Electrically operated windows in the rear doors.The rear door windows can be operated with the control on each door and the switch on the driver's door. If the lightin the switch for blocking electrically operated windows in the rear doors (located in the driver's door control panel) ison, the rear door windows can only be operated from the driver's door.


Rearview mirror/power folding sideview mirrors

Rearview mirrorA Normal position

B Night position, reduces glare from following headlights

Autodim function (option)The autodim function reacts to headlights from following traffic and automatically reduces glare.

2006 VOLVO XC90


NOTE: The autodim function is automatically switched off when the gear selector is placed in the Reverse position.

Electrically operated sideview mirrorsThe mirror control switches are located on the driver's door armrest.

Driver's side: Press the L button (a light in the switch will go on) to activate the adjustment control. Use this controlto adjust the driver's door mirror.

Passenger's side: Press the R switch (a light in the switch will go on) to activate the adjustment control. Use thiscontrol to adjust the passenger's door mirror.

CAUTION:Use the mirror heating function (see page 54) to remove ice or snow from the mirrors. An ice scraper could damagethe surface of the mirror.

After you have adjusted the mirror(s), press the L or R switch again (the LED will go out) to deactivate the adjustmentcontrol.

WARNING!The mirrors should always be adjusted prior to driving. Objects seen in the passenger's side wide-angle sideviewmirror are closer than they appear to be.

Mirror memory function (with the central locking system) - optionIf you lock the vehicle and later unlock it with the same remote control and open the driver's door, the sideviewmirrors (and the driver's seat) will automatically move to the position they were in when you left the vehicle. Thisfeature will work in the same way with all of the remote control transmitters (up to 3) that you use with your vehicle.This feature will not function if you lock your vehicle with the key.


Water repellent glass-option The sideview mirrors and side door windows can be treated with a water repellent coating. The optional laminated sidewindows always have this coating.

The coating improves vision by causing the water to run off quickly. See page 137 for information on cleaning thistype of glass.

CAUTION

2006 VOLVO XC90


Use only suitable plastic scrapers to remove ice or snow from the mirrors. Using a metal ice scraper could damagethe water repellent coating.

Use the heating function to remove ice, snow, or mist from the mirrors


Power moonroof (option)

Power moonroofTo operate the moonroof, turn the ignition key to position I or II, or start the engine. The moonroof can be operated intwo ways:

A. Tilt positionB. Sliding moonroof

A. Tilt position Open: With the moonroof closed, push up the rear edge of the switch (position 5 in the illustration below).

Close: Pull down and hold the rear edge of the switch (position 6 in the illustration below) until the moonroof hasclosed completely.

B. Sliding moonroofManual open: Pull the switch rearward to position 3 and hold it until the moonroof has opened to the position of yourchoice.Auto open: Pull the switch as far back as possible (position 4) and release it to automatically slide open the moonroofto the "comfort"* position. Pull the switch rearward again to open the moonroof completely.

Manual close: Push the switch to position 2 and hold it until the moonroof has closed completely or to the position ofyour choice.Auto close: Push the switch forward as far as possible (position 1) and release it to automatically close the moonroof.

2006 VOLVO XC90


CAUTION

Remove ice and snow before opening the moonroof.Do not operate the moonroof if it is frozen closed.Never place heavy objects on the moonroof.

WARNING!

Never open/close the moonroof if it is obstructed in any way when in operation.Never allow a child to operate the moonroof.Never extend any object or body part though the open moonroof, even if the vehicle's ignition is completely

switched off.Never leave a child alone in a vehicle.

* A position where the moonroof is not quite fully open, which helps alleviate "rumbling" wind noise.


If the moonroof is obstructed during auto-close operation, it will automatically reverse direction and return to itsstarting position. If the moonroof is repeatedly obstructed during auto-close operation, an overload circuit breaker willtemporarily halt moonroof function. The moonroof will return to normal function after a brief cool-down period.

VisorThe optional moonroof also features a sliding visor. The visor slides open automatically when the moonroof is opened,and must be closed manually.



2006 VOLVO XC90


pg. 67 Interior

Storage compartments

pg. 68 Interior

Storage compartments (contd)

Storage compartment in the center consoleTo open the lid on the storage compartment, press the lower edge of the opening latch (see illustration above). This lidcan be folded back to form a small table area for rear seat passengers.

2006 VOLVO XC90


Lift the tray under the lid to expose the deep storage bin with slots for CD storage.

Cup holders for the front seatsTwo cup holders are provided for the front seat occupants. Press lightly on the rear edge of the cover to open it.

Ashtray (accessory)An ashtray insert is available from your Volvo retailer. This insert slides into either of the cup holders.

Pen holderThere is a pen holder in the center console, in front of the gear selector.

pg. 69 Interior

Storage compartment in rear side of center consoleGrasp the upper edge of cover and pull to open this compartment.

Ashtray (accessory)An ashtray insert is available from your Volvo retailer.

2006 VOLVO XC90


Cup holders for the rear seats

Grasp the lower edge of the panel to pull out the cup holders in the rear side of the center console.The cup holder insert can be removed to provide space for a large plastic bottle. Pull the insert straight up to remove

it. Press down to reinsert it.

Glove compartmentThe glove compartment can be used to store things such as the owner's manual, maps, pens, etc.

pg. 70 Interior

Storage compartments (contd)

Coat hangerUse the coat hanger for light jackets, etc.`

Storage space between rear seats (seven-seat models) - optionThis storage space provides compartments for pens or other small items.

2006 VOLVO XC90


Rear side storage compartments and cup holders (seven-seat models)Lift the lid to access the storage compartment.

pg. 71 Interior

Securing cargo

Securing cargoAs a safety precaution, all cargo in your vehicle should be securely anchored to keep it from being thrown forward inthe event of sudden braking, etc. The vehicle is equipped with eyelets in the cargo space to which straps or other cargorestraints can be attached.

WARNING!The eyelets are not to be used as passenger restraints or as anchorages for child restraints.

Consult your Volvo retailer about suitable accessories for this purpose.

Remember that an object weighing 44 lbs (20 kg) produces a force of 2,200 lbs (1,000 kg) in a head-on collisionat 30 mph (50 km/h)!Keep the following in mind when loading the vehicle:

The load carrying capacity of your vehicle is determined by factors such as the number of passengers, the amount ofcargo, the weight of any accessories that may be installed, etc. See the section "Vehicle loading" in the chapter "Wheeland tires" for more detailed information.

Load the cargo against the backrest.Load heavy cargo as low as possible.If no one is sitting in the outboard rear seat(s), reinforce the backrest by fastening the seat belts.Never load cargo above the backrest without a cargo net.

2006 VOLVO XC90


WARNING!When the rear backrest(s) are folded down, the vehicle should not be loaded to a level higher than 2 in. (5 cm)below the upper edge of the rear side windows. Objects placed higher than this level could impede the function ofthe Inflatable Curtain.

pg. 72 Interior

Nylon cargo net (option)The Volvo XC90 can be equipped with a cargo net made of strong nylon fabric.

This net can be installed in two places:

Behind the rear seat backrests (the second row of seats in seven-seat models)Behind the front seat backrests if the rear seat backrests (the second row of seats in seven-seat models) have been

folded down.

If the vehicle is equipped with the cargo area cover, lift the cover out of the vehicle before installing the cargo net.

1. The upper and lower rods of the cargo net are hinged. Position the rods so that they are straight and lock in position.

2. Insert the end of the upper rod in one of the attachment brackets (see illustration above).3. Insert the other end of the rod in the attachment bracket on the opposite side of the vehicle.4. Attach the lower straps to the eyelets on the floor if the net has been installed in the rear attachment brackets.Use the eyelets in the front seat rails if the net has been installed in the forward attachment brackets.

NOTE: On seven-seat models: When using the net in the rear attachment brackets, be sure it is installed in front of theside armrests.5. Adjust the straps to pull the net taut.

2006 VOLVO XC90


Folding and storing the cargo netPress the release buttons on the hinges (1 in the illustration above) and fold the net.The cargo net can be stored under the floor of the cargo area on five-seat models.

WARNING!Be sure the cargo net is properly inserted in the attachment brackets and the straps are correctly attached to theeyelets and pulled taut.Do not use the net if it is damaged in any way.When it is not in use, store the net so that it cannot be thrown forward in the event of sudden braking, etc.

pg. 73 Interior

Steel grid (accessory)To install the grid:Upper attachments1. Lift in the grid through the tailgate or through one of the rear passenger doors (in this case, fold down the rear seatbackrests/backrests in second row of seats in seven-seat models).2. Insert one of the grid's upper attachments into an attachment bracket above one of the rear passenger doors (seeillustration above).3. Push the grid's attachment into the forward position in the attachment bracket (see inset illustration above) to lockthe attachment in place.4. Insert the grid's other upper attachment in the attachment bracket above the opposite rear passenger door, and pressthe attachment into the forward position in the attachment bracket to lock it in place.

2006 VOLVO XC90


Lower attachments1. Insert the lower attachment bracket through the steel grid's lower mount from underneath.2. Install the spring on the attachment bracket and tighten the knob.3. Secure the attachment bracket hook in the lower cargo eyelet. Turn the knob to tension the attachment bracket in thecargo eyelet.4. Repeat the operation on the opposite side.5. Tighten both attachment brackets alternatively.6. Place the protective caps on the threads above the knobs.

WARNING!Seven-seat models:- The backrests of the optional third row seats must be folded down when installing the steel grid.- The steel grid is installed behind the second row of seats in seven-seat models. To avoid the risk of injury, no oneshould be allowed to sit in the third row of seats when the steel grid is in place in the vehicle.

pg. 74 Interior

Securing cargo (contd)

Cargo area cover (option)Installing the cargo area cover:Press the end pieces of the cargo area cover down in the holders.

Pull out the cargo area cover and hook it in the holes in the rear cargo area pillars (see illustration above).

Removing the cargo area cover:Press the end pieces of the cover inward. Pull up and lift out.

2006 VOLVO XC90


Grocery bag holder 1. Fold down the lower section of the tailgate.2. Fold up the rear section of the cargo compartment floor.3. Hang or secure your grocery bags by means of the straps or holders.


2006 VOLVO XC90


2 0 0 6 VOLVO

XC90

Audio

pg. 183 Audio

Audio system 184

Audio system controls 185

Audio functions 188

Radio functions 192

Menu settings and selections 198

CD player 199

CD changer (option) 201

Audio systems - general information 203

HomeLink® Universal Transceiver 204

pg. 184 Audio

Audio system

1. On/Off2. Volume3. CD player

2006 VOLVO XC90


4. AM/FM - for switching between FM1, FM2 and AM5. Display6. ENTER - select in the menu or activate a selection7. MY KEY - programmable key for your favorite function from the menu8. SELECTOR - select sound source9. SOUND - make sound settings10. EXIT/CLEAR - step back in the menu or cancel a selection11. Menu selections12. CD eject13. CD slot, CD changer (option)14. Storage compartment15. MY KEY - programmable keys for your favorite functions from the menu16. Station preset buttons/CD changer discs (1-6)17. Infrared (IR) port - for the optional audio/navigation system remote control18. Seek/change tracks or stations

pg. 185 Audio

Audio system controls

Steering wheel keypad (option)The four buttons on the steering wheel keypad can be used to control the audio system. The steering wheel keypad canbe used to adjust volume, shift between preset stations and change CD tracks.

Press the or buttons briefly to search for a radio station, or to go to the next/previous track on a CD

Press and hold down these buttons to search within a track.

2006 VOLVO XC90


DisplayThe display (1) shows the currently selected function, menu selections, etc.Clean the display with a dry, soft, lint-free cloth. Do not use cleaning agents.

Accessing and using menusIn menu mode, you can change settings and program new functions in the audio system. The various menu alternativesare shown in the display.

Press the menu button (2) to enter menu mode. Use the menus as follows:

Use the menu keys (3) to navigate up or down in the menus. Dots in the display indicated that there are more menuselections from which to choose.

One long press on EXIT/CLEAR exits menu mode. A short press on the EXIT/CLEAR enables you to cancel, undo, or answer no to a menu selection, or to go back in

the menu structure. Pressing ENTER confirms a menu selection, or takes you to the next submenu.

pg. 186 Audio

Audio system controls (contd)

Rear headphone connectors and controls (option)The door panels behind the second row of seats can be equipped with headphone connectors for passengers in thesecond and optional third row of seats. Several people can listen to different sound sources, such as CDs or the radio atthe same time without disturbing each other.

Two sets of headphones can be plugged into each connector.

Use the SEL button (1) to step between the sound sources. Press the arrow keys (2) briefly to change CD tracks or switch between preset stations. Hold down the arrow keys to fast forward/reverse, or search for the previous/next strong radio station. Hold down the SEL button to turn off the sound.

For the best sound reproduction, we recommend headphones with impedance between 16-32 ohm. The sensitivity ofthese should be equal to or greater than 102 dB. The headphone connections are intended for 3.5 mm contacts and arelocated under the lower edge of the socket.

All headphones are automatically turned off when the ignition is switched off. They must be manually restarted whenthe ignition is switched on again.

2006 VOLVO XC90


Headphones - limitations

The headphones will only work when the ignition key is in position I or higher. If a set of headphones is connected to the same source that is being sent through the speakers, the headphone

controls cannot be used to change track or station. This is to prevent the driver from being distracted by an unexpectedchange in music.

If the driver selects the same sound source as someone listening to this source through headphones, the driver takescontrol of the sound source.

Only one disc in the optional CD changer, and one track on the CD can be played at a time. Headphone users can choose from among the preset radio stations (AM, FM1, FM2) previously set by the driver. If FM is played in the speakers, AM is not available and vice versa.

pg. 187 Audio

Remote control (option)1. Memory - stores radio stations that have been found by a search

To store a station:- Press the memory button (1). The preset station number will flash 4 times in the display- While the preset number is flashing, use the + or - buttons (5) to select a position at which to store the station- Press button 1 again to store the station

2. Volume3. Forward/back - fast forward or back4. Source - step between sound sources5. Preset/disc - selects among CD's (in the optional CD changer) or preset radio stations6. Auto store - searches for and stores the strongest radio stations7. Not in use8. Not in use9. Power - off/on

Point the remote control toward the IR port on the radio panel (see the illustration on page 184).

NOTE: If the remote control does not function properly, check the batteries (AAA or R03).

pg. 188 Audio

Audio functions

2006 VOLVO XC90


On/Off buttonTo activate the system:1. Turn the ignition key to position I.2. Press the POWER button (1) to switch the audio system on or off.

NOTE: If you switch off the ignition while the audio system is on, the system will be on when the ignition is switchedon again.

Volume controlTurn the knob (2) clockwise or counterclockwise to raise or lower the volume. The volume control is electronic andhas no end position. Volume can also be raised (+) or lowered (-) using the optional steering wheel keypad.

Pause modeIf the volume is turned off, the CD player will go into pause mode. Re-activate the player by turning up the volume.

Selecting a sound sourceA sound source can be selected either with the function buttons (3) - CD, AM/FM, or with the SELECTOR control(4).

To select a sound source:

Turn the SELECTOR control to choose FM1, FM2, AM, CD, CD changer (option) Press the AM/FM button repeatedly to choose between FM1, FM2, AM Press the CD button to change to the CD player or optional CD changer

The selected sound source will be shown in the display.

pg. 189 Audio

2006 VOLVO XC90


Sound settings1. Press the SOUND button (1) repeatedly until you come to the setting that you wish to change. Choose BASS,TREBLE, FADER, BALANCE, SUBWOOFER (option), CENTER (option) or SURROUND (option).2. Use the SELECTOR control (2) to adjust the level of the setting you have selected. The display shows a scale frommin. to max. position. The center indicates the normal position.

NOTE: - Sound level for the center speaker can only be set if Dolby Pro Logic II (DPL II) or three-channel stereo (3-CH) isselected in the menu. - Sound level for the subwoofer can only be set if SUBWOOFER is selected in the menu.- Volume for the surround sound can only be set if Dolby Pro Logic II (DPL II) is selected in the menu.

Setting Shown in the displayBass BASSTreble TREBLEBalance between the right and left speakers BALANCEBalance between the front and rear speakers FADERBass speaker level SUBWOOFER (option)Center speaker level CENTER (Premium Sound system only)Surround sound level SURROUND (Premium Sound system only)

pg. 190 Audio

Audio function (contd)

2006 VOLVO XC90


SURROUND MODEDolby Surround Pro Logic II (DPL II), 3-channel stereo (3-CH) - optionDolby Surround Pro Logic II together with a center speaker in the dashboard offers you a sound experience very closeto a live performance. The normal left-right stereo channels are divided to left-center-right. In addition, surroundsound is produced by the rear speakers. This surround sound mirrors the resonance of a concert hall. Dolby SurroundPro Logic II functions in CD and FM modes. 3-channel stereo is recommended for AM radio broadcasts.

Surround settings for FM and CD are stored separately.When listening to FM radio stations, Dolby Surround Pro Logic II functions best in areas with strong reception. If

reception is weak, selecting 2 or 3- channel stereo may provide better sound quality.Dolby Surround Pro Logic II is only available on the highest level audio system - Premium Sound.

Use the following instructions to select PRO LOGIC II, 3-CHANNEL, or to turn these functions off. See also themenu structure on page 198.1. Select AUDIO SETTINGS in the menu and press ENTER.2. Select SURROUND and press ENTER.3. Select Dolby AM/FM, or Dolby CD and press ENTER.4. Select PRO LOGIC II, 3-CHANNEL, or OFF and press ENTER.

The symbol PL II is displayed when Pro Logic II is selected.3-CH is shown when 3-channel stereo is selected.OFF indicates normal stereo mode.

Dolby noise reduction is manufactured under license from Dolby Laboratories Licensing Corporation.

"Dolby Surround Pro Logic II", and the double-D symbol are trademarks of Dolby Laboratories LicensingCorporation. Dolby Surround Pro Logic II is manufactured under licence from Dolby Laboratories LicensingCorporation.

pg. 191 Audio

2006 VOLVO XC90


Bass speaker - SUBWOOFER (option)The subwoofer helps the system provide fuller sound and deeper bass.1. Select AUDIO SETTINGS in the menu and press ENTER.2. Select SUBWOOFER and press ENTER. See page 189 for information on setting the subwoofer level.

Equalizer FREQ - FRONT(certain audio systems)This function is used to fine-tune the sound from the front speakers.1. Select AUDIO SETTINGS in the menu and press ENTER.2. Select Equalizer FR and press ENTER.3. Use the menu selection buttons to set the level or use the SELECTOR control.4. Press ENTER to select the next frequency. You can select five frequencies.5. Press ENTER until you come to the menu mode to save the changes you have made.

Equalizer RREQ - REAR (certain audio systems)This function is used to fine-tune the sound from the rear speakers.1. Select AUDIO SETTINGS in the menu and press ENTER.2. Select EQ- REAR and press ENTER.3. Use the menu selection buttons to set the level or use the SELECTOR control.4. Press ENTER to select the next frequency. You can select five frequencies.5. Press ENTER until you come to the menu mode to save the changes you have made.

pg. 192 Audio

Radio functions

2006 VOLVO XC90


Station search

1. Choose radio mode AM/FM1/FM2 using the SELECTOR control (1) or the AM/FM button (2).2. Press briefly on or to search for the next strong station. The radio will search for the next audible station

and then stop.

3. Press one of the buttons again to start a new search.

Manually search for a known frequency

1. Press and hold the or button (or the corresponding buttons on the steering wheel keypad). MAN will be

shown in the display. The radio will slowly scroll in the desired direction and then increase speed after a few seconds.2. Release the button when the desired frequency is displayed.3. If you need to adjust the frequency, press briefly on or .

4. The manual search function is available for five seconds after you last pressed the button.

pg. 193 Audio

Storing stationsTo store a selected station under one of the station setting buttons 0-9 (1):

2006 VOLVO XC90


1. Set the desired station.2. Press the button under which the station is to be stored and keep it depressed. The sound will be interrupted forseveral seconds and STATION STORED is shown in the display. The station is now stored.

You can store up to 10 stations each for AM, FM1 and FM2, i.e. a total of 30 stations.

Radio Frequency bandFM 87.7 - 107.9 MHzAM 530 - 1710 kHz

MY KEY - programming a shortcutUse the MY KEY buttons (2, 3) to program a favorite function from the menu, such as SCAN, AUTOSTORE, etc.See page 198 for the functions that can be programmed with the MY KEY button.

1. Use the MENU buttons to scroll among the functions.2. Select the desired function from the menu by holding one of the MY KEY buttons depressed for more than twoseconds.3. When MY KEY STORED is shown in the display, the function has been stored.4. Activate the function by briefly pressing the MY KEY button with which the functions was stored.

Repeat steps 1-4 to store new functions on the MY KEY buttons.

NOTE: The MY KEY buttons can only be programmed for one shortcut function at a time.

pg. 194 Audio

Radio functions (contd)

Automatically storing stations - AUTOSTOREThis function automatically searches for, and stores up to 10 strong AM or FM stations in a separate memory. If morethan 10 stations are found, the 10 strongest ones will be stored. The function is especially useful in areas in which youare not acquainted with radio stations or their frequencies.

1. Choose radio mode using the SELECTOR control or the AM/FM button.2. Select AUTOSTORE in the menu and press ENTER.3. Select AST SEARCH and press ENTER.4. AUTOSTORING is shown in the display and a number of strong stations (max. 10) from the set frequency band arenow automatically stored in the autostore memory. If there are no stations with sufficient signal strength, NO AST

2006 VOLVO XC90


FOUND is displayed.5. The stored stations are available under the buttons 0-9 (1).6. When the radio is in autostore mode, AUTO is shown in the display. AUTO disappears when you return to thenormal radio mode.7. Return to normal radio mode by pressing the AM/FM button or EXIT/CLEAR.8. To access previously stored stations, carry out steps 1-2 but select AST MODE in step 3 and press ENTER.

pg. 195 Audio

Radio Broadcast Data System (RBDS)This feature, which may not be available in your area, functions only with FM broadcasts.

The radio in your car is equipped with an advanced system allowing information from broadcasters to be transmittedvisually, as text, together with the audio signal. This information is then decoded by the radio and made available forseveral new and unique features. The RBDS or Radio Broadcast Data System operates in the FM band only,and the information transmitted is supplied exclusively by participating broadcasters. Volvo has no control overthe accuracy of the data or information.

Coverage by local broadcasters may be limited at this time, but as the technology and benefits grow, you will find theradio in your car is equipped to take advantage of this system.

NOTE: PI (Program Information) Seek: When an FM station has been stored as a preset, the radio also stores RBDSprogram information if it is available. When the preset is selected at a later time, the radio tries to access updatedprogram information. In weak signal areas, there may be a delay before the station becomes audible. During this delay,there will be no sound and the text "PI seek. Press EXIT to cancel." will be displayed. You may press EXIT toimmediately tune in the station without RBDS program information.

Scanning - SCANThis function automatically searches for the next strongest AM and FM stations. When the radio finds a station, it willpause for approximately 8 seconds, after which it will continue scanning.1. Choose radio mode using the SELECTOR control (1) or the AM/FM button (2).2. Select SCAN to start searching and press ENTER.3. SCAN will be shown in the display.4. Press the EXIT/CLEAR button to stop scanning.

pg. 196 Audio

2006 VOLVO XC90


Radio functions (contd)

Program type/Format - PTYThe PTY function allows you to find programs that suit your taste. Use the PTY function to select from among thedifferent program types shown in the list.

Which PTY does the set station have?

1. Select RADIO SETTINGS in the menu and press ENTER.2. Select PTY in the menu and press ENTER.3. Select SHOW PTY TEXT and press ENTER. The PTY of the selected station is now shown in the display.

NOTE: Not all radio stations have PTY designations.

Program type Text displayedSwitch off/deactivate CLEAR ALL PTYNews NEWSInformation INFORMATIONSports SPORTTalk TALKRock ROCKClassic rock CLASSIC ROCKAdult hits ADULT HITSSoft rock SOFT ROCKTop 40 TOP 40Country COUNTRYOldies OLDIESSoft SOFTNostalgia NOSTALGIAJazz JAZZClassical CLASSICALRhythm & Blues RHYTHM & BLUESSoft R&B SOFT R&BLanguage LANGUAGEReligious music RELIGIOUS MUSICReligious talk RELIGION TALK

2006 VOLVO XC90


Personality PERSONALITYPublic PUBLICCollege COLLEGEWeather WEATHER

Radio textCertain stations broadcast program information, which can be shown in the display.

1. Press the MENU button.2. Select RADIOTEXT in the menu and press ENTER.3. Select RADIOTEXT again to deactivate.

pg. 197 Audio

Search for a specific program type - PTYThis functions enables you to search for a certain type of program by searching through the entire waveband.

1. Select FM1 or FM2 and press the MENU button.2. Select RADIO SETTINGS and press ENTER.3. Select PTY and press ENTER.4. Choose SELECT PTY and press ENTER.5. Press ENTER for one or more of the listed program types to select. The PTY symbol is displayed and lights upwhen you make your first selection and the radio goes into PTY mode.6. When you have made all of your selections, press EXIT/CLEAR to exit the PTY list.7. Select SEARCH PTY and press ENTER. If the radio finds a station with the selected program type, this station willbe played.8. If the radio finds a station that does not match your selections, continue the search with the and buttons.

9. If no station with the selected program type is found, the radio will return to the previously tuned frequency. PTYwill remain in standby mode.10. To deactivate the PTY standby mode, select CLEAR ALL PTY and press ENTER. The PTY symbol thendisappears and the radio returns to the normal operating mode.

PTY standbyTo set the radio in PTY standby, repeat steps 1-6.

2006 VOLVO XC90



2006 VOLVO XC90


2 0 0 6 VOLVO

XC90

Interior

pg. 57 Interior

Front seats 58

Rear seats 62

Interior lighting 65

Floor mats 66

Storage compartments 67

Securing cargo 71

pg. 58 Interior

Front seats

Manually adjusted front seats

2006 VOLVO XC90


1. Front-rear adjustment: lift the bar and move the seat to the position of your choice.2. Raise/lower the front edge of the seat cushion (option): use the control to pump the front edge of the cushion up ordown.3. Raise/lower seat height: pump the seat up or down.4. Lumbar support: turn the control for firmer or softer lumbar support.5. Backrest tilt: turn the control to adjust the angle of the backrest.6. Control panel for optional power seat (see page 60 for more information).

WARNING!- Do not adjust the seat while driving. The seat should be adjusted so that the brake pedal can be depressed fully. Inaddition, position the seat as far rearward as comfort and control allow.- Check that the seat is securely locked into position after adjusting.

pg. 59 Interior

Folding the backrests in the front seatThe front passenger seat backrest can be folded to a horizontal position to make room for a long load. Fold thebackrest as follows:

Move the seat as far back as possible.Adjust the backrest to the upright position.Lift the catches on the rear of the backrest.Without releasing the catches, push the backrest forward.Move the seat as far forward as possible so that the head restraint slides under the glove compartment.

WARNING!Cover sharp edges on the load to help prevent injury to occupants. Secure the load to help prevent shifting duringsudden stops.

pg. 60 Interior

Front seats (contd)

Power seatOperation

Driver's seat: The seat can be adjusted if the ignition key is in position I, II or if the engine is running. It can also be adjusted as follows with the ignition off:

2006 VOLVO XC90


Within approximately 4 minutes after the driver's door has been unlocked from the outside and has been opened andremains open.

Within 40 seconds, if the driver's door has just been closed. Within 40 seconds, if the driver's door has not been opened after the ignition has been switched off.

Passenger seat: The seat can only be adjusted if the ignition key is in position I, II or if the engine is running.

Seat adjustmentAdjust the power seat(s) with the two controls at the side of the seat as follows:1 - Front edge of seat (raise/lower)2 - Forward - rearward3 - Rear edge of seat (raise/lower)4 - Backrest tilt

Power seat adjustment controlsThe power seats have an overload protector that activates if a seat is blocked by any object. If this occurs, switch offthe ignition (key in position 0) and wait about 20 seconds before operating the seat again.

Emergency stopIf the seat accidentally begins to move, press any of the buttons to stop the seat.

NOTE: Please refer to the following page for information on programming the memory function in the driver's seat.

Power seat adjustment controls

Remote keyless entry system and driver's seatThe remote control transmitter also controls the electrically operated driver's seat in the following way:

Adjust the seat to your preferences.When you leave your vehicle, lock it using the remote control.

The position of the seat is now stored in the remote control.

Automatic seat adjustmentTo move the seat to the position in which you left it:1. Unlock the driver's door with the same remote control (the one used to lock the doors)2. Open the driver's door within 2 minutes. The driver's seat will automatically move to the position in which you leftit.

NOTE:

The seat will move to this position even if someone else has moved it to a different seating position and locked thecar with a different remote control.

This feature will work in the same way with all of the remote control transmitters (up to 3) that you use with yourvehicle.

This feature will not function if your lock your vehicle with the key.

pg. 61 Interior

2006 VOLVO XC90


WARNING!- Because the driver's seat can be adjusted with the ignition off, children should never be left unattended in thevehicle.- Movement of the seat can be STOPPED at any time by pressing any button on the power seat control panel.- Do not adjust the seat while driving.- The seat should be adjusted so that the brake pedal can be depressed fully. In addition, position the seat as farrearward as comfort and control allow.- The seat rails on the floor must not be obstructed in any way when the seat is in motion.

Programming the memoryThree different seating and door mirror positions can be stored in the driver seat's memory.The following example explains how button 1 can be programmed.Buttons 2 and 3 can be programmed in the same way.To program (store) a seat position in button 1:1. Move the seat to the desired position using the seat adjustment controls (see the previous page).2. Press and hold down the MEM (memory) button.3. With the MEM button depressed, press button 1 briefly to store the seat's current position.

To move the seat to the position that it was in when button 1 was programmed:Press and hold down button 1 until the seat stops moving.

As a safety precaution, the seat will stop automatically if the button is released before the seat has reached the presetposition.

pg. 62 Interior

Rear seats

Entering the optional third row of seatsTilting the outboard backrests in the second row of the seats: Pull up the handle (1), hold it up, and tilt the backrest forward to move the seat.Return the backrest to the upright position to slide the seat back to its original position.

2006 VOLVO XC90


Forward/rearward seat adjustmentLift the adjustment bar (2) to move the seat forward or rearward.

Removing the center console (seven-seat models only)In order to make it possible to move the center seat in the second row of seats as far forward as possible (seven-seatmodels only), the rear section of the center console can be removed.

Pull the handle (see illustration above) and lift out the console.To return the console to its original position, slide it back into position until it clicks into place.

Sliding center seat - second row (seven-seat models only)The center seat in the second row can be moved farther forward than the outboard seats. This makes it possible for achild seated in this position to sit closer to the people in the front seats.

pg. 63 Interior

Head restraint - second row, center positionThe head restraint in the center position can be adjusted to 4 different heights.

To raise - pull the restraint up until it clicks into one of the four heights positions.

2006 VOLVO XC90


To lower - press the button at the base of the support (see illustration above) and press the head restraint down.

WARNING!- Please note that the lowest head restraint position is only intended for use when the backrest is to be folded down,or when the seat is not occupied.- The head restraint is intended to help protect the head/neck in a collision. Ensure that it is properly adjusted for theoccupant of the seat.

pg. 64 Interior

Rear seats (contd)

Folding the backrests - second row of seats1. Move the seat(s) to their rearmost position (seven-seat models only).2. Pull the loop (A) to fold down an outboard head restraint. Press down the center head restraint if necessary (seepage 63).3. Pull the handle (B) outward to release the backrest. The backrests are designed to lock at a 45 degree angle. Pull thehandle again to continue pressing it down until it locks in the horizontal position.To return the backrests to the upright position, pull handle B and pull the backrest up.

Folding the backrests - third row of seats (option)Folding down the backrestIf necessary, fold in the load anchorage eyelets before folding down the backrests.1. Move the seats in the second row forward, see page 62.2. Pull up the handle in illustration 1 above.3. Push the seat cushion firmly rearward, under the backrest.4. Fold down the backrests* (the head restraints fold down automatically) to the horizontal position.

Returning the backrest to the upright position

2006 VOLVO XC90


Fold up the backrest to the upright position.Grasp the strap (see illustration 3 above) and pull the seat cushion out until it locks in place. This also locks the

backrest in the upright position.

* Please note that the head restraints in this row cannot be vertically adjusted.

pg. 65 Interior

Interior lighting

Courtesy light/front reading lightsThe courtesy/reading lights can be turned on or off by pressing the respective buttons.

The courtesy light has a timer function which turns the light1 on for 30 seconds if:

You unlock the vehicle from the outside with the key or remote control.You switch off the ignition (turn the key to position 0).

The courtesy light stays on for 10 minutes if one of the doors is left open after the vehicle is unlocked.

The courtesy light switches off if:

The engine is started.The vehicle is locked from the outside with the key or remote control.

The courtesy light can be switched off or on in all situations by briefly pressing the button.

When you switch the light on, it remains lit for 10 minutes.

You can disconnect the automatic function by pressing the courtesy light button for more than 3 seconds. Brieflypressing the courtesy light button again automatically reconnects the function.

The courtesy light timer periods can be changed. Contact your Volvo retailer.

2006 VOLVO XC90


Rear reading lights

The reading lights can be switched on or off by pressing the respective buttons.Seven-seat models: Both reading lights for the third row of seats will switch on if one of the buttons is pressed.The reading lights switch off automatically after 10 minutes if the engine is not running.The lights can be switched off at any time by pressing the button.

1. In dark conditions

pg. 66 Interior

Vanity mirror

The light comes on when you open the cover.

Floor Mats

Volvo offers floor mats specially manufactured for your vehicle. They must be properly placed and secured in the matclips.

WARNING!An extra mat on the driver's floor can cause the accelerator pedal to catch. Check that the movement of theaccelerator pedal is not impeded. No more than one protective floor covering may be used at one time.

2006 VOLVO XC90



2006 VOLVO XC90


2 0 0 6 VOLVO

XC90

Locks and Alarms

pg. 75 Locks and Alarms

Keys and remote controls 76

Locking and unlocking 79

Child safety locks 81

Alarm 82


Keys and remote controls

KeysTwo types of keys are provided with your vehicle; master keys and a service (valet) key. The master key, the remotecontrol, and the central locking button may all be used to lock and unlock all of your vehicle's locks.

The service key will operate only the driver's door and the ignition switch. It is intended to help deter unwanted entry

2006 VOLVO XC90


into the glove compartment.

To use your keys:

Turn the key once to unlock the driver's door only.Turn the key again (within 10 seconds) to unlock all doors and the tailgate.One turn with the key towards lock in the drivers door locks all doors, tailgate.Use the switch on the driver's door armrest to lock/unlock the vehicle from the inside.

WARNING!If the doors are locked while driving, this may hinder rapid access to the occupants of the vehicle in the event of anaccident. (Also see information on "Child safety locks").

NOTE: To help prevent accidentally locking the keys in the vehicle, the central locking system is designed to unlockthe doors immediately if the key is left in the ignition switch, the vehicle is locked using the lock button on the doorand the door is then closed. A sound from the lock will be audible at this time.

Please note that this function will not unlock the doors if the engine is running.

Immobilizer (start inhibitor)Each of the keys supplied with your vehicle contains a coded transmitter. The code in the key is transmitted to anantenna in the ignition switch where it is compared to the code stored in the start inhibitor module. The vehicle willstart only with a properly coded key.

Each key has a unique code, which your Volvo retailer uses if new keys are required. A maximum of six remotecontrols/keys can be programmed and used for one car.

If you misplace a key, take the other keys to an authorized Volvo retailer for reprogramming as an antitheft measure.

If two of the keys to your vehicle are close together, e.g., on the same key ring, when you try to start the vehicle, thiscould cause interference in the immobilizer system and result in the vehicle not starting. If this should occur, removeone of the keys from the key ring before trying to start the vehicle again.

NOTE: This device complies with part 15 of the FCC rules. Operation is subject to the following condition: (1) Thisdevice may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation.


Remote controlsYour vehicle is equipped with two coded remote control transmitters with integrated ignition keys called Key

2006 VOLVO XC90


Integrated Remote (KIR). These transmitters use a radio frequency that will enable you to lock/unlock all doors and thetailgate from a distance of 10-15 feet (3-5 meters).

The transmitters will also activate or allow "keyless" entry into the passenger compartment or the tailgate. They willalso activate or deactivate the vehicle's alarm system(s). The car can also be locked/unlocked with the key.

If one of the transmitters is misplaced, contact your nearest authorized Volvo retailer for replacement.

Buttons in remote control:1 -Fold key in/out, 2 - Lock, 3 - Approach lighting, 4 - "Panic" function, 5 - Unlock tailgate, 6 - Unlock

Using the remote controlButton 1: Press to extend the key. This button must also be pressed when the key is folded back into the slot in theside of the remote control unit.Button 2 (Lock): Press once to lock all doors, and the tailgate.Button 3 (Approach lighting): Press this button when approaching the car at night to light up the interior courtesylight, parking lights, license plate lights and the lights in the sideview mirrors.Button 4 (Panic): See page 82 for more information on this function.Button 5 (Tailgate unlock): Press this button twice within 3 seconds to unlock the tailgate (without unlocking theother doors).Button 6 (Unlock): Press this button once to unlock the driver's door only. Wait for at least 1 second and press thebutton again (within 10 seconds) to unlock all doors, and the tailgate.

NOTE:

If an airbag deploys, your vehicle's SRS control module will attempt to automatically unlock all doors.The keys may also be used to lock and unlock the doors, and to activate and deactivate the alarm system.To avoid leaving your keys in the vehicle, make a habit of always locking the vehicle with the remote control.

Automatic re-locking If the doors are unlocked, the locks will automatically reengage (re-lock) and the alarm willrearm after 2 minutes unless a door or the tailgate has been opened.

Automatic locking (option)The doors lock automatically when the vehicle's speed exceeds approximately 5 mph (7 km/h) and remain locked adoor is opened from the inside or until the car is unlocked with the remote.


FCC ID:LQNP2T-APU This device complies with part 15 of the FCC rules. Operation is subject to the followingconditions: (1) This device may not cause harmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation.

Canadian 2306104388 Model 504 2927 by Donnelly Operation is subject to the following conditions: (1) this devicemay not cause interference, and (2) this device must accept any interference, including interference that may cause

2006 VOLVO XC90


undesired operation of the device.Canadian 2306104388A Model 509 977 by Connaught Electronics Operation is subject to the following conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference thatmay cause undesired operation of the device.

WARNING!Never use the transmitter to lock the doors from inside the vehicle.

Doing so would ACTIVATE:- the break-in alarm, which would sound if one of the doors were opened- the optional interior motion and inclination alarm sensors.

Doing so would DEACTIVATE:- the moonroof and interior courtesy light controls.- the central locking buttons on the front door armrests, although the interior door handles would still function toallow occupants to leave the vehicle.

Disabled features would remain disabled until the remote were used again to unlock the vehicle.In addition, locking an occupied vehicle would hinder rapid access to the occupants in an accident or emergency.

Replacing the battery in the remote controlIf the range of the transmitter is noticeably reduced, this indicates that the battery is weak and should be replaced.

To replace the battery1. Carefully pry open the rear edge of the cover with a small screwdriver.2. Insert a new 3-volt, CR2032 battery, with the battery's plus side up. Avoid touching the contact surfaces of thebattery with your fingers.3. Press the cover back into place. Ensure that the rubber seal is correctly positioned to help keep out moisture.

NOTE: The old battery should be disposed of properly at a recycling center or at your Volvo retailer.


Locking and unlocking

2006 VOLVO XC90


Locking and unlocking the vehicle from the insideThe switch on the driver's door armrest can be used to lock or unlock all doors and the tailgate, and to set the alarm.

Locking the glove compartmentThe glove compartment can be locked with the master key.


Locking and unlocking (contd)

Unlocking the tailgateThe tailgate lock is incorporated in the central locking system and is locked or unlocked when all doors arelocked/unlocked.

The tailgate can be unlocked by:

Pressing UNLOCK on the remote control twice.Using the central locking button on the driver's door.

2006 VOLVO XC90


Pressing twice on the remote control's tailgate unlock button (see illustration above). Relock the tailgate using the remote's "Lock" button.

Automatic relocking:

If you use the tailgate unlock button to unlock the tailgate without opening it, it will automatically relock afterapproximately 2 minutes.

Note: If you open the tailgate and close it again, it will remain unlocked and the alarm will not be rearmed. Press thelock button on the remote control to relock the tailgate and rearm the alarm.


Child safety locks in the rear doors

Child safety locks

Manual child safety locks - rear doors/tailgateThe controls are located on the rear door jambs and at the lower edge of the tailgate. Use a key or small screwdriver toadjust these controls.

A The door/tailgate cannot be opened from the inside. The door/tailgate can be opened from the outside. B The door/tailgate locks function normally.

Child safety lock in the tailgate

WARNING!Remember, in the event of an accident, the rear seat passengers cannot open the doors from the inside with thebuttons in position A.

2006 VOLVO XC90


Power child locks (option) To prevent the rear doors from being opened from the inside:

1. Turn the vehicle's ignition key to at least position 1.

2. Press the button shown above.

Indicator light in the button ON: the doors cannot be opened from the inside. Normal operation from the outside.

Indicator light in the button OFF: the doors can be opened from the inside.


Alarm

AlarmThe alarm is automatically armed whenever you lock your vehicle.

When armed, the alarm continuously monitors a number of points on the vehicle. The following conditions will set offthe alarm:

The hood is forced open.The tailgate is forced open.A door is forced open.The ignition switch is tampered with.If there is movement in the passenger compartment (if the vehicle is equipped with the optional movement sensor).The vehicle is lifted or towed (if the vehicle is equipped with the optional inclination sensor).The battery is disconnected (while the alarm is armed).The siren is disconnected when the alarm is disarmed.

Arming the alarmPress the LOCK button on the remote control, lock the vehicle using the key in the driver's door or press the centrallock button on driver's doors with the door open. One long flash of the turn signals will confirm that the alarm isarmed.

Disarming the alarmPress the UNLOCK button on the remote control or unlock the doors with the key.

Turning off (stopping) the alarmIf the alarm is sounding, it can be stopped by pressing the UNLOCK button on the remote control or by unlocking the

2006 VOLVO XC90


driver's door with the key.

Audible/visual alarm signalAn audible alarm signal is given by a battery powered siren. The alarm cycle lasts for 25 seconds.

The visual alarm signal is given by flashing all turn signals and turning on the interior lighting for approximately 5minutes.

"Panic" buttonIn an emergency situation, this feature can be used to attract attention.

Activate the "panic" button by pressing the red button on the remote control (see illustration on page 77) for at least 3seconds or by pressing this button twice within 3 seconds. The turn signals will flash, and the vehicle's horn willsound.

The function can be turned off by pressing any of the buttons on the remote control or will stop automatically after 25seconds. When a button is pressed, there is a 5 second delay before the panic alarm is deactivated.

NOTE: This button will NOT unlock the vehicle.


Temporarily turning off the inclination and movement alarm sensor(s) - accessoryThis button will only be found in vehicles equipped with the accessory inclination and/or movement sensors.

FCC ID: MAYDA5823This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1) This devicemay not cause harmful interference, and (2) this device must accept any interference received, including interferencethat may cause undesired operation.

Canadian IC: 4405A-DA5823Movement sensor DA5823 by DynexOperation is subject to the following conditions: (1) this device may not cause interference, and (2) this device mustaccept any interference, including interference that may cause undesired operation of the device.

In certain situations it may be desirable to turn off the accessory inclination and movement alarm sensors if, forexample, you drive your vehicle onto a ferry where the rocking of the boat could trigger the alarm or if a pet is left inthe vehicle with the doors locked.

To temporarily turn off the inclination and movement alarm sensors from the alarm system:

2006 VOLVO XC90


From the time the ignition key is turned from the Drive position (position II) until you lock the vehicle, you can pressthe button in the center console. The LED in the switch will light up and a message will be displayed in the textwindow to indicate that the sensors are disconnected.

The vehicle can then be locked in the usual way to set the alarm.

NOTE:

This function will not turn off the vehicle's standard alarm.The optional sensors are automatically reconnected to the alarm system the next time the vehicle is unlocked and

then locked again.

LED alarm status signalsThe status of the alarm system is indicated by the red LED at the top of the dash:

LED off - the alarm is not armedLED flashes once per second - the alarm is armedLED flashes rapidly before the ignition is switched on - the alarm has been triggeredFault in the alarm system: If a fault has been detected in the alarm system, a message will be displayed in the text

window. Contact your Volvo retailer.

Automatic re-lock/re-arm systemIf the vehicle is unlocked with the remote, the vehicle will re-lock and the alarm will re-arm after 2 minutes unless adoor or the tailgate has been opened.


This page intentionally left blank


2006 VOLVO XC90


2 0 0 6 VOLVO

XC90

Safety

pg. 1 Safety

Occupant safety, Reporting safety defects 2

Seat belts 3

Supplemental Restraint System (SRS) 5

Front airbags 6

Occupant Weight Sensor (OWS) 9

Side impact (SIPS) airbag 12

Volvo Inflatable Curtain (VIC) 13

Inspecting SRS Ssystem components 14

Whiplash Protection System (WHIPS) 15

Child safety 17

pg. 2 Safety

Occupant safety, Reporting safety defects

Volvo Concern for SafetySafety is the Volvo cornerstone. Our concern dates back to 1927 when the first Volvo rolled off the production line.Three-point seat belts (a Volvo invention), safety cages, and energy-absorbing impact zones were designed into Volvocars long before it was fashionable or required by government regulation. We will not compromise our commitment tosafety. We continue to seek out new safety features and to refine those already in our cars. You can help. We wouldappreciate hearing your suggestions about improving automobile safety. We also want to know if you ever have asafety concern with your car. Call us in the U.S. at: 800-458-1552 or in Canada at: 800-663-8255.

Occupant safetyHow safely you drive doesn't depend on how old you are, but rather on:

How well you see.Your ability to concentrate.How quickly you make decisions under stress to avoid an accident.

The tips listed below are suggestions to help you cope with the ever changing traffic environment.

Never drink and drive.

2006 VOLVO XC90


If you are taking any medication, consult your physician about its potential effects on your driving abilities.Take a driver-retraining course.Have your eyes checked regularly.Keep your windshield and headlights clean.Replace wiper blades when they start to leave streaks.Take into account the traffic, road, and weather conditions, particularly with regard to stopping distance.

Reporting Safety Defects in the U.S.If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you shouldimmediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Volvo Carsof North America. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safetydefect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot becomeinvolved in individual problems between you, your retailer, or Volvo Cars of North America. To contact NHTSA, youmay either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 202-366-0123 in Washington, D.C. area) orwrite to: NHTSA, U.S. Department of Transportation, Washington D.C. 20590. You can also obtain other informationabout motor vehicle safety from the Hotline.

Volvo strongly recommends that if your vehicle is covered under a service campaign, safety or emission recall orsimilar action, it should be completed as soon as possible. Please check with your local retailer or Volvo Cars of NorthAmerica, LLC if your vehicle is covered under these conditions.

NHTSA can be reached at:Internet:http://www.nhtsa.dot.govTelephone:1-888-DASH-2-DOT (1-888-327-4236) (toll free)1-800-424-9393 (toll free)1-202-366-0123 (in Washington DC area)

pg. 3 Safety

Seat belts

Adjusting the seat belt

Using seat belts Volvo, the inventor of the three-point seat belt, urges you and all occupants of your vehicle to wear seat belts andensure that children are properly restrained, using an infant, car, or booster seat determined by age, weight and height.

Volvo also believes no child should sit in the front seat of a vehicle.

Most states and provinces make it mandatory for occupants of a vehicle to use seat belts.

http://www.nhtsa.dot.gov/

2006 VOLVO XC90


Seat belt tensioners The seat belts are equipped with tensioners that reduce slack in the belts. These tensioners are triggered in situationswhere the airbags deploy. The front seat belts also include a tension reducing device which, in the event of a collision,limits the peak forces exerted by the seat belt on the occupant.

Buckling a seat belt Pull the belt out far enough to insert the latch plate into the receptacle until a distinct click is heard. The seat beltretractor is normally "unlocked" and you can move freely, provided that the shoulder belt is not pulled out too far.

The retractor will lock up as follows:

if the belt is pulled out rapidlyduring braking and accelerationif the vehicle is leaning excessivelywhen driving in turns

When wearing the seat belt remember:

The belt should not be twisted or turned.The lap section of the belt must be positioned low on the hips (not pressing against the abdomen).Make sure that the shoulder belt is rolled up into its retractor and that the shoulder and lap belts are taut.

Unbuckling the seat belt To remove the seat belt, press the red section on the seat belt receptacle. Before exiting the vehicle, check that the seatbelt retracts fully after being unbuckled. If necessary, guide the belt back into the retractor slot.

Sample label found on all seat belts with tensioners

Seat belt reminder The seat belt reminder consists of an audible signal, an indicator light above the rearview mirror, and a symbol in theinstrument panel that alert the driver and front seat passenger if their seat belts are not fastened.

Seat belt maintenance Check periodically that the seat belts are in good condition. Use water and a mild detergent for cleaning. Check seatbelt mechanism function as follows: attach the seat belt and pull rapidly on the strap.

pg. 4 Safety

WARNING!

Never use a seat belt for more than one occupant.

2006 VOLVO XC90


Never wear the shoulder portion of the belt under the arm, behind the back or otherwise out of position. Such usecould cause injury in the event of an accident.

Seat belts lose much of their strength when exposed to violent stretching and should be replaced after anycollision, even if they appear to be undamaged.

Never repair the belt yourself; have this work done by an authorized Volvo service technician only.Any device used to induce slack into the shoulder belt portion of the three-point belt system will have a

detrimental effect on the amount of protection available to you in the event of a collision.The seat back should not be tilted too far back. The shoulder belt must be taut in order to function properly.Do not use child safety seats or child booster cushions/backrests in the front passenger's seat. We also recommend

that children who have outgrown these devices sit in the rear seat with the seat belt properly fastened.

Seat belt use during pregnancy

Seat belt use during pregnancyThe seat belt should always be worn during pregnancy. But it is crucial that it be worn in the correct way. The diagonalsection should wrap over the shoulder then be routed between the breasts and to the side of the belly. The lap sectionshould lay flat over the thighs and as low as possible under the belly. It must never be allowed to ride upward. Removeall slack from the belt and insure that it fits close to the body without any twists.

As a pregnancy progresses, pregnant drivers should adjust their seats and steering wheel such that they can easilymaintain control of the vehicle as they drive (which means they must be able to easily operate the foot pedals andsteering wheel). Within this context, they should strive to position the seat with as large a distance as possible betweentheir belly and the steering wheel.

Child seats Please refer to page 19 for information on securing child seats with the seat belts.

pg. 5 Safety

Supplemental Restraint System (SRS)

SRS warning light

Supplemental Restraint System

2006 VOLVO XC90


As an enhancement to the three-point seat belts, your Volvo is equipped with a Supplemental Restraint System (SRS).Volvo's SRS consists of seat belt tensioners, front airbags, side impact airbags, the occupant weight sensor, andinflatable curtains. All of these systems are monitored by the SRS control module. An SRS warning light in theinstrument panel (see the illustration above) illuminates when the ignition key is turned to position I, II, or III, and willnormally go out after approximately 7 seconds if no faults are detected in the system.

Where applicable, a text message will also be displayed when the SRS warning light illuminates. If this warningsymbol is not functioning properly, the general warning symbol illuminates and a text message will be displayed.

WARNING!

If the SRS warning light stays on after the engine has started or if it illuminates while you are driving, have thevehicle inspected by a trained and qualified Volvo service technician as soon as possible.

Never try to repair any component or part of the SRS yourself. Any interference in the system could causemalfunction and serious injury. All work on these systems should be performed by an authorized Volvo servicetechnician.

WARNING!If your vehicle has been subjected to flood conditions (e.g. soaked carpeting/standing water on the floor of thevehicle) or if your vehicle has become flood-damaged in any way, do not attempt to start the vehicle or put the keyin the ignition before disconnecting the battery (see below). This may cause airbag deployment which could result inpersonal injury. Have the vehicle towed to a trained and qualified Volvo service technician for repairs.

Automatic transmission: Before attempting to tow the vehicle, use the following procedure to override the shiftlock system to move the gearselector to the neutral position:

Switch off the ignition for at least 10 minutes and disconnect the batteryWait at least one minute.Insert the key in the ignition and turn it to position II.Press firmly on the brake pedal.Move the gear selector from (P)ark to the (N)eutral position.

pg. 6 Safety

Front airbags

The front airbag system The front airbags supplement the three-point seat belts. For these airbags to provide the protection intended, seat beltsmust be worn at all times.

2006 VOLVO XC90


The front airbag system includes gas generators (1) surrounded by the airbags (2) and a deceleration sensor (3) thatactivates the gas generators, causing the airbags to be inflated with nitrogen gas.

As the movement of the seats' occupants compresses the airbags, some of the gas is expelled at a controlled rate toprovide better cushioning. Both seat belt tensioners also deploy, minimizing seat belt slack. The entire process,including inflation and deflation of the airbags, takes approximately one fifth of a second.

Passenger side airbag - above glove compartment

The location of the front airbags is indicated by "SRS AIRBAG" embossed on the steering wheel pad and above theglove compartment, and by decals on both sun visors and on the front and far right side of the dash.

The driver's side front airbag is folded and located in the steering wheel hub.The passenger's side front airbag is folded behind a panel located above the glove compartment.

WARNING!

The airbags in the vehicle are designed to be a SUPPLEMENT to-not a replacement for-the three-point seat belts.For maximum protection, wear seat belts at all times. Be aware that no system can prevent all possible injuries thatmay occur in an accident.

Never drive a vehicle with a steering wheel-mounted airbag with your hands on the steering wheel pad/airbaghousing.

The front airbags are designed to help prevent serious injury. Deployment occurs very quickly and withconsiderable force. During normal deployment and depending on variables such as seating position, one mayexperience abrasions, bruises, swellings, or other injuries as a result from deployment of one or both of the airbags.

When installing any accessory equipment, make sure that the front airbag system is not damaged. Any interferencein the system could cause malfunction.

pg. 7 Safety

Front airbags

Front airbag deployment

The front airbags are designed to deploy during certain frontal or front-angular collisions, impacts, or decelerations,depending on the crash severity, angle, speed and object impacted. The airbags may also deploy in certain non-frontalcollisions where rapid deceleration occurs.

The SRS sensors, which trigger the front airbags, are designed to react to both the impact of the collision and theinertial forces generated by it, and to determine if the intensity of the collision is sufficient for the seat belt tensionersand/or airbags to be deployed.

However, not all frontal collisions activate the front airbags.

If the collision involves a nonrigid object (e.g., a snow drift or bush), or a rigid, fixed object at a low speed, thefront airbags will not necessarily deploy.

2006 VOLVO XC90


Front airbags do not normally deploy in a side impact collision, in a collision from the rear or in a rollover situation.The amount of damage to the bodywork does not reliably indicate if the airbags should have deployed or not.

NOTE:

Deployment of front airbags occurs only one time during an accident. In a collision where deployment occurs, theairbags and seat belt tensioners activate. Some noise occurs and a small amount of powder is released. The release ofthe powder may appear as smoke-like matter. This is a normal characteristic and does not indicate fire.

Volvo's dual-threshold, dual-stage front airbags use special sensors to control deployment. The point at which theairbag deploys is determined by whether or not the seat belt is being used, as well as the severity of the collision.

Collisions can occur where only one of the airbags deploys. If the impact is less severe, but severe enough to presenta clear injury risk, the dual-stage airbags are triggered at 70-80% of their total capacity. If the impact is more severe,the dual-stage airbags are triggered at full capacity.

Should you have questions about any component in the SRS system, please contact a trained and qualified Volvoservice technician or Volvo Customer Support:

In the USA: Volvo Cars of North America Customer Care Center P.O. Box 914 Rockleigh, New Jersey 07647-09141-800-458-1552 http://www.volvocars.usIn Canada: Volvo Cars of Canada Ltd.National Customer Service175 Gordon Baker RoadNorth York, Ontario M2H 2N71-800-663-8255 http://www.volvocanada.com

WARNING!

Do not use child safety seats or child booster cushions/backrests in the front passenger's seat. We also recommendthat occupants under 4 feet 7 inches (140 cm) in height who have outgrown these devices sit in the rear seat with theseat belt fasteneda.

Never drive with the airbags deployed. The fact that they hang out can impair the steering of your vehicle. Othersafety systems can also be damaged.

The smoke and dust formed when the airbags are deployed can cause skin and eye irritation in the event ofprolonged exposure.

a. See also the Occupant Weight Sensor information on page 9.

pg. 8 Safety

Front airbags (contd)


http://www.volvocanada.com/

2006 VOLVO XC90


WARNING!

Children must never be allowed in the front passenger's seat. Volvo recommends that ALL occupants (adults andchildren) shorter than 4 feet 7 inches (140 cm) be seated in the back seat of any vehicle with a passengerside frontairbag. See page 19 for guidelines.

Occupants in the front passenger's seat must never sit on the edge of the seat, sit leaning toward the instrumentpanel or otherwise sit out of position.

The occupant's back must be as upright as comfort allows and be against the seat back with the seat belt properlyfastened.

Feet must be on the floor, e.g., not on the dash, seat or out of the window.

WARNING!

No objects or accessory equipment, e.g. dashboard covers, may be placed on, attached to, or installed near the airbag hatch (the area above the glove compartment) or the area affected by airbag deployment (see the illustration onpage 6).

There should be no loose articles, e.g. coffee cups, on the floor, seat, or dashboard area.Never try to open the airbag cover on the steering wheel or the passenger's side dashboard. This should only be

done by a trained and qualified Volvo service technician.

Failure to follow these instructions can result in injury to the vehicle occupants.

pg. 9 Safety

Occupant Weight Sensor (OWS)

2006 VOLVO XC90


Disabling the passenger's side front airbag Volvo recommends that ALL occupants (adults and children) shorter than four feet seven inches (140 cm) be seated inthe back seat of any vehicle with a front passenger side airbag, and be properly restrained for their size and weight.See also the child safety recommendations on page 19.

The passenger's side front airbag is automatically enabled/disabled by the Occupant Weight Sensor (OWS), a systemthat monitors the weight of the person or object in the front passenger's seat. The system consists of a silicone-filledbag located under the padding in the front passenger's seat cushion, a control module located under this seat, and a seatbelt tension sensor, located on the outboard side of the seat.

The OWS system continuously monitors the pressure on the front passenger's seat cushion and the tension applied tothe seat belt. Based on this data, OWS assesses the weight of the occupant or object in the front passenger's seat. Thisinformation is transmitted to the SRS system control module, which enables or disables the passenger's side frontairbag accordingly, as indicated in the table below.

If the system is functioning normally, the status of the front passenger's side airbag (enabled/ disabled) will be shownby the OWS indicator light as explained in the table to the right. The OWS indicator light is separate and in addition tothe SRS warning light in the instrument panel.

NOTE: When the ignition is switched on, the OWS indicator light will go on for up to 10 seconds while the systemperforms a selfdiagnostic test and then go out. However, if a fault is detected in the system:

The OWS indicator light will stay onThe SRS warning light (see page 5) will come on and stay onThe message PASS. AIRBAG OFF SERVICE URGENT will be displayed in the information display.

2006 VOLVO XC90


(contd. on following page)

pg. 10 Safety

Occupant Weight Sensor (OWS)

WARNING!If a fault in the system is detected and indicated as explained on the previous page, be aware that the passenger'sside front airbag will not deploy in the event of a collision.

In this case, the safety systems and Occupant Weight Sensor should be inspected by an authorized Volvo retailer assoon as possible.

Modifications If you are considering modifying your vehicle in any way to accommodate a disability, for example by altering oradapting the driver's or front passenger's seat(s) and/or airbag systems, please contact Volvo at:

In the USA: Volvo Cars of North America Customer Care Center P.O. Box 914 Rockleigh, New Jersey 07647-0914

2006 VOLVO XC90


1-800-458-1552 In Canada: Volvo Cars of Canada Ltd.National Customer Service175 Gordon Baker RoadNorth York, Ontario M2H 2N71-800-663-8255

WARNING!

No objects that add to the total weight on the seat should be placed on the front passenger's seat. If a child is seatedin the front passenger's seat with any additional weight, this extra weight could cause the OWS system to enable theairbag, which might cause it to deploy in the event of a collision, thereby injuring the child.

The seat belt should never be wrapped around an object on the front passenger's seat. This could interfere with theOWS system's function.

The front passenger's seat belt should never be used in a way that exerts more pressure on the passenger thannormal. This could increase the pressure exerted on the weight sensor by a child, and could result in the airbag beingenabled, which might cause it to deploy in the event of a collision, thereby injuring the child.

WARNING!

Never try to open, remove, or repair any components in the OWS system. This could result in system malfunction.Maintenance or repairs should only be carried out by an authorized Volvo service technician.

The front passenger's seat should not be modified in any way. This could reduce pressure on the seat cushion,which might interfere with the OWS system's function.

pg. 11 Safety

Occupant Weight Sensor (OWS) (contd)

WARNING!Keep the following points in mind with respect to the OWS system. Failure to follow these instructions couldadversely affect the system's function and result in serious injury to the occupant of the front passenger's seat:

The full weight of the front seat passenger should always be on the seat cushion. The passenger should never lifthim/herself off the seat cushion using the armrest in the door or the center console, by pressing the feet on the floor,by sitting on the edge of the seat cushion, or by pressing against the backrest in a way that reduces pressure on theseat cushion. This could cause OWS to disable the front passenger's side airbag.

Do not place any type of object on the front passenger's seat in such a way that jamming, pressing, or squeezingoccurs between the object and the front seat, other than as a direct result of the correct use of the ALR/ ELR seatbelt (see page 19).

No objects should be placed under the front passenger's seat. This could interfere with the OWS system's function.

pg. 12 Safety

Side impact (SIPS) airbag

2006 VOLVO XC90


Location of the side impact (SIPS) airbag

Side impact airbags - front seats only As an enhancement to the structural side impact protection built into your car, the car is also equipped with SideImpact Protection System (SIPS) airbags.

The SIPS airbag system is designed to help increase occupant protection in the event of certain side impact collisions.The SIPS airbags are designed to deploy only during certain sideimpact collisions, depending on the crash severity,angle, speed and point of impact.

NOTE: SIPS airbag deployment (one airbag) occurs only on the side of the vehicle affected by the impact. The airbagsare not designed to deploy in all side impact situations.

Components in the SIPS airbag system This SIPS airbag system consists of a gas generator (2), the side airbag modules built into the outboard sides of bothfront seat backrests (3), and electronic sensors/wiring (1).

WARNING!

The SIPS airbag system is a supplement to the structural Side Impact Protection System and the three-point seatbelt system. It is not designed to deploy during collisions from the front or rear of the car or in rollover situations.

The use of seat covers on the front seats may impede SIPS airbag deployment.No objects, accessory equipment or stickers may be placed on, attached to or installed near the SIPS airbag system

or in the area affected by SIPS airbag deployment.Never try to open or repair any components of the SIPS airbag system. This should be done only by a trained and

qualified Volvo service technician.In order for the SIPS airbag to provide its best protection, both front seat occupants should sit in an upright

position with the seat belt properly fastened.Failure to follow these instructions can result in injury to the occupants of the vehicle in the event of an accident.

2006 VOLVO XC90



2006 VOLVO XC90


2 0 0 6 VOLVO

XC90

Wheels and tires

pg. 111 Wheels and tires

General information 112

Tire inflation pressure tables 116

Tire Pressure Monitoring System (TPMS) - option on certain U.S. models only 117

Tire designations 119

Glossary of tire terminology 120

Vehicle loading 121

Uniform Tire Quality Grading 122

Snow chains, snow tire, studded tires 123

Temporary Spare 124

Changing wheels 125

Tire sealing system (option on certain models) 130


General information

General informationYour vehicle is equipped with tires according to the vehicle's tire information placard on the Bpillar (the structuralmember at the side of the vehicle, at the rear of the driver's door opening), or on the inside of the fuel filler door onCanadian models.The tires have good road holding characteristics and offer good handling on dry and wet surfaces. It should be notedhowever that the tires have been developed to give these features on snow/ice-free surfaces.Certain models are equipped with "all-season" tires, which provide a somewhat higher degree of road holding onslippery surfaces than tires without the "all-season" rating. However, for optimum road holding on icy or snow-covered roads, we recommend suitable winter tires on all four wheels.When replacing tires, be sure that the new tires are the same size designation, type (radial) and preferably from thesame manufacturer, on all four wheels. Otherwise there is a risk of altering the car's roadholding and handlingcharacteristics.

Storing wheels and tires When storing complete wheels (tires mounted on rims), they should be suspended off the floor or placed on their sideson the floor.

2006 VOLVO XC90


Tires not mounted on rims should be stored on their sides or standing upright, but should not be suspended.

Tread wear indicator

CAUTIONTires should preferably be stored in a cool, dry, dark place, and should never be stored in close proximity tosolvents, gasoline, oils, etc.

Tread wear indicatorThe tires have wear indicator strips running across or parallel to the tread. The letters TWI are printed on the side ofthe tire. When approximately 1/16" (1.6 mm) is left on the tread, these strips become visible and indicate that the tireshould be replaced. Tires with less than 1/16" (1.6 mm) tread offer very poor traction.When replacing worn tires, it is recommended that the tire be identical in type (radial) and size as the one beingreplaced. Using a tire of the same make (manufacturer) will prevent alteration of the driving characteristics of thevehicle.

WARNING!- The wheel and tire sizes for your Volvo are specified to meet stringent stability and handling requirements.Unapproved wheel/ tire size combinations can negatively affect your vehicle's stability and handling. Approved tiresizes are shown in the Tire inflation pressure tables on page 116.- Any damage caused by installation of unapproved wheel/tire size combinations will not be covered by your newvehicle warranty. Volvo assumes no responsibility for death, injury, or expenses that may result from suchinstallations.


New tiresRemember that tires are perishable goods. As of 2000, the manufacturing week and year will be indicated with 4 digits(e.g. 1502 means that the tire illustrated was manufactured during week 15 of 2002).

Tire age Tires degrade over time, even when they are not being used, which can affect their reliability and roadholdingcharacteristics. Therefore, all tires older than 6 years (including the spare tire and winter tires) should be inspected by aqualified technician, regardless of appearance or mileage. Heat caused by hot climates or frequent high loadingconditions can accelerate the aging process.

2006 VOLVO XC90


A tire's age can be determined by the DOT stamp on the sidewall (see the illustration above).

A tire with e.g., visible cracks or discoloration should be replaced immediately.

Improving tire economy:

Maintain correct tire pressure. See the tire pressure table on page 116. Drive smoothly: avoid fast starts, hard braking and tire screeching. Tire wear increases with speed. Correct front wheel alignment is very important. Unbalanced wheels impair tire economy and driving comfort. Tires must maintain the same direction of rotation throughout their lifetime. When replacing tires, the tires with the most tread should be mounted on the rear wheels to reduce the chance of

oversteer during hard braking. Hitting curbs or potholes can damage the tires and/or wheels permanently.


Tire inflation placards on U.S. models

Tire inflationCheck tire inflation pressure regularly. A table listing the recommended inflation pressure for your vehicle can befound on page 116. Tire inflation pressure placards are also located on the driver's side B-pillar (the structural memberat the side of the vehicle, at the rear of the driver's door opening), or on the inside of the fuel filler door on Canadianmodels. These placards indicate the designation of the factory-mounted tires on your vehicle, as well as load limits andinflation pressure.

Tire inflation placard on Canadian models

NOTE: The placards shown indicate inflation pressure for the tires installed on the car at the factory only.

2006 VOLVO XC90


Use a tire gauge to check the tire inflation pressure, including the spare, at least once a month and before long trips.You are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate.

Use the recommended cold inflation pressure for optimum tire performance and wear. Under-inflation or over-inflation may cause uneven treadwear patterns.

WARNING!- Under-inflation is the most common cause of tire failure and may result in severe tire cracking, tread separation, or"blowout," with unexpected loss of vehicle control and increased risk of injury.- Under-inflated tires reduce the load carrying capacity of your vehicle.

When weather temperature changes occur, tire inflation pressures also change. A 10-degree temperature drop causes acorresponding drop of 1 psi (7 kPa) in inflation pressure. Check your tire pressures frequently and adjust them to theproper pressure, which can be found on the vehicle's tire information placard or certification label.

Checking tire pressureCold tiresInflation pressure should be checked when the tires are cold.

The tires are considered to be cold when they have the same temperature as the surrounding (ambient) air.

This temperature is normally reached after the car has been parked for at least 3 hours.


After driving a distance of approximately 1 mile (1.6 km), the tires are considered to be hot. If you have to drivefarther than this distance to pump your tire(s), check and record the tire pressure first and add the appropriate airpressure when you get to the pump.

If checking tire pressure when the tire is hot, never "bleed" or reduce air pressure. The tires are hot from driving and itis normal for pressures to increase above recommended cold pressures. A hot tire at or below recommended coldinflation pressure could be significantly under-inflated.

To check inflation pressure:1. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve.2. Add air to reach the recommended air pressure3. Replace the valve cap.4. Repeat this procedure for each tire, including the spare.5. Visually inspect the tires to make sure there are no nails or other objects embedded that could puncture the tire andcause an air leak.6. Check the sidewalls to make sure there are no gouges, cuts, bulges or other irregularities.

NOTE:

If you overfill the tire, release air by pushing on the metal stem in the center of the valve. Then recheck the pressurewith your tire gauge.

Some spare tires require higher inflation pressure than the other tires. Consult the tire inflation table on page 116 orsee the inflation pressure placard.


Tire inflation pressure tablesTire pressures recommended by Volvo for your vehicle. Refer to the tire inflation placard for information specific to

2006 VOLVO XC90


the tires installed on your vehicle at the factory.

Cold tire pressure for vehicle loads up to 1160 lbs (525 kg)aTire size Front, psi (kPa) Rear, psi (kPa)XC90225/70R16235/65R17235/60R18255/50R19

39 (270) 39 (270)

Temporary spare tireT155/85R18 61 (420) 61 (420)

a. These weights include the weight of all occupants of the car plus cargo.

Optional tire pressure. These inflation pressures may only be used when the vehicle is not fully loaded.

Optional cold tire pressure that may only be used for vehicle loads up to 495 lbs (225 kg).Tire size Front, psi (kPa) Rear, psi (kPa)XC90225/70R16235/65R17235/60R18255/50R19

32 (220) 32 (220)

Temporary spare tireT155/85R18 61 (420) 61 (420)

NOTE: The optional tire pressure shown in the table above may not be used on XC90s equipped with the TirePressure Monitoring System (option as available). Vehicles with this system must use the standard tire pressure listedin the table in the left column (39 psi/270 kPa).


Tire Pressure Monitoring System (TPMS) - option on certain U.S. models onlyThe tire pressure monitoring system uses sensors mounted in the tire valves to check inflation pressure levels. Whenthe vehicle is moving at a speed of 20 mph (30 km/h) or faster, these sensors transmit inflation pressure data to areceiver located in the vehicle.

USA - FCC ID: MRXTG315AM04This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1) This devicemay not cause harmful interference, and (2) this device must accept any interference received, including interferencethat may cause undesired operation.

WARNING!The TPMS system uses a radio frequency of 315 MHz. Accessory electrical equipment using the same frequencycould interfere with TPMS and should not be installed in the vehicle. Please consult your Volvo retailer, a qualifiedVolvo service technician, or the accessory equipment's supplier for further information.

When low inflation pressure is detected, TPMS will light up the tire pressure warning light ( ) (also referred to as atelltale) in the instrument panel, and will display a message in the text window. The wording of this message is

2006 VOLVO XC90


determined by the degree of inflation pressure loss.

NOTE: If a fault occurs in TPMS, the tire pressure warning light will flash for approximately 1 minute and TIREPRESS SYST SERVICE REQUIRED will be displayed.

Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressurerecommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle hastires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should consultthe appropriate section of this owner's manual to determine the proper tire inflation pressure.) When the low tirepressure telltale is illuminated, one or more of your tires is significantly underinflated. You should stop and check yourtires as soon as possible, and inflate them to the proper pressure. Driving on a significantly underinflated tire causesthe tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and mayaffect the vehicle's handling and stopping ability. Your vehicle has also been equipped with a TPMS malfunctiontelltale to indicate when the system is not operating properly. When the malfunction telltale is illuminated, the systemmay not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety ofreasons, including the installation of incompatible replacement tires on the vehicle. Always check the TPMSmalfunction telltale after replacing one or more tires on your vehicle to ensure that the replacement tires arecompatible with the TPMS.

NOTE: TPMS indicates low tire pressure but does not replace normal tire maintenance. For information on correct tirepressure, please refer to the table on page 116, or consult your Volvo retailer.

Erasing warning messagesWhen a low tire pressure warning message has been displayed, and the tire pressure warning light has come on:1. Use a tire pressure gauge to check the inflation pressure of all four tires.2. Re-inflate the tire(s) to the correct pressure (consult the tire pressure placard or the table on page 116).3. Drive the car for at least one minute at a speed of 20 mph (30 km/h) or faster.

This will erase the warning text and the warning light will go out.



Changing tiresPlease note the following when changing or replacing the factory installed TPMS wheels/tires on the vehicle:

Only the factory-mounted wheels are equipped with TPMS sensors in the valves.If the vehicle is equipped with a temporary spare tire, this tire does not have a TPMS sensor.If winter wheels without TPMS sensors are mounted on the vehicle, TIRE PRESS SYST SERVICE REQUIRED will

be displayed each time the vehicle is driven above 25 mph (40 km/h) for 10 minutes or more.Once TPMS sensors are properly installed, the warning message should not reappear.Volvo recommends that TPMS sensors be fitted on all wheels used on the vehicle. Volvo does not recommend

moving sensors back and forth between sets of wheels.

CAUTIONWhen inflating tires with TPMS valves, press the pump's mouthpiece straight onto the valve to help avoid bending orotherwise damaging the valve.

WARNING!Incorrect inflation pressure could lead to tire failure, resulting in a loss of control of the vehicle.

2006 VOLVO XC90



Federal law mandates that tire manufacturers place standardized information on the sidewall of all tires (see theillustration).

The following information is listed on the tire sidewall:

The tire designation (the following figures are examples of a tire designation):

1. 215: the width of the tire (in millimeters) from sidewall edge to sidewall edge. The larger the number, the wider thetire.

2. 65: The ratio of the tire's height to its width.

3. R: Radial tire.

4. 15: The diameter of the wheel rim (in inches).

5. 95: The tire's load index. In this example, a load index of 95 equals a maximum load of 1521 lbs (690 kg).

6. H: The tire's speed rating, or the maximum speed at which the tire is designed to be driven for extended periods oftime, carrying a permissible load for the vehicle, and with correct inflation pressure. For example, H indicates a speedrating of 130 mph (210 km/h).

NOTE: This information may not appear on the tire because it is not required by law.

7. M+S or M/S = Mud and Snow, AT = All Terrain, AS = All Season

8. U.S. DOT Tire Identification Number (TIN): This begins with the letters "DOT" and indicates that the tire meets allfederal standards. The next two numbers or letters are the plant code where it was manufactured, the next two are thetire size code and the last four numbers represent the week and year the tire was built. For example, the numbers 317mean the 31st week of 1997. After 2000 the numbers go to four digits. For example, 2501 means the 25th week of2001. The numbers in between are marketing codes used at the manufacturer's discretion. This information helps a tiremanufacturer identify a tire for safety recall purposes.

9. Tire Ply Composition and Material Used: Indicates the number of plies indicates or the number of layers of rubber-coated fabric in the tire tread and sidewall. Tire manufacturers also must indicate the ply materials in the tire and thesidewall, which include steel, nylon, polyester, and others.

10. Maximum Load: Indicates the maximum load in pounds and kilograms that can be carried by the tire. Refer to thevehicle's tire information placard or the safety certification label, located on the B-Pillar or the driver's door or on theinside of the fuel filler door on Canadian models, for the correct tire pressure for your vehicle.

2006 VOLVO XC90


11. Treadwear, Traction, and Temperature grades: See page 122 for more information.

12. Maximum permissible inflation pressure: the greatest amount of air pressure that should ever be put in the tire. Thislimit is set by the tire manufacturer.


Glossary of tire terminologyThe tire suppliers may have additional markings, notes or warnings such as standard load, radial tubeless, etc.

Glossary of tire terminology

Tire information placard: A placard showing the OE (Original Equipment) tire sizes, recommended inflationpressure, and the maximum weight the vehicle can carry.

Tire Identification Number (TIN): A number on the sidewall of each tire providing information about the tirebrand and manufacturing plant, tire size and date of manufacturer.

Inflation pressure: A measure of the amount of air in a tire.Standard load: A class of P-metric or Metric tires designed to carry a maximum load at 35 psi [37 psi (2.5 bar) for

Metric tires]. Increasing the inflation pressure beyond this pressure will not increase the tires load carrying capability.Extra load: A class of P-metric or Metric tires designed to carry a heavier maximum load at 41 psi [43 psi (2.9 bar)

for Metric tires]. Increasing the inflation pressure beyond this pressure will not increase the tires load carryingcapability.

kPa: Kilopascal, a metric unit of air pressure.PSI: Pounds per square inch, a standard unit of air pressure.B-pillar: The structural member at the side of the vehicle behind the front door.Bead area of the tire: Area of the tire next to the rim.Sidewall of the tire: Area between the bead area and the tread.Tread area of the tire: Area of the perimeter of the tire that contacts the road when mounted on the vehicle.Rim: The metal support (wheel) for a tire or a tire and tube assembly upon which the tire beads are seated.Maximum load rating: a figure indicating the maximum load in pounds and kilograms that can be carried by the

tire. This rating is established by the tire manufacturer.Maximum permissible inflation pressure: the greatest amount of air pressure that should ever be put in the tire.

This limit is set by the tire manufacturer.Recommended tire inflation pressure: inflation pressure, established by Volvo, which is based on the type of tires

that are mounted on a vehicle at the factory. This inflation pressure is affected by the number of occupants in the car,the amount of cargo, and the speed at which the vehicle will be driven for a prolonged period. This information can befound on the tire inflation placard(s) located on the driver's side B-pillar or on the inside of the fuel filler door onCanadian models, and in the tire inflation table in this chapter.

Cold tires: The tires are considered to be cold when they have the same temperature as the surrounding (ambient)air. This temperature is normally reached after the car has been parked for at least 3 hours.


Vehicle loadingProperly loading your vehicle will provide maximum return of vehicle design performance. Before loading yourvehicle, familiarize yourself with the following terms for determining your vehicle's weight ratings, with or without atrailer, from the vehicle's Federal/Canadian Motor Vehicle Safety Standards (FMVSS/CMVSS) label, and the vehicle'stire information placard:

Curb weightThe weight of the vehicle including a full tank of fuel and all standard equipment. It does not include passengers,cargo, or optional equipment.

2006 VOLVO XC90


Capacity weightAll weight added to the curb weight, including cargo and optional equipment. When towing, trailer hitch tongue loadis also part of cargo weight.

NOTE: For trailer towing information, please refer to the section "Towing a trailer" on page 104.

Permissible axle weightThe maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on theFederal/Canadian Motor Vehicle Safety Standards (FMVSS/CMVSS) label. The total load on each axle must neverexceed its maximum permissible weight.Gross vehicle weight (GVW)The vehicle's curb weight + cargo + passengers.NOTE:

The location of the various labels in your vehicle can be found on page 172. A table listing important weight limits for your vehicle can be found on page 173.

Steps for Determining Correct Load Limit(1) Locate the statement "the combined weight of occupants and cargo should never exceed XXX pounds" on yourvehicle's placard.

(2) Determine the combined weight of the driver and passengers that will be riding in your vehicle.

(3) Subtract the combined weight of the driver and passengers from XXX kilograms or XXX pounds.

(4) The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the "XXX"amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo andluggage load capacity is 650 lbs. (1400-750 (5 x 150) = 650 lbs.)

(5) Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safelyexceed the available cargo and luggage load capacity calculated in Step 4.

(6) If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult thismanual1 to determine how this reduces the available cargo and luggage load capacity of your vehicle.

WARNING!- Exceeding the permissible axle weight, gross vehicle weight, or any other weight rating limits can cause tireoverheating resulting in permanent deformation or catastrophic failure.- Do not use replacement tires with lower load carrying capacities than the tires that were original equipment on thevehicle because this will lower the vehicle's GVW rating. Replacement tires with a higher limit than the originals donot increase the vehicle's GVW rating limitations.

1. See "Towing a trailer" on page 104


Uniform Tire Quality Grading

ALL PASSENGER VEHICLE TIRES MUST CONFORM TO FEDERAL SAFETY REQUIREMENTS INADDITION TO THESE GRADES

Quality grades can be found, where applicable, on the tire sidewall between the tread shoulder and maximum

2006 VOLVO XC90


section width. For example:Treadwear 200 Traction AA Temperature A

TREADWEARThe treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditionson a specified government test course. For example, a tire graded 150 would wear one and one half (1 1/2) times aswell on the government course as a tire graded 100. The relative performance of tires depends upon the actualconditions of their use, however, and many depart significantly from the norm due to variation in driving habits,maintenance practices and differences in road characteristics and climate.

TRACTIONThe traction grades, from highest to lowest, are AA, A, B, and C, as measured under controlled conditions on specifiedgovernment test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.

WARNING!The traction grade assigned to this tire is based on braking (straight-ahead) traction tests and is not a measure ofcornering (turning) traction.

TEMPERATUREThe temperature grades are AA (the highest), A, B, and C, representing the tire's resistance to the generation of heatand its ability to dissipate heat when tested under controlled conditions on specified indoor laboratory test wheel.Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessivetemperature can lead to sudden tire failure. The grade C corresponds to minimum level of performance that allpassenger vehicle tires must meet under the Federal Motor Safety Standard No. 109. Grades B and A represent higherlevels of performance on the laboratory test wheel than the minimum required by law.

WARNING!The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessivespeed, under-inflation, or excessive loading, either separately or in combination, can cause heat buildup and possibletire failure.


Snow chains, snow tire, studded tires

Snow chainsSnow chains can be used on your Volvo with the following restrictions:

Snow chains should be installed on front wheels only. Use only Volvo approved snow chains. If accessory, aftermarket or "custom" tires and wheels are installed and are of a size different than the original tires

and wheels, chains in some cases CANNOT be used. Sufficient clearances between chains and brakes, suspension andbody components must be maintained.

Some strap-on type chains will interfere with brake components and therefore CANNOT be used. All Wheel Drive models: Snow chains should only be installed on the front wheels. Only chains adapted for AWD

models should be used.

NOTE: Consult your Volvo retailer for additional snow chain information.

CAUTION- Check local regulations regarding the use of snow chains before installing.

2006 VOLVO XC90


- Always follow the chain manufacturer's installation instructions carefully. Install chains as tightly as possible andretighten periodically. - Never exceed the chain manufacturer's specified maximum speed limit. (Under no circumstances should youexceed 31 mph 50 km/h) - Avoid bumps, holes or sharp turns when driving with snow chains. - The handling of the vehicle can be adversely affected when driving with chains. Avoid fast or sharp turns as wellas locked wheel braking.

Snow tires, studded tires1

Tires for winter use:

- Owners who live in or regularly commute through areas with sustained periods of snow or icy driving conditions arestrongly advised to fit suitable winter tires to help retain the highest degree of traction.

- It is important to install winter tires on all four wheels to help retain traction during cornering, braking, andaccelerating. Failure to do so could reduce traction to an unsafe level or adversely affect handling.

- Do not mix tires of different design as this could also negatively affect overall tire road grip.

- Winter tires wear more quickly on dry roads in warm weather. They should be removed when the winter drivingseason has ended.

- Studded tires should be run-in 300-600 miles (500-1000 km) during which the car should be driven as smoothly aspossible to give the studs the opportunity to seat properly in the tires. The tires should have the same rotationaldirection throughout their entire lifetime.

NOTE: Please consult state or provincial regulations restricting the use of studded winter tires before installing suchtires.

1. Where permitted


Temporary Spare

The spare tire in your car is called a "Temporary Spare".

Recommended tire pressure (see the placard on the B-pillar or on the fuel filler door) should be maintained irrespectiveof which position on the car the temporary spare tire is used on. In the event of damage to this tire, a new one can bepurchased from your Volvo retailer.

WARNING!! Current legislation prohibits the use of the "Temporary Spare" tire other than as a temporary replacement for apunctured tire. It must be replaced as soon as possible by a standard tire. Road holding and handling may be affectedwith the "Temporary Spare" in use. Do not exceed 50 mph (80 km/h). Do not drive farther than 50 miles (80 km) ona temporary spare tire.

CAUTION:The car must not be driven with wheels of different dimensions or with a spare tire other than the one that came withthe car. The use of different size wheels can seriously damage your car's transmission.

2006 VOLVO XC90



Changing wheels

Changing wheels1

Location of jack - five-seat modelsThe jack is located to the right under the rear hatch in the cargo area floor. Lift this hatch and release the retainingstrap to lift out the jack. The rear section of the jack's crank is held in place behind the battery. The tool bag is storedto the left under the hatch. The front section of the crank is stored in the tool bag. The tool bag also contains a tool forremoving certain optional wheel covers. Consult your Volvo retailer.

NOTE: The rear section of the crank is enclosed in a protective sleeve that should be slid off before the crank is used.We recommend reinserting the crank into this sleeve before the crank is stowed.

If the vehicle is equipped with the optional grocery bag holder: Fold up the rear section of the cargo area floor,disconnect the grocery bag holder's retaining cords and fold up the lower section of the floor to access the tool bag.

Location of jack - seven-seat modelshatch in the cargo area floor. Lift this hatch and release the retaining strap to slide out the jack. The rear section of thejack's crank is held in place behind the battery. The tool bag is stored to the left under the hatch. The front section ofthe crank is stored in the tool bag.

NOTE: The rear section of the crank is enclosed in a protective sleeve that should be slid off before the crank is used.We recommend reinserting the crank into this sleeve before the crank is stowed.

If the vehicle is equipped with the optional grocery bag holder: Fold up the rear section of the cargo area floor,disconnect the grocery bag holder's retaining cords and fold up the lower section of the floor.

CAUTION: Seven-seat models: Do not store objects in the area for the rear seat cushions (when the backrests are tobe folded down). This could damage the cushions.

2006 VOLVO XC90


1. This applies to models not equipped with the tire sealing system (see page 130 for information).


Changing wheels (contd)

Changing wheels - lowering the spare wheelThe spare wheel is located under the floor of the rear cargo compartment. It can be lowered using the crank (seeprevious page for location).

WARNING!When raising or lowering the spare wheel, please keep in mind that components in the exhaust system may be veryhot.

Lowering the spare wheel:1. Fold down the lower section of the tailgate.2. Fold up the rear section of the floor in the cargo compartment.3. Connect the two sections of the jack's crank.4. Insert the hooked end of the crank in the spare wheel retaining attachment (see the illustration above).5. Lower the spare wheel under the vehicle by turning the crank counterclockwise until it is not possible to turn itfurther.6. Pivot the toggle at the end of the cable 90 degrees to release it from the spare wheel.7. Crank up the cable again by turning the crank clockwise.

CAUTIONWhen the spare wheel is mounted on the vehicle, the retaining cable could damage the underside of the vehicle if itis not retracted.

8. Place the wheel with the flat tire in the vehicle's cargo compartment.

NOTE: The space under the vehicle is designed to hold the special spare wheel only. Other full-size wheels will notfit in this compartment.


2006 VOLVO XC90


Returning the spare wheel to its storage compartment

1. Use the crank (turn it counterclockwise) to lower the spare wheel's retaining cable.2. Pass the toggle at the end of the cable through the center hole in the spare wheel. Pivot the toggle 90 degrees so thatwhen raised, the wheel will rest on the toggle.3. Retract the retaining cable slightly by slowly turning the crank clockwise several times.4. Position the wheel so that it is not obstructed by components in the exhaust system.5. Continue to raise the wheel by turning the crank clockwise.Raise the wheel a little bit at a time and guide it aroundthe rear axle until it is securely seated in the storage area.6. When it is no longer possible to turn the crank any further, check that the spare wheel is securely in position in thestorage compartment.


Changing wheels (contd)

Jack attachment points

Jack attachmentsThere are two attachment points for the jack on each side of the vehicle. These attachment points are under the centerof each door.

WARNING!- There is an attachment point on each side of the vehicle located under the pillars between the front and rear doors.This point is used during the production process only, and is NOT intended for attaching the jack.-The undersides of accessory running boards are not intended for attaching the jack.

2006 VOLVO XC90


Changing a wheel:1. Park the vehicle on a firm, level, non-slippery surface.2. Engage the parking brake and put the gear selector in the Park position.3. Loosen the wheel bolts by exerting downward pressure on the lug wrench.4. Remove the wheel cap (where applicable) using the lug wrench in the tool bag.5. With the wheels still on the ground, use the lug wrench to loosen the wheel bolts 1/2 - 1 turn. Turn the boltscounterclockwise to loosen the bolts.

CAUTION- The vehicle must not be driven with wheels of different dimensions or with a spare tire other than the one thatcame with the vehicle. The use of different size wheels can seriously damage your vehicle's transmission.- Correct tightening torque on wheel bolts must be observed.- The wheel bolts should never be greased or lubricated.- Extended, chromed wheel bolts must not be used with steel rims, as they make it impossible to fit the hub caps.


Attaching the jack Jack on certain models

6. Place the jack on the ground, under one of the attachment points (see the illustration on the previous page) andcrank while simultaneously guiding the jack's attachment bracket onto the attachment point (see illustration above) Thebase of the jack must be flat on a level, firm, non-slippery surface. Before raising the vehicle, check that the jack isstill correctly positioned in the attachment.

7. Raise the vehicle until the wheel to be changed is lifted off the ground.

8. Unscrew the wheel bolts completely and carefully remove the wheel so as not to damage the threads on the studs.

2006 VOLVO XC90


NOTE: To avoid excessive wear and the necessity of rebalancing, mark and reinstall wheels in the same location andposition as before removal. To lessen the chance of imbalance, each wheel hub is equipped with a guide stud to ensurethat a removed wheel can be reinstalled in its original position (as when changing over to winter tires/wheels).

Installing the wheel

1. Clean the contact surfaces on the wheel and hub.

2. Lift the wheel and place it on the hub.

3. Install the wheel bolts and tighten handtight. Using the lug wrench, tighten

4. Lower the vehicle to the ground and alternately tighten the bolts crosswise to 102 ft. lbs. (140 Nm).

5. Install the wheel cap (where applicable).

WARNING!- The jack must correctly engage the bar in the jack attachment. The vehicle's weight must not rest on the jackattachment. See illustration "Attaching the jack" above.- Be sure the jack is on a firm, level, non-slippery surface.- Never allow any part of your body to be extended under a vehicle supported by a jack.- Use the jack intended for the vehicle when replacing a wheel. For any other job, use stands to support the side ofthe vehicle being worked on.- Apply the parking brake and put the gear selector in the (P)ark position (or reverse on manual transmissions).- Block the wheels standing on the ground, use rigid wooden blocks or large stones. The jack should be kept well-greased.


Tire sealing system (option on certain models)

Location of tire sealing system - five-seat model

Tire sealing system Your vehicle may be equipped with a tire sealing system that enables you to temporarily seal a hole in the treadsurface and reinflate a flat tire, or to adjust a tire's inflation pressure.

The tire sealing system is located under the floor of the cargo compartment, see the illustrations above. Open the rearhatch on the cargo area floor to access the tire sealing system.

NOTE: The jack and crank shown in the illustrations above are optional on vehicles equipped with the tire sealingsystem.

The system consists of an air compressor, an integrated container for the sealing compound, wiring to connect the

2006 VOLVO XC90


system to the vehicle's electrical system via one of the 12-volt sockets1, and a hose used to connect the system to thetire's inflation valve.

Location of tire sealing system - seven-seat model

NOTE:

The tire sealing system is only intended to seal holes on the tire's tread area, not the sidewall.Tires with large holes or tears cannot be repaired with the tire sealing system.

WARNING!- After using the tire sealing system, the vehicle should not be driven farther than approximately 120 miles (200 km).Have the tire replaced as soon as possible. - The vehicle should not be driven faster than 50 mph (80 km/h) while using a tire that has been temporarily repairedwith the tire sealing system. - After using the tire sealing system, drive carefully and avoid abrupt steering maneuvers and sudden stops.

1. See pages 28 and 40 for the location of these sockets.


Temporarily repairing a flat tire Before using the tire sealing system, observe the following:

Be sure the vehicle is parked safely off the road and away from moving traffic.Apply the parking brake.Do not remove any foreign objects (nails, etc.) from the tire. Temporarily repairing a flat tire is done in two stages.In the first stage, the hole is sealed by pumping sealing compound into the tire. The car is then driven a short distance

to distribute the sealing compound in the tire.In the second stage, the tire's inflation pressure is checked and adjusted if necessary.

Stage 1: Sealing the hole1. Peel off the speed limit sticker (1) and affix it to the steering wheel hub where it will be clearly visible to the driver. 2. Ensure that the orange switch (2) is in position 0 (the 0 side of the switch should be pressed down). 3. Pull out the electrical wire (5) and hose (4) from the side compartment (3).

2006 VOLVO XC90


4. Remove the valve cap from the tire's inflation valve and screw the hose connector onto the valve as tightly aspossible by hand. 5. Connect the electrical wire to the nearest 12-volt socket in the vehicle. 6. Release the safety catch (6) and turn the orange colored section of the sealing kit (7), which holds the sealingcompound container, 90 degrees until it clicks into the vertical position. 7. Start the vehicle's engine. 8. Start the tire sealing system's compressor by pressing the switch (2) to position I.

NOTE: The air pressure gauge (9) will temporarily show an increase in pressure to approximately 88 psi (6 bar) whilethe sealing compound is being pumped into the tire. The pressure should return to a normal level after approximatelyone minute.

WARNING!- Never leave the tire sealing system unattended when it is operating. - Keep the tire sealing system kit away from children. - The vehicle's engine should be running when the tire sealing system is used to avoid battery drain. Therefore, besure the vehicle is parked in a well ventilated place before using the system.


WARNING!- Contact with the sealing compound may cause skin irritation. If contact occurs, wash the affected area immediatelywith soap and water. - Never stand next to the tire being inflated when the compressor is in operation. If cracks, bubbles, etc. form on thetire, switch off the compressor immediately. If there is visible damage to the sidewall or the rim, the tire cannot berepaired. The vehicle should not be driven if this occurs. Contact a towing service or Volvo On Call RoadsideAssistance if applicable.

9. Within seven minutes, inflate the tire to between 22 - 50 psi (1.8 - 3.5 bar). Switch off the compressor briefly to geta clear reading from the pressure gauge (9).

CAUTIONIf the pressure is below 22 psi (1.8 bar) after approximately seven minutes, turn off the compressor. In this case, thehole is too large to be sealed and the vehicle should not be driven.

10. Disconnect the electrical wire from the 12- volt socket. 11. Unscrew the hose from the tire's inflation valve and reinstall the valve cap. 12. Fold down the orange section of the tire sealing system to its original (horizontal) position and press the safetycatch into place. 13. Safely stow the tire sealing system kit in a convenient place as it will soon be used again to check the tire'sinflation pressure. 14. Immediately drive the vehicle for approximately 2 miles (3 km) to distribute the sealing compound in the tire.

WARNING!If heavy vibrations, unsteady steering behavior, or noises should occur while driving, reduce speed and park the carin a safe place. Recheck the tire for bumps, cracks, or other visible damage, and recheck its inflation pressure. If thepressure is below 16 psi (1.3 bar), do not continue driving. Have the vehicle towed to a workshop or Volvo retailer.

Stage 2: Checking inflation pressure

2006 VOLVO XC90


1. Park the car in a safe place. 2. Ensure that the orange switch (2) is in position 0 (the 0 side of the switch should be pressed down). 3. Remove the valve cap from the tire's inflation valve and screw the hose connector onto the valve as tightly aspossible by hand. 4. Connect the electrical wire to the nearest 12-volt socket in the vehicle. 5. Start the vehicle's engine. 6. Check the tire's inflation pressure on the gauge (9).

NOTE: In dark conditions, switching on the tire sealing system's compressor will illuminate the pressure gauge.

7. Inflate the tire to the correct pressure as indicated in the tire inflation tables on page 116. If the tire needs to beinflated, start the tire sealing system's compressor. If necessary, release air from the tire by pressing the vent button (8).

8. Turn off the compressor (press switch 2 to the 0 position) when the correct inflation pressure has been reached.

CAUTIONThe compressor should not be used for more than ten minutes at a time to avoid overheating.

9. Unscrew the hose from the tire's inflation valve and reinstall the valve cap. 10. Disconnect the electrical wire from the 12- volt socket. 11. Return the hose and electrical wire to the compartment on the side of the unit.

NOTE: When the tire sealing system has been used to seal a flat tire, the tank containing the sealing compound, andthe hose must be replaced. See the instructions on the following page. Contact a Volvo retailer for replacement parts.


Replacing the sealing compound container.

CAUTIONIf your vehicle is equipped with the optional Tire Pressure Monitoring System (see page 117), the use of the sealingcompound may lead to incorrect tire pressure readings or in rare cases, damage to the tire pressure sensor. Use thetire sealing system to check and adjust the damaged tire's pressure.

After use, return the tire sealing system to its storage area under the rear section of the cargo compartment floor.

WARNING!If you interrupt your trip for more than one hour, check the inflation pressure in the damaged tire again beforecontinuing. See the section "Stage 2: Checking inflation pressure" on the previous page.

Replacing the sealing compound container The sealing compound container must be replaced if:

the tire sealing system has been used to repair a tire

2006 VOLVO XC90


the container's expiration date has passed (see the date on decal 1). After use, the container (6), its retaining bracket (9), and the hose (10) must be replaced. Please consult your Volvoretailer for replacement parts.

NOTE: See also the safety regulations on the bottom of the container.

WARNING!Be sure that the compressor is not connected to a 12-volt socket while replacing the container.

Replacing the container and hose after use 1. Unscrew the two screws (2) on the orange casing.


2. Remove the speed limit sticker (4) and the expiration date decal (1). 3. Release the safety catch (5) and remove the casing (3) from the sealing system unit. 4. Press down the button (8) while twisting the container (6) and retaining bracket (9) clockwise approximately 2/3 of aturn and remove them. 5. To remove the hose (10), first press it into housing and then pull it out from the opposite side. 6. Wipe away any remaining sealing compound, or scrape it off if it has already hardened. 7. Insert a new air hose and check that it is properly seated. 8. Unscrew the cap from the new sealing compound container and check that the seal (7) is intact and undamaged. 9. Screw the container (6) firmly into the bracket (9). 10. Mount the bracket on the housing and twist it counterclockwise until it clicks into place. 11. Reinsert the casing (3). Check that it is correctly in place and tighten the screws (2), and press the safety catch (5)into position. 12. Affix the speed limit decal (4) and a new expiration date decal (1).

The empty container and used hose can be discarded as normal refuse, or recycled. Consult local regulations.

Replacing the container after its expiration date has passed1. Unscrew the two screws (2) on the orange casing. 2. Remove the speed limit sticker (4) and the expiration date decal (1). 3. Release the safety catch (5) and remove the casing (3) from the sealing system unit. 4. Unscrew and remove the container. 5. Unscrew the cap from the new sealing compound container and check that the seal (7) is intact and undamaged. 6. Screw the container (6) firmly into the bracket (9). 7. Reinsert the casing (3). Check that it is correctly in place and tighten the screws (2), and press the safety catch (5)into position. 8. Affix the speed limit decal (4) and a new expiration date decal (1).

The empty container can be discarded as normal refuse, or recycled. Consult local regulations.


2006 VOLVO XC90


2 0 0 6 VOLVO

XC90

Vehicle care

pg. 135 Vehicle care

Washing and cleaning the vehicle 136

Paint touch up 139


Washing and cleaning the vehicle

The vehicle should be washed at regular intervals since dirt, dust, insects and tar spots adhere to the paint and maycause damage. It is particularly important to wash the vehicle frequently in the wintertime to prevent corrosion, whensalt has been used on the roads.

When washing the vehicle, do not expose it to direct sunlight. Use lukewarm water to soften the dirt before youwash with a sponge, and plenty of water, to avoid scratching.

Bird droppings: Remove from paintwork as soon as possible. Otherwise the finish may be permanently damaged. A detergent can be used to facilitate the softening of dirt and oil. A water-soluble grease solvent may be used in cases of sticky dirt. However, use a wash place equipped with a

drainage separator.

CAUTIONIf the vehicle is equipped with chromeplated aluminum wheels, use only special car washing detergents to clean thewheels. Wheel cleaning agents can permanently stain chrome-plated wheels

Dry the vehicle with a clean chamois and remember to clean the drain holes in the doors and rocker panels. Tar spots can be removed with kerosene or tar remover after the vehicle has been washed. A stiff-bristle brush and lukewarm soapy water can be used to clean the wiper blades. Frequent cleaning improves

visibility considerably. Wash off the dirt from the underside (wheel housings, fenders, etc.). In areas of high industrial fallout, more frequent washing is recommended. After cleaning the engine, the spark plug wells should be inspected for water and blown dry if necessary.

Suitable detergents: Special vehicle washing detergents should be used. A suitable mixture is about 2.5 fl. oz. (8.5 cl)of detergent to 2.6 US gal. (10 liters) of warm water. After washing with a detergent the vehicle should be well rinsedwith clean water.

Exterior plastic components Cleaning exterior plastic components should be done with a cleaning agent specially designed for this purpose.Solvents or stain removers should not be used. Consult your Volvo retailer.

2006 VOLVO XC90


CAUTION- During high pressure washing, the spray mouthpiece must never be closer to the vehicle than 13" (30 cm). Do notspray into the locks.- When washing or steam cleaning the engine, avoid spraying water or steam directly on the electrical componentsor toward the rear side of the engine.Special moonroof cautions:- Always close the moonroof and visor before washing your vehicle.- Never use abrasive cleaning agents on the moonroof.- Never use wax on the rubber seals around the moonroof.

NOTE: When washing the vehicle, remember to remove dirt from the drain holes in the doors and sills.

WARNING!When the vehicle is driven immediately after being washed, apply the brakes several times in order to remove anymoisture from the brake linings.Engine cleaning agents should not be used when the engine is warm. This constitutes a fire risk.


Automatic washing - simple and quick

We do NOT recommend washing your vehicle in an automatic wash during the first six months (because the paintwill not have hardened sufficiently).

An automatic wash is a simple and quick way to clean your vehicle, but it is worth remembering that it may not beas thorough as when you yourself go over the vehicle with sponge and water. Keeping the underbody clean is mostimportant, especially in the winter. Some automatic washers do not have facilities for washing the underbody.

Before driving into an automatic car wash, make sure that side view mirrors, auxiliary lamps, etc, are secure, andthat any antenna(s) are retracted or removed. Otherwise there is risk of the machine dislodging them.

Polishing and Waxing

Normally, polishing is not required during the first year after delivery, however, waxing may be beneficial. Before applying polish or wax the vehicle must be washed and dried. Tar spots can be removed with kerosene or tar

remover. Difficult spots may require a fine rubbing compound. After polishing use liquid or paste wax. Several commercially available products contain both polish and wax. Waxing alone does not substitute for polishing a dull surface. A wide range of polymer-based waxes can be purchased today. These waxes are easy to use and produce a long-

lasting, high-gloss finish that protects the bodywork against oxidation, road dirt and fading. Do not polish or wax your vehicle in direct sunlight (the surface of the vehicle should not be warmer than 113° F

(45° C).

CAUTION:Volvo does not recommend the use of long-life or durable paint protection coatings, some of which may claim toprevent pitting, fading, oxidation, etc. These coatings have not been tested by Volvo for compatibility with yourvehicle's clear coat. Some of them may cause the clear coat to soften, crack, or cloud. Damage caused by applicationof paint protection coatings may not be covered under your vehicle's paint warranty.

Mirrors/side windows with the water repellent glass coating-option

Do not apply wax, degreasing agents, etc to this glass. This could damage the coating.

2006 VOLVO XC90


Clean the glass surface with care to avoid scratching. Use only suitable plastic scrapers to remove ice or snow from the windows.

NOTE: The water repellent coating is subject to natural wear.

In order to maintain the coating's water repellent characteristics, it should be treated with a special compound that isavailable at your Volvo retailer.

This treatment should be carried out for the first time after three years, and thereafter once a year.


Cleaning the upholstery

FabricClean with soapy water or a detergent. For more difficult spots caused by oil, ice cream, shoe polish, grease, etc., use aclothing/fabric stain remover. Consult your Volvo retailer.

Interior plastic components Cleaning interior plastic components should be done with a cleaning agent specially designed for this purpose. Consultyour Volvo retailer.

AlcanteraTM suede-like materialSuede-like upholstery can be cleaned with a soft cloth and mild soap solution.

Leather careVolvo's leather upholstery is manufactured with a protectant to repel soiling. Over time, sunlight, grease and dirt canbreak down the protection. Staining, cracking, scuffing, and fading can result.

Volvo offers an easy-to-use, non-greasy leather care kit formulated to clean and beautify your vehicle's leather, and torenew the protective qualities of its finish. The cleaner removes dirt and oil buildup. The light cream protectantrestores a barrier against soil and sunlight.

Volvo also offers a special leather softener that should be applied after the cleaner and protectant. It leaves leather softand smooth, and reduces friction between leather and other finishes in the vehicle.

Volvo recommends cleaning, protecting and conditioning your vehicle's leather two to four times a year. Ask yourVolvo retailer about Leather Care Kit 951 0251 and Leather Softener 943 7429.

CAUTION:- Under no circumstances should gasoline, naphtha or similar cleaning agents be used on the plastic or the leather sincethese can cause damage.- Take extra care when removing stains such as ink or lipstick since the coloring can spread.- Use solvents sparingly. Too much solvent can damage the seat padding.- Start from the outside of the stain and work toward the center.- Sharp objects (e.g. pencils or pens in a pocket) or velcro fasteners on clothing may damage the textile upholstery.

Cleaning the seat beltsClean only with lukewarm water and a mild soap solution.

Cleaning floor matsThe floor mats should be vacuumed or brushed clean regularly, especially during winter when they should be taken outfor drying. Spots on textile mats can be removed with a mild detergent.

2006 VOLVO XC90



Paint touch up

Paint damage requires immediate attention to avoid rusting. Make it a habit to check the finish regularly - whenwashing the vehicle for instance. Touch-up if necessary.

Paint repairs require special equipment and skill. Contact your Volvo retailer for any extensive damage.

Minor scratches can be repaired by using Volvo touch-up paint.

NOTE: When ordering touch-up paint from your Volvo retailer, use the paint code indicated on the model plate. Theplate is located in the engine compartment.

Color codeMake sure you have the right color. The color code number is on the data plate in the engine compartment.

Minor stone chips and scratchesMaterial:

Primer - can Paint - touch-up pen Brush Masking tape If the stone chip has not gone down to the bare metal and an undamaged color coat remains, you can add paint

immediately after removing dirt.

NOTE: When touching up the vehicle, it should be clean and dry. The surface temperature should be above 60° F (15°C).

Minor scratches on the surface If the stone chip has not penetrated down to the metal and an undamaged layer of paint remains, the touch-up paint canbe applied as soon as the spot has been cleaned.

Deep scratches1. Place a strip of masking tape over the damaged surface. Pull the tape off so that any loose flakes of paint adhere toit.

2. Thoroughly mix the primer and apply it with a small brush.

When the primer surface is dry, the paint can be applied using a brush. Mix the paint thoroughly; apply several thinpaint coats and let dry after each application.

2006 VOLVO XC90


3. If there is a longer scratch, you may want to protect surrounding paint by masking it off.




2006 VOLVO XC90


2 0 0 6 VOLVO

XC90

Maintenance

pg. 141 Maintenance

Volvo maintenance 142

Owner maintenance 143

Emission inspection readiness 144

Working on your vehicle 145

Engine compartment 147

Oils and fluids 148

Wiper Blades 152

Battery maintenance 153

Bulbs 156

Fuses 164

pg. 142 Maintenance

Volvo Maintenance

Maintenance ServicePeriodic maintenance will help keep your vehicle running well. Your Warranty and Service Records Informationbooklet provides a comprehensive maintenance schedule up to 150,000 miles (240,000 km) of vehicle service. Thismaintenance program contains inspections and services necessary for the proper function of your car, and includescomponents that affect vehicle emissions. The maintenance services contain several checks that require specialinstruments and tools and therefore must be performed by a qualified technician. Volvo advises you to follow theservice program outlined in this booklet. To keep your Volvo in top condition, specify time-tested and proven GenuineVolvo Parts and Accessories.

The Federal Clean Air Act - U.S.The Federal Clean Air Act requires vehicle manufacturers to furnish written instructions to the ultimate purchaser toassure the proper servicing and function of the components that control emissions. These services, which are listed inthe "Warranty and Service Records Information booklet," are not covered by the warranty. You will be required to payfor labor and material used.

MaintenanceYour Volvo passed several major inspections before it was delivered to you, in accordance with Volvo specifications.The maintenance outlined in the Warranty and Service Records Information booklet, many of which will positively

2006 VOLVO XC90


affect your vehicle's emissions, should be performed as indicated. It is recommended that receipts for vehicle emissionmaintenance be retained in case questions arise concerning maintenance.

Inspection and maintenance should also be performed anytime a malfunction is observed or suspected.

Applicable warranties - U.S./CanadaIn accordance with applicable U.S. and Canadian regulations, the following list of warranties is provided.

New Vehicle Limited Warranty Parts and Accessories Limited Warranty Corrosion Protection Limited Warranty Seat Belt and Supplemental Restraint Systems Limited Warranty Emission Design and Defect Warranty Emission Performance Warranty

These are the federal warranties; other warranties are provided as required by state/provincial law. Refer to yourseparate Warranty and Service Records Information booklet for detailed information concerning each of the warranties.

Vehicle Event Data (Black Box)Your vehicle's driving and safety systems employ computers that monitor, and share with each other, informationabout your vehicle's operation. One or more of these computers may store what they monitor, either during normalvehicle operation or in a crash or near-crash event. Stored information may be read and used by:

Volvo Car Corporationservice and repair facilitieslaw enforcement or government agenciesothers who may assert a legal right to know, or who obtain your consent to know such information.

pg. 143 Maintenance

Owner maintenancePeriodic maintenance requirements and intervals are described in your vehicle's Warranty and Service RecordsInformation booklet.

The following points can be carried out between the normally scheduled maintenance services.

Each time the car is refueled:

Check the engine oil level Clean the windshield, windshield wipers, headlights, and tail lights

Monthly:

Check cold tire pressure in all tires. Inspect the tires for wear. Check that engine coolant and other fluid levels are between the indicated "min" and "max" markings. Clean interior glass surfaces with a glass cleaner and soft paper towels. Wipe driver information displays with a soft cloth. Visually inspect battery terminals for corrosion. Corrosion may indicate a loose terminal connector, or a battery near

the end of its useful service life. Consult your Volvo retailer for additional information.

As needed:

Wash the car, including the undercarriage, to reduce wear that can be caused by a buildup of dirt, and corrosion thatcan be caused by salt residues.

Clean leaves and twigs from air intake vents at the base of the windshield, and from other places where they may

2006 VOLVO XC90


collect.

NOTE: Complete service information for qualified technicians is available online for purchase or subscription atwww.volvotechinfo.com.

pg. 144 Maintenance

Emission inspection readiness

What is an Onboard Diagnostic System (OBD II)? OBD II is part of your vehicle's computerized engine management system. It stores diagnostic information about yourvehicle's emission controls. It can light the Check Engine light (MIL) if it detects an emission control "fault." A "fault"is a component or system that is not performing within an expected range. A fault may be permanent or temporary.OBD II will store a message about any fault.

How do states use OBD II for emission inspections? Many states connect a computer directly to a vehicle's OBD II system. The inspector can then read "faults." In somestates, this type of inspection has replaced the tailpipe emission test.

How can my vehicle fail OBD II emission inspection? Your vehicle can fail OBD II emission inspection for any of the following reasons.

If your Check Engine (MIL) light is lit, your vehicle may fail inspection.If your vehicle's Check Engine light was lit, but went out without any action on your part, OBD II will still have a

recorded fault. Your vehicle may pass or fail, depending on the inspection practices in your area.If you had recent service that required disconnecting the battery, OBD II diagnostic information may be incomplete

and "not ready" for inspection. A vehicle that is not ready may fail inspection.

How can I prepare for my next OBD II emission inspection?

If your Check Engine (MIL) light is lit - or was lit but went out without service, have your vehicle diagnosed and, ifnecessary, serviced by a qualified Volvo technician.

If you recently had service for a lit Check Engine light, or if you had service that required disconnecting the battery,a period of driving is necessary to bring the OBD II system to "ready" for inspection. A half-hour trip of mixed stop-and-go/ highway driving is typically needed to allow OBD II to reach readiness. Your Volvo retailer can provide youwith more information on planning a trip.

Maintain your vehicle in accordance with your vehicle's maintenance schedule.

pg. 145 Maintenance

Working you your vehicle

http://www.volvotechinfo.com/

2006 VOLVO XC90


Reinforced lifting pointsHoisting the vehicleIf a garage jack is used to lift the vehicle, the two jack attachments points should be used. They are speciallyreinforced to bear the weight of the vehicle (see the illustration above). A garage jack can also be placed under thefront of the engine support frame. Take care not to damage the splash guard under the engine. Ensure that the jack ispositioned so that the vehicle cannot slide off it. Always use axle stands or similar structures. The car's gross vehicleweight is between 5770 lb (2630 kg) and 6080 lb (2760 kg). Use a jack and stands rated for this weight.

If a two-post hoist is used to lift the vehicle, the front and rear lift arm pads should be centered under the reinforcedlift plates on the inboard edge of the sill rail (see illustration).

Please note the following before you begin working on your vehicle:Battery (see also page 155 for more information on handling the battery)

Ensure that the battery cables are correctly connected and tightened. Never disconnect the battery when the engine is running (e.g. when replacing the battery). The battery contains acid that is both corrosive and poisonous. It is important that the battery is handled in an

environmentally friendly way. Let your Volvo retailer assist you. Never use a fast charger to charge the battery. The battery cables should be disconnected when recharging.

WARNING!The ignition system has very high voltage! The voltage in the ignition system is dangerous!

Do not touch spark plugs, ignition cables or the ignition coil when the engine is running or the ignition is switchedon!

The ignition should be switched off when: - Conducting engine tests. - Replacing parts in the ignition system, such as spark plugs, ignition coil, distributor, ignition cables, etc. - Never try to repair any part of the SRS/SIPS/WHIPS/IC systems yourself. Any interference in the system couldcause malfunction and serious injury. Any work should only be performed by an authorized Volvo workshop.

pg. 146 Maintenance

Belt checkCheck the belt regularly to make sure it is in good condition and is clean. A worn or dirty belt can cause poor coolingand low alternator output as well as impair the operation of the power steering and the air conditioning unit.

NOTE: The drive belt is equipped with a self-tensioning mechanism and requires no adjustment between changes.

WARNING!

2006 VOLVO XC90


The engine must not be running when this check is performed.

Check coolant levelThe cooling system must be filled with coolant and not leak to operate at maximum efficiency. Check the coolant levelregularly. The level should be between the "MAX" and "MIN" marks on the expansion tank. The check should bemade with particular thoroughness when the engine is new or when the cooling system has been drained.

Do not remove the filler cap other than for topping up with coolant. Frequent removal may prevent coolant circulationbetween the engine and the expansion tank during engine warm up and cooling.

Changing coolantNormally, the coolant does not need to be changed. If the system must be drained, consult your Volvo retailer.

NOTE: Do not top off with water only. This reduces the rust-protective and antifreeze qualities of the coolant and hasa lower boiling point. It can also cause damage to the cooling system if it should freeze. Top off with Volvo GenuineCoolant/Antifreeze only (a 50/50 mix of water and antifreeze).

CAUTIONThe cooling system must always be kept filled to the correct level. If it is not kept filled, there can be high localtemperatures in the engine which could result in damage. Different types of antifreeze/coolant may not be mixed.

WARNING!Never remove the radiator cap while the engine is warm. Wait until the vehicle cools.

pg. 147 Maintenance

Engine compartment

Engine compartment1. Brake fluid reservoir2. Relay/fuse box3. Air cleaner4. Cooling fan5. Radiator6. Dipstick - engine oil7. Filler cap - engine oil8. Washer fluid reservoir9. Power steering fluid reservoir10. Expansion tank - coolant

2006 VOLVO XC90


11. Data plate12. Battery (under floor in rear cargo area)

WARNING!The cooling fan (4) may start or continue to operate (for up to 6 minutes) after the engine has been switched off.

pg. 148 Maintenance

Oil and fluids

Oil specificationsEngine oil must meet the minimum ILSAC specification GF-3, API SL, or ACEA A1/B1. Lower quality oils may notoffer the same fuel economy, engine performance, or engine protection. Volvo recommends .

Depending on your driving habits, premium or synthetic oils may provide superior fuel economy and engineprotection. Consult your Volvo retailer for recommendations on premium or synthetic oils.

Oil additives must not be used.

NOTE: Synthetic oil is not used when the oil is changed when the normal maintenance is carried out. This oil is onlyused at customer request, at additional charge. Please consult your Volvo retailer.

Oil ViscosityOperation in hot climates.For the protection of your engine when temperatures in your area exceed 86° F (30° C), Volvo recommends that youuse an oil with suitable viscosity, as shown in the chart below.

Operation in temperate climatesIncorrect viscosity oil can shorten engine life. Under normal use when temperatures do not exceed 86° F (30° C), SAE5W-30 will provide good fuel economy and engine protection. See the viscosity chart above.

Extreme engine operationSynthetic oils meeting ACEA A5/B5 requirements are recommended for driving in areas of sustained temperatureextremes (hot or cold), when towing a trailer over long distances, and for prolonged driving in mountainous areas.

American Petroleum Institute (API) symbol

2006 VOLVO XC90


American Petroleum Institute (API) symbol

The API Service Symbol "donut" is divided into three parts: The upper section describes the oil's performance level. The center identifies the oil's viscosity. The lower section indicates whether the oil has demonstrated energy-conserving properties in a standard test in

comparison to a reference oil.

pg. 149 Maintenance

Changing engine oil and oil filterSee the previous page for oil specifications and page 176 for oil volumes. Refer to the Warranty and Service RecordsInformation booklet for information on the oil change intervals.

NOTE:

Volvo does not recommend the use of oil additives.Synthetic oil is not used when the oil is changed at the normal maintenance intervals except at ower request and at

additional charge. Please consult your Volvo retailer.

Checking and adding oil The oil level should be checked every time the vehicle is refueled. This is especially important during the period up tothe first scheduled maintenance service.

The car should be parked on a level surface when the oil is checked.If the engine is warm, wait for at least 10-15 minutes after the engine has been switched off before checking the oil.

Checking the oil 1. Pull out the dipstick and wipe it with a lintfree rag. 2. Reinsert the dipstick, pull it out, and check the oil level. 3. Add oil if necessary. If the level is close to the MIN mark, add approximately 1 US quart (1 liter) of oil. 4. Run the engine until it reaches normal operating temperature. 5. Switch off the engine and wait for at least 10-15 minutes and recheck the oil level. If necessary, add oil until thelevel is near the mark.

2006 VOLVO XC90


Oil level should be between the MIN and MAX marks on the dipstick

CAUTION- Not checking the oil level regularly can result in serious engine damage if the oil level becomes too low. - Never fill oil above the MAX mark. This could cause an increase in oil consumption. - Not checking the oil level regularly can result in serious engine damage if the oil level becomes too low. - Always add oil of the same type and viscosity as already used.

WARNING!Do not allow oil to spill onto or come into contact with hot exhaust pipe surfaces.

pg. 150 Maintenance

Oil and fluids (contd)

Washer fluid reservoir

Washer fluid reservoirThe washer fluid reservoir is located in the engine compartment and holds approx. 6.8 US qt (6.5 liters).When there is less than approximately 1 US qt (1 liter) remaining in the reservoir, the washer fluid spray will bedirected to the windshield only.During cold weather, the reservoir should be filled with windshield washer solvent containing antifreeze.

2006 VOLVO XC90


Coolant reservoirChanging coolantNormally, the coolant does not need to be changed. If the system must be drained, consult your Volvo retailer.

NOTE: Do not top off with water only. This reduces the rust-protective and antifreeze qualities of the coolant and hasa lower boiling point. It can also cause damage to the cooling system if it should freeze. Top off with Volvo GenuineCoolant/Antifreeze only (a 50/50 mix of water and antifreeze).

CAUTIONThe cooling system must always be kept filled to the correct level. If it is not kept filled, there can be high localtemperatures in the engine which could result in damage. Different types of antifreeze/coolant may not be mixed.Check coolant regularly!

WARNING!- Never remove the radiator cap while the engine is warm. Wait until the vehicle cools. - If it is necessary to top up the coolant when the engine is warm, unscrew the expansion tank cap slowly so that theoverpressure dissipates.

pg. 151 Maintenance

Oil and fluids (contd)

Brake fluid reservoirThe brake fluid should always be above the MIN mark on the side of the reservoir. Check, without removing the cap,that there is sufficient fluid in the reservoir.

2006 VOLVO XC90


Fluid type : DOT 4+ boiling point >536°F (280°C), P/N 9437433

Replace : Every second year or 30,000 miles (48,000 km). The fluid should be replaced once a year or every 15,000miles (24,000 km) when driving under extremely hard conditions (mountain driving, etc.)

Always entrust brake fluid changing to an authorized Volvo retailer.

Power steering fluid reservoirThe fluid level should always be between the ADD and FULL marks.

Fluid type : Volvo synthetic power steering fluid (Pincushion CHF 11S) P/N 1161529 or equivalent.

Replace : No fluid change required

NOTE: If a problem should occur in the power steering system or if the vehicle has no electrical current and must betowed, it is still possible to steer the vehicle. However, keep in mind that greater effort will be required to turn thesteering wheel.

pg. 152 Maintenance

Wiper blades

Windshield wiper blades1. Lift the wiper arm off the windshield.

2006 VOLVO XC90


2. Press in the catches (A in the illustration above).3. Pull out the wiper blade.4. Insert a new wiper blade and ensure that it is firmly in place.NOTE: The driver's side wiper blade is longer than the one on the passenger's side.

Tailgate wiper blade1. Pull the wiper blade out, away from the tailgate window.2. Pull the wiper blade outward, toward the tailgate.3. Press the new wiper blade into place. Check that it is properly secured.


2006 VOLVO XC90


2 0 0 6 VOLVO

XC90

Specifications

pg. 171 Specifications

Label information 172

Weights 173

Dimensions 174

Fluid capacities 175

Engine oil 176

Lubricants 177

Electrical system 179

Engine specifications 180

All specifications are subject to change without prior notice.


2006 VOLVO XC90


Label information

1. Vehicle Emission Control InformationYour Volvo is designed to meet all applicable emission standards, as evidenced by the certification label on theunderside of the hood. For further information regarding these regulations, please consult your Volvo retailer.

2. Vacuum hose routing(underside of hood)

3. Loads and Tire Pressures(on inside of fuel filler door). Canadian models only.

4. Child safety lock label

5. Federal Motor Vehicle Safety Standards (FMVSS) specifications (USA) and Ministry of Transport (CMVSS) standards (Canada) Your Volvo isdesigned to meet all applicable safety standards, as evidenced by the certification label on the facing side of the driver'sdoor. For further information regarding these regulations, please consult your Volvo retailer.

6. Loads and Tire Pressures U.S. models only Certain models will only have one decal, depending on the specifications of the vehicle.

7. Vehicle Identification Number (VIN)1 The VIN plate is located on the top left surface of the dashboard. The VIN is also stamped on the right hand doorpillar.

8. Model plate Vehicle Identification Number (VIN). Codes for color and upholstery, etc. The plate is located in the enginecompartment, on the inside of the left front fender.

2006 VOLVO XC90


1. The Vehicle Identification Number (VIN) should always be quoted in all correspondence concerning your vehiclewith the retailer and when ordering parts.


Weights

Gross vehicle weight* USA Canada5-seat, 5-cyl, FWD 5640 lbs -5-seat, 5-cyl, AWD 5790 lbs 2630 kg5-seat, 8-cyl, AWD 5900 lbs 2680 kg7-seat, 5-cyl, FWD 5840 lbs -7-seat, 5-cyl, AWD 6005 lbs 2720 kg7-seat, 8-cyl, AWD 6080 lbs 2760 kgCapacity weight5-seat models 1160 lbs 525 kg7-seat models 1210 lbs 550 kgPermissible axle weight, front*5-seat, 5-cyl, FWD 2710 lbs -5-seat, 5-cyl, AWD 2820 lbs 1280 kg5-seat, 8-cyl, AWD 2910 lbs 1320 kg7-seat, 5-cyl, FWD 2710 lbs -7-seat, 5-cyl, AWD 2820 lbs 1280 kg7-seat, 8-cyl, AWD 2910 lbs 1320 kg

FWD = Front Wheel DriveAWD = All Wheel Drive* Permissible axle weight or gross vehicle weight must never be exceeded.

Permissible axle weight, rear* USA Canada5-seat, 5-cyl, FWD 3060 lbs -5-seat, 5-cyl, AWD 3150 lbs 1430 kg5-seat, 8-cyl, AWD 3150 lbs 1430 kg7-seat, 5-cyl, FWD 3170 lbs -7-seat, 5-cyl, AWD 3240 lbs 1470 kg7-seat, 8-cyl, AWD 3240 lbs 1470 kgCurb weight5-seat, FWD 4355-4390 lbs -5-seat, AWD 4490-4670 lbs 2045-2125 kg7-seat, FWD 4530-4565 lbs -7-seat, AWD 4665-4830 lbs 2115-2190 kgMax. roof load 220 lbs 100 kgTrailer weight, w/o brakes 1700 lbs 750 kgTrailer weight, with brakes See the table on page 104

2006 VOLVO XC90


Max. tongue weight See the table on page 104


Dimensions

DimensionsLength 188.9 in (479.8 cm)Width 74.7 in (189.8 cm)Height 70.2 in (178.4 cm)Wheelbase 112.6 in (285.7 cm)Front track 64.3 in (163.4 cm)Rear track 63.9 (162.4 cm)Turning circle 39-40 ft. (11.9-12.3 m)

Cargo capacityWith optional 3rd row of seats folded down:5-seat: 41.6 cu ft (1178 litres)7-seat: 43.3 cu ft (1225 litres)

Behind 1st row of seats, with 2nd (and optional 3rd) row of seats folded down:5-seat: 84.9 cu ft (2403 litres)7-seat: 85.1 cu ft (2410 litres)

Behind 1st row of seats, with front passenger seat, 2nd row (and optional 3rd row) of seats folded down:5-seat: 92.0 cu ft (2606 litres)7-seat: 93.2 cu ft (2640 litres)


Fluid Capacities

Fuel tank 21.1 US gallons (80 liters). Minimum octane requirement - AKI 87 (RON 91) - unleaded fuel (See also page 86)

Transmission oilAW55-51 (5-cyl. turbo) 7.6 US qts. (7.2 liters) JWS 3309TF-80SC (V8) 7.4 US qts. (7.0 liters) JWS 3309MiscellaneousPower steering 1.1 US qts. (1.0 liters)Windshield washer reservoir 6.9 US qts. (6.5 liters)Brake fluid 0.63 US qts. (0.6 liters)Air conditioning system Front - 2.2 lb. (1 kg), Rear (option) 2.9 lb. (1.3 kg) R 134a (HFC134a)

WARNING!When adding accessories, equipment, luggage and other cargo to your vehicle, the total capacity weight must not beexceeded.

2006 VOLVO XC90



Engine oil

SpecificationsEngine oil must meet the minimum ILSAC specification GF-3, API SL, or ACEA A1/B1. Lower quality oils may notoffer the same fuel economy, engine performance, or engine protection.

VolumeEngine designation Volume between MIN-MAX on dipstick Volumea

2.5T B5254T2 1.3 US qts (1.2 liters) 5.8 US qts. (5.5 liters)V8 AWD B8444S 1.3 US qts (1.2 liters) 7.1 US qts. (6.7 liters)

a. Including filter replacement


Lubricants

TransmissionOil grade: See the table on page 175.

Different types of oil should never be mixed.

Power steeringGrade: Volvo synthetic power steering fluid (Pentosin CHF 11S) P/N 1161529 or equivalent.

Brake fluidFluid type: DOT 4+ boiling point >536°F (280°C), P/N 9437433

Cooling system

Type Positive pressure, closed system.Coolant Volvo original coolant/antifreeze

Volume 5-cyl. turbo 9.5 US qts. (9.0 liters)V8 10.7 US qts. (10.2 liters)

The thermostat begins to open at 194°F (90°C).

Suspension

2006 VOLVO XC90


Rear suspensionIndividual rear wheel suspension with longitudinal support arms, double link arms and track rods.

Front suspensionSpring strut suspension with integrated shock absorbers and control arms linked to the support frame. Power-assistedrack and pinion steering. Safety type steering column.


Three-way catalytic converter cautions

Keep your engine properly tuned. Certain engine malfunctions, particularly involving the electrical, fuel ordistributor ignition systems, may cause unusually high three-way catalytic converter temperatures. Do not continue tooperate your vehicle if you detect engine misfire, noticeable loss of power or other unusual operating conditions, suchas engine overheating or backfiring. A properly tuned engine will help avoid malfunctions that could damage the three-way catalytic converter.

Do not park your vehicle over combustible materials, such as grass or leaves, which can come into contact with thehot exhaust system and cause such materials to ignite under certain wind and weather conditions.

Excessive starter cranking (in excess of one minute), or an intermittently firing or flooded engine can cause three-way catalytic converter or exhaust system overheating.

Remember that tampering or unauthorized modifications to the engine, the Electronic Control Module, or the vehiclemay be illegal and can cause three-way catalytic converter or exhaust system overheating. This includes:- Altering fuel injection setting or components.- Altering emission system components or location or removing components.- Repeated use of leaded fuel.

NOTE: Unleaded fuel is required for vehicles with three-way catalytic converters.


Electrical system

12-volt system with voltage controlled generator. Single wire system in which the chassis and engine block are used asconductors, grounded on the chassis.Battery 2.5T V8Voltage 12 V 12 VCold start capacity (CCA) 600 A 600 AReserve capacity (RC) 120 min 120 min

If you must replace your battery, be sure to replace it with a battery of the same cold start capacity and reservecapacity as the original (See the decal on the battery).

Generator max. current 140 A* 170 AStarter motor, power 1.4 kW 2.0 kWSpark plugs P/N272313-8 or equivalentGap 0.028 in. 0.7 mmTightening torque 22 ft. lbs. (30 Nm)

* Models equipped with the optional rear A/C unit have 160 A generators.

2006 VOLVO XC90



Engine specifications,

B5254T2 B8444SOutput (kW/rps) 154/83 232/100- (hp/rpm) 208/5000 311/6000Torque (Nm/rps) 320/1500-4500 440/3900- (ft. lbs./rpm) 236/1500-4500 325/3900No. of cylinders 5 8Bore (in./mm) 3.27/83 3.7/94Stroke (in./mm) 3.67/93.2 3.13/79.5Cylinder displacement, liters 2.52 (153.8 cu in) 4.41 (268.6 cu. in.)Compression ratio 9.0:1 10.4:1

Charge air cooler (Intercooler)Turbocharged engines employ a turbo-compressor to force air into the engine inlet manifold and a charge air cooler tocool the compressed inlet air. The resulting increase in air flow raises pressure in the intake manifold and increasesengine power over that developed by the normally-aspirated engine. The charge air cooler (which resembles a radiator)is located between the turbo-compressor and inlet manifold.

Fuel systemThe engine is equipped with a multiport fuel injection system.


Volvo On Call Roadside AssistanceYour new Volvo comes with a four year ON CALL roadside assistance. Additional information, features, and benefitsare described in a separate information package in your glove compartment.

If you have misplaced your package, dial:In the U.S.A.1-800-638-6586 (1-800-63-VOLVO)In Canada:1-800-263-0475

Technician certificationIn addition to Volvo factory training, Volvo supports certification by the National Institute for Automotive ServiceExcellence (A.S.E.). Certified technicians have demonstrated a high degree of competence in specific areas. Besidespassing exams, each technician must also have worked in the field for two or more years before a certificate is issued.These professional technicians are best able to analyze vehicle problems and perform the necessary maintenanceprocedures to keep your Volvo at peak operating condition.



2006 VOLVO XC90



2006 VOLVO XC90


2 0 0 6 VOLVO

XC90

Index

pg. 207-211 Index

AA/C (air conditioning) 55ABS ii, 23, 97Air cleaner 147Air distribution 52, 55Air Quality sensor 56Air vents 52Alarm 82All Wheel Drive 95All Wheel Drive - towing 102Anchorages, for child seats 20Anti-lock Brake System (ABS) ii, 23Approach lighting 77Ashtray 40, 68Audio system 183AUTO (climate control) 54Automatic climate control, ECC 53Automatic gearbox 91Autostart 90Auxiliary 12-volt sockets 40Auxiliary lights 27Average speed 37AWD 95BBass 189Battery 145, 152, 179Battery - replacing 154Battery drain - avoiding 92Battery maintenance 153Belt check 146Black box (Vehicle Event Data) 142Blower (fan) 54Booster cushion, integrated18

2006 VOLVO XC90


Brake system 24, 96Bulbs, list of 156Bulbs, replacing 157CCapacities 175Capacity weight 121Carbon Monoxide - Important Warning 87Cargo capacity 174Catalytic converter 178CD changer 201CD eject 200CD Pause 199CD player 199Ceiling lighting 162Center console - storage compartments 68Central locking system - remote control 77Changing a wheel 128Changing coolant 146Check Engine warning light 25Child booster cushion 18Child restraint anchorages 20Child safety locks 81Child seat anchors 20Cleaning the upholstery 138Climate control systems - general information 50Clock 22Coat hanger 70Coin compartment 68Cold tires, definition 114Cold weather precautions 108Coolant - changing 146, 150Coolant - checking level of 146Cooling system 177Courtesy light 65Cruise control 38Cup holder 68, 69Cup holder in rear seat 68Curb weight 121Current fuel consumption 37DDefroster 54Dimensions 174Dolby Pro Logic II (DPL II) 189Door mirror defroster 36

2006 VOLVO XC90


Driving economically 91DSTC 27, 98EECC 53Economical driving 91Electric socket 27Electrical current - conserving 92Electrical sockets, 12-volt 40Electrical system 179Electronic Brake Force Distribution 97Emergency Brake Assistance 97Emission inspection readiness 144Engine - starting 89Engine compartment 147Engine oil, changing 149Engine oil, specifications 148, 176Engine oil, volume 176Engine specifications 180Environment iiiFFader 189Federal Clean Air Act 142FIX NEXT SERVICE 26Flat tire, changing 125Flat tire, tire sealing system 130Floor mats 66Fog light symbol (rear) 25Folding sideview mirrors 27Front park assist 100Front seat, folding backrest 59Front seats 58Front seats - heated 36Front seats - manual adjustment 58Front seats - power 60Front suspension 177Fuel ii, 86Fuel filler cap ii, 88Fuel filler door ii, 88Fuel filler door - unlocking manually 30Fuel Formulations 87Fuel gauge 22Fuel tank, capacity 175Fuses 164G

2006 VOLVO XC90


Gasoline 86Geartronic 93Geartronic - manual shifting 94General information iiGenerator warning light 25Glove compartment 69HHandling 92Hazard warning flashers 36Headlight washer 34Headphones 186Heated front seats 36, 55High beam indicator 22High/low beam headlights 32High/low beams - replacing 157Hoisting the car 145HomeLink® Universal Transceiver 204Hood - opening 41IImmobilizer (start inhibitor) 76Indicator and warning symbols 22, 23Inflatable Curtain 13Inflation pressure table 116Inspection readiness 144Instrument panel 22Integrated child booster cushion 18Interior Air Quality sensor 56Interior lighting 65Intermittent wiping 33Introduction iISOFIX/LATCH anchors 20JJacking your vehicle 125Jump starting 103KKeylock ii, 89Keys 76LLabel information 172LATCH anchors 20Leather care (upholstery) 138Lighting panel 29Locking steering wheel 90Locking the vehicle 79

2006 VOLVO XC90


Locks 75Long distance trips 109Low/high beam headlights 32Lubricants 177MMaintenance services 142Maintenance, periodic 143Malfunction indicator light 25Memory function, mirrors 44Messages in the display 26Mirror memory function 44Mirror, rearview 44Mirrors - sideview, adjusting 44Mirrors - sideview, folding 27Moonroof 46Multifilter with air quality sensor 56OOccupant Weight Sensor 8Octane rating 86Odometer 22Oil pressure 25Oil quality 148Oil specifications 176Oil viscosity 148Oil volume 176Oil, changing 149Opening the hood 42Owner maintenance 143PP Park 93Paint - color code 139Paintwork damage 139Park assist 100Parking brake 25, 41Periodic owner-performed maintenance 143Permissible axle weight 121Polishing 137Power moonroof 46Power seat 60Power steering fluid 151PremAir® iiiProgram Information (PI) Seek 195PROPOSITION 65 WARNING 103, 155R

2006 VOLVO XC90


Radiator 147Radio Broadcast Data System (RBDS) 195Rain sensor - windshield wipers 33Reading lamps 65Rear park assist 100Rear seat air conditioning 27Rear suspension 177Rear window defroster 36Rearview mirror/door mirrors 44Recirculation 55REDUCE SPEED 26Refrigerant (A/C system) 50Refueling 86, 88Remote control - central locking system 77Repairing flat tires, ire sealing system 130Reporting safety defects 2Restraint anchorages, for child seats 20Roadholding 92Roll Stability Control (RSC) 98SSafety 1Safety defects - reporting 2Sealing system, repairing flat tires 130Seat belt 3Seat belt maintenance 2Seat belt reminder 44Service 142Service key 76Service reminder 25SERVICE REQUIRED 26SERVICE URGENT 26Shiftlock ii, 89Sideview mirrors, adjusting 44Sideview mirrors, folding 27Spare tire - accessing 126Spare wheel, lowering 126Spark plugs 179Specifications 171Speedometer 22Start inhibitor (immobilizer) 76Starting the car 89Steering wheel adjustment 31Steering wheel lock 90Stone chips, touching up 139

2006 VOLVO XC90


STOP 26STOP ENGINE 26Storage compartments 68Supplemental Restraint System (SRS) - warning light 25Suspension 177, 179Switches in the center console 27TTachometer 22Tailgate - locking/unlocking 80Tailgate wiper 35Tailgate wiper blades 152Temperature control 54Temperature gauge 22Text window - messages 26Three-way catalytic converter 178TIME FOR REGULAR SERVICE 26Tire designations 119Tire inflation 114Tire inflation pressure table 116Tire Pressure Monitoring System 25, 117Tire pressure, checking 114Tire sealing system 130Tire terminology 120Tires, changing 125Tires 113Towing 101Towing - cars with All Wheel Drive 102Towing a trailer 104Towing a trailer - V8-engine 106Trailer indicator lamp 25Trailer towing 104Transmission - Geartronic 93Tread wear indicator 112Treble 189Trip computer 37Trip odometer 22UUniform Tire Quality Grading 129Unlocking the vehicle 79Upholstery, cleaning 138VV8 engine and trailer towing 106Valet key 76Vanity mirror 66

2006 VOLVO XC90


Vehicle Event Data 142Vehicle Identification Number (VIN) 172Vehicle loading 121VIN (Vehicle Identification Number) 172Volvo and the environment iiiWW - Winter 94Warning symbol in center of dashboard 23Warranties 142Washer fluid reservoir 147, 150Washing the car 136Water repellent glass 45, 137Waxing 137Weights 173Windows, power 42Windshield wiper blades, replacing 152Windshield wipers 33Windshield wipers (rain sensor function) 33Winter/Wet driving mode 108Wiper, tailgate 35

Back cover

Accessory Installation - Important Warning

We strongly recommend that Volvo owners install only genuine, Volvo-approved accessories, and that accessoryinstallations be performed only by the factory-trained technicians at your authorized Volvo retailer.

Genuine Volvo accessories are tested to ensure compatibility with the performance, safety, and emission systems inyour vehicle. Additionally, your authorized Volvo retailer knows where accessories may and may not be safelyinstalled in your Volvo. In all cases, please consult your authorized Volvo retailer before installing any accessory in oron your vehicle.

Accessories that have not been approved by Volvo may or may not be specifically tested for compatibility with yourvehicle. Additionally, an inexperienced installer may not be familiar with some of your vehicle's systems.

Any of your vehicle's performance and safety systems could be adversely affected if you install accessories thatVolvo has not tested, or if you allow accessories to be installed by someone unfamiliar with your vehicle.

Damage caused by unapproved or improperly installed accessories may not be covered by your new vehiclewarranty. See your Warranty and Service Records Information booklet for more warranty information. Volvo assumesno responsibility for death, injury, or expenses that may result from the installation of non-genuine accessories.

Driver Distraction

Driver distraction results from driver activities that are not directly related to controlling the vehicle in the drivingenvironment. Your new Volvo is, or can be, equipped with many feature-rich entertainment and communicationsystems. These include hands-free cellular telephones, navigation systems, and multipurpose audio systems. You mayalso own other portable electronic devices for your own convenience. When used properly and safely, they enrich thedriving experience. Improperly used, any of these could cause a distraction.

For all of these systems, we want to provide the following warning that reflects the strong Volvo concern for yoursafety:

Never use these devices or any feature of your vehicle in a way that distracts you from the task of driving safely.

2006 VOLVO XC90


Distraction can lead to a serious accident.In addition to this general warning, we offer the following guidanceregarding specific newer features that may be found in your vehicle:

Never use a hand-held cellular telephone while driving. Some jurisdictions prohibit cellular telephone use by adriver while the vehicle is moving.

If your vehicle is equipped with a navigation system, set and make changes to your travel itinerary only with thevehicle parked.

Never program your audio system while the vehicle is moving. Program radio presets with the vehicle parked, anduse your programmed presets to make radio use quicker and simpler.

Never use portable computers or personal digital assistants while the vehicle is moving. A driver has a responsibilityto do everything possible to ensure his or her own safety and the safety of passengers in the vehicle and others sharingthe roadway. Avoiding distractions is part of that responsibility.

The following should be checked regularly:*1. Washer fluid reservoir should be filled with water and solvent (wintertime: windshield washer anti-freeze). See page150.2. Power steering - When cold, the level must not be above the COLD mark and when hot it must not be above theHOT mark. Top up if the level drops to the ADD mark with ATF fluid. See page 151.3. Coolant level should be between the expansion tank marks. Mixture: 50% antifreeze and 50% water. See page 150.4. Engine oil should be checked each time the vehicle is refueled. The oil level should be between the dipstick marks.The distance between the marks represents approx. 1.6 US qt. (1.5 liter). See page 148.5. Brake fluid - check, without removing the cap, that the level is above the MIN mark. Use brake fluid DOT 4+. Seepage 151.

Fuel octane rating, see page 86.

Tire pressure, see page 114, and the label located on the inside of the fuel tank cover.

1 Turn signal2 High beam3 Parking light4 Low beam5 Fog light, front6 Fog light, rear7 Back-up light8 Parking light/tail light9 Turn signal10 Brake light

See page 156 for more information on replacing bulbs.

2006 VOLVO XC90



2006 VOLVO XC90



Brake system

BRAKE Brake circuit malfunctionThe brake system is a hydraulic system consisting of two master cylinders and two separate brake circuits. If aproblem should occur in one of these circuits, it is still possible to stop the vehicle with the other brake circuit.

If the brake pedal must be depressed farther than normal and requires greater foot pressure, the stopping distance willbe longer.

A warning light in the instrument panel will light up to warn the driver that a fault has occurred.

If this light comes on while driving or braking, stop immediately and check the brake fluid level in the reservoir.

NOTE: Press the brake pedal hard and maintain pressure on the pedal - do not pump the brakes.

WARNING!If the fluid level is below the MIN mark in the reservoir or if a "Brake failure - Service urgent" message is displayedin the text window: DO NOT DRIVE. Have the vehicle towed to a Volvo retailer and have the brake systeminspected.

NOTE: When the vehicle is at a standstill and the engine is idling, e.g. at a traffic light and the brake pedal isdepressed, the pedal may go down slightly. This is a normal function of the power-assisted brake system.

Power brakes function only when the engine is runningThe power brakes utilize vacuum pressure which is only created when the engine is running. Never let the vehicle rollto a stop with the engine switched off.

If the power brakes are not working, the brake pedal must be pressed approximately four times harder than usual tomake up for the lack of power assistance. This can happen for example when towing your vehicle or if the engine isswitched off when the vehicle is rolling. The brake pedal feels harder than usual.

Water on brake discs and brake pads affects brakingDriving in rain and slush or passing through an automatic car wash can cause water to collect on the brake discs andpads. This will cause a delay in braking effect when the pedal is depressed. To avoid such a delay when the brakes areneeded, depress the pedal occasionally when driving through rain, slush, etc. This will remove the water from thebrakes. Check that brake application feels normal. This should also be done after washing or starting in very damp orcold weather.

Severe strain on the brake systemThe brakes will be subject to severe strain when driving in mountains or hilly areas, or when towing a trailer. Vehiclespeed is usually slower, which means that the cooling of the brakes is less efficient than when driving on level roads.To reduce the strain on the brakes, shift into a lower gear and let the engine help with the braking. Do not forget that ifyou are towing a trailer, the brakes will be subjected to a greater than normal load.


Brake system (contd)

2006 VOLVO XC90


Anti-lock brakes (ABS)

If the warning lamp lights up there is a malfunction of the ABS system (the standard braking system will howeverfunction) and the vehicle should be driven cautiously to a Volvo retailer for inspection. The Anti-lock Braking System(ABS) helps to improve vehicle control (stopping and steering) during severe braking conditions by limiting brakelockup. When the system "senses" impending lockup, braking pressure is automatically modulated in order to helpprevent lockup, which could lead to a skid.

This system performs a self-diagnostic test when the engine is started and when the vehicle first reaches a speedof approximately 12 mph (20 km/h). The brake pedal will pulsate several times and a sound may be audible from theABS control module. This is normal.

To obtain optimal effect from the ABS system, constant pressure should be kept on the brake pedal. Do not pump thebrake pedal.

The switching of the ABS modulator will be audible and the brake pedal will pulsate during braking. Please be awarethat ABS does not increase the absolute braking potential of the vehicle. While control will be enhanced, ABS will notshorten stopping distances on slippery surfaces.

ABS with EBD (Electronic Brake Force Distribution)EBD is an integrated part of the ABS system. EBD regulates the hydraulic pressure to the rear brakes to help provideoptimal braking capacity. The brake pedal will pulsate during braking, which is normal.

If the BRAKE and ABS warning lights come on at the same time, this could indicate a fault in the brake system.

Stop the vehicle in a suitable place and switch off the engine.Restart the engine.If both warning lights go off, no further action is required.If both lights are still on after the engine has been restarted, switch off the engine again and check the brake fluid

level (see page 147 for the location of the brake fluid reservoir).If the brake fluid level is above the MIN mark, drive carefully to an authorized Volvo retailer and have the brake

system inspected.

WARNING!If the fluid level is below the MIN mark in the reservoir or if a "Brake failure - Service urgent" message is displayedin the text window: DO NOT DRIVE. Have the vehicle towed to a Volvo retailer and have the brake systeminspected.

Emergency Brake Assistance (EBA)EBA is designed to provide full brake effect immediately in the event of sudden, hard braking. The system is activatedby the speed with which you depress the brake pedal.

NOTE:

When the EBA system is activated, the brake pedal will go down and pressure in the brake system immediatelyincreases to the maximum level. You must maintain full pressure on the brake pedal in order to utilize the systemcompletely. EBA is automatically deactivated when the brake pedal is released.

When the vehicle has been parked for some time, the brake pedal may sink more than usual when the engine isstarted. This is normal and the pedal will return to its usual position when it is released.


2006 VOLVO XC90


Dynamic Stability Traction Control (DSTC)

The DSTC system on the Volvo XC90 consists of a number of functions:

1. Traction control (TC)This function is designed to help reduce wheel spin by transferring power from a drive wheel that begins to losetraction to the wheel on the opposite side of the vehicle (on the same axle). TC monitors and compares the rotationalspeed of the drive wheels. If one of the drive wheels shows a tendency to spin, the difference in speed is immediatelydetected. This triggers the Anti-lock Brake System, which brakes the spinning wheel until the difference in rotationalspeed is corrected.

TC is most active at low speeds, and a pulsating sound will be audible when the system is regulating wheel spin. Thisis quite normal.

This is one of the DSTC system's permanent functions and is not affected when the DSTC button on the center controlpanel is pressed.

2. Spin control (SC)The spin control function is designed to help prevent the drive wheels from spinning while the vehicle is accelerating.This is done by temporarily reducing engine torque to the drive wheels, which helps improve tractive force.

Under certain circumstances, such as when driving with snow chains, or driving in deep snow or loose sand, it may beadvisable to temporarily switch off this function for maximum tractive force. This is done by pressing the DSTC buttonon the center control panel for at least a half a second.

When the SC function has been switched off:

The text window will briefly display "DSTC SPIN CONTROL OFF"The LED in the DSTC button will be off.

3. Active Yaw Control (AYC)This function helps maintain directional stability, for example when cornering, by braking one or more of the wheels ifthe vehicle shows a tendency to skid or slide laterally. This is done by activating the Anti-lock Braking System. Apulsating sound will be audible when the function is active, which is quite normal. If you apply the brakes while thisfunction is active, the brake pedal will feel stiffer than usual.

This is also one of the DSTC system's permanent functions and is not affected when the DSTC button on the centercontrol panel is pressed.

4. Roll Stability Control (RSC)RSC utilizes a gyro-sensor to monitor the vehicle's angle of inclination, and the rate at which this angle changes. Ifnecessary, RSC activates the Anti-lock Brake System to brake one or more of the wheels to help maintain stability. Apulsating sound will be audible when the function is active, which is quite normal. If you apply the brakes while thisfunction is active, the brake pedal will feel stiffer than usual.

This is one of the DSTC system's permanent functions and is not affected when the DSTC button on the center controlpanel is pressed.

The DSTC buttonThe DSTC button in the center control panel is used to switch the Spin Control (SC) function on or off.

The button must be pressed for at least a half second to prevent SC from being switched off inadvertently.

2006 VOLVO XC90


When the system has been switched off, the green indicator lamp in the button will go out and "DSTC SPINCONTROL OFF" will be displayed in the text window.

All DSTC functions are (re)activated each time the engine is started.


Dynamic Stability Traction Control (DSTC) (contd)

The Stability Control indicator light

The Stability Control indicator light will come on for approximately 2 seconds when the ignition is switched on asthe system performs a self-diagnostic test.

The Stability Control indicator light will flash when:

Traction Control is actively functioning to help avoid drive-wheel spin.Spin Control is actively functioning to help avoid loss of traction during acceleration.Active Yaw Control is actively functioning to help avoid skids or lateral slides.Roll Stability Control is actively functioning to help avoid a roll-over situation.

The warning symbol in the instrument panel

A steady yellow glow indicates:

That the system has been automatically disengaged due to a fault. "ANTI SKID SERVICE REQUIRED" will bedisplayed in the text window. If this occurs, stop the vehicle in a suitable place, switch off and restart the engine. If thelight remains on, an authorized Volvo retailer should check the system.

In the event of high brake temperature, "TRACTION CONTROL TEMPORARILY OFF" will be displayed in thetext window.The system will automatically switch on again when the brakes have cooled.


Park assist

A-front (accessory as available), B-rear (option)

Front/rear park assistThe park assist system(s) are designed to assist you when driving into parking spaces, garages, etc. They utilizeultrasound sensors located in the bumpers to measure the distance to a vehicle or other object, or a person who may beclose to the front or rear of the vehicle.

2006 VOLVO XC90


When is park assist active?Front: the system is active from the time the engine is started until the car exceeds a speed of approximately 10 mph(15 km/h).

Rear: when the engine is running and reverse gear is selected.

NOTE:

If the vehicle is equipped with front and rear park assist, both systems will either be activated or deactivatedtogether. They cannot be used separately.

The indicator light in the button (see the illustration on page 27) will light up to indicate that park assist system(s)are activated.

When park assist is actively working:1. The audio system's volume will be reduced.2. An intermittent signal will be audible from the speakers to indicate that you are approaching a person, object,parked vehicle, etc.The signals begin when the distance between the bumper and the object is:Rear: approximately 5 feet (1.5 meters)Front: approximately 2.5 ft (0.8 meters).3. At a distance of approximately 1 foot (30 cm), the signal will become constant.

Deactivating the system(s)1. Press the Park assist button on the center console (see page 27) to temporarily deactivate the system(s).2. The indicator light in the button will go out when the system(s) have been deactivated.3. If the vehicle is equipped with front and rear park assist, both systems will be deactivated by pressing the button.

NOTE: It may be necessary to deactivate one or both of the park assist systems in certain cases.

Rear park assist: towing a trailer, carrying bicycles in a rear-mounted carrier, etc, could trigger the rear park assistsystem's sensors.

Front park assist: it may not be possible to combine auxiliary headlights and front park assist since these lightscould trigger the system's sensors.

Faults in the systemIf a fault should occur in the system, the LED in the button will be switched off and a message will be displayed in thetext window.

Cleaning the sensorsFor the system to function properly, the sensors in the front and/or rear bumpers should be kept clean. They can becleaned with car washing detergent and a sponge.

WARNING!This system is designed to be a supplementary aid when the vehicle is backing up. It is not, however, intended toreplace the driver's attention and judgement.


Towing

2006 VOLVO XC90


Positions for attaching towing eyelets

Emergency towingThe towing eyelet is located in the tool bag, under the floor of the cargo area. This eyelet must be screwed into thepositions provided on the right sides of either the front or rear bumper (see illustrations).

To attach the towing eyelet:A Use a coin to pry open the lower edge of the cover (A).B Screw the towing eyelet (C) in place (B), first by hand and then using the tire iron until it is securely in place.After the vehicle has been towed, the eyelet should be removed and returned to the tool bag. Press the cover back intoposition.

Precautions when the vehicle is in tow

The steering wheel must be unlocked. Turn the ignition key to position I or II.The gear selector must be in position N.Maximum speed: 50 mph (80 km/h). Do not exceed the maximum allowable towing speed.Maximum distance with front wheels on ground: 50 miles (80 km).While the vehicle is being towed, try to keep the tow rope taut at all times.The vehicle should only be towed in forward direction.

CAUTION- Please check with state and local authorities before attempting this type of towing, as vehicles being towed aresubject to regulations regarding maximum towing speed, length and type of towing device, lighting, etc.- If the vehicle's battery is dead, do not attempt to start the vehicle by pushing or pulling it as this will damage thethree-way catalytic converter(s). The engine must be jump started using an auxiliary battery (see page 103).- If the vehicle is being towed on a flat bed truck, the towing eyelets must not be used to secure the vehicle on theflat bed. Consult the tow truck operator.

WARNING!- Remember that the power brakes and power steering will not function when engine is not running. The braking andsteering systems will function but the brake pedal pressure required is 3 - 4 times above normal and greater steeringeffort must be exerted.- The towing eyelets must not be used for pulling the vehicle out of a ditch or for any similar purpose involvingsevere strain. Do not use the towing eyelets to pull the vehicle up onto a flat bed tow truck.


Towing (contd)

2006 VOLVO XC90


Towing vehicles with front wheel drive/All Wheel DriveVolvo recommends the use of flat bed equipment.

If wheel lift equipment must be used, please use extreme caution to help avoid damage to the vehicle. In this case, thevehicle should be towed with the rear wheels on the ground if at all possible.

If it is absolutely necessary to tow the vehicle with the front wheels on the ground, please refer to the towinginformation on the previous page.

CAUTIONSling-type equipment applied at the front will damage radiator and air conditioning lines.It is equally important not to use sling-type equipment at the rear or apply lifting equipment inside the rear wheels;serious damage to the rear axle may result.If the vehicle is being towed on a flat bed truck, the towing eyelets must not be used to secure the vehicle on the flatbed. Consult the tow truck operator.

WARNING!Do not use the towing eyelets to pull the vehicle up onto a flat bed tow truck.


Jump starting

Jump startingFollow these instructions to jump start your vehicle's dead battery or to jump start another vehicle's dead battery usingyour vehicle.Although your vehicle's battery is located under the floor of the cargo area, jumper cables should be connected in theengine compartment, to the points shown in the illustrations.

If the 12-volt auxiliary battery to be used is in another vehicle, check that the vehicles are not touching to preventpremature completion of a circuit. Be sure to follow jump starting instructions provided for the other vehicle.

2006 VOLVO XC90


To jump start your vehicle:

Switch off the ignition.First connect the auxiliary battery positive (+) terminal (1) to the positive (+) terminal in your vehicle's engine

compartment (2), located under a small black plastic cover attached to the fuse box cover, marked with a "+" sign.Remove the cover on the main fuse box if necessary to access this terminal. Then connect the auxiliary battery'snegative (- ) terminal (3) to the ground point in your vehicle's engine compartment (4).

Start the engine in the assisting vehicle, then start the engine in the vehicle with dead battery.After the engine has started, first remove the negative (-) terminal jumper cable. Then remove the positive (+)

terminal jumper cable.

WARNING!PROPOSITION 65 WARNING!Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the state ofCalifornia to cause cancer and reproductive harm. Wash hands after handling

WARNING!- Do not connect the jumper cable to any part of the fuel system or to any moving parts. Avoid touching hotmanifolds.Never expose the battery to open flame or electric spark.

- Do not smoke near the battery.

- Batteries generate hydrogen gas, which is flammable and explosive.

- Battery fluid contains sulphuric acid. Do not allow battery fluid to contact eyes, skin, fabrics or painted surfaces. Ifcontact occurs, flush the affected area immediately with water. Obtain medical help immediately if eyes are affected.

- Failure to follow the instructions for jump starting can lead to personal injury.


Towing a trailer

The maximum weights recommended by Volvo for trailers with brakes are shown in the table below.

No. of occupants 1 2 3 4 5 6 7

Seating position Front seat Front seat 2nd row ofseats

2nd row ofseats

2nd row ofseats

Optional 3rdrow of seats

Optional 3rd row ofseats

All Wheel Drive 5,000 lbs(2250 kg)

5,000 lbs(2250 kg)

4,500 lbs(2050 kg)

3,700 lbs(1700 kg)

2,900 lbs(1350 kg)

1,800 lbs (800kg)

Trailer towing notrecommended

Max. trailer hitchtongue load

500 lbs(225 kg)

500 lbs(225 kg)

450 lbs(205 kg)

370 lbs(170 kg)

290 lbs(135 kg) 180 lbs (80 kg) -

Front WheelDrive

4,000 lbs(1800 kg)

4,000 lbs(1800 kg)

4,000 lbs(1800 kg)

4,000 lbs(1800 kg)

3,700 lbs(1650 kg)

2,500 lbs(1150 kg) 1,400 lbs (650 kg)

Max. trailer hitchtongue load

400 lbs(180 kg)

400 lbs(180 kg)

400 lbs(180 kg)

400 lbs(180 kg)

370 lbs(165 kg)

250 lbs (115kg) 140 lbs (65 kg)

2006 VOLVO XC90


NOTE:

Recommended hitch tongue load: not more than 10% of the trailer's weight.The trailer load should be positioned so that it does not shift and the tongue load should be 10% of the trailer's weight.However, the tongue load should not exceed the maximum permissible weights indicated in the table above.

When towing trailers without brakes, the maximum permissible trailer weight is 1,700 lbs (750 kg). If necessary, redistribute the weight of any cargo in the trailer to avoid excessive weight on the trailer hitch. The maximum trailer weight listed in the table for All Wheel Drive models, 5,000 lbs (2250 kg) is only applicable

when there are not more than two occupants in the vehicle, in the front seats, with a combined weight of 300 lbs (135kg), with no other cargo in the vehicle.


Towing a trailer (contd)

The maximum weight listed for Front Wheel Drive models, 4,000 lbs (1800 kg) is only applicable when there arenot more than four occupants in the vehicle, in the front seats and second row of seats, with a combined weight of 600lbs (270 kg), with no other cargo in the vehicle.

Please be aware that the load on the trailer hitch is part of the vehicle's total load carrying capacity. The amount ofcargo in the vehicle and the trailer must be limited so that the gross vehicle weight and maximum permissible rear axleweight (see page 173) are not exceeded.

Vehicles used for towing a trailer on a regular basis, or for long-distance highway towing should be equipped withan automatic transmission oil cooler and Volvo's automatic self-leveling system for the rear suspension. Consult yourVolvo retailer.

Volvo recommends the use of Volvo trailer hitches that are specially designed for the vehicle. All Volvo models are equipped with energy-absorbing shock-mounted bumpers. Trailer hitch installation should not

interfere with the proper operation of this bumper system. Increase tire pressure to recommended full inflation pressure. See chapter "Wheels and tires." When your vehicle is new, avoid towing heavy trailers during the first 620 miles (1,000 km). Engine and transmission are subject to increased loads. Therefore, engine coolant temperature should be closely

watched when driving in hot climates or hilly terrain. Use a lower gear and turn off the air conditioner if thetemperature gauge needle enters the red range.

If the automatic transmission begins to overheat, a message will be displayed in the text window. Hauling a trailer affects handling, durability, and economy. It is necessary to balance trailer brakes with the towing vehicle brakes to provide a safe stop (check and observe

state/local regulations). Do not connect the trailer's brake system directly to the vehicle's brake system. Remove the ball and drawbar assembly when the hitch is not being used. Volvo recommends the use of synthetic engine oil when towing a trailer over long distances or in mountainous

areas.

WARNING!- Bumper-attached trailer hitches must not be used on Volvos, nor should safety chains be attached to the bumper.Trailer hitches attaching to the vehicle rear axle must not be used.- Never connect a trailer's hydraulic brake system directly to the vehicle brake system, nor a trailer's lighting systemdirectly to the vehicle lighting system. Consult your nearest authorized Volvo retailer for correct installation.- When towing a trailer, the trailer's safety wire must be correctly fastened to the hole or hook provided in the trailerhitch on the vehicle. The safety wire should never be fastened to or wound around the drawbar ball.

NOTE!- When parking the vehicle with a trailer on a hill, apply the parking brake before putting the gear selector in (P)ark.

2006 VOLVO XC90


When starting on a hill, put the gear selector in (D)rive before releasing the parking brake. Always follow the trailermanufacturer's recommendations for wheel chocking.- If you use the manual (Geartronic) shift positions while towing a trailer, make sure the gear you select does not puttoo much strain on the engine (using too high a gear).


Smoother starts with a trailer Models equipped with the V8-engine and the 6-speed automatic transmission have abuilt-in function that reduces acceleration slightly in first gear when the vehicle is towing a trailer. This is done to helpavoid wheel spin and to make starting off smoother.

This function is activated when the trailer's electrical connector is plugged into the electrical socket mounted near thetrailer hitch.

The function is automatically deactivated when the trailer's wiring is disconnected from the socket. The vehicle willthen accelerate normally.

NOTE: Since this function is activated when a connector is plugged into the electrical socket near the trailer hitch, itwill be activated by any electrical equipment (e.g. bicycle racks with lighting, etc) that is plugged in, and will remainactive until the equipment is unplugged from the socket.

LevelingIf your vehicle is equipped with automatic levelling, the rear suspension always retains the correct ride heightregardless of the load.

The system adjusts the rear suspension to the correct level after the vehicle has been driven a short distance. When the vehicle is stationary, the rear suspension lowers, which is normal.

A - ball holder, B - locking bolt, C - safety wireattachment, D - hitch assembly, E - cotter pin

Detachable trailer hitch - installing/removing

Installing the ball holder1. If necessary, remove the cotter pin from the locking bolt and slide the locking bolt out of the hitch assembly.2. Slide the ball holder into the hitch assembly.3. Align the hole in the ball holder with the one in the hitch assembly.4. Slide the locking bolt through the hitch assembly/ball holder.5. Insert the cotter pin in the hole at the end of the locking bolt.

Removing the ball holder1. Remove the cotter pin from the locking bolt and slide the locking bolt out of the ball holder/hitch assembly.

2006 VOLVO XC90


2. Pull the ball holder out of the hitch assembly.

NOTE: A cover for the hitch assembly can be purchased from your Volvo retailer.


Load carriers

Positioning the load carriersMake sure that the wing-shaped load carriers are installed on the roof rails with the rounded edge forward (see theinset illustration above). The load carriers are identical and can be placed anywhere along the roof rails.

When not in use, we recommend that the front load carrier be placed approximately 2 inches (5 cm) in front of thecenter roof rail anchorage point and the rear load carrier approximately 1.5 inches (3.5 cm) in front of the rear railanchorage. This will help to reduce wind noise.

NOTE: Volvo accessories mounted on these load carriers will require T-track mounting hardware for correctinstallation. Please consult your Volvo retailer.

Installing the load carriersMake sure that the load carrier is pressed firmly out against the roof rail. Screw the load carrier in place. Use thesupplied torque wrench and tighten to the mark on the wrench (corresponding to 6 Nm). See illustration.

WARNING!Loads carried on the vehicle's roof should not exceed 220 lbs (100 kg), including the weight of the load carriers andany other load carrying equipment (ski boxes, bicycle racks, etc.). Excessive loads on the roof can adversely affectthe handling and roadholding characteristics of the vehicle.

2006 VOLVO XC90


Load carrier coverThe vehicle's ignition key or the stud on the edge of the supplied torque wrench can be used to undo or tighten thecover. Turn a quarter turn (90 degrees). See illustration.


Cold weather precautions

If you wish to check your vehicle before the approach of cold weather, the following advice is worth noting:

Make sure that the engine coolant contains 50 percent antifreeze. Any other mixture will reduce freeze protection.This gives protection against freezing down to -31°F (-35°C). See section "Coolant". The use of "recycled"antifreeze is not approved by Volvo. Different types of antifreeze must not be mixed.

Volvo recommends using only genuine Volvo antifreeze in your vehicle's radiator. Your Volvo retailer stocks plentyof Volvo engine coolant to help protect your vehicle during cold weather.

Try to keep the fuel tank well filled - this prevents the formation of condensation in the tank. In addition, inextremely cold weather conditions it is worthwhile to add fuel line de-icer before refueling.

The viscosity of the engine oil is important. Oil with low viscosity (thinner oil) improves cold-weather starting aswell as decreasing fuel consumption while the engine is warming up. For winter use, 5W-30 oil, particularly thesynthetic type*, is recommended. Be sure to use good quality oil but do not use cold-weather oil for hard driving or inwarm weather. See section "Engine oil" for more information.

The load placed on the battery is greater during the winter since the windshield wipers, lighting, etc. are used moreoften. Moreover, the capacity of the battery decreases as the temperature drops. In very cold weather, a poorly chargedbattery can freeze and be damaged. It is therefore advisable to check the state of charge more frequently and spray anantirust oil on the battery posts.

Volvo recommends the use of snow tires on all four wheels for winter driving - see section "Wheels and tires."To prevent the washer fluid reservoir from freezing, add washer solvents containing antifreeze (see page 147 for

the location of the washer fluid reservoir).This is important since dirt is often splashed on the windshield during winter driving, requiring the frequent use of thewashers and wipers. Volvo Washer Solvent should be diluted as follows:Down to 14° F (-10° C): 1 part washer solvent and 4 parts waterDown to 5° F (-15° C): 1 part washer solvent and 3 parts waterDown to 0° F (-18° C): 1 part washer solvent and 2 parts waterDown to -18° F (-28° C): 1 part washer solvent and 1 part water

Use Volvo Teflon Lock Spray in the locks.

NOTE: Avoid the use of de-icing sprays as they can cause damage to the locks.

W Winter/Wet driving mode-enhanced vehicle traction

Mode W will only function if the gear selector is in the (D)rive position.Press the button at the base of the gear selector to engage/disengage this driving mode.

2006 VOLVO XC90


An LED in the button will light up to indicate that W is engaged and this will also be displayed in the instrumentpanel (see page 22).

This mode may be selected for starting/moving off on slippery roads.

* Synthetic oil is not used when the oil is changed at the normal maintenance intervals except at owner request and at additional charge. Pleaseconsult your Volvo retailer.


Before a long distance trip

It is always worthwhile to have your vehicle checked at a Volvo retailer before driving long distances. Your retailerwill also be able to supply you with bulbs, fuses, spark plugs and wiper blades for your use in the event that problemsoccur.

As a minimum, the following items should be checked before any long trip:

Check that engine runs smoothly and that fuel consumption is normal.Check for fuel, oil, and fluid leakageCheck transmission oil level*.Check condition of drive belts.Check state of the battery's charge.Examine tires carefully (the spare tire as well), and replace those that are worn. Check tire pressures.The brakes, front wheel alignment, and steering gear should be checked by your Volvo retailer only.Check all lights, including high beams.Reflective warning triangles are legally required in some states/provinces.Have a word with your Volvo retailer if you intend to drive in countries where it may be difficult to obtain the

correct fuel.Consider your destination. If you will be driving through an area where snow or ice are likely to occur, consider

snow tires.

* To prevent injury from contact with hot surfaces, do not inspect your vehicle's transmission fluid yourself. Have yourvehicle's transmission fluid level inspected by a qualified Volvo service technician.



2006 VOLVO XC90


pg. 13 Safety

Volvo Inflatable Curtain (VIC)

7-seat model shown

Volvo Inflatable Curtain (VIC)This system consists of Inflatable Curtains located along the sides of the roof liners, stretching from the front sidewindows to the rear edge of the rear side windows. It is designed to help protect the heads of the occupants of the frontseats and the occupants of the outboard rear seating positions, including the outboard passenger in the optional thirdrow of seats in certain side impact collisions.

The Inflatable Curtains in the Volvo XC90 are also designed to help protect the occupants of the vehicle in a roll-oversituation, and to help prevent them from being thrown from the vehicle if a roll-over occurs.

NOTE: In 5-seat models, the Inflatable Curtains extend to protect both rows of seats. In 7-seat models, they extend toprotect all three rows.

By design, the IC system deploys only on the side of the vehicle affected by the impact.

However, in certain side impacts, or in a rollover situation, BOTH the Inflatable Curtains (IC) and the Side ImpactAirbag System (SIPS-bag) will deploy, whereas, in some cases, ONLY the Inflatable Curtain (IC) will deploy. Incases where BOTH the IC and the SIPS-bag deploy, deployment will occur simultaneously.

NOTE: If the Inflatable Curtain deploys, it remains inflated for approximately 5 seconds.

WARNING!

The VIC system is a supplement to the Side Impact Protection System. It is not designed to deploy duringcollisions from the front or rear of the car or in rollover situations.

Never try to open or repair any components of the VIC system. This should be done only by a trained andqualified Volvo service technician.

In order for the VIC to provide its best protection, both front seat occupants and both outboard rear seat occupantsshould sit in an upright position with the seat belt properly fastened; adults using the seat belt and children using theproper child restraint system. Only adults should sit in the front seats. Children must never be allowed in the frontpassenger seat. See page 19 for guidelines. Failure to follow these instructions can result in injury to the vehicleoccupants in an accident.

2006 VOLVO XC90


pg. 14 Safety

Inspecting SRS system components

Inspection date 1. Driver's side airbag 2. Passenger's side airbag 3. Side airbag on the driver's side4. Side airbag on the passenger's side5. Driver's side inflatable curtain 6. Passenger's side inflatable curtain

WARNING!There is no owner maintenance that can be performed on the SRS system. The month and year shown on the decal tothe right (located on door pillar) indicate when you should contact your Volvo retailer for specific servicing orreplacement of SRS system components. This service must be performed by a trained and qualified Volvo servicetechnician.

This is a sample of the decal located in the left rear door opening

pg. 15 Safety

Whiplash Protection System (WHIPS)

2006 VOLVO XC90


Whiplash Protection System (WHIPS) - front seats onlyThe WHIPS system consists of specially designed hinges and brackets on the front seat backrests designed to helpabsorb some of the energy generated in a collision from the rear (when the vehicle is "rear-ended").

In the event of a collision of this type, the hinges and brackets of the front seat backrests are designed to changeposition slightly to allow the backrest/head restraint to help support the occupant's head before moving slightlyrearward. This movement helps absorb some of the forces that could result in whiplash.

WARNING!

The WHIPS system is designed to supplement the other safety systems in your car. For this system to functionproperly, the three-point seat belt must be worn. Please be aware that no system can prevent all possible injuries thatmay occur in an accident.

The WHIPS system is designed to function in certain collisions from the rear, depending on the crash severity,angle and speed.

Occupants in the front seats must never sit out of position. The occupant's back must be as upright as comfortallows and be against the seat back with the seat belt properly fastened.


pg. 16 Safety

WARNING!

Boxes, suitcases, etc. wedged behind the front seats could impede the function of the WHIPS system.

2006 VOLVO XC90


If the rear seat backrests are folded down, cargo must be secured to prevent it from sliding forward against thefront seat backrests in the event of a collision from the rear. This could interfere with the action of the WHIPSsystem.

If your car has been involved in a rear-end collision, the front seat backrests must be inspected by a trained andqualified Volvo service technician, even if the seats appear to be undamaged. Certain components in the WHIPSsystem may need to be replaced.

Do not attempt to service any component in the WHIPS system yourself.Any contact between the front seat backrests and the folded rear seat could impede the function of the WHIPS

system. If the rear seat is folded down, the occupied front seats must be adjusted forward so that they do not touchthe folded rear seat.

pg. 17 Safety

Child safety

Children should be seated safelyVolvo recommends the proper use of restraint systems for all occupants including children. Remember that, regardlessof age and size, a child should always be properly restrained in a car.

Your car is also equipped with ISOFIX/ LATCH attachments, which make it more convenient to install child seats.

Some restraint systems for children are designed to be secured in the vehicle by lap belts or the lap portion of a lap-shoulder belt. Such child restraint systems can help protect children in cars in the event of an accident only if they areused properly. However, children could be endangered in a crash if the child restraints are not properly secured in thevehicle. Failure to follow the installation instructions for your child restraint can result in your child striking thevehicle's interior in a sudden stop.

Holding a child in your arms is NOT a suitable substitute for a child restraint system. In an accident, a child held in aperson's arms can be crushed between the vehicle's interior and an unrestrained person. The child could also be injuredby striking the interior, or by being ejected from the vehicle during a sudden maneuver or impact. The same can alsohappen if the infant or child rides unrestrained on the seat. Other occupants should also be properly restrained to helpreduce the chance of injuring or increasing the injury of a child.

All states and provinces have legislation governing how and where children should be carried in a car. Find out theregulations existing in your state or province. Recent accident statistics have shown that children are safer in rearseating positions than front seating positions when properly restrained. A child restraint system can help protect a childin a vehicle. Here's what to look for when selecting a child restraint system:

It should have a label certifying that it meets applicable Federal Motor Vehicle Safety Standards (FMVSS 213) - orin Canada, CMVSS 213.

Make sure the child restraint system is approved for the child's height, weight and development - the label requiredby the standard or regulation, or instructions for infant restraints, typically provide this information.

In using any child restraint system, we urge you to carefully look over the instructions that are provided with therestraint. Be sure you understand them and can use the device properly and safely in this vehicle. A misused childrestraint system can result in increased injuries for both the infant or child and other occupants in the vehicle.

When a child has outgrown the child safety seat, you should use the rear seat with the standard seat belt fastened. Thebest way to help protect the child here is to place the child on a cushion so that the seat belt is properly located on thehips (see the illustration on page 18). Legislation in your state or province may mandate the use of a child seat orcushion in combination with the seat belt, depending on the child's age and/or size. Please check local regulations.

A specially designed and tested booster cushion (not available in Canada) can be obtained from your Volvo retailer forchildren weighing 33 - 80 lb. (15 - 36 kg) and 38-54 inches (97 - 137 cm) in height.

2006 VOLVO XC90


WARNING!

Do not use child safety seats or child booster cushions/backrests in the front passenger's seat. We also recommendthat children under 4 feet 7 inches (140 cm) in height who have outgrown these devices sit in the rear seat with theseat belt fastened.

On hot days, the temperature in the vehicle interior can rise very quickly. Exposure to these high temperatures foreven a short period of time can cause heat-related injury or death. Small children are particularly at risk.

pg. 18 Safety

Child safety (contd)

Integrated child booster cushion (option)Volvo's own integrated booster cushion has been specially designed to help safeguard a child seated in the rear seat.When using an integrated booster cushion, the child must be secured with the vehicle's three-point seat belt.

Use this booster cushion only with children who weigh between 33 and 80 lbs (15 and 36 kg) and whose height isbetween 38 and 54 in (97 and 137 cm).

The child should be properly seated on the booster cushion. The hip section of the three-point seat belt must fit snuglyacross the child's hips, not across the stomach. The shoulder section of the three-point seat belt should be positionedacross the chest and shoulder (see illustration). The shoulder belt must never be placed behind the child's back or underthe arm.

WARNING!

DEATH or SERIOUS INJURY can occurFollow all instructions on the booster cushion and in the vehicle's owner's manual.MAKE SURE THE BOOSTER CUSHION IS SECURELY LOCKED BEFORE THE CHILD IS SEATED.Use this booster cushion only with children who weigh between 33 and 80 lbs (15 and 36 kg) and whose height is

between 38 and 54 in (97 and 137 cm).In the event of a collision while the integrated booster cushion was occupied, the entire booster cushion and seat

belt must be replaced. The booster cushion should also be replaced if it is badly worn or damaged in any way. Thiswork should be performed by an authorized Volvo retailer only.

Canada only: This cushion may be referred to as a built-in booster cushion.

2006 VOLVO XC90


Raising

Pull the handle at the front of the cushion (1) forward.Move the seat belt latch aside before raising the cushion.With both hands push the cushion rearward (2).Push the cushion until it locks in place.

Lowering

Pull the handle at the front of the cushion (1) forward.Pull the seat forward and press it down until it locks in place.

The booster cushion must be pressed down before the backrest can be folded down.

pg. 19 Safety

Automatic Locking Retractor/ Emergency Locking Retractor To make child seat installation easier, each seat belt (except for the driver's belt) is equipped with a locking mechanismto help keep the seat belt taut.

When attaching the seat belt to a child seat:

Attach the seat belt to the child seat according to the child seat manufacturer's instructions.Pull the seat belt out as far as possible.Insert the seat belt latch plate into the buckle (lock) in the usual way.Release the seat belt and pull it taut around the child seat.

A sound from the seat belt retractor will be audible at this time and is normal.

The belt will now be locked in place.

This function is automatically disabled when the seat belt is unlocked and the belt is fully retracted.

WARNING!Do not use child safety seats or child booster cushions/backrests in the front passenger's seat. We also recommendthat children who have outgrown these devices sit in the rear seat with the seat belt properly fastened.

Volvo's recommendations Why does Volvo believe that no child should sit in the front seat of a car? It's quite simple really. A front airbag is avery powerful device designed, by law, to help protect an adult. Because of the size of the airbag and its speed ofinflation, a child should never be placed in the front seat, even if he or she is properly belted or strapped into a child

2006 VOLVO XC90


safety seat. Volvo has been an innovator in safety for over seventy-five years, and we'll continue to do our part. Butwe need your help. Please remember to put your children in the back seat, and buckle them up.

Volvo has some very specific recommendations:

Always wear your seat belt.Airbags are a SUPPLEMENTAL safety device which, when used with a three-point seat belt can help reduce serious

injuries during certain types of accidents. Volvo recommends that you do not disconnect the airbag system in yourvehicle.

Volvo strongly recommends that everyone in the vehicle be properly restrained.Volvo recommends that ALL occupants (adults and children) shorter than 4 feet 7 inches (140 cm) be seated in the

back seat of any vehicle with a front passenger side airbag.

Drive safely!

pg. 20 Safety

Child restraint anchorages Volvo vehicles are equipped with child restraint top tether anchorages in the rear seats (second row of seats in seven-seat models). Refer to the child seat manufacturer's instructions for information on securing the child seat.

WARNING!

Child restraint anchorages are designed to withstand only those loads imposed by correctly fitted child restraints.Under no circumstances are they to be used for adult seat belts or harnesses. The anchorages are not able towithstand excessive forces on them in the event of collision if full harness seat belts or adult seat belts are installedto them. An adult who uses a belt anchored in a child restraint anchorage runs a great risk of suffering severe injuriesshould a collision occur.

Do not install rear speakers that require the removal of the top tether anchors or interfere with the proper use ofthe top tether strap.

Top tether straps should be routed beneath the head restraints.

2006 VOLVO XC90


ISOFIX/LATCH anchors Lower anchors for ISOFIX-equipped child seats are located in the second row outboard seats, hidden below thebackrest cushions. Symbols on the seat back upholstery mark the anchor positions as shown. To access the anchors,kneel on the seat cushion and locate the anchors by feel. Always follow your child seat manufacturer's installationinstructions, and use both ISOFIX lower anchors and top tethers whenever possible.


2006 VOLVO XC90


pg. 198 Audio

Menu settings and selections

Main menus/submenusRADIO 1. AUTOSTORE* 1.1. AST MODE 1.2. AST SEARCH 1.2.1 AUTOSTORING2. SCAN* ON/OFF**3. RADIOTEXT* ON/OFF**4. RADIO SETTINGS 4.1. PTY 4.1.1. SELECT PTY 4.1.2. SEARCH PTY* 4.1.3. SHOWPTY ON/OFF** 4.2. AF* ON**/OFF 4.3. RESET ALL5. AUDIO SETTINGS 5.1. Dolby FM 5.1.1. Pro Logic II 5.1.2. 3CH 5.1.3. OFF** 5.2. Dolby CD 5.2.1. Pro Logic II** 5.2.2. 3CH 5.2.3. OFF 5.3. SUBWOOFER* ON/OFF** (certain audio systems) 5.4. EQ FRONT (certain audio systems) 5.5. EQ REAR (option) 5.6. RESET ALL

CD (single disc)1. RANDOM*2. SCAN*3. AUDIO SETTINGS* 3.1. Dolby FM 3.1.1. Pro Logic II 3.1.2. 3CH 3.1.3. OFF** 3.2. Dolby CD 3.2.1. Pro Logic II** 3.2.2. 3 CH 3.2.3. OFF ON/**OFF 3.3. SUBWOOFER* ON/OFF** (option) 3.4. EQ FRONT (certain audio systems) 3.5. EQ REAR (certain audio systems) 3.6. RESET ALL

CDX (CD changer - option)1. RANDOM*

2006 VOLVO XC90


1.1. OFF 1.2. SINGLE DISC 1.3. ALL DISCS2. SCAN*3. DISC TEXT4. AUDIO SETTINGS* 4.1. Dolby FM 4.1.1. Pro Logic II 4.1.2. 3CH 4.1.3. OFF** 4.2. Dolby CD 4.2.1. Pro Logic II** 4.2.2. 3 CH 4.2.3. OFF ON/**OFF 4.3. SUBWOOFER* ON**/OFF (option) 4.4. EQ FRONT (certain audio systems) 4.5. EQ REAR (certain audio systems) 4.6. RESET ALL

* These functions can be programmed with MY KEY (see page 193).

** Default

pg. 199 Audio

CD player

Starting the CD1. Select the CD mode using the SELECTOR control (1) or the CD button (2).2. Insert a CD into the player.

CD PauseTo pause CD playback, turn the volume all the way down. "CD paused" will be displayed. This will not occur ifsomeone in the rear seat is listening to the CD through the optional headphones.Play will resume when the volume is turned up again.

Changing tracksPress to go to the next track or to go to the previous track. The track number is shown in the display. If you

have a keypad in the steering wheel, you can use the arrow keys in the same way.

2006 VOLVO XC90


Searching within a trackPress and hold down or to search within a track or the whole disc. The search continues as long as the

buttons are depressed. If you have a keypad in the steering wheel, you can use the arrow keys in the same way.

Random playThis function plays the tracks on a CD in random order (shuffle).

1. Press the MENU button.2. Select RANDOM and press ENTER.3. RND is shown in the display as long as the function is activated.4. Go into the menu and select RANDOM OFF to stop random play, or press EXIT.

pg. 200 Audio

CD player (contd)

SCAN This function plays the first ten seconds of each track.

1. Press the MENU button.2. Select SCAN and press ENTER.3. Press EXIT/CLEAR to listen to an entire track.

DisctextCertain CDs contain information about the disc, such as the titles of the tracks, etc. This information can be shown inthe display by activating the DISCTEXT function.

1. Press the MENU button.2. Select DISCTEXT in the menu and press ENTER.3. Any information that may be stored on the disc will be displayed.4. To deactivate this function, select DISCTEXT and press ENTER.

NOTE: This function is only available on the CD changer.

CD ejectPress button 1 to eject the CD.

NOTE: For reasons of traffic safety, the ejected CD must be removed within 12 seconds or it will be automaticallydrawn back into the slot and the CD player will enter pause mode. Press the CD button to restart the disc.

2006 VOLVO XC90


pg. 201 Audio

CD changer (option)

CD changer (option)The CD changer can hold up to six discs.

1. Choose CD mode using the SELECTOR control or the CD button.2. Select an empty slot with the number keys 1-6 (1). The display indicates which slots are empty.3. Insert a disc into the changer.

To insert a new disc, you must first select an available empty slot in the CD changer. Make sure INSERT DISC isdisplayed before inserting a new disc.

Selecting disc numberUse the station setting buttons 1-6 (1) to select which disc is to be played. The number of the disc and the track areshown in the display.

SCANThis function plays the first ten seconds of each track and only functions on the currently selected disc.

1. Press the MENU button.2. Select SCAN and press ENTER.

Press EXIT/CLEAR to listen to an entire track.

Changing tracksPress to go to the next track or to go to the previous track. The track number is shown in the display. If you

have a keypad in the steering wheel, you can use the arrow keys in the same way.

Searching within a trackPress and hold down or to search within a track or the whole disc. The search continues as long as the

buttons are depressed. If you have a keypad in the steering wheel, you can use the arrow keys in the same way.

pg. 202 Audio

CD changer (option) (contd)

2006 VOLVO XC90


Random playThis function offers two alternatives for playing the tracks on the disc(s) in the CD changer in random order (shuffle).

Random one (random order on the currently selected disc) Random all (random order on all of the CD's in the changer)

To play tracks in random order:1. Press the MENU button.2. Select RANDOM and press ENTER.3. Select SINGLE DISCS or ALL DISCS to play tracks randomly from one or all of the discs in the CD changer.4. RND or RND ALL is shown in the display for as long as the function is activated.

NOTE: Press to play the next randomly selected track. This can only be done on the currently selected disc.

5. Press EXIT to stop random play.

Ejecting one discA short press on the EJECT button (1) will eject the CD that is currently playing.

NOTE: For reasons of traffic safety, you have 12 seconds in which to remove the ejected disc. After that, the discautomatically reinserts into the player.

Ejecting all discsA long press on the EJECT button (1) starts the EJECT ALL function.The text EJECTING ALL will be displayed and the entire magazine will be emptied disc by disc.

NOTE: - The EJECT ALL function can only be used while the vehicle is at a standstill and will be cancelled if the vehiclebegins to move.- For reasons of traffic safety, you have 12 seconds in which to remove the ejected disc. After that, the discautomatically reinserts into the player.

pg. 203 Audio

Audio systems - general information

Compact disc care

Before using a new CD for the first time, remove any burrs in the center/outer edge by running the stem of a pen orsimilar object around the hole/edge of the disc.

2006 VOLVO XC90


Use CD standard EN 60908 discs only. Discs not meeting this standard may cause problems with system (poorsound). CDR discs can cause listening problems due to the quality of the disc or recording equipment used.

Keep the discs clean. Wipe them with a soft, clean, lint-free cloth, working from the center outwards. If necessary,dampen the cloth with a neutral soap solution. Dry thoroughly before using.

Never use cleaning spray or antistatic liquid. Use only cleaners specifically made for CD's. Use discs of the correct size only (3.5" discs should never be used). Do not put tape or labels on the disc itself. They could become stuck in the player. Volvo does not recommend the use of plastic outer rings on the disc. Condensation may occur on discs/optical components of the changer in cold winter weather. The disc can be dried

with a clean, lint-free cloth. Optical components in the CD changer may, however, take up to one hour to dry off. Never attempt to play a disc which is damaged in any way. When not in use, the discs should be stored in their covers. Avoid storing discs in excessive heat, direct sunlight or

dusty locations.

pg. 204 Audio

HomeLink® Universal Transceiver

Hand-held transmitter

HomeLink® Universal TransceiverHomeLink® is an advanced system that can be programmed to learn the codes of three different remote controlled-devices (e.g., garage door openers, remote lighting, entry door lock). HomeLink®'s sun visor-mounted transceiver,powered by your vehicle's electrical system, may then be used in place of your hand-held remote controls.

NOTE: For your security, the HomeLink® Universal Transceiver is designed to not function if you lock your vehiclefrom the outside.

Programming the transceiver1. The ignition switch must be turned to the "accessory" position (II) before programming the HomeLink® UniversalTransceiver.

2. Begin by erasing all 3 factory default channels. Hold down the two outside buttons (buttons 1 and 3 in theillustration) on the HomeLink® Universal Transceiver for about 20 seconds, until HomeLink®'s indicator light beginsto flash. Then release the buttons.

3. Hold your hand-held transmitter (garage door opener, for example) 2 to 5 in. (5 to 12 cm) away from theHomeLink® surface, keeping the indicator light in view. For placement questions, contact HomeLink® toll-free 1-800-355-3515 (Internet: www.HomeLink.com).

4. Using two hands, push and hold both your hand-held transmitter's button and the transceiver button you wish to

http://www.homelink.com/

2006 VOLVO XC90


program. The indicator light will flash first slowly, then rapidly. Rapid flashing tells you the HomeLink® button hasbeen successfully programmed. Release both buttons.

5. If you are programming a rolling code-equipped device (e.g., garage door opener or entry door lock), refer to"Programming rolling codes" on the next page to complete the programming process.

Repeat steps 3 and 4 to program the other two transceiver buttons.

If, after several attempts, you are unable to successfully train the HomeLink® Universal Transceiver to learn yourhand-held transmitter's signal, contact HomeLink® toll-free 1-800-355-3515 (Internet: www.HomeLink.com).

pg. 205 Audio

WARNING!- If you use HomeLink® to open a garage door or gate, be sure no one is near the gate or door while it is in motion.- Do not use the HomeLink® Universal Transceiver with any garage door opener that lacks safety "stop" and"reverse" features as required by federal safety standards. (This includes any garage door opener modelmanufactured before April 1, 1982). A garage door opener that cannot "detect" an object, signalling the door to"stop" and "reverse" does not meet current federal safety standards. Using a garage door opener without thesefeatures increases the risk of serious injury or death. For more information on this matter, call toll-free 1-800-355-3515 (Internet: www.HomeLink.com).

NOTE: Canadian residents: During programming, your hand-held transmitter may automatically stop transmitting. To successfully trainHomeLink®, continue to hold the HomeLink® button. At the same time, repeatedly press and hold your hand-heldtransmitter's button at two-second intervals until HomeLink® has learned your transmitter's code. The HomeLink®indicator light will flash first slowly, and then rapidly to indicate that the button has been successfully programmed.

Determining if your garage door uses a rolling codeDetermine, in one of the following ways, if your garage door uses a rolling code system and is manufactured after1996:

Refer to the garage door opener owner's manual for verification. If your hand-held transmitter appears to program the HomeLink® Universal Transceiver but the programmed button

does not activate the garage door, your garage door opener may have a rolling code. Press the programmed HomeLink® button. If the garage door opener has the rolling code feature, the HomeLink®

indicator light flashes rapidly and then glows steadily after approximately 2 seconds.

To train a rolling code garage door opener, follow these instructions after programming the desired transceiver button according to "Programming the transceiver."The help of a second person may make training easier.

1. Locate the training button on the garage door opener motor head unit. The location and color of the training buttonmay vary. If you encounter difficulty, refer to the garage door opener owner's manual or call toll-free 1-800-355-3515(Internet: www.HomeLink.com).2. Press the "training" button on the garage door opener motor head unit until the "training" light comes on.3. Press and release the programmed HomeLink® button. Press and release the programmed HomeLink® button asecond time to complete the training process.4. Some garage door openers may require you to do this procedure a third time to complete the training.5. The programmed button on your HomeLink® Universal Transceiver should now operate your garage door opener.The original hand-held transmitter can also be used, as desired, to operate the garage door.The remaining two HomeLink® buttons can be programmed in the same way. In the event of any problems inprogramming the HomeLink® Universal Transceiver, call toll-free 1-800-355-3515 (Internet: www.HomeLink.com).





2006 VOLVO XC90


Operating the HomeLink® Universal TransceiverOnce programmed, the HomeLink® Universal Transceiver can be used in place of your handheld transmitters.

To operate, the key must be turned to the "accessory" position (II) or the engine must be running. Press theprogrammed HomeLink® button to activate the garage door, driveway gate, security lighting, home security system,etc.

pg. 206 Audio

Your original hand-held transmitters may, of course, be used at any time.

Erasing programmed buttonsIndividual buttons cannot be erased. To erase all three programmed buttons:1. Turn the ignition key to the "accessory" position (II).2. Hold down the two outside buttons on the HomeLink® Universal Transceiver for about 20 seconds, untilHomeLink®'s indicator light begins to flash.3. Release both buttons.

The HomeLink® buttons can be reprogrammed using the procedures described on the previous page.

Reprogramming a single HomeLink® button1. Press and hold the desired HomeLink® button. Do not release the button until step 3 has been completed.2. When the indicator light begins to flash slowly (after approximately 20 seconds), position your hand-heldtransmitter 2 to 5 in. (5 to 12 cm) away from the HomeLink® surface.3. Press and hold the hand-held transmitter button. The HomeLink® indicator light will flash first slowly, then rapidly.When the indicator light flashes rapidly, release both buttons.The previously programmed device has now been erased and the new device can be activated by pressing theHomeLink® button that has just been programmed. This procedure will not affect any other programmed HomeLink®buttons.

NOTE:

Retain the original transmitter(s) for future programming procedures (e.g., if you purchase a new vehicle). For your own security, erase all programmed buttons on the HomeLink® Universal Transceiver when you sell your

vehicle. Metallic sun protection films should not be used on any windows in a vehicle equipped with HomeLink® Universal

Transceiver. This could interfere with the transceiver's function.


2006 VOLVO XC90


pg. 153 Maintenance

Battery MaintenanceThe battery in your vehicle is located under the floor of the cargo compartment.

Driving habits and conditions, climate, the number of starts, etc. all affect the service life and function of the battery.In order for your battery to perform satisfactorily, keep the following in mind:

Check the fluid level in each cell in the battery every 24 months or every 15,000* miles (24,000 km), whichever issooner. The fluid should be at the level shown in the illustration above (A)**.

Use a screw driver to open the caps and a flashlight to inspect the level. If necessary, add distilled water. The level should never be above the indicator (A**). The fluid level should be checked if the battery has been recharged. After inspection, be sure the cap over each battery cell is securely in place. Check that the battery cables are correctly connected and properly tightened. Route ventilation hose through opening

in floor (see page 151) Never disconnect the battery when the engine is running, for example when changing the battery. The battery should be disconnected from the vehicle when a battery charger is used directly on the battery. However, if the battery is being charged via the connecting points in the engine compartment (see page 103), the

battery must be connected.

* More frequently in warm climates.** The level indicator inside the battery could be designed in various ways. See illustration.

2006 VOLVO XC90


pg. 154 Maintenance

Replacing the battery1. Switch off the ignition.2. Wait at least 5 minutes after switching off the ignition before disconnecting the battery so that all informationin the vehicle's electrical system can be stored in the control modules.3. Remove the retaining bracket and unscrew the cover over the battery. Wait at least 5 minutes after switching off theignition before disconnecting the battery so that all information in the vehicle's electrical system can be stored in thecontrol modules.

2006 VOLVO XC90


4. Disconnect the negative (ground) cable first. Disconnect the positive cable and pull the ventilation hose (see nextpage) from the battery.

5. Lift out the old battery and put a new battery into place.6. Connect the positive cable first.7. Connect the negative (ground) cable.8. Be sure that the ventilation hose (see below) is securely connected to the battery and that the other end of the hose isproperly routed through the ventilation opening in the floor of the battery compartment.9. Reinstall the cover and retaining bracket and screw it securely in place.

Ventilation hose

WARNING!- Never expose the battery to open flame or electric spark.- Do not smoke near the battery.- Battery fluid contains sulfuric acid. Do not allow battery fluid to contact eyes, skin, fabrics or painted surfaces. Ifcontact occurs, flush the affected area immediately with water. Obtain medical help immediately if eyes are affected.

pg. 155 Maintenance

Battery Maintenance (contd)

WARNING!Ventilation hose: The battery generates hydrogen gas, which is flammable and explosive. The battery is fitted witha ventilation hose which vents hydrogen gas out of the battery compartment through a ventilation opening in thebottom of this compartment. If the battery must be replaced, it is essential that the ventilation hose is properly

2006 VOLVO XC90


connected to the battery and that it is routed through the ventilation opening provided (see illustration).Be sure the ventilation hose is free of debris. Only use replacement batteries equipped with a ventilation hose.Consult your Volvo retailer.

NOTE: After the battery has been disconnected or replaced, lock and unlock the vehicle with the central lockingsystem's remote control to reactivate such features as the power windows, moonroof, courtesy lighting, etc.

WARNING!PROPOSITION 65 WARNING!Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the state ofCalifornia to cause cancer and reproductive harm. Wash hands after handling.

pg. 156 Maintenance

Bulbs

The following bulbs are used in the vehicle:Bulb Type Socket1. High beam H7 65W -1. Low beam H11 55W -2. Bi-Xenon headlight (option) D2R 35W3. Front fog lights H1 55W4. Front parking lights, front/rear side marker lights, license plate light, rear footwell lighting W5W W2,1x9,5d5. Front turn signals H21W BAY9s5. Rear fog light P21/4W BAY9s6. Side turn signals WY5W W2,1x9,5d7. Brake lights, backup lights P21W BAY15d8. Rear turn signals PY21W BA15s9. Rear parking lights P21/4W BAZ15s10. Vanity mirror lighting 1.2W SV5.511. Front footwell lighting, cargo area lighting C5W SV8.5

WARNING!Bi-Xenon headlights (option) - due to the high voltage used by these headlights, these bulbs should only be replaced

2006 VOLVO XC90


by an authorized Volvo service technician.

pg. 157 Maintenance

Retaining pins

Replacing high/low beams/turn signal/parking light bulbsThe entire lamp housing must be lifted out when replacing these bulbs.

To lift out the lamp housing:1. Switch off the ignition.2. Open the hood.3. Pull up the retaining pins (see the illustration above).4. Lift out the lamp housing.

CAUTION- Do not touch the glass on the halogen bulbs with your fingers. Grease, oil, or any other impurities can becarbonized onto the bulb and cause damage to the reflector. - Be sure to use bulbs of the correct type and voltage.

2006 VOLVO XC90


Location of the bulbs in the headlight housing1. Low beam headlight/Bi-Xenon headlight (option)2. High beam headlight3. Turn signal4. Parking light5. Side marker light

pg. 158 Maintenance

Replacing the low beam bulb1. Remove the plastic cover over the bulb (1) by turning it counterclockwise.2. Pull the connector from the lamp housing (2).3. Loosen the bulb's retaining spring by first moving it to the right and then moving it out of the way.4. Pull out the bulb from the holder.5. Insert the new bulb (without touching the glass) in the holder.6. Move the retaining spring up and push it slightly to the left until it seats properly.7. Press the bulb holder into place on the headlight housing.8. Reinstall the plastic cap. The letters "HAUT" on the cap must be upward.

2006 VOLVO XC90


Replacing the high beam bulb1. Remove the rubber cover over the bulb (1) by pulling it off.2. Pull the connector from the lamp housing (2).3. Loosen the bulb's retaining spring by first moving it to the right and then moving it out of the way.4. Pull out the bulb from the holder.5. Insert the new bulb (without touching the glass) in the holder.6. Move the retaining spring up and push it slightly to the left until it seats properly.7. Press the bulb holder into place on the headlight housing.8. Press the rubber cover into place.

Replacing the parking light/side marker light bulbs1. Turn the lamp holder approximately 1/4 turn counterclockwise and pull it out of the headlight housing.2. Pull the bulb straight out.3. Align the guide lugs on the side of the base of the new bulb in the grooves in the holder and press it into place.4. Press the lamp holder into the place in the headlight housing and turn it approximately 1/4 turn clockwise.

pg. 159 Maintenance

Bulbs (contd)

2006 VOLVO XC90


Replacing the turn signal bulb1. Turn the lamp holder approximately 1/4 turn counterclockwise and pull it out of the headlight housing.2. Press in the bulb slightly and pull it out of the holder.3. Align the guide lugs on the side of the base of the new bulb in the grooves in the holder. Press it in and turn itslightly clockwise.4. Press the lamp holder into the place in the headlight housing and turn it approximately 1/4 turn clockwise.

Replacing the side turn signal bulb1. Switch off the ignition.2. Pry out the lens by inserting a small screw driver under the lower edge.3. Turn the lamp holder 1/4 turn counterclockwise and pull it straight out.4. Pull the bulb straight out of the holder.5. Press the new bulb into the holder.6. Reinsert the bulb holder in the lens and turn 1/4 turn clockwise.

Front fog lights

2006 VOLVO XC90


Avoid touching the glass on the bulb with your fingers.1. Switch off the ignition.2. Turn the bulb holder slightly counterclockwise to release it.3. Replace the bulb. The shape of the foot of the bulb corresponds to the shape of the bulb holder.4. Reinstall the bulb holder by turning it slightly clockwise. The side of the holder marked "TOP" should face upward.

pg. 160 Maintenance

Location of tail light bulbs

A - Turn signal B - Brake light C - Back-up light D - Parking light

Replacing bulbs in the tail light cluster1. Switch off all lights and turn ignition key to position 0.2. Fold down the lower section of the tailgate, and fold up the rear section of the cargo area floor.

3. If the vehicle is equipped with the optional grocery bag holder, detach the holder's bands.4. Remove the corner panel (1 in the illustration above).5. Open the cover (2) in the side panel by pulling the tab (3) upward/outward.6. Loosen the bolts (4) with the 10 mm wrench.7. Pull the entire tail light housing straight out.8. Disconnect the wiring.9. Place the tail light housing on a soft cloth to avoid scratching the lens.10. Turn the lamp holder(s) counterclockwise and pull out.

2006 VOLVO XC90


11. Turn the bulb counterclockwise and remove. Insert a new bulb.12. Place the lamp holder in the groove and turn clockwise.13. Press wiring back into place.14. Align the tail light housing with the holes for the retaining bolts and press it into place.15. Tighten the retaining bolts.16. Reinsert the side and corner panels.

NOTE: If the message indicating a burned out bulb remains in the information display after the bulb has beenreplaced, consult an authorized Volvo retailer or workshop.

pg. 161 Maintenance

Bulbs (contd)

Rear fog light1. Switch off the ignition.2. Carefully insert a small screwdriver (see illustration above)3. Pry out the lamp housing.4. Turn the bulb holder counterclockwise and pull out the bulb.5. Insert a new bulb and press the lamp housing back into place.

Door step courtesy lightsThe door step courtesy lights are located under the dashboard on the driver's and passenger's sides. To replace a bulb:1. Carefully insert a screwdriver and pry out the lens.2. Replace the defective bulb.3. Reinstall the lens.

2006 VOLVO XC90


Cargo compartment light1. Carefully insert a screwdriver and pry out the lens.2. Pry out the bulb and replace it.3. Press the lens back into place.

pg. 162 Maintenance

Front courtesy lightsThese bulbs may be difficult for you to replace yourself. We recommend that you let an authorized Volvo retailerreplace these bulbs if necessary.

Rear reading lightsThese bulbs may be difficult for you to replace yourself. We recommend that you let an authorized Volvo retailer

2006 VOLVO XC90


replace these bulbs if necessary.

NOTE: Other bulbs may be difficult for you to replace yourself. Let an authorized Volvo retailer replace these bulbs ifnecessary.

Vanity mirror lights1. Carefully insert a screwdriver and pry out the lens.2. Pry out the bulb and replace it.3. Carefully press the lower edge of lens onto the four tabs and press the upper edge of the lens into place.

pg. 163 Maintenance

Bulbs (contd)

License plaste lights1. Switch off the ignition.2. Loosen the screws with a Torx screwdriver.3. Turn the bulb holder counterclockwise and pull it out.4. Pull out the defective bulb and insert a new one.5. Reinsert the bulb holder into the housing and turn it clockwise.6. Reinstall the housing and screw it into place.

pg. 164 Maintenance

Fuses

2006 VOLVO XC90


Replacing fusesIf an electrical component fails to function, it is possible that a fuse has blown.

The fuse boxes are located in four different places:1. Relays/fuse box in the engine compartment2. Fuse box in the passenger compartment, behind the plastic cover3. Fuse box in the passenger compartment, on the edge of the dashboard4. Fuse box in the cargo compartment.

A label on the inside of each cover indicates the amperage and the electrical components that are connected to eachfuse.

The easiest way to see if a fuse is blown is to remove it. Pull the fuse straight out. If a fuse is difficult to remove, youwill find a special fuse removal tool (and several extra fuses) in the passenger compartment fuse box on the driver'send of the dashboard. From the side, examine the curved metal wire (see next page) to see if it is broken. If so, put in anew fuse of the same color and amperage (written on the fuse). Spare fuses are stored in the fuse box in the enginecompartment and the passenger compartment. If fuses burn out repeatedly, have the electrical system inspected by anauthorized Volvo retailer.

WARNING!Never use fuses with higher amperage than those stated on the following pages. Doing so could overload thevehicle's electrical system.

pg. 165 Maintenance

Fuses (contd)

A-To open, press the plastice catches on the rear side of the fuse box cover and lift.

Fuse box in the engine compartment

2006 VOLVO XC90


When replacing fuses, be sure to replace a blown fuse with a new one of the same color and amperage (written on thefuse). Fuses in positions marked X are replacement fuses.

Fuses in the engine compartmentNo. Amperage1. ABS 30A2. ABS 30A3. Headlight washers 35A4. -5. Auxiliary lights (option) 20A6. Starter motor relay 35A7. Windshield wipers 25A8. -9. Fuel pump 15A10. Ignition coils, engine control module 20A11. Throttle pedal sensor, A/C compressor, e-box fan 10A12. Engine control module, fuel injectors, mass airflow sensor 15A13. -14. Heated oxygen sensor(s) 20A15. Crankcase ventilation heater, solenoid valves (V8), mass airflow sensor (V8), engine control module(V8) 15A

16. Driver's side low beam headlight 20A17. Passenger's side low beam headlight 20A18. -19. Engine control module feed, engine relay 5A20. Parking lights 15A21. -

pg. 166 Maintenance

Fuses in the passenger compartmentFuses are located inside the access panel on the edge of the dashboard, on the driver's side. There are also a number ofspare fuses. When replacing a blown fuse, be sure to replace it with a new one of the same color and amperage(written on the fuse).

2006 VOLVO XC90


No. Amperage1. Blower - climate system 30A2. Audio amplifier 30A3. Power driver's seat (option) 25A4. Power passenger's seat (option) 25A5. Driver's door - central locking, power windows, door mirror 25A6. Front passenger's door - central locking, power windows, door mirror 25A7. -8. -9. Audio, navigation system (option) 10A10. On-board diagnostics, headlight switch, steering wheel angle sensor, steering wheel module 5A11. Ignition switch, SRS, engine control module, immobilizer, transmission control module (V8) 7.5A12. Ceiling lighting, upper electronic control module 10A13. Moonroof (option) 15A14. -15. -16. -17. -18. -19. -20. -21. -22. -23. -24. -25. -26. -27. -28. -29. -30. -31. -32. -33. -34. -35. -36. -37. -38.-

pg. 167 Maintenance

Fuses (contd)

2006 VOLVO XC90


No. Amperage1. Heated passenger's seat 15A2. Heated driver's seat 15A3. Horn 15A4. -5. Audio system 10A6. -7. -8. Alarm siren 5A9. Brake light switch feed 5A10. Instrument panel, climate system, power driver's seat, Occupant Weight Sensor (USA) 10A11. 12-volt sockets - front and rear seats 15A12. -13. -14. -15. ABS, STC/DSTC 5A16. Power steering, Bi-Xenon headlights (option) 10A17. Driver's side front fog light (option) 7.5A18. Passenger's side front fog light (option) 7.5A19. -20. Coolant pump (V8) 5A21. Transmission control module 10A22. Driver's side high beam 10A23. Passenger's side high beam 10A24. -25. -26. -27. -28. Power passenger's seat (option) 5A29. -30. -31. -32. -33. Vacuum pump 20A34. Pump - windshield and tailgate washers 15A35. -36. -

2006 VOLVO XC90


pg. 168 Maintenance

Fuses (contd)

Fuses in the cargo compartmentThe fuses in the cargo area are located behind the panel on the driver's side of the cargo compartment. When replacinga blown fuse, be sure to replace it with a new one of the same color and amperage (written on the fuse).

Fuses in the cargo compartmentNo. Amperage1. Backup lights 10A2. Parking lights, foglights, cargo compartment lighting, license plate lights, brake light diodes 20A3. Accessories 15A4. -5. Rear electronic module 10A6. Navigation system (option), radio receiver, rear seat entertainment (accessory) 7.5A7. Trailer wiring (30-feed) 15A8. 12-volt socket in cargo compartment 15A9. Rear passenger's side door: power window, power window cutout function 20A10. Rear driver's side door: power window, power window cutout function 20A11. -12. -13. -14. Subwoofer (option), rear air conditioning system (option) 15A15. -16. -17. Accessory audio 5A18. -19. Rear window wiper 15A20. Trailer wiring (15-feed) 20A

2006 VOLVO XC90


21. -22. -23. All Wheel Drive 7.5A24. -25. -26. Park assist 5A27. Main fuse: trailer wiring, park assist, All Wheel Drive 30A28. Central locking system 15A29. Driver's side trailer lighting: parking light, turn signal 25A30. Passenger's side trailer lighting: brake light, fog light, turn signal 25A31. Main fuse: fuses 37, 38 40A32. -33. -34. -

pg. 169 Maintenance

Fuses (contd)

35. -36. -37. Heated rear window 20A38. Heated rear window 20A


2006 volvo xc90 (1)

Documents

american petroleum

conserve washer

minimum octane

mild soap

tow truck

homelink universal

call roadside

outer air