2007 Ducati 1098 - PCIII USB - 1i729-411 www.powercommander.com

2007 Ducati 1098Installation Instructions

Dynojet Research 2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com

Parts List1 Power Commander1 USB Cable1 CD-ROM1 Installation Guide1 Power Adapter1 Wire Tap2 Power Commander Decals2 Dynojet Decals2 Velcro® Strip1 Alcohol Swab4 Zip ties

You can also download the PowerCommander software and latest mapsfrom our web site at:

www.powercommander.com

The ignition MUST be turnedOFF before installation!

PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION

Button Adjustment Display

Faceplate Buttons

Expansion Port USB Port

5. Lay the PCIII in the tail section tem-porarily.

6 Route the PCIII harness through thehole in the tail section (Fig. C).

7. Route the PCIII along the right handside of the subframe . Secure thePCIII harness to the subframe using 2of the large supplied zip ties (Fig. D)

Fig.

BFi

g. A

Fig.

CFi

g. D

2007 Ducati 1098 - PCIII USB - 2i729-411 www.powercommander.com

Zip ties

PCIII harness

1. Remove the seat and solo cover.

2. Remove the cover around the fueltank (Fig. A).

3 Remove the fuel tank

4. Remove the inner fairing cover on theright hand side (Fig. B).

8 Unplug the stock wiring harness fromthe rear injector (Fig. E)

This injector is located on top of theair box.

To remove the connector you mustfirst remove the spring clip. This isbest done with a pick or small screw-driver.

9 Plug the YELLOW colored wiresfrom the PCIII in-line of the stockwiring harness and rear injector(Fig. F).

Make sure to reinstall the spring clipon the stock connector.

10 Use 1 of the small supplied zip ties tosecure this connection to the fuel line.

Make this connection as compact aspossible.

11 Unplug the stock wiring harness fromthe front injector (Fig G).

This connection is very difficult toaccess. It is best to get to thru thefront of the bike directly above theradiator.

Figure G was taken from the front ofthe bike inside the right hand fairingand above the radiator.

Fig.

EFi

g. F

Fig

G

2007 Ducati 1098 - PCIII USB - 3i729-411 www.powercommander.com

Unplug

PCIII connector Stock connector

Zip tie

Stock connector

14 Route the PCIII harness along theright hand side frame down tube. Usethe existing wraps to hold the PCIIIharness in place (Fig. J).

15 Locate the Throttle Position Sensor onthe right hand side of the throttle bod-ies.

16 Crimp the supplied wire tap to theORANGE wire (C position).

17 Connect the GREY wire from thePCIII to the wire tap.

It is recommended to use dielectricgrease on these connections.

12 Plug the ORANGE colored wiresfrom the PCIII in-line of the frontinjector and stock wiring harness(Fig. H).

13 Remove the right hand fairing.Fig.

H

2007 Ducati 1098 - PCIII USB - 4i729-411 www.powercommander.com

PCIII connector Stock connector

Fig.

J

18 Attach the ground wire from the PCIIIto the right hand engine cover boltshown in Figure K

19 Reinstall the right hand fairing

Ground wirefrom PCIII

Fig.

K

TPS

PCIII harness

Grey wire

2007 Ducati 1098 - PCIII USB - 5i729-411 www.powercommander.com

20 Install the PCIII in the tail sectionusing the supplied velcro. Make sureto clean both surfaces with the alcoholswab before attaching.

21 Reinstall all bodywork and fuel tank.

When lowering the fuel tank makesure it does not interfere with the con-nection of the rear injector.

Note: Unless you have the Kit ECU you willnot be able to make fuel changesbelow 20% throttle and below5500rpm with this PCIII.