2011 february product guide smart bias-t · product guide • hybrid combiner p/n : it-125l001...
TRANSCRIPT
2 0 1 1 F E B R U A R Y
• S M A R T B I A S - TPRODUCT GUIDEP/N : IT-127X006
D E S C R I P T I O N S
A bias “T” is used to insert DC power into anAC signal to power remote antenna amplifiersor other devices. It is usually positioned at thereceiving end of the coaxial cable to pass DCpower from an external source to the coaxialcable running to powered device This Bias-T iscable running to powered device. This Bias T isused to DC feeding of devices such as theTower Mounted Amplifier (TMA) RemoteElectrical Tilt (RET) systems. Furthermore, theBias-T has an AISG 2.0 modem integrated thatconverts the 2.176 MHz on/off shift keyingsignal (OOSK) to RS485 communication.
• AISG 2 0 Protocol Compliant
S P E C I F I C A T I O N S
Frequency Range 698 – 2690 MHz
C H A R A C T E R I C S T I C S
• AISG 2.0 Protocol Compliant• Wide Band Usage• Lighting Protected
Return Loss Port 1 & 2 -20 dB Max.
Insertion Loss Port 1 & 2 0.2 dB Max.
Nominal Impedance Port 1 & 2 50 Ohms
Resistance RS485A & RS485B 1 KOhms Min.
Capacitance RS485A & RS485B 1 nF Min.
Time delay 30 ns Max.
IM3, 2x 20W -110 dBm Max.
Power Consumption 2 W Max.
DC Current 1 Amp. Max.
Head Office & Factory - Location : Incheon-City, Korea Tel : +82-32-816-1456 E-mail : [email protected]
Copyright 2010. Innertron, Inc. All rights Reserved
2 0 1 0 M A R C H
• DUAL DIRECTIONAL COUPLER PRODUCT GUIDEP/N : IT-126K001
D E S C R I P T I O N S
A coupler couples part of the transmission
power in a transmission line by a known
amount out through another port, often by
using two transmission lines set close enoughg g
together such that energy passing through one
is coupled to the other.
• Low Intermodulation
• Low Insertion Loss
• 870 – 2170MHz
S P E C I F I C A T I O N S
C H A R A C T E R I C S T I C S• GSM-R, GSM, DCS, TDMA, PCS, UMTS
Frequency Range(J1- J2) 870 ~ 2170MHz
Insertion Loss 0.1dB Max.
Return Loss 20dB Min.
Frequency Range(J1–J3) 870 ~ 960MHz
Coupling Value 30.0 ± 0.4dB
J1 – J2(Thru) J1 - J3(870 ~ 960MHz) S21 : Coupling
Directivity 20dB Min.
Frequency Range(J2–J4) 1710 ~ 2170MHz
Coupling Value 30.0 ± 0.5dB
Directivity 20dB Min.
J1 - J3(870 ~ 960MHz)S21 : Isolation
J2 – J4(1710 ~ 2170MHz)S21 : Coupling
Passive IM(2-Ton@43dBm/tone) -163dBc Min.
Ingress Protection IP 67 J2 – J4(1710 ~ 2170MHz)S21 : Isolation
Passive IM
Head Office & Factory - Location : Incheon-City, Korea Tel : +82-32-816-1456 E-mail : [email protected]
Copyright 2010. Innertron, Inc. All rights Reserved
2 0 1 0 M A R C H
• HYBRID COMBINERPRODUCT GUIDEP/N : IT-125L001
D E S C R I P T I O N S
Hybrid Combiner is a 3dB high power
hybrid with an integral high performance
low PIM termination. The PIM specification
is 155dBc with two (2)+43dBm inputs.
Hybrid combiner can be used to combine
any two signals in the band without
interaction of the signals. This unit is
intended for indoor or outdoor environment
applications. The frequency range can
cover PCS & AWS with rated power of 50W
S P E C I F I C A T I O N S
Frequency Range 1710~2200MHz
C H A R A C T E R I C S T I C S
p
at each of two inputs.
Return Loss 18dB Min.
Hybrid Imbalance 0.5dB Max.
Insertion Loss 3.5dB Max.
PIMD (2x43dBm) 155dBc Min.
Input Power 50W
Ingress Protection IP65
Temperature Range -40 ~ +60p g
Connectors 7/16 DIN Female
Head Office & Factory - Location : Incheon-City, Korea Tel : +82-32-816-1456 E-mail : [email protected]
Copyright 2010. Innertron, Inc. All rights Reserved
2 0 1 0 A P R I L
• TOWER MOUNTED AMPLIFIERTMA 900 (25M)
P/N : IT-112C-002
PRODUCT GUIDE
D E S C R I P T I O N S
TMA is Dual duplex to allow on TMA one
transmission cable for both Tx and Rx. LNA
(Low Noise Amplifier) in the Rx path is Balanced
type. It contains alarm circuit to check LNA’
status. To compensate cable loss from antenna p
to BTS, TMA exhibits low NF (Noise Figure) and
high IP3 (3rd Order Intercept Point).
LOW INSERTION LOSS
LOW NOISE & HIGH IP3
INCLUDE LIGHTNING PROTECTION (ALL Port)
INDOOR OR OUTDOOR APPLICATIONS
S P E C I F I C A T I O N S B L O C K D I A G R A M
INDOOR OR OUTDOOR APPLICATIONS
Frequency BandRx 890~915 MHz
Tx 935~960 MHz
Bandwidth 25 MHzTX Insertion Loss 0.4dB, typical.
Tx Return Loss 18 dB, Min.
RX Gain 12± 1.0dB RX Gain Ripple ± 0.5dB (0.3)By-pass mode -2.3dB (1.8)
Rx Return Loss18 dB, Min.(Normal)15 dB, Min(By-pass)
Noise Figure
(90% of BW in the center)1.7dB (1.5) typ.(2.0dB @Temp.)
OIP3 +23dBm min.(1tone=0dBm)
P1dB +12dBm min.
PIMD @2-tone * 20W 160dBc
Input Power (Avg. / peak) 200W / 2kW
DC Supply +12Vdc / 120mA typ.
AlarmAlarm1 220 mA, ±25mAAlarm2 320 mA, ±25mA
IP rating IP67Lightning protection 5 kA, 8/20 μs pulseConnectors 7/16 Din (Female)( )
Size407.5 (313.5) X 225 X 117.5 (94.5)
(Including Bracket)
Weight Approximate 7.5kg
Operating Temperature -40∼+60
Head Office & Factory - Location : Incheon-City, Korea Tel : +82-32-816-1456 E-mail : [email protected]
Copyright 2010. Innertron, Inc. All rights Reserved
2 0 1 0 M A Y
• EGSM/DCS DUAL BAND REPEATER
P/N : IT-109J-002
PRODUCT GUIDE
D E S C R I P T I O N S
The Innertron EGSM/DCS Dual Band Repeater
is idea for indoor coverage extension applied to
GSM900/DCS1800 cellular communication
systems. It can boost signal up to 65dB and
drive RF output power up to 10dBm. It is a very
O U T L I N E D R A W I N G
drive RF output power up to 10dBm. It is a very
effective and cost effective solution for indoor
coverage application.
• Power Overload Protection• Optimized Gain and Maximized Performance• Exceptional Coverage – Low NF• Applicable to CDMA PCS GSM DCS• High Reliability
S P E C I F I C A T I O N S
O U T L I N E D R A W I N G• High Reliability• Design to Increase Signal Strength
EGSM900 DCS1800
Uplink Downlink Uplink Downlinkp p
Frequency880-
915MHz925-
960MHz1710-
1785MHz 1805-
1880MHz
Gain 65dB
Noise Figure 8dB Max
Max. Output Power
+10dBm
Max. Input Power
-35dBm (Auto Shutdown @ Overpower)
G i Fl TBD
Top
Gain Flatness TBD
Return Loss 10dB (min.)
ALC Level +11dBm
ALC Level Range
20dB
Power Delay 5 Sec
Supply DC 3.5V
Power BottomPowerConsumption
TBD
I/O Connecter SMA(F)
InputImpedance
50 Ohm
Bottom
Head Office & Factory - Location : Incheon-City, Korea Tel : +82-32-816-1456 E-mail : [email protected]
Copyright 2010. Innertron, Inc. All rights Reserved
2 0 1 0 J U L Y
• C I B D U P L E X E RPRODUCT GUIDEP/N : IT-127X001
D E S C R I P T I O N S
CIB Duplexer
• Low Insertion Loss
• Small Size, Low Spurious
Wid O ti T t R• Wide Operating Temperature Range
• Customization available
• High reliability
• Very good PIMD
• Indoor & Outdoor Application
• Fully RoHS Compliant
S P E C I F I C A T I O N S
Frequency Band (800MHz) 810~960MHz
F B d (2GH ) 1920 2170MH
C H A R A C T E R I C S T I C S
Frequency Band (2GHz) 1920~2170MHz
Insertion Loss (800MHz) 0.1dB Max.
Insertion Loss (2GHz) 0.15dB Max.
VSWR (800MHz / 2GHz) 1.2 Max.
Rejection(800MHz) 60dB Min@1920~2130MHz
Rejection(2GHz) 65dB Min@815~925MHz
Impedance(800MHz /2GHz) 50 Ohms
PIMD (800MHz) -103dB Min
Impedance(800MHz /2GHz) 50 Ohms
Connector Type RF Port 7/16 Female
MTBT 10 Million Hours
Safety EN 60 950Safety EN 60 950
Environmental ETS 300 019
Ingress Protection IP67
Head Office & Factory - Location : Incheon-City, Korea Tel : +82-32-816-1456 E-mail : [email protected]
Copyright 2010. Innertron, Inc. All rights Reserved
PRODUCT GUIDE2 0 1 0 N O V E M B E R
• CROSS COMBINER (DIPLEXER)
P/N : IT-125N001
D E S C R I P T I O N S
Innertron Combiner is a two inputDiplexer which allows combination andseparation of the signals in each wirelessband. The inputs are well isolated andhave minimal insertion loss over theirrespective frequency bands to minimizeband inter-reaction. The Combiner isdesigned using passive, proprietarytechniques which minimize cost and size.
• Low Insertion loss & Low IMD
• High Power Solution
Customization Available
S P E C I F I C A T I O N S C H A R A C T E R I C S T I C S
Parameter Specification
Low Band High Band
• Customization Available
Low Band
Low Band
Low Band High Band
Frequency 1710 - 2170 MHz
2300 - 2690 MHz
Insertion Loss 0.2 dB Max. 0.2 dB Max.
R t L
20dB Min.(Common Port.)
Low BandReturn Loss20dB Min.(Low Port.)
20dB Min.(High Port.)
Isolation 50 dB Min.
Passive IM -117 dBm Max. (2-Tone@43dBm/tone)
RF
High Band
RFConnectors DIN 7/16 Female, Long Barrel
Head Office & Factory - Location : Incheon-City, Korea Tel : +82-32-816-1456 E-mail : [email protected]
Copyright 2010. Innertron, Inc. All rights Reserved
2 0 1 0 N O V E M B E R
P/N : IT-125K001
• CROSS COMBINER (TRIPLEXER)PRODUCT GUIDE
D E S C R I P T I O N S
Innertron Combiner is a three inputTriplexer which allows combination andseparation of the signals in each wirelessband. The inputs are well isolated and haveminimal insertion loss over their respective
C H A R A C T E R I C S T I C S
frequency bands to minimize band inter-reaction. The Combiner is designed usingpassive, proprietary techniques whichminimize cost and size.
• Low Insertion loss & Low IMD
• High Power Solution
Low Band
S P E C I F I C A T I O N S
Parameter Specification
Low Band Mid Band High Band
• Customization Available
Mid Band
Frequency1710 -1880 MHz
1920 -2170 MHz
2300 –2690 MHz
Insertion Loss 0.3 dB Max. 0.3 dB Max. 0.2 dB Max.
Return Loss
20dB Min.(Common Port.)
Mid Band
etu oss20dB Min.(Low Port.)
20dB Min.(Low Port.)
20dB Min.(High Port.)
Power (Avg./Peak) 300w/3kW 300w/3kW 200W/2kW
Isolation 50 dB Min. 50 dB Min. 50 dB Min.
High Band
Passive IM -117 dBm Max. (2-Tone@43dBm/tone)
RF Connector DIN 7/16 Female, Long Barrel
Head Office & Factory - Location : Incheon-City, Korea Tel : +82-32-816-1456 E-mail : [email protected]
Copyright 2010. Innertron, Inc. All rights Reserved
2 0 1 0 N O V E M B E R
• H I G H P A S S F I L T E RPRODUCT GUIDEP/N : IT-114A001
D E S C R I P T I O N S
Innertron High Pass Filter covers the
frequency range from 2400MHz to
8000MHz. It includes outstanding
C H A R A C T E R I C S T I C S
performance and low insertion loss
by using special design techniques.
• Low Insertion Loss
• Customization Available
-25
S P E C I F I C A T I O N S
Parameter Specification +65Parameter Specification
Band Pass 2400~8000 MHz
Insertion Loss 1.5dB Max.
65
Return Loss 14.0 dB Min.
Attenuation 30 dB Min. 136~512MHz
+25
Passive IMD -105dBm
Head Office & Factory - Location : Incheon-City, Korea Tel : +82-32-816-1456 E-mail : [email protected]
Copyright 2010. Innertron, Inc. All rights Reserved
• 6 W A Y D I V I D E R
P/N : IT-124N004
2 0 1 0 N O V E M B E R
PRODUCT GUIDE
D E S C R I P T I O N S
Innertron 6-way dividers cover thefrequency range from 700MHz to2700MHz.It includes outstanding amplitude andlow insertion loss and power handlinglow insertion loss, and power handlingcapability of up to 5 Watts at thecommon port by using special designtechniques.
• Customization Available
• Minimal Insertion Loss
High Isolation
S P E C I F I C A T I O N S
Insertion Loss Return Loss
• High Isolation
• Power Rating of 5 Watts
C H A R A C T E R I C S T I C S
Parameter Specification
Frequency 700~2700MHz
Insertion Loss 9.0dB Max.
Insertion Loss, Return Loss
Amplitude Balance 0.8dB Max.
VSWR(All Port) 1.4 : 1 Max.
Isolation 20dB Min.
Isolation
Input Power 5W(Avg.)
Head Office & Factory - Location : Incheon-City, Korea Tel : +82-32-816-1456 E-mail : [email protected]
Copyright 2010. Innertron, Inc. All rights Reserved
P/N : IT-103K007
2 0 1 0 N O V E M B E R
PRODUCT GUIDE • D U A L B A N D D I P L E X E R
D E S C R I P T I O N S
Innertron Combiner is a two input Diplexerwhich allows combination and separation ofthe signals in each wireless band. The inputsare well isolated and have minimal insertionloss over their respective frequency bands tominimize band inter-reaction. The Combineris designed using passive, proprietarytechniques which minimize cost and size.
• Low Insertion loss & Low IMD
• High Power Solution
• Customization Available
Insertion Loss Return Loss
S P E C I F I C A T I O N S C H A R A C T E R I C S T I C S
Low Band 824 MHz ~ 2170 MHz
0.25 dB, max. @ 800MHz
0.25 dB, max. @ 900MHz
• Customization Available
BPF Band
Insertion Loss, Return LossInsertion Loss0.25 dB, max. @ 900MHz
0.5 dB, max. @ 1800MHz
0.5 dB, max. @ 2100MHz
Return Loss 18 dB, min.
Isolation 45dB, min. (Port2-1)
Avg. Input Power 150W @ Port 1
High Band (2400 MHz ~ 2500 MHz)
Isolation
Insertion Loss 0.5 dB, max.
Return Loss 20 dB, min.
Isolation 45dB, min. (Port 2-1)
PIMD -150 dBc for two 20W carriers
Avg. Input Power 150 W @ Port 2
Connector N-J
BRF Band
Head Office & Factory - Location : Incheon-City, Korea Tel : +82-32-816-1456 E-mail : [email protected]
Copyright 2010. Innertron, Inc. All rights Reserved
Operating Temp. -10 ~ +60
Relative Humidity 0 ~ 95%
Protection IP67
2 0 1 1 J A N U A R Y
PRODUCT GUIDE • C o m b i n e r B o x P O I - 0 8 0 4
D E S C R I P T I O N S
Innertron Combiner Box has been designedfor in-building system. Providing all outputsare utilized, the total loss for separate pathis less than 1 dB by using of 4x4 Low Band
C H A R A C T E R I C S T I C S
& 4x4 High Band Hybrid Combiner and 4Diplexers.
• 8 Inputs to 4 Combined Outputs
• Secured PIM, and Low Loss
• Customization Available1. LOW IN1 2. LOW IN2
Insertion Loss Return Loss
S P E C I F I C A T I O N S
Parameter Specification
Inputs L1 to L4 698-960 MHz, Low Band
3. LOW IN 3 4. LOW IN 4
Insertion Loss, Return LossInputs H1 to H4 1710-2700 MHz, High Band
Input Isolation, dBWithin Low Band : 24 typ., 22dB min.
Within High Band : 22 typ., 20 dB min.
Between Bands >55 dB
Input Return Loss >19dB (>21 dB typical)
Coupling (In-Out) 6 5 ± 0 8 dB (all paths)
5. High IN1 6. High IN2
Isolation
Coupling (In Out) 6.5 ± 0.8 dB (all paths)
Power per input <60W avg., 3 kW peak
Total power in <200 W average
Impedance 50 Ω nominal
Environment -15 to +65, Indoor
PIM (Intermod) <-142 dBc (+43dBm x2)
8. High IN47. High IN3
Head Office & Factory - Location : Incheon-City, Korea Tel : +82-32-816-1456 E-mail : [email protected]
Copyright 2010. Innertron, Inc. All rights Reserved
FinishHousing: RoHS coated aluminum
Connectors: Triplate, N
Weight 22Ibs (10 kg) nominal