2019 CHALLENGER QUICK REFERENCE GUIDE

Vehicle User Guide — If EquippedTo access the Vehicle User Guide on yourUconnect Touchscreen: Tap the Uconnect Appsbutton, then tap the Vehicle User Guide icon onyour touchscreen. No Uconnect registration isrequired.

NOTE:Vehicle User Guide features are not availablewhile the vehicle is moving.

Features

• Your User Guide — Updated in real-time

• Available when and where you need it

• Touchscreen convenience

• Customizable interface

• Maintenance schedules and information

• Multilingual

• Comprehensive icon & symbol glossary

Keyless Enter-N-Go — PassiveEntry

The Keyless Enter-N-Go system is an enhance-ment to the vehicle’s key fob. This feature allowsyou to lock and unlock the vehicle’s door(s) andtrunk without having to press the key fob lock orunlock buttons.

To Unlock From The Driver OrPassenger Side

Uconnect 4C NAV With 8.4–inch DisplayVehicle User Guide Touchscreen Icon

Grab The Door Handle To Unlock

V E H I C L E U S E R G U I D E — I FE Q U I P P E D

P A S S I V E E N T R Y

• With a valid Keyless Enter-N-Go key fob locatedoutside the vehicle and within 5 ft (1.5 m) ofthe driver or passenger side door handle, grabeither front door handle to unlock the doorautomatically.

To Lock The Vehicle• Both front door handles have buttons located

on the outside of the handle. With one of thevehicle's Keyless Enter-N-Go key fobs locatedoutside the vehicle and within 5 ft (1.5 m) ofthe driver's or passenger front door handle,push the door handle button to lock the twodoors and trunk.

• Do NOT grab the door handle, when pushingthe door handle button. This could unlock thedoor(s).

NOTE:

• If “Unlock All Doors 1st Press” is programmed,all doors will unlock when you grab hold of thefront driver's door handle. Additionally, alldoors and the trunk will unlock with this optionprogrammed when you push the trunk button.

• If a key fob is detected in the vehicle whenlocking the vehicle using the power door lockswitch, the doors and trunk will unlock, and thehorn will chirp three times. On the third at-tempt, your key fob can be locked inside thevehicle.

• After pushing the Keyless Enter-N-Go lock but-ton, you must wait two seconds before you canlock or unlock the vehicle using the doorhandle. This is done to allow you to check if thevehicle is locked by pulling the door handlewithout the vehicle reacting and unlocking.

• If a Keyless Enter-N-Go door handle has notbeen used for 72 hours, the Keyless Enter-N-Go feature for that handle may time out.Pulling the deactivated front door handle willreactivate the door handle's Keyless Enter-N-Go feature.

Push The Button To Lock

Do NOT Grab The Handle When Locking

To Enter The Trunk

• With a valid Keyless Enter-N-Go key fob locatedoutside the vehicle and within 5 ft (1.5 m) ofthe deck lid, push the button located on thecenter of the light bar which is located on thedeck lid above the license plate.

For further information, and applicable warningsand cautions, please refer to the Owner’s Manual atwww.mopar.com/en-us/care/owners-manual.html(U.S. Residents) or www.owners.mopar.ca (Cana-dian Residents).

Instrument Cluster Display

The instrument cluster display features an inter-active driver display that is located in the instru-ment cluster. Pushing the controls on the left sideof the steering wheel allows the driver to selectvehicle information and Personal Settings.

Trunk Release Button

Instrument Cluster Display Controls

I N S T R U M E N T C L U S T E RD I S P L AY

• Push the up button to scroll upward through themain menus (Speedometer, mph/km/h, VehicleInfo, Performance Pages – SRT only, DriverAssist, Fuel Economy, Trip A, Trip B, Audio,Stored Messages, Screen Set Up).

• Push the down button to scroll downwardthrough the main menu and submenus (Speed-ometer, mph/km/h, Vehicle Info, Driver Assist,Fuel Economy, Trip A, Trip B, Audio, StoredMessages, Screen Set Up).

• Push the right button to access the informationscreens or submenu screens of a main menuitem.

• Push the left button to access the informationscreens or submenu screens of a main menuitem.

• Push the OK button to access/select the infor-mation screens or submenu screens of a mainmenu item. Push and hold the OK button fortwo seconds to reset displayed/selected fea-tures that can be reset. Pushing OK button willalso toggle between mph and km/h on thedigital speedometer.

Compass Calibration

This compass is self-calibrating, which eliminatesthe need to set the compass manually. When thevehicle is new, the compass may appear erratic,and the cluster will display dashes (- -) until thecompass is calibrated.

You may also calibrate the compass by completingone or more 360 degree turns (in an area free fromlarge metal or metallic objects) until the dashes (- -)displayed in the cluster turn off. The compass willnow function normally.

For further information, and applicable warningsand cautions, please refer to the Owner’s Manual atwww.mopar.com/en-us/care/owners-manual.html(U.S. Residents) or www.owners.mopar.ca (Cana-dian Residents).

Pairing ProcedureMobile phone pairing is the process of establish-ing a wireless connection between a cellularphone and the Uconnect system.

Start Pairing Procedure On The Radio

Uconnect 4 With 7-inch Display

1. Place the ignition in the ACC or ON position.

2. Press the “Phone” button.

3. Select “Settings.”

4. Select “Paired Phones.”

Uconnect 4 With 7-Inch Display

P H O N E P A I R I N G

5. Select “Add device.”

• Uconnect Phone will display an “In progress”screen while the system is connecting.

Uconnect 4C & 4C NAV With 8.4-inch Display

1. Place the ignition in the ACC or ON position.

2. Press the “Phone” button in the Menu Bar onthe touchscreen.

3. Select “Pairing.”

4. Select “Paired Phones And Audio Devices.”

5. Select “Add Device.”

• Uconnect Phone will display an “In progress”screen while the system is connecting.

Pair Your iPhone:

To search for available devices on your Bluetoothenabled iPhone:

1. Press the Settings button.

2. Select Bluetooth.

• Ensure the Bluetooth feature is enabled.Once enabled, the mobile phone will beginto search for Bluetooth connections.

3. When your mobile phone finds the Uconnectsystem, select “Uconnect”.

Complete The iPhone Pairing Procedure:

1. When prompted on the mobile phone, acceptthe connection request from Uconnect Phone.

NOTE:Some mobile phones will require you to enter thePIN number.

Uconnect 4C & 4C NAV With 8.4-Inch Dis-play

Bluetooth On/Uconnect Device Pairing Request

Pair Your Android Device:

To search for available devices on your Bluetoothenabled Android Device:

1. Push the Menu button.

2. Select Settings.

3. Select Connections.

4. Turn Bluetooth setting to “On.”

• Ensure the Bluetooth feature is enabled.Once enabled, the mobile phone will beginto search for Bluetooth connections.

5. Once your mobile phone finds the Uconnectsystem, select “Uconnect”.

• You may be prompted by your mobile phoneto download the phonebook, check “Do NotAsk Again” to automatically download thephonebook. This is so you can make calls bysaying the name of your contact.

Complete The Android Pairing Procedure:

1. Confirm the passkey shown on the mobilephone matches the passkey shown on theUconnect system then accept the Bluetoothpairing request.

NOTE:Some mobile phones require the PIN to be en-tered manually, enter the PIN number shown onthe Uconnect screen.

NOTE:Software updates on your phone or the Uconnectsystem may interfere with the Bluetooth connec-tion. If this happens, simply repeat the pairingprocess. However, first, make sure to delete thedevice from the list of phones on your Uconnectsystem. Next, be sure to remove Uconnect fromthe list of devices in your phone’s Bluetooth set-tings.

For further information on Uconnect Phone,please refer to “Uconnect Phone” in the vehicle’sUser Guide.

Uconnect Device

Pairing Request

Automatic High Beam —If Equipped

This system automatically controls the operationof the headlamp high beams as oncoming vehiclesapproach.

• The Automatic High Beam Headlamp Controlcan be turned on or off using the UconnectSystem.

• Push the turn signal lever away from you.

• With the headlight switch in the “AUTO” posi-tion, the high beams are controlled automatically.

• Pull the turn signal lever toward you to manu-ally deactivate the system.

• To improve system recognition of crossing traf-fic, and to limit use in a residential area, thevehicle must be moving at a speed greater than20 mph (32 km/h) before the Automatic HighBeam Module (AHBM) begins requesting highbeam activation.

NOTE:If the windshield or Automatic High Beam Head-lamp Control mirror is replaced, the mirror mustbe re-aimed to ensure proper performance. See anlocal authorized dealer.

For further information, and applicable warningsand cautions, please refer to the Owner’s Manual atwww.mopar.com/en-us/care/owners-manual.html(U.S. Residents) or www.owners.mopar.ca(Canadian Residents).

Adaptive Cruise Control (ACC) —If EquippedIf your vehicle is equipped with Adaptive CruiseControl, the controls operate exactly the same asthe standard cruise control, with one difference.You can set a specified distance you would like tomaintain between you and the vehicle in front ofyou.

• If the ACC sensor detects a vehicle ahead, ACCwill apply limited braking or acceleration auto-matically to maintain a preset following dis-tance while matching the speed of the vehicleahead.

NOTE:Your vehicle will not exceed the cruise speed youhave set.

L I G H T S S P E E D C O N T R O L

• If the sensor does not detect a vehicle directlyahead of you, it functions like a standard cruisecontrol system, maintaining the speed you set.

For further information, and applicable warningsand cautions, please refer to the Owner’s Manual atwww.mopar.com/en-us/care/owners-manual.html(U.S. Residents) or www.owners.mopar.ca (Cana-dian Residents).

Forward Collision Warning —If Equipped

The Forward Collision Warning (FCW) system pro-vides the driver with audible warnings, as well asvisual warnings within the instrument cluster dis-play, to warn the driver when a potential frontalcollision is detected. The warnings are intended toprovide the driver with enough time to react, toavoid or mitigate the potential collision.

FCW monitors the information from the forwardlooking sensors, as well as the Electronic StabilityControl (ESC) system, to calculate the probabilityof a forward collision. When the system deter-mines that a forward collision is probable, thedriver will be provided with the audible and visualwarnings.

NOTE:The FCW feature can be customized and turnedoff through the Uconnect System touchscreen.

Adaptive Cruise Switches

1 — Adaptive Cruise Control (ACC)On/Off2 — Distance Setting – Decrease3 — Distance Setting – Increase

S A F E T Y F E AT U R E S

For further information, and applicable warningsand cautions, please refer to the Owner’s Manual atwww.mopar.com/en-us/care/owners-manual.html(U.S. Residents) or www.owners.mopar.ca (Cana-dian Residents).

SRT VehiclesChassis

• Wheels - due to the high performance nature ofthe brake system, the wheels will get coatedwith brake dust. It is recommended thatMopar® Wheel Cleaner be used on your wheelsto avoid any possible damage to the finish.However, do not use wheel cleaner if yourvehicle is equipped with Dark Vapor or BlackSatin Chrome wheels, which must only becleaned with mild soap, water, and a soft cloth.

NOTE:Due to the high performance nature of the brakeson your SRT, vehicle dust and some noise areexpected and normal.

• Tire Service Kit - your vehicle comes with a tireinflator kit; there is no spare tire included inyour vehicle.

• Trailer Tow - Trailer towing with your SRT vehicleis not recommended.

• ESC (Electronic Stability Control) - your vehicleis equipped with selectable ESC modes. TheESC mode selected will alter the handling char-acteristics of your vehicle.

• Adjustable Modes - your vehicle is equipped withselectable driving modes: Default (Street), Sport,Track, Custom, ECO, and Valet. Please refer tothe Owner’s Manual for further information.

• Three-Season Tires - This vehicle may beequipped with three-season tires to enhanceperformance. FCA US LLC does not recom-mend use of these tires when temperatures arebelow 40°F (4°C) or in snow/ice conditions.

Powertrain & Drivetrain

• Engine & Transmission (SRT Engine Break-InRecommendations) - The following tips will behelpful in obtaining optimum performance andmaximum durability for your new SRT Vehicle.Despite modern technology and World Classmanufacturing methods, the moving parts ofthe vehicle must still wear in with each other.This wearing in occurs mainly during the first500 miles (805 km) and continues through thefirst oil change interval.

NOTE:Check engine oil with every refueling and add ifnecessary. Oil and fuel consumption may behigher through the first oil change interval.

S T A R T I N G A N D O P E R AT I N G

• Engine Oil - 0W-40 Full Synthetic Engine Oilrecommended.

• Fuel - for optimum performance, PremiumFuel with a minimum octane rating of 91 PumpOctane Number is recommended.

Automatic Transmission:

• Applying the brake and throttle pedals at thesame time [“brake torquing”] for an extendedperiod of time will illuminate the ETC fault lightrequiring the dealership to clear.

• The vehicle may be equipped with steeringwheel mounted “Paddle Shifters” and an Mgate console shifter. When in the M gate, thevehicle will not shift at red line and must bemanual shifted with either the paddle shiftersor the console shifter. In the M gate, the shiftlight can be programed to assist the driver withoptimal shift points.

Launch Control:

• Your car may be equipped with Launch Controlto improve acceleration performance. It is acti-vated by pressing the LAUNCH or Super TrackPack (if equipped) button, located in the in-strument panel switch bank, as well as in the

radio within “Race Options”, and will helpcontrol tire spin for maximum acceleration. Thelaunch RPM is also selectable through the raceoptions screens. Launch Control is not avail-able for the first 500 miles of vehicle life.

Manual Transmission:

• Your vehicle is equipped with a 1-4 skip shiftfeature to maximize fuel economy. Under cer-tain conditions, the vehicle will require you toshift the transmission from first to fourth gear,instead of from first gear to second gear. SkipShift is only active while in normal or defaultdriving mode. The detailed conditions of thisfeature are described in the Owner’s Manual.

• Do not attempt to shift the transmission if therear wheels are spinning due to loss of traction.Damage to the transmission may occur.

• When shifting, fully depress the clutch pedaland lift off the accelerator pedal before shiftinggears. Damage to the transmission or clutchmay occur if you do not fully depress the clutchpedal and lift off the accelerator pedal whenshifting.

• Do not rest your hand on the gear shift knobwhile driving. This may cause premature wearof the transmission synchronizers.

• Do not rest your foot on the clutch pedal whiledriving. This may cause premature wear of theclutch.

Body & Exterior

• Fascias and Ground Effects - This vehicle has aunique exterior appearance, which includesSRT unique fascias and ground effects. Theseexterior components define the style and ap-pearance of your new vehicle. They also cause alower approach angle in the front of the vehicleand reduced ground clearance. Due to lowerground clearance, driving your vehicle up steepdriveways, approach ramps, or near parkingblocks may cause damage to the front fasciaand ground effects.

• If your vehicle is equipped with a SATIN FINISHExterior Body Paint: Use products made specifi-cally for satin paint, such as Swissvax OpaqueSatin Paint Wax and Dr. Beasley’s Satin Paintand Sealant. Reference Satin Finish Tips Card.

• Caution should be taken when driving throughwater or snow more than 4 inches (100 mm)deep to avoid any potential for damage to yourvehicle.

Electrical

• Your vehicle may be equipped with a premium“harman/kardon” sound system. Your audiomode can be configured using the radio.

• Your vehicle is equipped with SRT performancepages, Drive Modes, Performance Shift Indica-tion, Launch Control, and Valet Mode, whichare displayed in the instrument cluster and theradio.

• Valet Mode is offered on all SRT vehicles. Thedriver can activate and deactivate Valet Modelwith a four-digit PIN they create. Custom PIN’sare created with each use. If you forget yourPIN, disconnect the battery for five minutes toreset.

• Your vehicle may be equipped with a Red keyfob, in addition to the Black key fob. The Redkey is the only key that can unlock the fullhorsepower and torque potential of the SRTHellcat engine, while the Black key fob limitsthe driver to reduced engine output and reduc-tion of transmission shift schedules. In addi-tion, the Red key fob will unlock all the optionswithin Drive Modes. The Black key fob will limityour options within Drive Modes.

• If equipped with an Automatic Transmission,your vehicle offers an ECO mode. ECO modewill change the feel of the throttle response andshift patterns. Please see the Owner’s Manualfor further information on configuration that areautomatically adjusted.

For additional information, and applicable warningsand cautions, please refer to the Owner’s Manual atwww.mopar.com/en-us/care/owners-manual.html(U.S. Residents) or www.owners.mopar.ca (Cana-dian Residents) for further information.

Activation

Activate your account to enjoy advanced safety,security and convenience features.

1. Press the Apps icon on the bottom of yourin-vehicle touchscreen.

2. Select the “Activate Services” icon from yourlist of apps.

3. Select “Customer Care” to speak with aSiriusXM Guardian Customer Care agent whowill activate services in your vehicle, or select“Enter Email” to activate on the web.

Once you have activated your services, you’re onlya few steps away from using remote services.

S I R I U S X M G U A R D I A N — I FE Q U I P P E D

Download the Uconnect mobile app:

• Once downloaded, use your Owner Accountlogin and password to access the app.

• A PIN is required to execute remote services.

• Tap the “Location” button on the bottom menubar of the app to locate your vehicle or send adestination to your Uconnect Navigation (ifequipped).

• Tap the “Settings” side menu in the upper leftcorner of the app to bring up app settings andaccess the Assist Call Centers.

For further information:

• U.S. residents visit: siriusxm.com/guardian

• Canadian residents visit: siriusxm.ca/guardian/

FeaturesIn-Vehicle

SiriusXM Guardian enhances your ownership anddriving experience by connecting your vehicle toan operable network. When connected to an oper-able network, you have access to:

• SOS Call: Connect to a live agent who willcontacts emergency services and stay on theline with you until help arrives.

• Customer Care Assistance: Speak with a liveagent by pressing the ASSIST button on yourrearview mirror to get Roadside Assistance orsupport.

Remote Services

• Vehicle Finder helps you find where you parkedyour car.

• Send & Go allows you to send destinations toyour navigation system for easy access on thego.

• Remote Door Lock/Unlock lets you unlock orlock your doors from any distance.

• Remote Horn & Lights allows you to sound yourhorn and flash your lights to easily find your car.

• Receive monthly Vehicle Health Reports, andAlerts whenever a problem is detected underthe hood.

Security Services

• Receive text or email notifications if your vehi-cle's security alarm goes off.

• Receive stolen vehicle assistance, using GPStechnology to help authorities locate your ve-hicle if it is stolen.

Mobile App

SiriusXM Guardian remote services can be usedwith the Uconnect app from virtually anywhere.

For further information on SiriusXM Guardian orthe Uconnect mobile App, refer to your UconnectOwner’s Manual Supplement.

Vehicle Finder And Send & GoVehicle Finder

Vehicle Finder allows you to find the location ofyour vehicle. To find your vehicle:

1. Press the “Location” tab on the Uconnectmobile App bottom bar.

2. Select the “Vehicle” icon to determine thelocation of your vehicle.

3. Select the “Find Route” button that appears,once your vehicle is located.

4. Select your preferred Navigation app to route apath to your vehicle.

Send & Go

To send an address to your Uconnect Navigationusing the Uconnect mobile app:

1. Press the “Location” tab on the bottom bar ofthe Uconnect mobile app.

2. Type in the destination you would like to navi-gate to, or search through one of the categoriesprovided.

3. Select the destination you want to send fromthe list that appears.

4. Press the “Send To Vehicle” button, and thenconfirm the destination by pressing “Yes,” tosend the destination to the Uconnect Naviga-tion in your vehicle.

5. Finally, confirm the destination inside yourvehicle by pressing the “Go Now” option on thepop-up that appears on the touchscreen whenthe vehicle is started.

Amazon Alexa Integration

Alexa is Amazon’s cloud-based voice service and itlets you voice-command your Uconnect systemfrom just about anywhere you Alexa.

To link your Uconnect system to Amazon Alexa:

1. Download the Amazon Alexa app on youriPhone or Android.

2. Launch the app, then tap MENU, and go toSKILLS.

3. Search for your vehicle. Then tap “ENABLE.”

4. Select LINK ACCOUNT.

5. Log in using your vehicle’s Owner Account IDand password.

Examples of commands:

• “Alexa, ask Dodge Durango how much gas is inmy vehicle.”

• “Alexa, ask Jeep Grand Cherokee to send direc-tions to Iron Mountain to my vehicle.”

• “Alexa, ask Chrysler 300 to start my vehicle.”

A M A Z O N A L E X A — I FE Q U I P P E D

Android Auto Integration

With easy touchscreen navigation and voice rec-ognition, Android Auto brings useful informationand organizes it into simple cards that appear justwhen they are needed.

1. Download the Android Auto app from theGoogle Play store on your Android-poweredsmartphone.

2. Connect your Android powered smartphone toone of the media USB ports in your vehicle. Ifthe Android Auto app was not downloaded, itwill begin to download when you plug in yourdevice.

3. Once the device is connected and recognized,the “Phone” icon on the personalized menubar will automatically change to the AndroidAuto Icon.

Apple CarPlay Integration

Apple CarPlay is the smarter, safer way to use youriPhone to get directions with Apple Maps, listen toApple Music, make calls and send messages — allthrough the Uconnect touchscreen or with yourvoice through Siri.

To use CarPlay, make sure you are using iPhone5 or later, have Siri enabled in Settings, ensureyour iPhone is unlocked for the very first connec-tion only, and then follow these steps:

1. Connect your iPhone to one of the media USBports in your vehicle.

2. Once the device is connected and recognized,the “Phone” icon on the personalized menubar will automatically change to the CarPlayicon.

Android Auto

Apple CarPlay

A N D R O I D A U T O A N D A P P L EC A R P L AY — I F E Q U I P P E D

NOTE:

Long Press: Press and hold the VR button toactivate Siri or Google Assistant.

Short Press: Briefly tap the VR button to activatethe native Uconnect voice recognition system.

When using Android Auto or Apple CarPlay, besure to use the factory-provided cable that camewith your phone, as aftermarket cables may notwork.

NOTE:The Owner’s Mobile App content is applicable tovehicles sold in the U.S. market and are notavailable from the Canadian App Store or GooglePlay Store.

Key Features• Owner Information For Your Vehicle

• Accident Assistant

• Online Service Scheduling

• Roadside Assistance

• Maintenance History

• And More

To get this FREE application, go directly to theApp Store or Google Play Store and enter thesearch keyword “Dodge”.

The DRIVE DODGE Application is the essentialapp for owners of Dodge brand vehicles. The appputs driver and lifestyle information right in thepalm of your hand, anywhere you go. Whether it’s

providing information about specific product fea-tures, taking a tour through your vehicle’s equip-ment, staying up to date on your vehicle’s health,knowing what steps to take following an accident,or scheduling your next appointment, we knowyou’ll find the app an important extension of yourDodge vehicle. Simply download the FREE app,select your make and model and enjoy the ride.

Features/Benefits• Available for free on iOS and Android smart-

phones and tablets.

• Select Dodge brand vehicles from model year2011 to current model year.

• You can also add other Chrysler, Jeep, Ram,FIAT or Alfa Romeo vehicles.*

• Easy access to vehicle information anywhereyou go using categories, bookmarks, searchand an A-Z index.

• Vehicle information such as operating instruc-tions, maintenance, service history, vehiclecontrols and emergency procedures.

D R I V E D O D G E M O B I L E A P P

• Find a dealer or an FCA-certified repair facility.

• Easily document and email an accident report.

• A parking reminder that allows you to drop a pinon your location and navigate back to yourvehicle.

• Contact customer care with one click.

• Access to vehicle heritage, parts, accessories,and social media networks.

• Schedule your next service appointment.

• Available in English and Spanish.

*App supports selected vehicles from model year2011 to present.

To get this FREE application, go directly to theApp Store or Google Play Store and enter thesearch keyword “Dodge”.

Whether it’s providing information about specific

product features, taking a tour through your

vehicle’s heritage, knowing what steps to take

following an accident or scheduling your next appointment,

we know you’ll find the app an important extension of your

Dodge brand vehicle. Simply download the app, select your

make and model and enjoy the ride. To get this app, go directly

to the App Store® or Google Play® Store and enter the search

keyword “Dodge” (U.S. residents only).

www.dodge.com/en/owners (U.S.) provides special offers

tailored to your needs, customized vehicle galleries,

personalized service records and more. To get this information,

just create an account and check back often.

Get warranty and other information online – you can review and

print or download a copy of the Owner’s Manual, Navigation/

Uconnect manuals and the limited warranties provided by FCA

US LLC for your vehicle by visiting www.dodge.com/en/owners

(U.S.) or www.owners.mopar.ca (Canada). Click on the

applicable link in the “Popular Topics” area of the

www.dodge.com/en/owners (U.S.) or www.owners.mopar.ca (Canada) homepage and follow the instructions to select the

applicable year, make and model of your vehicle.

D O W N L O A D A F R E E E L E C T R O N I C C O P Y

O F T H E M O S T U P - T O - D A T E

O W N E R ’ S M A N U A L , M E D I A A N D

W A R R A N T Y B O O K L E T B Y V I S I T I N G :

WWW.MOPAR.COM/EN-US/CARE/OWNERS-MANUAL.HTML

(U .S . RES IDENTS)

WWW.OWNERS .MOPAR.CA (CANADIAN RES IDENTS)

DODGE.COM (U .S . )

DODGE.CA (CANADA)

©2018 FCA US LLC . ALL R IGHTS RESERVED.

DODGE IS A REGISTERED TRADEMARK OF FCA US LLC .

APP STORE IS A REGISTERED TRADEMARK OF APPLE INC .

GOOGLE PLAY STORE IS A REGISTERED TRADEMARK OF GOOGLE .

19

LA

-QR

G-A

A

SE

CO

ND

ED

ITIO

N