2d hand-held barcode scanner user guide · 2d handheld barcode scanner v1.01 31 / 66 aiming when...
TRANSCRIPT
2D Hand-held Barcode Scanner User Guide
2D Handheld Barcode Scanner V1.01
2 / 66
2D Handheld Barcode Scanner V1.01
3 / 66
Version History
Version Description Date
V1.0 Initial release.
2016-11-10
V1.01 Add Data Matrix and PDF417 2017-04-25
2D Handheld Barcode Scanner V1.01
4 / 66
Content
Chapter 1 Getting Started ......................................................................................................... 8
Introduction ............................................................................................................... 8
Feature ..................................................................................................................... 9
Application Field ......................................................................................................... 9
Data Interface ........................................................................................................... 10
Data Interface ........................................................................................................... 11
Chapter 2 Barcode Scanner Parameter ................................................................................. 12
Physical Parameter ..................................................................................................... 12
Physical Parameter ..................................................................................................... 14
Accessories .............................................................................................................. 15
Chapter 3 System Setting ..................................................................................................... 16
Introduction ............................................................................................................. 16
Factory Defaults ........................................................................................................ 17
To Enable or Disable Programming Code ......................................................................... 19
Transmit Programming Barcode Data .............................................................................. 19
Scanning Mode Setting ............................................................................................... 20
Beep Setting ............................................................................................................. 29
2D Handheld Barcode Scanner V1.01
5 / 66
Illumination ............................................................................................................. 30
Aiming ................................................................................................................... 31
Chapter 4 Communication Setting ....................................................................................... 32
Introduction ............................................................................................................. 32
USB-KBW Mode ...................................................................................................... 32
USB COM Port Emulation ........................................................................................... 34
RS232 serial communication interface ............................................................................. 34
Chapter 5 Data Edition ......................................................................................................... 37
Introduction ............................................................................................................. 37
Code ID .................................................................................................................. 38
Custom Prefix ........................................................................................................... 39
Custom Suffix ........................................................................................................... 41
End Characters Setting ................................................................................................ 43
Chapter 5 Symbologies ........................................................................................................ 44
Introduction ............................................................................................................. 44
Enable/Disable All Symbologies .................................................................................... 44
UPC-A ................................................................................................................... 45
UPC-E .................................................................................................................... 45
EAN-8 .................................................................................................................... 46
2D Handheld Barcode Scanner V1.01
6 / 66
EAN-13 .................................................................................................................. 46
Code 128 ................................................................................................................. 47
Code 39 .................................................................................................................. 47
Code 93 .................................................................................................................. 48
Code 11 .................................................................................................................. 48
Interleaved 2 of 5 ....................................................................................................... 48
Matrix 2 of 5 ............................................................................................................ 49
Industrial 2 of 5 ......................................................................................................... 49
Codabar (NW-7) ........................................................................................................ 50
MSI Plessey ............................................................................................................. 50
GS1 DataBar Limited (RSS Limited) .............................................................................. 50
GS1 DataBar Omnidirectional (RSS Omnidirectional) ......................................................... 51
GS1 DataBar Expanded (RSS Expanded) ......................................................................... 51
QR Code ................................................................................................................. 52
Data Matrix .............................................................................................................. 52
PDF 417 .................................................................................................................. 53
Chapter 6 Serial Commands ................................................................................................. 54
Introduction ............................................................................................................. 54
2D Handheld Barcode Scanner V1.01
7 / 66
Trigger a Command .................................................................................................... 54
Chapter 7 Appendix ............................................................................................................. 55
Appendix-Code ID ............................................................................................................... 55
Appendix-Command .................................................................................................. 57
Appendix-Digit Barcodes ............................................................................................. 58
Appendix- Save and Don’t Save Setting ........................................................................... 59
Appendix-ASCII Table ................................................................................................ 60
2D Handheld Barcode Scanner V1.01
8 / 66
Chapter 1 Getting Started
Introduction
This 2D barcode scanner is a universal 2D image barcode scanner, applies with CMOS
technology. This scanner easily scan the 1D codes, 2D codes on paper and plastic, also
screen codes.
2D Handheld Barcode Scanner V1.01
9 / 66
Feature
Can easily read mainstream 1D and 2D codes
Nice performance to scan the codes on paper, plastic card, LCD screen etc..
Humanization design: ergonomical design ensures easy and comfortable operation
Support auto-scanning with its’ own holder
Application Field
Medical, supermarket, retail trade, manufacturer, warehouse and logistics, electronic ticket
and mobile payment.
2D Handheld Barcode Scanner V1.01
10 / 66
Data Interface
This scanner applies with RJ45 10P10C interface, please check the picture below to have PIN definition and
description.
2D Handheld Barcode Scanner V1.01
11 / 66
Data Interface
This scanner must be operated with a connected main engine which refers to PC host, POS
and Android host etc.
USB Interface
RS232 Interface
2D Handheld Barcode Scanner V1.01
12 / 66
Chapter 2 Barcode Scanner Parameter
Physical Parameter
Light Source LED 625±10nm(aimer), 5600K LEDs(illumination)
CMOS 640 x 480 CMOS
Processor ARM32-bit
Resolution ≥4mil/0.1mm(PCS90%,CODE 39)
Depth of Field 10mm~650mm
Scanning Mode Trigger, Auto-scanning, Led-on
Promoting Mode Buzzer,Indicator(LED)
Scan Angle: Test Conditions:CODE39,10mil/0.25mm,PCS90%
Roll: ±360°, Pitch:±55°, Skew: ±50°
Print Contrast ≥25%
Ambient
illumination
0-10000LUX
Decode
Capability
1D:UPC-A,UPC-E,EAN-8,EAN-13, Code 128, GS1-128, Code
39,Code 93,Code 11,Interleaved 2 of 5,Matrix 2 of 5,Codabar
(NW-7),MSI, etc.
2D: QR Code,PDF417,Data Matrix,etc.
2D Handheld Barcode Scanner V1.01
13 / 66
2D Handheld Barcode Scanner V1.01
14 / 66
Physical Parameter
Weight <110g(Without USB)
Device
Dimension
150mm L * 70mm W * 95mm H
Interface USB(USB-KBW/USB-COM)、RS232
Cable Length 1.5m
Materials ABS
Color Black
Power
Voltage
DC 5V
Current 150mA(work time), 50mA(stand by)
User Environment
Operation Temperature -20℃ to 50℃
Storage Temperature -40℃ to 70℃
Relative Humidity 5% to 95%(non-condensing)
IP Level IP42
Drop test 1.2m, 100 times
Temperature test 30 minutes for high Temp., 30 minutes for low Temp.,
Highest temperature 60℃
Lowest temperature -20℃
Shock resistance 10H@125RPM
2D Handheld Barcode Scanner V1.01
15 / 66
Accessories
Cable(optional) USB cable
RS232 cable
Power Adapter(optional) Output:DC 5V, 1A;Input: AC 100~240V, 50~60Hz
Depth of field
Code Type Code Density Nearest Farthest
Code 39 0.1mm(4mil) 50mm 80mm
Code 39 0.127mm(5.0mil) 30mm 90mm
Code 39 0.5mm(20mil) 70mm 280mm
Code 39 1.0mm(40mil) 150mm 650mm
EAN-13 0.33mm(13.0mil) 40mm 230mm
QR Code 20mil 10mm 180mm
Data Matrix 10mil 10mm 70mm
PDF 417 6.88mil 20mm 70mm
Test condition:25℃indoor, ambient illumination200LUX,PCS=0.9
2D Handheld Barcode Scanner V1.01
16 / 66
Chapter 3 System Setting
Introduction
The scanner can be configured by scanning programming barcodes.
Manual introduction
Manual scanning mode, please follow the scanning steps:
1. Press and hold the trigger button, then the light is activated, and appear the red aiming
light and the white led light.
2. Aim the center of the codes by red aiming light, to move the scanner between the codes
to find the best scanning distance.
3. Decode successfully when you hear the buzzer sound and the red light will be off,the
codes will be transmitted to the host.
2D Handheld Barcode Scanner V1.01
17 / 66
Note:During scanning the same series codes, you will find there will be a highly success
rate between the scanner and the codes in some distance, this refers to the best reading
distance.
Factory Defaults
Scanning the following barcode can restore the scanner to the factory defaults.
You may need to reset your scanner when:
1. Scanner is not properly configured so that it fails to decode barcodes;
2. You forget previous configuration and want to avoid its impact;
3. Functions that are rarely used have been enabled for the time being.
Restore Factory Defaults
Check the version
Scanning the code to check the scanner version.
2D Handheld Barcode Scanner V1.01
18 / 66
Check the version
2D Handheld Barcode Scanner V1.01
19 / 66
To Enable or Disable Programming Code
Enable Programming Code*
Disable Programming Code
Transmit Programming Barcode Data
Programming barcode data can be transmitted to the Host. Scan the appropriate barcode below to
enable or disable the transmission of programming barcode data (i.e. the characters under programming
barcode) to the Host.
Restarting the engine will automatically disable the transmission of programming barcode data to the
Host.
Transmit Programming Barcode Data
Don’t Transmit Programming Barcode Data *
2D Handheld Barcode Scanner V1.01
20 / 66
Scanning Mode Setting
Manual Mode
If the Manual Mode is enabled, you could activate the scanner by providing an external
hardware trigger. When in manual mode, the scanner scans until a barcode is read, or until
the hardware trigger is released.
Stand By Mode
When you enable Stand By mode, the scanner will enter Stand By mode automatically when
the scanner stops scanning for 30 seconds, you can scan the programming code below to set.
Note: The default time for the scanner is 30 seconds, you can press the trigger to awake scanner, and the
scanner will be back to work.
Manual Mode*
Enable Stand By*
Disable Stand By
2D Handheld Barcode Scanner V1.01
21 / 66
Auto-scanning Mode
If the Auto-scanning Mode is enabled, the engine activates a decode session every time it
detects a change in ambient illumination. The decode session continues until the barcode is
decoded or the decode session timeout expires.
Driving the TRIG pin on the host interface connector low can also activate a decode session.
The decode session continues until the active trigger signal is no longer present or the
barcode is decoded or the decode session timeout expires. The trigger signal needs to be
negated before the engine is able to monitor ambient illumination again.
Auto-scanning Mode
Decode Session Timeout
This parameter sets the maximum time decode session continues during a scan attempt. If the
timeout expires or the barcode is decoded, the engine goes back to monitoring ambient
illumination. It is programmable in 0.1ms increments from 0.1s to 25.5s. When it is set to 0,
the timeout is infinite. The default setting is 5s.
1000ms
3000ms
2D Handheld Barcode Scanner V1.01
22 / 66
Timeout between Decodes (Same Barcode)
Timeout between Decodes (Same Barcode) can avoid undesired rereading of same barcode
in a given period of time. The following parameter sets the timeout between decodes for
same barcode. It is programmable in 0.1s increments from 0s to 25.5s. The default setting is
1.0s.
*5000ms
Infinite
Disable Timeout between Decodes
500ms
*1000ms
1500ms
2000ms
2D Handheld Barcode Scanner V1.01
23 / 66
Sensitivity
Sensitivity specifies the degree of acuteness of the engine’s response to changes in ambient
illumination. The higher the sensitivity, the lower requirement in illumination change to
trigger the engine. You can select an appropriate degree of sensitivity that fits the ambient
environment.
2D Handheld Barcode Scanner V1.01
24 / 66
Medium Sensitivity* Low Sensitivity
High Sensitivity
Enhanced Sensitivity
2D Handheld Barcode Scanner V1.01
25 / 66
Continuous Mode
This mode enables the engine to scan/capture, decode and transmit over and over again.
When the engine is operating in Continuous Mode, barcode reading can be
suspended/resumed through control over the trigger signal. When barcode reading is in
progress, negating the trigger signal after having maintained it for 30ms or longer will
suspend barcode reading; when barcode reading is suspended, performing the same control
over the trigger signal will resume barcode reading.
Continuous Mode
Decode Session Timeout
This parameter sets the maximum time decode session continues during a scan attempt. If the
timeout expires or the barcode is decoded, the engine goes back to monitoring ambient
illumination. It is programmable in 0.1ms increments from 0.1s to 25.5s. When it is set to 0,
the timeout is infinite. The default setting is 5s.
1000ms
3000ms
2D Handheld Barcode Scanner V1.01
26 / 66
*5000ms
Infinite
2D Handheld Barcode Scanner V1.01
27 / 66
Timeout between Decodes (Same Barcode)
Timeout between Decodes (Same Barcode) can avoid undesired rereading of same barcode
in a given period of time. The following parameter sets the timeout between decodes for
same barcode. It is programmable in 0.1s increments from 0s to 25.5s. The default setting is
1.0s.
Enable/Disable Timeout between Decodes (Same Barcode)
0ms
500ms
*1000ms
1500ms
2000ms
2D Handheld Barcode Scanner V1.01
28 / 66
Timeout between Decodes (Same Barcode)
To scan the programming code below to set timeout between decodes.
Enable Timeout between Decodes
Disable Timeout between Decodes*
Infinite
500ms
1000ms
3000ms
5000ms
2D Handheld Barcode Scanner V1.01
29 / 66
Beep Setting
On and off
There will be a prompting sound after scanning successfully, and the buzzer can be turned
off for user requirements.
On*
Off
Scan the programming code below to set the time of beep. The default time is 60ms.
30ms
60ms*
90ms
120ms
2D Handheld Barcode Scanner V1.01
30 / 66
Illumination
A couple of illumination options are provided to improve the lighting conditions during
every image capture:
Normal: Illumination LEDs are turned on during image capture.
Always ON: Illumination LEDs keep ON after the engine is powered on.
OFF: Illumination LEDs are OFF all the time.
Normal*
Always On
OFF
2D Handheld Barcode Scanner V1.01
31 / 66
Aiming
When scanning/capturing image, the engine projects an aiming pattern which allows
positioning the target barcode within its field of view and thus makes decoding easier.
Normal: The engine projects an aiming pattern only during barcode scanning/capture.
Always ON: Aiming pattern is constantly ON after the engine is powered on.
OFF: Aiming pattern is OFF all the time.
Normal*
Always On
OFF
2D Handheld Barcode Scanner V1.01
32 / 66
Chapter 4 Communication Setting
Introduction
The scanner provides a USB interface, USB-COM interface to communicate with the host
device. The host device can receive scanned data and send commands to control the scanner
or to access/alter the configuration information of the scanner via the USB interface.
USB-KBW Mode
To connect the scanner with the host by USB interface, you can scan USB HID-KBW
programming code to set scanner to USB output mode, and you don’t need to install any
drivers, just plug and play.
USB-KBW*
2D Handheld Barcode Scanner V1.01
33 / 66
USB Country Keyboard Types
Keyboard layouts vary from country to country. The default setting is U.S. keyboard.
U.S.*
Chech
France
Germany
Hungary
Italy
Japan
Spain
2D Handheld Barcode Scanner V1.01
34 / 66
USB COM Port Emulation
This feature allows the host to receive data in the way as a serial port does. However, you
need to set communication parameters on the scanner to match the Host requirements. A
driver is required for this feature.
USB-COM
RS232 serial communication interface
Serial communication interface is usually used to connect the scanner to a host device (like
PC, POS). When the scanner is connected to a host device through its RS-232 interface, you
need to set communication parameters to match the host device.
TTL/RS232
Please modify the parameter below when the parameter is different from Host device.
Parameter Default
RS232 Type Standard TTL/RS232
Baud Rate 9600
2D Handheld Barcode Scanner V1.01
35 / 66
Parity Type None
Data Bits 8
Stop Bits 1
Baud Rate
Baud rate is the number of bits of data transmitted per second. Set the scanner’s baud rate to
match the host requirements. All supported baud rate are listed below.
1200
4800
9600*
14400
19200
38400
2D Handheld Barcode Scanner V1.01
36 / 66
57600
115200
2D Handheld Barcode Scanner V1.01
37 / 66
Chapter 5 Data Edition
Introduction
After a successful barcode read, a string containing numbers, letters or symbols will be
returned. In real applications, barcode data may be found insufficient for your needs. You
may wish to include additional information such as barcode type, data acquisition time or
delimiter in data being scanned.Adding extra information to printed barcodes does not seem
like a sensible solution since that will increase the barcode size and make them inflexible.
Instead, we come up with the idea of appending prefix and suffix to the data without making
any change to barcodes. We will show you how to conduct the configuration in the following
sections.
Note: Customized data: <Prefix><Data><Suffix><Terminating Character>
2D Handheld Barcode Scanner V1.01
38 / 66
Code ID
Users usually need to know barcode type in the process of scanning, you can use Code ID prefix to
recognize the barcode type. Please read “Appendix A” for the reference of the Code ID corresponding
barcode type.
Transmit Code ID
Don’t transmit Code ID*
Factory Default Code ID
2D Handheld Barcode Scanner V1.01
39 / 66
Custom Prefix
Users can custom the prefix of the output code for your requirements. For example, when
you add prefix “AB” to barcode “123”, the host will receive “AB123”.
Note: Prefix and suffix can add 15 characters at most.
Transmit Custom Prefix
Don’t Transmit Custom Prefix*
Steps to add prefix
To set a custom prefix, scan the custom prefix barcode first, and then check the numeric
barcodes corresponding to the hexadecimal value of a desired prefix.
Custom Prefix
For example:When you add “VC” as prefix, the corresponding Hex value is
0x56/0x43)
A、Scan “Transmit Custom Prefix” programming code to start setting
B、Scan “Custom Prefix”
C、Scan the numeric barcodes “5”,“6”, “4” , “3”(See the “Digit Barcodes” section in Appendix)
D、You finished adding prefix
2D Handheld Barcode Scanner V1.01
40 / 66
2D Handheld Barcode Scanner V1.01
41 / 66
Custom Suffix
Users can custom the suffix of the output code for your requirements. For example, when
you add suffix “AB” to barcode “123”, the host will receive “AB123”.
Note: Prefix and suffix can add 15 characters at most.
Transmit Custom Suffix
Don’t Transmit Custom Suffix*
Steps to add suffix
To set a custom suffix, scan the custom suffix barcode first, and then check the numeric
barcodes corresponding to the hexadecimal value of a desired suffix.
Custom Suffix
For example:When you add “VC” as prefix, the corresponding Hex value is
0x56/0x43)
A、Scan “Transmit Custom Suffix” programming code to start setting
B、Scan “Custom Suffix”
C、Scan the numeric barcodes “5”,“6”, “4” , “3”(See the “Digit Barcodes” section in Appendix)
2D Handheld Barcode Scanner V1.01
42 / 66
D、You finished adding Suffix
2D Handheld Barcode Scanner V1.01
43 / 66
End Characters Setting
Add CR*
None
CR+NL
Add TAB(HT)
2D Handheld Barcode Scanner V1.01
44 / 66
Chapter 5 Symbologies
Introduction
Every symbology (barcode type) has its own unique attributes. This chapter provides
programming barcodes for configuring the scanner so that it can identify various barcode
symbologies. It is recommended to disable those that are rarely used to increase the
efficiency of the scanner.
Enable/Disable All Symbologies
If the Disable All Symbologies feature is enabled, the engine will not be able to read any
non-programming barcodes except the programming barcodes.
Enable All Symbologies
Disable All Symbologies
Open Default Symbologies*
2D Handheld Barcode Scanner V1.01
45 / 66
UPC-A
Enable/Disable UPC-A
Enable UPC-A*
Disable UPC-A
UPC-E
Enable/Disable UPC-E
Enable UPC-E0
Disable UPC-E0
2D Handheld Barcode Scanner V1.01
46 / 66
Enable/Disable UPC-E1
Enable UPC-E1
Disable UPC-E1
EAN-8
Enable/Disable EAN-8
Enable EAN-8*
Disable EAN-8
EAN-13
Enable/Disable EAN-13
2D Handheld Barcode Scanner V1.01
47 / 66
Enable EAN-13*
Disable EAN-13
Code 128
Enable/Disable Code 128
Enable Code 128*
Disable Code 128
Code 39
Enable/Disable Code 39
2D Handheld Barcode Scanner V1.01
48 / 66
Enable Code 39* Disable Code 39
Code 93
Enable/Disable Code 93
Enable Code 93*
Disable Code 93
Code 11
Enable/Disable Code 11
Enable Code 11
Disable Code 11*
Interleaved 2 of 5
2D Handheld Barcode Scanner V1.01
49 / 66
Enable/Disable Interleaved 2 of 5
Enable Interleaved 2 of 5
Disable Interleaved 2 of 5*
Matrix 2 of 5
Enable/Disable Matrix 2 of 5
Enable Matrix 2 of 5
Disable Matrix 2 of 5*
Industrial 2 of 5
Enable/Disable Industrial 2 of 5
Enable Industrial 2 of 5
Disable Industrial 2 of 5*
2D Handheld Barcode Scanner V1.01
50 / 66
Codabar (NW-7)
Enable/Disable Codabar
Enable Codabar*
Disable Codabar
MSI Plessey
Enable/Disable MSI Plessey
Enable MSI
Disable MSI*
GS1 DataBar Limited (RSS Limited)
Enable/Disable RSS Limited
2D Handheld Barcode Scanner V1.01
51 / 66
Enable RSS Limited*
Disable RSS Limited
GS1 DataBar Omnidirectional (RSS Omnidirectional)
Enable/Disable RSS-Omnidirectional
Enable RSS Omnidirectional*
Disable RSS Omnidirectional
GS1 DataBar Expanded (RSS Expanded)
Enable/Disable RSS Expanded
Enable RSS Expanded*
Disable RSS Expanded
2D Handheld Barcode Scanner V1.01
52 / 66
QR Code
Enable/Disable QR Code
Enable QR Code*
Disable QR Code
Data Matrix
Enable/Disable Data Matrix
2D Handheld Barcode Scanner V1.01
53 / 66
Enable Data Matrix*
Disable Data Matrix
PDF 417
Enable/Disable PDF 417
Enable PDF 417*
Disable PDF 417
2D Handheld Barcode Scanner V1.01
54 / 66
Chapter 6 Serial Commands
Introduction
The device must be set to a TTL-RS232 interface. The following commands can be sent via a PC COM port
using terminal emulation software.
Trigger a Command
1.Send command【7E 00 08 01 00 00 D5 AB CD】to enter Trigger mode.
2.Send command【7E 00 08 01 00 02 01 AB CD】to scan the barcode.
2D Handheld Barcode Scanner V1.01
55 / 66
Chapter 7 Appendix
Appendix-Code ID
No. Barcode Type Code ID Flag Address
1 UPC-A c 0x93
2 UPC-E0 c 0x94
3 UPC-E1 c 0x95
4 EAN-8 d 0x92
2D Handheld Barcode Scanner V1.01
56 / 66
5 EAN-13 d 0x91
6 CODE 128 j 0x96
7 Code 39 b 0x97
8 Code 93 i 0x98
9 Code 11 H 0x9D
10 Interleaved 2 of 5 e 0x9A
11 Matrix 2 of 5 v 0x9C
12 Industrial 2 of 5 D 0x9B
13 Codabar a 0x99
14 MSI Plessey m 0x9E
15 GS1 Databar (RSS-14) R 0x9F
16 GS1 Databar Limited(RSS) R 0xA0
17 GS1 Databar Expanded(RSS) R 0xA1
18 QR Code Q 0xA2
19 Data Matrix u 0xA3
20 PDF 417 r 0xA4
2D Handheld Barcode Scanner V1.01
57 / 66
Appendix-Command
Serial Command Function Return Value
7E 00 08 01 00 00 D4 AB CD Manual Mode
7E 00 08 01 00 00 D6 AB CD Continuous Mode
7E 00 08 01 00 00 D7 AB CD Auto-scanning Mode
7E 00 08 01 00 00 D3 AB CD No illumination
7E 00 08 01 00 00 DF AB CD Always-on Mode
7E 00 08 01 00 00 C7 AB CD No Aiming illumination
7E 00 08 01 00 00 F7 AB CD Aiming illumination Always On
7E 00 08 01 00 00 D5 AB CD To enter command scanning
mode
7E 00 08 01 00 02 01 AB CD Command trigger
7E 00 09 01 00 00 00 DE C8 Save
2D Handheld Barcode Scanner V1.01
58 / 66
Appendix-Digit Barcodes
0 1 2 3
4 5 6 7
8 9 A B
C D E F
2D Handheld Barcode Scanner V1.01
59 / 66
Appendix- Save and Don’t Save Setting
When you finished reading digit barcode, please scan “Save Digit Barcode” programming code to save the
setting. If you make a mistake when you read the digit barcodes, you can scan “cancel 1 present digit
barcode” to cancel the setting.
Save Digit Barcode
cancel 1 present digit barcode
cancel all present digit barcode
Cancel present setting
2D Handheld Barcode Scanner V1.01
60 / 66
Appendix-ASCII Table
Hex ASCII Value Characters
00 00 NUL (Null char.)
01 01 SOH (Start of Header)
02 02 STX (Start of Text)
03 03 ETX (End of Text)
04 04 EOT (End of Transmission)
05 05 ENQ (Enquiry)
06 06 ACK (Acknowledgment)
07 07 BEL (Bell)
08 08 BS (Backspace)
09 09 HT (Horizontal Tab)
0A 10 LF (Line Feed)
0B 11 VT (Vertical Tab)
0C 12 FF (Form Feed)
0D 13 CR (Carriage Return)
0E 14 SO (Shift Out)
0F 15 SI (Shift In)
10 16 DLE (Data Link Escape)
11 17 DC1 (XON) (Device Control 1)
12 18 DC2 (Device Control 2)
13 19 DC3 (XOFF) (Device Control 3)
14 20 DC4 (Device Control 4)
15 21 NAK (Negative Acknowledgment)
16 22 SYN (Synchronous Idle)
17 23 ETB (End of Trans. Block)
2D Handheld Barcode Scanner V1.01
61 / 66
18 24 CAN (Cancel)
19 25 EM (End of Medium)
1A 26 SUB (Substitute)
1B 27 ESC (Escape)
1C 28 FS (File Separator)
1D 29 GS (Group Separator)
1E 30 RS (Request to Send)
1F 31 US (Unit Separator)
20 32 SP (Space)
21 33 ! (Exclamation Mark)
22 34 " (Double Quote)
23 35 # (Number Sign)
2D Handheld Barcode Scanner V1.01
62 / 66
Hex ASCII Value Characters
24 36 $ (Dollar Sign)
25 37 % (Percent)
26 38 & (Ampersand)
27 39 ` (Single Quote)
28 40 ( (Right / Closing Parenthesis)
29 41 ) (Right / Closing Parenthesis)
2A 42 * (Asterisk)
2B 43 + (Plus)
2C 44 , (Comma)
2D 45 - (Minus / Dash)
2E 46 . (Dot)
2F 47 / (Forward Slash)
30 48 0
31 49 1
32 50 2
33 51 3
34 52 4
35 53 5
36 54 6
37 55 7
38 56 8
39 57 9
3A 58 : (Colon)
3B 59 ; (Semi-colon)
3C 60 < (Less Than)
3D 61 = (Equal Sign)
2D Handheld Barcode Scanner V1.01
63 / 66
3E 62 > (Greater Than)
3F 63 ? (Question Mark)
40 64 @ (AT Symbol)
41 65 A
42 66 B
43 67 C
44 68 D
45 69 E
46 70 F
47 71 G
48 72 H
49 73 I
4A 74 J
4B 75 K
2D Handheld Barcode Scanner V1.01
64 / 66
Hex ASCII Value Characters
4C 76 L
4D 77 M
4E 78 N
4F 79 O
50 80 P
51 81 Q
52 82 R
53 83 S
54 84 T
55 85 U
56 86 V
57 87 W
58 88 X
59 89 Y
5A 90 Z
5B 91 [ (Left / Opening Bracket)
5C 92 \ (Back Slash)
5D 93 ] (Right / Closing Bracket)
5E 94 ^ (Caret / Circumflex)
5F 95 _ (Underscore)
60 96 ' (Grave Accent)
61 97 A
62 98 B
63 99 C
64 100 d
65 101 e
2D Handheld Barcode Scanner V1.01
65 / 66
66 102 f
67 103 g
68 104 h
69 105 i
6A 106 j
6B 107 k
6C 108 l
6D 109 m
6E 110 n
6F 111 o
70 112 p
71 113 q
72 114 r
73 115 s
2D Handheld Barcode Scanner V1.01
66 / 66
Hex ASCII Value Characters
74 116 t
75 117 u
76 118 v
77 119 w
78 120 x
79 121 y
7A 122 z
7B 123 { (Left/ Opening Brace)
7C 124 | (Vertical Bar)
7D 125 } (Right/Closing Brace)
7E 126 ~ (Tilde)
7F 127 DEL (Delete)