2g 8000 - 8999 transmission alarms

7/25/2019 2G 8000 - 8999 Transmission Alarms

http://slidepdf.com/reader/full/2g-8000-8999-transmission-alarms 1/486

Nokia Siemens Networks

GSM/EDGE BSS, Rel.

RG20(BSS), OperatingDocumentation, Issue 03

Reference

Transmission Equipment Alarms (8000-

8999)

DN998797

Issue 8-1

Approval Date 2010-10-15

Confidential



2 DN998797

Issue 8-1

Transmission Equipment Alarms (8000-8999)

Id:0900d80580804cd6

Confidential

The information in this document is subject to change without notice and describes only the

product defined in the introduction of this documentation. This documentation is intended for the

use of Nokia Siemens Networks customers only for the purposes of the agreement under whichthe document is submitted, and no part of it may be used, reproduced, modified or transmitted

in any form or means without the prior written permission of Nokia Siemens Networks. The

documentation has been prepared to be used by professional and properly trained personnel,

and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes

customer comments as part of the process of continuous development and improvement of the

documentation.

The information or statements given in this documentation concerning the suitability, capacity,

or performance of the mentioned hardware or software products are given "as is" and all liability

arising in connection with such hardware or software products shall be defined conclusively and

finally in a separate agreement between Nokia Siemens Networks and the customer. However,

Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions

contained in the document are adequate and free of material errors and omissions. Nokia

Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which

may not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO

EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTA-

TION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDI-

RECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED

TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY

OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION

IN IT.

This documentation and the product it describes are considered protected by copyrights and

other intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark

of Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respectiveowners, and they are mentioned for identification purposes only.

Copyright © Nokia Siemens Networks 2010. All rights reserved

f Important Notice on Product SafetyThis product may present safety risks due to laser, electricity, heat, and other sources

of danger.

Only trained and qualified personnel may install, operate, maintain or otherwise handle

this product and only after having carefully read the safety information applicable to this

product.

The safety information is provided in the Safety Information section in the “Legal, Safety

and Environmental Information” part of this document or documentation set.

The same text in German:

f Wichtiger Hinweis zur ProduktsicherheitVon diesem Produkt können Gefahren durch Laser, Elektrizität, Hitzeentwicklung oder

andere Gefahrenquellen ausgehen.

Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch

geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheits-

anforderungen erfolgen.

Die Sicherheitsanforderungen finden Sie unter „Sicherheitshinweise“ im Teil „Legal,

Safety and Environmental Information“ dieses Dokuments oder dieses Dokumentations-

satzes.



DN998797 3


Id:0900d80580804cd6

Confidential

Table of contentsThis document has 487 pages.

Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

1 List of Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2 Transmission equipment parameters (DX 200 Alarm System). . . . . . . 18

3 Transmission equipment parameters (BTS Alarm System) . . . . . . . . . 23

4 8000 POWER SUPPLY FAULT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

5 8001 TOTAL LOSS OF POWER SUPPLY . . . . . . . . . . . . . . . . . . . . . . 30

6 8002 LOSS OF BACK UP POWER SUPPLY . . . . . . . . . . . . . . . . . . . . 32

7 8003 LOSS OF REMOTE POWER SUPPLY . . . . . . . . . . . . . . . . . . . . 34

8 8004 UNBALANCE IN REMOTE POWER SUPPLY . . . . . . . . . . . . . . . 36

9 8005 INCORRECT RINGING VOLTAGE . . . . . . . . . . . . . . . . . . . . . . . 38

10 8006 FAULT IN CENTRAL BATTERY. . . . . . . . . . . . . . . . . . . . . . . . . . 40

11 8007 FAULT IN CRITERIA VOLTAGE . . . . . . . . . . . . . . . . . . . . . . . . . 42

12 8008 LOW BATTERY VOLTAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

13 8009 FAULT IN CURRENT LOOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

14 8010 SUPPLY UNIT VOLTAGE INCORRECT . . . . . . . . . . . . . . . . . . . 48

15 8011 DISTRIBUTION FUSE FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

16 8012 SIGNALLING VOLTAGE FAULT . . . . . . . . . . . . . . . . . . . . . . . . . 52

17 8013 CHARGER FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

18 8014 AC INPUT VOLTAGE FAILURE. . . . . . . . . . . . . . . . . . . . . . . . . . 56

19 8016 MAIN FUNCTION INHIBITED. . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

20 8017 SIGNAL LOOPED TO TERMINAL . . . . . . . . . . . . . . . . . . . . . . . . 60

21 8018 SIGNAL IS LOOPED TO TRANSMISSION PATH . . . . . . . . . . . . 62

22 8019 FUNCTION INHIBITED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6423 8020 BLOCKED FROM USE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

24 8021 LOOP TO INTERFACE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

25 8022 LOOP TO EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

26 8023 TEST MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

27 8024 LOOP IN EQUIPMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

28 8025 TEST GENERATOR ON. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

29 8026 EXTERNAL TEST MODE ACTIVE. . . . . . . . . . . . . . . . . . . . . . . . 78

30 8027 BLOCKED FROM FAR END . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80



4 DN998797


Id:0900d80580804cd6

Confidential

31 8028 TIMESLOT RESERVED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

32 8032 LOSS OF OUTGOING SIGNAL. . . . . . . . . . . . . . . . . . . . . . . . . . . 84

33 8033 LOSS OF OUTGOING 64K SIGNAL . . . . . . . . . . . . . . . . . . . . . . . 86

34 8034 LOSS OF OUTGOING 2M SIGNAL. . . . . . . . . . . . . . . . . . . . . . . . 88

35 8035 LOSS OF OUTGOING 8M SIGNAL. . . . . . . . . . . . . . . . . . . . . . . . 90

36 8036 LOSS OF OUTGOING 34M SIGNAL. . . . . . . . . . . . . . . . . . . . . . . 92

37 8037 LOSS OF OUTGOING 140M SIGNAL. . . . . . . . . . . . . . . . . . . . . . 94

38 8038 LOSS OF OUTGOING 560M SIGNAL. . . . . . . . . . . . . . . . . . . . . . 96

39 8039 LOSS OF OUTGOING 0.7M SIGNAL . . . . . . . . . . . . . . . . . . . . . . 98

40 8040 NO FREE CHANNEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

41 8042 LOSS OF OUTGOING TRANSMISSION PATH SIGNAL . . . . . . 102

42 8043 INCORRECT OUTGOING SIGNAL LEVEL. . . . . . . . . . . . . . . . . 104

43 8044 HIGH REFLECTED POWER. . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

44 8045 NO OUTGOING SIGNAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

45 8046 NO OUTGOING LINE SIGNAL . . . . . . . . . . . . . . . . . . . . . . . . . . 110

46 8047 PAYLOAD MISMATCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

47 8048 LOSS OF INCOMING SIGNAL . . . . . . . . . . . . . . . . . . . . . . . . . . 114

48 8049 LOSS OF INCOMING 64K SIGNAL . . . . . . . . . . . . . . . . . . . . . . 116

49 8050 LOSS OF INCOMING 2M SIGNAL . . . . . . . . . . . . . . . . . . . . . . . 118

50 8051 LOSS OF INCOMING 8M SIGNAL . . . . . . . . . . . . . . . . . . . . . . . 120

51 8052 LOSS OF INCOMING 34M SIGNAL . . . . . . . . . . . . . . . . . . . . . . 122

52 8053 LOSS OF INCOMING 140M SIGNAL . . . . . . . . . . . . . . . . . . . . . 124

53 8054 LOSS OF INCOMING 560M SIGNAL . . . . . . . . . . . . . . . . . . . . . 126

54 8055 LOSS OF INCOMING 0.7M SIGNAL. . . . . . . . . . . . . . . . . . . . . . 128

55 8056 LOSS OF INCOMING 1.5M SIGNAL. . . . . . . . . . . . . . . . . . . . . . 130

56 8057 LOSS OF POINTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

57 8058 LOSS OF INCOMING TRANSMISSION PATH SIGNAL. . . . . . . 134

58 8059 INCORRECT INCOMING SIGNAL LEVEL . . . . . . . . . . . . . . . . . 136

59 8060 NO INCOMING RADIO SIGNAL . . . . . . . . . . . . . . . . . . . . . . . . . 138

60 8061 LOSS OF INCOMING LINE SIGNAL. . . . . . . . . . . . . . . . . . . . . . 140

61 8062 NO CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

62 8063 NO REDUNDANT CONNECTION. . . . . . . . . . . . . . . . . . . . . . . . 144

63 8064 ALARM SIGNAL (AIS) IS RECEIVED . . . . . . . . . . . . . . . . . . . . . 146



DN998797 5


Id:0900d80580804cd6

Confidential

64 8065 ALARM SIGNAL (AIS 64K) IS RECEIVED. . . . . . . . . . . . . . . . . 148

65 8066 ALARM INDICATION SIGNAL (AIS) RECEIVED. . . . . . . . . . . . 150

66 8067 ALARM SIGNAL (AIS 8M) IS RECEIVED . . . . . . . . . . . . . . . . . 152

67 8068 ALARM SIGNAL (AIS 34M) IS RECEIVED . . . . . . . . . . . . . . . . 154

68 8069 ALARM SIGNAL (AIS 140M) IS RECEIVED . . . . . . . . . . . . . . . 156

69 8070 ALARM SIGNAL (AIS 560M) IS RECEIVED . . . . . . . . . . . . . . . 158

70 8071 ALARM SIGNAL (AIS 0.7M) IS RECEIVED . . . . . . . . . . . . . . . . 160

71 8072 ALARM SIGNAL (AIS 16K) IS RECEIVED. . . . . . . . . . . . . . . . . 162

72 8073 ALARM INDICATION SIGNAL (AIS) RECEIVED. . . . . . . . . . . . 164

73 8074 ALARM INDICATION SIGNAL RECEIVED ON TIMESLOT 16 . 166

74 8075 S ALARM RECEIVED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168

75 8076 GENERAL ALARM IN NETWORK RECEIVED . . . . . . . . . . . . . 170

76 8077 LOOPED SIGNAL RECEIVED . . . . . . . . . . . . . . . . . . . . . . . . . . 172

77 8078 MEASUREMENT SIGNAL RECEIVED . . . . . . . . . . . . . . . . . . . 174

78 8079 TS16 CODE ERROR RECEIVED. . . . . . . . . . . . . . . . . . . . . . . . 176

79 8080 FRAME ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178

80 8081 LOSS OF FRAME ALIGNMENT. . . . . . . . . . . . . . . . . . . . . . . . . 180

81 8082 MULTIFRAME ALIGNMENT LOST . . . . . . . . . . . . . . . . . . . . . . 182

82 8083 LOSS OF FRAME ALIGNMENT OF SUBSYSTEM . . . . . . . . . . 184

83 8084 LOSS OF LINE FRAME ALIGNMENT . . . . . . . . . . . . . . . . . . . . 186

84 8085 LOSS OF RADIO FRAME ALIGNMENT . . . . . . . . . . . . . . . . . . 188

85 8086 LOSS OF CRC MULTIFRAME ALIGNMENT. . . . . . . . . . . . . . . 190

86 8087 LOSS OF OCTET TIMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192

87 8088 END TO END FRAME LOSS . . . . . . . . . . . . . . . . . . . . . . . . . . . 194

88 8089 LOSS OF SIGNALLING FRAME . . . . . . . . . . . . . . . . . . . . . . . . 196

89 8096 EXCESSIVE ERROR RATE. . . . . . . . . . . . . . . . . . . . . . . . . . . . 198

90 8097 BIT ERROR RATIO (BER) > 1E-1 . . . . . . . . . . . . . . . . . . . . . . . 200


92 8099 RECEIVED BIT ERROR RATIO (BER) > 1E-3 . . . . . . . . . . . . . 204







6 DN998797


Id:0900d80580804cd6

Confidential

97 8104 BIT ERROR RATIO (BER) > 1E-8. . . . . . . . . . . . . . . . . . . . . . . . 214

98 8105 BIT ERROR RATIO (BER) > 1E-9. . . . . . . . . . . . . . . . . . . . . . . . 216

99 8106 BIT ERROR RATIO (BER) > 1E-10. . . . . . . . . . . . . . . . . . . . . . . 218



102 8109 FADING IN TRANSMISSION PATH . . . . . . . . . . . . . . . . . . . . . . 224

103 8110 SELECTIVE FADING IN TRANSMISSION PATH. . . . . . . . . . . . 226

104 8111 MODULATION ERROR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228

105 8112 FREQUENCY ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230

106 8113 BUFFER OVERFLOW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232

107 8119 SYNCHRONIZING FAULT IN TRANSMITTER . . . . . . . . . . . . . . 234

108 8120 SYNCHRONIZING FAULT IN RECEIVER . . . . . . . . . . . . . . . . . 236

109 8121 SYNCHRONIZING FAULT IN AUXILIARY CHANNEL . . . . . . . . 238

110 8122 SYNCHRONIZING FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240

111 8123 SYNCHRONIZING FAULT IN CARRIER RECOVERY . . . . . . . . 242

112 8124 SYNCHRONIZATION FAULT IN CLOCK RECOVERY. . . . . . . . 244

113 8125 LOSS OF SYNCHRONIZATION SIGNAL . . . . . . . . . . . . . . . . . . 246

114 8126 UNIT FUNCTION DEGRADED . . . . . . . . . . . . . . . . . . . . . . . . . . 248

115 8127 EQUIPMENT FAULT DETECTED IN AUTOMATIC LOOP TEST250

116 8128 FAULT IN EQUIPMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252

117 8129 FAULT IN CODEC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254

118 8130 FAULT IN MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256

119 8131 INTERNAL BUS FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258

120 8132 FAULT IN SUMMING UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260

121 8133 FAULT IN MUX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262

122 8134 EXCHANGE LINE ALARM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264

123 8135 EQUIPMENT IN RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266

124 8136 AIS OSCILLATOR FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268

125 8137 OSCILLATOR FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270

126 8138 PRESSURE ALARM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272

127 8139 SUBRACK HAS MISSING UNITS. . . . . . . . . . . . . . . . . . . . . . . . 274

128 8140 SUBRACK HAS EXCESSIVE UNITS . . . . . . . . . . . . . . . . . . . . . 276

129 8141 FORCED CONTROL ON. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278



DN998797 7


Id:0900d80580804cd6

Confidential

130 8142 INSTALLATION ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280

131 8143 FAULT IN CHANGE OVER FUNCTION. . . . . . . . . . . . . . . . . . . 282

132 8144 OPERATING ERROR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284

133 8145 TEMPERATURE ALARM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286

134 8146 WIND ALARM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288

135 8147 LOCAL ALARM CANCEL WITHOUT ANY ALARM . . . . . . . . . . 290

136 8148 EQUIPMENT RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292

137 8149 FORCED INDICATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294

138 8150 FAULT IN UNIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296

139 8151 FAULT IN CHANNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298

140 8152 FAULT IN BLOCK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300

141 8153 FAULT IN TRANSMITTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302

142 8154 FAULT IN RECEIVER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304

143 8155 LASER BIAS OUT OF RANGE. . . . . . . . . . . . . . . . . . . . . . . . . . 306

144 8156 LASER POWER OUT OF RANGE . . . . . . . . . . . . . . . . . . . . . . . 308

145 8157 LASER TEMPERATURE OUT OF RANGE . . . . . . . . . . . . . . . . 310

146 8158 FORCED LASER CUT OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312

147 8159 RUN DIAGNOSTICS TEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314

148 8160 INTERFACE UNIT FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316

149 8161 CONNECTED TO REDUNDANT SYSTEM . . . . . . . . . . . . . . . . 318

150 8162 DATABASE FULL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320

151 8163 REDUNDANT CONNECTION IN USE . . . . . . . . . . . . . . . . . . . . 322

152 8164 LINE CABLE FAULT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324

153 8165 REAL TIME LOST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326

154 8166 E1 CONVERTER RESET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328

155 8167 E1 CONVERTER FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330

156 8168 EQUIPMENT DOOR OPEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332

157 8169 EXTENDED FAULT CODE IN USE . . . . . . . . . . . . . . . . . . . . . . 334

158 8172 YELLOW ALARM OCCURRED . . . . . . . . . . . . . . . . . . . . . . . . . 336

159 8173 FAR-END ALARM 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338

160 8174 FAR-END ALARM 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340

161 8175 FAR-END ALARM 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342

162 8176 FAR-END ALARM RECEIVED . . . . . . . . . . . . . . . . . . . . . . . . . . 344



8 DN998797


Id:0900d80580804cd6

Confidential

163 8178 MULTIFRAME ALARM FROM FAR-END . . . . . . . . . . . . . . . . . . 346

164 8179 FAR-END ALARM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 348

165 8180 ALARM FROM FAR-END SUBSYSTEM. . . . . . . . . . . . . . . . . . . 350

166 8181 FAR-END SENDING FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352

167 8182 FAULT IN FAR-END RECEIVING . . . . . . . . . . . . . . . . . . . . . . . . 354

168 8183 FAR-END SYNCHRONIZATION ALARM . . . . . . . . . . . . . . . . . . 356

169 8184 REAL TIME UPDATED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358

170 8185 CONNECTION OR SETTINGS HAVE CHANGED . . . . . . . . . . . 360

171 8186 CONFIGURATION ERROR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362

172 8190 CUSTOMER SPECIFIC FAULT CODE 1 . . . . . . . . . . . . . . . . . . 364





177 8195 V5 PROTOCOL ALARM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374

178 8200 LOSS OF PRIMARY SUPERVISION CONNECTION . . . . . . . . . 376

179 8201 LOSS OF SECONDARY SUPERVISION CONNECTION. . . . . . 378

180 8202 LOSS OF SUPERVISION CONNECTION. . . . . . . . . . . . . . . . . . 380

181 8203 LOSS OF SUPERVISION BUS . . . . . . . . . . . . . . . . . . . . . . . . . . 382

182 8206 CONGESTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384

183 8207 CALIBRATION EXPIRED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386

184 8213 REMOTE DEFECT INDICATION (RDI). . . . . . . . . . . . . . . . . . . . 388

185 8214 SIGNAL DEGRADED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390

186 8215 TRACE IDENTIFIER MISMATCH . . . . . . . . . . . . . . . . . . . . . . . . 392

187 8216 UNEQUIPPED SIGNAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394

188 8221 VERSION MISMATCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396

189 8222 CORRUPT DATA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398

190 8223 PROTECTION SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400

191 8230 THRESHOLD CROSSED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402

192 8240 ACTIVE ALARM POINT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404

193 8241 UPPER ALARM LIMIT EXCEEDED . . . . . . . . . . . . . . . . . . . . . . 406

194 8242 LOWER ALARM LIMIT EXCEEDED . . . . . . . . . . . . . . . . . . . . . . 408

195 8250 INVALID TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410



DN998797 9


Id:0900d80580804cd6

Confidential

196 8254 OPERATOR DISABLED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412

197 8256 15 MIN G826 ES THRESHOLD CROSSED. . . . . . . . . . . . . . . . 414

198 8257 15 MIN G826 SES THRESHOLD CROSSED . . . . . . . . . . . . . . 416

199 8258 15 MIN G826 BBE THRESHOLD CROSSED . . . . . . . . . . . . . . 418

200 8259 24 H G826 ES THRESHOLD CROSSED. . . . . . . . . . . . . . . . . . 420

201 8260 24 H G826 SES THRESHOLD CROSSED . . . . . . . . . . . . . . . . 422

202 8261 24 H G826 BBE THRESHOLD CROSSED . . . . . . . . . . . . . . . . 424

203 8262 STATISTIC UNAVAILABILITY . . . . . . . . . . . . . . . . . . . . . . . . . . 426

204 8263 STATISTIC RESET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 428

205 8264 15 MIN T/RLTS THRESHOLD CROSSED. . . . . . . . . . . . . . . . . 430

206 8265 24 H T/RLTS THRESHOLD CROSSED. . . . . . . . . . . . . . . . . . . 432

207 8266 LICENCE KEY NOT VALID . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434

208 8267 LICENCE EXPIRED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436

209 8268 LICENCE WILL EXPIRE IN THE NEAR FUTURE . . . . . . . . . . . 438

210 8269 LICENCE FOR FEATURE IS NOT AVAILABLE. . . . . . . . . . . . . 440

211 8270 LICENCE FOR FEATURE HAS BEEN ACTIVATED . . . . . . . . . 442

212 8271 LICENCE FOR FEATURE HAS BEEN DEACTIVATED. . . . . . . 444

213 8272 POSITION NOT LOCKED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 446

214 8273 LICENCE FOR 2G FLEXI ABIS OVER IP/ETHERNET IS NOT

AVAILABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 448

215 8274 LICENCE FOR 2G FLEXI ADDITIONAL 2 E1/T1 IS NOT AVAILABLE

450

216 8275 LICENCE FOR 2G FLEXI ABIS TRS GROOMING IS NOT AVAIL-

ABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 452

217 8276 LICENCE FOR 2G FLEXI TRS LOOP PROTECTION IS NOT AVAIL-

ABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454

218 8277 ETHERNET PHYSICAL LINK LAYER LOST . . . . . . . . . . . . . . . 456

219 8278 PSEUDOWIRE DOWN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458

220 8279 PSEUDOWIRE PERFORMANCE DEGRADED. . . . . . . . . . . . . 460

221 8280 PSEUDOWIRE REMOTE PACKET LOSS. . . . . . . . . . . . . . . . . 462

222 8281 FAULT IN OPTICAL INTERFACE (SFP) . . . . . . . . . . . . . . . . . . 464

223 8282 PSEUDOWIRE TUNNEL DOWN . . . . . . . . . . . . . . . . . . . . . . . . 466

224 8283 LICENCE FOR IP SECURITY IS NOT AVAILABLE. . . . . . . . . . 468

225 8284 TRAFFIC SHAPING MISCONFIGURATION . . . . . . . . . . . . . . . 470

226 8285 LICENCE FOR TIMING OVER PACKET IS NOT AVAILABLE . 472



10 DN998797


Id:0900d80580804cd6

Confidential

227 8286 LICENCE FOR SYNCHRONOUS ETHERNET IS NOT AVAILABLE

474

228 8287 CLOCK RECOVERY IN PROGRESS . . . . . . . . . . . . . . . . . . . . . 476

229 8288 FAULT IN CONNECTION TO CLOCK MASTER . . . . . . . . . . . . 478

230 8289 SSM HAS LOST TRACEABILITY TO PRC CLOCK SOURCE . . 480

231 8290 LICENCE FOR PACKET TRS E1/T1 IS NOT AVAILABLE . . . . . 482

232 8291 PMTU BTS TO BSC LESS THAN CONFIGRUED MTU . . . . . . . 484

233 8292 PMTU BTS TO SECURITY GATEWAY LESS THAN CONFIGURED

MTU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 486



DN998797 11

Transmission Equipment Alarms (8000-8999) Summary of changes

Id:0900d80580804c95

Confidential

Summary of changesChanges between document issues are cumulative. Therefore, the latest document

issue contains all changes made to previous issues.

Changes made between issues 8-1 and 8-0

Alarms 8288 and 8289 have been updated. Notes added to meaning of alarm sections.


New alarms

Modified alarms


The names of the features BSS30305: 2G Flexi Abis over IP/Ethernet, BSS30280: 2GFlexi TRS Loop Protection, BSS21129: Flexi EDGE Abis TRS Grooming, and

BSS30285: 2G Flexi Additional 2 E1,T1 IF have been modified.


Modified alarms

The Flexi EDGE BTS specific instructions of the following alarms have been updated:

– 8273 LICENCE FOR FLEXIEDGE ABIS OVER IP/ETHERNET IS NOT AVAILABLE

– 8274 LICENCE FOR FLEXIEDGE ADDITIONAL 2 E1/T1 IS NOT AVAILABLE

– 8275 LICENCE FOR FLEXIEDGE TRS ABIS GROOMING IS NOT AVAILABLE

– 8276 LICENCE FOR FLEXIEDGE TRS LOOP PROTECTION IS NOT AVAILABLE

8283 8286 8289 8292

8284 8287 8290

8285 8288 8291

8099 8274 8277 8281

8112 8275 8278 8282

8273 8276 8280



12 DN998797


Id:0900d80580804c95

Confidential

List of Alarms

1 List of Alarms8000 POWER SUPPLY FAULT

8001 TOTAL LOSS OF POWER SUPPLY8002 LOSS OF BACK UP POWER SUPPLY

8003 LOSS OF REMOTE POWER SUPPLY

8004 UNBALANCE IN REMOTE POWER SUPPLY

8005 INCORRECT RINGING VOLTAGE

8006 FAULT IN CENTRAL BATTERY

8007 FAULT IN CRITERIA VOLTAGE

8008 LOW BATTERY VOLTAGE

8009 FAULT IN CURRENT LOOP

8010 SUPPLY UNIT VOLTAGE INCORRECT

8011 DISTRIBUTION FUSE FAULT

8012 SIGNALLING VOLTAGE FAULT

8013 CHARGER FAULT

8014 AC INPUT VOLTAGE FAILURE

8016 MAIN FUNCTION INHIBITED

8017 SIGNAL LOOPED TO TERMINAL

8018 SIGNAL IS LOOPED TO TRANSMISSION PATH

8019 FUNCTION INHIBITED

8020 BLOCKED FROM USE

8021 LOOP TO INTERFACE

8022 LOOP TO EQUIPMENT

8023 TEST MODE

8024 LOOP IN EQUIPMENT

8025 TEST GENERATOR ON

8026 EXTERNAL TEST MODE ACTIVE

8027 BLOCKED FROM FAR END

8028 TIMESLOT RESERVED

8032 LOSS OF OUTGOING SIGNAL

8033 LOSS OF OUTGOING 64K SIGNAL

8034 LOSS OF OUTGOING 2M SIGNAL





8039 LOSS OF OUTGOING 0.7M SIGNAL

8040 NO FREE CHANNEL



DN998797 13

Transmission Equipment Alarms (8000-8999) List of Alarms

Id:0900d80580804c95

Confidential

8042 LOSS OF OUTGOING TRANSMISSION PATH SIGNAL

8043 INCORRECT OUTGOING SIGNAL LEVEL

8044 HIGH REFLECTED POWER

8045 NO OUTGOING SIGNAL

8046 NO OUTGOING LINE SIGNAL

8047 PAYLOAD MISMATCH

8048 LOSS OF INCOMING SIGNAL

8049 LOSS OF INCOMING 64K SIGNAL

8050 LOSS OF INCOMING 2M SIGNAL





8055 LOSS OF INCOMING 0.7M SIGNAL


8057 LOSS OF POINTER

8058 LOSS OF INCOMING TRANSMISSION PATH SIGNAL

8059 INCORRECT INCOMING SIGNAL LEVEL

8060 NO INCOMING RADIO SIGNAL

8061 LOSS OF INCOMING LINE SIGNAL

8062 NO CONNECTION8063 NO REDUNDANT CONNECTION

8064 ALARM SIGNAL (AIS) IS RECEIVED

8065 ALARM SIGNAL (AIS 64K) IS RECEIVED

8066 ALARM INDICATION SIGNAL (AIS) RECEIVED

8067 ALARM SIGNAL (AIS 8M) IS RECEIVED




8071 ALARM SIGNAL (AIS 0.7M) IS RECEIVED



8074 ALARM INDICATION SIGNAL RECEIVED ON TIMESLOT 16

8075 S ALARM RECEIVED

8076 GENERAL ALARM IN NETWORK RECEIVED

8077 LOOPED SIGNAL RECEIVED

8078 MEASUREMENT SIGNAL RECEIVED

8079 TS16 CODE ERROR RECEIVED

8080 FRAME ERROR



14 DN998797


Id:0900d80580804c95

Confidential

List of Alarms

8081 LOSS OF FRAME ALIGNMENT

8082 MULTIFRAME ALIGNMENT LOST

8083 LOSS OF FRAME ALIGNMENT OF SUBSYSTEM

8084 LOSS OF LINE FRAME ALIGNMENT

8085 LOSS OF RADIO FRAME ALIGNMENT

8086 LOSS OF CRC MULTIFRAME ALIGNMENT

8087 LOSS OF OCTET TIMING

8088 END TO END FRAME LOSS

8089 LOSS OF SIGNALLING FRAME

8096 EXCESSIVE ERROR RATE

8097 BIT ERROR RATIO (BER) > 1E-1


8099 RECEIVED BIT ERROR RATIO (BER) > 1E-3








8107 BIT ERROR RATIO (BER) > 1E-118108 BIT ERROR RATIO (BER) > 1E-12

8109 FADING IN TRANSMISSION PATH

8110 SELECTIVE FADING IN TRANSMISSION PATH

8111 MODULATION ERROR

8112 FREQUENCY ERROR

8113 BUFFER OVERFLOW

8119 SYNCHRONIZING FAULT IN TRANSMITTER

8120 SYNCHRONIZING FAULT IN RECEIVER

8121 SYNCHRONIZING FAULT IN AUXILIARY CHANNEL

8122 SYNCHRONIZING FAULT

8123 SYNCHRONIZING FAULT IN CARRIER RECOVERY

8124 SYNCHRONIZATION FAULT IN CLOCK RECOVERY

8125 LOSS OF SYNCHRONIZATION SIGNAL

8126 UNIT FUNCTION DEGRADED

8127 EQUIPMENT FAULT DETECTED IN AUTOMATIC LOOP TEST

8128 FAULT IN EQUIPMENT

8129 FAULT IN CODEC

8130 FAULT IN MEMORY



DN998797 15


Id:0900d80580804c95

Confidential

8131 INTERNAL BUS FAULT

8132 FAULT IN SUMMING UNIT

8133 FAULT IN MUX

8134 EXCHANGE LINE ALARM

8135 EQUIPMENT IN RESET

8136 AIS OSCILLATOR FAULT

8137 OSCILLATOR FAULT

8138 PRESSURE ALARM

8139 SUBRACK HAS MISSING UNITS

8140 SUBRACK HAS EXCESSIVE UNITS

8141 FORCED CONTROL ON

8142 INSTALLATION ERROR

8143 FAULT IN CHANGE OVER FUNCTION

8144 OPERATING ERROR

8145 TEMPERATURE ALARM

8146 WIND ALARM

8147 LOCAL ALARM CANCEL WITHOUT ANY ALARM

8148 EQUIPMENT RESET

8149 FORCED INDICATION

8150 FAULT IN UNIT

8151 FAULT IN CHANNEL8152 FAULT IN BLOCK

8153 FAULT IN TRANSMITTER

8154 FAULT IN RECEIVER

8155 LASER BIAS OUT OF RANGE

8156 LASER POWER OUT OF RANGE

8157 LASER TEMPERATURE OUT OF RANGE

8158 FORCED LASER CUT OFF

8159 RUN DIAGNOSTICS TEST

8160 INTERFACE UNIT FAULT

8161 CONNECTED TO REDUNDANT SYSTEM

8162 DATABASE FULL

8163 REDUNDANT CONNECTION IN USE

8164 LINE CABLE FAULT

8165 REAL TIME LOST

8166 E1 CONVERTER RESET

8167 E1 CONVERTER FAULT

8168 EQUIPMENT DOOR OPEN

8169 EXTENDED FAULT CODE IN USE



16 DN998797


Id:0900d80580804c95

Confidential

List of Alarms

8172 YELLOW ALARM OCCURRED

8173 FAR-END ALARM 4



8176 FAR-END ALARM RECEIVED

8178 MULTIFRAME ALARM FROM FAR-END

8179 FAR-END ALARM

8180 ALARM FROM FAR-END SUBSYSTEM

8181 FAR-END SENDING FAULT

8182 FAULT IN FAR-END RECEIVING

8183 FAR-END SYNCHRONIZATION ALARM

8184 REAL TIME UPDATED

8185 CONNECTION OR SETTINGS HAVE CHANGED

8186 CONFIGURATION ERROR

8190 CUSTOMER SPECIFIC FAULT CODE 1





8195 V5 PROTOCOL ALARM

8200 LOSS OF PRIMARY SUPERVISION CONNECTION8201 LOSS OF SECONDARY SUPERVISION CONNECTION

8202 LOSS OF SUPERVISION CONNECTION

8203 LOSS OF SUPERVISION BUS

8206 CONGESTION

8207 CALIBRATION EXPIRED

8213 REMOTE DEFECT INDICATION (RDI)

8214 SIGNAL DEGRADED

8215 TRACE IDENTIFIER MISMATCH

8216 UNEQUIPPED SIGNAL

8221 VERSION MISMATCH

8222 CORRUPT DATA

8223 PROTECTION SWITCH

8230 THRESHOLD CROSSED

8240 ACTIVE ALARM POINT

8241 UPPER ALARM LIMIT EXCEEDED

8242 LOWER ALARM LIMIT EXCEEDED

8250 INVALID TIME

8254 OPERATOR DISABLED



DN998797 17


Id:0900d80580804c95

Confidential

8256 15 MIN G826 ES THRESHOLD CROSSED

8257 15 MIN G826 SES THRESHOLD CROSSED

8258 15 MIN G826 BBE THRESHOLD CROSSED

8259 24 H G826 ES THRESHOLD CROSSED

8260 24 H G826 SES THRESHOLD CROSSED

8261 24 H G826 BBE THRESHOLD CROSSED

8262 STATISTIC UNAVAILABILITY

8263 STATISTIC RESET

8264 15 MIN T/RLTS THRESHOLD CROSSED

8265 24 H T/RLTS THRESHOLD CROSSED

8266 LICENCE KEY NOT VALID

8267 LICENCE EXPIRED

8268 LICENCE WILL EXPIRE IN THE NEAR FUTURE

8269 LICENCE FOR FEATURE IS NOT AVAILABLE

8270 LICENCE FOR FEATURE HAS BEEN ACTIVATED

8271 LICENCE FOR FEATURE HAS BEEN DEACTIVATED

8272 POSITION NOT LOCKED

8273 LICENCE FOR 2G FLEXI ABIS OVER IP/ETHERNET IS NOT AVAIL-

ABLE

8274 LICENCE FOR 2G FLEXI ADDITIONAL 2 E1/T1 IS NOT AVAILABLE

8275 LICENCE FOR 2G FLEXI ABIS TRS GROOMING IS NOT AVAILABLE

8276 LICENCE FOR 2G FLEXI TRS LOOP PROTECTION IS NOT AVAIL-

ABLE

8277 ETHERNET PHYSICAL LINK LAYER LOST

8278 PSEUDOWIRE DOWN

8279 PSEUDOWIRE PERFORMANCE DEGRADED

8280 PSEUDOWIRE REMOTE PACKET LOSS

8281 FAULT IN OPTICAL INTERFACE (SFP)

8282 PSEUDOWIRE TUNNEL DOWN

8283 LICENCE FOR IP SECURITY IS NOT AVAILABLE

8284 TRAFFIC SHAPING MISCONFIGURATION

8285 LICENCE FOR TIMING OVER PACKET IS NOT AVAILABLE

8286 LICENCE FOR SYNCHRONOUS ETHERNET IS NOT AVAILABLE

8287 CLOCK RECOVERY IN PROGRESS

8288 FAULT IN CONNECTION TO CLOCK MASTER

8289 SSM HAS LOST TRACEABILITY TO PRC CLOCK SOURCE

8290 LICENCE FOR PACKET TRS E1/T1 IS NOT AVAILABLE

8291 PMTU BTS TO BSC LESS THAN CONFIGRUED MTU

8292 PMTU BTS TO SECURITY GATEWAY LESS THAN CONFIGUREDMTU



18 DN998797


Id:0900d80580804c95

Confidential

Transmission equipment parameters (DX 200 AlarmSystem)

2 Transmission equipment parameters (DX

200 Alarm System)

ALARM CLS OUT IDL IDD CDL ALV

8000 *** ALARM 1 00:00 00:00 00:00 -

8001 *** ALARM 1 00:00 00:10 00:10 -

8002 *** ALARM 1 00:00 00:10 00:10 -

8003 *** ALARM 1 00:00 00:10 00:10 -

8004 *** ALARM 1 00:00 00:10 00:10 -

8005 *** ALARM 1 00:00 00:10 00:10 -

8006 *** ALARM 1 00:00 00:10 00:10 -

8007 *** ALARM 1 00:00 00:10 00:10 -

8008 *** ALARM 1 00:00 00:10 00:10 -

8009 *** ALARM 1 00:00 00:10 00:10 -

8010 *** ALARM 1 00:00 00:10 00:10 -8011 *** ALARM 1 00:00 00:10 00:10 -

8012 *** ALARM 1 00:00 00:10 00:10 -

8013 ** ALARM 5 00:00 00:10 00:10 -

8014 NOTICE NONE 00:00 00:00 00:00 00:00:15

8016 *** ALARM 1 00:00 00:10 00:10 -

8017 *** ALARM 1 00:00 00:10 00:10 -

8018 *** ALARM 1 00:00 00:10 00:10 -

8019 *** ALARM 1 00:00 00:10 00:10 -

8020 ** ALARM 5 00:00 00:10 00:10 -

8021 ** ALARM 5 00:00 00:10 00:10 -

8022 ** ALARM 5 00:00 00:10 00:10 -

8023 ** ALARM 5 00:00 00:10 00:10 -

8024 *** ALARM 1 00:00 00:10 00:10 -

8025 ** ALARM 5 00:00 00:10 00:10 -

8026 ** ALARM 5 00:00 00:10 00:10 -

8027 ** ALARM 5 00:00 00:10 00:10 -

8028 ** ALARM 5 00:00 00:10 00:10 -

8032 *** ALARM 1 00:00 00:10 00:10 -

8033 *** ALARM 1 00:00 00:10 00:10 -

8034 *** ALARM 1 00:00 00:10 00:10 -

8035 *** ALARM 1 00:00 00:10 00:10 -

8036 *** ALARM 1 00:00 00:10 00:10 -

8037 *** ALARM 1 00:00 00:10 00:10 -8038 *** ALARM 1 00:00 00:10 00:10 -

8039 *** ALARM 1 00:00 00:10 00:10 -

8040 DISTUR NONE 00:00 00:00 00:00 00:00:15

8042 *** ALARM 1 00:00 00:10 00:10 -

8043 *** ALARM 1 00:00 00:10 00:10 -

8044 *** ALARM 1 00:00 00:10 00:10 -

8045 *** ALARM 1 00:00 00:10 00:10 -

8046 *** ALARM 1 00:00 00:10 00:10 -

8047 *** ALARM 1 00:00 00:10 00:10 -

8048 *** ALARM 1 00:00 00:10 00:10 -

8049 *** ALARM 1 00:00 00:10 00:10 -

8050 *** ALARM 1 00:00 00:10 00:10 -



DN998797 19

Transmission Equipment Alarms (8000-8999) Transmission equipment parameters (DX 200 AlarmSystem)

Id:0900d80580804c95

Confidential

8051 *** ALARM 1 00:00 00:10 00:10 -

8052 *** ALARM 1 00:00 00:10 00:10 -

8053 *** ALARM 1 00:00 00:10 00:10 -

8054 *** ALARM 1 00:00 00:10 00:10 -

8055 *** ALARM 1 00:00 00:10 00:10 -

8056 *** ALARM 1 00:00 00:10 00:10 -

8057 *** ALARM 1 00:00 00:10 00:10 -

8058 *** ALARM 1 00:00 00:10 00:10 -

8059 *** ALARM 1 00:00 00:10 00:10 -

8060 *** ALARM 1 00:00 00:10 00:10 -

8061 *** ALARM 1 00:00 00:10 00:10 -

8062 *** ALARM 1 00:00 00:10 00:10 -

8063 *** ALARM 1 00:00 00:10 00:10 -

8064 ** ALARM 5 00:00 00:10 00:10 -

8065 ** ALARM 5 00:00 00:10 00:10 -

8066 ** ALARM 5 00:00 00:10 00:10 -8067 ** ALARM 5 00:00 00:10 00:10 -

8068 ** ALARM 5 00:00 00:10 00:10 -

8069 ** ALARM 5 00:00 00:10 00:10 -

8070 ** ALARM 5 00:00 00:10 00:10 -

8071 ** ALARM 5 00:00 00:10 00:10 -

8072 ** ALARM 5 00:00 00:10 00:10 -

8073 ** ALARM 5 00:00 00:10 00:10 -

8074 ** ALARM 5 00:00 00:10 00:10 -

8075 ** ALARM 5 00:00 00:10 00:10 -

8076 ** ALARM 5 00:00 00:10 00:10 -

8077 ** ALARM 5 00:00 00:10 00:10 -

8078 ** ALARM 5 00:00 00:10 00:10 -

8079 ** ALARM 5 00:00 00:10 00:10 -

8080 *** ALARM 1 00:00 00:10 00:10 -

8081 *** ALARM 1 00:00 00:10 00:10 -

8082 *** ALARM 1 00:00 00:10 00:10 -

8083 *** ALARM 1 00:00 00:10 00:10 -

8084 *** ALARM 1 00:00 00:10 00:10 -

8085 *** ALARM 1 00:00 00:10 00:10 -

8086 *** ALARM 1 00:00 00:10 00:10 -

8087 *** ALARM 1 00:00 00:10 00:10 -

8088 *** ALARM 1 00:00 00:10 00:10 -

8089 *** ALARM 1 00:00 00:10 00:10 -

8096 *** ALARM 1 00:00 00:10 00:10 -

8097 *** ALARM 1 00:00 00:10 00:10 -

8098 *** ALARM 1 00:00 00:10 00:10 -

8099 *** ALARM 1 00:00 00:15 00:10 -

8100 ** ALARM 5 00:00 00:10 00:10 -

8101 ** ALARM 5 00:00 00:10 00:10 -

8102 ** ALARM 5 00:00 00:30 00:40 -

8103 * ALARM NONE 00:00 00:10 00:10 -

8104 * ALARM NONE 00:00 00:10 00:10 -

8105 * ALARM NONE 00:00 00:10 00:10 -

8106 * ALARM NONE 00:00 00:10 00:10 -8107 * ALARM NONE 00:00 00:10 00:10 -



20 DN998797


Id:0900d80580804c95

Confidential


8108 * ALARM NONE 00:00 00:10 00:10 -

8109 ** ALARM 5 00:00 00:10 00:10 -

8110 ** ALARM 5 00:00 00:10 00:10 -

8111 *** ALARM 1 00:00 00:10 00:10 -

8112 * ALARM NONE 00:00 00:10 00:10 -

8113 * ALARM NONE 00:00 00:10 00:10 -

8119 ** ALARM 5 00:00 00:10 00:10 -

8120 ** ALARM 5 00:00 00:10 00:10 -

8121 ** ALARM 5 00:00 00:10 00:10 -

8122 ** ALARM 5 00:00 00:10 00:10 -

8123 ** ALARM 5 00:00 00:10 00:10 -

8124 ** ALARM 5 00:00 00:10 00:10 -

8125 *** ALARM 1 00:00 00:10 00:10 -

8126 ** ALARM 5 00:00 00:10 00:10 -

8127 ** ALARM 5 00:00 00:10 00:10 -

8128 ** ALARM 5 00:00 00:10 00:10 -8129 ** ALARM 5 00:00 00:10 00:10 -

8130 ** ALARM 5 00:00 00:10 00:10 -

8131 ** ALARM 5 00:00 00:10 00:10 -

8132 ** ALARM 5 00:00 00:10 00:10 -

8133 ** ALARM 5 00:00 00:10 00:10 -

8134 ** ALARM 5 00:00 00:10 00:10 -

8135 ** ALARM 5 00:00 00:10 00:10 -

8136 ** ALARM 5 00:00 00:10 00:10 -

8137 ** ALARM 5 00:00 00:10 00:10 -

8138 ** ALARM 5 00:00 00:10 00:10 -

8139 *** ALARM 1 00:00 00:10 00:10 -

8140 ** ALARM 5 00:00 00:10 00:10 -

8141 *** ALARM 1 00:00 00:10 00:10 -

8142 *** ALARM 1 00:00 00:10 00:10 -

8143 *** ALARM 1 00:00 00:10 00:10 -

8144 *** ALARM 1 00:00 00:10 00:10 -

8145 ** ALARM 5 00:00 00:10 00:10 -

8146 ** ALARM 5 00:00 00:10 00:10 -

8147 NOTICE NONE 00:00 00:00 00:00 00:00:15

8148 NOTICE NONE 00:00 00:00 00:00 00:00:15

8149 NOTICE NONE 00:00 00:00 00:00 00:00:15

8150 *** ALARM 1 00:00 00:10 00:10 -

8151 *** ALARM 1 00:00 00:10 00:10 -

8152 *** ALARM 1 00:00 00:10 00:10 -

8153 *** ALARM 1 00:00 00:10 00:10 -

8154 *** ALARM 1 00:00 00:10 00:10 -

8155 *** ALARM 1 00:00 00:10 00:10 -

8156 *** ALARM 1 00:00 00:10 00:10 -

8157 *** ALARM 1 00:00 00:10 00:10 -

8158 *** ALARM 1 00:00 00:10 00:10 -

8159 *** ALARM 1 00:00 00:10 00:10 -

8160 *** ALARM 1 00:00 00:10 00:10 -

8161 ** ALARM 5 00:00 00:10 00:10 -

8162 NOTICE NONE 00:00 00:00 00:00 00:00:158163 ** ALARM 5 00:00 00:10 00:10 -



DN998797 21

Transmission Equipment Alarms (8000-8999) Transmission equipment parameters (DX 200 AlarmSystem)

Id:0900d80580804c95

Confidential

8164 *** ALARM 1 00:00 00:10 00:10 -

8165 ** ALARM 5 00:00 00:10 00:10 -

8166 ** ALARM 5 00:00 00:10 00:10 -

8167 *** ALARM 1 00:00 00:10 00:10 -

8168 * ALARM NONE 00:00 00:10 00:10 -

8169 * ALARM NONE 00:00 00:10 00:10 -

8172 ** ALARM 5 00:00 00:10 00:10 -

8173 DISTUR NONE 00:00 00:00 00:00 00:00:15

8174 * ALARM NONE 00:00 00:10 00:10 -

8175 ** ALARM 5 00:00 00:10 00:10 -

8176 *** ALARM 1 00:00 00:10 00:10 -

8178 ** ALARM 5 00:00 00:10 00:10 -

8179 ** ALARM 5 00:00 00:10 00:10 -

8180 ** ALARM 5 00:00 00:10 00:10 -

8181 ** ALARM 5 00:00 00:10 00:10 -

8182 ** ALARM 5 00:00 00:10 00:10 -8183 ** ALARM 5 00:00 00:10 00:10 -

8184 NOTICE NONE 00:00 00:00 00:00 00:00:15

8185 DISTUR NONE 00:00 00:00 00:00 00:00:15

8186 * ALARM NONE 00:00 00:00 00:00 -

8190 * ALARM NONE 00:00 00:00 00:00 -

8191 * ALARM NONE 00:00 00:00 00:00 -

8192 * ALARM NONE 00:00 00:00 00:00 -

8193 ** ALARM 5 00:00 00:00 00:00 -

8194 ** ALARM 5 00:00 00:00 00:00 -

8195 *** ALARM 1 00:00 00:00 00:00 -

8200 ** ALARM 5 00:00 00:00 00:00 -

8201 ** ALARM 5 00:00 00:00 00:00 -

8202 *** ALARM 1 00:00 00:00 00:00 -

8203 *** ALARM 1 00:00 00:00 00:00 -

8206 DISTUR NONE 00:00 00:00 00:00 00:00:15

8207 DISTUR NONE 00:00 00:00 00:00 00:00:15

8213 ** ALARM 5 00:00 00:00 00:00 -

8214 ** ALARM 5 00:00 00:00 00:00 -

8215 *** ALARM 1 00:00 00:00 00:00 -

8216 *** ALARM 1 00:00 00:00 00:00 -

8221 *** ALARM 1 00:00 00:00 00:00 -

8222 *** ALARM 1 00:00 00:00 00:00 -

8223 DISTUR NONE 00:00 00:00 00:00 00:00:15

8230 NOTICE NONE 00:00 00:00 00:00 00:00:15

8240 ** ALARM 5 00:00 00:00 00:00 -

8241 *** ALARM 1 00:00 00:00 00:00 -

8242 * ALARM NONE 00:00 00:00 00:00 -

8250 * ALARM NONE 00:00 00:00 00:00 -

8254 NOTICE NONE 00:00 00:00 00:00 00:00:15

8256 * ALARM NONE 00:00 00:00 00:00 -

8257 ** ALARM 5 00:00 00:00 00:00 -

8258 * ALARM NONE 00:00 00:00 00:00 -

8259 NOTICE NONE 00:00 00:00 00:00 00:00:15

8260 NOTICE NONE 00:00 00:00 00:00 00:00:158261 NOTICE NONE 00:00 00:00 00:00 00:00:15



22 DN998797


Id:0900d80580804c95

Confidential


8262 *** ALARM 1 00:00 00:00 00:00 -

8263 NOTICE NONE 00:00 00:00 00:00 00:00:15

8264 ** ALARM 5 00:00 00:00 00:00 -

8265 NOTICE NONE 00:00 00:00 00:00 00:00:15

8266 *** ALARM 1 00:00 00:00 00:00 -

8267 *** ALARM 1 00:00 00:00 00:00 -

8268 ** ALARM 5 00:00 00:00 00:00 -

8269 *** ALARM 1 00:00 00:00 00:00 -

8270 NOTICE NONE 00:00 00:00 00:00 00:00:15

8271 NOTICE NONE 00:00 00:00 00:00 00:00:15

8272 * ALARM NONE 00:10 00:10 00:10 -

8273 *** ALARM 1 00:10 00:10 00:10 -

8274 *** ALARM 1 00:10 00:10 00:10 -

8275 * ALARM NONE 00:10 00:10 00:10 -

8276 * ALARM NONE 00:10 00:10 00:10 -

8277 *** ALARM 1 00:10 00:10 00:10 -8278 *** ALARM 1 00:10 00:10 00:10 -

8279 ** ALARM 5 00:10 00:10 00:10 -

8280 ** ALARM 5 00:10 00:10 00:10 -

8281 *** ALARM 1 00:10 00:10 00:10 -

8282 ** ALARM 5 00:10 00:10 00:10 -

8283 *** ALARM 1 00:10 00:10 00:10 -

8284 ** ALARM 5 00:10 00:10 00:10 -

8285 ** ALARM 5 00:10 00:10 00:10 -

8286 *** ALARM 1 00:10 00:10 00:10 -

8287 * ALARM NONE 00:10 00:10 00:10 -

8288 ** ALARM 5 00:10 00:10 00:10 -

8289 ** ALARM 5 00:10 00:10 00:10 -

8290 ** ALARM 5 00:10 00:10 00:10 -

8291 ** ALARM 5 00:10 00:10 00:10 -

8292 * ALARM NONE 00:10 00:10 00:10 -



DN998797 23

Transmission Equipment Alarms (8000-8999) Transmission equipment parameters (BTS Alarm Sys-tem)

Id:0900d80580804c95

Confidential

3 Transmission equipment parameters (BTS

Alarm System)

NUMBER CLASS RECOVERY PRINTING OMC UPD. IDL CDL STATE

8000 *** ON OFF ON 10 10 UNBLOCKED










8010 *** ON OFF ON 10 10 UNBLOCKED8011 *** ON OFF ON 10 10 UNBLOCKED


8013 ** ON OFF ON 10 10 UNBLOCKED

8014 ON OFF ON 10 10 UNBLOCKED



















8037 *** ON OFF ON 10 10 UNBLOCKED8038 *** ON OFF ON 10 10 UNBLOCKED














24 DN998797


Id:0900d80580804c95

Confidential

Transmission equipment parameters (BTS Alarm Sys-tem)
















8066 ** ON OFF ON 10 10 UNBLOCKED8067 ** ON OFF ON 10 10 UNBLOCKED






























8103 * ON OFF ON 10 10 UNBLOCKED



8106 * ON OFF ON 10 10 UNBLOCKED8107 * ON OFF ON 10 10 UNBLOCKED



DN998797 25


Id:0900d80580804c95

Confidential

















































8162 ON OFF ON 10 10 UNBLOCKED8163 ** ON OFF ON 10 10 UNBLOCKED



26 DN998797


Id:0900d80580804c95

Confidential

Transmission equipment parameters (BTS Alarm Sys-tem)

















































8260 ON OFF ON 10 10 UNBLOCKED8261 ON OFF ON 10 10 UNBLOCKED



DN998797 27


Id:0900d80580804c95

Confidential











8272 * OFF OFF ON 10 10 UNBLOCKED

8273 *** OFF OFF ON 10 10 UNBLOCKED




8277 *** OFF OFF ON 10 10 UNBLOCKED8278 *** OFF OFF ON 10 10 UNBLOCKED

8279 ** OFF OFF ON 10 10 UNBLOCKED


















28 DN998797


Id:0900d80580804c95

Confidential

8000 POWER SUPPLY FAULT

4 8000 POWER SUPPLY FAULT

Meaning

There is a fault in the power supply of a piece of transmissionequipment.

This alarm affects the provided services. The unit is not working

properly and the unit services can be lost.

Supplementary information fields

1 01 BSC supervises the equipment

02 BTS supervises the equipment

2 Q1 address of the piece of transmission equipment

3 the functional entity number specifies a physical unit of the

transmission equipment, for example a plug-in unit or a

daughter board. The number can be 0...254

4 the supervision block number specifies the faulty part of the

functional entity, for example a certain line interface or

component

5 number of the Q1 service channel in the BSC, 0...27.

If equipment is supervised by the BTS, the channel number

is not relevant

6 name of the piece of transmission equipment.

Not included if the name is in the alarm object field of

the alarm printout.

See alarm instructions

7 number of the piece of transmission equipment.

Not included if the index is in the alarm object field of

the alarm printout.


8 rack (cabinet) number FF = not defined

Included only if the equipment is supervised by a BTS that

supports coordinate settings

9 shelf number

FF = not defined



10 slot

FF = not defined



DN998797 29

Transmission Equipment Alarms (8000-8999) 8000 POWER SUPPLY FAULT

Id:0900d80580804c95

Confidential



Instructions

Check Supplementary information field 1 to see whether the BSC or

the BTS supervises the equipment.

If the BSC supervises the equipment, use the MML commands Axx for

alarm administration.

If the BTS supervises the equipment, use the MML commands EOx for


To clarify the reason for the fault, take a remote session to

transmission equipment and display fault information.

See the equipment operating manual for more detailed information on

the fault code and corrective actions.

Cancelling

Do not cancel the alarm. The system cancels the alarm automatically when

the fault has been corrected.



30 DN998797


Id:0900d80580804c95

Confidential

8001 TOTAL LOSS OF POWER SUPPLY

5 8001 TOTAL LOSS OF POWER SUPPLY

Meaning













component



is not relevant



the alarm printout.




the alarm printout.


8 rack (cabinet) number

FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 31

Transmission Equipment Alarms (8000-8999) 8001 TOTAL LOSS OF POWER SUPPLY

Id:0900d80580804c95

Confidential

FF = not defined



Instructions







To clarify the reason for the fault, take a remote session totransmission equipment and display fault information.



Cancelling





32 DN998797


Id:0900d80580804c95

Confidential

8002 LOSS OF BACK UP POWER SUPPLY

6 8002 LOSS OF BACK UP POWER SUPPLY

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 33

Transmission Equipment Alarms (8000-8999) 8002 LOSS OF BACK UP POWER SUPPLY

Id:0900d80580804c95

Confidential

FF = not defined



Instructions



If BSC supervises the equipment, use the MML commands Axx for


If BTS supervises the equipment, use the MML commands EOx for





Cancelling





34 DN998797


Id:0900d80580804c95

Confidential

8003 LOSS OF REMOTE POWER SUPPLY

7 8003 LOSS OF REMOTE POWER SUPPLY

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 35

Transmission Equipment Alarms (8000-8999) 8003 LOSS OF REMOTE POWER SUPPLY

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





36 DN998797


Id:0900d80580804c95

Confidential

8004 UNBALANCE IN REMOTE POWER SUPPLY

8 8004 UNBALANCE IN REMOTE POWER

SUPPLY

Meaning

There is a fault in the power supply of a piece of transmission

equipment.












component

5 number of the Q1 service channel in the BSC, 0...27. If equipment is supervised by the BTS, the channel number

is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined





DN998797 37

Transmission Equipment Alarms (8000-8999) 8004 UNBALANCE IN REMOTE POWER SUPPLY

Id:0900d80580804c95

Confidential

10 slot

FF = not defined



Instructions











Cancelling





38 DN998797


Id:0900d80580804c95

Confidential

8005 INCORRECT RINGING VOLTAGE

9 8005 INCORRECT RINGING VOLTAGE

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 39

Transmission Equipment Alarms (8000-8999) 8005 INCORRECT RINGING VOLTAGE

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





40 DN998797


Id:0900d80580804c95

Confidential

8006 FAULT IN CENTRAL BATTERY

10 8006 FAULT IN CENTRAL BATTERY

Meaning













component



is not relevant.



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 41

Transmission Equipment Alarms (8000-8999) 8006 FAULT IN CENTRAL BATTERY

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





42 DN998797


Id:0900d80580804c95

Confidential

8007 FAULT IN CRITERIA VOLTAGE

11 8007 FAULT IN CRITERIA VOLTAGE

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 43

Transmission Equipment Alarms (8000-8999) 8007 FAULT IN CRITERIA VOLTAGE

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





44 DN998797


Id:0900d80580804c95

Confidential

8008 LOW BATTERY VOLTAGE

12 8008 LOW BATTERY VOLTAGE

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 45

Transmission Equipment Alarms (8000-8999) 8008 LOW BATTERY VOLTAGE

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





46 DN998797


Id:0900d80580804c95

Confidential

8009 FAULT IN CURRENT LOOP

13 8009 FAULT IN CURRENT LOOP

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 47

Transmission Equipment Alarms (8000-8999) 8009 FAULT IN CURRENT LOOP

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





48 DN998797


Id:0900d80580804c95

Confidential

8010 SUPPLY UNIT VOLTAGE INCORRECT

14 8010 SUPPLY UNIT VOLTAGE INCORRECT

Meaning

A user operation inhibits the normal use of a piece of transmissionequipment function.

This alarm may affect the provided services. The unit is not working







transmission equipment, for example a plug-in unit or daughter

board. The number can be 0...254



component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 49

Transmission Equipment Alarms (8000-8999) 8010 SUPPLY UNIT VOLTAGE INCORRECT

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





50 DN998797


Id:0900d80580804c95

Confidential

8011 DISTRIBUTION FUSE FAULT

15 8011 DISTRIBUTION FUSE FAULT

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 51

Transmission Equipment Alarms (8000-8999) 8011 DISTRIBUTION FUSE FAULT

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





52 DN998797


Id:0900d80580804c95

Confidential

8012 SIGNALLING VOLTAGE FAULT

16 8012 SIGNALLING VOLTAGE FAULT

Meaning

There is a fault in the power supply of a piece of transmissionequipment power supply.








transmission equipment, for example a plug-in unit or a daughter

board. The number can be 0...254



component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 53

Transmission Equipment Alarms (8000-8999) 8012 SIGNALLING VOLTAGE FAULT

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





54 DN998797


Id:0900d80580804c95

Confidential

8013 CHARGER FAULT

17 8013 CHARGER FAULT

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 55

Transmission Equipment Alarms (8000-8999) 8013 CHARGER FAULT

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





56 DN998797


Id:0900d80580804c95

Confidential

8014 AC INPUT VOLTAGE FAILURE

18 8014 AC INPUT VOLTAGE FAILURE

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 57

Transmission Equipment Alarms (8000-8999) 8014 AC INPUT VOLTAGE FAILURE

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling

No cancelling.



58 DN998797


Id:0900d80580804c95

Confidential

8016 MAIN FUNCTION INHIBITED

19 8016 MAIN FUNCTION INHIBITED

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 59

Transmission Equipment Alarms (8000-8999) 8016 MAIN FUNCTION INHIBITED

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





60 DN998797


Id:0900d80580804c95

Confidential

8017 SIGNAL LOOPED TO TERMINAL

20 8017 SIGNAL LOOPED TO TERMINAL

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 61

Transmission Equipment Alarms (8000-8999) 8017 SIGNAL LOOPED TO TERMINAL

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





62 DN998797


Id:0900d80580804c95

Confidential

8018 SIGNAL IS LOOPED TO TRANSMISSION PATH

21 8018 SIGNAL IS LOOPED TO TRANSMISSION

PATH

Meaning

A user operation inhibits the normal use of a piece of transmission

equipment function.












component


is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined





DN998797 63

Transmission Equipment Alarms (8000-8999) 8018 SIGNAL IS LOOPED TO TRANSMISSION PATH

Id:0900d80580804c95

Confidential

10 slot

FF = not defined



Instructions











Cancelling





64 DN998797


Id:0900d80580804c95

Confidential

8019 FUNCTION INHIBITED

22 8019 FUNCTION INHIBITED

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 65

Transmission Equipment Alarms (8000-8999) 8019 FUNCTION INHIBITED

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





66 DN998797


Id:0900d80580804c95

Confidential

8020 BLOCKED FROM USE

23 8020 BLOCKED FROM USE

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 67

Transmission Equipment Alarms (8000-8999) 8020 BLOCKED FROM USE

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Flexi EDGE:

Description: A cross-connection is configured to an interface which

is not in use.

Instructions:

1. Check that all interfaces where cross connection termination

points have been set are in use. In cross connection window,

blocked cross connections are highlighted in Italic font.

2. Remove any unnecessary cross connections that have

termination point(s) to non-existing or unused interfaces.

Cancelling





68 DN998797


Id:0900d80580804c95

Confidential

8021 LOOP TO INTERFACE

24 8021 LOOP TO INTERFACE

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 69

Transmission Equipment Alarms (8000-8999) 8021 LOOP TO INTERFACE

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










FLEXI EDGE:

Description: PDH test-loop to Interface activated.

Instructions:

No actions required, alarm is cancelled when interface loop is

deactivated by the user with BTS Manager or after defined

timeout.

Cancelling





70 DN998797


Id:0900d80580804c95

Confidential

8022 LOOP TO EQUIPMENT

25 8022 LOOP TO EQUIPMENT

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 71

Transmission Equipment Alarms (8000-8999) 8022 LOOP TO EQUIPMENT

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










FLEXI EDGE:

Description: PDH test-loop to Equipment activated.

Instructions:

No actions required, alarm is cancelled when interface loop is

deactivated by the user with BTS Manager or after defined

timeout.

Cancelling





72 DN998797


Id:0900d80580804c95

Confidential

8023 TEST MODE

26 8023 TEST MODE

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 73

Transmission Equipment Alarms (8000-8999) 8023 TEST MODE

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





74 DN998797


Id:0900d80580804c95

Confidential

8024 LOOP IN EQUIPMENT

27 8024 LOOP IN EQUIPMENT

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 75

Transmission Equipment Alarms (8000-8999) 8024 LOOP IN EQUIPMENT

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





76 DN998797


Id:0900d80580804c95

Confidential

8025 TEST GENERATOR ON

28 8025 TEST GENERATOR ON

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 77

Transmission Equipment Alarms (8000-8999) 8025 TEST GENERATOR ON

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





78 DN998797


Id:0900d80580804c95

Confidential

8026 EXTERNAL TEST MODE ACTIVE

29 8026 EXTERNAL TEST MODE ACTIVE

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 79

Transmission Equipment Alarms (8000-8999) 8026 EXTERNAL TEST MODE ACTIVE

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





80 DN998797


Id:0900d80580804c95

Confidential

8027 BLOCKED FROM FAR END

30 8027 BLOCKED FROM FAR END

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 81

Transmission Equipment Alarms (8000-8999) 8027 BLOCKED FROM FAR END

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





82 DN998797


Id:0900d80580804c95

Confidential

8028 TIMESLOT RESERVED

31 8028 TIMESLOT RESERVED

Meaning













component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 83

Transmission Equipment Alarms (8000-8999) 8028 TIMESLOT RESERVED

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





84 DN998797


Id:0900d80580804c95

Confidential

8032 LOSS OF OUTGOING SIGNAL

32 8032 LOSS OF OUTGOING SIGNAL

Meaning

There is a fault in the outgoing signal of a piece of transmissionequipment.


properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 85

Transmission Equipment Alarms (8000-8999) 8032 LOSS OF OUTGOING SIGNAL

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





86 DN998797


Id:0900d80580804c95

Confidential

8033 LOSS OF OUTGOING 64K SIGNAL

33 8033 LOSS OF OUTGOING 64K SIGNAL

Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 87

Transmission Equipment Alarms (8000-8999) 8033 LOSS OF OUTGOING 64K SIGNAL

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





88 DN998797


Id:0900d80580804c95

Confidential


34 8034 LOSS OF OUTGOING 2M SIGNAL

Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 89

Transmission Equipment Alarms (8000-8999) 8034 LOSS OF OUTGOING 2M SIGNAL

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





90 DN998797


Id:0900d80580804c95

Confidential



Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 91


Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





92 DN998797


Id:0900d80580804c95

Confidential



Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 93


Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





94 DN998797


Id:0900d80580804c95

Confidential



Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 95


Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





96 DN998797


Id:0900d80580804c95

Confidential



Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 97


Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





98 DN998797


Id:0900d80580804c95

Confidential

8039 LOSS OF OUTGOING 0.7M SIGNAL

39 8039 LOSS OF OUTGOING 0.7M SIGNAL

Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 99

Transmission Equipment Alarms (8000-8999) 8039 LOSS OF OUTGOING 0.7M SIGNAL

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





100 DN998797


Id:0900d80580804c95

Confidential

8040 NO FREE CHANNEL

40 8040 NO FREE CHANNEL

Meaning

There is no available channel for connection, the channel is not freeor the channel cannot be taken in use.


properly and the unit services may be lost.










component


If the equipment is supervised by the BTS, the channel number

is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 101

Transmission Equipment Alarms (8000-8999) 8040 NO FREE CHANNEL

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling

No cancelling.



102 DN998797


Id:0900d80580804c95

Confidential

8042 LOSS OF OUTGOING TRANSMISSION PATHSIGNAL

41 8042 LOSS OF OUTGOING TRANSMISSION

PATH SIGNAL

Meaning

There is a fault in the outgoing signal of a piece of transmission

equipment.


properly.










component


is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined





DN998797 103

Transmission Equipment Alarms (8000-8999) 8042 LOSS OF OUTGOING TRANSMISSION PATHSIGNAL

Id:0900d80580804c95

Confidential

10 slot

FF = not defined



Instructions











Cancelling





104 DN998797


Id:0900d80580804c95

Confidential

8043 INCORRECT OUTGOING SIGNAL LEVEL

42 8043 INCORRECT OUTGOING SIGNAL

LEVEL

Meaning

There is a fault in the outgoing signal of a piece of transmission

equipment.


properly.










component


is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined





DN998797 105

Transmission Equipment Alarms (8000-8999) 8043 INCORRECT OUTGOING SIGNAL LEVEL

Id:0900d80580804c95

Confidential

10 slot

FF = not defined



Instructions











Cancelling





106 DN998797


Id:0900d80580804c95

Confidential

8044 HIGH REFLECTED POWER

43 8044 HIGH REFLECTED POWER

Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 107

Transmission Equipment Alarms (8000-8999) 8044 HIGH REFLECTED POWER

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





108 DN998797


Id:0900d80580804c95

Confidential

8045 NO OUTGOING SIGNAL

44 8045 NO OUTGOING SIGNAL

Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 109

Transmission Equipment Alarms (8000-8999) 8045 NO OUTGOING SIGNAL

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





110 DN998797


Id:0900d80580804c95

Confidential

8046 NO OUTGOING LINE SIGNAL

45 8046 NO OUTGOING LINE SIGNAL

Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 111

Transmission Equipment Alarms (8000-8999) 8046 NO OUTGOING LINE SIGNAL

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





DN998797 113

Transmission Equipment Alarms (8000-8999) 8047 PAYLOAD MISMATCH

Id:0900d80580804c95

Confidential


Instructions











Cancelling





114 DN998797


Id:0900d80580804c95

Confidential

8048 LOSS OF INCOMING SIGNAL

47 8048 LOSS OF INCOMING SIGNAL

Meaning

There is a fault in the incoming signal of a piece of transmissionequipment.

This alarm affects the provided services. The interface is not working

properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 115

Transmission Equipment Alarms (8000-8999) 8048 LOSS OF INCOMING SIGNAL

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Flexi EDGE:

Description: External Q1 device does not receive signal at its

interface (e.g. LMU has lost its GPS signal).

Instructions:

1. Find out the alarming Q1 device and refer to its product

documentation for more details on this alarm.

Cancelling





116 DN998797


Id:0900d80580804c95

Confidential

8049 LOSS OF INCOMING 64K SIGNAL

48 8049 LOSS OF INCOMING 64K SIGNAL

Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 117

Transmission Equipment Alarms (8000-8999) 8049 LOSS OF INCOMING 64K SIGNAL

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





118 DN998797


Id:0900d80580804c95

Confidential


49 8050 LOSS OF INCOMING 2M SIGNAL

Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 119

Transmission Equipment Alarms (8000-8999) 8050 LOSS OF INCOMING 2M SIGNAL

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Flexi EDGE:

Description: FIxx PIU has detected no incoming signal on E1

interface. Far End Alarm bit indication (TS0/b3) is sent in Tx

direction.

Instructions:

1. Check that interface settings are the same at both ends of

the link.

2. Check that the E1 cable is connected to right interface and

cable is correctly mated to the PIU. Check the condition of

cables, connectors and in case FIPA is used, check the

correct polarities of the wire pairs.

3. Replace FIxx

Cancelling





120 DN998797


Id:0900d80580804c95

Confidential



Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 121


Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





122 DN998797


Id:0900d80580804c95

Confidential



Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



124 DN998797


Id:0900d80580804c95

Confidential



Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 125


Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





126 DN998797


Id:0900d80580804c95

Confidential



Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 127


Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





128 DN998797


Id:0900d80580804c95

Confidential


54 8055 LOSS OF INCOMING 0.7M SIGNAL

Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



130 DN998797


Id:0900d80580804c95

Confidential


55 8056 LOSS OF INCOMING 1.5M SIGNAL

Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 131

Transmission Equipment Alarms (8000-8999) 8056 LOSS OF INCOMING 1.5M SIGNAL

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Flexi EDGE:

Description: FIxx PIU has detected no incoming signal on T1

interface. Yellow Alarm is sent in Tx direction.

1. Check that interface settings correspond to the actual link

characteristics.

2. Check that the T1 cable is connected to right interface and

cable is correctly mated to the PIU. Check the condition of

cables, connectors and correct polarities of the wire pairs.

3. Replace FIPA.

Cancelling





132 DN998797


Id:0900d80580804c95

Confidential

8057 LOSS OF POINTER

56 8057 LOSS OF POINTER

Meaning

Loss of Pointer condition has occurred.












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 133

Transmission Equipment Alarms (8000-8999) 8057 LOSS OF POINTER

Id:0900d80580804c95

Confidential


Instructions











Cancelling





134 DN998797


Id:0900d80580804c95

Confidential

8058 LOSS OF INCOMING TRANSMISSION PATHSIGNAL

57 8058 LOSS OF INCOMING TRANSMISSION

PATH SIGNAL

Meaning

There is a fault in the incoming signal of a piece of transmission

equipment.


properly.










component


is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined





DN998797 135

Transmission Equipment Alarms (8000-8999) 8058 LOSS OF INCOMING TRANSMISSION PATHSIGNAL

Id:0900d80580804c95

Confidential

10 slot

FF = not defined



Instructions











Cancelling





136 DN998797


Id:0900d80580804c95

Confidential

8059 INCORRECT INCOMING SIGNAL LEVEL

58 8059 INCORRECT INCOMING SIGNAL LEVEL

Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 137

Transmission Equipment Alarms (8000-8999) 8059 INCORRECT INCOMING SIGNAL LEVEL

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





138 DN998797


Id:0900d80580804c95

Confidential

8060 NO INCOMING RADIO SIGNAL

59 8060 NO INCOMING RADIO SIGNAL

Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 139

Transmission Equipment Alarms (8000-8999) 8060 NO INCOMING RADIO SIGNAL

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





140 DN998797


Id:0900d80580804c95

Confidential

8061 LOSS OF INCOMING LINE SIGNAL

60 8061 LOSS OF INCOMING LINE SIGNAL

Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



142 DN998797


Id:0900d80580804c95

Confidential

8062 NO CONNECTION

61 8062 NO CONNECTION

Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 143

Transmission Equipment Alarms (8000-8999) 8062 NO CONNECTION

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





144 DN998797


Id:0900d80580804c95

Confidential

8063 NO REDUNDANT CONNECTION

62 8063 NO REDUNDANT CONNECTION

Meaning



properly.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 145

Transmission Equipment Alarms (8000-8999) 8063 NO REDUNDANT CONNECTION

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





146 DN998797


Id:0900d80580804c95

Confidential

8064 ALARM SIGNAL (AIS) IS RECEIVED

63 8064 ALARM SIGNAL (AIS) IS RECEIVED

Meaning

A piece of transmission equipment receives an alarm signal from anotherpiece of equipment.

This alarm does not affect the provided services.










component



is not relevant



the alarm printout.




the alarm printout.



Included only if the equipment is supervised

by a BTS that supports coordin

ate settings

9 shelf number

FF = not defined





DN998797 147

Transmission Equipment Alarms (8000-8999) 8064 ALARM SIGNAL (AIS) IS RECEIVED

Id:0900d80580804c95

Confidential

10 slot

FF = not defined



Instructions











Cancelling





148 DN998797


Id:0900d80580804c95

Confidential


64 8065 ALARM SIGNAL (AIS 64K) IS RECEIVED

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined



DN998797 149

Transmission Equipment Alarms (8000-8999) 8065 ALARM SIGNAL (AIS 64K) IS RECEIVED

Id:0900d80580804c95

Confidential



Instructions











Cancelling





DN998797 151

Transmission Equipment Alarms (8000-8999) 8066 ALARM INDICATION SIGNAL (AIS) RECEIVED

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Flexi EDGE:

Description: The signal is cut, deteriorated or a equipment loop is

set in the far-end equipment. Alarm Indication Signal (AIS) is

indicated as "1111 1111" in all received time slots.

Instructions:

1. Check the transmission path to find where AIS insertion

occurs.

2. Check the alarms at the far-end. Refer to the product

documentation of the far-end equipment.

3. In case FIFA PIU is used, check that the microwave link

is commissioned and operational. Check that 2M cross

connections are configured at FIFA. Refer to the FIFA

product documentation for further instructions.

4. Replace FIxx.

Cancelling

Do not cancel the alarm. The system cancels the alarm automatically whenthe fault has been corrected.



152 DN998797


Id:0900d80580804c95

Confidential


66 8067 ALARM SIGNAL (AIS 8M) IS RECEIVED

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined



DN998797 153

Transmission Equipment Alarms (8000-8999) 8067 ALARM SIGNAL (AIS 8M) IS RECEIVED

Id:0900d80580804c95

Confidential



Instructions











Cancelling





154 DN998797


Id:0900d80580804c95

Confidential


67 8068 ALARM SIGNAL (AIS 34M) IS RECEIVED

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined



DN998797 155


Id:0900d80580804c95

Confidential



Instructions











Cancelling





156 DN998797


Id:0900d80580804c95

Confidential


68 8069 ALARM SIGNAL (AIS 140M) IS

RECEIVED

Meaning

A piece of transmission equipment receives an alarm signal from another

piece of equipment.











component


If equipment is supervised by the BTS, the channel number is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 157


Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





DN998797 159


Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





160 DN998797


Id:0900d80580804c95

Confidential

8071 ALARM SIGNAL (AIS 0.7M) IS RECEIVED

70 8071 ALARM SIGNAL (AIS 0.7M) IS

RECEIVED

Meaning


piece of equipment.











component





the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 161

Transmission Equipment Alarms (8000-8999) 8071 ALARM SIGNAL (AIS 0.7M) IS RECEIVED

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





162 DN998797


Id:0900d80580804c95

Confidential


71 8072 ALARM SIGNAL (AIS 16K) IS RECEIVED

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined



164 DN998797


Id:0900d80580804c95

Confidential


72 8073 ALARM INDICATION SIGNAL (AIS)

RECEIVED

Meaning


piece of equipment.











component





the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 165

Transmission Equipment Alarms (8000-8999) 8073 ALARM INDICATION SIGNAL (AIS) RECEIVED

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Flexi EDGE:

Description: The signal is cut, deteriorated or a equipment loop is

set in the far-end equipment. Alarm Indication Signal (AIS) is

indicated as "1111 1111" in all received time slots.

Instructions:

1. Check the transmission path to find where AIS insertion

occurs.

2. Check the alarms at the far-end. Refer to the product

documentation of the far-end equipment.

3. Replace FIPA.

Cancelling





166 DN998797


Id:0900d80580804c95

Confidential

8074 ALARM INDICATION SIGNAL RECEIVED ONTIMESLOT 16

73 8074 ALARM INDICATION SIGNAL

RECEIVED ON TIMESLOT 16

Meaning


piece of equipment.











component





the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



168 DN998797


Id:0900d80580804c95

Confidential

8075 S ALARM RECEIVED

74 8075 S ALARM RECEIVED

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined



DN998797 169

Transmission Equipment Alarms (8000-8999) 8075 S ALARM RECEIVED

Id:0900d80580804c95

Confidential



Instructions











Cancelling





172 DN998797


Id:0900d80580804c95

Confidential

8077 LOOPED SIGNAL RECEIVED

76 8077 LOOPED SIGNAL RECEIVED

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined



DN998797 173

Transmission Equipment Alarms (8000-8999) 8077 LOOPED SIGNAL RECEIVED

Id:0900d80580804c95

Confidential



Instructions











Cancelling





174 DN998797


Id:0900d80580804c95

Confidential

8078 MEASUREMENT SIGNAL RECEIVED

77 8078 MEASUREMENT SIGNAL RECEIVED

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined



DN998797 175

Transmission Equipment Alarms (8000-8999) 8078 MEASUREMENT SIGNAL RECEIVED

Id:0900d80580804c95

Confidential



Instructions











Cancelling





176 DN998797


Id:0900d80580804c95

Confidential

8079 TS16 CODE ERROR RECEIVED

78 8079 TS16 CODE ERROR RECEIVED

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined



DN998797 177

Transmission Equipment Alarms (8000-8999) 8079 TS16 CODE ERROR RECEIVED

Id:0900d80580804c95

Confidential



Instructions











Cancelling





178 DN998797


Id:0900d80580804c95

Confidential

8080 FRAME ERROR

79 8080 FRAME ERROR

Meaning

A framing error has been detected in the input signal.

This alarm affects the provided services.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined Included only if the equipment is supervised by a BTS that


9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 179

Transmission Equipment Alarms (8000-8999) 8080 FRAME ERROR

Id:0900d80580804c95

Confidential


Instructions











Cancelling





180 DN998797


Id:0900d80580804c95

Confidential

8081 LOSS OF FRAME ALIGNMENT

80 8081 LOSS OF FRAME ALIGNMENT

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




182 DN998797


Id:0900d80580804c95

Confidential

8082 MULTIFRAME ALIGNMENT LOST

81 8082 MULTIFRAME ALIGNMENT LOST

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 183

Transmission Equipment Alarms (8000-8999) 8082 MULTIFRAME ALIGNMENT LOST

Id:0900d80580804c95

Confidential


Instructions











Cancelling





184 DN998797


Id:0900d80580804c95

Confidential

8083 LOSS OF FRAME ALIGNMENT OF SUBSYS-TEM

82 8083 LOSS OF FRAME ALIGNMENT OF SUB-

SYSTEM

Meaning












component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot FF = not defined



DN998797 185

Transmission Equipment Alarms (8000-8999) 8083 LOSS OF FRAME ALIGNMENT OF SUBSYS-TEM

Id:0900d80580804c95

Confidential



Instructions











Cancelling





186 DN998797


Id:0900d80580804c95

Confidential

8084 LOSS OF LINE FRAME ALIGNMENT

83 8084 LOSS OF LINE FRAME ALIGNMENT

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 187

Transmission Equipment Alarms (8000-8999) 8084 LOSS OF LINE FRAME ALIGNMENT

Id:0900d80580804c95

Confidential


Instructions











Cancelling





DN998797 189

Transmission Equipment Alarms (8000-8999) 8085 LOSS OF RADIO FRAME ALIGNMENT

Id:0900d80580804c95

Confidential


Instructions











Cancelling





190 DN998797


Id:0900d80580804c95

Confidential

8086 LOSS OF CRC MULTIFRAME ALIGNMENT

85 8086 LOSS OF CRC MULTIFRAME ALIGN-

MENT

Meaning












component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






DN998797 191

Transmission Equipment Alarms (8000-8999) 8086 LOSS OF CRC MULTIFRAME ALIGNMENT

Id:0900d80580804c95

Confidential



Instructions











Flexi EDGE:

Description: CRC multiframe alignment signal lost or not received

on PDH interface. CRC multiframe alignment word is conveyed in

TS0 spread over a multiframe consisting of 16 E1 frames. Far End

Alarm bit indication (TS0/b3) is sent in Tx direction.

Instructions:

1. Check that the interface settings are the same at both ends and

the CRC is set in use.

2. Check that the far-end device is able to transmit signal with

CRC multiframe alignment enabled.

3. Check the condition of cables, connectors and correct polarities

of the wire pairs.

4. Check the signal quality of the transmission path to the alarming

equipment.

5. Replace FIxx.

Cancelling




196 DN998797


Id:0900d80580804c95

Confidential

8089 LOSS OF SIGNALLING FRAME

88 8089 LOSS OF SIGNALLING FRAME

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 197

Transmission Equipment Alarms (8000-8999) 8089 LOSS OF SIGNALLING FRAME

Id:0900d80580804c95

Confidential


Instructions











Cancelling





198 DN998797


Id:0900d80580804c95

Confidential

8096 EXCESSIVE ERROR RATE

89 8096 EXCESSIVE ERROR RATE

Meaning

The bit error rate has been exceeded in the input signal.











component


If equipment is supervised by the BTS the channel number

is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 199

Transmission Equipment Alarms (8000-8999) 8096 EXCESSIVE ERROR RATE

Id:0900d80580804c95

Confidential


Instructions











Cancelling





200 DN998797


Id:0900d80580804c95

Confidential


90 8097 BIT ERROR RATIO (BER) > 1E-1

Meaning












component


If equipment is supervised by the BTS the channel number

is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 201

Transmission Equipment Alarms (8000-8999) 8097 BIT ERROR RATIO (BER) > 1E-1

Id:0900d80580804c95

Confidential


Instructions











Cancelling





DN998797 203


Id:0900d80580804c95

Confidential


Instructions











Cancelling





DN998797 205

Transmission Equipment Alarms (8000-8999) 8099 RECEIVED BIT ERROR RATIO (BER) > 1E-3

Id:0900d80580804c95

Confidential



Instructions











Flexi EDGE and Flexi Multiradio:

Description: Received signal has degraded on E1/T1 interface. Bit

Error Ratio (BER) is over 1E-3.

Instructions:

1. If FIFA PIU is used, Refer to the FIFA product documentation

for instructions.

2. Check that the interface settings are correct for the link.

3. Check quality of the E1/T1 line by enabling a Loop to

Interface (line) at the far end equipment. If the alarm is

cancelled during the loop test, check the far-end equipment.

4. Equip an external cable loop to the interface to check that

the interface in FIxx is ok. If the alarm is still active

during the loop test, go to step 6.

5. Check the condition of cables, connectors and correct

polarities of the wire pairs.

6. Check that FIxx is fully inserted in to ESMA.

7. Replace FIxx.

8. Check the signal quality of the transmission path to the

alarming equipment.

Cancelling





206 DN998797


Id:0900d80580804c95

Confidential


93 8100 RECEIVED BIT ERROR RATIO (BER) >

1E-4

Meaning


This alarm may affect the provided services.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






208 DN998797


Id:0900d80580804c95

Confidential



1E-5

Meaning












component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






DN998797 209

Transmission Equipment Alarms (8000-8999) 8101 RECEIVED BIT ERROR RATIO (BER) > 1E-5

Id:0900d80580804c95

Confidential



Instructions











Cancelling





210 DN998797


Id:0900d80580804c95

Confidential



1E-6

Meaning












component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






212 DN998797


Id:0900d80580804c95

Confidential



Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 213


Id:0900d80580804c95

Confidential


Instructions











Cancelling





214 DN998797


Id:0900d80580804c95

Confidential



Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 215


Id:0900d80580804c95

Confidential


Instructions











Cancelling





216 DN998797


Id:0900d80580804c95

Confidential



Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 217


Id:0900d80580804c95

Confidential


Instructions











Cancelling





218 DN998797


Id:0900d80580804c95

Confidential



Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 219


Id:0900d80580804c95

Confidential


Instructions











Cancelling





220 DN998797


Id:0900d80580804c95

Confidential



Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 221


Id:0900d80580804c95

Confidential


Instructions











Cancelling





DN998797 223


Id:0900d80580804c95

Confidential


Instructions











Cancelling





224 DN998797


Id:0900d80580804c95

Confidential

8109 FADING IN TRANSMISSION PATH

102 8109 FADING IN TRANSMISSION PATH

Meaning

Fading has been detected in the input signal.











component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 225

Transmission Equipment Alarms (8000-8999) 8109 FADING IN TRANSMISSION PATH

Id:0900d80580804c95

Confidential


Instructions











Cancelling





226 DN998797


Id:0900d80580804c95

Confidential

8110 SELECTIVE FADING IN TRANSMISSION PATH

103 8110 SELECTIVE FADING IN TRANSMISSION

PATH

Meaning

Fading has been detected in the input signal.











component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






228 DN998797


Id:0900d80580804c95

Confidential

8111 MODULATION ERROR

104 8111 MODULATION ERROR

Meaning

A modulation error has been detected in the received signal.











component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 229

Transmission Equipment Alarms (8000-8999) 8111 MODULATION ERROR

Id:0900d80580804c95

Confidential


Instructions











Cancelling





DN998797 231

Transmission Equipment Alarms (8000-8999) 8112 FREQUENCY ERROR

Id:0900d80580804c95

Confidential


Instructions












Description: The node is running on the internal clock as

configured in the timing priority list. This alarm can also be raised

in case synchronisation protection is configured, when the Rx source

signals from both directions have its MCBs in state '1' .

Instructions:

1. Check that synchronisation priority list has Rx clock entries

for used interfaces.

2. In case FIFA PIU is used, check that the microwave link is

commissioned and operational. Refer to FIFA product documentation

for further instructions.

3. If any of the alarms 8050, 8066, 8081, 8099, 8056 or 8073 are

active, follow the instructions on them.

4. Check that interface cables are correctly mated to FIxx. Check

also condition of the connectors.

5. If BTS is part of PDH loop protection configuration, check

MCB/LCB configuration and operational state of loop network.

CancellingDo not cancel the alarm. The system cancels the alarm automatically when




232 DN998797


Id:0900d80580804c95

Confidential

8113 BUFFER OVERFLOW

106 8113 BUFFER OVERFLOW

Meaning

A frequency error has been detected in the input signal.











component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 233

Transmission Equipment Alarms (8000-8999) 8113 BUFFER OVERFLOW

Id:0900d80580804c95

Confidential


Instructions











Cancelling





234 DN998797


Id:0900d80580804c95

Confidential

8119 SYNCHRONIZING FAULT IN TRANSMITTER

107 8119 SYNCHRONIZING FAULT IN TRANSMIT-

TER

Meaning

A synchronization error has been detected.











component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






DN998797 235

Transmission Equipment Alarms (8000-8999) 8119 SYNCHRONIZING FAULT IN TRANSMITTER

Id:0900d80580804c95

Confidential



Instructions











Cancelling





236 DN998797


Id:0900d80580804c95

Confidential

8120 SYNCHRONIZING FAULT IN RECEIVER

108 8120 SYNCHRONIZING FAULT IN RECEIVER

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 237

Transmission Equipment Alarms (8000-8999) 8120 SYNCHRONIZING FAULT IN RECEIVER

Id:0900d80580804c95

Confidential


Instructions











Cancelling





DN998797 239

Transmission Equipment Alarms (8000-8999) 8121 SYNCHRONIZING FAULT IN AUXILIARYCHANNEL

Id:0900d80580804c95

Confidential



Instructions











Cancelling





240 DN998797


Id:0900d80580804c95

Confidential

8122 SYNCHRONIZING FAULT

110 8122 SYNCHRONIZING FAULT

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 241

Transmission Equipment Alarms (8000-8999) 8122 SYNCHRONIZING FAULT

Id:0900d80580804c95

Confidential


Instructions











Cancelling





242 DN998797


Id:0900d80580804c95

Confidential

8123 SYNCHRONIZING FAULT IN CARRIER RE-COVERY

111 8123 SYNCHRONIZING FAULT IN CARRIER

RECOVERY

Meaning












component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






DN998797 243

Transmission Equipment Alarms (8000-8999) 8123 SYNCHRONIZING FAULT IN CARRIER RE-COVERY

Id:0900d80580804c95

Confidential



Instructions











Cancelling





244 DN998797


Id:0900d80580804c95

Confidential

8124 SYNCHRONIZATION FAULT IN CLOCK RE-COVERY

112 8124 SYNCHRONIZATION FAULT IN CLOCK

RECOVERY

Meaning












component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






DN998797 247

Transmission Equipment Alarms (8000-8999) 8125 LOSS OF SYNCHRONIZATION SIGNAL

Id:0900d80580804c95

Confidential


Instructions











Flexi EDGE:

Description: All defined synchronisation sources in the

synchronisation priority list are invalid or the list is empty. Node

is running on its internal clock.

Instructions:

1. Check that synchronisation priority list has Rx clock entries

for used interfaces.

2. In case FIFA PIU is used, check that the microwave link is

commissioned and operational. Refer to FIFA product

documentation for further instructions.

3. If any of the alarms 8050, 8066, 8081, 8099, 8056 or 8073 are

active, follow the instructions on them.

4. Check that interface cables are correctly mated to FIxx. Check

also condition of the connectors.

5. Replace FIxx.

Cancelling





248 DN998797


Id:0900d80580804c95

Confidential

8126 UNIT FUNCTION DEGRADED

114 8126 UNIT FUNCTION DEGRADED

Meaning

A piece of equipment has detected a fault in its operation.











component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 249

Transmission Equipment Alarms (8000-8999) 8126 UNIT FUNCTION DEGRADED

Id:0900d80580804c95

Confidential


Instructions











Cancelling





250 DN998797


Id:0900d80580804c95

Confidential

8127 EQUIPMENT FAULT DETECTED IN AUTOMAT-IC LOOP TEST

115 8127 EQUIPMENT FAULT DETECTED IN

AUTOMATIC LOOP TEST

Meaning












component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






DN998797 251

Transmission Equipment Alarms (8000-8999) 8127 EQUIPMENT FAULT DETECTED IN AUTOMAT-IC LOOP TEST

Id:0900d80580804c95

Confidential



Instructions











Cancelling





252 DN998797


Id:0900d80580804c95

Confidential

8128 FAULT IN EQUIPMENT

116 8128 FAULT IN EQUIPMENT

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 253

Transmission Equipment Alarms (8000-8999) 8128 FAULT IN EQUIPMENT

Id:0900d80580804c95

Confidential


Instructions











Cancelling





DN998797 257

Transmission Equipment Alarms (8000-8999) 8130 FAULT IN MEMORY

Id:0900d80580804c95

Confidential


Instructions











Cancelling





258 DN998797


Id:0900d80580804c95

Confidential

8131 INTERNAL BUS FAULT

119 8131 INTERNAL BUS FAULT

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 259

Transmission Equipment Alarms (8000-8999) 8131 INTERNAL BUS FAULT

Id:0900d80580804c95

Confidential


Instructions











Cancelling





260 DN998797


Id:0900d80580804c95

Confidential

8132 FAULT IN SUMMING UNIT

120 8132 FAULT IN SUMMING UNIT

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 261

Transmission Equipment Alarms (8000-8999) 8132 FAULT IN SUMMING UNIT

Id:0900d80580804c95

Confidential


Instructions











Cancelling





262 DN998797


Id:0900d80580804c95

Confidential

8133 FAULT IN MUX

121 8133 FAULT IN MUX

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 263

Transmission Equipment Alarms (8000-8999) 8133 FAULT IN MUX

Id:0900d80580804c95

Confidential


Instructions











Cancelling





264 DN998797


Id:0900d80580804c95

Confidential

8134 EXCHANGE LINE ALARM

122 8134 EXCHANGE LINE ALARM

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 265

Transmission Equipment Alarms (8000-8999) 8134 EXCHANGE LINE ALARM

Id:0900d80580804c95

Confidential


Instructions











Cancelling





266 DN998797


Id:0900d80580804c95

Confidential

8135 EQUIPMENT IN RESET

123 8135 EQUIPMENT IN RESET

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 267

Transmission Equipment Alarms (8000-8999) 8135 EQUIPMENT IN RESET

Id:0900d80580804c95

Confidential


Instructions











Cancelling





268 DN998797


Id:0900d80580804c95

Confidential

8136 AIS OSCILLATOR FAULT

124 8136 AIS OSCILLATOR FAULT

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 269

Transmission Equipment Alarms (8000-8999) 8136 AIS OSCILLATOR FAULT

Id:0900d80580804c95

Confidential


Instructions











Cancelling





270 DN998797


Id:0900d80580804c95

Confidential

8137 OSCILLATOR FAULT

125 8137 OSCILLATOR FAULT

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 271

Transmission Equipment Alarms (8000-8999) 8137 OSCILLATOR FAULT

Id:0900d80580804c95

Confidential


Instructions











Cancelling





DN998797 273

Transmission Equipment Alarms (8000-8999) 8138 PRESSURE ALARM

Id:0900d80580804c95

Confidential


Instructions











Cancelling





274 DN998797


Id:0900d80580804c95

Confidential

8139 SUBRACK HAS MISSING UNITS

127 8139 SUBRACK HAS MISSING UNITS

Meaning

An installation or usage error has been detected in a piece ofequipment.











component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 275

Transmission Equipment Alarms (8000-8999) 8139 SUBRACK HAS MISSING UNITS

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





276 DN998797


Id:0900d80580804c95

Confidential

8140 SUBRACK HAS EXCESSIVE UNITS

128 8140 SUBRACK HAS EXCESSIVE UNITS

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined



DN998797 277

Transmission Equipment Alarms (8000-8999) 8140 SUBRACK HAS EXCESSIVE UNITS

Id:0900d80580804c95

Confidential



Instructions











Cancelling





278 DN998797


Id:0900d80580804c95

Confidential

8141 FORCED CONTROL ON

129 8141 FORCED CONTROL ON

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined



DN998797 279

Transmission Equipment Alarms (8000-8999) 8141 FORCED CONTROL ON

Id:0900d80580804c95

Confidential



Instructions











Cancelling





280 DN998797


Id:0900d80580804c95

Confidential

8142 INSTALLATION ERROR

130 8142 INSTALLATION ERROR

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined



282 DN998797


Id:0900d80580804c95

Confidential

8143 FAULT IN CHANGE OVER FUNCTION

131 8143 FAULT IN CHANGE OVER FUNCTION

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined



DN998797 283

Transmission Equipment Alarms (8000-8999) 8143 FAULT IN CHANGE OVER FUNCTION

Id:0900d80580804c95

Confidential



Instructions











Cancelling





284 DN998797


Id:0900d80580804c95

Confidential

8144 OPERATING ERROR

132 8144 OPERATING ERROR

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined



DN998797 285

Transmission Equipment Alarms (8000-8999) 8144 OPERATING ERROR

Id:0900d80580804c95

Confidential



Instructions











Cancelling





286 DN998797


Id:0900d80580804c95

Confidential

8145 TEMPERATURE ALARM

133 8145 TEMPERATURE ALARM

Meaning

A piece of equipment has detected an environmental error.











component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 287

Transmission Equipment Alarms (8000-8999) 8145 TEMPERATURE ALARM

Id:0900d80580804c95

Confidential


Instructions











Cancelling





288 DN998797


Id:0900d80580804c95

Confidential

8146 WIND ALARM

134 8146 WIND ALARM

Meaning

A piece of equipment has detected an environmental error.











component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 289

Transmission Equipment Alarms (8000-8999) 8146 WIND ALARM

Id:0900d80580804c95

Confidential


Instructions











Cancelling





290 DN998797


Id:0900d80580804c95

Confidential

8147 LOCAL ALARM CANCEL WITHOUT ANY ALARM

135 8147 LOCAL ALARM CANCEL WITHOUT ANY

ALARM

Meaning

A piece of equipment has detected a usage or operation failure.











component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






DN998797 291

Transmission Equipment Alarms (8000-8999) 8147 LOCAL ALARM CANCEL WITHOUT ANY ALARM

Id:0900d80580804c95

Confidential



Instructions











Cancelling

No cancelling.



292 DN998797


Id:0900d80580804c95

Confidential

8148 EQUIPMENT RESET

136 8148 EQUIPMENT RESET

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 293

Transmission Equipment Alarms (8000-8999) 8148 EQUIPMENT RESET

Id:0900d80580804c95

Confidential


Instructions











Flexi EDGE:

Description: This warning is issued by Q1 device when reset has

occurred.

Instructions:


documentation for more details on this warning message.

Cancelling

No cancelling.



294 DN998797


Id:0900d80580804c95

Confidential

8149 FORCED INDICATION

137 8149 FORCED INDICATION

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 295

Transmission Equipment Alarms (8000-8999) 8149 FORCED INDICATION

Id:0900d80580804c95

Confidential


Instructions











Cancelling

No cancelling.



296 DN998797


Id:0900d80580804c95

Confidential

8150 FAULT IN UNIT

138 8150 FAULT IN UNIT

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 297

Transmission Equipment Alarms (8000-8999) 8150 FAULT IN UNIT

Id:0900d80580804c95

Confidential


Instructions











Cancelling





298 DN998797


Id:0900d80580804c95

Confidential

8151 FAULT IN CHANNEL

139 8151 FAULT IN CHANNEL

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 299

Transmission Equipment Alarms (8000-8999) 8151 FAULT IN CHANNEL

Id:0900d80580804c95

Confidential


Instructions











Cancelling





300 DN998797


Id:0900d80580804c95

Confidential

8152 FAULT IN BLOCK

140 8152 FAULT IN BLOCK

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 301

Transmission Equipment Alarms (8000-8999) 8152 FAULT IN BLOCK

Id:0900d80580804c95

Confidential


Instructions











Cancelling





302 DN998797


Id:0900d80580804c95

Confidential

8153 FAULT IN TRANSMITTER

141 8153 FAULT IN TRANSMITTER

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 303

Transmission Equipment Alarms (8000-8999) 8153 FAULT IN TRANSMITTER

Id:0900d80580804c95

Confidential


Instructions











Cancelling





304 DN998797


Id:0900d80580804c95

Confidential

8154 FAULT IN RECEIVER

142 8154 FAULT IN RECEIVER

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 305

Transmission Equipment Alarms (8000-8999) 8154 FAULT IN RECEIVER

Id:0900d80580804c95

Confidential


Instructions











Cancelling





306 DN998797


Id:0900d80580804c95

Confidential

8155 LASER BIAS OUT OF RANGE

143 8155 LASER BIAS OUT OF RANGE

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 307

Transmission Equipment Alarms (8000-8999) 8155 LASER BIAS OUT OF RANGE

Id:0900d80580804c95

Confidential


Instructions











Cancelling





308 DN998797


Id:0900d80580804c95

Confidential

8156 LASER POWER OUT OF RANGE

144 8156 LASER POWER OUT OF RANGE

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 309

Transmission Equipment Alarms (8000-8999) 8156 LASER POWER OUT OF RANGE

Id:0900d80580804c95

Confidential


Instructions











Cancelling





310 DN998797


Id:0900d80580804c95

Confidential

8157 LASER TEMPERATURE OUT OF RANGE

145 8157 LASER TEMPERATURE OUT OF

RANGE

Meaning












component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






DN998797 311

Transmission Equipment Alarms (8000-8999) 8157 LASER TEMPERATURE OUT OF RANGE

Id:0900d80580804c95

Confidential



Instructions











Cancelling





312 DN998797


Id:0900d80580804c95

Confidential

8158 FORCED LASER CUT OFF

146 8158 FORCED LASER CUT OFF

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 313

Transmission Equipment Alarms (8000-8999) 8158 FORCED LASER CUT OFF

Id:0900d80580804c95

Confidential


Instructions











Cancelling





314 DN998797


Id:0900d80580804c95

Confidential

8159 RUN DIAGNOSTICS TEST

147 8159 RUN DIAGNOSTICS TEST

Meaning

The equipment has detected a fault in a diagnostics test.This alarm affects the provided services. The unit may not be working

properly.










component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 315

Transmission Equipment Alarms (8000-8999) 8159 RUN DIAGNOSTICS TEST

Id:0900d80580804c95

Confidential


Instructions











Cancelling





316 DN998797


Id:0900d80580804c95

Confidential

8160 INTERFACE UNIT FAULT

148 8160 INTERFACE UNIT FAULT

Meaning

A piece of equipment has detected a fault in its operation.This alarm may affect the provided services. The unit may not be

working properly.










component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 317

Transmission Equipment Alarms (8000-8999) 8160 INTERFACE UNIT FAULT

Id:0900d80580804c95

Confidential


Instructions











Cancelling





318 DN998797


Id:0900d80580804c95

Confidential

8161 CONNECTED TO REDUNDANT SYSTEM

149 8161 CONNECTED TO REDUNDANT SYSTEM

Meaning


working properly.










component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 319

Transmission Equipment Alarms (8000-8999) 8161 CONNECTED TO REDUNDANT SYSTEM

Id:0900d80580804c95

Confidential


Instructions











Cancelling





320 DN998797


Id:0900d80580804c95

Confidential

8162 DATABASE FULL

150 8162 DATABASE FULL

Meaning


working properly.










component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 321

Transmission Equipment Alarms (8000-8999) 8162 DATABASE FULL

Id:0900d80580804c95

Confidential


Instructions











Flexi EDGE:

Description: This warning is sent when the polling master

(BTS/BSC) is either unable to poll alarms from the Q1 device(s)

or it has not cleared the alarm history. Alarm history database has

become full.

Instructions:


documentation for more details on this warning message.

Cancelling

No cancelling.



322 DN998797


Id:0900d80580804c95

Confidential

8163 REDUNDANT CONNECTION IN USE

151 8163 REDUNDANT CONNECTION IN USE

Meaning


working properly.










component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 323

Transmission Equipment Alarms (8000-8999) 8163 REDUNDANT CONNECTION IN USE

Id:0900d80580804c95

Confidential


Instructions











Cancelling





324 DN998797


Id:0900d80580804c95

Confidential

8164 LINE CABLE FAULT

152 8164 LINE CABLE FAULT

Meaning


working properly.










component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 325

Transmission Equipment Alarms (8000-8999) 8164 LINE CABLE FAULT

Id:0900d80580804c95

Confidential


Instructions











Cancelling





326 DN998797


Id:0900d80580804c95

Confidential

8165 REAL TIME LOST

153 8165 REAL TIME LOST

Meaning


working properly.










component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 327

Transmission Equipment Alarms (8000-8999) 8165 REAL TIME LOST

Id:0900d80580804c95

Confidential


Instructions











Flexi EDGE:

Description: Q1 device has not received real time from the polling

master (BTS/BSC). Time stamps are not displayed correctly.

Instructions:


documentation for more details on this alarm.

Cancelling





328 DN998797


Id:0900d80580804c95

Confidential

8166 E1 CONVERTER RESET

154 8166 E1 CONVERTER RESET

Meaning


working properly.










component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 329

Transmission Equipment Alarms (8000-8999) 8166 E1 CONVERTER RESET

Id:0900d80580804c95

Confidential


Instructions











Cancelling





330 DN998797


Id:0900d80580804c95

Confidential

8167 E1 CONVERTER FAULT

155 8167 E1 CONVERTER FAULT

Meaning


working properly.










component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 331

Transmission Equipment Alarms (8000-8999) 8167 E1 CONVERTER FAULT

Id:0900d80580804c95

Confidential


Instructions











Cancelling





332 DN998797


Id:0900d80580804c95

Confidential

8168 EQUIPMENT DOOR OPEN

156 8168 EQUIPMENT DOOR OPEN

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 333

Transmission Equipment Alarms (8000-8999) 8168 EQUIPMENT DOOR OPEN

Id:0900d80580804c95

Confidential


Instructions











Cancelling





334 DN998797


Id:0900d80580804c95

Confidential

8169 EXTENDED FAULT CODE IN USE

157 8169 EXTENDED FAULT CODE IN USE

Meaning

The BSC or BTS does not recognise the received fault code. Theequipment is supervised by the TMS4 polling system and does not

understand the extended fault codes.

This alarm may affect the provided services depending on the

actual fault.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined





DN998797 335

Transmission Equipment Alarms (8000-8999) 8169 EXTENDED FAULT CODE IN USE

Id:0900d80580804c95

Confidential

10 slot

FF = not defined



Instructions











Cancelling





336 DN998797


Id:0900d80580804c95

Confidential

8172 YELLOW ALARM OCCURRED

158 8172 YELLOW ALARM OCCURRED

Meaning

The yellow alarm is sent by the equipment in the far-end, itindicates a serious fault in the received signal of the far-end

equipment.










component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 337

Transmission Equipment Alarms (8000-8999) 8172 YELLOW ALARM OCCURRED

Id:0900d80580804c95

Confidential


Instructions











Flexi EDGE:

Instructions:

1. Check the far end equipment for alarms 8056, 8073, 8081.

See the instructions on them.

2. Apply Loop to interface (line) at far end to check that link

is ok. If 8056/8073/8081 alarm is not active at near-end

during the loop test the problem is at the far-end receiver.

Note: 8172 Yellow alarm will be cancelled during this test.


the interface in FIxx is ok. If 8056/8073/8081 alarm is active

during the loop test, go to step 5. Note: 8172 Yellow alarm

will be cancelled during this test.




6. Replace FIxx.

Cancelling


Flexi EDGE:

Do not cancel the alarm. The alarm is cancelled automatically when Yellow

alarm (RAI) clearance is detected according to ANSI T1.231.



338 DN998797


Id:0900d80580804c95

Confidential


159 8173 FAR-END ALARM 4

Meaning

A piece of transmission equipment has received a far-end alarm.











component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 339

Transmission Equipment Alarms (8000-8999) 8173 FAR-END ALARM 4

Id:0900d80580804c95

Confidential


Instructions











Cancelling

No cancelling.



340 DN998797


Id:0900d80580804c95

Confidential



Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 341


Id:0900d80580804c95

Confidential


Instructions











Cancelling





342 DN998797


Id:0900d80580804c95

Confidential



Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 343


Id:0900d80580804c95

Confidential


Instructions











Cancelling





344 DN998797


Id:0900d80580804c95

Confidential

8176 FAR-END ALARM RECEIVED

162 8176 FAR-END ALARM RECEIVED

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 345

Transmission Equipment Alarms (8000-8999) 8176 FAR-END ALARM RECEIVED

Id:0900d80580804c95

Confidential


Instructions











Cancelling





346 DN998797


Id:0900d80580804c95

Confidential

8178 MULTIFRAME ALARM FROM FAR-END

163 8178 MULTIFRAME ALARM FROM FAR-END

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 347

Transmission Equipment Alarms (8000-8999) 8178 MULTIFRAME ALARM FROM FAR-END

Id:0900d80580804c95

Confidential


Instructions











Cancelling





348 DN998797


Id:0900d80580804c95

Confidential

8179 FAR-END ALARM

164 8179 FAR-END ALARM

Meaning

Sent by the equipment in the far-end (TS0 Bit 3), which indicatesthat far-end equipment is unable to receive the signal.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined

Included only if the equipment is supervised by a BTS that supports coordinate settings

9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 349

Transmission Equipment Alarms (8000-8999) 8179 FAR-END ALARM

Id:0900d80580804c95

Confidential


Instructions











Flexi EDGE:

Instructions:

1. Check the far end equipment for alarms 8050, 8066, 8081

and 8086. See the instructions on them.

2. Apply Loop to interface (line) at far end to check that link

is ok. If 8050/8066/8081/8086 alarm is not active at near-end

during the loop test the problem is at the far-end receiver.

Note: 8179 Far-end alarm will be cancelled during this test.


the interface in FIxx is ok. If 8050/8066/8081/8086 alarm

is active during the loop test, go to step 5.

Note: 8179 Far-end alarm will be cancelled during this test.




6. Replace FIxx.

Cancelling




350 DN998797


Id:0900d80580804c95

Confidential

8180 ALARM FROM FAR-END SUBSYSTEM

165 8180 ALARM FROM FAR-END SUBSYSTEM

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 351

Transmission Equipment Alarms (8000-8999) 8180 ALARM FROM FAR-END SUBSYSTEM

Id:0900d80580804c95

Confidential


Instructions











Cancelling





352 DN998797


Id:0900d80580804c95

Confidential

8181 FAR-END SENDING FAULT

166 8181 FAR-END SENDING FAULT

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 353

Transmission Equipment Alarms (8000-8999) 8181 FAR-END SENDING FAULT

Id:0900d80580804c95

Confidential


Instructions











Cancelling





354 DN998797


Id:0900d80580804c95

Confidential

8182 FAULT IN FAR-END RECEIVING

167 8182 FAULT IN FAR-END RECEIVING

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 355

Transmission Equipment Alarms (8000-8999) 8182 FAULT IN FAR-END RECEIVING

Id:0900d80580804c95

Confidential


Instructions











Cancelling





356 DN998797


Id:0900d80580804c95

Confidential

8183 FAR-END SYNCHRONIZATION ALARM

168 8183 FAR-END SYNCHRONIZATION ALARM

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 357

Transmission Equipment Alarms (8000-8999) 8183 FAR-END SYNCHRONIZATION ALARM

Id:0900d80580804c95

Confidential


Instructions











Cancelling





358 DN998797


Id:0900d80580804c95

Confidential

8184 REAL TIME UPDATED

169 8184 REAL TIME UPDATED

Meaning

Real time is updated to the equipment. The equipment's time changeexceeds the alarm threshold.











component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined



DN998797 359

Transmission Equipment Alarms (8000-8999) 8184 REAL TIME UPDATED

Id:0900d80580804c95

Confidential



Instructions







This alarm does not require any action. The system has updated

the equipment time more than the alarm threshold.


the fault code.

Cancelling

No cancelling.



360 DN998797


Id:0900d80580804c95

Confidential

8185 CONNECTION OR SETTINGS HAVECHANGED

170 8185 CONNECTION OR SETTINGS HAVE

CHANGED

Meaning

Connection or settings have changed in a piece of transmission

equipment.











component





the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 361

Transmission Equipment Alarms (8000-8999) 8185 CONNECTION OR SETTINGS HAVECHANGED

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling

No cancelling.



362 DN998797


Id:0900d80580804c95

Confidential

8186 CONFIGURATION ERROR

171 8186 CONFIGURATION ERROR

Meaning

A configuration error has been detected in a piece of equipment.











component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 363

Transmission Equipment Alarms (8000-8999) 8186 CONFIGURATION ERROR

Id:0900d80580804c95

Confidential


Instructions










fault code and corrective actions.

Cancelling





364 DN998797


Id:0900d80580804c95

Confidential


172 8190 CUSTOMER SPECIFIC FAULT CODE 1

Meaning

This alarm is generated from a customer specific fault code.











component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 365

Transmission Equipment Alarms (8000-8999) 8190 CUSTOMER SPECIFIC FAULT CODE 1

Id:0900d80580804c95

Confidential


Instructions











Cancelling





366 DN998797


Id:0900d80580804c95

Confidential



Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 367


Id:0900d80580804c95

Confidential


Instructions











Cancelling





368 DN998797


Id:0900d80580804c95

Confidential



Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 369


Id:0900d80580804c95

Confidential


Instructions











Cancelling





370 DN998797


Id:0900d80580804c95

Confidential



Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 371


Id:0900d80580804c95

Confidential


Instructions











Cancelling





372 DN998797


Id:0900d80580804c95

Confidential



Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 373


Id:0900d80580804c95

Confidential


Instructions











Cancelling





374 DN998797


Id:0900d80580804c95

Confidential

8195 V5 PROTOCOL ALARM

177 8195 V5 PROTOCOL ALARM

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 375

Transmission Equipment Alarms (8000-8999) 8195 V5 PROTOCOL ALARM

Id:0900d80580804c95

Confidential


Instructions











Cancelling





376 DN998797


Id:0900d80580804c95

Confidential

8200 LOSS OF PRIMARY SUPERVISION CONNEC-TION

178 8200 LOSS OF PRIMARY SUPERVISION

CONNECTION

Meaning

A piece of equipment has detected a supervision connection fault.











component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






DN998797 377

Transmission Equipment Alarms (8000-8999) 8200 LOSS OF PRIMARY SUPERVISION CONNEC-TION

Id:0900d80580804c95

Confidential



Instructions











Cancelling





378 DN998797


Id:0900d80580804c95

Confidential

8201 LOSS OF SECONDARY SUPERVISION CON-NECTION

179 8201 LOSS OF SECONDARY SUPERVISION

CONNECTION

Meaning

A piece of equipment has detected a supervision connection fault.











component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot




DN998797 379

Transmission Equipment Alarms (8000-8999) 8201 LOSS OF SECONDARY SUPERVISION CON-NECTION

Id:0900d80580804c95

Confidential


Instructions











Cancelling





380 DN998797


Id:0900d80580804c95

Confidential

8202 LOSS OF SUPERVISION CONNECTION

180 8202 LOSS OF SUPERVISION CONNECTION

Meaning

A piece of equipment has detected a supervision connection fault.This alarm affects the provided services.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined


9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 381

Transmission Equipment Alarms (8000-8999) 8202 LOSS OF SUPERVISION CONNECTION

Id:0900d80580804c95

Confidential


Instructions











Flexi EDGE:

Description: Q1 device doesn't respond to poll command sent by the

polling master (BTS/BSC).

Instructions:

1. Check that Q1 baud rate and Q1 address of the Q1 device matches

with what is configured at the BSC.

2. Check if alarm 7601 "Q1 bus faulty" is active. Check that the

cable is correctly mated with the ESMA and Q1 device. Check also

condition of the Q1 cable connectors.

3. Check that Q1 switches are set to enable polling master (BTS/BSC)

to access the microprocessor (up) of the Q1 device.

4. Replace ESMA.

Cancelling





382 DN998797


Id:0900d80580804c95

Confidential

8203 LOSS OF SUPERVISION BUS

181 8203 LOSS OF SUPERVISION BUS

Meaning

A piece of equipment has detected a supervision connection fault.This alarm affects the provided services.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined


9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 383

Transmission Equipment Alarms (8000-8999) 8203 LOSS OF SUPERVISION BUS

Id:0900d80580804c95

Confidential


Instructions











Cancelling





384 DN998797


Id:0900d80580804c95

Confidential

8206 CONGESTION

182 8206 CONGESTION

Meaning

There is congestion in the equipment or in the plug-in unit. Resource orservice has congestion and requested operation cannot be executed.












component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot

FF = not defined



DN998797 385

Transmission Equipment Alarms (8000-8999) 8206 CONGESTION

Id:0900d80580804c95

Confidential



Instructions











Cancelling

No cancelling.



386 DN998797


Id:0900d80580804c95

Confidential

8207 CALIBRATION EXPIRED

183 8207 CALIBRATION EXPIRED

Meaning

Recalibration is needed.












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 387

Transmission Equipment Alarms (8000-8999) 8207 CALIBRATION EXPIRED

Id:0900d80580804c95

Confidential


Instructions











Cancelling

No cancelling.



388 DN998797


Id:0900d80580804c95

Confidential

8213 REMOTE DEFECT INDICATION (RDI)

184 8213 REMOTE DEFECT INDICATION (RDI)

Meaning

A remote end indicates failure in the termination point.











component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 389

Transmission Equipment Alarms (8000-8999) 8213 REMOTE DEFECT INDICATION (RDI)

Id:0900d80580804c95

Confidential


Instructions











Cancelling





390 DN998797


Id:0900d80580804c95

Confidential

8214 SIGNAL DEGRADED

185 8214 SIGNAL DEGRADED

Meaning

The signal is degraded.











component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 391

Transmission Equipment Alarms (8000-8999) 8214 SIGNAL DEGRADED

Id:0900d80580804c95

Confidential


Instructions











Cancelling





392 DN998797


Id:0900d80580804c95

Confidential

8215 TRACE IDENTIFIER MISMATCH

186 8215 TRACE IDENTIFIER MISMATCH

Meaning

The trace identifier does not match the expected one.











component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 393

Transmission Equipment Alarms (8000-8999) 8215 TRACE IDENTIFIER MISMATCH

Id:0900d80580804c95

Confidential


Instructions











Cancelling





394 DN998797


Id:0900d80580804c95

Confidential

8216 UNEQUIPPED SIGNAL

187 8216 UNEQUIPPED SIGNAL

Meaning

Virtual Container (VC) does not carry valid payload data because thecross-connection is not configured.











component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 395

Transmission Equipment Alarms (8000-8999) 8216 UNEQUIPPED SIGNAL

Id:0900d80580804c95

Confidential


Instructions











Cancelling





396 DN998797


Id:0900d80580804c95

Confidential

8221 VERSION MISMATCH

188 8221 VERSION MISMATCH

Meaning

The software or program version is not compatible with the hardware,other software versions or software information.












component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot

FF = not defined



DN998797 397

Transmission Equipment Alarms (8000-8999) 8221 VERSION MISMATCH

Id:0900d80580804c95

Confidential



Instructions











Cancelling





398 DN998797


Id:0900d80580804c95

Confidential

8222 CORRUPT DATA

189 8222 CORRUPT DATA

Meaning

The received or stored data is corrupted. The data content is notwhat it was expected to be.












component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot

FF = not defined



DN998797 399

Transmission Equipment Alarms (8000-8999) 8222 CORRUPT DATA

Id:0900d80580804c95

Confidential



Instructions











Cancelling





DN998797 401

Transmission Equipment Alarms (8000-8999) 8223 PROTECTION SWITCH

Id:0900d80580804c95

Confidential



Instructions











Cancelling

No cancelling.



402 DN998797


Id:0900d80580804c95

Confidential

8230 THRESHOLD CROSSED

191 8230 THRESHOLD CROSSED

Meaning

A piece of equipment has detected a performance monitoring fault.











component



is not relevant

6 ascii string of the piece of transmission equipment type.


the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 403

Transmission Equipment Alarms (8000-8999) 8230 THRESHOLD CROSSED

Id:0900d80580804c95

Confidential


Instructions











Cancelling

No cancelling.



404 DN998797


Id:0900d80580804c95

Confidential

8240 ACTIVE ALARM POINT

192 8240 ACTIVE ALARM POINT

Meaning

This is an external alarm connected to a piece of transmissionequipment.











component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined



DN998797 405

Transmission Equipment Alarms (8000-8999) 8240 ACTIVE ALARM POINT

Id:0900d80580804c95

Confidential



Instructions











Flexi EDGE:

Description: This is an external user-defined alarm. This alarm is

activated at the external equipment. Alarrm line number is mapped to

Supervision Block number. EAC lines can be routed via EAC port at ESMA

or via FSEx connected to ESMA.

Instructions:

1. Check that the relevant EAC line is correctly configured at the

BSC (MML command ZEFO:<id>:IOP;).

2. Check equipment connected to alarming EAC line.

3. Check that the cable chain is correctly mated between ESMA and

the external equipment.

4. Check the ESMA and replace it if faulty.

Cancelling





DN998797 407

Transmission Equipment Alarms (8000-8999) 8241 UPPER ALARM LIMIT EXCEEDED

Id:0900d80580804c95

Confidential



Instructions











Cancelling





DN998797 409

Transmission Equipment Alarms (8000-8999) 8242 LOWER ALARM LIMIT EXCEEDED

Id:0900d80580804c95

Confidential



Instructions











Cancelling





410 DN998797


Id:0900d80580804c95

Confidential

8250 INVALID TIME

195 8250 INVALID TIME

Meaning

This is a transmission equipment alarm generated by a mediator device.The mediator has detected that the time in the alarm is in the future

or too far away in the past.












component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 411

Transmission Equipment Alarms (8000-8999) 8250 INVALID TIME

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





412 DN998797


Id:0900d80580804c95

Confidential

8254 OPERATOR DISABLED

196 8254 OPERATOR DISABLED

Meaning

This is a transmission equipment alarm generated by a mediator device.











component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 413

Transmission Equipment Alarms (8000-8999) 8254 OPERATOR DISABLED

Id:0900d80580804c95

Confidential


Instructions











Cancelling

No cancelling.



414 DN998797


Id:0900d80580804c95

Confidential

8256 15 MIN G826 ES THRESHOLD CROSSED

197 8256 15 MIN G826 ES THRESHOLD

CROSSED

Meaning












component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






DN998797 415

Transmission Equipment Alarms (8000-8999) 8256 15 MIN G826 ES THRESHOLD CROSSED

Id:0900d80580804c95

Confidential



Instructions











Cancelling





416 DN998797


Id:0900d80580804c95

Confidential

8257 15 MIN G826 SES THRESHOLD CROSSED

198 8257 15 MIN G826 SES THRESHOLD

CROSSED

Meaning












component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






DN998797 417

Transmission Equipment Alarms (8000-8999) 8257 15 MIN G826 SES THRESHOLD CROSSED

Id:0900d80580804c95

Confidential



Instructions











Cancelling





418 DN998797


Id:0900d80580804c95

Confidential

8258 15 MIN G826 BBE THRESHOLD CROSSED

199 8258 15 MIN G826 BBE THRESHOLD

CROSSED

Meaning












component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






DN998797 419

Transmission Equipment Alarms (8000-8999) 8258 15 MIN G826 BBE THRESHOLD CROSSED

Id:0900d80580804c95

Confidential



Instructions











Cancelling





420 DN998797


Id:0900d80580804c95

Confidential

8259 24 H G826 ES THRESHOLD CROSSED

200 8259 24 H G826 ES THRESHOLD CROSSED

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 421

Transmission Equipment Alarms (8000-8999) 8259 24 H G826 ES THRESHOLD CROSSED

Id:0900d80580804c95

Confidential


Instructions











Cancelling

No cancelling.



422 DN998797


Id:0900d80580804c95

Confidential

8260 24 H G826 SES THRESHOLD CROSSED

201 8260 24 H G826 SES THRESHOLD CROSSED

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 423

Transmission Equipment Alarms (8000-8999) 8260 24 H G826 SES THRESHOLD CROSSED

Id:0900d80580804c95

Confidential


Instructions











Cancelling

No cancelling.



424 DN998797


Id:0900d80580804c95

Confidential

8261 24 H G826 BBE THRESHOLD CROSSED

202 8261 24 H G826 BBE THRESHOLD CROSSED

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 425

Transmission Equipment Alarms (8000-8999) 8261 24 H G826 BBE THRESHOLD CROSSED

Id:0900d80580804c95

Confidential


Instructions











Cancelling

No cancelling.



426 DN998797


Id:0900d80580804c95

Confidential

8262 STATISTIC UNAVAILABILITY

203 8262 STATISTIC UNAVAILABILITY

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 427

Transmission Equipment Alarms (8000-8999) 8262 STATISTIC UNAVAILABILITY

Id:0900d80580804c95

Confidential


Instructions











Cancelling





428 DN998797


Id:0900d80580804c95

Confidential

8263 STATISTIC RESET

204 8263 STATISTIC RESET

Meaning












component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 429

Transmission Equipment Alarms (8000-8999) 8263 STATISTIC RESET

Id:0900d80580804c95

Confidential


Instructions











Cancelling

No cancelling.



430 DN998797


Id:0900d80580804c95

Confidential

8264 15 MIN T/RLTS THRESHOLD CROSSED

205 8264 15 MIN T/RLTS THRESHOLD CROSSED

Meaning

In the radio interface a T/RLTS is a one-second period during whichthe detected transmitted level (TL) value is higher or the received

level (RL) value is lower than a predefined reference threshold.

If the number of seconds counted in a time interval is higher than

the predefined threshold value, this event is generated.












component



is not relevant



the alarm printout.



Not included if the index is in the alarm object field of the alarm printout.



FF = not defined



9 shelf number

FF = not defined





DN998797 431

Transmission Equipment Alarms (8000-8999) 8264 15 MIN T/RLTS THRESHOLD CROSSED

Id:0900d80580804c95

Confidential

10 slot

FF = not defined



Instructions











Cancelling





432 DN998797


Id:0900d80580804c95

Confidential

8265 24 H T/RLTS THRESHOLD CROSSED

206 8265 24 H T/RLTS THRESHOLD CROSSED

Meaning

In the radio interface a T/RLTS is a one-second period during whichthe detected transmitted level (TL) value is higher or the received

level (RL) value is lower than a predefined reference threshold.

If the number of seconds counted in a time interval is higher than

a predefined threshold value, this event is generated.












component



is not relevant



the alarm printout.






FF = not defined



9 shelf number

FF = not defined





DN998797 433

Transmission Equipment Alarms (8000-8999) 8265 24 H T/RLTS THRESHOLD CROSSED

Id:0900d80580804c95

Confidential

10 slot

FF = not defined



Instructions











Cancelling

No cancelling.



434 DN998797


Id:0900d80580804c95

Confidential

8266 LICENCE KEY NOT VALID

207 8266 LICENCE KEY NOT VALID

Meaning

The licence key does not fit the unit or the feature.











component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 435

Transmission Equipment Alarms (8000-8999) 8266 LICENCE KEY NOT VALID

Id:0900d80580804c95

Confidential


Instructions











Cancelling





436 DN998797


Id:0900d80580804c95

Confidential

8267 LICENCE EXPIRED

208 8267 LICENCE EXPIRED

Meaning

Licence has expired. The feature has been deactivated.











component



is not relevant



the alarm printout.




the alarm printout.





9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 437

Transmission Equipment Alarms (8000-8999) 8267 LICENCE EXPIRED

Id:0900d80580804c95

Confidential


Instructions











Cancelling





438 DN998797


Id:0900d80580804c95

Confidential

8268 LICENCE WILL EXPIRE IN THE NEAR FUTURE

209 8268 LICENCE WILL EXPIRE IN THE NEAR

FUTURE

Meaning

The licence is time limited. The feature will not be usable after

licence expiration.











component





the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






DN998797 439

Transmission Equipment Alarms (8000-8999) 8268 LICENCE WILL EXPIRE IN THE NEAR FUTURE

Id:0900d80580804c95

Confidential



Instructions











Cancelling





440 DN998797


Id:0900d80580804c95

Confidential

8269 LICENCE FOR FEATURE IS NOT AVAILABLE

210 8269 LICENCE FOR FEATURE IS NOT AVAIL-

ABLE

Meaning

The feature cannot be activated without a licence.











component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot




DN998797 441

Transmission Equipment Alarms (8000-8999) 8269 LICENCE FOR FEATURE IS NOT AVAILABLE

Id:0900d80580804c95

Confidential


Instructions











Cancelling





442 DN998797


Id:0900d80580804c95

Confidential

8270 LICENCE FOR FEATURE HAS BEEN ACTIVAT-ED

211 8270 LICENCE FOR FEATURE HAS BEEN

ACTIVATED

Meaning

The user has activated the licence for the feature.











component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot




DN998797 443

Transmission Equipment Alarms (8000-8999) 8270 LICENCE FOR FEATURE HAS BEEN ACTIVAT-ED

Id:0900d80580804c95

Confidential


Instructions











Cancelling





444 DN998797


Id:0900d80580804c95

Confidential

8271 LICENCE FOR FEATURE HAS BEEN DEACTI-VATED

212 8271 LICENCE FOR FEATURE HAS BEEN

DEACTIVATED

Meaning

The user has deactivated the licence for the feature.











component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot




DN998797 445

Transmission Equipment Alarms (8000-8999) 8271 LICENCE FOR FEATURE HAS BEEN DEACTI-VATED

Id:0900d80580804c95

Confidential


Instructions











Cancelling





446 DN998797


Id:0900d80580804c95

Confidential

8272 POSITION NOT LOCKED

213 8272 POSITION NOT LOCKED

Meaning

The global positioning system (GPS) position is not locked becausea GPS receiver self survey is ongoing. The location measurement unit(LMU)

GPS position is not locked. A minimum of four satellite signals are

needed to achieve GPS FIX.

The GPS position survey takes about 24 hours with a good satellite view.

If the self survey is not completed within a reasonable time(it may take

from one to five days), check the GPS antenna installation.





3 the functional entity number specifies the physical unit of the





component

5 the number of the Q1 service channel in the BSC. The number can

be 0...27. If the equipment is supervised by the BTS, the channel

number is not relevant

6 the name of the piece of transmission equipment.


the alarm printout.

For more information, see the alarm's instructions

7 the number of the piece of transmission equipment.




FF = not defined



9 shelf number

FF = not defined





DN998797 447

Transmission Equipment Alarms (8000-8999) 8272 POSITION NOT LOCKED

Id:0900d80580804c95

Confidential

10 slot

FF = not defined



Instructions

Check the Supplementary information field 1 to see whether the BSC or






To clarify the reason for the fault, open a remote session to the

transmission equipment and display the fault information.

For more detailed information on the fault code and corrective actions,

see the equipment's operating manual.

Flexi EDGE:

Description: The LMUB power is out of its normal operating limits or the

fuse-link is blown due to over-current.

Instructions:

Refer to the Location Measurement Unit (LMUB) product documentation for

troubleshooting information.

Cancelling





448 DN998797


Id:0900d80580804c95

Confidential

8273 LICENCE FOR 2G FLEXI ABIS OVER IP/ETH-ERNET IS NOT AVAILABLE

214 8273 LICENCE FOR 2G FLEXI ABIS OVER

IP/ETHERNET IS NOT AVAILABLE

Meaning












component

5 the number of the Q1 service channel in the BSC, 0...27.


is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot




DN998797 449

Transmission Equipment Alarms (8000-8999) 8273 LICENCE FOR 2G FLEXI ABIS OVER IP/ETH-ERNET IS NOT AVAILABLE

Id:0900d80580804c95

Confidential


Instructions












Description: Transmission is commissioned to be in Pseudowire

(PWE) mode without a licence or without configuring the BSC.

Instructions:

1. Check the status of the '2G Flexi Abis over IP/

Ethernet' feature at the BSC, and if needed, install

and/or activate it.

2. Configure the '2G Flexi Abis over IP/Ethernet' feature

in the BSC.

Alternatively, you can:

1. Recommission the site to use TDM mode.

Cancelling





450 DN998797


Id:0900d80580804c95

Confidential

8274 LICENCE FOR 2G FLEXI ADDITIONAL 2 E1/T1IS NOT AVAILABLE

215 8274 LICENCE FOR 2G FLEXI ADDITIONAL 2

E1/T1 IS NOT AVAILABLE

Meaning












component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot




DN998797 451

Transmission Equipment Alarms (8000-8999) 8274 LICENCE FOR 2G FLEXI ADDITIONAL 2 E1/T1IS NOT AVAILABLE

Id:0900d80580804c95

Confidential


Instructions







To clarify the reason for the fault, open a remote session to

the transmission equipment and display the fault information.




Description: The number of used E1/T1 interfaces with terminated

Abis traffic is higher than the number of licensed E1/T1 interfaces

or the number of the E1/T1 interfaces configured in the BSC.

Instructions:

1. Check the status of the '2G Flexi Additional 2 E1/T1'

feature at the BSC, and if needed, install and/or activate

it.

2. Configure the '2G Flexi Additional 2 E1/T1' feature by

increasing the number of licensed E1/T1 interfaces at the

BSC.


1. Reduce the number of E1/T1 interfaces exceeding the licence:

a. Remove the terminated Abis allocations from the number of

exceeded interfaces.

OR

b. Set the exceeded number of interfaces to 'Not in Use'

state.

Note: Only two E1/T1 interfaces are licence free. One licence will

increase the number of E1/T1 interfaces by two.

Cancelling





452 DN998797


Id:0900d80580804c95

Confidential

8275 LICENCE FOR 2G FLEXI ABIS TRS GROOM-ING IS NOT AVAILABLE

216 8275 LICENCE FOR 2G FLEXI ABIS TRS

GROOMING IS NOT AVAILABLE

Meaning












component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot




DN998797 453

Transmission Equipment Alarms (8000-8999) 8275 LICENCE FOR 2G FLEXI ABIS TRS GROOM-ING IS NOT AVAILABLE

Id:0900d80580804c95

Confidential


Instructions







To clarify the reason for the fault, open a remote session to

the transmission equipment and display the fault information.




Description: Bypass cross-connections are configured in used E1/T1

interfaces without a licence or without configuring the BSC.

Instructions:

1. Check the status of the '2G Flexi Abis TRS Grooming'


it.

2. Configure the '2G Flexi Abis TRS Grooming' feature

in the BSC.


1. Disable all the cross-connections which are controlled by

'2G Flexi Abis TRS Grooming'.

Note: Bi-directional cross-connections controlled by '2G Flexi Abis

TRS Grooming' are of the following granularities: 8 kBit/s,

16 kBit/s, 32 kBit/s, 64 kBit/s and n*64 kBit/s.

Cancelling





454 DN998797


Id:0900d80580804c95

Confidential

8276 LICENCE FOR 2G FLEXI TRS LOOP PROTEC-TION IS NOT AVAILABLE

217 8276 LICENCE FOR 2G FLEXI TRS LOOP

PROTECTION IS NOT AVAILABLE

Meaning












component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot




DN998797 455

Transmission Equipment Alarms (8000-8999) 8276 LICENCE FOR 2G FLEXI TRS LOOP PROTEC-TION IS NOT AVAILABLE

Id:0900d80580804c95

Confidential


Instructions












Description: Abis protection and/or protected cross-connections are

configured in used E1/T1 interfaces without a licence or without

configuring the BSC.

Instructions:

1. Check the status of the '2G Flexi TRS Loop Protection'


it.

2. Configure the '2G Flexi TRS Loop Protection' feature in

the BSC.


1. Disable all cross-connections which are controlled by

'2G Flexi TRS Loop Protection'.

Note: Protected bi-directional cross-connections, Masked

bi-directional cross-connections and Abis protection are

controlled by '2G Flexi TRS Loop Protection'.

Cancelling




456 DN998797


Id:0900d80580804c95

Confidential

8277 ETHERNET PHYSICAL LINK LAYER LOST

218 8277 ETHERNET PHYSICAL LINK LAYER

LOST

Meaning

Incoming ethernet link connectivity is lost because of a broken or

missing cable, loose connector, or high attenuation on ethernet link.











component


be 0...27. If the equipment is supervised by the BTS, the channel number is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






DN998797 457

Transmission Equipment Alarms (8000-8999) 8277 ETHERNET PHYSICAL LINK LAYER LOST

Id:0900d80580804c95

Confidential



Instructions












Description: Physical Ethernet link is detected to be down.

Instructions:

1. Check that the Ethernet cable is connected to the right interface and

the cable is correctly mated to the PIU. Check the condition of

cables and connectors. Check that the length/type of the cable does not

introduce excessive attenuation.

2. Check that the device connected to the FIxx PIU supports 100 Base-T,

full duplex mode and autonegotiation.

3. Check that the device connected to the FIxx PIU has correct settings,

such as autonegotiation and Ethernet interface enabled.

4. Replace FIxx.

Cancelling





458 DN998797


Id:0900d80580804c95

Confidential

8278 PSEUDOWIRE DOWN

219 8278 PSEUDOWIRE DOWN

Meaning

Pseudowire connection is lost. There is a configuration mismatch ofpseudowire (PW) parameters between pseudowire emulation edge to edge

(PWE) near and far end, or a cut in connection in the packet switched

network because of a link/equipment defect or very high congestion.











component






the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 459

Transmission Equipment Alarms (8000-8999) 8278 PSEUDOWIRE DOWN

Id:0900d80580804c95

Confidential

FF = not defined



Instructions







To clarify the reason for the fault, open a remote session to thetransmission equipment and display the fault information.




Description: The incoming pseudowire connection is down. There is a fault

in the connection of the pseudowire. R bit is set at the CESoPSN control

word and sent in the Tx direction.

Instructions:

1. Check the pseudowire and pseudowire tunnel configuration settings at

both ends.

2. Check the conditions in the transmission path of the pseudowire tunnel

at the packet switched network.

3. Replace FIxx.

Cancelling





460 DN998797


Id:0900d80580804c95

Confidential

8279 PSEUDOWIRE PERFORMANCE DEGRADED

220 8279 PSEUDOWIRE PERFORMANCE

DEGRADED

Meaning

The performance of pseudowire is below the threshold. There is high

delay, delay variation, or excessive packet loss because of high load

in the packet switched network. The jitter buffer size is insufficient.











component

5 the number of the Q1 service channel in the BSC. The number can be 0...27. If the equipment is supervised by the BTS, the channel




the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 461

Transmission Equipment Alarms (8000-8999) 8279 PSEUDOWIRE PERFORMANCE DEGRADED

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Cancelling





462 DN998797


Id:0900d80580804c95

Confidential

8280 PSEUDOWIRE REMOTE PACKET LOSS

221 8280 PSEUDOWIRE REMOTE PACKET LOSS

Meaning

The far-end pseudowire emulation edge to edge (PWE) equipment signalsare defect in the received pseudowire (PW) signal of the far-end PWE

equipment. There is a PW parameter configuration mismatch between the

PWE near and far end, a unidirectional cut in connection in the packet

switched network because of a link/equipment defect, or very high

congestion.











component






the alarm printout.






FF = not defined



9 shelf number

FF = not defined





DN998797 463

Transmission Equipment Alarms (8000-8999) 8280 PSEUDOWIRE REMOTE PACKET LOSS

Id:0900d80580804c95

Confidential

10 slot

FF = not defined



Instructions












Description: Signalled by the equipment in the far-end; indicates a

serious fault in the received signal at the far-end equipment.

Instructions:

1. Check for alarms at the far-end equipment. See instructions on them.

2. Check the condition of the cables and connectors, and the correct

polarities of the wire pairs at both ends.

3. Check that the pseudowire and pseudowire tunnel settings are correct

at both ends.

4. Check the transmission path of the pseudowire tunnel from the alarming

interface to the far end.

Cancelling





464 DN998797


Id:0900d80580804c95

Confidential

8281 FAULT IN OPTICAL INTERFACE (SFP)

222 8281 FAULT IN OPTICAL INTERFACE (SFP)

Meaning

A fault has been detected on the ethernet SFP interface. The insertedSFP module type is not supported, the inserted SFP module type could

not be identified, or there is a SFP module signals fault in the

transmitter.











component






the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot



DN998797 465

Transmission Equipment Alarms (8000-8999) 8281 FAULT IN OPTICAL INTERFACE (SFP)

Id:0900d80580804c95

Confidential

FF = not defined



Instructions










Flexi EDGE Flexi Multiradio:

Description: A fault is detected at the Ethernet SFP interface.

Instructions:

1. Check that the SFP module is correctly installed.

2. Check that the SFP module is of supported type (Ethernet 1000 Base-SX

or 1000 Base-LX).

3. Check that the electrical contacts of the SFP module are clean from

dust, dirt or water.

4. Replace the SFP module.

5. Replace FIxx.

Cancelling





466 DN998797


Id:0900d80580804c95

Confidential

8282 PSEUDOWIRE TUNNEL DOWN

223 8282 PSEUDOWIRE TUNNEL DOWN

Meaning

Pseudowire tunnel is not functional. No pseudowire packets have arrivedfor the configured VLAN and pseudowire local/peer IP address pair for

one second.

Possible causes are that there are no pseudowires configured on the

peer IP, the local or peer IP/gateway configurations are incorrect,

the peer subnet mask is incorrect, the far-end ARP resolution for the

local IP address has failed, the VLAN configuration is incorrect, or

there is no physical connection.











component






the alarm printout.




the alarm printout.



FF = not defined



9 shelf number



DN998797 467

Transmission Equipment Alarms (8000-8999) 8282 PSEUDOWIRE TUNNEL DOWN

Id:0900d80580804c95

Confidential

FF = not defined



10 slot

FF = not defined



Instructions







To find out the reason for the fault, open a remote session to the




Flexi EDGE Flexi Multiradio:

Fault reason: Transmission is commissioned to be in Pseudowire (PWE)

mode without a licence.

Instructions:

1. Install and activate the 'Flexi EDGE Abis over IP/

Ethernet' licence at the BSC.

2. Recommission the site to use TDM mode.

Cancelling





468 DN998797


Id:0900d80580804c95

Confidential

8283 LICENCE FOR IP SECURITY IS NOT AVAIL- ABLE

224 8283 LICENCE FOR IP SECURITY IS NOT

AVAILABLE

Meaning







3 the functional entity number specifies a physical

unit of the transmission equipment, for example a

plug-in unit or a daughter board. The number can be

0...254

4 the supervision block number specifies the faulty

part of the functional entity, for example a certain

line interface or component





the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






DN998797 469

Transmission Equipment Alarms (8000-8999) 8283 LICENCE FOR IP SECURITY IS NOT AVAIL- ABLE

Id:0900d80580804c95

Confidential



Instructions











Cancelling

Do not cancel the alarm. The system cancels the alarm automatically

when the fault has been corrected.



470 DN998797


Id:0900d80580804c95

Confidential

8284 TRAFFIC SHAPING MISCONFIGURATION

225 8284 TRAFFIC SHAPING MISCONFIGURA-

TION

Meaning

Traffic shaping misconfigured. BTS-internal traffic shaping disabled but

Abis traffic shaping is enabled or CIR value of Abis traffic shaping is

smaller than CIR value of the BTS-internal uplink traffic shaping.








0...254








the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






DN998797 471

Transmission Equipment Alarms (8000-8999) 8284 TRAFFIC SHAPING MISCONFIGURATION

Id:0900d80580804c95

Confidential



Instructions










The fault code and corrective actions.

Cancelling





472 DN998797


Id:0900d80580804c95

Confidential

8285 LICENCE FOR TIMING OVER PACKET IS NOT AVAILABLE

226 8285 LICENCE FOR TIMING OVER PACKET

IS NOT AVAILABLE

Meaning










0...254


part of the functional entity, for example a

certain line interface or component





the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






DN998797 473

Transmission Equipment Alarms (8000-8999) 8285 LICENCE FOR TIMING OVER PACKET IS NOT AVAILABLE

Id:0900d80580804c95

Confidential



Instructions











Cancelling


when the fault has been corrected. Alarm is cancelled when the

license for ToP clock is made available or Alarm is cancelled when

ToP clock is removed from the priority list.



474 DN998797


Id:0900d80580804c95

Confidential

8286 LICENCE FOR SYNCHRONOUS ETHERNET ISNOT AVAILABLE

227 8286 LICENCE FOR SYNCHRONOUS

ETHERNET IS NOT AVAILABLE

Meaning










0...254








the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined






DN998797 475

Transmission Equipment Alarms (8000-8999) 8286 LICENCE FOR SYNCHRONOUS ETHERNET ISNOT AVAILABLE

Id:0900d80580804c95

Confidential



Instructions











Cancelling


when the fault has been corrected. Alarm is cancelled when the

license for SyncE clock is made available or Alarm is cancelled when

SyncE clock is removed from the priority list.



476 DN998797


Id:0900d80580804c95

Confidential

8287 CLOCK RECOVERY IN PROGRESS

228 8287 CLOCK RECOVERY IN PROGRESS

Meaning

BTS Timing over Packet Slave is running clock recovery algorithm andclock synchronisation is not yet complete








0...254

4 the supervision block number specifies the

faulty part of the functional entity, for example

a certain line interface or component


If equipment is supervised by the BTS, the channel



Not included if the name is in the alarm object

field of the alarm printout.



Not included if the index is in the alarm object

field of the alarm printout.



FF = not defined Included only if the equipment is supervised

by a BTS that supports coordinate settings

9 shelf number

FF = not defined

Included only if the equipment is supervised

by a BTS that supports coordinate settings

10 slot

FF = not defined

Included only if the equipment is supervised by



DN998797 477

Transmission Equipment Alarms (8000-8999) 8287 CLOCK RECOVERY IN PROGRESS

Id:0900d80580804c95

Confidential

a BTS that supports coordinate settings

Instructions

Check Supplementary information field 1 to see whether

the BSC or the BTS supervises the equipment.

If the BSC supervises the equipment, use the MML commands

Axx for alarm administration.

If the BTS supervises the equipment, use the MML commands

EOx for alarm administration.



See the equipment operating manual for more detailed

information on the fault code and corrective actions.

Cancelling


when the fault has been corrected. Alarm is cancelled after ToP

clock gets the lock or Alarm is cancelled when 30 minute timer

expires. Alarm Error in Connection with ToP Master is raised and ToP

Clock is marked as Not OK.



478 DN998797


Id:0900d80580804c95

Confidential

8288 FAULT IN CONNECTION TO CLOCK MASTER

229 8288 FAULT IN CONNECTION TO CLOCK

MASTER

Meaning

Timing over Packet master is not reachable or unable to

provide required synchronisation messages

Notes: This alarm is masked if Loss of Synchronisation or Frequency error alarm is

raised.

Rationale is that if BTS switches to internal clock, there will be already these

alarms and user can determine if ToP is root cause by checking related status

display.

The alarm is raised when:1. The difference between expected sync message rate and

actual sync message rate is less than 50% within 10 seconds.

2. If the announce grant from the master is ignored for the first time after a

timeout period of 2 seconds.






unit of the transmission equipment, for example a plug-in unit or a daughter board. The number can

be 0...254






is not relevant



the alarm printout.




the alarm printout.






DN998797 479

Transmission Equipment Alarms (8000-8999) 8288 FAULT IN CONNECTION TO CLOCK MASTER

Id:0900d80580804c95

Confidential


9 shelf number

FF = not defined



10 slot

FF = not defined



Instructions

Check Supplementary information field 1 to see whether

the BSC or the BTS supervises the equipment.









Cancelling


when the fault has been corrected. Alarm is cancelled when ToP Clock

gets the lock or ToP Clock is removed from priority list.



480 DN998797


Id:0900d80580804c95

Confidential

8289 SSM HAS LOST TRACEABILITY TO PRCCLOCK SOURCE

230 8289 SSM HAS LOST TRACEABILITY TO PRC

CLOCK SOURCE

Meaning

Invalid clock quality level received

Notes: This alarm is masked if Loss of Synchronisation or Frequency error alarm is

raised.

Rationale is that if BTS switches to internal clock, there will be already these

alarms and user can determine if SSM is root cause by checking related status

display.










component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined




DN998797 481

Transmission Equipment Alarms (8000-8999) 8289 SSM HAS LOST TRACEABILITY TO PRCCLOCK SOURCE

Id:0900d80580804c95

Confidential

10 slot

FF = not defined



Instructions











Cancelling



Alarm is cancelled if SSM Operation is disabled or Alarm is

cancelled if SyncE Clock is deleted from Priority list or Alarm is

cancelled if SSM with QL PRC is received at the active SyncE port.



482 DN998797


Id:0900d80580804c95

Confidential

8290 LICENCE FOR PACKET TRS E1/T1 IS NOT AVAILABLE

231 8290 LICENCE FOR PACKET TRS E1/T1 IS

NOT AVAILABLE

Meaning







3 the functional entity number specifies a physical unit

of the Transmission equipment, for example a plug-in

unit or a daughter board. The number can be 0...254

4 the supervision block number specifies the faulty part

of the Functional entity, for example a certain line

Interface or component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot




DN998797 483

Transmission Equipment Alarms (8000-8999) 8290 LICENCE FOR PACKET TRS E1/T1 IS NOT AVAILABLE

Id:0900d80580804c95

Confidential


Instructions

Check Supplementary information field 1 to see whether the

BSC or the BTS supervises the equipment.









Cancelling

Do not cancel the alarm. The system cancels the alarm

automatically when the fault has been corrected.



484 DN998797


Id:0900d80580804c95

Confidential

8291 PMTU BTS TO BSC LESS THAN CONFIGRUEDMTU

232 8291 PMTU BTS TO BSC LESS THAN CONFI-

GRUED MTU

Meaning

Path MTU (PMTU) to BSC has been determined by BTS to be less than the

configured MTU value.






of the transmission equipment, for example a plug-in

unit or a daughter board. The number can be 0...254


of the functional entity, for example a certain line

interface or component



is not relevant



the alarm printout.




the alarm printout.



FF = not defined



9 shelf number

FF = not defined



10 slot

FF = not defined




DN998797 485

Transmission Equipment Alarms (8000-8999) 8291 PMTU BTS TO BSC LESS THAN CONFIGRUEDMTU

Id:0900d80580804c95

Confidential


Instructions

Check Supplementary information field 1 to see whether the

BSC or the BTS supervises the equipment.





To clarify the reason for the fault, take a remote session

to transmission equipment and display fault information.



Cancelling

Do not cancel the alarm. The system cancels the alarm

automatically when the fault has been corrected.



Transmission Equipment Alarms (8000-8999)8292 PMTU BTS TO SECURITY GATEWAY LESSTHAN CONFIGURED MTU

233 8292 PMTU BTS TO SECURITY GATEWAY

LESS THAN CONFIGURED MTU

Meaning

Path MTU (PMTU) to Security Gateway has been determined by BTS

to be less than the configured MTU value.






of the transmission equipment, for example a plug-in unit

or a daughter board. The number can be 0...254


of the functional entity, for example a certain line

interface or component


2g 8000 - 8999 transmission alarms

Documents