2u brochure
TRANSCRIPT
MT-3000 , MT-7000CRDi Test Bench I-CRDI (MT-4500)
Functions□�CRDi Injector Test for Bosch, Delphi, Denso
(Siemens and Piezo types are also possible)□Injection- hole air suction function□Resistant Test□Injector Automatic Injection Test□Manual control function embedded
Specific characteristics and advantages□Diverse injection patterns are embedded□�Function to protect from short circuit, function to
protect from the overcurrent□�Function of automatic discharge of the injection
volume□�Injection time can be controlled up to 250us ~
2000us by 10us unit□�Shape of injection can be clearly confirmed by
atomization (Fog) fuel removal and LED lighting□�Changes the cleaning function flow rate and cleaning
with a lot of flow rate□�Able to check measurement of injection volume by
back leak
Specification of the Products□Product Name : I-CRDI□Model Name : MT-3000□Operation Status Display : 2 X 3FND, 9LED□Input Voltage : AC 110~220, MAX 300W□Output Signal : 2Ch. DC 60 ~170, MAX 450W□�Max. Allowable Pressure : 8bar Input, 7.5bar Pump
Pressurization□�Max. Discharge Pressure : 1000bar when test oil is
used□Injection count (Max. 990 rounds of injection test)□�Workable Temperature :
5~40 Degrees (Based on room temperature)□Weigh t : 65kgs□Size : 550 x 400 x 950
FunctionsResistant voltage test for 8 channels simultaneously□Gasoline & LPI Injector Diagnostic Test□�Automatic Transmission Solenoid Valve Diagnostic
Test□ISA□Electronic EGR Test
Specific characteristics and advantages□Solenoid Sensor Automatic Reading Function□Function to protect from short circuit□Function to protect from the overcurrent□Automatic distinction of coil damages□�Automatic Diagnosis Mode by each Pattern
embedded□�Removal of tar from LPI vehicles – Solves engine
discord and vibration of the vehicles□�Check and removal of set-in sludge inside the
solenoid valve – Improves shift shock and slip phenomenon
Specification of the Products□�Product Name : I-CLEAN□�Model Name : MT-7000□�Input Range : AC 100~200V MAX 450W□�Output Range : DC 0~12V MAX 300W□�Driving Channel : 8 Channels□�Workable Temperature: 0~80℃ (Based on room
temperature)□�Weight : 4.1Kgs□�Size : 330x370x250□�Configuration : Main body, Connector and Power
Cable
Multi-Purpose Solenoid Valve Diagnostor I-CLEAN (MT-7000)CRDi Injector Tester
Functions□Resistant test of the injector□Unit Injector Test (Bosch, Delphi, Denso –Siemens, Piezo)□High-pressure Pump Test□Rail Test
Specific characteristics and advantages□Precision control by PC□Full Automatic System (Automatic test sequence)□Manual control function embedded□Oil temperature control□Controls the injection time by 0.01ms unit□Control of voltage and current by each type of injectors□Automatic motor control system during measurement□IMV control function□Measured data saving function□Function to select the model names of injectors□Functions of automatic discharge and automatic receiving of injection volume
Specification of the Products□Product Name : I-CRDi□Model Name : MT-4500□Motor Output : 2.2Kw basic (3 H/P) , able to be upgraded up to 10 H/P□�Max. Pressure : 1350bar basic, able to use up to 2000bar
(When the high-pressure pump and rails are upgraded)□No. of rounds of injection : 10~999times (10 rounds unit)□Output: 4 Channels□Measured volume of the cylinder : 50cc, 100cc (Rail Back Leak)□Cooling : Forced cooling□Input Voltage : 380V 50/60Hz 3 Phase□220V 50/60Hz (Option)□Internal Voltage : 5/12V, 70~200V□Oil Control : Variable Type□Weight : 200Kgs□Size : 1100 x 540 x 1720
365-40, Hwajeong-dong, Seo-gu, Gwangju, South KoreaTel. +82-62-571-2828 Fax. +82-62-571-2829 www.2u-2u.com
Multi-Electric Current Tester for Vehicles(LEAK-B) Functions□Measurement of quiescent current from the vehicles
□Surveillance function of output from the generators□Battery test function□Voltage test
Specific characteristics and advantages□�Function to set warning sound : Warning sound shall be issued when
measuring the current exceeding the set value□Low voltage warning and circuit protection function□Convenient measurement through charging
Specification of the Products□Product Name: LEAK-B
□Model Name: MT-020□Electric Source Voltage: DC 10V ~ 24V□Measured Voltage: DC -25V ~ +25V□Measured Current: DC -25A ~ +25A
Introduction of the Company2U Co., Ltd. was established in 2002 as a company specializing in manufacturing of automobile tester, test equipments and the embedded systems.The company has been manufacturing the common-rail injector tester, multi-tester for vehicles and solenoid valve testers, which are being supplied to over 50 some auto maintenance equipment specialty stores in Korea.We promise to contribute to enhance competitiveness of our customers by improving the quality of our products with the continuous R&D activities and the accumulated human/technological know-how over the years in the future as well, and shall incessantly endeavor to reform as 2U in the world equipped with the global competitiveness and sparing no investment to job innovation and cultivation of human resources