2_un5000 upgrade procedure for r230(indsat)_3

SMS-600V UPGRADE PROCEDURE

Date: 29 Feb, 2008SpectralWave UN5000Procedures to Upgrade FirmwareNEC Corporation

Carrier Network Business Unit

Broadband Network Operations Unit

Optical Network DivisionTable of Contents32. TARGET PACKAGES AND THEIR FIRMWARE VERSIONS

43. WORK FLOW

54. PREPARATION

65. NEED-TO-KNOW THINGS

65.1 Precaution

65.1.1 Upgrading Procedures

85.2 Record the Current Condition

96. UPGRADING PROCEDURES

96.1 Install Bundle Files into INC-100MS Server

126.2 Verify Installed Firmware Version

186.3 Download Bundle Files (EXTWB)

216.4 Verify Downloaded Files (EXTWB)

246.5 Cutover and Swap (EXTWB)

316.6 Verify Results of Cutover and Swap Operations (EXTWB)

346.7 Download Bundle Files (EXT16)

376.8 Verify Downloaded Files (EXT16)

406.9 Cutover and Swap (EXT16)

476.10 Verify Results of Cutover and Swap Operations (EXT16)

506.11 Download Bundle File (Main: Rel. 2.30 AGENT)

536.12 Verify Downloaded Files (Main: Rel. 2.30 AGENT)

556.13 Cutover and Swap (Main: Rel. 2.30 AGENT)

626.14 Verify Cutover and Swap Operations (Main: Rel. 2.30 AGENT)

646.15 Download Bundle File (Main: Rel. 2.30 SC/FC)

676.16 Verify Downloaded Files (Main: Rel. 2.30 SC/FC)

696.17 Cutover and Swap (Main: Rel. 2.30 SC/FC)

766.18 Verify Cutover and Swap Operations (Main: Rel. 2.30 SC/FC)

787. Verify Conditions

79Appendix: Procedures to Add Extension Shelves

791. Set Lockout

822. Register Extension Shelf

833. Release Lockout

INTRODUCTIONThis document describes how to upgrade the version of SpectralWave U5000, using INC-100MS. 1. INTENDED USAGE OF THIS DOCUMENT1). Customer:INDSAT

2). Target equipment:UN5000 (MAIN, EXT16, EXTWB)3). Original version (current):Rel. 2.10 (MAIN), Rel. 2.10 or U-Node version (EXT16 / EXTWB)4). Target version:Rel. 2.30 (MAIN)Rel. 2.30 (EXT16 / EXTWB)2. TARGET PACKAGES AND THEIR FIRMWARE VERSIONSFollowing table (Table 1) lists the firmware versions of packages for each Release:

PKG CodePKG NameCurrent Version

(Rel.2.10 or U-Node)New Version

(Rel.2.30 after)

NWA-009625-001MSCMSC02.1702.70

AGENT(OSI)01.3102.01

NWA-009625-001MSCMSC02.1702.70

AGENT(TCP/IP)02.0002.51

NWA-009628-002SSCMSW02.1202.35

OHC02.0702.32

NWA-010275-0B0

EXT CLK:2MHzMX320LE02.1702.37

NWA-010275-0C0

EXT CLK:2MB/s

NWA-009643-002S64P01.3202.05

NWA-009646-001S16P01.3202.05

NWA-016119-0A3SC16M52.0354.00

E32-001-UB274-xxxxSSC10.01 or U-Node Version10.01

E32-001-UB478-xxxxOHCEXT08.22 or U-Node Version51.00

E32-465-UB279-xxxxESW51.03 or U-Node Version51.03

E32-852-UB283-****SINFM51.00 or U-Node Version51.00

E32-852-UB282-****SINF1651.00 or U-Node Version51.00

E32-484-UB287-****STM1E51.00 or U-Node Version51.00

E32-484-UC876-****GBPRU-Node Version51.00

E32-001-UB558-****SCWB252.0253.00

E32-001-UB560-****SSCWB11.01 or U-Node Version11.01

E32-465-UB561-****PSW5WB51.00 or U-Node Version51.00

E32-465-UB562-****PSW10WB51.00 or U-Node Version51.00

E32-484-UB563-xxxxE1251.00 or U-Node Version51.01

E32-484-UC875-1***EINFMU-Node Version52.00

3. WORK FLOW

4. PREPARATIONVerify that following materials are ready for the procedures:1) Procedures to Upgrade Firmware:1 SpectralWave UN5000 AMP64 Setup Procedures (required before Firemware upgrade)2 This document* Before proceeding to this document, 1 SpectralWave UN5000 AMP64 Setup Procedures (required before Firemware upgrade) must be completed.2) F/W Bundle files (CD ROM):# Bundle file for UN5000 Rel.2.30(A0230011.UN2,A0230014.UN2,A0230015.UN2, A0230016.UN2, C0230011.UN2, C0230M11.SUW ( 1-set containing 6 files)3) CID Software (CD ROM):# CID file for UN5000 Rel.2.30

4) When newly adding EXT16/EXTWB Shelf to UN5000 Main Shelf while in service, proceed with the following: When Using EXT16/EXTWB of UN5000: Complete all the physical connections to the UN5000 by referring to the SpectralWave( UN5000 User's Manual (DOI-S11641).

Referring to Appendix: Procedures to Add Extension Shelves, register EXT16/EXTWB Shelf by INC-100MS and CID.

Ensure to release the Lockout state, which is provided in Appendix: Procedures to Add Extension Shelves, Chapter 3. Release Lockout When Using EXT16/EXTWB of U-Node BBM:If using EXT16/EXTWB Shelf/Shelves of U-Node BBM, proceed with the follwoing in advance:

Prepare and install the appropriate SC16M or SCWB2 that is for the use of UN5000.

Complete all the physical connections to the UN5000 by referring to the SpectralWave( UN5000 User's Manual (DOI-S11641).

Referring to Appendix: Procedures to Add Extension Shelves, register the EXT16/EXTWB Shelf by INC-100MS and CID.Ensure to release the Lockout state, which is provided in Appendix: Procedures to Add Extension Shelves, Chapter 3. Release Lockout When Upgrading F/W Versions by CID:To upgrade UN5000 F/W versions by CID, refer to the SpectralWave( UN5000 User's Manual (DOI-S11641) for its operation.5. NEED-TO-KNOW THINGS!! Ensure to Read Following BEFORE Starting Procedures !!

5.1 Precaution

5.1.1 Upgrading ProceduresThe upgrading procedures here include a Cutover operation. Using downloaded files, the Cutover operation reboots the NE, which updates the NE. Since following events will occur when an NE is restarted, obtaining approvals of the customer is required in advance. Traffic Interruption on EINFM Package. During the Cutover operation, all the traffic associated with the target EINFM Package are interrupted. EINFM that is upgraded by this procedure supports LCAS function.*EINFM Package that supports LCAS function does not associate with the one on the other end if it does not support LCAS function, where all the traffic associated with those EINFM is interrupted. To proceed with this upgrades, EINFM on the other end must be either the one that supports LCAS or that is to be upgraded to support LCAS.Traffic Interruption on E12 Package.

A cutover operation interrupts the traffic associated with E12 packages.

Saved PM data will Be Cleared. An NE has saved PM data of each facility, path end of a node, including IPPM, which will be erased by rebooting the NE. When the NE is started up again, it newly starts counting the PM data that are to be saved.Saved Command Logs will Be ClearedAn NE has saved logs of all commands issued to the NE, which will be erased by rebooting the NE. Logs of commands that are issued after the NE is restarted will be saved.Saved Automatic-Report Logs will Be ClearedAn NE has saved logs of automatic reports that the NE has made, which will be erased by rebooting the NE. Logs of automatic reports that are made after the NE is restarted will be saved.Brief Interruption of Communication with INC-100MSWhile proceeding with procedures here, Association Fail alarm occurs to the target NE temporarily, and DCC-LINK-FAIL occurs to the associated node. It may take about 10 minutes to recover from the occurrence of these conditions.Brief Interruption of Communication with EXTWB Shelf

While proceeding with procedures here, LINK_FAIL_EXT alarm occurs to the target NE temporarily if EXT16/EXTWB shelf is connected. It may take about 10 minutes to recover from the occurrence of this condition.No other events affected by the procedures should occur.

>1) Do not attempt CID operation while the procedures are done by INC-100MS.2) Do not attempt controlling/operating NEs associated with the target NE in the Ring network during the Cutover operation.3) When the target equipment enables the following protection functions, ensure that their WORK sides are in service; Do not perform this procedure if a PROTECTION side is selected. Package Protection Line Protection Path Protection Ring Protection[If any events or difficulties other than those mentioned above occur during the procedures, contact NEC.]

5.2 Record the Current Condition

Before starting the procedures, record the current conditions of the network, which should be the same as those obtained after the upgrade.

StepWork DescriptionsItems to VerifyCheck

01Open the New Event Window of the INC-100MS (Fig. 1), and check the current alarms and conditions.

Left-click on the New Event-box

-> New Event Window Opens

Dont close this New Event Window, until complete whole procedure.* To use an extension shelf of U-Node BBM, replace SC16/SCWB2 with SC16M/SCWB2 provided for UN5000, and complete all the physical connections to UN5000 referring to the UN5000 User's Manual. Registrations of the shelf must be completed by INC-100MS on ahead. (Refer to Appendix: Procedures to Add Extension Shelves chapter.)1) No alarm is occurring.

2) If an alarm is occurring, judge whether or not the upgrading procedure is available to keep going. If necessary, ask the customer for the judgment.

3) For the record, save the New Event data by a screen copy for the use of verification after the work.

* If a target PKG to be upgraded is in abnormal condition (IMPROPRMVL, CPU_FAIL and/or PKG_FAIL), the download will not be properly completed, or the traffic may be affected at the Cutover.

* When using an extension shelf of U-Node BBM, an SFT_VER alarm will be issued to the package on the extension shelf. However, this alarm does not affect the procedure for upgrading F/W versions.

Fig. 1: New Event Window

# End of Record the Current Condition procedure.

6. UPGRADING PROCEDURES

6.1 Install Bundle Files into INC-100MS ServerThe bundle files should be stored in INC-100MS Server. Follow the procedure to install them.


01Open the Firmware Install dialog box. (Fig. 2)Click Configuration -> Maintenance -> Firmware InstallSelect the target Server to which the bundle files are installed.Firmware Install window. (Fig. 2)

Fig. 2: Firmware Iinstall Window

02Place the CD-ROM containing the bundle files into the CD drive of the Client PC.CD-ROM (see 4. Preparation for appropriate CD-ROMs.)


03Click Refer button and select the bundle file to be downloaded (For Rel2.30). (Fig. 3)Select A0230014.UN2.

Fig. 3: Select Bundle File

04From the Server List, select the target server to which the bundle files are installed. (Fig. 4)--

Fig. 4: Select Bundle File

05Click Action button. (Fig. 4)Confirmation message appears. (Fig. 5)


06Click Yes to download them. (Fig. 5)---

Fig. 5: Confirmation Message

07When completed, a massage appears in the margin of Firmware Install dialog box. (Fig. 6)

Fig. 6: Message on Firmware Install Dialog Box

08Repeat Steps 03 thru 07 to install the remaining bandle files (see below):Target bundle files: A0230015.UN2A0230016.UN2A0230011.UN2C0230011.UN2C0230M11.SUW

09Click Close button to close the Firmware Install dialog box.---

# End of Install Bundle Files into INC-100MS Server procedure.

6.2 Verify Installed Firmware VersionRelease version of a target node should be confirmed before downloading the firmware.

StepWork DescriptionItems to VerifyCheck

01Left-click to select the target node whose current firmware version is to be checked.

Then, right-click to show the menu, and select Detail Setup. (Fig. 7)CID+ window appears.

Fig. 7: Select Detail Setup

02Open Inventory dialog box. (Fig. 8)

Click Reports -> Inventory.Inventory dialog box appears. (Fig. 9)

Fig. 8: CID+ Window


03Click List tab and scroll the sheet to the right to display Secondary column.---

Fig. 9: Inventory Dialog Box

04Active column lists the firmware version of each PKG that is currently used for operation. Verify the versinos indicated in the Active column and those listed in Table 1. Applicable F/W Versions.Check the release versions used by the target node.If the target node has any firmware whose version belongs to neither equipment release,Rel. 2.10, contact NEC.

05Close the Inventory dialog box when the firmware versions are verified. ---


06Open Extension shelf Access dialog box (Fig. 10).Click Operation-> Extension shelf Access.

Click EXTWB Tab and Click OK.Extension shelf Access dialog box appears. (Fig. 11)

Fig. 10: CID+ Window







09Active column lists the firmware version of each PKG that is currently used for operation. Verify the versinos indicated in the Active column and those listed in Table 1. Applicable F/W Versions.Check the release versions used by the target node.

If the target node has any firmware whose version belongs to neither equipment release, Rel. 2.10 or U-Node version, contact NEC.

10Close the Inventory dialog box when the firmware versions are verified.---

11When more than one EXTWB Shelf is connected,perform Step 06 through 10 to each EXTWB shelf.---


12Open Extension shelf Access dialog box (Fig. 13).Click Operation-> Extension shelf Access.

Click EXT16 Tab and Click OK.Extension shelf Access dialog box appears. (Fig. 14)








15Active column lists the firmware version of each PKG that is currently used for operation. Verify the versinos indicated in the Active column and those listed in Table 1. Applicable F/W Versions.Check the release versions used by the target node.

If the target node has any firmware whose version belongs to neither equipment release, Rel. 2.10 or U-Node version, contact NEC.

16When more than one EXT16 Shelf is connected,perform Step 12 through 15 to each EXT16 shelf.---

17Close the Inventory dialog box and CID+ window when the firmware versions are verified. ---

# End of Verify Installed Firmware Version procedure.6.3 Download Bundle Files (EXTWB)

To proceed with steps here, installations of all required bundle files into the INC-100MS Sever must be completed.


01Select an equipment type of the target node (Fig. 16).Click Configuration -> Maintenance -> Firmware Download -> UN5000NE Select Firmware Download dialog box appears. (Fig. 17)

Fig. 16: Select Equipment Type

02From the NE Select Firmware Download dialog box, select the target node, and click the Select button. (Fig. 17)Firmware Download dialog box to select a file appears. (Fig. 18)

Fig. 17: NE Select - Firmware Download


03Select the bundle file for EXTWB. (Fig. 18)Bundle file for EXTWB: C0230M11.SUW

04Click Download button. (Fig. 18)Confirmation dialog box appears. (Fig. 19)

Fig. 18: Select the Bundle File

05Click OK to start downloading. (Fig. 19)While in downloading process, State of progress indicator (Fig. 20) appears.


Fig. 20: State of Progress Indicator

ItemWork descriptionConfirmation itemCheck

06Upon the completion of the download, the information message (Fig. 21) pops up. Click OK and Close button to end the session.< If an error message appears >

# Redo Steps 01 thru 05.

# If another trial also fails, contact NEC.

Fig. 21: Completion of Download

# End of Download Bundle Files (EXTWB) procedure.

6.4 Verify Downloaded Files (EXTWB)

When the bundle file download is completed, check if the bundle files are downloaded properly by comparing with those in the secondary memories.


01Left-click to select the target node.

Then, right-click on the node to show the menu (Fig. 22), and select Detail Setup.CID+ window appears.



02Open Extension shelf Access dialog box (Fig. 23).

Click Operation -> Extension shelf Access.Click EXTWB Tab and Click OK.Extension shelf Access dialog box appears. (Fig. 24)



Click Reports -> Inventory.Inventory (Fig. 25) dialog box appears.



04Click List tab, then scroll the sheet to the right to display Secondary column.---

Fig. 25: Inventory - List Dialog Box

05Check if indications for Active, Primary, Secondary columns match to those listed in the version table below. Especially, the indication of Secondary column that shows the version of downloaded firmware at this point must be identical to that of the table below.

Dialog box above is an example. Packages displayed in the Inventory dialog box differ depending on packages acutally installed.

Confirmations are unnecessary for packages if unlisted below.

PKGActivePrimarySecondary

SCWB252.02 or 53.0052.02 or 53.0053.00

SSCWB11.01 or U-Node ver11.01 or U-Node ver11.01

PSW5WB/10WB51.00 or U-Node ver51.00 or U-Node ver51.00

E1251.00 or U-Node ver51.00 or U-Node ver51.01

>

# Redo 6.3 Download Bundle Files procedure.



07Close the Inventory dialog box and CID window when completed. ---

# End of Verify Downloaded Files (EXTWB) procedure.

6.5 Cutover and Swap (EXTWB)

When the downloaded files are verified, execute the Cutover operation to switch the use of files assigning new files in Secondary for Active, and Swap operation to swap the labels of Primary and Secondary.


01Select an equipment type of the target node (Fig. 26).

Click Configuration -> Maintenance -> Firmware Download -> UN5000NE Select Firmware Download dialog box appears. (Fig. 27)


02From the NE Select Firmware Download dialog box, select the target node for Cutover and Swap operations, and click the Select button. (Fig. 27)Firmware Download dialog box to select a file appears. (Fig. 28)



03Select a bundle file. (Fig.28)Bundle file for EXTWB: C0230M11.SUW

04Click Switch button. (Fig. 28)A dialog box for switch mode selection appears. (Fig. 29)

Fig. 28: Firmware Download Dialog Box

05From the Switch Mode options, select CutoverOnly, and click OK button. (Fig. 29)Confirmation message (Fig. 30) appears.

Fig. 29: Select the Switch Mode


06Confirm the indicated file listed for FileName, and then click OK to proceed. (Fig. 30)FileName: C0230M11.SUW


07While in progress, Firmware Download dialog box shows following message (Fig. 31).

While in this operation:

# LINK_FAIL_EXT alarm occurs to the target NE temporarily.

(It may take about 10 minutes to recover from the occurrences of these alarms.)

# If the status is not restored within 30 minutes, contact NEC.

Fig. 31: Excuting Cutover


08Following message (Fig. 32) appears. But cutover operations are not still completed, Wait till the Cutover operations are completed. (about 20 minutes; On the New Event window, LINK_FAIL_EXT alarm is cleared.)

Then click OK and Close button to end the session.If the operations are not completed properly displaying an error message, make a screen copy of the message, and submit it to NEC with the results of Procedure 6.6 Verify Results of Cutover and Swap Operations.

Fig. 32: Completion of Cutover Operations




10From the Switch Mode options, select MemswitchOnly, and click OK button. (Fig. 34)Confirmation message (Fig. 35) appears.



11Confirm the indicated file listed for FileName, and then click OK to proceed. (Fig. 35)FileName: C0230M11.SUW



Wait till the Swap (Memswitch) operations are completed.


Fig. 36: Excuting Swap


13When the Swap operations are completed, following message (Fig. 37) appears.

Click OK and Close button to end the session.If the operations are not completed properly displaying an error message, make a screen copy of the message, and submit it to NEC with the results of Procedure 6.6 Verify Results of Cutover and Swap Operations.

Fig. 37: Completion of Swap Operations

14Close dialog boxes.---

15Execute Cutover and Memswitch (=SWAP) to the target SSCWB using CID.

Refer to the SpectralWave( UN5000 Operation and Maintenance manual (DOI-07488) for those operatoin.

# End of Cutover and Swap (EXTWB) procedure.

6.6 Verify Results of Cutover and Swap Operations (EXTWB)When the Cutover and Swap operations are completed, the EXTWB of the target node now runs using the newly downloaded firmware. Perform this procedure to confirm that the node is running the new firmware.







Click Operation -> Extension shelf Access.Click EXTWB Tab and Click OK.Extension shelf Access dialog box appears. (Fig. 40)



Click Reports -> Inventory.Inventory (Fig. 41) dialog box appears.



04Click List tab and scroll the sheet to the right to display the Secondary column.---


05Check if indications for Active and Primary columns match to those listed in the version table below.Dialog box above is an example. Package displayed in the Inventory dialog box differ depending on packages actually installed.

Confirmations are unnecessary for packages if unlisted below.


SCWB253.0053.0052.02 or 53.00

SSCWB11.0111.0111.01 or U-Node ver

PSW5WB/10WB51.0051.0051.00 or U-Node ver

EINFM51.0151.0151.00 or U-Node ver

# Refer Table1 _Page3

>

# Contact NEC.


07Close the Inventory dialog box and CID window when completed.---

# End of Verify Results of Cutover and Swap Operations (EXTWB) procedure.6.7 Download Bundle Files (EXT16) To proceed with steps here, installations of all required bundle files into the INC-100MS Server must be completed.





02From the NE Select Firmware Download dialog box, select the target node, and click the Select button. (Fig. 43)Firmware Download dialog box to select a file appears. (Fig. 44)



03Select the bundle file for EXT16.Firmware for EXT16: C0230011.UN2

04Click Download button.Confirmation dialog box appears. (Fig. 45)


05Click OK to start downloading. (Fig. 45)While in downloading process, State of progress indicator (Fig. 46) appears.




06Upon the completion of the download, the information message (Fig. 47) pops up. Click OK and Close button to end the session.>


# If another trial also fails, contact NEC


# End of Download Bundle Files (EXT16) procedure.6.8 Verify Downloaded Files (EXT16)

After the bundle file download, confirm that the bundle files are downloaded properly by checking the secondary memory in packages. Follow the procedure to confirm the download result.







Click Operation -> Extension shelf Access.Click EXT16 Tab and Click OK.Extension shelf Access dialog box appears. (Fig. 50)






04Click List tab, then scroll the sheet to the right to display Secondary column.---


05Check if indications for Active, Primary, Secondary columns match to those listed in the version table below. Especially, the indication of Secondary colu,m that shows the version of downloaded firmware at this point must be identical to that of the table below.

Dialog box above is an example. Packages displayed in the Inventory dialog box differ depending on packages actually installed.

Confirmations are unnecessary for packages unlisted below.


SC16M52.03 or 54.0052.03 or 54.0054.00

OHCEXT08.22 or U-Node ver08.22 or U-Node ver51.00

SSC10.01 or U-Node ver10.01 or U-Node ver10.01

ESW51.03 or U-Node ver51.03 or U-Node ver51.03

SINFM/16/1E51.00 or U-Node ver51.00 or U-Node ver51.00

>

# Redo 6.7 Download Bundle Files (EXT16) procedure.



07When completed, close the Inventory dialog box and CID+ window. ---

# End of Verify Downloaded Files (EXT16) procedure.

6.9 Cutover and Swap (EXT16)






02From the NE Select Firmware Download dialog box, select the target node for Cutover and Swap operations, and click the Select button. (Fig. 53)Firmware Download dialog box to select a file appears. (Fig. 54)



03Select a bundle file. (Fig. 54)Bundle file for EXT16: C0230011.UN2

04Click Switch... button. (Fig. 54)A dialog box for switch mode selection appears. (Fig. 55)


05From the Switch Mode options, select CutoverOnly, and click OK button. (Fig. 55)Confirmation message (Fig. 56) appears.



06Confirm the indicated file listed for FileName, and then click OK to proceed. (Fig. 56)FileName: C0230011.UN2




# LINK_FAIL_EXT alarm occurs to the target NE temporarily. (It may take about 10 minutes to recover from the occurrences of these alarms.)




08Following message (Fig. 58) appears. But cutover operations are not still completed, Wait till the Cutover operations are completed. (about 20 minutes; On the New Event window, LINK_FAIL_EXT alarm is cleared.)






10From the Switch Mode options, select MemswitchOnly, and click OK button. (Fig. 60)Confirmation message (Fig. 61) appears.



11Confirm the indicated file listed for FileName, and then click OK to proceed. (Fig. 61)FileName: C0230011.UN2











# End of Cutover and Swap (EXT16) procedure.

6.10 Verify Results of Cutover and Swap Operations (EXT16)When the Cutover and Swap operations are completed, the EXT16 of the target node now runs with the newly downloaded firmware. Perform this procedure to confirm that the node is running the new firmware.







Click Operation -> Extension shelf Access.Click EXT16 Tab and Click OK.Extension shelf Access dialog box appears. (Fig. 66)







04Click List tab, and scroll the sheet to the right to display Secondary column.---


05Check if indications for Active and Primary columns match to those listed in the version table below.

Dialog box above is an example. Packages displayed in the Inventory dialog box differ depending on packages actually installed.Confirmations are unnecessary for packages if unlisted in the table below.


SC16M54.0054.0052.03 or 54.00

OHCEXT51.0051.0008.22 or U-Node ver

SSC10.0110.0110.01 or U-Node ver

ESW51.0351.0351.03 or U-Node ver

SINFM/16/1E51.0051.0051.00 or U-Node ver

# Refer to Table1 on Page3

>

# Contact NEC.


07When verified, close the Inventory dialog box and CID+ window.

# End of Verify Results of Cutover and Swap Operations (EXT16) procedure.6.11 Download Bundle File (Main: Rel. 2.30 AGENT)

To proceed with steps here, installations of all required bundle files into the INC-100MS Server must be completed.


01Select an equipment type of the target node youd like to download the bundle files.

Click Configuration -> Maintenance -> Firmware Download -> UN5000NE Select - Firmware Download dialog box (Fig. 69) appears.


02Select the target node, and click the Select button.Firmware Download dialog box to select a file (Fig. 70) appears.

Fig. 69: NE Select-Firmware Download

ItemWork DescriptionItems to VerifyCheck

03Select the bundle file.Bundle file for Main Rel. 2.30: A0230011.UN2

04Click Download button.Confirmation dialog box (Fig.71) appears.


05Click OK to start downloading.While in downloading process, State of progress idicator (Fig. 72) appears.




06Upon the completion of the download, the information message (Fig. 73) pops up. Click OK button to end the download session.>


# If another trial fails again, contact NEC.



# End of Download Bundle Files (Main: Rel. 2.30) procedure.6.12 Verify Downloaded Files (Main: Rel. 2.30 AGENT)

When the bundle files download is completed, check if the bundle files are downloaded properly by comparing with those in the Secondary memory.



Then, right-click on the node to show the menu, and select Detail Setup.Confirm that CID+ window (Fig. 75) appears.

Fig. 74: Detail Setup

02Open the Inventory dialog box:

Click Reports -> InventoryInventory dialog box (Fig. 76) appears.



03Click List tab, and scroll the sheet to the right to display Secondary column.--


04Check if indications for Active, Primary, Secondary columns match to those listed in the version table below. Especially, the indication of Secondary column that shows the version of newly downloaded firmware at this point must be identical to that of the table below.


Confirmations are unnecessary for packages if unlisted in the table below.


MSCM02.17(MSCM)02.1701.23

02.00(AGENT)02.0002.51

SSCM02.12(SW)02.1201.28

02.07(OHC)02.0701.23

MX320LE02.1702.1701.28

S64P01.3201.3201.23

S16P01.3201.3201.23

# Refer to Table1 on Page 3

>

# Redo the procedure in Section 6.11 Download Bundle Files (Main: Rel. 2.30).


05Close the Inventory dialog box and CID+ window when completed.

# End of Download Bundle File (Main: Rel. 2.30) procedure.6.13 Cutover and Swap (Main: Rel. 2.30 AGENT)



01Select an equipment type of the target node:



02Select the target node of Cutover and Swap operations.

Fig. 78: NE Select - Firmware Download Dialog Box


03Select the bundle file.Bundle file for Main (Rel. 2.30): A0230011.UN2

04Click Switch... button.A dialog box for switch mode selection appears (Fig. 80)


05From the Switch Mode options, select CutoverOnly, and click OK button.Confirmation message (Fig.81) appears.



06Confirm the indicated file listed for FileName, and then click OK to proceed.FileName: A0230011.UN2




# Association Fail alarm occurs to the target NE temporarily.# DCC-LINK-FAIL occurs to the opposing node associated with the target node.





08Following message (Fig. 83) appears. But cutover operations are not still completed, Wait till the Cutover operations are completed. (about 20 minutes; On the New Event window, Association Fail alarm is cleared.)

Then click OK and Close button to end the session.SFT_VER alarm will be issued to the package on the main shelf. However, this alarm does not affect the procedure for upgrading F/W versions.If the operations are not completed properly displaying an error message, make a screen copy of the message, and submit it to NEC with the results of Procedure 6.14 Verify Results of Cutover and Swap Operations.



09Click Switch button.A dialog box for switch mode selection appears. (Fig. 85)


10From the Switch Mode options, select MemswitchOnly, and click OK button.Confirmation message (Fig. 86) appears.














# End of Cutover and Swap Operations (Main: Rel. 2.30) procedure.6.14 Verify Cutover and Swap Operations (Main: Rel. 2.30 AGENT)

When the Cutover and Swap operations are completed, the Main shelf of the target node now runs using the new firmware. Perform this procedure to confirm that the node is running the new firmware.


01Left-click on the target node.

Then, right-click on the node to show the menu, and select Detail Setup. (Fig. 89)CID+ window (Fig. 90) appears.


02Open Inventory dialog box:

Click Reports -> Inventory (Fig. 90)Inventory dialog box (Fig. 91) appears.





04Check if indications for Active and Primary columns match to those listed in the version table below.Dialog box above is an example. Packages displayed in the Inventory dialog box differ depending on packages actually installed.



MSCM02.17(MSCM)02.1701.23

02.51(AGENT)02.5102.00

SSCM02.12(SW)02.1201.28

02.07(OHC)02.0701.23

MX320LE02.1702.1701.28

S64P01.3201.3201.23

S16P01.3201.3201.23

# Refer to Table 1 on Page 3.

>

# Contact NEC.

05When completed, close the Inventory dialog box and CID+ window.

# End of Verify Cutover and Swap Operations (Main: Rel. 2.30) procedure.6.15 Download Bundle File (Main: Rel. 2.30 SC/FC)

To proceed with steps here, installations of all required bundle files into the INC-100MS Server must be completed.


01Select an equipment type of the target node youd like to download the bundle files.



02Select the target node, and click the Select button.Firmware Download dialog box to select a file (Fig. 94) appears.

Fig. 93: NE Select-Firmware Download


03Select the bundle file.Bundle file for Main Rel. 2.30: A0230014.UN2

04Click Download button.Confirmation dialog box (Fig.95) appears.


05Click OK to start downloading.While in downloading process, State of progress idicator (Fig. 96) appears.




06Upon the completion of the download, the information message (Fig. 97) pops up. Click OK button to end the download session.>





# End of Download Bundle Files (Main: Rel. 2.30) procedure.6.16 Verify Downloaded Files (Main: Rel. 2.30 SC/FC)

When the bundle files download is completed, check if the bundle files are downloaded properly by comparing with those in the Secondary memory.



Then, right-click on the node to show the menu, and select Detail Setup.Confirm that CID+ window (Fig. 99) appears.


02Open the Inventory dialog box:

Click Reports -> InventoryInventory dialog box (Fig. 100) appears.





04Check if indications for Active, Primary, Secondary columns match to those listed in the version table below. Especially, the indication of Secondary column that shows the version of newly downloaded firmware at this point must be identical to that of the table below.




MSCM02.17(MSCM)02.1702.70

02.51(AGENT)02.5102.00

SSCM02.12(SW)02.1202.35

02.07(OHC)02.0702.32

MX320LE02.1702.1702.37

S64P01.3201.3202.05

S16P01.3201.3202.05

# Refer to Table1 on Page 3

>

# Redo the procedure in Section 6.15 Download Bundle Files (Main: Rel. 2.30).


05Close the Inventory dialog box and CID+ window when completed.

# End of Download Bundle File (Main: Rel. 2.30) procedure.6.17 Cutover and Swap (Main: Rel. 2.30 SC/FC)



01Select an equipment type of the target node:



02Select the target node of Cutover and Swap operations.

Fig. 102: NE Select - Firmware Download Dialog Box


03Select the bundle file.Bundle file for Main (Rel. 2.30): A0230014.UN2

04Click Switch... button.A dialog box for switch mode selection appears (Fig. 104)


05From the Switch Mode options, select CutoverOnly, and click OK button.Confirmation message (Fig.105) appears.







# Association Fail alarm occurs to the target NE temporarily.# DCC-LINK-FAIL occurs to the opposing node associated with the target node.





08Following message (Fig. 107) appears. But cutover operations are not still completed, Wait till the Cutover operations are completed. (about 20 minutes; On the New Event window, Association Fail alarm is cleared.)


Fig. 107 Completion of Cutover Operations


09Click Switch button.A dialog box for switch mode selection appears. (Fig. 109)


10From the Switch Mode options, select MemswitchOnly, and click OK button.Confirmation message (Fig.110) appears.














# End of Cutover and Swap Operations (Main: Rel. 2.30) procedure.6.18 Verify Cutover and Swap Operations (Main: Rel. 2.30 SC/FC)

When the Cutover and Swap operations are completed, the Main shelf of the target node now runs using the new firmware. Perform this procedure to confirm that the node is running the new firmware.



Then, right-click on the node to show the menu, and select Detail Setup. (Fig. 113)CID+ window (Fig. 114) appears.


02Open Inventory dialog box:

Click Reports -> Inventory (Fig. 114)Inventory dialog box (Fig. 115) appears.





04Check if indications for Active and Primary columns match to those listed in the version table below.Dialog box above is an example. Packages displayed in the Inventory dialog box differ depending on packages actually installed.



MSCM02.70(MSCM)02.7002.17

02.51(AGENT)02.5102.00

SSCM02.35(SW)02.3502.12

02.32(OHC)02.3202.07

MX320LE02.3702.3702.17

S64P02.0502.0501.32

S16P02.0502.0501.32

# Refer to Table 1 on Page 3.

>

# Contact NEC.

05When completed, close the Inventory dialog box and CID+ window.

# End of Verify Cutover and Swap Operations (Main: Rel. 2.30) procedure.7. Verify ConditionsConfirm that the applied procedures have not caused any problems, and the network conditions are the same as those before staring the procedures.


01Open the New Event dialog box of INC-100MS (Fig. 116), and check the current alarms and events:* When EXT16/EXTWB Shelf is/are added, ensure to release the MX320 from lockout referring to Appendix: Procedures to Add Extension Shelves provided in the back of this document. 1) Verify the record obtained by Section 5.3 Record the Current Condition, and compare it with the conditions reported by the New Event opened here.

2) Confirm that no alarm is newly occurring. No changes should exist between two lists of before and after the procedures. (after the procedures, SFT_VER alarms in EXT16 or EXTWB shelf are cleared.) If any alarms had already been reported at Section 5.3, those should remain in the list.

Fig. 116: New Event Dialog Box

# End of Verify Conditions and all of upgrading Release 2.10 to Release 2.30 procedures.

Appendix: Procedures to Add Extension Shelves1. Set LockoutBefore adding an extension shelf, MX320 should be locked out in order to prevent carrying out the protection switching while in the procedure.Complete all the physical connections to the UN5000 by referring to the SpectralWave( UN5000 User's Manual.StepWork DescriptionItems to VerifyCheck




02Click Maintenance -> Protection Switching -> Package/Line(Fig. 2).Protection Switching - Package/Line dialog box appears. (Fig. 3)

Fig. 2: CID+ Window


03Click XSWS tab to show the list, and select the MX320 switch group, then click the OK button. (Fig. 3)Protection Switching - XSWS dialog box appears. (Fig. 4)

Fig. 3: Protection Switching - Package/Line

04Open Protection Switching - XSWS dialog box (Fig. 4).

Click the Lockout check box to leave a tick, then click the Apply button.Message dialog box appears. (Fig. 5)

Fig. 4: Protection Switching - XSWS


05Click the Yes button of the message dialog box to proceed. (Fig. 5)Protection Switching Operation indicator (Fig. 6) appears while in progrees.* MNT LED on MSCM faceplate lights up in oragne.

Fig. 5: Massege

Fig. 6: Protection Switching Operation

06Upon the completion of the process, the indicator disappears. Check the Protection Status, and close the Protection Switching - XSWS dialog box, Protection Switching - Package/Line, and CID+ window.Verify that Package Protection indicates No Request .


# End of "Lockout procedure".2. Register Extension ShelfRefer to the INC-100MS Network Management System Provisioning (DOI-N08679) for methods of registering an xtension shelf and its accommodating packages.*For an OHCEXT Package of EXT16 Shelf, the registration should be done by CID. Refer to the SpectralWave( UN5000 Provisioning (DOI-07487) manual for its registering method.*Upgrading procedure cannot be carried out before registrations of the shelf and its accommodating packages are completed. However, at this point, the setups of sections and paths are not necessary.StepWork DescriptionItems to VerifyCheck

01Register all associated EXTWB Shelves.Refer to the INC-100MS Network Management System Provisioning manual (DOI-N08679).

02Register packages installed in EXTWB ShelvesRefer to the INC-100MS Network Management System Provisioning manual (DOI-N08679).

03Register all associated EXT16 Shelves.Refer to the INC-100MS Network Management System Provisioning manual (DOI-N08679).

04Register packages installed in EXT16 Shelves, except for OHCEXT Package,.Refer to the INC-100MS Network Management System Provisioning manual (DOI-N08679).

05Register OHCEXT Packages of EXT16 Shelves.Refer to the SpectralWave( UN5000 Users Manual, Provisioning manual (DOI-07487).

Proceed to beginning of this SpectralWave UN5000 Procedures to Upgrade Firmware.Ensure to release the Lockout state (Appendix: Procedures to Add Extension Shelves: 3. Release Lockout) when the upgrading procedures are completed.

3. Release LockoutUpon completion of adding extension shelves and registering all the packages, release the MX320 from the Lockout state.StepWork DescriptionItems to VerifyCheck




02Click Maintenance -> Protection Switching -> Package/Line(Fig. 9).Protection Switching - Package/Line dialog box appears. (Fig. 10)

Fig. 9: CID+ Window


03Click the XSWS tab to show the list, and select the target switch group, then click the OK button. (Fig. 10)Protection Switching - XSWS dialog box appears. (Fig. 11)

Fig. 10: Protection Switching - Package/Line

04Open Protection Switching - XSWS dialog box (Fig. 11).

Click the Lockout check box to remove a tick, then click the Apply button.Message dialog box appears. (Fig. 12)



05Click the Yes button of the message box. (Fig. 12)Protection Switching Operation indicator appears. (Fig. 13)*MNT LED on the MSCM faceplate goes off.

Fig. 12: Massege

Fig. 13: Protection Switching Operation

06When the Protection Switching Operation indicator disappears, check the indicated status in the dialog box, then close the Protection Switching - XSWS dialog box, Protection Switching - Package/Line dialog box, and CID+ window.Verify that Package Protection indicates No Request.


# End of "Release Lockout" procedure.

UN5000

UN5000A

main

UN5000

main

UN5000A

A0808024.SUN

A0230011.UN2

A0230011.UN2

A0230011.UN2

UN5000

main

UN5000A

A0808024.SUN

A0230011.UN2

A0230011.UN2

A0230011.UN2

A0230011.UN2

UN5000A

A0230011.UN2

* See AMP64 Setup Procedures

(provided in SpectralWave UN5000 AMP64 Setup Procedures (required before Firemware upgrade))

A0230014.UN2

A0230014.UN2

A0230015.UN2

A0230016.UN2

UN5000A

A0230014.UN2

A0230014.UN2

A0230014.UN2

A0808024.SUN

UN5000A

main

UN5000

A0230014.UN2

A0230014.UN2

A0808024.SUN

Final Check

AMP64 setup procedures *

[Working time: 10min/1 time]

7 Verify Conditions

Completed for all in the node?

[Operating Time: 5min/1 Eqpt.]

6.4, 6.8, 6.12, 6.16 Verify downloaded files

6.2 Verify F/W version

Verify F/W versions

Record the current condition

Date: [ ]

Site: [ ]

Name: [ ]

Date: [ ]

Site: [ ]

Name: [ ]

Yes

No

Verify Results of Cutover-Swap

6.3->6.4->6.5->6.6 (for EXTWB [Rel. 2.30])

6.7->6.8->6.9->6.10 (for EXT16 [Rel. 2.30])

6.11->6.12->6.13->6.14

(for Main [Rel. 2.30] AGENT)

6.15->6.16->6.17->6.18

(for Main [Rel. 2.30] SC/FC)

Cutover and Swap

6.5, 6.9, 6.13, 6.17 Cutover and Swap

6.6, 6.10, 6.14, 6.18 Verify Results of Cutover and Swap Operations

6.3, 6.7, 6.11, 6.15 Download bundle files



Verify downloaded files


Download bundle files


6.1 Install bundle files into INC-100MS Server


5.3 Record the current condition

[Operating Time: 10min/1 operation]

Install bundle files

A0230011.UN2

5.2 Verify Network Parameter Condition

[Operating Time: 10min/1 operation]

Verify

Network Parameter Condition

* Packages listed in the yellow-colored rows are the targets of this upgrading.

* Packages listed in the blue-colored rows are to be replaced with a new package (New Version) prepared in advance.

* Packages listed in the pink-colored rows may cause the traffic interruption if the upgrading procedure is carried out while in service. (Refer to chapter 5. Need-to-Know Things)

Table 1: Applicable F/W Versions for Equipment Releases

Page. 1/85 HEC-40-0111-02

2_un5000 upgrade procedure for r230(indsat)_3

Documents

swap main

unode version10

unode version11

unode version ext16

swap operations main

gbprunode version51

swap ext16

downloaded files main