2x2 nec display video wall installation guide

7/31/2019 2x2 NEC Display Video Wall Installation Guide

1/14

7/31/2019 2x2 NEC Display Video Wall Installation Guide

2/14

2x2 Video Wall - NECUN Series Displays -

Installation Guide

Step 1 - Preparation

1. Verify that installation location is ready (power, network, wallreinforced, adequate ventilation, coax cable if being installed)

2. Open all packages and lay everything out. Make sure all

materials are present and there is no visible damage.

Installation Tip: If the installation location is not ready orany materials are missing or damaged, call the Rise DisplayProject Manager for instructions.

Revised 05-31-2012 Page 2

7/31/2019 2x2 NEC Display Video Wall Installation Guide

3/14

Step 2 - Install OPS Media Player

1. Select one of the LCD Displays and install the OPS Media

Player perOPS Media Player Installation guide.2. After installing the OPS Media Player, set display aside.

This display will be Display #1.3. Insert the keyboard and mouse USB dongle into a USB port

on the OPS Media Player.

Step 3 - Install 2x2 Video Wall Mount and LCD Displays

1. Install 2x2 video wall mount and LCD Displays per2x2 WallMount Installation guide. **Mounting configuration is thesame for X551UN, X461UN, X462UN and X463UN**

Installation Tip: Leave adequate space between the leftand right sides to access the rear of video wall and slide thedisplays together after cabling is completed.

Installation Tip: The Ultra-Thin bezels on the UN displaysare very easily damaged - take extreme caution duringinstallation to avoid damage. Use cardboard betweendisplays as you install and remove cardboard whendisplays are safely in place.

Revised 05-31-2012 Page 3

7/31/2019 2x2 NEC Display Video Wall Installation Guide

4/14

Step 4 - Connect all Cables

Step 4A - RS232 Cables

1. Install RS232 Null Modem cables. Refer to RS232 WiringDiagram at right.

Installation Tip: RS232 ports are labeled IN and OUT ondisplay - double check to ensure you have cable connectedto correct port - The RS232 OUTPUT ports are the ports

closest to the wall when display is installed.

Front of Display

Revised 05-31-2012 Page 4

7/31/2019 2x2 NEC Display Video Wall Installation Guide

5/14

Step 4B - Display Port Cables

1. Install Display Port cabling. Refer to Display Port (DP)Wiring Diagram at right.

Installation Tip: Display Port (DP) ports are labeled INand OUT on display - double check to ensure you have

cable connected to correct port - As you are facing the frontof the screen, the Display Port IN is on the left.

Front of Display

Revised 05-31-2012 Page 5

7/31/2019 2x2 NEC Display Video Wall Installation Guide

6/14

Step 4C - Infrared Remote and Ambient Light Sensor cable

1. Install Infrared Remote and Ambient Light Sensor cable at

this time. You will not install the sensor until later.2. Connect one end of the mini cable to the Remote IN mini

jack on display #1.3. Leave the other end of the cable out and hanging where

you will be able to get to it later when you install the sensor.4. You will not be using the Remote OUT port

Installation Tip: Remote ports are labeled IN and OUT ondisplay - double check to ensure you have cable connectedto correct port - The Remote IN port is the port farthest fromthe wall when display is installed.

Front of Display

Revised 05-31-2012 Page 6

7/31/2019 2x2 NEC Display Video Wall Installation Guide

7/14

Step 4D - Power and Network

1. Connect one end of Ethernet patch cable to customer

provided Ethernet jack - you will connect this to theEthernet connection on the OPS Media Player in display 1.

2. Connect 6 outlet surge suppressor to customer providedAC outlet. You will connect all power cords from thedisplays and the external TV tuner (if used) to this surgesuppressor.

Revised 05-31-2012 Page 7

7/31/2019 2x2 NEC Display Video Wall Installation Guide

8/14

Step 5A - Power up and configuration

1. Make sure the main power switch on each display is ON

(The main power switch is located on the back of thedisplay where the power cord connects)

2. Power on the 2x2 display by turning power on to eachdisplay individually.

3. Powering on display 1 will automatically power on the OPSMedia Player.

Installation Tip: Make sure all 4 displays have the input setto Display Port using the remote control. If input is not setto Display Port, monitors will go into power save mode.

Important- you should now see the same image on all 4displays

Revised 05-31-2012 Page 8

7/31/2019 2x2 NEC Display Video Wall Installation Guide

9/14

Step 5B - Set up Tile Matrix

1. Set up Tile Matrix on 2x2 video wall. This is done using the

on screen menus on the NEC displays.2. Refer to Tile Matrix configuration document for details.

Revised 05-31-2012 Page 9

7/31/2019 2x2 NEC Display Video Wall Installation Guide

10/14

Step 5C - Set up Individual Display ID

Using the remote control, set each of the 4 displays with theirunique display ID and Primary/Secondary status as follows:

1. Select Menu button to get on-screen menu to display

2. Scroll over to select MULTI-DISPLAY function

3. Scroll to highlight MONITOR ID function

4. Scroll to select MONITOR ID

5. For Display #1, select ID No. 1, for Display #2, select ID No.

2, for Display #3, select ID No. 3 and for Display #4, select

ID No. 4 so that each display has its own unique ID No.6. Each of the Displays will remain in Group A

7. Now scroll down to IR CONTROL

8. For Display #1 ONLY - set IR CONTROL to PRIMARY

9. For all other displays - set IR CONTROL to SECONDARY

Installation Tip: To control displays after setting this up, push

the DISPLAY button on the remote then push the number on thekeypad for the display you wish to control. So to control display3, push DISPLAY, then the number 3. Now you will be controllingdisplay #3

Set Monitor ID

Set Primary/Secondary Status

Revised 05-31-2012 Page 10

7/31/2019 2x2 NEC Display Video Wall Installation Guide

11/14

Step 6 - Install TV Tuner

If no TV is to be installed, skip this step

Connect Hauppauge USB TV tuner connections.

1. Coax cable from client network to coax connector on tunerlabeled TV.

2. USB connection from TV tuner to open USB slot on OPSMedia Player.

3. Power - Plug AC adapter into power strip and connect tothe Power In (+6V) on tuner. There is no power switch on

the tuner, it will power on when plugged in - check red LEDpower indicator to make sure tuner is on.

4. Locate TV tuner behind display out of sight just abovethe OPS Media Player. Once you have placed the tunerbehind the screen and verified that it is out of sight, removeit briefly and place a bit of the supplied velcro on the back ofthe tuner and on the wall where it will go. Then tuck the TVtuner behind the display out of sight, secure with velcro andtie all cables neatly out of view.

5. All drivers and WinTV come installed and preconfigured onthe OPS Media player and no configuration is needed.

If needed - consult the external USB TV Tuner guideHauppauge external USB TV tuner installation guide

Revised 05-31-2012 Page 11

7/31/2019 2x2 NEC Display Video Wall Installation Guide

12/14

Step 7 - Install Over-frame Bezel Kit

1. Install over-frame Bezel Kit perBezel Kit installation

instructions for 2x2 video wall (page 2 of document -installation guide is also included in bezel kit box)

2. Use only the screws provided in the kit as any other screwsmay damage LCD displays.

Note: You were provided with 2 over-frame kits and it will requireboth to frame the 2x2 video wall.

Revised 05-31-2012 Page 12

7/31/2019 2x2 NEC Display Video Wall Installation Guide

13/14

Step 8 - Install Infrared Remote and Ambient Light Sensor

1. Install Infrared Remote and Ambient Light Sensor per

Infrared Remote and Ambient Light Sensor installationguide. Installation guide is also included in sensor box.

2. Using any of the over-frame bezel attachment screws,attach the sensor in the best location for the client location -however, do not attach the sensor at the top center of eitherLCD display

3. After you have attached the sensor, connect the free endof the 3.5mm mini cable that you plugged into Remote IN instep 4D

Revised 05-31-2012 Page 13

7/31/2019 2x2 NEC Display Video Wall Installation Guide

14/14

Step 9 - Display Configuration

1. Reboot display by restarting Windows.2. Set up Power Schedule for displays if client wishes - using

on screen menus. (see page 27 of the NEC users manual)3. Disable buttons on NEC Displays. To activate the control

key lock function, press both and (on the display, notthe remote) and hold down simultaneously for more than3 seconds. To resume user mode, press both and holdsimultaneously for more than 3 seconds.

4. Put Velcro on remote and attach to the back of the left side(as you are facing the front of the video wall) of display #3

Step 10 - Wrap Up

1. Remove all trash and extra parts - dispose of properly2. Clean up work area - wipe down displays3. Provide 3 remote controls, keyboard and mouse to client.4. Obtain written sign off from customer5. Take pictures of installation and email to

[email protected] and copy the Rise Display ProjectManager.

6. Call the Rise Display Project Manager to review installation

Revised 05-31-2012 Page 14