3rd International Conference

CAR INTERIORSTechnological challengesas a competitive factor

30 – 31 May 2012Centro Congressi Torino Incontra

Room GiolittiVia Nino Costa 8 - Torino (Italy)

ATA-Associazione Tecnica dell’Automobile (the Italian Automotive Society) and Centro Ricerche Fiat are delighted to announce the forthcoming 3rd International Conference on “Car Interiors: technological challenges as a competitive factor”, that will take place in Torino, on 30 - 31 May 2012. This conference addresses to all players in this field, including vehicle manufacturers, suppliers of components and systems, public entities, decision makers, engineers and scientists. It will provide an excellent platform for information exchange on an International level and will allow to assess the status and potential for Internal Vehicle Technologies and Materials.

The technical programme, in which the selected papers will be included, is divided into the following main topics:

• Seats• Cockpit & Trims• HMI - Human Machine Interaction• Perceived Quality• Ergonomics• Dynamic simulation about materials for interiors.

Chairman of the ConferenceSilvia Quattrocolo (Centro Ricerche Fiat)

This event is organised under FISITA Patronage

FISITA is the international federation linking the national automotive engineering societies in 37 countries. FISITA was founded in 1948 as a neutral forum for the exchange of technical

knowledge on every aspect of vehicle design, development and manufacture. FISITA is a non-profit organisation committed to helping create efficient, affordable, safe and sustainable

automotive transportation. www.fisita.com

With the support of

30 May 2012

From 8.15 Participants’ registration

9:00 Welcome addresses: G. Bolatto (Segretario Generale della Camera di commercio di Torino) N. Di Giusto (Presidente ATA)

9:30 Key-note by V. Fernandez (Fiat Group Automobiles)

10:00 Session 1 ‘Innovative Scenarios’ chaired by C. Germak–Politecnico di Torino

• C. Germak – Politecnico di Torino Sustainable mobility roadmap. The Politecnico’s approach to the automotive design issues

• S. Jakubiec - Fiat Group Automobiles 10:45 – 11:15 Coffee break

• F. Cappadona – Pininfarina Advanced navigation system for urban ecofriendly vehicles

• M. Carignano – Iveco What is the interior system for a C.V.? Beauty and comfort?

• A. Boldrin – Decathlon Italia Decathlon: innovate through the passion brands

Discussion coordinated by the Chairman

12:45 – 14:00 Lunch

14:00 Session 2 ‘Seating’

• H. J. Daams – Ziegler Instruments Analysing the formation of pleats in seats for leather and fabrics using REBEX

• M. Raveggi – Johnson Controls

• R. Dwarampudi, C. Cabane, C. Marca – ESI Group Example of End-to-End Seat Virtual Prototyping from manufacturing to performances

• G. Creonti – Structura Mass and cheap productivity of Composite light components for automotive

• T. Mannelli – Apollo Fabrics from recycled materials

• M. J. Mazza - Woodbridge Group The Comfort Sense, textured surface seat cushioning for improving initial softness and upgrading active and passive ventilated seats

Discussion coordinated by the Chairman

16:15 – 16:35 Coffee break

16:35 Session 3 ‘Cockpit and Trims’

• F. Avenati-Bassi – Autoneum Italy; E. Negro, C. Campagna, A. Marino, G. Boreanaz – Fiat Group Automobiles; C. Bertolini, M. Mantovani - Autoneum Management Hybrid Acoustic Insulator-absorber modelling. The best compromise between performances and weight: a dash-inner real example

• A. Odino, F. Carello – Renolit Gor RENOLIT GORCELL – Innovative Honeycomb solution

• L. Bergadano – UNIFAST UNIFAST: the fasteners supplier and solutions provider of the automotive industry

• F. Rey – Grupo Antolin Italia Innovation as a key factor for competitiveness at Grupo Antolin

Discussion coordinated by the Chairman

31 May 2012

9:00 Key-note ‘Human Centred Design: creating added value for automotive interiors’ J. Giacomin - Brunel University

9:30 Session 4 ‘HMI-Human Machine Interaction and Ergonomics’

• M. Barbera – Reply Bringing diagnostic to smartphone interface

• H. Prashanth - Robert Bosch Journey from Function HMI to Vehicle HMI

• F. MacDougall - Qualcomm Inc. Touch Free In-Car Gesture Control

10:30 – 10:50 Coffee Break

• P. De La Pierre -  Magneti Marelli; C. Argiri - TXT e-solutions Instrument Cluster 2.0

• C. P. Giordano - The DiSTI Corporation, C. Schröder - Antycip Simulation Advancements in Technology Facilitating Next Generation 3D Interactive HMI

• C. Zoldan – Centro Ricerche Fiat HMI in the automotive field

• M. Fischer – ENGEL Austria "Sensitive surface: touch, feel, interact" a car cockpit without buttons

Discussion coordinated by the Chairman

12:30 – 14:00 Lunch

14:00 Session 5 ‘Perceived quality’

• B. Nicosia, M. Varrasso – IVECO; E. Bergadano, F. Fino – Fiat Group Automobiles Innovative opportunity for Perceived Quality improvement: 2K direct skinning for soft interior trims

• A. Wilson – ESI Group Predicting the acoustics of rattle across a broad frequency range

• H. J. Daams – Ziegler Instruments Objective measurement of touch haptics – a subgroup of Perceived Quality

• L. Mondino – Adler Evo Surface materials with antibacteria treatment

• V. Bortolon - SOFTER  Technology Dolphin for a sustainable eco-friendly full thermoplast solution for soft touch interiors (using MuCell phisical foaming process). 

Discussion coordinated by the Chairman & conference closure

 

.

Contact: Marisa Giunipero ATA – Associazione Tecnica dell’AutomobileStrada Torino 32/A – 10043 Orbassano (TO) - ItalyPhone: +39.011.9080405 Fax: +39.011.9080400marisa.giunipero@crf.it VenueThe Conference will take place at: Centro Congressi TORINO INCONTRA - Room GIOLITTI Via Nino Costa 8 – Torino (Italy) http://www.torinoincontra.org/It is in the centre of Torino, at a 10-minutes-walking from Porta Nuova Railway Station. Shuttle bus (SADEM Company) from Caselle Airport to Porta Nuova, stops on the corner of Via Sacchi and Corso Vittorio Emanuele II. Timetable on http://www.sadem.it/upload/orari/estivi/000268.pdf

If you reach the venue by carThe Conference venue is located in the ZTL (the Restricted Traffic Area), so we remind participants who will park their car in the PARKING AREA VALDO FUSI between 7:30-10:30 in the morning, to communicate their car plate number to the parking staff, at their arrival and in any case before 11:00 in the morning, in order to avoid a fine.  Language & presentationsPapers will be written and presented in English. It will be possible to download all presentations from the ATA website. The access will be limited to the participants, by using a password that will be provided by email a few days after the Conference.

Registration & cancellation policyYou can register either on-line or via fax/email.Refunds will be given to cancellations received in writing prior to 15 May 2012. No refunds will be given after this deadline. Replacement delegates are welcome at any time.

PaymentWe accept payments:• on-line• by bank transfer• by credit card at the reception desk.

Congress DinnerThe Congress Dinner will take place on 30 May.

Hotel information Accommodation is not included in the Conference registration fee. Since this event takes place in the town centre, you can choose from a wide selection of hotels.

If you decide for a 20 mt distance from the main entrance of the Conference, we suggest:Hotel Victoria – Via Nino Costa 4 – 10123 Torino - phone +39 011 5611909 To get discounted fares, please refer to this event to be held at Torino Incontra Congress Centre.Single Standard room: € 140 – DUS Standard room: € 160 – Double standard room: € 225

If you decide for a walking distance (10 minutes) from the Conference, we suggest: Best Western Hotel Piemontese - Via Berthollet 21 - 10125 Torino – Phone +39 011 66 98 101 www.hotelpiemontese.it

III International Conference ‘CAR INTERIORS’ – 30-31 May 2012  Please complete and return this form to: Fax: +39.011.9080400 or e-mail: marisa.giunipero@crf.it Surname…………………………………………………………….……………………Name……………………………………………………………

Title and position………………………………………………………………………………………………………………………………………….

Company……………………………….…………………..……………………………….Dept……………………………………….……………….

Address……………………………………………………….…………………………………………………………………………………………………

Post Code………………….……………City…………………………….…………………..….…….……Country……………………………….

Phone…………………………….………….……………………………..Mobile…………………………..…………………………………………….

E-mail ……………………………………………..…………………………………………………………………………………………………………….

Registration fees (On-line proceedings, coffee, lunches, congress dinner and 21% VAT are included)

Speaker € 363,00 ATA member € 544,50 Delegate (non member) € 665,50

I will attend the congress dinner Yes No

Payment Bank transfer to A.T.A. - S.r.L. - Banca Popolare di Novara, Filiale Beinasco TO (Italy) IBAN: IT42L0503430090000000020407 BIC: BAPP IT 21A93 (payment must be received before start of Conference)

Credit card / POS Bancomat at the congress reception desk. Full refunds will be given to cancellations received in writing prior to 15 May 2012. No refunds will be given after this deadline.

Invoice to Company ………………………………………………………………………………………………………………

Department ……………………………………………………………………………………………………………………………….

Address ……………………………………………………………………………………………………………………………………...

CAP....…………..........City..................……………………………......Country …………………………………….

P. IVA / VAT Number ………………………………………………………………………………………………………………..

Codice Fiscale (only for Italian Companies)………………………………………………………………………………

Account Dept e-mail……………………………………………………………………………………………………………………  I authorise ATA to make an audio-video recording of this event.In compliance with art. 7 of Italian law 196/2003, your personal data are used exclusively for processing ATA activities. For further information about our privacy policy: http://www.ata.it/en/content/42/privacy/

Date……………………...………......................Signature......................................................................

ATA Consulting & Solutions srl - Strada Torino 32 A – 10043 Orbassano (TO) – ItalyPartita IVA / Codice Fiscale 10241220010