3.2 characteristics: - latest seminar topics for · web viewtitle automatic room light...

72
TITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER

Upload: dangdieu

Post on 23-Mar-2018

226 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

TITLE

AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER

Page 2: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

ABSTRACT

This Project “Automatic Room Light Controller with Visitor Counter using Microcontroller” is a reliable circuit that takes over the task of controlling the room lights as well us counting number of persons/ visitors in the room very accurately. When somebody enters into the room then the counter is incremented by one and the light in the room will be switched ON and when any one leaves the room then the counter is decremented by one. The light will be only switched OFF until all the persons in the room go out.

The total number of persons inside the room is also displayed on the seven segment displays. The microcontroller does the above job. It receives the signals from the sensors, and this signal is operated under the control of software which is stored in ROM. Microcontroller AT89S52 continuously monitor the Infrared Receivers, When any object pass through the IR Receiver's then the IR Rays falling on the receivers are obstructed this obstruction is sensed by the Microcontroller.

Page 3: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

CONTENTS

CHAPTER 1: INTRODUCTION

1.1 Aim of the project

1.2 Project Overview 1.3 Methodology

CHAPTER 2: BLOCK DIAGRAM AND ITS DESCRIPTION 2.1 Basic block diagram

2.2 Block diagram description

CHAPTER 3: EMBEDDED SYSTEMS 3.1 Introduction to Embedded Systems:

3.2 Characteristics:

3.3 Platform:

3.4 Tools:

3.5 Operating system:

3.6 Debugging:

3.7 Design of embedded systems:

3.8 Start-up:

3.9 The control loop

3.10 User interface

Page 4: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

CHAPTER4: POWER SUPPLY 4.1 POWER SUPPLY UNIT 4.2 REGULATOR LM7805 4.3 DESCRIPTION 4.4 CIRCUIT FEATURES

4.5 BLOCK DIAGRAM 4.5.1Transformer 4.5.2Rectifier 4.5.3Filter

4.5.4Voltage regulator

CHAPTER5: 89S52 MICROCONTROLLER

5.1 Features

5.2 Description 5.3 Pin Diagram - AT89S52 5.4 Pin description 5.5 ARCHITECHTURE OF 8052 MICROCONTROLLER:

5.5.1 Oscillator Characteristics

5.5.2 Idle Mode

5.6 Oscillator Connections

CHAPTER6: IR SENSORS

6.1 IR Remote Control Theory 6.2 Infra-Red Light

Page 5: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

6.3 Modulation 6.4 The Transmitter

6.5 The receiver

CHAPTER7: RELAY CIRCUIT

CHAPTER8: SOURCE CODE

CHAPTER9: FUTURE EXPANSION

CHAPTER10: APPLICATIONS, ADVANTAGES AND DISADVANTAGES

CHAPTER11: REFERENCES

Page 6: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

CHAPTER 1INTRODUCTION

Page 7: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

1.1 Aim of the project: The main objective of this project is to make a controller based model to count number of persons visiting particular room and accordingly light up the room using IR sensors.

1.2 Project Overview :This Project Automatic Room Light Controller with Visitor Counter using

Microcontroller is a reliable circuit that takes over the task of controlling the

room lights as well us counting number of persons/ visitors in the room very

accurately. When somebody enters into the room then the counter is incremented

by one and the light in the room will be switched ON and when any one leaves

the room then the counter is decremented by one. The light will be only switched

OFF until all the persons in the room go out. The total number of persons inside

the room is also displayed on the LCD.

The microcontroller does the above job. It receives the signals from the sensors,

and this signal is operated under the control of software which is stored in ROM.

Microcontroller AT89S52 continuously monitor the Infrared Receivers, When

any object pass through the IR Receiver's then the IR Rays falling on the receiver

are obstructed, this obstruction is sensed by the Microcontroller.

1.3 Methodology:

According to our project requirements, the following modules are

essential.

Power supply

Microcontroller

IR sensors

Relay

Page 8: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

CHAPTER 2 BLOCK DIAGRAM AND ITS DESCRIPTION

Page 9: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

2.1 Basic Block Diagram:

Fig. 2.1 Block diagram

Page 10: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

2.2 Block Diagram Description:

The basic block diagram of the Automatic Room Light Controller with Visitor

Counter is shown in the above figure. Mainly this block diagram consists

of the following essential blocks.

1. Power Supply

2. AT89S52 micro-controller

3. Entry and Exit sensor circuit

4. Relay driver circuit

1. Power Supply: Here we used +12V and +5V dc power supply. The main

function of this block is to provide the required amount of voltage to

essential circuits. +12 voltage is given. +12V is given to relay driver. To

get the +5V dc power supply we have used here IC 7805, which provides

the +5V dc regulated power supply.

2. 89S52 Microcontroller: It is a low-power, high performance CMOS 8-bit

microcontroller with 8KB of Flash Programmable and Erasable Read Only

Memory (PEROM). The device is manufactured using Atmel’s high-

density nonvolatile memory technology and is compatible with the MCS-

51TM instruction set and pin out. The on-chip Flash allows the program memory

to be reprogrammed in-system or by a conventional nonvolatile memory

programmer. By combining a versatile 8-bit CPU with Flash on a

monolithic hip, the Atmel AT89S52 is a powerful microcontroller, which

provides a highly flexible and cost effective solution to so many embedded

control applications.

Page 11: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

3. Enter and Exit Circuits: This is one of the main part of our project. The main intention of this

block is to sense the person. By using this sensor and its related circuit diagram we can

count the persons.

4. Relay Driver Circuit: This block has the potential to drive the various controlled

devices. In this block mainly we are using the transistor and the relays.

One relay driver circuit we are using to control the light. Output signal

from AT89S52 is given to the base of the transistor, which we are further

energizing the particular relay. Because of this appropriate device is

selected and it do its allotted function.

Page 12: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

CHAPTER 3EMBEDDED SYSTEMS

Page 13: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

3.1 Introduction to Embedded Systems: Embedded systems are electronic devices that incorporate microprocessors with in their implementations. The main purposes of the microprocessors are to simplify the system design and provide flexibility. Having a microprocessor in the device means that removing the bugs, making modifications, or adding new features are only matters of rewriting the software that controls the device. Or in other words embedded computer systems are electronic systems that include a microcomputer to perform a specific dedicated application. The computer is hidden inside these products. Embedded systems are ubiquitous. Every week millions of tiny computer chips come pouring out of factories finding their way into our everyday products.

Embedded systems are self-contained programs that are embedded within a piece of hardware. Whereas a regular computer has many different applications and software that can be applied to various tasks, embedded systems are usually set to a specific task that cannot be altered without physically manipulating the circuitry. Another way to think of an embedded system is as a computer system that is created with optimal efficiency, thereby allowing it to complete specific functions as quickly as possible.

Embedded systems designers usually have a significant grasp of hardware technologies. They used specific programming languages and software to develop embedded systems and manipulate the equipment. When searching online, companies offer embedded systems development kits and other embedded systems tools for use by engineers and businesses.

Embedded systems technologies are usually fairly expensive due to the necessary development time and built in efficiencies, but they are also highly valued in specific industries. Smaller businesses may wish to hire a consultant to determine what sort of embedded systems will add value to your organization.

3.2 Characteristics:

Two major areas of differences are cost and power consumption. Since many embedded systems are produced in the tens of thousands to millions of units range, reducing cost is a major concern. Embedded systems often use a (relatively) slow processor and small memory size to minimize costs.

Page 14: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

The slowness is not just clock speed. The whole architecture of the computer is often intentionally simplified to lower costs. For example, embedded systems often use peripherals controlled by synchronous serial interfaces, which are ten to hundreds of times slower than comparable peripherals used in PCs.

Programs on an embedded system often must run with real-time constraints with limited hardware resources: often there is no disk drive, operating system, keyboard or screen.

A flash drive may replace rotating media, and a small keypad and LCD screen may be used instead of a PC's keyboard and screen.

Firmware is the name for software that is embedded in hardware devices, e.g. in one or more ROM/Flash memory IC chips.

Embedded systems are routinely expected to maintain 100% reliability while running continuously for long periods, sometimes measured in years. Firmware is usually developed and tested too much stricter requirements than is general-purpose software, which can usually be easily restarted if a problem occurs.

3.3 Platform:

There are many different CPU architectures used in embedded designs. This in contrast to the desktop computer market, which as of this writing (2003) is limited to just a few competing architectures, mainly the Intel/AMD x86, and the Apple/Motorola/IBM PowerPC, used in the Apple Macintosh.

One common configuration for embedded systems is the system on chip, an application-specific integrated circuit, for which the CPU was purchased as intellectual property to add to the IC's design.

3.4 Tools:

Like a typical computer programmer, embedded system designers use compilers, assemblers and debuggers to develop an embedded system.

Those software tools can come from several sources:

Page 15: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

Software companies that specialize in the embedded market Ported from the GNU software development tools.

Sometimes, development tools for a personal computer can be used if the embedded processor is a close relative to a common PC processor.

Embedded system designers also use a few software tools rarely used by typical computer programmers.

Some designers keep a utility program to turn data files into code, so that they can include any kind of data in a program.

Most designers also have utility programs to add a checksum or CRC to a program, so it can check its program data before executing it.

3.5 Operating system:

They often have no operating system, or a specialized embedded operating system (often a real-time operating system), or the programmer is assigned to port one of these to the new system.

3.6 Debugging:

Debugging is usually performed with an in-circuit emulator, or some type of debugger that can interrupt the micro controller’s internal microcode.

The microcode interrupt lets the debugger operate in hardware in which only the CPU works. The CPU-based debugger can be used to test and debug the electronics of the computer from the viewpoint of the CPU. This feature was pioneered on the PDP-11.

Developers should insist on debugging which shows the high-level language, with breakpoints and single stepping, because these features are widely available. Also, developers should write and use simple logging facilities to debug sequences of real-time events.

PC or mainframe programmers first encountering this sort of programming often become confused about design priorities and acceptable methods. Mentoring, code-reviews and ego less programming are recommended.

Page 16: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

3.7 Design of embedded systems: The electronics usually uses either a microprocessor or a micro controller. Some large or old systems use general-purpose mainframes computers or minicomputers.

3.8 Start-up: All embedded systems have start-up code. Usually it disables interrupts, sets up the electronics, tests the computer (RAM, CPU and software), and then starts the application code. Many embedded systems recover from short-term power failures by restarting (without recent self-tests). Restart times under a tenth of a second are common.

Many designers have found one of more hardware plus software-controlled LEDs useful to indicate errors during development (and in some instances, after product release, to produce troubleshooting diagnostics). A common scheme is to have the electronics turn off the LED(s) at reset, whereupon the software turns it on at the first opportunity, to prove that the hardware and start-up software have performed their job so far. After that, the software blinks the LED(s) or sets up light patterns during normal operation, to indicate program execution progress and/or errors. This serves to reassure most technicians/engineers and some users.

3.9 The control loop: In this design, the software simply has a loop. The loop calls subroutines. Each subroutine manages a part of the hardware or software. Interrupts generally set flags, or update counters that are read by the rest of the software.

A simple API disables and enables interrupts. Done right, it handles nested calls in nested subroutines, and restores the preceding interrupt state in the outermost enable. This is one of the simplest methods of creating an exokernel. Typically, there's some sort of subroutine in the loop to manage a list of software timers, using a periodic real time interrupt. When a timer expires, an associated subroutine is run, or flag is set. Any expected hardware event should be backed-up with a software timer. Hardware events fail about once in a trillion times. That's about once a year with modern hardware. With a million mass-produced devices, leaving out a software timer is a business disaster.

Page 17: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

State machines may be implemented with a function-pointer per state-machine (in C++, C or assembly, anyway). A change of state stores a different function into the pointer. The function pointer is executed every time the loop runs.

Many designers recommend reading each IO device once per loop, and storing the result so the logic acts on consistent values. Many designers prefer to design their state machines to check only one or two things per state. Usually this is a hardware event, and a software timer. Designers recommend that hierarchical state machines should run the lower-level state machines before the higher, so the higher run with accurate information. Complex functions like internal combustion controls are often handled with multi-dimensional tables. Instead of complex calculations, the code looks up the values. The software can interpolate between entries, to keep the tables small and cheap.

One major weakness of this system is that it does not guarantee a time to respond to any particular hardware event. Careful coding can easily assure that nothing disables interrupts for long. Thus interrupt code can run at very precise timings. Another major weakness of this system is that it can become complex to add new features. Algorithms that take a long time to run must be carefully broken down so only a little piece gets done each time through the main loop.

This system's strength is its simplicity, and on small pieces of software the loop is usually so fast that nobody cares that it is not predictable. Another advantage is that this system guarantees that the software will run. There is no mysterious operating system to blame for bad behavior.

3.10 User interfaces:User interfaces for embedded systems vary wildly, and thus deserve some special comment. Designers recommend testing the user interface for usability at the earliest possible instant. A quick, dirty test is to ask an executive secretary to use cardboard models drawn with magic markers, and manipulated by an engineer. The videotaped result is likely to be both humorous and very educational. In the tapes, every time the engineer talk, the interface has failed: It would cause a service call.

Interface designers at PARC, Apple Computer, Boeing and HP minimize the number of types of user actions. For example, use two buttons (the absolute minimum) to control a menu system (just to be clear, one button should be "next menu entry" the other button should be "select this menu

Page 18: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

entry"). A touch-screen or screen-edge buttons also minimize the types of user actions.

Another basic trick is to minimize and simplify the type of output. Designs should consider using a status light for each interface plug, or failure condition, to tell what failed. A cheap variation is to have two light bars with a printed matrix of errors that they select- the user can glue on the labels for the language that she speaks. For example, Boeing's standard test interface is a button and some lights. When you press the button, all the lights turn on. When you release the button, the lights with failures stay on. The labels are in Basic English. For another example, look at a small computer printer. You might have one next to your computer. Notice that the lights are labeled with stick-on labels that can be printed in any language. Really look at it.

Designers use colors. Red means the users can get hurt- think of blood. Yellow means something might be wrong. Green means everything's OK. Another essential trick is to make any modes absolutely clear on the user's display. If an interface has modes, they must be reversible in an obvious way. Most designers prefer the display to respond to the user. The display should change immediately after a user action. If the machine is going to do anything, it should start within 7 seconds, or give progress reports.

If a design needs a screen, many designers use plain text. It can be sold as a temporary expedient. Why is it better than pictures? Users have been reading signs for years. A GUI is pretty and can do anything, but typically adds a year from artist, approval and translator delays and one or two programmers to a project's cost, without adding any value. Often, a clever GUI actually confuses users.

If a design needs to point to parts of the machine (as in copiers), these are labeled with numbers on the actual machine, that are visible with the doors closed. A network interface is just a remote screen. It needs the same caution as any other user interface.

One of the most successful general-purpose screen-based interfaces is the two menu buttons and a line of text in the user's native language. It's used in pagers, medium-priced printers, network switches, and other medium-priced situations that require complex behavior from users.

When there's text, there are languages. The default language should be the one most widely understood. Right now this is English. French and Spanish follow.

Page 19: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

Most designers recommend that one use the native character sets, no matter how painful. People with peculiar character sets feel coddled and loved when their language shows up on machinery they use.

Text should be translated by professional translators, even if native speakers are on staff. Marketing staff have to be able to tell foreign distributors that the translations are professional.A foreign organization should give the highest-volume distributor the duty to review and correct any translations in his native language. This stops critiques by other native speakers, who tend to believe that no foreign organization will ever know their language as well as they.

Page 20: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

CHAPTER 4 POWER SUPPLY

Page 21: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

4.1 POWER SUPPLY UNIT:

Fig. 4.1 Power supply unit

The power supply unit is used to provide constant 5 V dc supply to the peripherals. The 230 V ac is converted into 9 V ac by using a transformer and then a bridge rectifier rectifies it to a 9 V dc with ac ripples. This is then filtered by electrolytic capacitors used across the rectifier output. LM7805 regulator is employed to obtain a constant 5 V dc at the output.

4.2 REGULATOR LM7805:

Fig. 4.2 Regulator LM7805

Page 22: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

This is a digital IC used as a regulator for regulating the output. LM7805 provides a constant 5V dc supply as output. For this it needs at least 8V dc as input.

4.3 DESCRIPTION:

A variable regulated power supply, also called a variable bench power supply, is one where you can continuously adjust the output voltage to your requirements. Varying the output of the power supply is the recommended way to test a project after having double checked parts placement against circuit drawings and the parts placement guide.

This type of regulation is ideal for having a simple variable bench power supply. Actually this is quite important because one of the first projects a hobbyist should undertake is the construction of a variable regulated power supply. While a dedicated supply is quite handy e.g. 5V or 12V, it's much handier to have a variable supply on hand, especially for testing.

Most digital logic circuits and processors need a 5 volt power supply. To use these parts we need to build a regulated 5 volt source. Usually you start with an unregulated power supply ranging from 9 volts to 24 volts DC (A 12 volt power supply is included with the Beginner Kit and the Microcontroller Beginner Kit.). To make a 5 volt power supply, we use a LM7805 voltage regulator IC (Integrated Circuit). The IC is shown below.

The LM7805 is simple to use. You simply connect the positive lead of your unregulated DC power supply (anything from 9VDC to 24VDC) to the Input pin, connect the negative lead to the Common pin and then when you turn on the power, you get a 5 volt supply from the Output pin.

4.4 CIRCUIT FEATURES:

Brief description of operation: Gives out well regulated +5V output, output

current capability of 100 mA

Circuit protection: Built-in overheating protection shuts down output when

regulator IC gets too hot

Circuit complexity: Very simple and easy to build

Circuit performance: Very stable +5V output voltage, reliable operation

Page 23: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

Availability of components: Easy to get, uses only very common basic

components

Design testing: Based on datasheet example circuit, I have used this circuit

successfully as part of many electronics projects

Applications: Part of electronics devices, small laboratory power supply

Power supply voltage: Unregulated DC 8-18V power supply

Power supply current: Needed output current + 5 mA

Component costs: Few dollars for the electronics components + the input

transformer cost

4.5 BLOCK DIAGRAM:

Fig. 4.3 Block diagram of power supply

The input to the circuit is applied from the regulated power supply. The a.c. input

i.e., 230V from the mains supply is step down by the transformer to 12V and is

fed to a rectifier. The output obtained from the rectifier is a pulsating d.c voltage.

Page 24: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

So in order to get a pure d.c voltage, the output voltage from the rectifier is fed to

a filter to remove any a.c components present even after rectification. Now, this

voltage is given to a voltage regulator to obtain a pure constant dc voltage.

4.5.1Transformer:

Usually, DC voltages are required to operate various electronic

equipment and these voltages are 5V, 9V or 12V. But these voltages cannot be

obtained directly. Thus the a.c input available at the mains supply i.e., 230V is to

be brought down to the required voltage level. This is done by a transformer.

Thus, a step down transformer is employed to decrease the voltage to a required

level.

4.5.2Rectifier:

The output from the transformer is fed to the rectifier. It converts A.C. into pulsating D.C. The rectifier may be a half wave or a full wave rectifier. In this project, a bridge rectifier is used because of its merits like good stability and full wave rectification

4.5.3Filter:

Capacitive filter is used in this project. It removes the ripples from

the output of rectifier and smoothens the D.C. Output received from this filter is

constant until the mains voltage and load is maintained constant. However, if

either of the two is varied, D.C. voltage received at this point changes. Therefore

a regulator is applied at the output stage.

4.5.4Voltage regulator:

As the name itself implies, it regulates the input applied to it. A voltage

regulator is an electrical regulator designed to automatically maintain a constant

voltage level. In this project, power supply of 5V and 12V are required. In order

to obtain these voltage levels, 7805 and 7812 voltage regulators are to be used.

The first number 78 represents positive supply and the numbers 05, 12 represent

the required output voltage levels.

Page 25: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

CHAPTER 5 89S52 MICROCONTROLLER

Page 26: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

5.1 Features:• 8K Bytes of In-System Reprogrammable Flash Memory• Endurance: 1,000 Write/Erase Cycles• Fully Static Operation: 0 Hz to 24 MHz• 256 x 8-bit Internal RAM• 32 Programmable I/O Lines• Three 16-bit Timer/Counters• Eight Interrupt Sources• Programmable Serial Channel• Low-power Idle and Power-down Modes

5.2 Description: The AT89C52 is a low-power, high-performance CMOS 8-

bit microcomputer with 8Kbytes of Flash programmable and erasable read

only memory (PEROM). The on-chip Flash allows the program memory

to be reprogrammed in-system or by a conventional nonvolatile memory

programmer. By combining a versatile 8-bit CPU with Flash on a

monolithic chip, the Atmel AT89C52 is a powerful microcomputer, which

provides a highly flexible and cost-effective solution to many embedded

control applications.

Page 27: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

5.3 Pin Diagram - AT89S52:

Fig. 5.1 Pin diagram of 8052.

5.4 PIN DISCRIPTION:

Page 28: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

VCC - Supply voltage.

GND - Ground.

Port 0

Port 0 is an 8-bit open drain bi-directional I/O port. As an

output port, each pin can sink eight TTL inputs. When 1s are

written to port 0 pins, the pins can be used as high-impedance

inputs. Port 0 can also be configured to be the multiplexed low-

order address/data bus during accesses to external program and

data memory. In this mode, P0 has internal pull-ups. Port 0 also

receives the code bytes during Flash programming and outputs the

code bytes during program verification. External pull-ups are

required during program verification.

Port 1Port 1 is an 8-bit bi-directional I/O port with internal pull-

ups. The Port 1 output buffers can sink/source four TTL inputs.

When 1s are written to Port 1 pins, they are pulled high by the

internal pull-ups and can be used as inputs. As inputs, Port 1 pins

that are externally being pulled low will source current (IIL)

because of the internal pull-ups. In addition, P1.0 and P1.1 can be

configured to be the timer/counter 2 external count input (P1.0/T2)

and the timer/counter 2 trigger input (P1.1/T2EX), respectively.

Port Pin Alternate Functions

P1.0 T2 (external count input to Timer/Counter 2), clock-outP1.1 T2EX (Timer/Counter 2 capture/reload trigger and direction control

Port 2

Page 29: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

Port 2 is an 8-bit bi-directional I/O port with internal pull-

ups. The Port 2 output buffers can sink/source four TTL inputs.

When 1s are written to Port 2 pins, they are pulled high by the

internal pull-ups and can be used as inputs. As inputs, Port 2 pins

that are externally being pulled low will source current (I IL )

because of the internal pull-ups. Port 2 emits the high-order

address byte during fetches from external program memory and

during accesses to external data memory that use 16-bit addresses

(MOVX @ DPTR). In this application, Port 2 uses strong internal

pull ups when emitting 1s. During accesses to external data

memory that use 8-bit addresses (MOVX @ RI), Port 2 emits the

contents of the P2 Special Function Register. Port 2 also receives

the high-order address bits and some control signals during Flash

programming and verification.

Port 3

Port 3 is an 8-bit bi-directional I/O port with internal pull

ups. The Port 3 output buffers can sink/source four TTL inputs.

When 1s are written to Port 3 pins, they are pulled high by the

internal pull ups and can be used as inputs. As inputs, Port 3 pins

that are externally being pulled low will source current (I IL )

because of the pull ups. Port 3 also serves the functions of various

special features of the AT89C51. Port 3 also receives some control

signals for Flash programming and verification.

Port Pin Alternate Functions

P3.0 RXD (serial input port)P3.1 TXD (serial output port)P3.2 INT0 (external interrupt 0)P3.3 INT1 (external interrupt 1)P3.4 T0 (timer 0 external input)P3.5 T1 (timer 1 external input)P3.6 WR (external data memory write strobe)

Page 30: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

P3.7 RD (external data memory read strobe).

RST

Reset input. A high on this pin for two machine cycles

while the oscillator is running resets the device.

ALE/PROG

Address Latch Enable is an output pulse for latching the

low byte of the address during accesses to external memory. This

pin is also the program pulse input (PROG) during flash

programming. In normal operation, ALE is emitted at a constant

rate of 1/6 the oscillator frequency and may be used for external

timing or clocking purposes. However, that one ALE pulse is

skipped during each access to external data memory. If desired,

ALE operation can be disabled by setting bit 0 of SFR location

8EH. With the bit set, ALE is active only during a MOVX or

MOVC instruction. Otherwise, the pin is weakly pulled high.

Setting the ALE-disable bit has no effect if the microcontroller is

in external execution mode.

PSEN

Program Store Enable is the read strobe to external

program memory. When the AT89C52 is executing code from

external program memory, PSEN is activated twice each machine

cycle, except that two PSEN activations are skipped during each

access to external data memory.

EA/VPP

External Access Enable (EA) must be strapped to GND in

order to enable the device to fetch code from external pro-gram

Page 31: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

memory locations starting at 0000H up to FFFFH. However, that if

lock bit 1 is programmed, EA will be internally latched on reset.

EA should be strapped to VCC for internal program executions.

This pin also receives the 12V programming enable voltage (VPP)

during Flash programming when 12V programming is selected.

XTAL1:

Input to the inverting oscillator amplifier and input to the

internal clock operating circuit.

XTAL2:

Output from the inverting oscillator amplifier

Page 32: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

5.5 ARCHITECHTURE OF 8052 MICROCONTROLLER:

Fig. 5.2 ARCHITECHTURE OF 8052 MICROCONTROLLER

Page 33: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

5.5.1 Oscillator Characteristics

XTAL1 and XTAL2 are the input and output, respectively,

of an inverting amplifier, which can be configured for use as an

on-chip oscillator, as shown in Figure #3. Either a quartz crystal or

ceramic resonator may be used. To drive the device from an

external clock source, XTAL2 should be left unconnected while

XTAL1 is driven as shown in Figure #4. There are no requirements

on the duty cycle of the external clock signal, since the input to the

internal clocking circuitry is through a divide-by-two flip-flop, but

minimum and maximum voltage high and low time specifications

must be observed.

5.5.2 Idle Mode

In idle mode, the CPU puts itself to sleep while all the on-

chip peripherals remain active. The mode is invoked by software.

The content of the on-chip RAM and all the special functions

registers remain unchanged during this mode. The idle mode can

be terminated by any enabled interrupt or by a hardware reset. It

should be noted that when idle is terminated by a hardware reset,

the device normally resumes program execution, from where it left

off, up to two machine cycles before the internal reset algorithm

takes control. On-chip hardware inhibits access to internal RAM in

this event, but access to the port pins is not inhibited. To eliminate

the possibility of an unexpected write to a port pin when Idle is

terminated by reset, the instruction following the one that invokes

Idle should not be one that writes to a port pin or to external

memory.

Page 34: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

5.6 Oscillator Connections:

Fig. 5.3 Oscillator Connections

Note: C1, C2 = 30 pF ± 10 pF for Crystals = 40 pF ± 10 pF for Ceramic Resonators

Fig. 5.4 External Clock drive Configuration

Page 35: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

CHAPTER 6 IR SENSORS

6.1 IR Remote Control Theory:

Page 36: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

The cheapest way to remotely control a device within a visible range is via Infra-Red light. Almost all audio and video equipment can be controlled this way nowadays. Due to this wide spread use the required components are quite cheap, thus making it ideal for us hobbyists to use IR control for our own projects.

This part of my knowledge base will explain the theory of operation of IR remote control, and some of the protocols that are in use in consumer electronics.

6.2 Infra-Red Light:

Infra-Red actually is normal light with a particular color. We humans can't see this color because its wave length of 950nm is below the visible spectrum. That's one of the reasons why IR is chosen for remote control purposes, we want to use it but we're not interested in seeing it. Another reason is because IR LEDs are quite easy to make, and therefore can be very cheap.

Although we humans can't see the Infra-Red light emitted from a remote control doesn't mean we can't make it visible. A video camera or digital photo camera can "see" the Infra-Red light as you can see in this picture. If you own a web cam you're in luck, point your remote to it, press any button and you'll see the LED flicker.

Unfortunately for us there are many more sources of Infra-Red light. The sun is the brightest source of all, but there are many others, like: light bulbs, candles, central heating system, and even our body radiate Infra-Red light. In fact everything that radiates heat also radiates Infra-Red light. Therefore we have to take some precautions to guarantee that our IR message gets across to the receiver without errors.

6.3 Modulation :

Modulation is the answer to make our signal stand out above the noise. With modulation we make the IR light source blink in a particular frequency. The IR receiver will be tuned to that frequency, so it can ignore everything.

Page 37: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

Fig. 6.1 Modulation

In the picture above you can see a modulated signal driving the IR LED of the transmitter on the left side. The detected signal is coming out of the receiver at the other side.

In serial communication we usually speak of 'marks' and 'spaces'. The 'space' is the default signal, which is the off state in the transmitter case. No light is emitted during the 'space' state. During the 'mark' state of the signal the IR light is pulsed on and off at a particular frequency. Frequencies between 30 kHz and 60 kHz are commonly used in consumer electronics. At the receiver side a 'space' is represented by a high level of the receiver's output. A 'mark' is then automatically represented by a low level.

Please note that the 'marks' and 'spaces' are not the 1-s and 0-s we want to transmit. The real relationship between the 'marks' and 'spaces' and the 1-s and 0-s depends on the protocol that's being used. More information about that can be found on the pages that describe the protocols.

6.4 The Transmitter :

Fig. 6.2 IR Transmitter

The transmitter usually is a battery powered handset. It should consume as little power as possible, and the IR signal should also be as strong as

Page 38: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

possible to achieve an acceptable control distance. Preferably it should be shock proof as well.

Many chips are designed to be used as IR transmitters. The older chips were dedicated to only one of the many protocols that were invented. Nowadays very low power microcontrollers are used in IR transmitters for the simple reason that they are more flexible in their use. When no button is pressed they are in a very low power sleep mode, in which hardly any current is consumed. The processor wakes up to transmit the appropriate IR command only when a key is pressed. Quartz crystals are seldom used in such handsets. They are very fragile and tend to break easily when the handset is dropped. Ceramic resonators are much more suitable here, because they can withstand larger physical shocks. The fact that they are a little less accurate is not important.

The current through the LED (or LEDs) can vary from 100mA to well over 1A! In order to get an acceptable control distance the LED currents have to be as high as possible. A trade-off should be made between LED parameters, battery lifetime and maximum control distance. LED currents can be that high because the pulses driving the LEDs are very short. Average power dissipation of the LED should not exceed the maximum value though. You should also see to it that the maximum peek current for the LED is not exceeded. All these parameters can be found in the LED's data sheet.

A simple transistor circuit can be used to drive the LED. A transistor with a suitable HFE and switching speed should be selected for this purpose. The resistor values can simply be calculated using Ohm's law. Remember that the nominal voltage drop over an IR LED is approximately 1.1V. The normal driver, described above, has one disadvantage. As the battery voltage drops, the current through the LED will decrease as well. This will result in a shorter control distance that can be covered.

An emitter follower circuit can avoid this. The 2 diodes in series will limit the pulses on the base of the transistor to 1.2V. The base-emitter voltage of the transistor subtracts 0.6V from that, resulting in constant amplitude of 0.6V at the emitter. This constant amplitude across a constant resistor results in current pulses of a constant magnitude. Calculating the current through the LED is simply applying Ohm's law again.

Page 39: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

6.5 THE RECEIVER :

Fig. 6.3 IR Receiver

Many different receiver circuits exist on the market. The most important selection criteria are the modulation frequency used and the availability in your region.

Fig. 6.4 Block diagram of such an IR Receiver

In the picture above you can see a typical block diagram of such an IR receiver. Don't be alarmed if you don't understand this part of the description, for everything is built into one single electronic component.

The received IR signal is picked up by the IR detection diode on the left side of the diagram. This signal is amplified and limited by the first 2 stages. The limiter acts as an AGC circuit to get a constant pulse level, regardless of the distance to the handset. As you can see only the AC signal is sent to the Band Pass Filter. The Band Pass Filter is tuned to the modulation frequency of the handset unit. Common frequencies range from 30 kHz to 60 kHz in consumer electronics. The next stages are a detector, integrator and comparator. The purpose of these three blocks is to detect the presence of the modulation frequency. If this modulation frequency is present the output of the comparator will be pulled low. As I said before, all these blocks are integrated into a single electronic component. There are many different manufacturers of these components on the market. And most devices are available in several versions each of which are tuned to a particular modulation frequency.

Page 40: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

Please note that the amplifier is set to a very high gain. Therefore the system tends to start oscillating very easily. Placing a large capacitor of at least 22µF close to the receiver's power connections is mandatory to decouple the power lines. Some data sheets recommend a resistor of 330 Ohms in series with the power supply to further decouple the power supply from the rest of the circuit.

There are several manufacturers of IR receivers on the market. Siemens,

Vishay and Telefunken are the main suppliers here in Europe. Siemens has

its SFH506-xx series, where xx denotes the modulation frequency of 30,

33, 36, 38, 40 or 56 kHz. Telefunken had its TFMS5xx0 and TK18xx

series, where xx again indicates the modulation frequency the device is

tuned to. It appears that these parts have now become obsolete. They are

replaced by the Vishay TSOP12xx, TSOP48xx and TSOP62xx product

series. Sharp, Xiamen Hualian and Japanese Electric are 3 Asian IR

receiver producing companies. Sharp has devices with very cryptic ID

names, like: GP1UD26xK, GP1UD27xK and GP1UD28xK, where x is

related to the modulation frequency. Hualian has it's HRMxx00 series, like

the HRM3700 and HRM3800. Japanese Electric has a series of devices

that don't include the modulation frequency in the part's ID. The PIC-

12042LM is tuned to 36.7 kHz, and the PIC12043LM is tuned to 37.9 kHz

IR Advantages:

Low power requirements: therefore ideal for laptops, telephones, personal digital assistants

Low circuitry costs: $2-$5 for the entire coding/decoding circuitry Simple circuitry: no special or proprietary hardware is required, can be

incorporated into the integrated circuit of a product Higher security: directionality of the beam helps ensure that data isn't leaked or

spilled to nearby devices as it's transmitted Portable Few international regulatory constraints: IrDA (Infrared Data Association)

functional devices will ideally be usable by international travelers, no matter where they may be

High noise immunity: not as likely to have interference from signals from other devices

Page 41: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

IR Disadvantages:

Line of sight: transmitters and receivers must be almost directly aligned (i.e. able to see each other) to communicate

Blocked by common materials: people, walls, plants, etc. can block transmission Short range: performance drops off with longer distances Light, weather sensitive: direct sunlight, rain, fog, dust, pollution can affect

transmission Speed: data rate transmission is lower than typical wired transmission

Page 42: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

CHAPTER 7 RELAY DRIVER CIRCUIT

Page 43: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

RELAY CIRCUIT:

Fig. 7.1 Relay

A single pole dabble throw (SPDT) relay is connected to port RB1 of the

microcontroller through a driver transistor. The relay requires 12 volts at a

current of around 100ma, which cannot provide by the microcontroller. So

the driver transistor is added. The relay is used to operate the external

solenoid forming part of a locking device or for operating any other

electrical devices. Normally the relay remains off. As soon as pin of the

microcontroller goes high, the relay operates. When the relay operates and

releases. Diode D2 is the standard diode on a mechanical relay to prevent

back EMF from damaging Q3 when the relay releases. LED L2 indicates

relay on.

Page 44: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

CHAPTER 8 SOURCE CODE

Page 45: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

#include#include#define LCD_clear() LCD_command(0×01) /* Clear LCD Display#define LCD_orgin()LCD_command(0×02) /* set to orgin LCD#define LCD_row1() LCD_command(0×80) /* Begin at 1st line#define LCD_row2()LCD_command(0xc0) /* Begin at 2nd line

sbit port10=P1^0; //IR Sensor Inputsbit rs=P3^6; //Lcd Register Select Pinsbit en=P3^7; //Lcd Enable Pin

static unsigned char counter;

void lcd_en() //Funtion for LCD Enable{en=1;en=0;}

void LCD_delay(unsigned char ms) //Function for create Time Delay{unsigned int n,i;for(n=0;n<ms;n++) {for(i=0;i<1536;i++);}}</ms;n++)

void LCD_command(unsinged char command) //LCD Command Pass Funtion{rs=0;P0=command;lcd_en();LCD_delay(1);}void LCD_init() //LCD intialization funtion{LCD_command(0x38);LCD_command(0x06);LCD_command(0x0c);LCD_command(0x01);}void LCD_putc(unasigned char ascii){rs=1;P0=ascii;lcd_en();LCD_delay(2);}

Page 46: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

void LCD_puts(unsigned char *lcd_string){while(*lcd_string){LCD_putc(*lcd_string++);}}void disp(unsinged char name1){rs=1;P0=name1;lcd_en();lcd_delay(300);}void main(){port10=0; //make P1.0 as init=0, initially all port pins are highP2=0; //make low for P2LCD_init(); //call LCD initialization functionwhile(1) //Run forever always true{if(port10) //check condition P2.0 is high P2.0==1{LCD_command(0x80); //LCD command for display first lineLCD_puts("visit count="); //String display in the LCD{disp(((counter%10000)/1000)+48);disp(((counter%1000)/100)+48);disp(((counter%100)/10)+48);disp(((counter%10)/1)+48);}}P2=counter; // 8 LED's conneted in PORT 2LCD_comman(0xc0) //LCD command for display 2nd line}}

Page 47: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

CHAPTER 9 FUTURE EXPANSION

Page 48: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

By using this circuit and proper power supply we can implement various

applications

Such as fans, tube lights, etc.

By modifying this circuit and using two relays we can achieve a task of

opening and closing the door.

Page 49: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

CHAPTER 10 APPLICATIONS, ADVANTAGES & DISADVANTAGES

Page 50: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

Applications For counting purposes

For automatic room light control

Advantages Low cost

Easy to use

Disadvantages It is used only when one single person cuts the rays of the sensor hence

it cannot be used when two person cross simultaneously.

Page 51: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

CHAPTER 11 REFERENCES

Page 52: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with

1. Embedded Systems - Raj Kamal

2. www.wikipedia.com

3. INFRARED DETECTORS AND EMITTERS – Peter capper and C.T.Elliot

4. http://www.embed4u.com

Page 53: 3.2 Characteristics: - Latest Seminar Topics for · Web viewTITLE AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER ABSTRACT This Project “Automatic Room Light Controller with