323200961422pmmicrosoft word - chapter viii
TRANSCRIPT
-
8/11/2019 323200961422PMMicrosoft Word - Chapter VIII
1/14
225
CHAPTER VIIIRUNNING AND MAINTENANCE OF MACHINERY
8.1 The entire machinery and equipment of the Corporation pertaining toconstruction works of buildings, roads and bridges including tippers and trucks will
be in the charge of the mechanical unit at the head office, headed by a ResidentEngineer (Mechanical). In addition to the work of purchase, running andmaintenance of construction machinery and equipment, the RE (Mechanical) willalso be responsible for purchase running and maintenance of office vehicles (cars,
jeeps, etc.) located at the headquarters. The R&M includes upkeep of logbooks ofthese machinery and vehicles, periodical and urgent repairs, etc.
8.2 The ownership record of all the machinery and equipment, old andnew will be kept in the Equipment Register. It will contain basic data about themachine/equipment/vehicle regarding its make, purchase cost, economic life inyears/hours, details of spare parts received with the machine and expenditure
incurred on major repairs, replacement of tyres, depreciation charged, etc., from timeto time.
8.3 Running and maintenance estimate of each machinery, equipment andvehicle will be prepared by Mechanical Unit every year before commencement of thefinancial year to account for expenditure on operation and return from out turn. Thedirect operating charges on a machine including repairs, cost of spares, etc., will bedebited to the estimate while the value of out turn in the form of hourly or daily orunit rate or per kilometre rate charged will be credited to the estimate. However, inthe case of office vehicles there will be no out turn.
8.4 Record of issue of logbooks for each machine, equipment or vehiclewill be kept in a logbook register and through this a watch on proper use and returnof the logbooks for preparation of debit/credit notes or for record will be kept. Thelogbooks shall be checked to watch that:(i) the monthly abstract of use of the machinery on various works/purposes has
been correctly prepared and the amount to be charged from various users hasbeen clearly shown;
(ii)
the rate of consumption of POL is within the norms of standardconsumptions;
(iii)
all parts of the logbook have been properly filled-in and signed by theauthorised user;
(iv)
entries of POL, minor and major repairs with spares have been made in it;(v) issue of the machinery to the contractors has been distinctly shown so that
rates prescribed for outside users may be charged.
8.5 Each year, hourly/unit rate of each construction machine to be chargedto the work and to the contractors/outside parties will be worked out and fixedbefore commencement of the financial year in accordance with the guidelines givenby the Ministry of Surface Transport, Government of India and the economic liferecommended by them for various types of machinery. A model work sheet for
-
8/11/2019 323200961422PMMicrosoft Word - Chapter VIII
2/14
226
computation of unit rate of hire charge is given at Annexure-VIII A. The unit rateshould be within the market rate of similar type of machine. Economic life forvarious types of machinery recommended by Ministry of Surface Transport,Government of India, vide their letter No. RW-24011/5/93-R&P dated December 30,1993 is given at Annexure VIII B. A list of various types of machinery, equipmentand vehicles being maintained presently by the Mechanical Unit is given atAnnexure VIII C. It includes hot mix plants, paver finishers, vibratory compactors,road roller, DG sets, trucks, tippers, jeeps, cars, etc. The present rates of hire chargesof machinery of the Corporation is given at Annexure VIII D.
8.6 Every month the logbook of each machine duly filled-in and signed bycompetent authorities of Construction Units will be sent to the RE (Mechanical) forchecking and raising of debit notes. A set of two logbooks for a machine for use inalternate months may be kept to avoid delay in raising of bills. The engineer-in-charge of the machine will make out an abstract of use of the machine during themonth giving the names of works, hours or units of use, transportation charges, rate
per unit of use (hour, kilometre, ton) and the total amount to be charged. TheAccountant/AAO of Mechanical Unit will check the entries of the logbook, monthlyabstract and get prepared a debit/credit note to be sent to each user RE ofConstruction Unit or to the contractor or other user.
8.7 The Auditor, Accountant/AAO and RE (Mechanical) will sign thedebit notes alongwith the bills and will forward them to the concerned REs ofConstruction Units alongwith extract copy of the logbook. In the accounts ofMechanical Unit the respective users accounts will be debited and the M&Restimate of the machine (hire charges) will be credited. The direct charges like costof POL, Salary/Wages of operators, minor repairs, etc. will also be debited to the
M&R estimate of the machine. The formats of bill, debit note and forwarding letter isgiven at Annexure VIII-E.
8.8 The construction division on receipt of the debit note will check thedemand with respect to the copy of logbook, site record and sign the counterfoil ofthe debit note and send it back to the RE (Mechanical) alongwith cheque/DDdebiting the work concerned within 15 days of receipt of the debit note. If there is adiscrepancy in the debit note and actual use of machine hours/units or rate, thecheque/DD for accepted amount shall be sent and for the remaining amountclarification note will be sent by the RE of the Construction Unit. Any expenditureincurred by the Construction Unit on the R&M and POL of the machine will be
deducted from the bill.
8.9 Minor repairs, special repairs, replacement of tyres/spare parts ofmachinery will be done at the central workshop at the Head Office, debiting theM&R estimate of the machine. However, emergent repairs may be got done at thesite of work by the Construction Unit in consultation with RE (Mechanical) debitingthe expenditure to the account of RE (Mechanical). Periodic repairs, major repairs ofoffice cars and jeeps may be got done at the central workshop, if the facility exists or
-
8/11/2019 323200961422PMMicrosoft Word - Chapter VIII
3/14
227
at authorised dealers workshops. Minor repairs of these vehicles may be got done atthe central workshop or at the local market upto Rs. 2,000/- in each case. The officevehicles located at places outside Jaipur may be got repaired at authorised dealersworkshop at the respective place except minor repairs costing upto Rs. 2,000/- at atime which may be got done at local market. Spare parts used in repairs shall,however, be purchased always from the authorised dealer or equipmentmanufacturer or sole distributor as per purchase rules.
8.10 Every year, the month-wise utilisation of each constructionmachine/equipment will be compiled by the Mechanical Unit and it will becompared with the annual utilisation norms and a report in this regard will besubmitted to the MD by RE (Mechanical) with comments of SE, GM/CPM and CAOfor directions for further course of action.
8.11 The machine which is not being used upto the normal utilisation units(hours/km/ton) in a year should be reviewed to find reasons of under-utilisation. If
it is due to its obsolescence or oldness or surplus nature, it should be considered fordisposal. The Corporation should not run a machine which causes loss to it, being acommercial organisation.
8.12 Every year a survey report of the unserviceable/obsolete machinerywill be prepared by Mechanical Unit for orders of MD for their disposal. Theoperating staff rendered surplus due to disposal of machinery should be dealt within accordance with personnel policy of the Corporation and general guidelines givenby the Government in this regard.
-
8/11/2019 323200961422PMMicrosoft Word - Chapter VIII
4/14
228
Annexure VIII-ARAJASTHAN STATE ROAD DEVELOPMENT & CONSTRUCTION
CORPORATION LTD, JAIPUR
NAME OF EQUIPMENTS:1. FOR EQUIPMENT USED DEPARTMENTALLY(I) Ownership charges:(a) Total investment at site of work (this includes A/T cost,
sales tax, excise, custom and other duties, transportexpenses consisting of freight (by ocean & rail) insuranceloading/unloading charges and erection andcommissioning on receipt)
Rs
(b) Deduct salvage value@15 percent of A Rs(c) Total investment to be depreciated = A-B Rs(d) Economic life of the machine in hours as per appendix 7.II
(as per Ministry norms, it is 9000 Hrs.)Hrs. Rs
(e) Depreciation per hour [ C/D ] Rs(f) Storage charges per hour (1 percent of c spread over theeconomic life) = 0.01x (C) / (D)Total ownership charges = (E)+ (F) RsI
II Operational ChargesRepair charges per hour including maintenance andreplacement of tyres (150 percent of C spread overeconomic life = 1.5xC/D
RsII
III Overhead Charges:@ 5 percent of ownership and operational charges= 5(1+II)/100
Ownership charges per hoursOperational Charges per hours = Rs.III
Overhead charges per hours = Rs..IV Running Charges:
Operating staff/labour & wages: No. Wages/monthDesignation(i) Operatior(ii)
Helper(iii) Cleaners(iv)
Misc. Expenses (Welder)
(v)
TA. Etc. Total = Rs. ..(H) Wages Per hour Total Wages per monthx12
Annual working hours(See note d)
= Rs. ..
(J) Servicing charges: No. Expenditure/MonthDesignation(i)
Machine(ii) Cleaners(iii)
POL Total = Rs..
-
8/11/2019 323200961422PMMicrosoft Word - Chapter VIII
5/14
229
(J) Servicing Chages: Fuel Lubricants, etc.Consumption/hr. Rate/Litre Cost/hr.(i) Fuel(ii)
Lubricants(iii)Grease(iv)
Hyd. Oil(v)
Gear Oil, Cotton waste, etc.Furnace oil etc. (in case of Hot mix plant, etc.) Total Rs
K Cost of Lub. Oil, Fuel etc. hr.L Total Running charges per hour = H + J + KV. Overhead charges @ 5 percent of the total charges
per hour = 5 x L/100 = RsSumming up:Ownership charges = I =Operational Charges = II =Overhead of I and II = III =
Running charges (as in 5) = IV =Overhead charges on IV = V =Hire charges per hour= I+II+III+IV+V
2. For equipment given to contractors & outside agencies:When the machines are issued to contractors interest and insurance charges @ 10percent of average investment per year will be calculated as under and added
A 60* 10+ --------------------------- * one- 5 years life
1500 100 100
-
8/11/2019 323200961422PMMicrosoft Word - Chapter VIII
6/14
230
Annexure-VIII- BEconomic Life of Raod/Bridge Construction Equipment
S.N. Name of Machine Years Km./hrs.
I. Bittumenous Construction Equipment
1. Hot Mix Plant (Below 20 TPH) 12 9000 hrs.2. Hot Mix Plants (Above 20 TPH) 12 9000 hrs.3. Drum Mix Plants 12 9000 hrs.
4. Paver Finisher 15 9000 hrs.5. Bitument Boilesrs 10 ---
6. Bitumen Pressure Distributor/ BitumentTransportaion Tanker
12 9000 hrs.
7 Bitumen Storage Tank 10 ----
8. Asphalt Mixer 12 8000 hrs.9. Front End Loader (Wheeler) 15 9000 hrs.
10. Tippers 12 2,40,000 km.
11. Chip Spreadoer 10 ---II. Heaver Earth Moving Equipment
1. Dozer Wheeled 15 9000 hrs.
2. Dozer Creqler 15 9000 hrs.
3. Motorised scraper/ Towed screper 15 9000 hrs.
4. Motor Grader 15 9000 hrs.
5. Excavator upto 1 cum 12 10000 hrs.
6. Mobile Crane 15 8000 hrs.7. Cumper (All size) 12 1000 hrs.
8. Tractor (Wheeled) 12 1000 hrs.9. Grab Dredging Cranes 12 9000 hrs.
III COMPACTION EQUITPMENT1. Road Roller 8-10T 15 12000 hrs.
2. Sheep foot Roller 15 ---3. Vibratory Rollers upto 2 tons WT 10 ---
4. Vibratory Rollers above 2 tons WT 12 10000 hrs.
5. Tandem Vibratory Roller 8-10T 12 10000 hrs.
6. Pneumatic Tyred Rollers 12 10000 hrs.
IV1.
BRIDGE CONSTRUCTION EQUIPMENT
Bridge Inspection Unit(a) Bucket Type
(b) Platform Type
15
18
---
---
2. Power Winch 15 8000 hrs.3. Concrete Mixer 06 ---
4 Pile Driving Set 12 8000 hrs.5. Diamond Core Drill Pm/C 12 8000 hrs,
6. Vibrators (all types 05 ---7. Air Compressor 12 9000 hrs.
8. Pumping set Diesel (upto 10 HP) 08 ---
-
8/11/2019 323200961422PMMicrosoft Word - Chapter VIII
7/14
231
9. Pumping Set Diesel (Above 10 HP) 12 10000 hrs.
10. Winch Bridges 12 ---
V.1.
GENERAL PURPOSETruck 12 2,40,000 km.
2. Stone Crusher/Granulator (Electrical) 15 12000 hrs.
3. Stone Crusher/Granulator (Diesel) 12 10000 hrs.4. Generator Set 12 10000 hrs.
5. Diesel Welding Set 15 10000 hrs.
6. Jeep/Car/Station Wagon/Mini Bus 10 2,00,000 kms.7. Ferry/Boate- Steel 15 ---
Wooden 10 ---8. Kerb Laying Machine 12 ---
9. Concrete Transit Mixer 12 10000 hrs.10. Concrete Pump 10 ---
11. Concrete Batching & Mixing Plant 15 12000 hrs.
12. Concrete Paving Equipment 15 12000 hrs.13. Stone Crushing & Screening Unit 10 10000 hrs.
14 Snow Cutter/Plougher 20 ---
-
8/11/2019 323200961422PMMicrosoft Word - Chapter VIII
8/14
232
Annexure VIII-C
POSITION OF MACHINES/VEHICLES AS ON DATED 30.6.2006
S.N. Name of Machines Number
1 Hot Mix Plant 05 (1 acutioned)2 Paver Finishers (Mechanical) 08
3 Sensor Paver Finisher 014 Concrete Batch Mix Plant 01
5 Transit Mixer 016 Wet Mix Plant 01
7 Vibratory Compactor Tandon Type W-752 018 Vibratory Earth Compactor Dynapac 01
9 Diesel Road Rollers 8-10T 0210 JCB Excavator Loader 01
11 Tata Excavator (Crane) 03
12 Bitumen pressure Distributor 0113 Tractors 03
14 Vacuum Dewatering Systems 04
15 DG Sets Diff Range (7.5 to 125 KVA 22
16 Trailor (Long Bed) 02
17 Trucks 04
18 Tippers 21
19 Jeeps 05 (1 auctioned)20 Ambassador Car 02
21 Indica Carq 0222 Santro Car 01
23 Esteem Car 0224 Bolero Jeep 03
-
8/11/2019 323200961422PMMicrosoft Word - Chapter VIII
9/14
233
Annexure VIII-D
HIRE CHARGES RATES OF CORPORATION MACHINESEFFECTIVE FROM 1.4.1997 ONWARDS
S.N Machine Rates forCorporation(Rupees)
Forcontractor(Rupees)
Unit
1. Vibratory Compactor (Soil) 470 490 Per Hours
2. Diamond Core Drilling Machine 170 220 Per Hour3. Power Winch 30 35 Per Hour
4. Builders Hist. 705750
806720
Per HourPer Month
5. Well Point Dewatering Pump Set 105 130 Per Month
6. JCB Excavator Loader 400 480 Per Hour
7. DG Set 7.5 to 10 KVA 40 45 Per Hour
8. DG Set 18 .75 KVA 60 65 Per Hour9. DG Set 25 KVA 90 100 Per Hour
10. DG Set 62.5 KVA 185 200 Per Hour
11. DG Set 100 KVA 220 250 Per Hour
12. DG Set 125 KVA 250 300 Per Hour
13. Sensor Power 1315 -- Per Hour
14. Vibratory CompactorSteel/Wheel) Vibromax (L & T)
780 -- Per Hour
15. Tipper Trucks 740 Or -- Per DayWithout Pol 7.60 P Per Km.
With Pol 860 Or Rs. Per Km.
16. Millar 15 Cu.m/Hour-Concrete Batching Plant 320 495 Per Hours
-Without Electric Charges 275 455 Per Hour
17. Drum Mix HKP (40-60 TPH)- With Electric Charges 2810 3315 Per Hour- Without Electric Charges 1040 1515 Per Hour
18. Bitumen Pressure Distributor 390 --- Per Hour
19. Diesel Power Winch 110 130 Per Hour
20. TATA Crane Model 320 18 Mt.
Capacity
450 650 Per Hour
21 TATA Crane Model 655 36 MTCapacity
550 700 Per Hour
22 Air Compressor 300 CFM. 110 140 Per Hour
23. Air Compressor 400 CFM 155 205 Per Hour
24. Stone Crusher 95 120 Per Hour
25. Hindustan Tractor 50 HP 65 75 Per Hour
26 Concrete Mixer 10/7 CFT. 50 55 Per Hour
27. Apollo HMP (20-30 TPH)
-
8/11/2019 323200961422PMMicrosoft Word - Chapter VIII
10/14
234
With POL 2530 -- Per Hour
Without POL 610 -- Per Hour
28. Concrete Mixer 14/10 CFT 55 70 Per Hour
29. Winch With HMP (Grit Pushing) 0.00 -- Per Tonne
30. Transit Mixer Millar With POL 630 -- Per Hour
31. Beaver Trailor With POL 2420 -- Per Day32. Vacuum Dewatering System 8800 -- Per Month
33. Vibratory Roller 1 to 2 Tonnes 5225 -- Per month34. SU Dewatering Pumps 3000 -- Per Month
35. Hilti Core Cutting Machine 12000 -- Per Month36. Diesel Road Roller 8-10 Tonne 80 180 Per Hour
37. Mastic Cooker 120 135 Per Hour38.
(i)
Hot Mix Plant (40-60 TPH) withallied equipment on 1 MTproduction BasisMix Material at Plant Site
120
78
135
--
Per Hour
Per Metric
Tonne(ii) Mix Material with
Transportation within Municipallimits
123 --- ---
(iii) Mix Material withTransportation ConventionalPower-Roller within MunicipalLimits
152 -- --
(iv) Mix Material with transportationSensor Power-Vibromax withinMunicipal Limits
177 -- --
(For Outside Municipal Limits Rs. 10/- or more according to distance may becharged per tonne more as the case may be)
Resident EngineerMech_I
RSRDC., Jaipur
-
8/11/2019 323200961422PMMicrosoft Word - Chapter VIII
11/14
235
Phones: 0141-2711162 (o) Telefax : 0141-2711178
Rajasthan State Road Development Construction Corporation Ltd.,(Formerly RSBCC Ltd.)
(A Government of Rajasthan Undertaking)Reg Office: Setu Bhavan, Jhalana Doongari Jaipur Agra By-Pass Road, Jaipur
(Mechanical Unit)
A-5 (M)/Hire Charges/1247-51 Dated 7.1.2006
Office Order
The hire charges of Hot Mix Plant & allied Machinery for Mixing the material,transportaion & Compaction are as follows:
1. Hire Charges of HMP & Allied machines : Rs. 299/pmt.The above rates are fixed with the following conditions:
(i)
These rates are valied for a lead of 25 km. Only. IF the lead increased, the POLcomponent of transportation charges will be charged extra.(ii)
If the rates of LDO & HSD increases, POL component of hire charges will becharged accordingly.
(iii)
The shifting charges, transportation charges, erection & Commissioiningcharges, loading & unloading charges of HMP etc will be charged extra.
(iv)
All civil works for erection purpose will be carried out by civil wing ald alsoto be borne by concrened civil unit.
(v) Feeding aggregates, laying of mix material will be charged extra as peractuals.
(vi) Hire charges of miscelleneous machies like 7.5 KVA DG set for lighting, JCB
for other activites will be charged as per norms.(vii) For any other miscelleneous activity, the hire charges will be extra.
This bears approval of Managing DirectorRESIDENT ENGINEER (Mech.)
Copy to:1.
SE-I, RSRDC Ltd., Jaipur2. SE, RSRDCC, Ltd., Jaipur3. Resident Engineer, RSRDC, Ltd., Unit Hanumangarh4. Shri M.L. Arora, A.En. (Mech.) RSRDCC, Ltd., Jaipur5. Accountant (Mech) RSRDCC., Jaipur
Resident Engineer (Mech.)
-
8/11/2019 323200961422PMMicrosoft Word - Chapter VIII
12/14
-
8/11/2019 323200961422PMMicrosoft Word - Chapter VIII
13/14
237
RAJASTHAN STATE BRIDGE & CONSTRUCTION CORPORATION LTD.(a Government of Rajasthan Undertaking)
Debit/Credit Note
No.
Resident EngineerUnit.
Referenceof LogBookNo./CVNo.
Details of Debit/Credit Claims Total usein no. ofunits
Rate PerUnit
Amount
Prepared by Checked by Total
Auditor Accountant AAO Resident EngineerRSRDCC, Ltd.
-----------------------------------------------------------------------------------------------------------
DEBIT/CREDIT NOTE
No.
Returned to H.O. with remarks that the Debit/Credit note has beenAccepted subject to following deficiencies
ACCOUNTANT/R.E.UNIT---------------
Bill No.
-
8/11/2019 323200961422PMMicrosoft Word - Chapter VIII
14/14
238
OPERATIONAL DETAILS OF CORPORATION MACHINERY UNDERRESIDENT ENGINEER
S.N. Name ofMachinery
CorporationSerial No.
OperationalHours
HourlyRate
Amount
(Rs.. Only)
AAO (Mech.) Resident Engineer (Mech.)
Debit Note No:.