Inhale, Exhale, Relax[Triple Safety with the Advantage Line]

2 ] 3

Advantage 3100 with Gas Filter ABEK

Advantage 3200 with TabTec® Gas Filter

Clean air for breathing is essential for life.So nothing is more important than cleanair – especially if you have to work in acontaminated atmosphere.

Our philosophy is simple and effective:Comfortable protection for people isalways the prime goal, and optimal safetyis the highest priority at MSA. But thecomfort of a respirator is at least equallyimportant because if your respirator isuncomfortable you cannot concentratefully on your work, and that endangersyour safety.

But the right type of respiratory protectiondepends on the particular situation.If there are hazards that also irritate orharm the eyes, you need a mask whichcovers your entire face and thus protectsboth respiratory tract and eyes.

The MSA Advantage 3000 series of fullface masks sets new standards forprotection and unparalleled comfort. Thisinnovative full face mask was developedto meet the high quality standards inEurope and North America.

With the Advantage 3000 and Advantage 200 LSmasks, as well as the TabTec® Filter Technology,MSA has introduced three different respiratoryprotection devices on the market andestablished a technology lead.

MSA Advantage 3000[ Safety that fits]

[ Smart Protection]

Put your chin into the chin stop Pull the straps over your head

Tighten the straps

The Advantage 3000 isavailable with single EN ortwin Advantage filter ports

Depending on the application andindividual head size, everybody has his or her own requirements when it comesto respiratory protective equipment.In order to meet every requirement, theAdvantage 3000 comes in two versions,each with three different sizes.The Advantage 3000 is available for singleor twin filters, which means that both the classic filter with EN 148 standardthread or the Advantage filter series canbe used.

The Advantage 3000 is incredibly quick toput on and simple to handle. Holding themask with one finger, you put your chininto the chin stop and pull the harnessover your head. Then you tighten the twolower straps. If necessary, you can adjustthe upper side straps before putting onthe mask. This makes it quicker andsimpler, without any painful hair pulling.

Even men with beards canbenefit of a better protection with the Advantage 3000 because the newpatented Advantage head harnessguarantees a perfect facepiece-to-face fit.

Apart from functional efficiency we havealso paid special attention to appearance.The narrow design is one feature. A large,optically corrected eye glass ensures clear,undistorted vision, while the grey-bluecolour gives the mask an aestheticappearance.

As we said, the MSA Advantage 3000 isavailable in different versions and sizes.To simplify your choice of the right model,we have assigned each model 4-digits:� The first digit “3” identifies the

3000 series.� The second digit stands for the number

of filters [1 for EN 148, 2 for bayonet].� The third digit indicates the size

[1 = small, 2 = medium, 3 = large].� The fourth digit identifies the head

harness [1 for the Advantage harness,2 for the Advantage harness with silicon straps].

Like the Advantage 200 LS, the Advantage 3000 can be fitted with thelatest in filter technology.

[ The Right Size for Every User]

[ Easy Fittings]

[ Attractive Design]

[ The Ideal Mask for Every User]

4 ] 5

The Advantage 200 LS respirator

MSA has improved the Advantage 200respirator even further. The result is the high-performance, economic and easy to handleAdvantage 200 LS respirator.

Working with production materials andhandling chemical products requires the useof respiratory protective equipment. For thisreason optimal respiratory protection for themany different hazardous substances isessential.This applies to emergency situationsas well as to precautionary measures atwork or in situations where health-endangering gases or substances arereleased.

The “feel good factor” is also essential. If your mask does not fit exactly, not only thequality of your work suffers, but safety isalso endangered.

MSA makes a mask that surpasses all pre-vious comfort criteria.Our Advantage 200 LS with its filtertechnology meets every requirement ofmodern respiratory protection. Therespirator is extremely safe, exceptionallycomfortable and incorporates the latesttechnology. Furthermore, it is characterisedby light weight, minimum breathingresistance and uncomplicated handling.Especially the modified nose area and amplydimensioned chin and cheek sections ensurea comfortable and pressure-free fit.

MSA Advantage 200 LS[ Comfortable Respiratory Protection –

Light and Safe]

The convenient belt pouch isideal for storing and carryingthe Advantage 200 LS and its filters

Advantage 200 LS with FLEXIfilter The facepiece-to-faceAnthrocurve

The Advantage 200 LS protects againstdirt, dust and hazardous gases. The maskis suitable for every area of use, whetherin industry, craft trades or DIY. With itsexcellent facepiece-to-face fit, it providesmaximum protection and offers greatlyimproved wearing comfort.

The Advantage 200 LS consists of the facesection, a 4-point yoke, the inhalation andexhalation valve and the head harness. Inaddition, it is fitted with various particle,gas and combined filters.

MSA’s engineers have developed theunique facepiece-to-face Anthrocurve,which fits the user’s face contourswithout any problem. This means evengreater safety plus a faultless fit. Therespirator is available in three differentsizes.

As a result of continual productimprovement, the Advantage 200 LS isextremely comfortable thanks to itsflexibility, light weight and 4-pointharness. The ingenious Multiflex systemis unique in the market. The plasticcomponents are embedded in a softmaterial, thus making the face sectionelastic and robust.

For storage and transport of the mask,the Advantage belt pouch provides aperfect solution.

Particle, Gas andCombination Filters for the Advantage 200 LS

[ Universal: The Applications]

[ Comfortable: The Fit]

[ Optimised: The Design]

[ Flexible: The Use]

6 ] 7

Advantage 3200 with TabTec® and FLEXIfilters

The masks in the Advantage series are fittedwith the innovative TabTec® and FLEXIfilters.These filters protect against toxic gases,vapours and particles.

TabTec® from MSA is a revolutionary filter technology – compact, flexible andenvironment friendly.

Traditional filters use carbon granules in a filter housing. TabTec® uses a carbontablet – hence the name TabletTechnology.The performance of the filter is as high asever, but now the filter is more flexibleand compact because weight, volume andenvironmentally harmful materials havebeen reduced to a minimum. The new Tab Technology is simple and effective.It eliminates the need for a filter housingthus permitting a compact and light-weight design.

The TabTec® Advantage Filter is availableas A1, A2 and A2B2E1K1, and is approved according to EN 141. With anadapter, combination filters are alsopossible, either with P2 or P3 FLEXIfilter.

MSA TabTec® and FLEXIfilter[ Simple and Effective – Pure Air]

[ Revolutionary: TabTec®]

Protection against dust andparticles: The FLEXIfilter

Tab Technology

TabTec® with FLEXIfilters TabTec® Filter in Detail

Advantage 200 LS with FLEXIfilter

Advantage 3200 with TabTec® Filter

Gas filters against toxic or odourlessgases must be replaced after a single use.The end of the service life of particlefilters becomes apparent when breathingresistance increases.

The FLEXIfilter is a highly innovativeparticle filter. With its flat design, hardlynoticeable breathing resistance and lightweight, it offers unsurpassed comfort.

The FLEXIfilter is approved for protectionagainst dust according to EN 143. It isavailable in the filter classes P2, P3, P2 ORand P3 OR [Odour Removal]. The filtermaterial is assembled according to classand performance. To eliminate unpleasantodours, thin layers of charcoal materialare added. These versions are tested for 5 times the ozone threshold limit valuefor 8 hours.

The FLEXIfilter is suitable for applicationswhere particle aerosols and odours occur.Since the filters fit well under a welder’shood, they are used by many welders.

The service life of respiratory filtersdepends on the ambient atmosphere, theuser and the conditions of use. Gas filtersmust be replaced at the latest whenodour, taste or irritation is detected.

[ Innovative: FLEXIfilter]

8 ] 9

10

4

1

11

48

5

13

12

2

6

9

With its exclusive design, the Advantage 3000is one of the easiest-to-use masks on themarket. It solves all comfort problems and itsmaintenance is easy to learn. All componentscan be replaced without tools in a matter ofseconds.

MSA Advantage 3000[ Safety and Simplicity]

Advantage 3000 withGas Filter ABEK

Advantage 3000with TabTec® Filters

7

3

6

14

Advantage Container

The Advantage Container is designed forthe new Advantage 3000 full face maskseries, but can also be used with ALL masksin the MSA range. It provides new, uniquefeatures: a special recess and a wall bracket[also supplied] allow the container to behung on the wall, ready to go. The insideof the container is equipped with a slide,into which an EN 148 threaded filter withits plastic cap can be inserted. The coverhas two lugs, to which Advantagebayonet-type filters can be attached,secured by a velcro strap.

[ Advantage Container]

Spare PartsPart No. Description100 32 104 1 Nosecup medium/large100 32 103 1 Nosecup small 100 32 112 2 Lens, Twin Advantage

[with Gaskets, Dual Port]100 32 113 3 Lens, Single port EN 148100 32 114 4 Lens Ring, KitD2056714 5 Inhalation Valve [20 pcs]100 32 110 6 Exhalation Valve [10 pcs] 100 32 105 7 Connector EN 148

[with O-Ring and Clip]100 32 111 8 Gasket, Dual Port [10 pcs]100 32 106 9 Connector Twin Advantage

[with O-Ring and Clip]100 32 102 10 Head Harness Advantage100 32 101 11 Button [12 pcs]100 32 107 12 Cover for Connector100 32 108 13 O-Ring for Connector [5 pcs]100 32 109 14 Spider Gasket [5 pcs]

AccessoriesPart No. DescriptionD2055765 MSA Disinfectant 90, 2 litersD2055766 MSA Disinfectant 90, 6 litersD6063705 MSA Leak Test Kit100 32 100 Carrying Strap100 17 835 Adapters Advantage

[for leak test]100 37 238 Cover lens, clear [10 pcs]100 37 237 Cover lens, tinted [10 pcs]100 37 282 Spectacles kit100 26 179 Advantage Container100 42 663 Advantage harness with silicon

straps

1 0 ]1 1

Advantage 3000Part No. Description Standards10027724 Advantage 3111, S EN 136, cl. 310027723 Advantage 3121, M EN 136, cl. 310027725 Advantage 3131, L EN 136, cl. 310042664 Advantage 3132, S EN 136, cl. 310042730 Advantage 3132, M EN 136, cl. 310042731 Advantage 3132, L EN 136, cl. 3

10027727 Advantage 3211, S EN 136, cl. 210027726 Advantage 3221, M EN 136, cl. 210027728 Advantage 3231, L EN 136, cl. 210042732 Advantage 3232, S EN 136, cl. 210042733 Advantage 3232, M EN 136, cl. 210042734 Advantage 3232, L EN 136, cl. 2S = Small, M = Medium, L = Large

Ordering Information[ Triple Safety at a Glance]

Advantage 200 LSPart No. Description Standards430357 Advantage 200 LS, S EN 140 430356 Advantage 200 LS, M EN 140430358 Advantage 200 LS, L EN 140 10015770 Paint Spray Set EN 140,

[Advantage 200 LS, 141, 143pair of A2 cartridges,pair of P2 prefilters and 2 adapters]

10016038 Pouch for Advantage 200 LS mask

S = Small, M = Medium, L = Large

Advantage FiltersPart No. Description Standards430375 P3 High efficiency EN 143

Dust Cartridge [pair]

430371 A2 Chemical EN 141Cartridge [pair]

430373 A2B2E1K1 EN 141Chemical Cartridge [pair]

430372 A2P3 EN 141CombinationCartridge [pair]

430374 A2B2E1K1P3 EN 141CombinationCartridge [pair]

10011347 P2 prefilters EN 143[10 pairs]and 2 adapters

Part No. DescriptionParticle /Mechanical filters

D1070754 Prefilter for Screw filterD1010700 Particle Filter 999

Gas FiltersD1040000 Gas Filter 87 AD1041000 Gas Filter 87 ABD1042000 Gas Filter 87 ED1045000 Gas Filter KD1040713 Gas Filter 87 ABEKD1051000 Gas Filter 87 AXD1051700 Gas Filter 87 ABEK2

Combined FiltersD1061000 Combined Filter 88 A/StD1062000 Combined Filter 88 AB/StD1061702 Combined Filter 88 ABEK/StD1061703 Combined Filter 88 ABEK2/StD1106000 Combined Filter 89 A/StD1070708 Combined Filter 89 AX/StD1070000 Combined Filter 89 AB/StD1112000 Combined Filter 89 K/StD1070705 Combined Filter 89 ABEK-Hg/StD1070707 Combined Filter 89 ABEK2-Hg/St

Special FiltersD1071000 Combined Filter 89 Hg/StD1018905 Combined Filter 89 NO-CO/StD1070701 Combined Filter 89 Reaktor/StD1070704 Combined Filter 89 Reaktor B/StD1094920 Combined Filter 580 CO/StD1018700 Comb. Filter 89 ABEK-CO-NO-Hg/St

Filters for Advantage 3100[EN 148 threaded filters]

TabTec® FiltersPart No. Description Standards10030510 A1 TabTec® EN 141

Gas Filters [pair]10030511 A2 TabTec® EN 141

Gas Filters [pair]10038476 A2B2E1K1 TabTec® EN 141

Gas Filters [pair]10030514 Adapter for

TabTec®/FLEXIfilter Combination [pair]

FLEXIfiltersPart No. Description Standards10027699 P2 FLEXIfilter EN 143

[5 pairs]10027698 P2 FLEXIfilter OR EN 143

[Odor removal][5 pairs]

10027639 P3 FLEXIfilter EN 143[5 pairs]

10027697 P3 FLEXIfilter OR EN 143[Odor removal][5 pairs]

Thank you for reading this data sheet.

For pricing or for further information, please contact us at our UK Office, using the details below.

UK OfficeKeison Products,

P.O. Box 2124, Chelmsford, Essex, CM1 3UP, England.Tel: +44 (0)330 088 0560Fax: +44 (0)1245 808399

Email: sales@keison.co.uk

Please note - Product designs and specifications are subject to change without notice. The user is responsible for determining the suitability of this product.