©2008 Delta Children’s Products, Inc. 35301-XXX_Bassinet_Instruction_V1 Made in China

Bassinet Assembly Instructions

Model Number

Manufacturer’s Code

If you have missing parts or questions...

If a part is missing or you have questions, call us. DO NOT return product parts to store from where it was purchased before calling us at:

(212) 645-9033Our service is fast, free and easier than returning the product.

Important: So we can better assist you, have the model number and manufacturer’s code available. It is located at bottom right-hand corner of this page.

Before assembly, read these instructions. Make sure all pre-assembled parts are tight. Store this instruction manual for future reference.

Adult assembly required.

Delta Children’s Products, Inc.114 West 26th Street

New York, NY 10001 (USA)

Web site: www.DeltaChildrensProducts.comE-mail: customerservice@DeltaChildrensProducts.com

Customer Service Toll-Free: (212) 645-9033

DeltaTM

Childrens’s Products

DeltaTM

Childrens’s ProductsYour Delta Baby Gear is warranted to be free from defects for a period of 30 days from the date of purchase under normal use. This warranty extends only to the original retail purchaser and is only valid when supplied with proof of purchase, or if received as a gift, when the registration is on file with Delta.

Warranty

35301-310

04 / 2011

Disassembling Bassinet for Storage

To disassemble Bassinet for storage, follow assembly steps in reverse.

Store all parts and hardware together in a safe place. Store the instruction manual for future reference.

Fabric: DO NOT USE THIS PRODUCT WITHOUT FABRIC ASSEMBLY IN PLACE. Fabric Assembly may be removed for washing. Always follow instructions for disassembly and reassembly. Fabric assembly may be hand-washed in mild detergent. Never use bleach. Air dry or use dryer on the lowest setting. Use iron for touch up on fabric for best results. Please note that the Canopy fabric cannot be removed from Canopy frame, and may be hand-washed.

Frame: Frame paint may be touched up as needed. Use only non-toxic paints approved for children’s products. Check all frame fasteners occasionally. Tighten all screws and bolts as necessary.

Cleaning and Maintenance

To install batteries: First unscrew the battery cover and install 3 C batteries as shown in the battery compartment.

To install batteries: First unscrew the battery cover and install 3 AAA batteries for Remote Controller.

SAFE BATTERY USE• Keep batteries out of the reach of children.

• Do not mix old and new batteries. • Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. • Do not mix different battery types. • Make sure batteries are inserted correctly.

• Discard leaky batteries immediately. When discarding batteries, be sure to dispose of them in the proper manner, according to your state and local regulations.

Battery Power Pack and Remote Controller

272

WARNING -BASSINET WARNINGS

Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FORFUTURE USE.

• Before each usage or assembly, inspect unit for damaged hardware, loose joints, missing parts or sharp edges. NEVER use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact Delta Children’s Product Customer Service Department at 212-645-9033 (8:00am ~ 4:30pm EST) for replacement parts, repair or instructions. DO NOT substitute parts.

• FALL HAZARD – To help prevent falls, DO NOT use this product when the infant begins to push up on hands and knees or has reached manufacturer’s recommended maximum weight of 15 lbs.

• Use bassinet with only one child at a time.

• Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as hood strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.

SUFFOCATION HAZARD: Infants can suffocate: • In gaps between an extra pad and side of the bassinet/cradle.

• On soft bedding.

NEVER add a mattress, pillow, comforter or padding. Use ONLY the pad provided by the manufacturer.

intended for that purpose. They can cause suffocation.

• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless otherwise advised by your physician.

• If a sheet is used with the pad, use only the one provided by the manufacturer or one specifically designed to fit the dimensions of the bassinet/cradle.

• The total thickness of the mattress should not exceed 1 1/2 in. and the length and width should not allow a gap greater then 1 in. between the mattress and the side of the bassinet when the mattress is pushed up against the sides and into one corner of the unit.

• DO NOT leave child unattended in the bassinet with the wheels on the bassinet frame in the “up” position.

• DO NOT place bassinet near a window where cords from blinds or drapes may strangle a child. Child may fall out of window. DO NOT place cords, straps or similar items that could become wound around a child’s neck in or near the bassinet.

• CAUTION: Check proper fit of mattress. Mattress should not be more than 1 1/2 in. thick. The maximum gap between mattress and inside of the bassinet border (or edge) should be no more than 1 in.

Failure to follow these warnings and assembly instructions could result in serious injury or death. !

WARNINGS

326NOTES WARNINGS

MOBILE WARNINGS

Read all Instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.

• A mobile is intended for visual stimulation and is not intended to be grasped by the child.

• From birth to 5 months.

• Possible entanglement injury.

• Keep out of baby’s reach.

• Remove mobile from bassinet or cradle when baby begins to push up on hands and knees. Toys are not meant to be “mouthed” by the baby and should be positioned clearly out of reach of the baby’s face and mouth.

• Adult assembly required.

• Always attach all provided fasteners (strings, straps, clamps, etc.) tightly to the bassinet according to the instructions. Check frequently. Do not add additional strings or straps to attach to the

bassinet.

• The mobile is not intended for use in playpens or portable cribs.

WARNING!

Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.

• Do not use changing table if it is damaged or broken.

• Maximum weight of child: 25 lbs. (11.34 kg).

• Never leave child unattended.

CHANGING TABLE WARNINGS

WARNING - Failure to follow these warnings and assembly instructions could result in serious injury or death. !

WARNING - ! FALL HAZARD – To prevent death or serious injury, always keep child within arm’s reach.

Notes

25FREQUENTLY ASKED QUESTIONS4

00095 - Mattress Pad (x1)

Q

Parts and Part Numbers

00084 - AccessoryBasket (x1)

A 00066 - Accessory Basket Tubes (x2)

B

00065 - Non-LockingRocker Base (x1)

C

00068 - Rocker Legs (x4)

D 02503 - Support Tube (x2)

E

00135 - Bassinet Frame (x1)

H 00131 - Mattress Support (x1)

I 01630 - Mobile Arm (x1) *Screws included

K

00083 - Bassinet Fabric Skirt (x1)

L

DO NOT REMOVE FOAM FROM BASSINET PARTS

00064 - LockingRocker Base (x1)

cc

PARTS AND PART NUMBERS

00560 - Sheet (x1)R

00073 - Canopy (x1)S

Frequently Asked Questions - continued7) Batteries

- Bassinets require 3 “C” batteries.

- If your bassinet includes a remote control, the remote control requires 3 “AAA” batteries.

8) Electronics Trouble-ShootingDouble-check that all batteries are installed correctly in the battery box. Also check that the wire is properly attached to the battery box and to the mobile base.

9) Cleaning your bassinet To clean bassinet use a damp cloth or sponge with household soap or detergent and wipe clean the vinyl, plastic, and metal parts. The sheet is machine washable and recommended to drip dry. Do not use bleach.

Battery Box

Underside of the wooden mattress support

BatteryBox

Wire

5

Parts & Hardware/Part & Hardware Numbers

HARDWARE SHOWN AT ACTUAL SIZE

00079 - Wrench00078 - Screwdriver

00077 - Rocker Leg Screw (x8)M 00139 - Mattress Support Screw (x2)

U

00130 - Lock Nuts (x4)Z

00142 - Mobile Remote Control (x1) *On certain models

X01629 - Mobile Propeller with Toys (x1) *Toys may vary *Mobile cover on certain models

T

PARTS & HARDWARE/PART & HARDWARE NUMBERS24FREQUENTLY ASKED QUESTIONS

Frequently Asked Questions

1) Warranty InformationAll Delta bassinets include a 30-day limited warranty. Please fill out the product registration card that accompanied your bassinet, and mail it back to us so we can have your information on file.

2) Model Number and Manufacturer’s CodeIt is important to have the model number and manufacturer’s code available when calling our Customer

of base assembly.

3) Height AdjustmentThe 5 positions for the height-adjustable legs are: 30.25” (lowest), 32.25” , 34.00” , 35.75” , and 37.50” (highest).

4) Weight Limits- Bassinet weight limit: 15lbs- Changing table weight limit: 25lbs

5) Mattress Pad Dimensionsare 32” x 15.75”.

6) Mattress Pad ThicknessIt is important to use only the mattress pad provided by the manufacturer. According to ASTM (American Society For Testing and Materials) standards, the total thickness of the mattress should not exceed 1.5”. The length and width should not allow a gap greater than 1” between the mattress and the side of the bassinetwhen the mattress is pushed up against the sides and into one corner of the unit. Replacement mattressesare available through Customer Service.

37.5 inches (highest position) 30.25 inches (lowest position)

00080 - Lock Nuts (x2)Y

The mattress pad dimensions

DELTA CHILDREN’S PRODUCTS114 WEST 26TH STREET. NEW YORK, NY 10001 USATEL.: 212-645-9033 STYLE NO.: MADE IN CHINA ORDER NO.:FABRIQUÉ EN CHINE

DATE OF MFG.:

35301- 310250063

04/ 2011LOT NO.: WF08006

Service department. This information can be found on a white sticker on the underside of support tube

6

Bassinet Base Assembly

1

Continue to Step 2...

Insert two (2) Accessory Basket Tubes (B) into the Non-Locking Rocker Base (cc).

00066 - Accessory Basket Tubes (x2)

B00065 - Non-Locking Rocker Base (x1)

cc

cc

B

Parts Needed:

BASSINET BASE ASSEMBLY 23MOBILE OPERATION

Mobile Operation

19

Night Light - activates the mobile light. Press to turn on mobile light for 5-minutes. To turn off sooner than 5-minutes, press again. Press the button again to start another 5 minute cycle. This operating cycle is the same for all functions except music.

Vibration - Press to start 5-minute cycle, press again to stop. The strength of vibration is adjusted with the round knob on the side of the mobile arm. This adjustment knob is also marked with waves. Turning towards the + sign increases vibration, towards the - sign reduces vibration.

Music - operates the music function . Press the button successive times to cycle the music through two modes of music, one of musical chimes, and back to off. Music volume is adjusted with the “Music Volume Adjustment” button on the other side of the mobile arm. Turning towards the + sign increases volume, towards the - sign reduces volume.

Small Lights - operates the light show. Press to start the 5-minute show. Press again to stop the music. If the music button is pressed during a light show, the show will restart, synchronized with the music.

Rotate Mobile Toys - controls the mobile. Press to begin a 5-minute cycle. Press again to stop the mobile. Press again to start a new 5-minute cycle. If the mobile button is pressed while the mobile is operating, the mobile cycle will restart, synchronized with the music.

After batteries are in place, turn on “Mobile Function” switch at base of mobile arm. This is the main power switch to the arm and also turns on the power LED on the “Night Light” button. This LED will stay lit to help you find the “Night Light” button in the dark.

Rotate Mobile Toys

Small Lights

Music

Vibration

Night LightMusic Volume

AdjustmentVibration

AdjustmentMobile Functions

On/Off

Mobile Remote requires

3 AAA batteries.

*on certain models

7

Bassinet Base Assembly - continued

2

Continue to Step 3...

00068 - Rocker Legs (x2)

D

HARDWARE SHOWN AT ACTUAL SIZE

00077 - Rocker Leg Screw (x2)

M

00078 - Screwdriver00084 - AccessoryBasket (x1)

A

AD

M

Figure 1

Parts Needed:

Insert two (2) Rocker Legs (D) into Non-Locking Rocker Base. Secure using two (2) Rocker Leg Screws (M) (see Figure 1). The screws will go through the Non-Locking Rocker Base, Rocker Legs, and into the Accessory Basket Tubes. Then slide on the Accessory Basket (A) onto the Accessory Basket Tubes.

Note: Snap button holes on Rocker Legs must face towards the inside.

BASSINET BASE ASSEMBLY22CASTER ASSEMBLY

18

Continue to Step 19...

Caster Assembly

Parts Needed:

To Lower Casters:

1 2 3

To Raise Casters:

1 23

Rotate In

Pull Down

8

Bassinet Base Assembly - continued

3

Continue to Step 4...

On other side of assembly, attach Rocker Legs (D) into Locking Rocker Base (C). Then attach Locking Rocker Base to Accessory Basket Tubes. Secure using two (2) Rocker Leg Screws (M). The screws will go through the Locking Rocker Base, Rocker Legs and into the Accessory Basket Tubes (see Figure 1).

Note: Snap button holes on Rocker Legs must face towards the inside.

00078 - ScrewdriverHARDWARE SHOWN

AT ACTUAL SIZE

D

M

00068 - Rocker Legs (x2)

D 00077 - Rocker Leg Screw (x2)

M

Figure 1

00064 - Locking Rocker Base (x1)

C

C

Parts Needed:

BASSINET BASE ASSEMBLY 21CHANGER ASSEMBLY

17

Continue to Step 18...

Changer Assembly

Parts Needed:

Place the Bassinet against a wall and lock the two (2) Locking Rocker Base caster wheels (see Figure 1). This will keep the Bassinet in a stationary position.

Figure 1

9

Bassinet Base Assembly - continued

4

Continue to Step 5...

Tie Fabric Accessory Basket (A) to the four (4) Rocker Legs (D).

A

D

Parts Needed:

BASSINET BASE ASSEMBLY20BASSINET BASKET ASSEMBLY

Bassinet Basket Assembly - continued

16

Continue to Step 17...

Parts Needed: 01629 - Mobile Assembly (x1)T

Figure 1

T

K

Attach Mobile Assembly (T) to the Mobile Arm (K) by lining up the top of the Mobile Assembly to the connector located on the Mobile Arm and push firmly up until it snaps into place (see Figure 1).

Connector

10

Bassinet Base Assembly - continued

5

Continue to Step 6...

Insert Support Tube (E) into Rocker Legs (D). Push in on the snap button. Then slide the Support Tube down until the snap button locks into place.

Note: Make sure holes on Support Tubes face in.

E

02503 - Support Tube (x1)

E

D

Parts Needed:

BASSINET BASE ASSEMBLY 19BASSINET BASKET ASSEMBLY

15

Continue to Step 16...

Parts Needed:

Bassinet Basket Assembly - continued

Insert the two ends of the Canopy (S) through the openings in the Bassinet Fabric and into the connectors on the Bassinet Basket Frame. Push down until both sides snap into place (see Figure 1). Then locate the two snaps on the Canopy (near the connectors ). Snap into place (see Figure 1). Attach the velcro or snap at the back of the Canopy to the bassinet skirt (see Figure 2 & 2a).

Figure 2

Figure 1

00073 - Canopy (x1)S

Snap

Button

Figure 2a

11

Bassinet Base Assembly - continued

6

Continue to Step 7...

IMPORTANT: Height of Support Tubes must be adjusted evenly. Do Not elevate one side higher than the other.

02503 - Support Tube (x1)

E

Note: When both Support Tubes (E) are in place, you may adjust the height by pushing in on the snap buttons and lifting up or down.

D

E

Parts Needed:

Insert Support Tube (E) into Rocker Legs (D). Push in on the snap button. Then slide the Support Tube down until the snap button locks into place.

BASSINET BASE ASSEMBLY18BASSINET BASKET ASSEMBLY

Bassinet Basket Assembly - continued

14

Continue to Step 15...

Parts Needed:

Slip the Sheet (R) over the Mattress Pad (Q). Then Assemble it into the bottom of the Bassinet Assembly (see Figure 1).

Note: On some models sheet will already be attached to mattress pad.

00095 - Mattress Pad (x1)

Q 00560 - Sheet (x1)R

Figure 1

R

Q

12

Bassinet Basket Frame Assembly

7

Continue to Step 8...

Parts Needed:

BASSINET BASKET FRAME ASSEMBLY 17BASSINET BASKET ASSEMBLY

Attach the Bassinet Frame (H) to the Bassinet Base Assembly with four (4) Rocker Leg/Basket Frame Screws (M) and four (4) Lock Nuts (Z).

00077 - Rocker Leg Screw (x4)M

00130 - Lock Nuts (x4)Z

HARDWARE SHOWN AT ACTUAL SIZE

00079 - Wrench

00078 - Screwdriver

00135 - Bassinet Frame (x1)

H

H

Z

M

Bassinet Basket Assembly - continued

13

Continue to Step 14...

Parts Needed:

Find the elastic red pockets on the bottom of both ends of Bassinet Fabric Skirt (L). Pull them underneath the wooden Mattress Support. Refasten all 10

(see Figure 1). Also you will need to fasten 4 snaps that attach skirt to Mattress Support (see Figure 2). Then loop the Mobile Arm wire and battery wire through side tabs and connect both ends together (see Figure 3).

Figure 1 Figure 2

Figure 3

Snap

Red Pocket

Mattress Support

snaps that go around the skirt

13

Bassinet Basket Frame Assembly - continued

8

Continue to Step 9...

Parts Needed:

BASSINET BASKET FRAME ASSEMBLY16BASSINET BASKET ASSEMBLY

Locate the battery compartment. With the Screwdriver, remove battery cover plate and install three (3) “C” alkaline batteries (see Figure 1). Replace the cover plate and tighten the screws.

Note: We recommend using alkaline batteries for longer battery life. Make sure batteries are correctly installed.

I

Battery Compartment

Figure 1

00131 - Mattress Support (x1)

I

Bassinet Basket Assembly - continued

12

Continue to Step 13...

Parts Needed:

Note: Unfasten 10 snaps around the Bassinet Fabric Skirt (L) (see Figure 1).

Find the opening for the Mobile Arm, and two openings for the Canopy. Make sure that they will line up. Then Slide the Bassinet Fabric Skirt (L) over the Mobile Arm and shape it around the Bassinet Basket Frame. Make sure fabric fits snugly around the top bar of the Bassinet Basket Frame.

00083 - Bassinet Fabric Skirt (x1)

L

L

Figure 1

Snap

14

Bassinet Basket Frame Assembly - continued

9

Continue to Step 10...

H

I

Attach Mattress Support (I) to Bassinet Frame (H) using four (2) Mattress Support

see Figure 1). Tighten the screws and nuts by using the Screwdriver and the Wrench. Make sure vibration battery unit is on the bottom. Note: DO NOT remove foam from around Bassinet Frame.

00079 - Wrench00078 - Screwdriver00131 - Mattress

Support (x1)

I

00139 - Mattress Support Screw (x2)

U 00080 - Lock Nuts (x2)Y

HARDWARE SHOWN AT ACTUAL SIZE

Figure 1

Parts Needed:

U

Y

BASSINET BASKET FRAME ASSEMBLY 15BASSINET BASKET ASSEMBLY

Bassinet Basket Assembly - continued

10

Continue to Step 11...

Parts Needed:01630 - Mobile Arm (x1) *screws included

K

K

00078 - Screwdriver

Remove two (2) pre-installed screws from Mobile Arm (K) (see Figure 1). Locate the pre-drilled holes on the Bassinet Frame and snap on Mobile Arm (K) (see Figure 2). Re-insert the screws into the Mobile Arm. Tighten with Screwdriver.

Figure 2

Figure 1

Screw

Screws (U) and four (2) Lock Nuts ( Y)