3cx dmg1000 setup

1

Dialogic Media Gateway Installation and Configuration Integration Note

This document is intended to detail a typical installation and configuration of the Dialogic 1000 Media Gateway Series (DMG1000) when used to interface between a PBX and the 3CX system.

2

The Fax IP Transport Mode will need to be altered based on the type of fax desired (G.711 passthrough or T.38)

7

This screenshot shows a SIP phone and the Gateway registered with 3CX. In order to get the Gateway to show as registered with 3CX, a call will need to be placed from either direction (SIP or TDM); just in case the registration timer on the Gateway is set to something high (greater than 15 seconds or so).

8

The Gateway Hostname or IP should be the IP address of the DMG1000. The port number should be the standard 5060 (should match the port number used on the Gateway as seen later). Set the registration setting to Nothing so authentication is not required by 3CX for the Gateway when the Gateway comes online with 3CX.

9

The Source Identification section can either be set to Match Any Fields, or Match All Fields (shown here) with the values as set above. The Custom Value is set to the IP address and port number of the DMG1000 (if Match All Fields is selected). For the Outbound Parameters section all defaults are taken.

10

All defaults taken for the inbound and outbound parameters. If fax is desired, un-check the PBX Delivers Audio checkbox under the Other Options section.

12

The password entered here for the extension should match the password entered for the SIP phone when SIP phone configuration is performed.

14

The IP address of the Gateway will be entered in the Provisioning section, under the Select Interface drop-down.

15

The Gateway will be added as a PSTN.

16

Set the inbound and outbound routes to be the extension, not the voicemail box.

17

For Authentication of the TDM phone, just mimic the extension. Under the Other Options section, both the Internal Number and Outbound Caller ID should be set to a dummy number (10000 in this case). This number is for internal routing within 3CX only, and does not have to match any PBX dial plan.

19

Under the Apply these rules, section, the Prefix should be set to either the digit that is used to access the TDM side (in this case, 3), or 0-9 or 0,1,2,3,4,5,6,7,8,9 for allowing all TDM calls to route. Under the Make Outbound Calls on section, select the Gateway name configured previously in the Route 1 drop-down and set the Strip Digits to 0.

20

Set the port number to be the same port number configured within the DMG1000 (seen above).

30

Initial Issue: Cannot get the Gateway to register with 3CX

Corrective Action: Disable the registration from with the Gateway (VoIP | General) Uncheck the registration setting from within 3CX (Lines | Manage |

Gateway/Provider | Registration Settings) Second Issue:

Cannot register PingTel or sipxphone Corrective Action:

Some SIP phones will not authenticate during registration, so dont use those phones (using x lite as the soft SIP phone)

Third Issue:

Can place calls from SIP phone ([email protected]) to TDM ([email protected]), but not TDM to the SIP phone

Corrective Action: Needed to re-configure the gateway setup in 3CX.

31

Copyright Notice and Legal Disclaimer Copyright 2008 Dialogic Corporation. All Rights Reserved. You may not reproduce this document in whole or in part without permission in writing from Dialogic Corporation at the address provided below. All contents of this document are furnished for informational use only and are subject to change without notice and do not represent a commitment on the part of Dialogic Corporation or its subsidiaries (Dialogic). Reasonable effort is made to ensure the accuracy of the information contained in the document. However, Dialogic does not warrant the accuracy of this information and cannot accept responsibility for errors, inaccuracies or omissions that may be contained in this document. INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH DIALOGIC PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED AGREEMENT BETWEEN YOU AND DIALOGIC, DIALOGIC ASSUMES NO LIABILITY WHATSOEVER, AND DIALOGIC DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT OF A THIRD PARTY. Dialogic products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility applications. Due to differing national regulations and approval requirements, certain Dialogic products may be suitable for use only in specific countries, and thus may not function properly in other countries. You are responsible for ensuring that your use of such products occurs only in the countries where such use is suitable. For information on specific products, contact Dialogic Corporation at the address indicated below or on the web at www.dialogic.com. It is possible that the use or implementation of any one of the concepts, applications, or ideas described in this document, in marketing collateral produced by or on web pages maintained by Dialogic may infringe one or more patents or other intellectual property rights owned by third parties. Dialogic does not provide any intellectual property licenses with the sale of Dialogic products other than a license to use such product in accordance with intellectual property owned or validly licensed by Dialogic and no such licenses are provided except pursuant to a signed agreement with Dialogic. More detailed information about such intellectual property is available from Dialogics legal department at 9800 Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada H4M 2V9. Dialogic encourages all users of its products to procure all necessary intellectual property licenses required to implement any concepts or applications and does not condone or encourage any intellectual property infringement and disclaims any responsibility related thereto. These intellectual property licenses may differ from country to country and it is the responsibility of those who develop the concepts or applications to be aware of and comply with different national license requirements. Dialogic, Dialogic Pro, Brooktrout, Cantata, SnowShore, Eicon, Eicon Networks, Eiconcard, Diva, SIPcontrol, Diva ISDN, TruFax, Realblocs, Realcomm 100, NetAccess, Instant ISDN, TRXStream, Exnet, Exnet Connect, EXS, ExchangePlus VSE, Switchkit, N20, Powering The Service-Ready Network, Vantage, Making Innovation Thrive, Connecting People to Information, Connecting to Growth and Shiva, among others as well as related logos, are either registered trademarks or trademarks of Dialogic. Dialogic's trademarks may be used publicly only with permission from Dialogic. Such permission may only be granted by Dialogics legal department at 9800 Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada H4M 2V9. Any authorized use of Dialogic's trademarks will be subject to full respect of the trademark guidelines published by Dialogic from time to time and any use of Dialogics trademarks requires proper acknowledgement. The names of actual companies and products mentioned herein are the trademarks of their respective owners. This document discusses one or more open source products, systems and/or releases. Dialogic is not responsible for your decision to use open source in connection with Dialogic products (including without limitation those referred to herein), nor is Dialogic responsible for any present or future effects such usage might have, including without limitation effects on your products, your business, or your intellectual property rights. 05-2667-001 11/08

/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 150 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages false /GrayImageDownsampleType /Bicubic /GrayImageResolution 150 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 300 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile (None) /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName (http://www.color.org) /PDFXTrapped /False

/SyntheticBoldness 1.000000 /Description >>> setdistillerparams> setpagedevice

3cx dmg1000 setup

Documents