4400 mobile phone tester series - digimes · as s page 3 12/06/07 440x mobile phone tester series...
TRANSCRIPT
-
4400 Mobile Phone Tester Series
-
General overview
-
ass
page 312/06/07
440x Mobile Phone Tester Series
The Willtek 440x Mobile Phone Tester series is …
A state-of-the-art productA multi-standard platform
• GSM, HSCSD, GPRS, EDGE, • cdma2000 1xRTT, IS-95, AMPS • WCDMA/UMTS• TD-SCDMA (Non-Call Mode)• 1xEV-DO (coming)
Provides many useful options, • MS Power Supply, MS Current Measurement• Audio Analyzer / Codec• Parallel Multi Phone Tests
Comes in two different versions • 4403 and 4405
-
ass
page 412/06/07
4403 & 4405
4403The Willtek 4403 is the basic unit for applications requiring higher speed and good accuracy (Gen: 0.9 dB, typical 0.4 dB, Analyzer: 0.8 dB)The Willtek 4403 is aimed for service and small scale production
4405The Willtek 4405 is the advanced unit for higher speed and very high accuracy (Gen. 0.7 dB, typical 0.3 dB, Analyzer 0.37 dB, typical 0.15 dB)The Willtek 4405 is aimed at production, hardware engineering and QA
Design
Board alignment and calibration
FunctionalTest
FunctionalCheck
QualityCheck
High-Level Repair
Align & Test
Repair Loop
Service, e.g. 4403Manufacturing, e.g. 4405R&D, e.g. 4405
-
ass
page 512/06/07
Current front and rear panel
Power SupplyRF and Measurement
Industrial PCFloppy drive
Keypad
RF out
Audio In/Out
-
ass
page 612/06/07
New PC for 4400 – Speed enhancement!
“Old” PC (current solution)• VGA• Keyboard (PS2)• Mouse (RS232)• Parallel Printer Port• RS-232• GPIB• TCP/IP requires
PCMCIA cards (option)• 2 – PCMCIA Slots
NEW PCVGA, Parallel Printer Port, RS-232Keyboard and Mouse (via PS2 or USB)GPIB and TCP/IP (standard)2 – USB (Host, type A)1 – USB (Device, type B)
-
System Options
-
Non-Call Mode
-
ass
page 912/06/07
To align and calibrate a mobile phoneFor all major standards included
Test setup • Example, different from manufacturer to manufacturer
4400 acts as a signal generator and spectrum analyzer• Generates specific signals (different from manufacturer to manufacturer) and displays the results • Under remote control by a service software
Non-Call Mode option(s) in the 440x
Power supply
Willtek 440x
Various Test-Jigs
PC with Service
Software
GPIB connectionN – SMA connection
RS232 connection
-
ass
page 1012/06/07
4400 approvals for alignment and calibration for GSM / GPRS / EDGE and WCDMA
Mobile phone manufacturer GSM / GPRS / EDGE WCDMA/UMTS Remarks
Nokia SW Version 4.24
Sony Ericsson SW Version 4.21 V6.00.SERP001
LGSW Version 4.24(for GSM/GPRS)
Under evaluation Target: end of July
SiemensSW Version 4.24(for GSM/GPRS)
No Siemens product so far
MotorolaSW Version 4.24(for GSM/GPRS)
( ) SW Version V6.10 Implementation isrunning
VK Cooperation
SW Version 4.24 (only GSM)
No product so far
SAGEM No complete product so far Use an EMP solution(tuning with SERP)
SW Version V6.10
-
Call Mode
-
ass
page 1212/06/07
4460 GSM System Option
Call ProcessingLocation updatingMobile originated call, mobile terminated callHandover (intra-cell, cross-band)Call clearing by MS or BSSMS, mobile originated/terminatedMS Info screen
Transmitter TestingPower level and power time templatePhase error, frequency errorModulation spectrum, ACPM
Receiver TestingBER
-
ass
page 1312/06/07
4482 Parallel Multiple Phone Test Option4940 Bi-directional RF Port (4-Ports) Option
Decreases the setting timeSimultaneously supports up to four mobile phonesContinuous test sequence – Allows to perform test on a phone while the other phone is been configured
-
ass
page 1412/06/07
4461 Multislot - HSCSD Option
Call ProcessingLocation updatingMobile originated call, mobile terminated callHandover (intra-cell, cross-band)Call clearing by MS or BSMS Info screen
Transmitter TestingPower level and power time templatePhase error, frequency errorModulation spectrum, ACPM
Receiver TestingBER (max. on 2 uplink/downlink)
OtherSupports up to 4 uplink/downlink slots in asynchronous mode
-
ass
page 1512/06/07
4462/4463 GPRS System Option
GPRS Synchronous ModeGPRS call processing, including
GPRS Attach (registration)GPRS Test Mode CommandPacket transfer (“Uplink TBF”, “Downlink TBF”)
Integrates with GSM call mode GUIMultislot TX measurementsBLER, BER measurements
GPRS: General Packet Radio ServiceTBF: Temporary Block flowBER: Bit Error RateBLER: BLock Error Rate
-
ass
page 1612/06/07
4468 EDGE System Option
Call ProcessingAttach/Detach ProceduresUplink TBF establishmentETSI Test Mode A
Transmitter TestingModulation Quality – Frequency error, RMS EVM, Peak EVM, 95th Percentile, Origin Offset, I/Q ImbalancePower - Peak power, power versus time
-
ass
page 1712/06/07
4464 CDMA2000 1xRTT Option
Call Processingregistrationmobile originated call, mobile terminated callHandover (intra-cell, cross-band)call clearing by MS or BS
Transmitter TestingModulation Quality – rho, frequency error, time error, code domain power, code domain phase, code domain timing measurementsPower - Min/Max, Gated, Open Loop, Standby, Closed Loop, and Access Probe power measurements
Receiver TestingSensitivity and Dynamic range using FER measurements
-
ass
page 1812/06/07
4467 WCDMA Call Mode Option
Call ProcessingRegistrationMobile originated call, mobile terminated callCall clearing by MS or BS
Transmitter TestingMin/Max powerInner Loop Power ControlOpen Loop Power ControlSpectrum (OBW, ACLR, SEM)Modulation Quality (EVM, frequency error, magnitude error, phase error, I/Q offset, I/Q imbalance, Rho)Constellation DisplayCode Domain Measurements (PCDE, Code Spectrum)
Receiver TestingBER / BLER Measurements
OtherUE Info with UE Measurement Report
-
ass
page 1912/06/07
Add-on: Registration
After a successful synchronization between Node B and UE and the network provider is the right one the registration procedure is initialized
RRC Connection request (CCCH)RRC Connection setup (CCCH)
RRC Connection setup complete (DCCH)Location Updating request (DCCH)
Authentication RequestAuthentication ResponseSecurity mode commandSecurity mode complete
Location Updating AcceptTMSI reallocation complete
RRC connection ReleaseRRC connection Release Complete
Node B
UE
-
ass
page 2012/06/07
Add-on: Call SetupMobile originated call
After a successful registration a mobile originated call is possible …
Phase 1
Phase 2
Phase 3
RRC Connection request (CCCH)RRC Connection setup (CCCH)
RRC Connection setup complete (DCCH)CM Service Request (DCCH)
Authentication RequestAuthentication ResponseSecurity mode commandSecurity mode complete
SetupCall proceeding
Radio bearer setupRadio bearer setup complete
AlertingConnect
Connect Acknowledge
Node B
UE
-
ass
page 2112/06/07
… or a mobile terminated call
Add-on: Call SetupMobile terminated call
Paging (PCCH)RRC Connection request (CCCH)RRC Connection setup (CCCH)
RRC Connection setup complete (DCCH)Paging response (DCCH)Authentication Request
Authentication ResponseSecurity mode commandSecurity mode complete
SetupCall confirmed
Radio bearer setupRadio bearer setup complete
AlertingConnect
Connect Acknowledge
Node B
UE
-
ass
page 2212/06/07
4484 Tracer option for 4400 WCDMA System option
All these messages (registration, mobile originated/terminated call) are displayed in the text/status field
For a detailed look you can use the 4484 Tracer option for the 4400 WCDMA system option
Running on a PCConfiguration via GPIB or TCP/IPConnection is realized via TCP/IP connectionYou can configure which message should be displayed
-
ass
page 2312/06/07
RAPID!
4400
Controller
RAPID!Program
4400SoftwareSoftware
START
RESULTS
RAPID! = Run Application Programs with Integrated DevelopmentSelf-contained automatic test programEasy integration
-
General options
-
ass
page 2512/06/07
4473 MS Power Supply Option
The MS Power Supply option replaces battery of the equipment under testSupply voltage: 0-10 VSupply current up to 4 Apeak
-
ass
page 2612/06/07
4474 Current Measurement Option
Graphical representation of current drawn by MSDuration one GSM TDMA slotUp to 4 A, 10 VRequires 4473 Power Supply OptionThe TCH and power level can be changed within the optionThe current range can be set to: 400mA, 1A, 2A and 4A
-
ass
page 2712/06/07
4478 TCP/IP Option
The TCP/IP option enables networking capabilities for the Willtek 4400Fixed or DHCP connection typeFeatures that are available with the option
SW update via network driveRemote control via TCP/IP connection (using individual ports for different Willtek 4400s)Storing of files from the RAPID! program on any serverAccess to the Willtek 4400 from any PC
-
ass
page 2812/06/07
4470 Audio Option
Audio Option comprises a full AF Analyzer / GeneratorFeatures are:
Linear/Logarithmic displayTemplate checkEntry of customer specific templatesAveragingFrequency span variable (4/20kHz)Wave File Replay (Multi-tones)
-
440x Mobile Phone Tester Series
http://www.willtek.com
440x Mobile Phone Tester Series4403 & 4405Current front and rear panelNew PC for 4400 – Speed enhancement!Non-Call Mode option(s) in the 440x4400 approvals for alignment and calibration for �GSM / GPRS / EDGE and WCDMA4460 GSM System Option4482 Parallel Multiple Phone Test Option�4940 Bi-directional RF Port (4-Ports) Option4461 Multislot - HSCSD Option4462/4463 GPRS System Option4468 EDGE System Option4464 CDMA2000 1xRTT Option4467 WCDMA Call Mode Option�Add-on: Registration�Add-on: Call Setup�Mobile originated callAdd-on: Call Setup�Mobile terminated call4484 Tracer option for 4400 WCDMA System optionRAPID!4473 MS Power Supply Option4474 Current Measurement Option4478 TCP/IP Option4470 Audio Option