5995406146 frigidaire laundry center with tumble action washers service manual
DESCRIPTION
5995406146 Frigidaire Laundry Center with Tumble Action Washers Service ManualTRANSCRIPT
-
11111111
White-Westinghouse
ELECTROLUX HOME PRODUCTS NORTH AMERICA
SERVICE MANUAL
Laundry Center
With
Tumble Action Washers
5995406146 May 2004
-
2ATTENTION!!!This service manual is intended for use by persons having electrical and mechnicaltraining and a level of knowledge of these subjects generally considered acceptable in theappliance repair trade. Electrolux Home Products cannot be responsible, nor assume anyliability, for injury or damage of any kind arising from the use of this manual.
2001 White Consolidated Industries
SAFE SERVICING PRACTICES - ALL APPLIANCES
To avoid personal injury and/or property damage, it is important that Safe ServicingPractices be observed. The following are some limited examples of safe practices:
1. DO NOT attempt a product repair if you have any doubts as to your ability tocomplete it in a safe and satisfactory manner.
2. Before servicing or moving an appliance: Remove the power cord from the electrical outlet, trip the circuit breaker to the
OFF position, or remove the fuse. Turn off the gas supply. Turn off the water supply.
3. Never interfere with the proper operation of any safety device.
4. USE ONLY REPLACEMENT PARTS CATALOGED FOR THIS APPLIANCE.SUBSTITUTIONS MAY DEFEAT COMPLIANCE WITH SAFETYSTANDARDS SET FOR HOME APPLIANCES.
5. GROUNDING: The standard color coding for safety ground wires is GREEN, orGREEN with YELLOW STRIPES. Ground leads are not to be used as currentcarrying conductors. It is EXTREMELY important that the service technicianreestablish all safety grounds prior to completion of service. Failure to do so willcreate a hazard.
6. Prior to returning the product to service, ensure that: All electrical connections are correct and secure All electrical leads are properly dressed and secured away from sharp edges,
high-temperature components, and moving parts All non-insulated electrical terminals, connectors, heaters, etc. are adequately
spaced away from all metal parts and panels All safety grounds (both internal and external) are correctly and securely
connected All panels are properly and securely reassembled
-
3SAFE SERVICING PRACTICES 2QUICK REFERENCE SHEET 9
Serial nameplate location 9Serial number breakdown 9Tech sheet location 9Washer section 10
Component resistance chart 10Water fill height 10Electrical requirements (Gas laundry center) 10Electrical requirements (Electric laundry center) 10Incoming water pressure 10Drain requirements 10Motor 10Operation speeds 11Tub pulley to motor pulley ratio 11Tub capacity 11
Dryer section specification 12Electrical 12Drum 12Airflow CFM 12Drum temperatures 12Dimension 12Vent capability 12Component resistances 12
Drive motor 12Timer motor 12Heating element 12Bias heater on thermostat 12Burner assembly 12
Sample wiring diagram for dryer section gas models 13Sample wiring diagram for dryer section electric models 14Dryer cycle chart 15Sample wiring diagram for washer section 16Washer timer chart 17
SECTION A - INSTALLATION INSTRUCTIONS 18What to do if you smell gas 18Pre-installation requirements 18
Tools required for installation 18Electrical requirements (Electric laundry center) 18
Circuit 18Power supply 18Power supply cord kit 18Outlet receptacle 18
Electrical requirements (Gas laundry center) 18Circuit 18Power supply 19Power supply cord 19Outlet receptacle 19
Water supply requirements 19Drain requirements 19Exhaust system requirements 19Gas supply requirements 21Location of your laundry center 21
Do not install your laundry center 21Installation in recess or closet 21
Moble home installation 22Unpacking 22
-
4Rough-in dimensions 23Electrical installation 24
Grounding requirements 24Electrical connections for A 3-wire system 25Electrical connections for A 4-wire system 25
Installation 26Replacement parts 27
SECTION B - DRYER OPERATING INSTRUCTIONS 28Before operating your dryer 28Operating steps 28Cycle selection 28
Automatic dry cycle 28Air fluff cycle 29Timed dry cycle 29
Energy saving tips 29SECTION C - WASHER OPERATING INSTRUCTIONS 30
Before operating your washer 30Operating steps 30Cycle selection 30
Whites/regular cycle 30Short wash cycle 31Colors/perm press cycle 31Knits and delicates cycle 31
Controls 31Temperatures 31Cycle signal 31Extra rinse 31Final spin 31
SECTION D - OWNER GUIDE 32For your safety 32Product registration 32Important safety instructions 32
Prevent fire 32Gas laundry centers 33
For your safety 33Protect children 33Prevent injury 33
Washing procedures 34Sort laundry 35Prepare items for washing 35Pretreat stains 35Add detergent, bleach and fabric softener 36Set cycle selector knob and washer controls 37Start the washer 37Remove items when the cycle is completed 38General precautions 38
Stain removal 38Safe stain removal procedures 38For successful stain removal 39Stain removal 39
Common washing problems 40Drying procedures 41
Prepare items for drying 41Check that lint screen is clean and in place 41Load the dryer 41Close the dryer door and set dryer controls 42Turn cycle selector clockwise to the desired setting 42
-
5Start the dryer 42When the cycle ends, remove items immediately 42
Features 42Cycle signal control (some models) 42Drum light (some models) 42Drying rack (some models) 42
Common drying problems 43Care and cleaning 44
Cleaning the dispenser drawer area 44Inside 44Inside the dryer 45Outside 45
Winterizing instructions 46Avoid service checklist 46Sample warranty 50
SECTION E - DRYER SECTION OPERATION 51Airflow electric dryers 51Airflow gas dryers 52Airflow problems 52
Restrictions 53Air leaks 53Short unrestricted vents 53
Electrical operation (electric dryer) 53Automatic dry cycle 54
Drive motor circuit 54The timer motor circuit 54
Automatic press saver option 55The heating circuit 55The cycle signal circuit 55
Timed dry cycle 55The timer motor circuit 55Drive motor and heating circuits 56
Air fluff cycle 56The timer motor circuit 56Drive motor circuit 56The heating circuit 56
Electrical operation (gas dryer) 56Automatic dry cycle 56
Drive motor circuit 56The timer motor circuit 57
Automatic press saver option 57The heating circuit 57The cycle signal circuit 59
Timed dry cycle 59The timer motor circuit 59Drive motor and heating circuits 59
Air fluff cycle 59The timer motor circuit 59Drive motor circuit 59The heating circuit 59
SECTION F - WASHER SECTION OPERATION 60Timer 60Line switch 60Dispenser drawer reed switch 60Door switch assembly 61Pressure switch 62Automatic dispenser 62
-
6Temperature switch 64Water inlet valve 64
Valve operation 65Extra rinse switch 66
SECTION G - TROUBLESHOOTING FLOW CHARTS 68Dryer section index 68Washer section index 69Electric dryer completely inoperative 70Gas dryer completely inoperative 71Electric and gas dryers; timer advances in timed dry but not in auto dry 72Electric and gas dryers; timer does not pause in autodry with wet clothes in the dryer 72Electric and gas dryers blower motor runs but drum does not turn 73Electric and gas dryers longer than normal drying times 73Electric dryers blower motor runs but dryer does not heat 74Gas dryers blower motor runs but dryer does not heat 75Electric dryers blower motor runs but timer does notadvance in auto or timed dry 76Electric and gas dryers dryer over heating 76Electric and gas dryers timer advances in auto dry but not in timed dry 76Speed control and motor plug and pin layout 77Washer completely inoperative 78Timer does not advance 78Washer does not drain 79Extra rinse setting does not work 79Bleach dispenser does not operate 80Softner dispenser does not operate 80Drive motor does not turn 81Drive motor spins but does not tumble 82Drive motor tumbles but does not spin 82Drive motor tumbles very slowly in any timer position 83Spin cycle operating at incorrect speed for switch setting 83Water fill does not turn off 84Incorrect water level 84Slow water fill 85Door indicator lamp does not glow 85Washer will not fill in any setting of the temp switch 86Water temperature is too hot or too cold in the washcycle with the temp switch set to warm/warm 87Washer will only fill with hot water in the wash cycle, with the tempswitch set to warm/cold but does fill with cold in the rinse cycle 87
SECTION H - TEARDOWN 88Removing the knobs 88
All knobs except the washer timer knob 88Removing timer bezel 88Removing the access panel 88Opening the console 89Removing the dryer timer 89Removing the dryer buzzer 89Removing the console end caps 90Removing the console front panel 90Removing the start switch 90Removing the temperatures switch 91Removing the automatic press saver switch 91Removing the water temperature switch 91Removing the extra rinse switch 91
-
7The door lock lamp assembly 92Removing the door lock lamp assembly 92Removing the washer buzzer 92Removing the final spin speed switch 92Removing the washer timer 93Removing the electronic moisture sensor control 93Removing the dryer door 93Separating the dryer door panel 93Removing the dryer door seal 94Removing the dryer door heat shield 94Removing the dryer door handle 94Removing the dryer door strike 95Removing the dryer door hinge 95Removing the dryer door switch 95Removing the heat shield 95Removing the dryer front panel 95Replacing the felt seals 96Replacing the front duct 96Removing the door catch 96Replacing the foam seal 96Removing the dryer section rear access panel 97Releasing the dryer belt 97Removing the idler pulley 97Removing the idler pulley assembly 97Removing the belt 98Removing the control thermostat and thermostat heater 98Removing the sensor (Gas dryers) 98Removing combustion chamber shield (Gas dryers) 98Removing the burner (Gas dryers) 99Removing the ignitor (Gas dryers) 99Removing the gas valve coils (Gas dryers) 99Removing the burner and combustion chamber assembly,manual shut off and the internal gas pipe (Gas dryers) 99Removing manual shut off and internal gas pipe (Gas dryers) 100Removing pressure regulator valve assembly (Gas dryers) 100Removing the combustion chamber (Gas dryers) 100Removing the dryer top panel 100Removing the vane from the dryer drum 101Removing the dryer drum 101Removing the ball hitch from the drum 101Removing the teflon glides 101Removing the drum heat shield (Electric dryers) 101Removing the hitch 102Removing the high limit thermostat 102Removing the thermal limiter (Electric dryers) 102Removing the heating element assembly (Electric dryers) 102Removing the duct and heat shield (Gas dryers) 103Removing the blower and motor assembly 103Disassembling the blower and motor assembly 104Removing the internal vent duct 105Removing the motor and blower assembly base 105Removing the burner assembly base (Gas dryers) 106Removing the dryer section side panels 106Removing the dryer section 107Removing the detergent drawer 108Detergent drawer disassembly 108Removing the washer section top panel 109
-
8Removing the top panel spacers 109Removing the washer section upper front panel 109Removing the reed switch 110Removing the front service panel 110To remove loading door and hinge 111Disassembling the door 111To remove door strike 112Removing the door safety switch 112Removing the bellows (door boot) 113Reinstalling or replacing the boot 114Removing the water inlet duct 117Removing the detergent dispenser solenoid assembly 117Removing the detergent cavity assembly 117Removing the pressure switch 118Removing the suspension springs 118Removing the water inlet valve 119Removing the drain pump assembly 119Disassembling the drain pump 120To remove the air bell 120Removing the back service panel 121Removing the speed control board assembly 121Drive belt 122To remove or replace the drive belt 122Removing the drive motor 122Removing the large pulley 122Removing the rear counter weight 122Removing the air shock absorber 123Removing the outer tub 123Removing the spin basket and rear tub half 123Removing the front counter weights 124Removing the spin basket vanes 124Removing the spacers between the dryer section and the washer section 124Removing the mounting brackets 125
-
9QUICK REFERENCE SHEET
1. Serial nameplate location: on the innerpanel of the dryer section door.
2. Serial number breakdown.
3. Tech sheet location
Behind the access panel.
X E 4 1 2 0 4 2 4 7
Incremented unit numberProduction week
Last digit of production yearProduct identification
Manufacturing Facility
-
10
Component resistance chart.
Water fill height 2.03 0.80 No load,start position of heavy wash
and 2.53 0.53 No load at the startposition of all other cycles.
Electrical requirements. (Gas laundry center)
Electrical requirements. (Electric laundry center)
Incoming water pressure.
Drain requirements.
Drive motor.
Circuit - Individual, properly polarized and grounded 15amp. branch circuit fused with 15 amp. time delay fuseor circuit breaker.
30 and 120 pounds per square inch (maximumunbalance pressure, hot vs. cold, 10 psi.)
Drain capable of eliminating 17 gals (64.3 L) per minute.
A standpipe diameter of 1-1/4 in. (3.18 cm) minimum.
The standpipe height above the floor should be:
Minimum height: 24 in. (61 cm)
Maximum height: 96 in. (244 cm)
Resistance Electrical component @ 77 F (25C) Water valve solenoids 880 10% Door lock solenoid 1325 75 Ohms Timer motor 2425 6% Pump motor 15 7% Dispenser valve soleniods 1100 7%
M1 TO M2 2.6 7%M2 TO M3 2.6 7%M1 TO M3 2.6 7%M5 TO M6 184 7%
Motor
Agitate wattage - Max 200
Spin wattage - Max 475
Circuit - Individual 30 amp branch circuit fused with 30amp minimum time delay fuses or circuit breakers.
QUICK REFERENCE SHEET (Washer Section)
-
11
Operation speeds: (Washer Section)Agitate Speed - RPM (Regular/Perm Press) 51 4Agitate Speed - RPM (Knits/Delicates/Hand Washables) 35 4
Spin speeds
Regular Cycle
Spin Speed R.P.M. (Normal) 900 39Spin Speed R.P.M. (Fast) 950 39
Perm Press Cycle
Spin Speed R.P.M. (Normal) 650 39Spin Speed R.P.M. (Fast) 900 39
Knits/Delicates/Hand Washables Cycle
Spin Speed R.P.M. (Normal) 450 25Spin Speed R.P.M. (Fast) 650 30
Tub Pulley to Motor Pulley Ratio 16 TO 1Tub Capacity 2.65 cu. ft.
-
12
QUICK REFERENCE SHEETDRYER SECTION
SPECIFICATION
ElectricalVolts 120/208 or 120/240Amps (circuit)Motor wattageHeat input (Watts @ 240VAC)Heat input (BTU/Hr.)Auto. Elec. Ignition
DrumSize (Cu. Ft.)FinishR.P.M.
Airflow CFM
Drum temperatures (Max.opening on 1st cycle)HighMediumLow
Dimension (Inches)HeightWidthDepth
Vent capability
Component resistances*
Drive motor (120 volt, 60 Hz, 1/4 h.p. 1725 rpm) Motor Start Winding Motor Run Winding
Timer motor
Heating element
Bias heater on thermostat
Burner assembly Ignitor Secondary Coil Booster Coil
* +/- 10% @ 77 F
ELECTRIC MODELS
120/208 or 120/24030
160-350 Watts3200/4500
--
5.7Stainless steel
48 - 54
180
155 - 225150 - 210145 - 205
75 1/427
30 13/16
4-Way
GAS MODELS
12015
160-350 Watts-
20,000Yes
5.7Stainless steel
48 - 54
180
150 - 220140 - 215135 - 195
75 1/427
30 13/16
4-Way
Electric Models
4.5 Ohms3.8 Ohms
2280-2300 Ohms
12.8 Ohms
7,200 Ohms
-
-
-
Gas Models
4.5 Ohms3.8 Ohms
2280-2300 Ohms
2,000 Ohms
50 - 400 Ohms1200 Ohms1320 Ohms
-
13
SAMPLE WIRING DIAGRAM FOR DRYER SECTION GAS MODELS
NOTE:DASHED LINES INDICATECIRCUITS THAT ARE NOTIN ALL MODELS
FABRIC SELECTOR SWITCH - GAS MODELSPOSITION
1234
FUNCTIONHIGH
MEDIUMMEDIUM/LOW
LOW
RESISTANCEOPEN CIRCUIT
3K+/- 5%1.5K+/- 5%10 MAX
NOTES - GAS MODELS
1 - ALL WIRING MUST CONFORM TO LOCAL ELECTRICAL CODE.
2 - CONNECT DRYER TO 15 AMP INDIVIDUAL BRANCH CIRCUIT.
3 - DRYER TIMER SHOWN IN THE OFF POSITION DOOR SWITCH CLOSED, MOTOR AT REST, THERMOSTAT CLOSED, AND FABRIC SELECTOR SWITCH AT HIGH HEAT.
WIRING CODES
QUICK DISCONNECT TERMINAL
SCREW TERMINALCONNECTION
NO CONNECTION
MOTOR SWITCH
SPLICE
MOTOR PROTECTORCHASSIS (CABINET) GROUND
HARNESS CONNECTOR TERMINAL
INSULATED TERMINAL
120 VACL1
TO NEUTRALCONNECTOR
WHT
WHT
WHT
WHT
WHT
WHT WHT WHT
WHT
N
GROUND
CABINETRED/BLKTO L1 CONNECTOR
BLK
BLK
DRUMLIGHT
C
NC NO GRAY
GRAY
STARTSWITCH
DOORSWITCH
M1M6
M4
M5 M2
SIGNAL
C
S
TM
XH
B
BRN
TIMERMOTOR
OPTIONSWITCH
TESTLEAD
MOTOR
TAN
TAN
DRYER TIMER
FABRIC SELECTOR
TAN
TAN
AORG
CONTROLTHERMOSTAT
ELECTRIC MOISTURESENSORCONTROL
GRN
CABINETBASE
START
RUN
YEL
CONTACTSENSOR
BRN P1
P2
P3
P4
P5
RED
RED
GAS CONTROL VALVE2
HOLDING COIL
SECONDARYCOIL
BOOSTER COIL
113
3
BLK ORG
ORG
ORG
IGNITERSENSOR
HIGH LIMITTHERMOSTAT
PURP
THIS HARNESS WIRENOT FUNCTIONALBLUE5
4
1.5 K
1.5 KTHERMOSTAT HEATER 2 K
G
-
14
240 VAC
120 VAC 120 VAC
NL2TO NEUTRALCONNECTOR
WHTWHT
WHT WHT
WHT
WIRE NOT INCLUDED IN MODELS PROVIDED WITH 4 - WIRE POWER CORD GRN
CABINET
TO L1CONNECTOR
RED/BLK
RED
RED
RED
RED
RED
L1
BLKBLK
DRUMLIGHT
SIGNAL
CNC
NODOORSWITCH
GRAY GRAY
GRAY
STARTSWITCH
S
B
H
C
TM
PURP
BRN BRN
BRN
OPTIONSWITCH
TIMERMOTOR
X
THERMALLIMITER
TESTLEADS P3
TAN
TAN
TANMOTOR
M6 M2
M4
M5 M1
P1
CABINET BASE
GRN
A ORG
WHT
TAN
P5
CONTROLTHERMOSTAT
START
RUN
P2P4
HIGH LIMITTHERMOSTAT
ORG/BLK
CONTACT SENSOR
BLK
DRYER TIMER
1 3PURP
HEATER4500 W4
THIS HARNESS WIRENOT FUNCTIONALON THIS MODEL
5 BLUEFABRIC SELECTOR SWITCH
750750
THERMOSTATHEATER, 7.2 K
ELECTRONICMOISTURE SENSOR CONTROL
SAMPLE WIRING DIAGRAM FOR DRYER SECTION ELECTRIC MODELS
NOTE:DASHED LINES INDICATECIRCUITS THAT ARE NOTIN ALL MODELS
FABRIC SELECTOR SWITCH - ELEC MODELSPOSITION
1234
FUNCTIONHIGH
MEDIUMMEDIUM/LOW
LOW
RESISTANCE ( 4-5 )OPEN CIRCUIT
1.5K +/-5%750 +/-5%10 MAX
NOTES - ELEC MODELS
1 - ALL WIRING MUST CONFORM TO LOCAL ELECTRICAL CODE.
2 - CONNECT LUNDRY CENTER TO 30 AMP INDIVIDUAL BRANCH CIRCUIT.
3 - DRYER TIMER SHOWN IN THE OFF POSITION DOOR SWITCH CLOSED, MOTOR AT REST, THERMOSTAT CLOSED, AND FABRIC SELECTOR SWITCH AT HIGH HEAT.
WIRING CODES
QUICK DISCONNECT TERMINAL
SCREW TERMINALCONNECTION
NO CONNECTION
MOTOR SWITCH
SPLICE
MOTOR PROTECTORCHASSIS (CABINET) GROUND
HARNESS CONNECTOR TERMINAL
INSULATED TERMINAL
-
15
1. THE BAR CHART ABOVE REPRESENTS ONE COMPLETE REVOLUTION OF THE TIMER SHAFT.
2. SHADE PORTION OF THE BAR CHART INDICATES THE PROPORTIONAL TIMES THAT THE INTERNALTIMER CONTACTS ARE CLOSED.
3. SIGNAL:
A CIRCUIT X - H WILL CLOSE FOR 5 SEC +/- 3 SEC 1 TO 2 TIMES IN THIS AREA. WHEN 2CLOSURES OCCUR THEY WILL BE 5 MIN APART.
B CIRCUIT X - H WILL CLOSE FOR 5 SEC +/- 3 SEC 5 TO 7 TIMES IN THIS AREA.CLOSURES WILL BE 5 MIN APART.
OFF
OFF
OFF
AUTO DRY58.75 MIN
TIMED DRY 90 MIN
AIR FLUFF 22.5 MIN
AAA
CAM1
1B23
4B
CIRCUITB-A HEATERB-S MOTORB-C MOTOR
X-H SINGAL
GAS & ELECTRIC DRYER CYCLE CHARTEXCARE15 MIN
X-TM TIMER MOTOR
-
16
TOP PANEL CABINET L1 DRYERCONNECTOR
BLK/WHT BLK
14
YEL/RED
DISPENSER DRAWER REED SWITCH
#2 1 2 #6
DOORSWITCH
BLU/WHT 4.4 2.1
DOOR LOCK COILEXTRA RINSE SWITCH
1
1 2
2
#8
PINK
PINK
2.2
4.3
STATUS LIGHT
#3 WHT
#5PUMP MOTOR
M
WAX MOTOR
AQUAPRESSURE SWITCHYEL/BLK
TAN
4
2
TAN/BLK
3
2
ORG/WHT SOFTENER
WHTDISPENSER VALVES
WHT/RED
BLEACH
1 #4BLK/RED
#7
#1
WHT
WHT
WHT
CYCLE SIGNAL
GRAY
12
10
8
BROWN
RED/YEL
ORG
BLUE
BLUE
2
3
5
TEMP SWITCH4
1
YEL
HOT
WATER VALVES
COLD
N DRYERCONNECTOR
TACHOGENERATOR
6
1
1
3
2
2T
YEL/WHT
TAN/WHT
ORG/BLK
RED/BLK
C6.5C6.6
C10.2(A)
C10.1(B)
C10.4(T1)
C6.1(P1)
C6.2(P2)C10.6(C)
C10.10(D)
C6.3(P3)C10.9(E)
BLUE
PINK/BLK
WHT/RED
BROWN
RED
TIMERMOTOR
1
3
5
7
6
WASHER TIMER
REDPURPLE
YEL/BLK
SPEED SWITCH
C10.8(F)
C10.59TM)
C10.3(T2)
C6.4
SPEED CONTROL UNIT
YEL
GREEN
5MOTOR MOTOR
FRAME
4
PTC
TIMER LINE SWITCH
SAMPLE WIRING DIAGRAM WASHER SECTION
WASHER TIMER SHOWN IN OFF POSITIONDISPENSER DRAWER OPEN, & DOOR OPEN
SPEED SWITCHSPEED 1 - 2
NORMAL CLOSEDFAST OPEN
TEMPERATURE SWITCH CIRCUITWASH/RINSEHOT/COLDWARM/COLDCOLD/COLDWARM/WARM (OPT)
1 - 3 1 - 5 2 - 4
X=CONTACTS CLOSED
XX
X
XXXX
-
17
WIR
ING
CO
DE
S
CO
NN
EC
TIO
NN
O C
ON
NE
CTI
ON
MO
TOR
SW
ITC
HS
PLI
CE
MO
TOR
PR
OTE
CTO
R
CH
AS
SIS
(CA
BIN
ET)
GR
OU
ND
HA
RN
ES
S C
ON
NE
CTO
R T
ER
MIN
AL
WH
ITE
SID
EB
LAC
K S
IDE
1 3 5 7 9 11 13 15
C A M
P O S I T I O N S7
11
91215182124
TT
CC
BB
DD
232 5
6
TM TM
971 10
1514
1817
16 1920
21
2224
11
0 2 4 6 8 10 12 14
TER
MIN
AL
POSI
TIO
N C
HA
RT
(EN
D V
IEW
)
D
ASH
ED L
INES
IND
ICAT
E
INTE
RN
AL
TIM
ER B
USS
ING
T
TO
P TE
RM
INA
L C
CA
M T
ERM
INA
L B
BO
TTO
M T
ERM
INA
L
*
DEN
OTE
S B
USS
ED C
IRC
UIT
S
AC
CO
MPL
ISH
ED T
HR
OU
GH
T
HE
WIR
ING
HA
RN
ESS.
WA
SHER
TIM
ER C
HA
RT
OFF
OFF
OFF
OFF
FIN
AL
SPIN
FIN
AL
SPIN
WASH
WASH
WA
SHW
ASH
KN
ITS/
DEL
ICAT
ES C
YCLE
EXTR
A C
AR
E
FIN
AL
SPIN
FIN
AL
SPIN
SHO
RT
WA
SHR
EGU
LAR
WA
SH
HEAVY
MED
LIGHT
CIR
CU
IT
DET
ENT
MA
CH
INE
POW
ER
CO
DE
A
SOLE
NO
ID 2
CO
DE
BC
OD
E E
SOLE
NO
ID 1
CO
DE
CTM
DIR
ECT
CO
DE
DW
ASH
WAT
ER
MA
IN
RIN
SE W
ATER
MA
IN
WA
SH L
AM
PR
INSE
WAT
ER
TEM
PW
AS
H W
ATER
TE
MP
RIN
SE L
AM
PFI
NA
L SP
IN L
AM
P
PRES
S S
W. B
YPA
SS
BU
ZZER
DR
AIN
PU
MP
EX R
.
DR
AIN
PU
MP
STEP
TIM
E (M
IN)
STEP
NO
C O N T A C T TTTTTTTTTTTTTTT BBBBBBBBBBBBBBB
TER
M. F I X E D
A C T I V E
C A M 0/0 0
21
122 22
23 23 23 2323
24 24
24
56
6323
19 21
45
5
7 7
7
9 916 1618 18
11
11
10 10
10
12
12
13 15
814
14
17
17
15
9
2019
19
21
3.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
1
6.7
6.0
6.0
1.0
1.0
1.0
1.0
1.0
1.0
5
3.0
3.0
3.0
3.0
2.5
10
8.12
8.12
2.6
2.6
1520
25
6.7
6.0
30
3.0
3.0
3.0
3.0
3.0
3.0
3.0
35
7.2
2.6
4550
40
10.0
1.0
1.0
2.0
2.0
5.1
2.6
-
18
3. Carpenters level4. Flat or straight blade screwdriver5. Duct tape6. Rigid or flexible metal 4 inch (10.16 cm) duct7. Vent hood8. Pipe thread sealer (Gas)9. 1/4 inch socket w/ratchet10. 3/8 inch socket w/ratchet11. 3/8 inch open end wrench12. 7/16 inch open end wrench13. 9/16 inch open end wrench
ELECTRICAL REQUIREMENTS
ELECTRIC Laundry Center
Circuit- Individual 30 amp branch circuit fused with 30amp minimum time delay fuses or circuit breakers.
POWER SUPPLY - 3-wire or 4-wire, 240 volt, singlephase, 60 Hz, Alternating Current.
POWER SUPPLY CORD KIT- The laundry center MUSTemploy a 3-condutor power supply cord NEMA 10-30type SRDT rated at 240 volt AC minimum, 30 amp, with3 open end spade lug connectors with upturned ends orclosed loop connector OR a 4-condutor power supplycord NEMA 14-30 type SRDT or ST (as required) ratedat 240 volt AC minimum, 30 amp, with 4 open end spadelug connectors with upturned ends or closed loop con-nectors and marked for use with clothes dryers. If beinginstalled in a manufactured (mobile) home, the laundrycenter MUST employ a 4-condutor power supply cordNEMA 14- 30 type SRDT or ST (as required) rated at240 volt AC minimum, 30 amp, with 4 open end spadelug connectors with upturned ends or closed loop con-nectors and marked for use with clothes dryers. SeeELECTRICAL CONNECTIONS. (Canada -4- wire powersupply cord is installed on laundry center.)
OUTLET RECEPTACLE - NEMA 10-30R (3-wire) recep-tacle or NEMA 14- 30R (4-wire) receptacle to be locatedso the power supply cord is accessible when the laun-dry center is in an installed position.
GAS Laundry Center
CIRCUIT -Individual 15 amp branch circuit fused with a15 amp maximum time delay fuse or circuit breaker.
Section A - Installation InstructionsTumble Action Laundry Center
Gas & Electric
Before beginning installation, carefully read theseinstructions. This will simplify the installation andensure the laundry center is installed correctly andsafely. Leave these instructions near the laundry cen-ter after installation for future reference.
NOTE: The electrical service to the laundry centermust conform with local codes and ordinances andthe latest edition of the National Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian Electrical Code,CSA C22.1
NOTE: The gas service to the laundry center mustconform with local codes and ordinances and thelatest edition of the National Fuel Gas Code ANSIZ223.1/NFPA 54, or in Canada, the Canadian NaturalGas and Propane Installation Code, CSA B149.1.
NOTE: The laundry center is designed under ANSIZ21.5.1 or ANSI/UL 2158- CAN/CSA C22.2 (latestedition) for HOME USE only. This laundry center isnot recommended for commercial applicationssuch as restaurants or beauty salons, etc.
For your safety the information in thismanual must be followed to minimize the risk of fire orexplosion or to prevent property damage,personalinjury or loss of life.
- Do not store or use gasoline or other flammablevapors and liquid in the vicinity of this or any otherappliance.
- WHAT TO DO IF YOU SMELL GASDo not try to light any appliance.Do not touch any electrical switch; do not useany phone in your building.Clear the room, building or area of all occupants.Immediately call your gas supplier from aneighbors phone. Follow the gas suppliersinstructions.If you cannot reach your gas supplier, call the firedepartment.
Installation and service must be preformed by aqualified installer, service agency or the gas supplier.
PRE-INSTALLATION REQUIREMENTS
Tools and Materials Required for Installation:
1. Phillips head screwdriver2. Channel-Iock adjustable pliers
-
19
POWER SUPPLY -3 wire, 120 volt single phase, 60 Hz,Alternating Current.
POWER SUPPLY CORD -The gas laundry center isequipped with a 120 volt 3-wire power cord.
OUTLET RECEPTACLE - Properly grounded 3-prongreceptacle to be located so the power supply cord isaccessible when the washer is in an installed position.NOTE: GFI (Ground Fault Interrupter) receptacle is notrequired or recommended.
Note: Do not underany circumstancesremove groundingprong from plug.
Grounding Prong
WATER SUPPLY REQUIREMENTS
Hot and cold water faucets MUST be installed within42 inches (106.68 cm) of your laundry centers waterinlet. The faucets MUST be 3/4 inch (1.9 cm) gardenhose type so inlet hoses can be connected. Waterpressure MUST be between 10 and 120 pounds persquare inch (maximum unbalance pressure, hot vs.cold, 10 psi). Your water department can advise you ofyour water pressure. The hot water temperature shouldbe about 140 degrees F.
DRAIN REQUIREMENTS
1. Drain capable of eliminating 17 gallons per minute.
2. A standpipe diameter of 1 inches (3.18 cm) minimum.
3. The standpipe height above the floor should be:Minimum height: 24 inches (61 cm)Maximum height: 96 inches (244 cm)
NOTE: For installations requiring a longer drain hose,have a qualified technician install a longer hose, PartNumber 134042901, available from an authorized partsdistributor. For drain systems in the floor, install asiphon break kit, available from your local hardwarestore .
EXHAUST SYSTEM REQUIREMENTS
Use only 4 inch (10.16 cm) diameter (minimum) rigid orflexible metal duct and approved vent hood which has aswing-out damper(s) that opens when the dryer is inoperation. When the dryer stops, the damper(s)automatically closes to prevent drafts and the entranceof insects and rodents. To avoid restricting the outlet,maintain a minimum of 12 inches (38.5 cm) clearancebetween the vent hood and the ground or any other ob-struction.
The following are specific require-ments for proper and safe operation of your laundrycenter. Failure to follow these instructions can cre-ate excessive drying times and fire hazards.
Do not use plastic flexible duct to exhaustthe dryer. Excessive lint can build up inside the exhaustsystem and create a fire hazard and restrict air flow.Restricted air flow will increase drying times. If yourpresent system is made up of plastic duct or metal foilduct, replace it with a rigid or flexible metal duct. En-sure the present duct is free of any lint prior to in-stalling the laundrycenter dryer duct.
If the dryer is not exhausted outdoors,some fine lint will be expelled into the laundry area.An accumulation of lint in any area of the home can
-
20
create a health and fire hazard. The dryer exhaustsystem MUSTbe exhausted to the outside of thedwelling!
Do not allow combustible materials (forexample: clothing,draperies/curtains, paper) to come incontact with the exhaust system. The dryer MUST NOTbe exhausted into a chimney, a wall, a ceiling, or anyconcealed space of a building which can accumulatelint, resulting in a fire hazard.
Do not exceed the length of duct pipe ornumber of elbows allowed in the EXHAUST DUCTLENGTHS chart. Lint can accumulate in the system,plugging the system and creating a fire hazard, as wellas increasing drying times.
Do not screen the exhaust ends of the ventsystem, nor use any screws or rivets to assemble theexhaust system. Lint can become caught in the screen,on the screws or rivets, clogging the exhaust systemand creating a fire hazard as well as increasing dryingtimes. Use an approved vent hood to terminate the ductoutdoors, and seal all joints with duct tape. All maleduct pipe fittings MUST be installed downstream withthe flow of air.
Explosion hazard. Do not install thelaundry center where gasoline or other flammables arekeptor stored. If the laundry center is installed in a ga-rage, it must be a minimum of 18 inches (45.7 cm) abovethe floor. Failure to do so can result in death, explosion,fire or burns.The exhaust system back pressure MUST not exceed0.6 inches (1.52 cm) of water column measured withan inclined manometer at the point the exhaustconnects to the dryer.
The exhaust system should be inspected and cleaneda minimum of every two years with normal usage. Themore the dryer is used, the more often you shouldcheck the exhaust system and vent hood for properoperation.
The maximum length of the exhaust system dependsupon the type of duct used, number of elbows and typeof exhaust hood.
The maximum length for both rigid and flexible duct isshown in the chart below.
The laundry center may be exhausted four (4) ways withrear flush installation:
1. Straight back
2. Down (8 inch [20.32 cm] length of 4 inch [10.16 cm]rigid duct and 1 elbow down)
3. Left (8 inch [20.32 cm] length of 4 inch [10.16 cm]rigid duct, 1 elbow down and 1 elbow left)
4. Right (8 inch [20.32 cm] length of 4 inch [10.16 cm]rigid duct, 1 elbow down and 1 elbow right)
To exhaust up, add an 11 inch (27.94 cm) length ofstandard 4 inch (10.16 cm) diameter duct and a 90elbow. The unit will be positioned about 4 inches (11.43cm) away from the wall (flush to wall exhausting may bedone by going below the dryer then sideways).
-
21
An exhaust hood positioned to line up with the dryerexhaust can be installed directly through the outsidewall. To exhaust to the side or down, add an 8 inch(20.32 cm) length of standard 4 inch (10.16 cm)diameter duct and a 90 elbow.
GAS SUPPLY REQUIREMENTS
1. Installation MUST conform with local codes, or inthe absence of local codes, with the National FuelGas Code, ANSI Z223.1 (latest edition) or in Canada,the current AN/CGA B149.
2. The gas supply line should be of 1/2 inch (1.27 cm)pipe.
3. If codes allow, flexible metal tubing may be used toconnect your dryer to the gas supply line. The tubingMUST be constructed of stainless steel or plastic-coated brass.
4. The gas supply line MUST have an individual shutoffvalve.
5. A 1/8 inch (0.32 cm) N. P. T. plugged tapping,accessible for test gage connection, MUST beinstalled immediately upstream of the gas supplyconnection to the dryer.
6. The dryer and its individual shutoff valve MUST bedisconnected from the gas supply piping systemduring any pressure testing of the gas supply pipingsystem at test pressures equal to or less than 1/2psig (3.45 kPa).
7. The dryer MUST be isolated from the gas supplypiping system by closing its individual manual shutoffvalve during any pressure testing of the gas supplypiping system at test pressures equal to or less than1/2 psig (3.45 kPa).
LOCATION OF YOUR LAUNDRY CENTER
DO NOT INSTALL YOUR LAUNDRY CENTER:
1. In an area exposed to dripping water or outsideweather conditions.
2. In an area where it will come in contact with curtainsor drapes.
3. On carpet. Floor MUST be solid with a maximumslope of 1 inch (2.54 cm).
4. On a pedestal. Excessive vibration can occur
INSTALLATION IN RECESS OR CLOSET
1. A laundry center installed in a bedroom, bathroom,recess or closet, MUST be exhausted outdoors.
2. No other fuel burning appliance shall be installed inthe same closet as the Gas laundry center.
3. Your laundry center needs the space around it forproper ventilation.
DO NOT INSTALL YOUR LAUNDRY CENTER IN ACLOSET WITH A SOLID DOOR.
4. A minimum of 120 square inches (774.2 squarecm) of opening, equally divided at the top andbottom of the door, is required. Air openings arerequired to be unobstructed when a door isinstalled. A louvered door with equivalent airopenings for the full length of the door isacceptable.
-
22
5. The following illustrations show minimum clearancedimensions and air openings for proper operation ina recess or closet installation.
MOBILE HOME INSTALLATION
1. Dryer MUST be exhausted outside (outdoors, notbeneath the mobile home) using metal ducting thatwill not support combustion. Metal ducting must be4 inches (10.16 cm) in diameter with noobstructions. Rigid metal duct is preferred.
2. If dryer is exhausted through the floor and areabeneath the mobile home is enclosed, the exhaustsystem MUST terminate outside the enclosure withthe termination securely fastened to the mobile homestructure.
3. Refer to EXHAUST SYSTEM REQUIREMENTS forother important venting requirements.
4. When installing a gas dryer into a mobile home, aprovision must be made for outside make up air. Thisprovision is to be not less than twice the area of thedryer exhaust outlet.
5. Installation MUST conform to current ManufacturedHome Construction & Safety Standard (which is aFederal Regulation Title 24 CFR-Part 32-80) or whensuch standard is not applicable, with AmericanNational Standard for Mobile Homes. In Canada, theCSA Z240is applicable.
The laundry center is designed underANSI Z 21.5.1 for HOME USE HOME USE HOME USEHOME USE HOME USE only.
UNPACKING
1. Using the four shipping carton corner posts (two oneach side), carefully lay the laundry center on its leftside and remove the foam shipping base.
NOTE: Because of the weight of the appliance, twopeople may be required.
2. Return laundry center to an upright position.
3. Remove the following from the back side of thewasher:
4 bolts,4 yellow plastic spacers,3 metal P clamps.
4. Remove the service panel from the front of the washer.
5. Remove the 4 nuts and 6 large washers that attachthe 2 yellow shipping braces to the drum and the base.Lift up on the drum and remove the braces (a yellowribbon surrounds the items to be removed).
0 IN.(0 CM.)
0 IN.(0 CM.)
0 IN.(0 CM.)
DRYER
WASHER
1 IN.(2.54 CM.)
60 SQ. IN.(387.1 SQ.CM.)
60 SQ. IN.(387.1 SQ.CM.)
-
23
3 IN.(9.52 CM.)
DRAIN OUTLET (REAR)
27 in.(68.58cm.)
WATER INLETS (REAR)
ELECTRICALCONNECTION
40 IN.(102.87 CM.)
42 IN.(107.32 CM.)
75 IN.(191.14 CM.
53 IN.(134.62 CM.)
44 IN.(111.76 CM.)
30 IN.(80.65 CM.)
12 IN.(31.75 CM.)
VENT
GAS SUPPLYPIPE (REAR) 9 3/8 IN.
(23.81 CM.)
5 IN.(13.33 CM.)
17 IN.(44.45 CM.)
29 IN.(75.57 CM.)
3 IN.(7.62 CM.)
3 1/8 IN.(7.94 CM.)
1 7/8 IN.(4.76 CM.)
47
16 IN.(41.27 CM.)
36 IN.(91.44 CM.)
ROUGH-IN DIMENSION
6. Remove the large styrofoam block located under thedrum. Lift up on the drum, tilt the base of the foamblock inwards toward the rear of the washer until free,then pull it out.
7. Remove and discard the yellow ribbon and label fromthe front of the washer.
8. Replace the service panel and screws.
9. Carefully move the laundry center to within 4 feet(1.22m) of the final location to begin the installation.
NOTE: If the laundry center is to be transported at alater date, the shipping support hardware must bereinstalled to prevent shipping damage.
-
24
ELECTRICAL INSTALLATIONALL ELECTRIC Laundry Centers
The following are specific require-ments for proper and safe electrical installation ofyour laundry center. Failure to follow these instruc-tions can create an electrical shock and/or a firehazard.
This appliance MUST be properly grounded.Electrical shock can result if the laundry center is not prop-erly grounded. Follow the instructions in this manual forproper grounding.
Do not use an extension cord with thislaundry center. Some extension cords are not designed towithstand the amounts of electrical current this laundry cen-ter utilizes and can melt, creating electrical shock and/or firehazard. Locate the laundry center within reach of the recep-tacle for the length power cord to be purchased, allowingsome slack in the cord. Refer to the pre-installation require-ments in this manual for the proper power cord to be pur-chased.
A U.L. approved strain relief must beinstalled onto power cord. If the strain relief is not attached,the cord can be pulled out of the laundry center and can becut by any movement of the cord, resulting in electrical shock.
Do not use an aluminum wired receptaclewith a copper Wired power cord and plug (or vice versa). Achemical reaction occurs between copper and aluminumand can cause electrical shorts. The proper wiring andreceptacle is a copper wired power cord with a copperwired receptacle OR aluminum wired power cord with analuminum wired receptacle.
NOTE: Laundry centers operating on a 208 volt power sup-ply will have longer drying times than laundry centers oper-ating on a 240 volt power supply.
GROUNDING REQUIREMENTSNon-Canadian ELECTRIC Laundry Center
Improper connection of the equipment
grounding conductor can result in a risk of electrical shock.Check with a licensed electrician if you are in doubt as towhether the appliance is properly grounded.
For a grounded, cord-connected laundry center:
1. The laundry center MUST be grounded. In the event ofmalfunction or breakdown, grounding will reduce the riskof electrical shock by a path of least resistance forelectrical current.
2. If your laundry center is equipped with a power supplycord having an equipment-grounding conductor and a
grounding plug, the plug MUST be plugged into anappropriate, copperwired receptacle that is properlyinstalled and grounded in accordance with all local codesand ordinances. If in doubt, call a licensed electrician.
For a permanently connected laundry center:
The laundry center MUST be connected to a grounded metal,permanent wiring system; or an equipment grounding con-ductor MUST be run with the circuit conductors and con-nected to the equipment-grounding terminal or lead on theappliance.
Canadian ELECTRIC Laundry Center
Improper connection of the equipment
grounding conductor can result in a risk of electrical shock.Check with a licensed electrician if you are in doubt as towhether the appliance is properly grounded.
For a grounded cord connected laundry center:
1. The laundry center MUST be grounded. In the event ofmalfunction or breakdown, grounding will reduce therisk of electrical shock by providing a path of leastresistance for the electrical current.
2. Since your laundry center is equipped with a powersupply cord having an equipment-grounding conductorand a grounding plug, the plug MUST be plugged intoan appropriate outlet that is properly installed andgrounded in accordance with all codes and ordinances.If in doubt, call a licensed
ELECTRICAL CONNECTIONSFOR A 4-WIRE SYSTEM
WARNINGWARNING
1. Remove the screw securing the terminal block accesscover to the rear panel and remove cover.
2. Install a U.L. approved strain relief connector in the entryhole on the back panel.
GREEN GROUNDSCREW
GREENCONDUCTOR SILVER TERMINAL
BLACK
WHITE
RED
GREENGROUND WIRE
TERMINAL BLOCK
-
25
3. Insert a NEMA 14-30 Type ST or SRDT, U.L. approvedpower cord through the strain relief.
4. Attach the green power cord ground wire to the cabinetwith the green ground screw.
5. Attach the white (neutral) wire from the power cord to thesilver-colored center terminal on the terminal block.Tighten the screw securely.
6. Attach the red and black wires from the power cord to theouter brass-colored terminals on the terminal block.Tighten both screws securely.
7. Tighten the screws securing the cord restraint firmlyagainst the power cord.
8. Reinstall the terminal block access cover.WARNINGALL GAS Laundry Centers
1. The laundry center, when installed, MUST be electricallygrounded in accordance with local codes, or in theabsence of local codes, with the National ElectricalCodes, ANSI/NFPA (latest edition) or in Canada, CSAC22.1 CanadianElectrical Code Part 1.
2. The laundry center is equipped with a three-prong(grounding) plug for your protection against shockhazard and should be plugged directly into aproperly grounded three-prong receptacle. Do notcut or remove the grounding prong from the plug.
ELECTRICAL CONNECTIONS FOR A3-WIRE SYSTEM
NON-CANADIAN ELECTRIC Laundry Center
1. Remove the screw securing the terminal blockaccess cover to the rear panel and remove cover.
2. Install a U.L. approved strainrelief connector in the entryhole on the back panel.
3. Insert a NEMA 10-30Type SRDT, U.L. approvedpower cord through the strain relief.
4. Attach the power cord neutral (central wire)conductor to the silver colored center terminal onthe terminal block. Tighten the screw securely.
5. Attach the remaining two power cord outerconductors to the outer brass colored terminals onthe terminal block.Tighten both screw securely.
6. Tighten the screws securing the cord restraint againstthe power cord.
7. Reinstall the terminal access cover.
ELECTRICAL CONNECTIONSFOR A 4-WIRE SYSTEM
NON-CANADIAN ELECTRIC Laundry Center
1. Remove the screw securing the terminal blockaccess cover to the rear panel and remove cover.
2. Install a U.L. approvedstrain relief connectorin the entry hole on theback panel.
-
26
3. Remove the green neutral ground wire from the greenground screw located above the termial block.
4. Insert a NEMA 14-30 Type ST or SRDT, U.L. approvedpower cord through the strain relief.
5. Attach the green power cord ground wire to thecabinet with the green ground screw.
6. Attach the white (neutral) wire from the power cordand the green ground wire from the applianceharness to the silver-colored center terminal on theterminal block. Tighten the screw securely.
7. Attach the red and black wires from the power cordto the outer brass-colored terminals on the terminalblock. Tighten both screws securely.
8. Tighten the screws securing the cord restraint firmlyagainst the power cord.
9. Reinstall the terminal block access cover.
INSTALLATION
1. Run some water from the hot and cold faucets toflush the water lines and remove particles that mightclog up the water valve screens.
2. Check inlet hoses to ensure the rubber washers areinstalled in each end.
3. Carefully connect the inlet hoses to the water valve(on the left side of the washer cabinet), tighten byhand, then tighten another 2/3 turn with pliers.
DO NOT CROSS THREAD OR
OVERTIGHTEN THESE CONNECTIONS.
4. Determine which water faucet is the HOT waterfaucet and carefully connect the bottom inlet hose tothe HOT water faucet, tighten by hand, then tightenanother 2/3 turn with pliers. Carefully connect the topinlet hose to the COLD water faucet, tighten by hand,then tighten another 2/3 turn with pliers.
DO NOT CROSS THREAD OR
OVERTIGHTEN THESE CONNECTIONS. Turn the water on and check for leaks at
both connections.
5. Carefully move the laundry center to its final location.Rollers on the rear of the washer base allow for easymovement in closet or alcove installations. Gentlypush back on the washer cabinet. NOTE: Gently
pushing the dryer cabinet may lift the front of thewasher over 1/8 which will engage the rear legs tothe floor.
6. With the washer in its final position, place a level ontop of the washer, no rocking of the washer shouldexist. Adjust the front leveling legs up or down toensure the washer is resting solid. Rear legadjustment is accessible through the front servicepanel. Turn the lock nuts on each leg up towards thebase of the washer and snug with a wrench.
NOTE: Leg extension should not be over one (1) inch to prevent excessive vibration.
7. GAS CONNECTION (Gas laundry centers only)
a. Remove the shipping cap from gas pipe at the rear ofthe dryer.NOTE: DO NOT connect the laundry center to L.P.gas service without converting the gas valve. An L.P.conversion kit must be installed by a qualified gastechnician.
b. Connect a 1/2 inch (1.27 cm) I.D. semi-rigid orapproved pipe from the gas supply line to the 3/8inch (0.96 cm) pipe located on the back of the dryer.Use a 1/2 inch (1.27 cm) to 3/8 inch (0.96 cm)reducer for the connection. Apply an approved threadsealer that is resistant to the corrosive action ofliquefied gases on all pipe connections.
c. Open the shutoff valve in the gas supply line.
d. Test all connections by brushing on a soapy watersolution. NEVER TEST FOR GAS LEAKS WITHAN OPEN FLAME.
8. Form a U shape on the end of the drain hose withthe hose pointed toward the drain. Place the formedend in a laundry tub or a standpipe and secure with acable tie provided in the enclosure package. An airgap must be around the drain hose. WATER WILLSIPHON FROM THE WASHER IF THE ABOVEINSTRUCTIONS ARE NOT FOLLOWED.
-
27
9. Remove the two (2) screws securing the dryer frontaccess panel to the dryer cabinet. Lift the panel untilthe tabs can be disengaged from the cabinet. Remove the panel and set aside.
WARNING
10.Connect the exhaust duct to outside duct work. Useduct tape to seal all joints.
11.Plug the power cord into a grounded outlet.NOTE: Check to ensure the power is off at a circuitbreaker/fuse box before plugging the power cord intoan outlet.
12.Turn on the power at a circuit breaker/fuse box.
Before operating the dryer, make
sure the dryer area is clear and free fromcombustible materials, gasoline, and otherflammable vapors. Also see that nothing (suchas boxes, clothing, etc.) obstructs the flow ofcombustion and ventilation air.
13.Reinstall the dryer front access panel.
14. Run the washer and dryer though a cycle. Check forproper operation.
Note: On gas dryers, before the burner willlight, it is necessary for the gas line to bebled of air. If the burner does not lightwithin 45 seconds the first time the dryeris turned on, the safety switch will shut theburner off. If this happens, turn the timerto OFF and wait 5 minutes beforemaking another attempt to light.
15.If your laundry center does not operate, pleasereview the Avoid Service Checklist located in yourOwners Guide before calling for service
.16. Place these instructions in a location near the
laundry center for future reference.
NOTE: A wiring diagram is located behind the dryerfront access panel.
REPLACEMENT PARTS
If replacement parts are needed for your laundry center,contact the source where you purchased your laundrycenter.
Destroy the carton, plastic bags, andmetal band after the laundry center is unpacked. Chil-dren might use them for play. Cartons covered with rugs,bedspreads, or plastic sheets can become airtight cham-bers causing suffocation. Place all materials in a gar-bage container or make materials inaccessible to chil-dren.
Label all wires prior to disconnection when
servicing controls. Wiring errors can cause improper anddangerous operation. Verify proper operation after ser-vicing.
The instructions in this manual andall other literature included with this laundry center arenot meant to cover every possible condition and situa-tion that may occur. Good safe practice and cautionMUST be applied when installing, operating and main-taining any appliance.
Maximum benefits and enjoyment are achievedwhen all the Safety and Operating instructionsare understood and practiced as a routine withyour laundry tasks.
WARNING
AccessPanelScrews
-
28
Section B - Dryer Operating InstructionTumble Action Laundry CenterGas & Electric
Before Operating Your Dryer
Read your Owners Guide. It has important safetyand warranty information. It also has many sugges-tions for best drying results.
To reduce the risk of fire, electricshock, or injury to persons, read the IMPORTANTSAFETY INSTRUCTIONS in your owners guide beforeoperating this appliance.
Operating Steps
Read Drying Procedures in your Owners Guide. Itexplains these operating steps in detail.
1. Prepare items for drying.
2. Check that lint screen is clean and in place.
3. Load the dryer. If desired, add a dryer fabric softener sheet.
4. Close the dryer door.
5. Set Drying Temperatures control.
6. Turn cycle selector clockwise to desired setting.
7. Start dryer. Turn the Turn to Start control clockwise to ON. Hold for 1-2 seconds and
release.
8. A signal will sound when the cycle ends.
9. Remove items immediately and hang or fold.
10. Clean lint screen after every load.
Temperature Selection
Always follow directions on fabric care labels.
To avoid fire hazard, do not use heatto dry items containing feathers or down, foam rubber,plastics, or similarly textured, rubber-like materials.Use Air Fluff cycle only.
The REGULAR/WHITES-HIGH HEAT, PERMPRESS/COLORS-MEDIUM HEAT, andKNITS-MEDIUM LOW HEAT and DELICATES-LOWHEAT temperature settings may be used with any cyclesetting.
Cycle Selection
Turn cycle selector clockwise to desired cycle andsetting.
Each cycle ends with a cool down period. The heatautomatically turns off and the load continues totumble for 5-10 minutes. This reduces wrinkling andmakes items easier to handle during unloading. Dryingtime varies depending on size and dampness of load,weight and fabric type. Room temperature and humid-ity, type of installation and electrical voltage or gaspressure can also affect drying time.
Automatic Dry Cycle
TOWELS - This setting is best for towel loads.
-
29
Select the REGULAR/WHITESHIGH HEATtemperature setting.
NORMAL - This setting is best for cotton items.Select the REGULAR/WHITESHIGH HEATtemperature setting.
DELICATES/PERM PRESS - This setting is best fordelicate, knit, or perm press items. Select thePERM PRESS/COLORSMEDIUM HEATtemperature setting for permanent press items, theKNITS-MEDIUM-LOW temperature setting for most knititems, or the DELICATESLOW HEAT temperaturesetting for delicate items.
Occasionally a load may seem too damp oroverdried at the end of the cycle. To increase dryingtime for similar loads in the future, set the cycleselector on the indicator line to the left of theTOWELS, NORMAL, or DELICATES/PERM PRESSsetting. For loads requiring less drying time, set thecycle selector on the indicator line to the right.
DAMP DRY - This setting is best for items you wishto partially dry before hanging or ironing. Select thetemperature setting most suitable for the load.
Press Saver - If the dried load cannot beremoved promptly at the end of the cycle, thecycle selector will automatically automaticallyautomatically automatically automaticallyadvance to the Press Saver setting if the PressSaver Press Saver Press Saver Press SaverPress Saver option is turned ON . Unheatedtumbling continues for up to 24 minutes to helpreduce wrinkling. The timer will not will not willnot will not will not automatically advance intothe Press Saver setting if the Press Saver PressSaver Press Saver Press Saver Press Saveroption is turned OFF.
Note: Press Saver Note: Press Saver Note: PressSaver Note: Press Saver Note: Press Saver canbe used independently for up to 15 minutes ofunheated tumbling to help remove wrinklesfrom items that are already dry. Turn selectorknob to Press Saver and start dryer. It is notnecessary to set Temperatures or Press Saveroption controls.
Air Fluff Cycle
This cycle provides up to 20 minutes of tumbling withoutheat. Use AIR FLUFF to dry items containing feathers ordown, foam rubber, plastics, or similarly textured,
rubber-like materials, to freshen clothing, pillows orblankets, or to dust draperies.
Timed Dry Cycle
This cycle provides approximately 80 minutes of dryingtime at the temperature selection of your choice.
Energy Saving Tips
Keep the lint screen clean and exhaust the dryercorrectly.
Sort laundry properly and select proper temperatureand cycle settings. Choose an automatic dry cyclewhenever possible for accurate drying time.
Dry only full loads. Single items and smallloads usually take longer to dry.
Avoid overloading, adding wet items to a partially dryload, and overdrying.
Dry one load after another to take advantage of a warmdryer.
Opening the door needlessly causes warm air toescape, which prolongs drying time.
If possible, use the dryer on low humidity days.
Install the dryer in an area where the roomtemperature is at least 45F (7C).
-
30
Section C - Washer Operating InstructionTumble Action Laundry Center
Before Operating Your Washer
Read your washer Use and Care Guide. It hasimportant safety and warranty information. It also hasmany suggestions for best washing results.
To reduce the risk of fire, electricshock, or injury to persons, read the IMPORTANTSAFETY INSTRUCTIONS in your washer Use andCare Guide before operating this appliance.
Operating Steps
Read and follow Washing Procedures in your Useand Care Guide. It provides detailed information forpreparing the wash load and choosing control settingsto ensure best washing results.
1. Sort laundry into loads that can be washedtogether.
2. Prepare items for washing.
3. Pretreat stains and heavy soil.
4. Add laundry load to the wash drum.
5. Open the dispenser drawer and add themeasured amount of detergent to thedetergent compartment. If desired, add liquidbleach and fabric softener to the appropriatecompartments. Slowly close dispenser drawer. Thewasher will not operate with the drawer open.
6. Set Temperature switch according to fabric typeand soil level of each load.
7. If desired, select Extra Rinse in Whites/Regular,Colors/Perm Press, or Delicates cycle.
8. Select Final Spin Speed as desired.
9. Push in the cycle selector knob and turn itclockwise to the desired wash cycle and setting.
10. Start the washer by closing the door andpulling out the cycle selector knob. The washerwill not operate with the door open. As a safetymeasure, the door will automatically lock duringthe entire wash cycle. When the door is closed,the Door Lock Indicator lights up when thewasher starts, and turns off at the end of thecycle.
To stop the washer, push in the cycle selector knob.
To change a cycle, push in the cycle selector knoband turn it clockwise to the desired setting.
Pull out the knob to restart the washer.
11. Remove items when cycle ends. A signal will soundat the end of the cycle.
Note: From time to time you may see water in the bleach and fabric softener compartments. This is a result of the siphoning action and is part of the normal operation of the washer.
Cycle Selection
For best results, follow the fabric care label directionson items to be washed.
Whites/Regular Cycle
Up to 18 minutes of reversing tumble action for mostfabrics. Three rinses, three spins, a pause and a brieftumble complete the cycle. Select NORMAL or FASTFinal Spin as desired.
-
31
Heavy Wash provides up to 18 minutes of reversingtumble action for heavily soiled fabrics.
Wash provides up to 13 minutes of reversing tumbleaction for normally soiled fabrics.
Light Wash provides up to 6 minutes of reversingtumble action for lightly soiled fabrics.
Short Wash Cycle
Saves time and water. Up to 6 minutes of reversing tumbleaction for very lightly soiled fabrics. Two rinses, two spins,a pause and a brief tumble complete the cycle. ExtraRinse is not an option with this water conserving cycle.Select NORMAL or FAST Final Spin as desired for thiscycle.
Colors/Perm Press Cycle
Up to 13 minutes of reversing tumble action for cottonsand blends with a no-iron finish. Three rinses, three spins,a pause and a brief tumble complete the cycle. SelectNORMAL or FAST Final Spin as desired for this cycle.
Wash provides up to 13 minutes of reversingtumble action for heavily soiled fabrics.
Extra Care provides up to 6 minutes of reversingtumble action for lightly soiled fabrics.
Knits and Delicates Cycle
Up to 10 minutes of gentle tumble action for the gentlecare of knit, delicate and hand washable items. Tworinses and two spins complete the cycle. Select NOR-MAL or FAST Final Spin as desired for this cycle.
Controls
Always follow instructions on fabric care labels.
Note: There is no need to select a water level because the washer automatically adjusts the water level to the type and size of wash load.
TEMPERATURES - This determines water temperaturesfor washing and rinsing. For example, the Warm/Coldsetting provides a warm water wash and a cold waterfinal rinse.
Note: Detergents are not as effective at wash water temperatures below 65F (18.3C).
The following chart suggests wash/rinse temperaturesfor basic fabric types.
CYCLE SIGNAL - A signal will sound at the end of thecycle.
When the door is closed, the Door Lock Indicatorlights up when the cycle selector knob is pulled out, andturns off at the end of the cycle.
EXTRA RINSE - Use Extra Rinse when additional rins-ing is desired to remove excess dirt and detergent fromheavily soiled loads.
Select Extra Rinse On to automatically include anextra rinse in Whites/Regular, Colors/Perm Press,or Delicates cycle.
Select Extra Rinse Off to conserve water when anextra rinse is not desired.
FINAL SPIN - There are two final spin speed optionsavailable for each cycle. Note: The speeds will vary fromcycle to cycle. For example, Regular Fast spin speedis much faster than Delicate Fast spin speed.
NORMAL is recommended for most loads.
FAST provides a faster spin speed to increasewater extraction and decrease drying time.
-
32
Section D - Owner GuideTumble Action Laundry Center
For your safety, the information in this manual mustbe followed to minimize the risk of fire or explo-sion or to prevent property damage, personal in-jury or loss of life.
- Do not store or use gasoline or other flammablevapors and liquids in the vicinity of this or any otherappliance.
- WHAT TO DO IF YOU SMELL GAS: Do not try to light any appliance. Do not touch any electrical switch; do not use any phone in your building. Clear the room, building or area of all occupants. Immediately call your gas supplier from a neighbors phone. Follow the gas suppliers instructions. If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualifiedinstaller, service agency or the gas supplier.
Product Registration
Thank you for choosing this laundry center. Thisowners guide will explain proper operation and care.
Record Your Model and Serial Numbers
Record below the model and serial numbers found onthe laundry center serial plate located on the inside ofthe dryer door. Keep these numbers for future reference.
Model Number __________________Serial Number ___________________Date of Purchase ________________
Register Your Product
The self-addressed PRODUCT REGISTRATION CARDshould be filled in completely, signed and returned.
This Owners Guide provides general operating instruc-tions for your laundry center. It also contains informationabout features for several other models. Your laundrycenter may not have every feature included here. Usethe laundry center only as instructed in this OwnersGuide and the Operating Instructions included withyour laundry center.
2000 White Consolidated Industries, Inc. All rightsreserved.
Important Safety Instructions
Read all instructions before using this laundry cen-ter.
To reduce the risk of fire, electricalshock, or injury to persons whenusing this laundry cen-ter, comply with the basic warnings listed below.
Failure to comply with these warnings could resultin serious personal injuries.
Prevent Fire
Do not wash or dry items that havebeen previously cleaned in, soaked in, or spotted withgasoline, cleaning solvents, kerosene, waxes, etc. Donot store these items on or near the dryer. These sub-stances give off vapors that could ignite or explode.
Do not put oily or greasy rags or cloth-ing on top of the laundry center. These substances giveoff vapors that could ignite the materials.
Do not add gasoline, cleaning sol-vents, or other flammable or explosive substances tothe wash water. These substances give off vapors thatcould ignite or explode.
Under certain conditions, hydrogengas may be produced in a hot water system that has notbeen used for 2 weeks or more. HYDROGEN GAS ISEXPLOSIVE. If the hot water system has not been usedfor such a period, before using the washer, turn on all hotwater faucets and let the water flow from each for severalminutes. This will release any accumulated hydrogengas. Hydrogen gas isflammable; do not smoke or usean open flame during this time.
To prevent fire, do not use heat to dryitems containing plastic, foam rubber or similarly tex-tured rubber-like materials, or items containing feathersor down. Use Air Fluff (No Heat) only.
Clean the dryer lint screen before orafter each load. The interior of the dryer, lint screen hous-ing and exhaust duct should be cleaned approximatelyevery 18 months by qualified service personnel. An ex-cessive amount of lint build-up in these areas could re-
-
33
sult in inefficient drying and possible fire. See Care andCleaning.
Do not operate the dryer if the lintscreen is blocked, damaged or missing. Fire hazard,overheating and damage to fabrics can occur. If yourdryer has a drying rack, always replace the lint screenwhen finished using the drying rack.
This Owners Guide provides general operating instruc-tions for your laundry center. It also contains informationabout features for several other models. Your laundrycenter may not have every feature included.
Use the laundry center only as instructed in this OwnersGuide.
Avoid fire hazard or electrical shock.Do not use an adaptor plug or extension cord or removegrounding prong from electrical power cord. Failure tofollow this warning can cause serious injury, fire or death.
GAS LAUNDRY CENTERS:
Grounding type wall receptacle
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vaporsor liquids in the vicinity of this or any other appliance.
Note: The instructions appearing in this Owners Guideare not meant to cover every possible condition andsituation that may occur. Common sense and cautionmust be practiced when installing, operating andmaintaining any appliance.
Keep area around the exhaust open-ing and surrounding areas free from the accumulation oflint, dust and dirt.
Do not obstruct the flow of ventilatingair. Do not stack or place laundry or throw rugs againstthe front or back of the laundry center.
Do not spray any type of aerosol into,on or near laundry center at anytime.
Do not use fabric softeners or prod-ucts to eliminate static unless recommended by themanufacturer of the fabric softener or product.
Do not place items exposed to cook-ing oils in your dryer. Items contaminated with cookingoils may contribute to a chemical reaction that couldcause a load to catch fire.
Failure to comply with these warnings could resultin fire, explosion, serious bodily injury and/or damage tothe rubber or plastic parts of the laundry center.
Protect Children
Do not allow children to play on or inthe laundry center. Close supervision of children is nec-essary when the laundry center is used near children.As children grow, teach them the proper, safe use of allappliances.
Destroy the carton, plastic bag andother packing materials after the laundry center is un-packed. Children might use them for play. Cartons cov-ered with rugs, bedspreads or plastic sheets can be-come airtight chambers.
Keep laundry products out ofchildrens reach. To prevent personal injury, observe allwarnings on product labels.
Before the laundry center is removedfrom service or discarded, remove the washer lid anddryer door to prevent accidental entrapment.
Failure to comply with these warnings could resultin serious personal injuries.
Prevent Injury
To prevent shock hazard and assure
-
34
stability during operation, the laundry center must beinstalled and electrically grounded by a qualified serviceperson in accordance with local codes. Installation in-structions are packed in the laundry center for theinstallers reference. Refer to INSTALLATION INSTRUC-TIONS for detailed grounding procedures. If the laundrycenter is moved to a new location, have it checked andreinstalled by a qualified service person.
To prevent personal injury or damageto the laundry center, the electrical power cord of a gaslaundry center must be plugged into a properly groundedsystem. Never ground the laundry center to a gaspipe. Do not use an extension cord or an adaptorplug.
Follow package directions when us-ing laundry products. Incorrect usage can produce poi-sonous gasresulting in serious injury or death.
Do not combine laundry products for use in 1 loadunless specified on the label.
Do not Do not Do not Do not Do not mixchlorine bleach with ammonia or acids suchas vinegar.
To prevent serious personal injury anddamage to the laundrycenter:
All repairs and servicing must be performedby an authorized servicer unless specificallyrecommended in this Owners Guide. Use onlyauthorized factory parts.
Do not tamper with controls.
Do not install or store the laundry center where itwill be exposed to the weather.
ALWAYS disconnect the laundrycenter from the electrical supply before attempting anyservice or cleaning. Failure to do so can result in electri-cal shock or injury.
Do not use any type of spray cleanserwhen cleaning dryer interior. Hazardous fumes or elec-trical shock could occur.
To prevent injury, do not reach intothe washer while parts are moving. Before loading, un-loading or adding items, push in the cycle selector knoband allow the tub to coast to a complete stop beforereaching inside.
To prevent injury, do not reach intothe dryer if the drum is moving. Wait until the dryer hasstopped completely before reaching into the drum.
A thermal limiter switch automatically turns off thedryer motor in the unlikely event of an overheated situa-tion (electric dryers only). A service technician mustreplace the thermal limiter switch after correcting thefault.
The washer is equipped with an electrical overloadprotector. The motor will stop if it becomes overheated.The washer will automatically restart after a cool downperiod of up to 30 minutes, if the washer has not beenmanually turned off during this time.
Failure to comply with these warnings could resultin serious personal injuries.
Washing Procedures
Follow the guidelines below for preparing the washload.
Read the Washer Operating Instructions foroperating your specific model.
-
35
Always read and follow fabric care andlaundry product labels.
To reduce the risk of fire, electricalshock, or injury to persons, read Important Safety In-structions, before operating this washer.
1. Sort laundry into loads that can be washedtogether.
Sort items by recommended water temperatures, washtime, and agitate/spin speeds.
Separate white, light, and colorfast items from darkand noncolorfast items.
Separate items which shed lint from items whichattract lint. Permanent press, synthetic, knit andcorduroy items will pick up lint from towels, rugsand chenille bedspreads.
Separate heavily soiled items from lightly soileditems.
Separate lacy, sheer and loosely knit items fromsturdy items.
2. Prepare items for washing.
Empty pockets.
Brush off lint and dirt. Shake out rugs and beachtowels.
Close zippers, fasten hooks, tie strings andsashes, and remove nonwashable trims andornaments.
Remove pins, decorative buttons, belt buckles,and other objects which could be damaged. Thisalso helps protect other items in the wash load.
Mend rips and tears to prevent further damageduring washing.
Place delicate items such as bras and hosiery ina mesh bag to prevent tangling during the washcycle.
Turn knit items inside out to prevent pilling.
3. Pretreat stains and heavy soil.See Stain Removal, for details.
4. Add laundry load to washer.
Combine large and small items in a load.
-
36
Load large items first. Large items should notbe more than half the total wash load.
Washing a single item such as a sweater,bath towel or jeans, is not recommended. Asthe machine tumbles the load prior to final spin,it may sense an out-of-balance load. If an out-of-balance load is sensed, the washer will stop brieflyand tumble for a short time to try to balance theload. This stop-tumble action may occur severaltimes before the end of the cycle. If the load cannot be evenly balanced, items may feel wet at theend of the cycle. Adding 1 or 2 similar itemswill help balance the load.
If a load becomes tangled and out-of-balance, itmay be necessary to rearrange the load by hand.Stop the washer by pushing in the cycle selectorknob and open the door. Remove the load, untangle the items and return the load to the tub.Close the door and restart washer.
A single bulky item, such as a bedspread,comforter or sleeping bag, can be launderedwithout adding extra items to the load.
The washer can be fully loaded, but the itemsshould not be tightly packed. The door should closeeasily.
5. Add detergent, bleach and fabric softener toautomatic dispenser following these steps:
A. OPENING AND CLOSING THE DISPENSERDRAWER
Slowly open the dispenser drawer by first slidingthe safety latch to the right, then pulling the drawerout until it stops.
After adding laundry products, slowly close thedispenser drawer. Closing the drawer too quickly
could result in early dispensing of the bleach andfabric softener.
B. DETERGENT
Laundry products used with powder or liquiddetergent, such as color-safe bleach, waterconditioner, detergent booster, and enzymeproducts should be added to the empty tub beforeloading.
Add measured detergent to the detergentcompartment of the dispenser drawer.
Detergent is flushed from the dispenser at thebeginning of the cycle. Either powdered or liquiddetergent can be used. Note: Liquid detergent willdrain into the washer drum as it is added.
High efficiency (HE), low sudsing detergent isrecommended for this washer. Use themanufacturers recommended amount.
If low sudsing detergent is not available, a reducedamount of regular detergent may be used. Because reducing the amount of detergent mayreduce cleaning, it is important to pretreat stains,sort carefully by color and soil level, and avoidoverloading.
Detergent usage may need to be adjusted forwater temperature, water hardness, size and soillevel of the load.
For best results, avoid oversudsing.
C. LIQUID BLEACH LIQUID BLEACH LIQUID BLEACHLIQUID BLEACH LIQUID BLEACH
-
37
Note: From time to time you may see water in the bleachand fabric softener compartments. This is a result of thesiphoning action and is part of the normal operation ofthe washer.
If desired, measure out the recommended amountof liquid chlorine bleach (not to exceed 1/3 cup(80 mL) and pour it into the center compartmentlabeled Liquid Bleach and marked with thissymbol.
Do not exceed the maximum fill line. Overfillingcan cause early dispensing of the bleach whichcould result in damaged clothes.
Do not pour undiluted liquid chlorine bleachdirectly onto the load or into the drum. Fabricdamage can occur.
Do not use powdered bleach in the dispenser.
D. FABRIC SOFTENER
If desired, pour the recommended amount offabric softener into the compartment labeled Fabric Softenerand marked with this symbol .
Dilute concentrated softeners with warm water tothe Fill Line.
Do not exceed the maximum fill line. Overfillingcan cause early dispensing of the fabric softenerwhich could result in stained clothes.
Do not pour fabric softener directly on the washload.
Use of a fabric softener dispensing ball is notrecommended in tumble action washers.
6. Set cycle selector knob and washer controlsaccording to type, size, and soil level of each load.
(See Operating Instructions card for your specificmodel controls.)
7. Start the washer.
Close the washer door and pull out the cycleselector knob. For your safety, the door willautomatically lock during the entire wash cycle. TheDoor Lock indicator light will remain lit until the cycleends.
Washer will fill and tumble.
To stop the washer, push in the cycle selectorknob.
To open the door during tumbling, push in the cycleselector knob. Wait for the water to run off of thedoor.
To change a cycle, push in the cycle selector knoband turn it clockwise to the desired setting. Pullout the knob to restart the washer.
-
38
To open the door during a spin cycle, push in thecycle selector knob. The Door Lock indicator lightwill turn off. Wait 1-2 minutes for the lock torelease. The door can then be opened. Do notforce open the locked door.
8. Remove items when the cycle is completed.
Place washed items in automatic dryer, line dry, ordry flat as directed by fabric care label. Excesswrinkling, color transfer or odors may develop in itemsleft in the washer after the cycle has ended.
9. General Precautions
If the dispenser drawer is pulled out more than1-1/2" when the washer is in operation, thewasher will shut off. The Door Lock indicator lightwill turn off and the door will be unlocked. Slowlyclose the drawer, and the washer willutomatically resume operation.
Do not slam the washer door closed or try toforce the door open when locked (Door Locklight ON). This could result in damage to thewasher.
DO NOT leave the washer door open. An opendoor could entice children to hang on the door orcrawl inside the washer.
To avoid damaging the washer and personalinjury, DO NOT hang on or lean against the washerdoor.
Do not store or place laundry productson top of laundry center at any time.They can damage the finish or controls.
Do not place detergent, bleach or fabric softenercontainers on top of the washer. They candamage the finish or controls.
Stain Removal
Safe Stain Removal Procedures
To reduce the risk of fire or seriousinjury to persons or property, comply with the basic warn-ings listed below:
Read and comply with all instructions on stainremoval products.
Keep stain removal products in their originallabeled containers and out of childrens reach.
Thoroughly wash any utensil used.
Do not combine stain removal products, especiallyammonia and chlorine bleach. Dangerous fumesmay result.
Never wash items which have been previouslycleaned in, washed in, soaked in or spotted withgasoline, dry cleaning solvents or other flammableor explosive substances because they give offvapors that could ignite or explode.
Never use highly flammable solvents, such asgasoline, inside the home. Vapors can explodeon contact with flames or sparks.
-
39
For successful stain removal: Remove stains promptly. Determine the kind of stain, then follow the recommended treatment in the
stain removal chart below. To pretreat stains, use a prewash product, liquid detergent, or a paste made
from granular detergent and water. Use cold water on unknown stains because hot water can set stains. Check care label instructions for treatments to avoid on specific fabrics. Check for colorfastness by testing stain remover on an inside seam. Rinse and wash items after stain removal.
StainAdhesive tape, chewinggum, rubber cement
Baby formula, dairyproducts, egg
Beverages (coffee, tea,soda,juice, alcoholic beverages)
Blood
Candle wax, crayon
ChocolateCollar or cuff soil,cosmeticsDye transfer on whitefabricGrass
Grease, oil, tar (butter,fats,salad dressing, cookingoils,car grease, motor oils)
Ink
Mildew, scorch
Mud
Mustard, tomato
Nail polish
Paint, varnish
Perspiration
Rust, brown or yellowdiscoloration
Shoe polish
Urine, vomit, mucus, feces
TreatmentSTAIN REMOVAL
Follow fabric carelabel instructions.
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stainremover or nonflammable dry cleaning fluid.
Use product containing enzymes to pretreat or soak stains. Soak for 30 minutes or more. Wash.
Pretreat stain. Wash using cold water and bleach safe for fabric.
Rinse with cold water. Rub with bar soap. Or, pretreat or soak with product containing enzymes. Washusing bleach safe for fabric.
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until waxis absorbed. Replace paper towels frequently. Treat remaining stain with prewash stain remover ornonflammable dry cleaning fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.
Pretreat with prewash stain remover or rub with bar soap.
Use packaged color remover. Wash using bleach safe for fabric.
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar,apply nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinsethoroughly. Wash using hottest water safe for fabric.
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover,denatured alcohol or nonflammable dry cleaning fluid.
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and hot water before washing.Badly mildewed fabrics may be permanently damaged.
Brush off dry mud. Pretreat or soak with product containing enzymes.
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to backof stain. Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
WATER BASED: Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannotberemoved. OIL BASED AND VARNISH: Use solvent recommended on can label. Rinse thoroughly beforewashing.Use prewash stain remover or rub with bar soap. Rinse. Wash using nonchlorine bleach in hottestwater safe for fabric.For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate detergentand nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.
LIQUID: Pretreat with a paste of granular detergent and water. PASTE: Scrape residue from fabric.Pretreat with prewash stain remover or nonflammable dry cleaning fluid. Rinse. Rub detergent intodampened area. Wash using bleach safe for fabric.
Pretreat or soak in product containing enzymes. Wash using bleach safe for fabric.
-
40
Undiluted liquid detergent orfabric softener dispenseddirectly onto fabric.
Not enough detergent. Wash temperature too low. Incorrect sorting.
Not enough detergent. Undiluted liquid fabric softener
poured directly on fabric.
Incorrect use of chlorine bleach. Unfastened zippers, hooks,
buckles. Rips, tears and broken threads. Overloading the washer. Degradation of fabric.
Incorrect sorting. Tissues left in pocket. Overloading the washer. Not enough detergent. Undissolved detergent has left
a residue resembling lint. Static cling is attracting lint. Load washed too long.
Pilling is normal with syntheticand permanent press fabrics.This is due to abrasion fromnormal wear.
Undissolved detergent. Some nonphosphate granular
detergents can combine withhard water minerals to form aresidue.
Overloading the washer.
Overloading the washer. Incorrect wash cycle for wash
load.
Agitation time too short. Wash water temperature too
low. Not enough detergent.
Iron or manganese in watersupply, water pipes, or waterheater.
Blue stains
Discoloration,graying
Greasy, oilystains
Holes, tears,or snags
Lint
Pilling(Fibers break off, ball up and cling to fabric.)
Residue orpowder ondark items;stiff, harshfabrics.
Wrinkling
Yellowbuildup ofbody soil onsyntheticfabrics
Yellow orbrown ruststains
Avoid overfilling detergent and fabric softener compartments of
dispenser.
Sort items by soil level and color. Use correct amount of detergent,
hottest water and bleach safe forfabric.
Use correct amount of detergentand hottest water safe for fabric.
Do not pour liquid fabric softenerdirectly on fabric. See WashingProcedures on adding softener.
Never pour chlorine bleachdirectly on fabric.
Check condition of items beforewashing. See WashingProcedures for preparing, loadingand adding chlorine bleach.
See Washing Procedures forsorting and preparing the washload.
Do not overload washer. Use correct temperature and
amount of detergent, water andwash time.
Use fabric softener in the washerto lubricate fibers.
When ironing, use spray starchor fabric finish on collars/cuffs.
Turn items inside out to reduceabrasion.
Increase water temperature usinghottest water safe for fabric.
Do not overload washer. Use liquid detergent or use
nonprecipitating water conditionerwith nonphosphate granulardetergent.
Do not overload washer. Remove items from washer as
soon as cycle is completed. Use liquid fabric softener.
Select correct wash cycle. Use correct amount of detergent. Wash synthetics frequently using
hot or warm water.
Use nonprecipitating watersoftener.
Before washing, run hot water fora few minutes to clear lines.
Drain water heater occasionalFor an ongoing problem, install an
iron filter in your water supplysystem.
COMMON WASHING PROBLEMS
SOLUTIONSPROBLEM PREVENTIVE MEASURES
If caused by detergent, mix 1 cup (240 ml)white vinegar with 1 quart (.95 L) water inplasti