6 mandrels

8/12/2019 6 Mandrels

1/17

PRODUCT CATALOG 2009

www.binning-oil-tools.com.ar

Mandrel Catalog

Introduction:

Side Pocket Mandrels:

The original side pocket mandrel was introduced in 1954, since then these mandrels

have come a long way and have suffered various design changes as well as being

adapted to different applications. Side pocket mandrels basically act as receivers for

the different valve types supplied by BINNING OIL TOOLS. These valves are held

inside a specially designed pocket the configuration of which will change depending

on the application desired.

Since 1954 to date, there is an ever increasing number of mandrel designs andoptions offered, from oval mandrels to round solid bar mandrels designed for high

pressure applications. Different alloys are used in their construction being AISI4130

the standard material, but upon request 13Cr,Super 13 Cr, 9Cr and other alloy

materials or combination of materials may be supplied to ensure a long lasting and

trouble free operation in your well.

Mandrels are supplied as standard in AISI 4130 carbon steel with a As per API Spec

hardness, low heat treat mandrels may be supplied with a hardness of up to 22 HRC

to comply with NACE MR0175 specifications for stress corrosion cracking resistantmetallic materials.

Standard configuration is box-box but different configurations as well as thread types

may be supplied ranging from a 2 3/8 to 7 connections.

BINNING OIL TOOLS supplies three basic mandrel lines:

Sect ion 1

Side Pocket Mandrels: Oval and round for use with wireline retrievable valves

Sect ion 2

Conventional Mandrels: For use with tubing retrievable valves

Sect ion 3

Special application mandrels: mandrels specially designed for very specific

applications.


2/17



Sect ion 1

Side Pock et Mandrels

All side pocket mandrels are made from AISI4130 oval seamless tubing, unlessotherwise specified, and each mandrel is hydraulically tested internally to meet

rigorous specifications after a dummy valve has been run into the pocket, as per

API Specification 11V1.

The mandrels manufactured are periodically checked for external pressure as per

API Spec. 11V1.

The mandrels are always described first with the thread nomenclature (2 3/8API

8RD or 3 New Vam, etc.), secondly, with the letter K for 1 pockets or M for 1 pockets, thirdly, with the letter G for a mandrel with an orienting sleeve and D

for the pocket discriminator. These mandrels are usually designed for highly

deviated wells. The last letter usually denotes a special usage or design feature

(E for chamber lift mandrel or W for a waterflood mandrel, etc.)

Round mandrels also have the letter R added to the description with the letters S,

F or B to describe standard (machined), forged o bored (high pressure) pockets.

A mandrel with a number 2 at the end of the description denotes a mandrel with a

reduced external diameter (and a slightly reduced pressure test) but which retains

at least the strength of a reduced coupling (or more) as recommended for API

Reduced Couplings.

Low heat-treated mandrels can be supplied for corrosive wells with H2S or CO2.

A simple K or M only denotes a standard mandrel with lateral outlet and without

an orienting sleeve, tool discriminator or special usage or design features.

Mandrels can be furnished in special alloys depending on working environment,this will be easily identifiable on its denomination. For example: A 9 Chrome oval

seamless tubing will be denoted with in both the description an part number by

adding the sign 9CR in brackets at the end. (2 3/8K (9CR), in case of a 2 3/8 K

series mandrel.


3/17



K Series Side Pocket Mandrel

BINNING OIL TOOLS K series side pocket mandrels are single 1 (25.4mm)

pocket mandrels. This is the basic side pocket mandrel design being rugged

and dependable and is used in thousands of completions world wide.Mandrels are manufactured from oval seamless tubing with full integrally

forged ends (depending on mandrel size).

Applications:

Waterflood, gas lift, chemical injection and any other type of application

where side pocket mandrels are needed.

Main Features:

Manufactured from oval seamless tubing.

Forged ends for most sizes

Accomodates both top or bottom latch valves

Several tubing connection types available.

Box-box configuration as standard but may be supplied as Box-Pin

KW Type mandrel: Same as the K mandrel but specially designed for waterflood

or erosive environment operation, supplied with a case hardened 1 pocket.

KLW Type mandrel: This is a specially designed mandrel ti be used in waterflood

applications with 1 waterflood regulators. These mandrels are slightly longer

than standard K mandrels and are designed to accommodate the 1 valves

extra length and allow for the use of standard wire-line tools.

K-2 Type Mandrel: Same features as the K mandrels but with a reduced OD and

a reduced test pressure. Design has been oriented to maintaining the standarddrift while reducing the maximum OD.

KLT Type Mandrel: A full bore mandrel with a 1 pocket connected to an auxiliary

1 or 1 slip joint for use with a 1 or 1 parallel gas injection line to the

surface.

These gas lift installations are required when the well casing is in bad condition,

pre slotted casing has been run, long perf intervals want to be produced and

running a packer may be impractical or for spotting chemicals through a chemical

injector valve, etc.NOTE: An expansion joint (slip-joint) is needed for each mandrel to connect the

auxiliary gas injection line.


4/17



KE Type Mandrel : A K series mandrel specially designed for chamber lift

applications. The pocket in this mandrel series is equipped with a bottom exit

threaded port where the packer by pass is threaded onto.

Communication to the tubing through the pocket allows for high pressure gas

injected down the tubing to pass through the gas lift valve and into the

chamber.

Engineering Specifications:

Tubing

Size

Des-

cription

Part N Max

O.D.

Min

I.D.

Drift

I.D.

Test Pressure

Standard Service Corrosive Service

Internal External Internal External

2 3/8 K

K-2

KE

KE-2

KW

KLW

KLT

KLT-2

20-K-101

20-K-111

20-K-104

20-K-105

20-K-107

20-K-108

20-K-106

20-K-116

4.25

4.133

4.25

4.133

4.25

4.25

4.750

4.625

1.995

1.995

1.995

1.995

1.995

1.995

1.995

1.995

1.901

1.901

1.901

1.901

1.901

1.901

1.901

1.901

7500psi 6000psi 6000psi 5000psi

2 7/8 K

K-2

KE

KE-2

KW

KLW

KLT

KLT-2

25-K-121

25-K-131

25-K-124

25-K-125

25-K-127

25-K-128

25-K-126

25-K-136

4.710

4.626

4.710

4.626

4.710

4.710

5.126

5.055

2.441

2.441

2.441

2.441

2.441

2.441

2.441

2.441

2.347

2.347

2.347

2.347

2.347

2.347

2.347

2.347

3 KK-2

30-K-14830-K-141

5.5005.343

2.9922.992

2.8672.867

Note: Test pressures may vary depending on connection type or alloy.

Standard service is understood as AISI4130 low carbon seamless tube heat treated to

HHT Specs.

Corrosive service is understood as AISI4130 low carbon seamless tube heat treated to22 HRC under NACE MR0175 specifications for stress corrosion cracking resistant

materials.


5/17



KGD Series Side Pocket Mandrel

BINNING OIL TOOLS KGD are based on the K series design but

incorporate an orienting sleeve as well as a tool discriminator above the

pocket to exclude larger slickline tools and prevent them hanging up inhighly deviated wells. The orienting sleeve aids in the positive alignment of

a specially designed kickover tool.

Applications:

Waterflood, gas lift, chemical injection and any other type of

application where side pocket mandrels are needed. Deviated or vertical wells where precise alignment of kickover tool is

desired to ease insertion and retrieval operations.

Main Features:



Accomodates both top or bottom latch valves Several tubing connection types available.


Orienting sleeve which guarantees positive alignment of slickline tools

Pocket discriminator which ensures larger tools do not hang up on

the pocket and are deviated to the well bore.

KGD-2 Type Mandrel: Same features as the KGD mandrels but with a

reduced OD and a reduced test pressure. Design has been oriented to

maintaining the standard drift while reducing the maximum OD.

KGDLT Type Mandrel: A full bore mandrel with a 1 pocket connected to an

auxiliary 1 or 1 slip joint for use with a 1 or 1 parallel gas injection line

to the surface.

These gas lift installations are required when the well casing is in bad

condition, pre slotted casing has been run, long perf intervals want to be

produced and running a packer may be impractical or for spotting chemicals

through a chemical injector valve, etc.NOTE: An expansion joint (slip-joint) is needed for each mandrel to connect

the auxiliary gas injection line.


6/17



KGE Type Mandrel : A K series mandrel specially designed for chamber lift

applications. The pocket in this mandrel series is equipped with a bottom exit

threaded port where the packer by pass is threaded onto. Communication to the

tubing through the pocket allows for high pressure gas injected down the tubing to

pass through the gas lift valve and into the chamber.


Tubing

Size

Description Part

N

Max.

O.D.

Min

I.D.

Drift

I.D.

Test Pressure



2 3/8 KGD

KGD-2

KGDLT-2

20-K-103

20-K-113

20-K-115

4.250

4.133

4.650

1.995

1.995

1.995

1.901

1.901

1.901

7500psi 6000psi 6000psi 5000psi

2 7/8 KGD

KGD-2

KGDLT-2

25-K-123

25-K-133

25-K-139

4.710

4.626

5.055

2.441

2.441

2.441

2.347

2.347

2.347

3 KGD

KGD-2

30-K-146

30-K-143

5.500

5.343

2.992

2.992

2.867

2.867


Standard service is understood as AISI4130 low carbon seamless tube heat treated as per

API Spec.

Corrosive service is understood as AISI4130 low carbon seamless tube heat treated to 22

HRC under NACE MR0175 specifications for stress corrosion cracking resistant materials.


7/17



M Series Side Pocket Mandrel

BINNING OIL TOOLS M series side pocket mandrels are single 1

(38.1mm) pocket mandrels. This is the basic side pocket mandrel design

being rugged and dependable an is used in thousands of completions worldwide. Mandrels are manufactured from oval seamless tubing with full

integrally forged ends (depending on mandrel size).

Applications:


where side pocket mandrels are needed.

Main Features:



Accomodates both top or bottom latch valves



MW Type mandrel: Same as the M mandrel but specially designed for

waterflood or erosive environment operation, supplied with a case hardened

1 1/2 pocket.

M-2 Type Mandrel: Same features as the M mandrels but with a reduced OD

and a reduced test pressure. Design has been oriented to maintaining the

standard drift while reducing the maximum OD.

MLT Type Mandrel: A full bore mandrel with a 1 1/2 pocket connected to an

auxiliary 1 or 1 slip joint for use with a 1 or 1 parallel gas injection line

to the surface.These gas lift installations are required when the well casing is in bad condition,

pre slotted casing has been run, long perf intervals want to be produced and

running a packer may be impractical or for spotting chemicals through a

chemical injector valve, etc.

NOTE: An expansion joint (slip-joint) is needed for each mandrel to connect the

auxiliary gas injection line.

ME Type Mandrel : A M series mandrel specially designed for chamber lift

applications. The pocket in this mandrel series is equipped with a bottom exitthreaded port where the packer by pass is threaded onto. Communication to

the tubing through the pocket allows for high pressure gas injected down the

tubing to pass through the gas lift valve and into the chamber.


8/17



MKW Type Mandrel: The MKW type mandrel is a mandrel with a 1 pocket

welded in a K type vessel with a reduced bore. It is normally required by those who

need to run a 1 diameter waterflood regulator in 5 casing with 2 7/8 tubing.

The 1 pocket is case hardened at the lateral exit to withstand water erosionbetter. Note: Due to reduced ID a L type kickover tools with a maximum OD

retracted of 1.850 or a K type kicover tool with flexible arms should be used in

these mandrels.


TubingSize Description Part N Max.O.D. Min I.D. DriftI.D. Test Pressure



2 3/8 M

M-2

ME

ME-2

MW

20-M-161

20-M-171

20-M-164

20-M-174

20-M-166

4.740

4.626

4.740

4.626

4.740

1.995

1.995

1.995

1.995

1.995

1.901

1.901

1.901

1.901

1.901

7500psi 6000psi 6000psi 5000psi

2 7/8 M

M-2

ME

MKWMW

MKW-2

25-M-181

25-M-182

25-M-184

25-M-18625-M-187

25-M-195

5.500

5.500

5.500

4.710

5.500

4.626

2.441

2.441

2.441

1.900

2.441

1.900

2.347

2.347

2.347

1.900

2.347

1.900

3 M

M-2

30-M-191

30-M-201

5.968

5.750

2.992

2.992

2.867

2.867

4 M

MW

45-M-458

45-M-445

7.031

7.031

3.958

3.958

3.833

3.833



As per API Spec.

Corrosive service is understood as AISI4130 low carbon seamless tube heat treated to

22 HRC under NACE MR0175 specifications for stress corrosion cracking resistant

materials.


9/17



MGD Series Side Pocket Mandrel

BINNING OIL TOOLS MGD are based on the M series design but

incorporate an orienting sleeve as well as a tool discriminator above the

pocket to exclude larger slickline tools and prevent them hanging up inhighly deviated wells. The orienting sleeve aids in the positive alignment of

a specially designed kickover tool.

Applications:

Waterflood, gas lift, chemical injection and any other type ofapplication where side pocket mandrels are needed.

Deviated or vertical wells where precise alignment of kickover tool is

desired to ease insertion and retrieval operations.





Orienting sleeve which guarantees positive alignment of slickline tools

Pocket discriminator which ensures larger tools do not hang up on

the pocket and are deviated to the well bore.

Main Features:

MGD-2 Type Mandrel: Same features as the MGD mandrels but with a

reduced OD and a reduced test pressure. Design has been oriented to

maintaining the standard drift while reducing the maximum OD.


10/17




TubingSize Description Part N Max.O.D. MinI.D. DriftI.D. Test Pressure



2 3/8 MGD

MGD-2

MGDW

20-M-163

20-M-173

20-M-168

4.740

4.626

4.740

1.995

1.995

1.995

1.901

1.901

1.901

7500psi 6000psi 6000psi 5000psi

2 7/8 MGD

MGD-2

MGDW

25-M-183

25-M-170

25-M-194

5.500

5.396

5.500

2.441

2.441

2.441

2.347

2.347

2.347

3 MGD

MGD-2

30-M-199

30-M-203

5.968

5.750

2.992

2.992

2.867

2.867

4 MGD 45-M-444 7.031 3.958 3.833

7 MGD 70-M-470 9.375 6.184 6.059



As per API Spec.

Corrosive service is understood as AISI4130 low carbon seamless tube heat treated

to 22 HRC under NACE MR0175 specifications for stress corrosion cracking resistant

materials.


11/17



Round High Pressure Side Pocket Mandrels

BINNING OIL TOOLS R series side pocket mandrels are single pocket

high pressure mandrels. The design of these mandrels are the based on

standard side pocket mandrels design which have proven rugged anddependable being used in thousands of completions world wide.

Applications:

High pressure gas-lift, chemical injection, waterflood and other

applications.

Round geometry ensures a high burst/collapse resistance

Solid body type mandrels

Accomodates both top or bottom latch valves (in the KR version)


Box-pin configuration as standard but may be supplied as Box-box

Main Features:

KR Type mandrel: Solid body 1 side pocket mandrel. Round geometry ensure

superior burst/collapse pressures resistance.

KGDR Type mandrel:. are based on KR series design but incorporate an

orienting sleeve as well as a tool discriminator above the pocket to exclude

larger slickline tools and prevent them hanging up in highly deviated wells.

The orienting sleeve aids in the positive alignment of a specially designed

kickover tool.

MR Type Mandrel: Solid body 1 1/2 side pocket mandrel. Round geometry

ensure superior burst/collapse pressures resistance.

MGDR Type mandrel:. are based on MR series design but incorporate an

orienting sleeve as well as a tool discriminator above the pocket to exclude

larger slickline tools and prevent them hanging up in highly deviated wells.

The orienting sleeve aids in the positive alignment of a specially designed

kickover tool.

In most sizes round geometry offers a reduced OD.

Other pocket configurations are available upon request.


12/17




Tubing

Size

Description Part N Max.

O.D.

Min

I.D.

Drift

I.D.

Test Pressure



4 KGDRS

KGDRF

KGDRB

45-K-452

45-K-453

45-K-258

5.987

5.987

5.987

3.958

3.958

3.958

3.833

3.833

3.833

11000

11000

12500

10000

10000

12000

6500

6500

7500

6000

6000

6500

MGDRS

MGDRF

MGDRB

45-M-454

45-M-455

45-M-460

7.250

7.250

7.250

3.958

3.958

3.958

3.833

3.833

3.833

9500

9500

11000

9000

9000

10000

6500

6500

8500

6000

6000

7500

5 MGDRS

MGDRF

MGDRB

55-M-456

55-M-208

55-M-457

7.810

7.810

7.810

4.778

4.778

4.778

4.653

4.653

4.653

9500

9500

11000

8500

8500

10000

6500

6500

7000

6000

6000

6500


Standard service is understood as AISI4130 low carbon seamless tube heat treated to As

per API Spec.

Corrosive service is understood as AISI4130 low carbon seamless tube heat treated to

22 HRC under NACE MR0175 specifications for stress corrosion cracking resistant

materials.

TYPE B TYPE F TYPE S


13/17



Conventional Mandrels

BINNING OIL TOOLS C series conventional mandrels are specially designed

to be used with tubing retrievable valves.This is the basic side pocket mandrel

design being rugged and dependable and is used in thousands of completionsworld wide. Mandrels are manufactured from one-piece seamless pup joints.

Applications:


where mandrels are needed.

Manufactured from seamless one piece pup joints.

Forged ends.

Accommodate all tubing retrievable valves and check-valves


Box-pin configuration as standard (coupling is used)

All mandrels fully drifted and hydro tested.

Main Features:

CO Type mandrel: Conventional tubing retrievable mandrel with connecting lug

where valve or check is threaded and a protective top lug to prevent valve damage

during running or retrieving procedures. Designed for 1, 1 and 5/8 valves.

COB Type mandrel: Similar to CO type but with the addition of two steel plates

welded parallel to valve designed to offer extra protection of installed devices.

COF Type Mandrel: Similar to the CO mandrel but the pocket is near the middle of

the mandrel and is designed for annular flow or fluid operated valves.


14/17



COLT Type Mandrel: Design is based on the CO mandrels but this mandrel

incorporates a side pipe connected to the pocket through which gas is injected in

side pipe gas lift designs where casing or long perforated intervals prove

standard gas lift as inefficient.

Tubing Size Description Part N Max.

O.D.

Valve

dia.

Test Pressure

2 3/8 EUE CO06

CO10

CO10B

CO15

CO15B

COF10

20-CO-750

20-CO-751

20-CO-765

20-CO-752

20-CO-766

20-CO-753

3.57

3.78

3.78

4.38

4.38

4.10

5/8

1

1

1

1

1

6000psi

2 3/8 NUE CO06

CO10

CO10B

CO15

CO15B

COF10

20-CO-760

20-CO-761

20-CO-785

20-CO-762

20-CO-786

20-CO-763

3.07

3.69

3.69

4.29

4.29

4.01

5/8

1

1

1

1

1

6000psi

2 7/8EUE C010

C010B

CO15

CO15B

COF10

COF15

25-CO-770

25-CO-769

25-CO-771

25-CO-767

25-CO-772

25-CO-773

4.33

4.33

4.92

4.92

4.70

5.26

1

1

1

1

1

1

6000psi

3 EUE CO10

CO10B

CO15

CO15B

30-CO-780

30-CO-787

30-CO-781

30-CO-788

5.06

5.06

5.66

5.66

1

1

1

1

6000psi


Standard service is understood as N80-L80 low carbon seamless tube heat treated as per

API Spec.

Corrosive service is understood as heat treated to 22 HRC under NACE MR0175

specifications for stress corrosion cracking resistant materials.



15/17



Concave and annular mandrels

BINNING OIL TOOLS special application conventional mandrel product line offers

a wide range of designs for custom built applications such as, chamber, macaroni,

coiled tubing, slim hole or pack-off applications.

Applications:

Gas lift, chemical injection and any other type of application where

mandrels are needed where small ODs are required.

Wide range of options, sizes and configurations

Carbon steel or high alloys available.

Accommodate standard conventional valves.


Special custom made designs available to adapt to your completion needs.

All mandrels fully drifted and hydro tested.

Main Features:

Concave Type Mandrel: Restricted flow mandrels used in macaroni and pack-

off type gas-lift completions. These concave mandrels with NPT screwed

connections are made to receive standard conventional valves. This mandrel

series is used in applications where tubing flow is required. Mandrel flow

restriction must be considered when selecting.


16/17



Annular Small Tubing Production Mandrel: Mandrels specially designed for

macaroni type completions where gas is injected down the inner string,

through a conventional gas lift valve and up the annulus. This is commonly

used in coiled tubing gas lift application with the appropriate connectors.

Snorkel Type Mandrel: Specially designed, restricted flow mandrel used

only as the bottom mandrel in Macaroni type Gas Lift Chamber Completions.

The NPT screwed connection are made to receive a 1 o.d. type N-10

Gas Lift Valve.

Recommended for use with a type L seating nipple.


17/17

6 mandrels

Documents