600 appliance door & drawer - wren kitchens...600 appliance door & drawer carcass assembly...

900/600+290 Appliance2 Door


600/450+140 Appliance1 Door+2 Drawer

450 Appliance1Door+3 Drawer

A B

C D

2070

2070

2250 Tall

2250 Tall

2070

2070

2250 Tall

2250 Tall

For Internal Use: FI.WR.INS.042_WKIN00142_TOWER_600_DrDrwAppRange_Rev2.psd

TOWER UNIT600 Appliance Door & Drawer

Assembly Guide

BEFORE YOU START

INSTALLATION SHOULD BE

PERFORMED BY A COMPETENT

PERSON ONLY.

THIS PRODUCT COULDBE DANGEROUSIF INCORRECTLY

INSTALLED

REQUIRED TOOLS

NOT to be used with CAM DOWEL

& CAM LOCK

STANDARD DRAWER (packed separately)Fitting pack contents

DEEP DRAWER (packed separately)Fitting pack contents

(M) x2Cover Cap

(R) x 14Drawer Runner

16mm Screws

(R) x 14Drawer Runner16mm Screws

(N) x 1Door Buffer

(N) x 1Door Buffer

(S) x221mm Screw

(S) x221mm Screw

(L) x 2Gallery Head

(M) x 2Drawer

Cover Caps

METAL BACK PANELx 1

DRAWER SIDEx1 Right Hand

DRAWER SIDEx1 Left Hand

DRAWER BASEx 1

DRAWER RUNNERx 1 Right Hand

FRONTALx 1 (Supplied separately)

DRAWER RUNNERx 1 Left Hand

DRAWER FRONT FIXING

x 2

METAL BACK PANELx 1

DRAWER SIDEx1 Right Hand

DRAWER SIDEx1 Left Hand

DRAWER BASEx 1

DRAWER RUNNERx 1 Right Hand

FRONTALx 1 (Supplied separately)

DRAWER RUNNERx 1 Left Hand

DRAWER FRONT FIXING

x 2

GALLERY RAIL

x 2

For Internal Use: FI.WR.INS.042_WKIN00142_TOWER_600_DrDrwAppRange_Rev2.psdPage 1


Drawer Assembly

Metal back panel

Step 1.Secure drawer base to drawer side using 4 x 16mm drawer runner screws (R) in holes provided.

Seat the edge of drawer base tight into corner of casing, as shown.

The decorative face of drawer base to be positioned as shown.

Repeat step 1 so both drawer sides areattached to drawer base. Step 2.

Clip on metal back panelto drawer base & drawer sides

Step 3.Screw back panel in position using 2 x 16mm screws (R) to drawer base in holes provided.

DRAWER BASEWhite decorative

face up

Metal back panel

Decorative face

Drawer base

DRAWER BASE

R

R

R

R

R

View from backFront of drawer

R

R

R

R

R

R

S

Secure frontal fixing clip to drawer frontal using 2 x 21mm screw (S) into the pilot holes provided as shown.

Step 4.Frontal attachment

STANDARDDRAWER

Fixing clipStep 5.Draw adjustmentScrew point 1 as shown to adjust drawer frontal right & left.

Screw point 2a as shown to adjust drawer frontal up & down.Tighten 2b once in position.

Standard drawer view

Fixing clip& (S)

Fixing clip& (S)

STANDARDDRAWER

S

Releasing Fixing ClipScrew point 3 whilst applying

downward pressure as shown to release

View on side of drawer side

For Internal Use: FI.WR.INS.042_WKIN00142_TOWER_600_DrDrwAppRange_Rev2.psd Page 2


Standard Drawer Assembly

DRAWER BASE



Deep DrawerAssembly

Page 3

Step 2.Clip on metal back panel to drawer base & drawer sides.

Step 3.Screw back panel in positionusing 2 x 16mm screws (R) to drawer base in holes provided.

Step 1.Secure drawer base to drawer side using 4 x 16mm drawer runner screws (R) in holes provided.

Seat the edge of drawer base tight into corner ofcasing, as shown.

The decorative face ofdrawer base to be positioned as shown.

Repeat step 1 so both drawer sides are attached to drawer base.

Secure frontal fixing clip to drawer frontal using 2 x 21mm screw (S) into the pilot holes provided, as shown.

Screw point 2a as shown to adjust drawer frontal up & down.Tighten 2b once in position

View from back

Front of drawer

View on side of drawer side

Decorative face

Drawer base

Deep drawer

Fixing clip

Fixing clip& screw

Fixing clip& screw

S & L S & L

S

S

L

S

1 3 2b 2a

Deep drawer view

Metal back panel

Metal back panel

DRAWER BASEwhite decorative

face up

R

R

R

R

R

R

R

R

R

R

R

Step 4.Frontal AttachmentSecure gallery head (L) using 1 x15mm screw (S) into the pilot hole provided.

Step 5.Draw AdjustmentScrew point 1 as shown to adjust drawer frontal right & left.

Releasing Fixing ClipScrew point 3 whilst applying

downward pressure as shown to release

DEEP DRAWER



Assembly Guide

Page 4

BEFORE YOU START

INSTALLATION SHOULD BE

PERFORMED BY A COMPETENT

PERSON ONLY.

THIS PRODUCT COULDBE DANGEROUSIF INCORRECTLY

INSTALLED

REQUIRED TOOLS

NOT to be used with CAM DOWEL

& CAM LOCK

(F) x16 Wooden Dowel

(L) x2415mm Screw

(G) x16Cam Dowel(Expanding)

(H) x12 Cam lock

(M) x4Cover Cap

(K) x1630mmScrew

(S) x3019mmScrew

(N) x2Door Buffer

(N) x12Shelf Peg

Plastic

LGE L BRACKETx2

HINGE MOUNTING PLATEx2 or 4 Inc Screws

HINGEx2 or 4 Where aplicable

(Inc Screws)

(M) x2Fixing Plate

Panel Bx1 End Panel

Panel Ax2 Back Panel

Panel Ex2 Rail

Loose Shelf(where applicable)

x1or 2

Legs Frontals(Packed separately)

Fixed Shelf Cx2 Base Panel



Carcass Assembly

Step 1.To attach drawer runnerscrew into end panels (B) using 2 x 16mm screws (R) per drawer rail, into pilot holes provided, 3rd hole from front, as shown.

Drawer runner position

BR

R

R R

B

37mmfr

om

fro

nt

from base

261mm

C & D74mm

C & D431mm

D789mm

600/450+140 Appliance1 Door+2 Drawer 2070 & 2250 Tall

450 Appliance1Door+3Drawer

2070 & 2250 Talll

C

C

View from underside



Assembly Guide

FOR PANEL(C) POSITIONS SEE SHEET 7

B

B

E

C

CC

C

Step 1.Dowel (F)Seat dowel (F) into holes inboth end panels (B) as shown.

Step 2.Cam Dowel (G)Seat cam dowel (G) into holes inboth end panels (B) as shown.

Step 3.Carcass Construction

Attach Panels (C) & (E) to panels (B),using cam dowel (G) & cam lock (H) (in blue),

and also using dowels (F) (in orange)in positions as shown on.

SEE SHEET 7 or 8 WHERE APPLICABLE.

Seat (G) cam dowelinto hole asshown.

Step 4.Cam Lock (H)Join panels (C) & (E) to (B).Insert cam lock (H). Do NOT tighten until Step 7.

NB. All Cam Locks (H) are to be positioned facing the outside of the unit carcass, for ease of tightening.

Do not use power tools withcam dowel (G) or cam lock (H)

B

C

C

H

HG

G

View from underside View from underside



Carcass Assembly 2070

from basefrom base

126mm94mm

126mm94mm

481mm449mm

481mm449mm

626mm594mm

626mm594mm

1445mm1413mm

1445mm1413mm

1592mm1560mm

1592mm1560mm

1826mm1794mm

1826mm1794mm A B C DA B C D

A B C DA B C D

A B C DA B C D

A BA B

AA

AA

B C DB C D

B C DB C D

BB

BB

AA

AA

B CB C

1468mm1468mm

1322mm1322mm

854mm854mm

711mm711mm

568mm568mm

BTMBTM

TOPTOP

HINGE & FIXED SHELF (B)POSITIONS


2070

900/600+290 Appliance2 Door 2070


2070

600/450+140 Appliance2 Door 2070

CA

B

LEFT HAND RIGHT HAND

DB



Carcass Assembly 2250 Tall

HINGE & FIXED SHELF (B)POSITIONS


2250 Tall


2250 Tall


2070


2250 Tall


2250 Tall

CA DB

from basefrom base

126mm94mm

126mm94mm

481mm449mm

481mm449mm

626mm594mm

626mm594mm

1445mm1413mm

1445mm1413mm

1595mm1563mm

1595mm1563mm

2006mm1974mm

2006mm1974mm A B C DA B C D

A B C DA B C D

A BA B

AA

AA

B C DB C D

B C DB C D

BB

BB

AA

AA

B CB C

1468mm1468mm

1322mm1322mm

854mm854mm

711mm711mm

568mm568mm

BTMBTM

B

LEFT HAND RIGHT HAND

A B C DA B C D TOPTOP



Assembly Guide

Step 5.Cut back panel (A)to suit appliance

option, to leaving thecentre appliance apperture open.

B

A A

A

A

C

C

E

E

Step 6.Slide back panel (A) intogroove of end panels (B).

Once back panel (A) is in position, ensure the panel is flush & square with bottom of end Ppanels (B).

Step 8.Ensure carcass is square. Secure back panel (A) with 12 x 30mm screws (K) equally spaced at the top & bottom of back panels (A) into base panels (C), as shown.

Ensure you screw into the centre of base panel (C) (9mm from the top or bottom edge where applicale).

Step 7.Hand tighten all cam locks (H), this will expand cam dowels (G) and tighten the unit together.

C A

K

K

K

K

A



Assembly Guide

C

B

Step 9.Secure each of the legs into place with 2 x 15mm screws (L).

Step 10.Lightly hit centre peg of leg base with hammer

until flush.

Step 11.Push leg firmly down into leg base.

Adjust legs to 155mm before turning carcass upright. Once in

situ level accordingly.

Ensure legs are rotated as shown so that part of it is supporting the end panels (B).

Front legs should have flat edge to the front.

Front

Leg position diagram

Front

CC

BB



Assembly Guide

Secure tower to the wall using screws through rail panel (E) into the wall as shown.

Screws for fixing to walls are not provided as these vary depending on your wall material and construction. Ensure appropriate fixings for wall constructions are used.

L

L

E

E

Secure tower to the wall using L brackets. Use 2 x 15mm screws (L) to secure each of the L brackets to the cabinets at either side. Then

screw through into the wall as shown.

Screws for fixing to walls are not provided as these vary depending on your wall material

and construction. Ensure appropriate fixings for wall constructions are used.



Assembly Guide

Step 12.Insert hinge in top & bottom holes as shown.

FOR TOWER FRONTALSSEE CUSTOMER SPECIFIC

KITCHEN PLAN

Step 13.Secure hinges by tightening 2 x screws with plastic grommet attached. These are already positioned within the hinges.

Step 14.Attach the door to unit where required. Adjust hinges to suit. See below.

To attach doorclip hinge onto hinge plate and click to secure.

1 2

To Adjust hingeUsing a screwdriver, tighten or loosen as required at Points 1 & 2Point 1 - left - rightPoint 2 - side - side

To Release door Pull catch as shown,to release hinge from the hinge plate.

Fit Cover Caps to Hinge



Assembly Guide

600 appliance door & drawer - wren kitchens...600 appliance door & drawer carcass assembly...

Documents