679-1e - page writer trim i%2c ii%2c iii cardiograph instructions for use for a%2e01
TRANSCRIPT
![Page 1: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/1.jpg)
INSTRUCTIONS FOR USE
PageWriter Trim I, II, III
![Page 2: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/2.jpg)
About This Edition
Published by Philips Medical Systems
Printed in USA
Publication number M4992-91150
Edition History
Edition 3, January 2006Edition 4, March 2006Software Revision A.01.01 and higher
Warranty
Philips Medical Systems reserves the right to make changes to both this Instructions for Use and to the product that it describes. Product specifi-cations are subject to change without notice.
Nothing contained within this Instructions for Use is intended as any offer, warranty, promise, or contractual condition, and must not be taken as such.
Copyright
© 2004-2005 Koninklijke Philips Electronics N.V. All rights are reserved. All other product names are the property of their respective owners.
Reproduction in whole or in part in any form, or by any means, electrical, mechanical or otherwise, is prohibited without the written consent of the copyright holder.
Philips Medical Systems3000 Minuteman RoadAndover, MA 01810 USA(978) 687-1501
Unauthorized copying of this publication may not only infringe copyright laws, but may also reduce the ability of Philips Medical Systems to provide accurate and current information to users.
Compliance
The Philips Medical Systems PageWriter Trim cardiograph complies with all relevant international and national standards and laws. Information on compliance will be supplied on request by a local Philips Medical Systems representative, or by the manufacturer.
Intended Use of this Instructions for Use
This Philips product is intended to be operated only in accordance with the safety procedures and operating instructions provided in this Instruc-tions for Use, and in accor-dance with the purposes for which it was designed. Installation, use, and oper-ation of this product is subject to the laws in effect in the jurisdiction(s) in which the product is being used. Users must only install, use, and operate this product in such a manner that does not conflict with appli-cable laws or regulations that have the force of law. Use of this product for purposes other than the express intended purpose provided by the manufac-turer, or incorrect use and operation, may relieve the manufacturer (or agent) from all or some responsi-bility for resultant non-compliance, damage, or injury.
United States federal law restricts this device to use by or on the order of a
physician. THIS PRODUCT IS NOT INTENDED FOR HOME USE.
Training
Users of this product must receive adequate clinical training on its safe and effective use before attempting to operate the product as described in this Instructions for Use.
Training requirements vary by country. Users must ensure that they receive adequate clinical training in accordance with local laws or regula-tions.
For further information on available training on the use of this product, please contact a Philips Medical Systems representative, or the manufacturer.
Medical Device Directive
The PageWriter Trim Cardiograph complies with the requirements of the Medical Device Direc-tive 93/42/EEC and carries the 0123 mark accord-ingly.
Authorized EU-represen-tative:
Philips Medizin SystemeBöblingen GmbHHewlett Packard Str. 271034 BöblingenGermany
![Page 3: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/3.jpg)
Contents
About the PageWriter Trim Cardiograph
About the Instructions for Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i-iSafety Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i-i
Safety and Regulatory Symbols Marked on the Cardiograph . . . . . . . . . . . . . . . . . . . . . . .i-iSafety Symbols Marked on the Cardiograph Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . i-ii
Important Patient and Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i-ivThe PageWriter Trim Cardiograph . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i-vii
Intended Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i-viiIndications for Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i-vii
The Philips 12-Lead Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i-viiIntended Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i-viiiIndications for Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i-viii
Getting Started
PageWriter Trim Cardiograph Learning Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2About the PageWriter Trim Learning Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Philips 12-Lead ECG XML Information and Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3Using the Philips InCenter Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
About Adobe Acrobat Versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4Attaching the Cardiograph to the Cart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5PageWriter Trim I Cardiograph Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6PageWriter Trim II and III Cardiograph Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8PageWriter Trim II and III Token Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9Patient Interface Module (PIM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
Inserting the Lead Wires into the PIM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11Connecting the PIM to the Cardiograph . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12Placing the PIM in the Holder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
Installing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-14Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15
PageWriter Trim II and III, Battery Charging Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 1-15PageWriter Trim I, Battery Charging Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16
Powering on the Cardiograph. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-17Using the On/Standby Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18
Loading Printer Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19Tips for loading printer paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19
Using the PC Card Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21Using the PC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21Using the Wireless LAN Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22Using the LAN Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-23
Contents-1
![Page 4: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/4.jpg)
Using the Modem Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-23Installing and Removing a PC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-24
Using the USB Memory Stick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-24Using the Barcode Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-25Using the Magnetic Card Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-26Using the SmartCard Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-26Using the Trim Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-27Navigation Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-27
Opening and Closing Screens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-27Opening and Closing Menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-27Selecting Tabs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-28Entering Information on a Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-28Selecting Check Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-29
PageWriter Trim I Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-29Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-30LCD Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-30Function Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-31
PageWriter Trim II and III Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-32PageWriter Trim II and III Status Bar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-33PageWriter Trim II and III Command Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-34
Supplies and Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-35Ordering Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-35PageWriter Trim Cardiograph Supply Part Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . .1-35
Patient Interface Module (PIM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-35Replacement Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-35Complete Lead Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-35Replacement Lead Sets and Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-35Electrodes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-36
Cardiograph Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-37Optional Cardiograph Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-37Printer Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-37Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-37
Contacting a Philips Response Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-38North America Response Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-38South America Response Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-38Europe Response Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-38Asia Response Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-39Africa and Middle East . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-40
PageWriter Trim II and III Configuration
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1Configuring Multiple Cardiographs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1Password Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1Configuring the Wireless LAN Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1Configuration with a Philips TraceMasterVue ECG Management System . . . . . . . . . . . .2-2Restoring Custom Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Contents-2 PageWriter Trim Cardiograph Instructions for Use
![Page 5: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/5.jpg)
Opening the Configuration Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2Analysis Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
About Algorithm Versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3Setting the Default Pacing Detection Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4Setting the Report Status Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6Setting the Default Adult Bradycardia Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7Setting the Philips 12-Lead Algorithm Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7About the Borderline Statement Suppression Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Patient ID Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8Patient ID Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9Configuring Patient Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
User Defined Patient Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11Configuring Clinical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
User Defined Clinical Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14Configuring Order Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
User Defined Order Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17Configuring Auto ECG Report Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
Editing the Profile Report Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20Editing Profile Interpretation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20Editing Profile Scale Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21Editing Report Type Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21Saving the Report Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21Setting the Default Auto Report and Copy Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22Setting Other Print Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23Setting the Default Paper Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24Setting the Caps Lock Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24Printed ECG Lead Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25Default Display Format Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25Battery Power Saving Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25Setting the Notification Message Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26Simulated Waveform Data Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27
Order Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28Rhythm Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29
Filter Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-30About High and Low Pass Frequency Filter Settings . . . . . . . . . . . . . . . . . . . . . . . 2-31Setting Default Rhythm Filter Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32
TraceMasterVue ECG Management System Remote Sites . . . . . . . . . . . . . . . . . . . . . . . . . 2-33Remote Site Fax and Modem Connection (USA and Canada only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34Remote Sites Network Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36
Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38Networking Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39
DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39Fixed IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39
Auto Negotiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39Password Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-40
PageWriter Trim Cardiograph Instructions for Use Contents-3
![Page 6: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/6.jpg)
Lost Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-41Locale Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-41Cardiograph Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-42
Metronome Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-44Magnetic Card Reader Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-45
Saving Configured Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-46Loading the Configuration Settings File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-47Restoring Factory Default Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-48Printing the Configuration Settings Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-48
The Patient Session
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1Patient Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
Instructing the Patient . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2Preparing the Skin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3Attaching the Electrodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3Attaching the Lead Wires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7
Checking Signal Quality. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7Using the PageWriter Trim I Signal Quality Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7
Heart Beat Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8Leads Off Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8Signal Quality Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8Troubleshooting Signal Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9
Using the PageWriter Trim II and III Signal Quality Indicators . . . . . . . . . . . . . . . . . . . . .3-9Using the Leads off indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9Color-coded waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-10Troubleshooting Signal Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11
Using Filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-11Artifact Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12Baseline Wander Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12Frequency Response Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12
About High and Low Pass Frequency Filter Settings . . . . . . . . . . . . . . . . . . . . . . . .3-13Changing Filter Settings on the PageWriter Trim I . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13Changing Filter Settings on the PageWriter Trim II and III . . . . . . . . . . . . . . . . . . . . . . .3-14
Artifact and Baseline Wander Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-16Display Filter Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-16
Entering Patient ID Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-17Entering Patient ID Information on the PageWriter Trim I . . . . . . . . . . . . . . . . . . . . . .3-17
Entering Patient ID Information on the PageWriter Trim II and III. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18
Entering Patient ID Information with the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-19Opening a Pending Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-19
Using the Orders Quick Search Feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-20Entering Patient ID Information with the Barcode Reader . . . . . . . . . . . . . . . . . . . . . . .3-21Entering Patient ID Information with the Magnetic Card Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-22
Contents-4 PageWriter Trim Cardiograph Instructions for Use
![Page 7: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/7.jpg)
Entering Patient ID Information with the SmartCard Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23Editing Patient ID Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
Emergency (STAT) ECGs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24Taking a STAT ECG with the PageWriter Trim I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24Taking a STAT ECG with the PageWriter Trim II and III . . . . . . . . . . . . . . . . . . . . . . . 3-24
Taking an Auto ECG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25Taking an Auto ECG with the PageWriter Trim I. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25Taking an Auto ECG with the PageWriter Trim II and III. . . . . . . . . . . . . . . . . . . . . . . 3-26
The Preview Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26Changing Auto ECG Report Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26Using the Metronome with Auto ECG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27
Rhythm ECG Acquisition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28Taking a Rhythm Report on the PageWriter Trim I . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28Taking a Rhythm Report on the PageWriter Trim II and III . . . . . . . . . . . . . . . . . . . . . 3-29
Disclose ECG Acquisition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30Pacing Detection Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31Getting Help on the Cardiograph. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33
PageWriter Trim II and III Orders and Archive
About Orders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1About the Archive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1Using the Order Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2Entering New Orders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4Deleting an Order. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4Editing an Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5Loading Orders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5Using the Archive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Saving Auto ECGs to the Archive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6Opening the Archive Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7Transferring Auto ECGs to a TraceMasterVue ECG Management System . . . . . . . . . . . . . 4-9Viewing and Printing Auto ECGs in the Archive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10Faxing Auto ECGs in the Archive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11Editing Patient ID Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13Exporting 12-lead Reports in XML Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14Printing a List of Auto ECGs in the Archive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14Searching a TraceMasterVue Remote Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
Searching a Remote Site with the Wildcard Character . . . . . . . . . . . . . . . . . . . . . . . . 4-15Deleting Auto ECGs from the Archive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16
Reading the Printed ECG Report
Interpretive, Reason, and Severity Statements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
PageWriter Trim Cardiograph Instructions for Use Contents-5
![Page 8: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/8.jpg)
Severity Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3Basic Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4Patient ID Clinical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5Patient ID Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
Additional Patient ID Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7Institution Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-7Configurable Clinical Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-8ECG Order Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-9Physician Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-10Report Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-10Calibration Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-11Time Separator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-13Pacing Detection Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-13Algorithm Version Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-16Speed and Sensitivity Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-16Device Identification Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1712-Lead ECG Report Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-18Extended Measurements Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-25Rhythm Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-25Disclose Report. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-28
Troubleshooting
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1Troubleshooting Topics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1
Archive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2Barcode Reader. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-6Battery and AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-6LAN and Modem Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-8Leads Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-9Magnetic Card Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-10Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-10Signal Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-14System Freeze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-16
Resetting the Cardiograph . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-17
Cardiograph Care and Maintenance
Cardiograph Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1Approved Cleaning Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1
PIM, Patient Data Cable and Lead Wire Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2Reusable Electrode Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2Changing the Date and Time on the PageWriter Trim I . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-3Changing the Date and Time on the PageWriter Trim II and III . . . . . . . . . . . . . . . . . . . . . . .7-3
Contents-6 PageWriter Trim Cardiograph Instructions for Use
![Page 9: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/9.jpg)
Printer Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4Tips for changing printer paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Battery Maintenance and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7Battery Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8Replacing the AC Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9Replacing the Lead Wires on the PIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10Maintenance Tests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
PIM Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13Barcode Reader Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13Magnetic Card Reader Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14Printer Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14Network Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17
Important Patient and Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-18Supplies and Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21
Ordering Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21PageWriter Trim Cardiograph Supply Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22
Patient Interface Module (PIM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22Replacement Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22Complete Lead Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22Replacement Lead Sets and Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22Electrodes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22
Cardiograph Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-23Optional Cardiograph Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-23Printer Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-23Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-23
Contacting a Philips Response Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-24North America Response Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-24South America Response Centers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-25Europe Response Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-25Asia Response Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-26Africa and Middle East . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-27
Suppressed Borderline Interpretive Statements
Level 1 Suppressed Statements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1Level 2 Suppressed Statements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
Specifications
Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1ECG Acquisition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1Patient Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1Cardiograph Cart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
PageWriter Trim Cardiograph Instructions for Use Contents-7
![Page 10: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/10.jpg)
Signal Processing/Acquisition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2Sampling Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
Auto Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2Rhythm Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
Printer Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2Report Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2Battery Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3
Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3Recharge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3
Network Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3FAX Capability (optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3Modem (optional for USA and Canada) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3Barcode Reader (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3Magnetic Card Reader (optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3ECG Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3ECG File Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3Power and Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4
Line Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4Environmental Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4Environmental Storage Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4Cardiograph Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4Cardiograph Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4Cardiograph Shipping Container Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4Cardiograph Shipping Container Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4Cardiograph Cart Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4Cardiograph Cart Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4Cardiograph Cart Shipping Container Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5Cardiograph Cart Container Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5
Safety and Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5Electromagnetic Compatibility (EMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5
Reducing Electromagnetic Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5
Assembling the Patient Cable Arm
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2
Contents-8 PageWriter Trim Cardiograph Instructions for Use
![Page 11: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/11.jpg)
Safety and Regulatory Symbols Marked on the Cardiograph About the Instructions for Use
1About the PageWriter Trim Cardiograph
About the Instructions for UseThis PageWriter Trim Cardiograph Instructions for Use is intended to assist users in the safe and effective use of the product.
Before attempting to operate this product, read this Instructions for Use, and note and strictly observe all Warning and Cautions as described in this document.
Pay special attention to all of the safety information provided in the Safety Summary section. For more information, see page i-i.
WARNING Warning statements describe conditions or actions that may result in a potentially serious outcome, adverse event, or a safety hazard. Failure to follow a Warning may result in death or serious injury to the user or to the patient.
CAUTION Caution statements describe when special care is necessary for the safe and effective use of the product. Failure to follow a caution may result in minor to moderate personal injury or damage to the product or other property, a remote risk of more serious injury, or may cause environmental pollution.
NOTE Notes contain additional important information about a topic.
TIP A Tip contains suggested information on using a particular feature.
Menu items and button names appear in bold no-serif font. Example: Touch the Config button.
Safety Summary
Safety and Regulatory Symbols Marked on the Cardiograph
Symbol Name Description
Attention See the PageWriter Trim Instructions for Use for information.
Type CF ECG physio isolation is type CF, defibrillator proof. Electrical leakage current is suitable for all patient applications including direct cardiac application.
On/Standby or On/Off
Pressing the button with this symbol on it turns on the cardiograph, turns off the cardiograph, or puts the cardiograph into Standby (power saving mode).
PageWriter Trim Cardiograph Instructions for Use i-i
![Page 12: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/12.jpg)
Safety Summary Safety Symbols Marked on the Cardiograph Packaging
Electrostatic Discharge
Do not touch exposed pins. Touching exposed pins can cause electrostatic discharge that can damage the cardiograph.
Equipotential grounding post
Equipotential grounding post used for establishing common ground between instruments.
Fuse Cardiograph contains a 1.5 amp (250V) time-delay fuse.
Input The connector near this symbol receives an incoming signal.
Serial Number The number next to this symbol is the serial number of the cardiograph.
Product model number
The number next to this symbol is the product model number of the cardiograph.
Entry of liquids The PIM (Patient Interface Module) is protected against splashing water. Water splashed against the PIM from any direction shall have no harmful effect.
AC power indicator light
When lit, indicates that AC power is on. The battery is charging when inserted into the cardiograph.
Disposal Information
Dispose of in accordance with the requirements of your country.
Safety Symbols Marked on the Cardiograph Packaging
Symbol Description
Keep dry.
Ambient temperature range of 0 oC (32o.F) to 50 oC (122o F) (non-condensing) for transport and storage.
Safety and Regulatory Symbols Marked on the Cardiograph
i-ii PageWriter Trim Cardiograph Instructions for Use
![Page 13: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/13.jpg)
Safety Symbols Marked on the Cardiograph Packaging Safety Summary
Atmospheric pressure range of 466 hPa to 1014 hPa for transport and storage.
Relative humidity range of 15% to 90% (non-condensing) for transport and storage.
Move and store packaging this end up.
Fragile.
Sealed lead acid battery. Do not dispose of in trash. Follow local regulations for disposing of as small chemical waste.
Safety Symbols Marked on the Cardiograph Packaging
PageWriter Trim Cardiograph Instructions for Use i-iii
![Page 14: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/14.jpg)
Important Patient and Safety Information Safety Symbols Marked on the Cardiograph Packaging
Important Patient and Safety InformationThe PageWriter Trim cardiograph isolates all connections to the patient from electrical ground and all other conductive circuits in the cardiograph. This reduces the possibility of hazardous currents passing from the cardiograph through the patient’s heart to ground, and from other equipment connected to the patient passing through the leads into the cardiograph to ground.
WARNING Failure to follow these warnings could affect both patient and operator safety.
When operating the cardiograph on AC power, ensure that the cardiograph and all other electrical equipment connected to or near the patient are effectively grounded.
Use only grounded power cords (three-wire power cords with grounded plugs) and grounded electrical outlets. Never adapt a grounded plug to fit an ungrounded outlet by removing the ground prong. Use the equipotential post when redundant earth ground is necessary according to IEC 60601-1-1.
If a safe ground connection is not ensured, operate the cardiograph on battery power only.
The use of equipment that applies high frequency voltages to the patient (including electrosurgical equipment and some respiration transducers) is not supported and may produce undesired results. Disconnect the patient data cable from the cardiograph, or detach the leads from the patient prior to performing any procedure that uses high frequency surgical equipment.
Do not perform ST analysis on the R/T ECG screen display or on Rhythm reports when the 0.5 Hz Baseline Wander filter is applied.
If abnormal ECG data appears on the printed report, and the abnormal data does not have a physiological origin, perform the printer diagnostic test to assess printer performance.
When printing a Rhythm report, there may be a slight delay before the Rhythm report begins to print on the cardiograph. Rhythm printing is not completed in real-time.
Pace pulse tick marks will not print on an Auto ECG that uses simultaneous acquisition.
WARNING Do not touch accessible connector pins and the patient simultaneously.
Electrical shock hazard. Keep cardiograph, Patient Interface Module (PIM) and all cardiograph accessories away from liquids. Do not immerse cardiograph, PIM, or other accessories in any liquids.
Periodically inspect the patient data cable, lead wires, and AC power cord for any worn or cracked insulation to ensure that no inner conductive material is exposed. Discard worn accessories and replace them only with Philips Medical Systems accessories (see page 1-35).
Keep the patient data cable away from power cords and any other electrical equipment. Failure to do so can result in AC power line frequency interference on the ECG trace.
i-iv PageWriter Trim Cardiograph Instructions for Use
![Page 15: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/15.jpg)
Safety Symbols Marked on the Cardiograph Packaging Important Patient and Safety Information
The Philips Medical Systems patient data cable (supplied with cardiograph) is an integral part of the cardiograph safety features. Use of any other patient data cable may compromise defibrillation protection, degrade cardiograph performance, and may result in distorted ECG data.
Only qualified personnel may service the cardiograph or may open the cardiograph housing to access internal cardiograph components. Do not open any covers on the cardiograph. There are no internal cardiograph components that are serviced by the operator.
Do not use this cardiograph near flammable anesthetics. It is not intended for use in explosive environments or in operating rooms.
Do not touch the patient, the patient data cable, any unused patient leads, or the cardiograph during defibrillation. Death or injury may occur from the electrical shock delivered by the defibrillator.
Always use electrode gel with reusable electrodes during defibrillation as ECG recovery will be greater than 10 seconds. Philips Medical Systems recommends the use of disposable electrodes at all times.
Ensure that the electrodes or lead wires do not come in contact with any other conductive materials (including earth-grounded materials) especially when connecting or disconnecting electrodes to or from a patient.
Connecting multiple medical electrical equipment to the same patient may pose a safety hazard due to the summation of leakage currents. Any combination of instruments should be evaluated by local safety personnel before being put into service.
Portable medical equipment such as X-rays and MRI may produce electromagnetic interference that produces noise in the ECG signal. Move the cardiograph away from these potential sources of electromagnetic interference.
Do not pull on the paper while an ECG report is being printed. This can cause distortion of the waveform and can lead to potential misdiagnosis.
Only use the Philips Medical Systems AC power cord supplied with the cardiograph. Periodically inspect the AC power cord and AC power connector (rear of cardiograph, see page 1-9) to ensure that both are in a safe and operable condition. If the AC power cord or AC power connector is not in a safe or operable condition, operate the cardiograph on battery power and contact Philips Medical Systems for service.
The cardiograph has been safety tested with the recommended accessories, peripherals, and leads, and no hazard was found when the cardiograph is operated with cardiac pacemakers or other stimulators.
Do not connect any equipment or accessories to the cardiograph that are not manufactured or approved by Philips Medical Systems or that are not IEC 60601-1 approved. The operation or use of non-approved equipment or accessories with the cardiograph is not tested or supported, and cardiograph operation and safety are not guaranteed.
PageWriter Trim Cardiograph Instructions for Use i-v
![Page 16: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/16.jpg)
Important Patient and Safety Information Safety Symbols Marked on the Cardiograph Packaging
The list of cables and other accessories with which Philips claims compliance with the emissions and immunity requirements of IEC standard 60601-1-2 are listed in “Supplies and Ordering Information” on page 1-35.
WARNING When using additional peripheral equipment powered from an electrical source other than the cardiograph, the combination is considered to be a medical system. It is the responsibility of the operator to comply with IEC 60601-1-1 and test the medical system according to the requirements. For additional information contact Philips Medical Systems.
WARNING Do not use non-medical peripherals within 1.83 meters or 6 feet of a patient unless the non-medical peripherals receive power from the cardiograph or from an isolation transformer that meets medical safety standards.
Only install Philips Medical Systems software on the cardiograph. The installation or use of software not approved by Philips Medical Systems is strictly prohibited and cardiograph safety and performance are not guaranteed.
Only use Philips Medical Systems replacement parts and supplies with the cardiograph. The use of non-approved replacement parts and supplies with the cardiograph is strictly prohibited. Cardiograph safety and performance are not guaranteed when non-approved replacement parts and supplies are used with the cardiograph.
Manual measurements of ECG intervals and magnitudes should be performed on printed ECG reports only. Do not make manual measurements of ECG intervals and magnitudes on the R/T ECG display since these ECG representations are scaled.
Only use patient electrodes that are approved by Philips Medical Systems. The use of non-approved patient electrodes may degrade cardiograph performance.
The Philips Medical Systems warranty is applicable only if you use Philips Medical Systems approved accessories and replacement parts. See “Supplies and Ordering Information” on page 1-35 for more information.
Before using the Patient Cable Arm with the cardiograph cart, properly install the counter weight on the cardiograph base.
Only use the shielded LAN cable provided with the PageWriter Trim cardiograph, Philips Part Number 989803138021. Do not use any other LAN cables with the PageWriter Trim cardiograph. Use of unapproved LAN cables may result in radiated emissions that exceed the limit specified by CISPR11 Class B.
The combined maximum weight that can be placed on the cardiograph cart shelf and the top surface of the cart cannot exceed 20 kg (44 lbs). Do not place more than the specified weight on the cardiograph top surface and shelf.
Do not connect any device to the RS-232 port on the rear of the cardiograph when the patient data cable is connected to a patient.
There are no cardiograph parts that can be sterilized.
i-vi PageWriter Trim Cardiograph Instructions for Use
![Page 17: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/17.jpg)
Intended Use The PageWriter Trim Cardiograph
The cardiograph is not intended for direct, or invasive cardiac monitoring purposes.
Excessive, repetitive use of the cardiograph keyboard and the cardiograph Trim Knob may result in a risk of developing carpal tunnel syndrome.
Ensure that the patient data cable is tucked away from the cardiograph cart wheels when transporting the cardiograph. Ensure that the patient data cable does not present a hazard when pushing the cardiograph cart.
For information on the standard IEC 60601-2-51, please go to the Philips InCenter web site (incenter.medical.philips.com). For information on using the Philips InCenter web site, see page 1-4.
The PageWriter Trim CardiographThis Philips product is intended to be used and operated only in accordance with the safety procedures and operating instructions provided in this Instructions for Use, and for the purposes for which it was designed. The purposes for which the product is intended is provided below. However, nothing stated in this Instructions for Use reduces the responsibility of the user for sound clinical judgment and best clinical procedures.
Intended UseThe intended use of the cardiograph is to acquire multi-channel ECG signals from adult and pediatric patients from body surface ECG electrodes and to record, display, analyze, and store these ECG signals for review by the user. The cardiograph is to be used in healthcare facilities by trained healthcare professionals. Analysis of the ECG signals is accomplished with algorithms that provide measurements, data presentations, graphical presentations, and interpretations for review by the user.
The interpreted ECG with measurements and interpretive statements is offered to the clinician on an advisory basis only. It is to be used in conjunction with the clinician's knowledge of the patient, the results of the physical examination, the ECG tracings, and other clinical findings. A qualified physician is asked to overread and validate (or change) the computer-generated ECG interpretation.
Indications for UseThe cardiograph is to be used where the clinician decides to evaluate the electrocardiogram of adult and pediatric patients as part of decisions regarding possible diagnosis, potential treatment, effectiveness of treatment, or to rule out causes for symptoms.
The Philips 12-Lead Algorithm The PageWriter Trim cardiograph software uses the Philips 12-Lead Algorithm. The algorithm in the software analyzes the morphology and rhythm on each of the 12 leads and summarizes the results. The set of summarized measurements is then analyzed by the clinically-proven ECG Analysis Program.
PageWriter Trim Cardiograph Instructions for Use i-vii
![Page 18: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/18.jpg)
The Philips 12-Lead Algorithm Intended Use
12-lead Reports may include or exclude ECG measurements, reasons, or analysis statements.
Intended UseThe intended use of the Philips 12-Lead Algorithm is to analyze multi-channel ECG signals from adult and pediatric patients with algorithms that provide measurements, data presentations, graphical presentations, and interpretations for review by the user.
The interpreted ECG with measurements and interpretive statements is offered to the clinician on an advisory basis only. It is to be used in conjunction with the clinician's knowledge of the patient, the results of the physical examination, the ECG tracings, and other clinical findings. A qualified physician is asked to overread and validate (or change) the computer-generated ECG interpretation.
Indications for UseThe Philips 12-Lead Algorithm is to be used where the clinician decides to evaluate the electrocardiogram of adult and pediatric patients as part of decisions regarding possible diagnosis, potential treatment, effectiveness of treatment, or to rule out causes for symptoms.
i-viii PageWriter Trim Cardiograph Instructions for Use
![Page 19: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/19.jpg)
1
1Getting Started
Welcome to the PageWriter Trim cardiograph! With its fast and simple operation, clearly labeled PIM and lead wires, and convenient cart, it is the ideal cardiograph for processing large volumes of ECGs quickly and easily.
The PageWriter Trim supports multiple ECG acquisition modes, display settings, and report formats. Signal quality indicators provide instant feedback to the user to help ensure a quality ECG each and every time.
This PageWriter Trim Cardiograph Instructions for Use includes an overview of the cardiograph and all of its components, setup and assembly instructions, care and maintenance information, and information on troubleshooting. It is intended to be used with the other materials included in the PageWriter Trim Cardiograph Learning Kit.
NOTE Read and complete the materials included in the PageWriter Trim Cardiograph Learning Kit before using the cardiograph. Pay close attention to all warnings and cautions.
1-1
![Page 20: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/20.jpg)
Getting Started PageWriter Trim Cardiograph Learning Kit
PageWriter Trim Cardiograph Learning KitPhilips Medical Systems provides detailed instructional and reference materials in the PageWriter Trim Learning Kit
The PageWriter Trim Learning Kit contains the Getting Started Guide, a Quick Help Card, and the User Documentation and Interactive Training CDs. Figure 1-1 The PageWriter Trim Cardiograph Learning Kit
About the PageWriter Trim Learning Kit Getting Started Guide (A)This guide includes important information that must be read before operating the cardiograph. It includes an overview of cardiograph features and functions, assembly and setup instructions, how to configure the cardiograph, and how to order supplies.
Quick Help Card (B) This card provides quick reference information about basic cardiograph features, lead placement, and signal quality indicators. It is also provided as a PDF file on the PageWriter Trim User Documentation CD.
PageWriter Trim User Documentation CD (C)The User Documentation CD includes the following files: – Philips 12-Lead Algorithm Physician’s Guide
This guide describes the Philips 12-Lead Algorithm, and lists all of the interpretive statements included in the 0A criteria.
– PageWriter Trim I, II, III Instructions for UseThis instructions for use includes complete information on all aspects of using and maintaining the cardiograph.
A
B
C
D
1-2 PageWriter Trim Cardiograph Instructions for Use
![Page 21: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/21.jpg)
Getting Started Philips 12-Lead ECG XML Information and Tools
– PageWriter Trim I, II, III Quick Help Card A PDF version of the fold-out Quick Help Card provided in the Learning Kit.
– PageWriter Trim Cart Assembly InstructionsThis instruction sheet describes how to assemble the optional PageWriter Trim cart.
– PageWriter Trim Wireless LAN Installation InstructionsThis instruction sheet describes how to install and configure the wireless LAN option for the cardiograph.
To view user documentation:
1 Insert the CD into a PC CD-ROM drive. The CD only works on PCs with a Windows operating system.The user documentation CD main menu opens automatically. Click on a blue button or the file name to view the file.
2 If the menu does not automatically appear, open the CD in Windows Explorer.
3 Double-click the file menu.pdf. The main menu appears. Any of the files on the CD may be printed or saved to a PC hard drive.
NOTE If files from the CD are saved to a PC hard drive, Acrobat Reader 7.0 will need to be installed on the PC in order to view the files. For a free install go to: www.adobe.com.
PageWriter Trim Cardiograph Interactive Training Program CD (D)The interactive training CD contains a computer-based training program that describes how to properly record an ECG and how to operate the cardiograph. Use this program to train the entire ECG staff in the proper operation of the cardiograph.
To run the interactive training program:
1 Insert the CD into a CD-ROM drive. The CD only works on PCs with a Windows operating system.The interactive training program starts automatically.
2 If the interactive training program does not automatically start, open the CD in Windows Explorer.
3 Double-click the file pwtrim.exe. The interactive training program file may be saved to any PC hard drive and does not require any special software to operate.
Philips 12-Lead ECG XML Information and ToolsThe PageWriter Trim cardiograph exports 12-lead ECG data in XML (Extensible Markup Language) format. The XML schema for the Philips 12-lead ECG files, and a complementary suite of XML utilities and tools are available for download from the Philips InCenter web site. An XML Utility Suite Instructions for Use is also available for download. This Instructions for Use describes how to install and configure the XML utilities. Check the InCenter site regularly for documentation updates, and for further information and updates to the XML Utility Suite.
PageWriter Trim Cardiograph Instructions for Use 1-3
![Page 22: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/22.jpg)
Getting Started Using the Philips InCenter Site
Using the Philips InCenter SiteThe Philips InCenter web site provides frequent updates to all Philips Cardiac Systems product documentation and product software, including the PageWriter Trim cardiographs.
The Philips InCenter web site requires an active registration and password. To register, go to the InCenter web site at: incenter.medical.philips.com and click on the Click here for access to software updates and documentation for cardiology products link located on the right side of the page. The Cardiac Systems InCenter Registration page appears. Complete all of the information fields on the page to receive a login and password for the InCenter site.
Registration for the InCenter web site requires the serial number(s) for all PageWriter Trim cardiographs in active use at your facility. The serial number is located on the rear panel of the cardiograph (directly underneath the battery door), next to the SN text.Figure 1-2 Serial Number on Product Identification Label
About Adobe Acrobat VersionsAdobe Acrobat Reader version 7.0 must be installed on the PC that is used to access the Philips InCenter web site. Previous versions of Acrobat Reader are not compatible, and attempting to access InCenter with a previous version of Acrobat Reader will result in error messages when opening documents. Uninstall all previous versions of Acrobat Reader, and then proceed for a free install of Acrobat Reader 7.0 at: www.adobe.com.
Adobe Acrobat Professional version 7.0 is also not compatible with the Philips InCenter site, and error messages will appear when opening documents with this version of Acrobat software. Acrobat Reader 7.0 must be installed in addition to Acrobat Professional.
Follow the procedure below when using the Philips InCenter site.
To access documents on the InCenter site:
1 Exit Acrobat Professional (if open).
2 Start Acrobat Reader 7.0.
3 Open Internet Explorer, and go to the Philips InCenter site. Keep Acrobat Reader 7.0 open the entire time while accessing the InCenter site.
1-4 PageWriter Trim Cardiograph Instructions for Use
![Page 23: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/23.jpg)
Getting Started Attaching the Cardiograph to the Cart
Attaching the Cardiograph to the CartThe PageWriter Trim cardiograph is available with an optional cart that includes a storage shelf and a holder for the PIM (Patient Interface Module).
For information on assembling the PageWriter Trim cart, see the PageWriter Trim Cart Assembly Instructions available as a PDF file on the User Documentation CD. This file may also be downloaded from the Philips InCenter web site (incenter.medical.philips.com).
CAUTION Follow the procedure below to ensure that the cardiograph is securely fastened to the cart before use.
To attach the cardiograph to the cart:
1 Align the front feet of the cardiograph with the front locking holes on the cart. Align the rear feet of the cardiograph with the rear screw holes on the cart. Lower the cardiograph onto the cart.
2 Slide the cardiograph back to lock the front and rear feet into place. Insert the screws through the bottom of the cart and through the screw holes. Tighten the screws with a Phillips head screwdriver.
PageWriter Trim Cardiograph Instructions for Use 1-5
![Page 24: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/24.jpg)
Getting Started PageWriter Trim I Cardiograph Parts
PageWriter Trim I Cardiograph PartsThe following sections show front, side, and rear views of the PageWriter Trim I cardiograph. Figure 1-3 PageWriter Trim I Cardiograph and Cart (Front View)
CAUTION Always lock the wheel brake (F) when the cart is not in use. Press down on the wheel brake to set or to release the wheel brake.
A Patient Interface Module (PIM) E PIM leadsB Printer paper/report storage slot F Wheel brakeC Storage shelf G Control panel D AC power cord H Printer paper drawer
A
B
D
E
F
H
G
C
1-6 PageWriter Trim Cardiograph Instructions for Use
![Page 25: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/25.jpg)
Getting Started PageWriter Trim I Cardiograph Parts
Figure 1-4 PageWriter Trim I Cardiograph (Rear View)
WARNING Do not connect a LAN cable connector to the PIM connector. Do not plug a telephone connector into the PIM connector.
I AC power cord connector L Battery door
J Equipotential grounding post M PIM connector
K Fuse door N Serial connector (not supported)
I
KN
M L
J
PageWriter Trim Cardiograph Instructions for Use 1-7
![Page 26: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/26.jpg)
Getting Started PageWriter Trim II and III Cardiograph Parts
PageWriter Trim II and III Cardiograph PartsThe following sections show front, side, and rear views of the PageWriter Trim II and III cardiographs. Figure 1-5 PageWriter Trim II and III Cardiograph and Cart
(Front View)
CAUTION Always lock the wheel brake (F) when the cart is not in use. Press down on the wheel brake to set or to release the wheel brake.
A Patient Interface Module (PIM) F Wheel brakeB Printer paper/report storage slot G Control panel C Storage shelf H KeyboardD AC power cord I Trim knobE PIM leads J Printer paper drawer
A
B
D
E
F
H
I
J
G
C
1-8 PageWriter Trim Cardiograph Instructions for Use
![Page 27: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/27.jpg)
Getting Started PageWriter Trim II and III Token Label
Figure 1-6 PageWriter Trim II and III Cardiograph (Rear View)
WARNING Do not connect the LAN cable connector into the PIM connector. Do not plug a telephone connector into the PIM connector.
PageWriter Trim II and III Token Label A token label is affixed to the interior of the cardiograph, above the paper tray. To locate the token label, remove the paper tray from the cardiograph. The label is located on the far right side of the metal housing. The number on the token label is referred to when the cardiograph is serviced, software is installed, or when an optional feature is added to the cardiograph. Ensure that the most current token label is affixed to the cardiograph. For more information on the token label, contact the nearest Philips Response Center, see page 1-38 for more information.Figure 1-7 PageWriter Trim Cardiograph Token Label
K Reset button Q Battery door
L PC card eject button R PIM connector
M PC card slot S SmartCard reader or USB memory stick connector
N AC power connector T Barcode reader or magnetic card reader connector
O Equipotential grounding post U Serial connector (not supported)
P Fuse door
N O
Q
M
P
RS
KL
T
U
PageWriter Trim Cardiograph Instructions for Use 1-9
![Page 28: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/28.jpg)
Getting Started Patient Interface Module (PIM)
Figure 1-8 Location of Token Label on Cardiograph
Patient Interface Module (PIM)The Patient Interface Module (PIM) is a hand-held device that connects to the cardiograph. The lead wires on the PIM attach to the electrodes placed on the patient. The exterior of the PIM is labeled and color-coded for quick and easy lead identification.
1-10 PageWriter Trim Cardiograph Instructions for Use
![Page 29: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/29.jpg)
Getting Started Patient Interface Module (PIM)
Figure 1-9 Patient Interface Module
Inserting the Lead Wires into the PIMThe exterior of the PIM is color-coded for quick and easy lead identification. The lead wires that are included with the cardiograph must be inserted into the correct lead wire connector on the PIM.
A Lead wire labeling C Limb lead wires
B Patient data cable D Precordial (chest) lead wires
A
CD
B
PageWriter Trim Cardiograph Instructions for Use 1-11
![Page 30: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/30.jpg)
Getting Started Patient Interface Module (PIM)
Figure 1-10 PIM connector and lead wire labeling
To insert the lead wires into the PIM:
1 Locate the lead wires in the cardiograph packaging.
2 Match the lead wire to the correct lead wire connector on the PIM.
3 Insert each lead wire into the correct lead wire connector on the PIM.
4 Push down on the lead wire to ensure that there is no gap between the lead wire and the connector.
Connecting the PIM to the CardiographConnect the patient data cable on the PIM to the PIM connector port ( ) on the rear panel of the cardiograph.
A Lead wire connector C Lead wire labeling
B Lead wire
A
B
C
1-12 PageWriter Trim Cardiograph Instructions for Use
![Page 31: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/31.jpg)
Getting Started Patient Interface Module (PIM)
To connect the PIM to the cardiograph:
Connect the patient data cable to the PIM connector port on the rear of the cardiograph.
WARNING To ensure safety and prevent damage to the system, only connect the patient data cable to the PIM connector port on the rear of the cardiograph.
Placing the PIM in the HolderPlace the PIM in the holder when not in use. The PIM holder is located on the rear of the optional cardiograph cart. Ensure that the lead wires are facing down. Figure 1-11 Inserting the PIM into the holder
CAUTION Ensure that the PIM patient data cable and lead wires do not drag on the ground or become tangled in the cart wheels.
PageWriter Trim Cardiograph Instructions for Use 1-13
![Page 32: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/32.jpg)
Getting Started Installing the Battery
Installing the BatteryThe cardiograph is shipped with one removable battery. Install the battery before plugging the cardiograph into AC power. Figure 1-12 Installing the Battery
To install the battery:
1 Open the battery door on the rear of the cardiograph. Push the recessed tab in and pull it down to open the battery door.
2 Insert the battery into the compartment with the connector facing down and the pull tab facing out.
3 Push in the pull tab to lock it.
4 Reattach and close the battery door.
5 Attach the AC power cord to the rear of the cardiograph.
1-14 PageWriter Trim Cardiograph Instructions for Use
![Page 33: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/33.jpg)
Getting Started Charging the Battery
6 Plug the AC power cord into a grounded electrical outlet. Check that the green AC power indicator light is on (front of cardiograph).
7 Charge the battery for at least twenty-four hours before mobile use.
Charging the BatteryAfter the battery is installed in the cardiograph, it must be charged for at least twenty-four hours prior to use.
With the battery fully charged, the cardiograph will print up to thirty Auto ECGs or provide thirty minutes of continuous Rhythm printing.
The green AC indicator light on the front of the cardiograph indicates that the battery is charging when the cardiograph is plugged into AC power. Plug the cardiograph into AC power whenever possible.
To disconnect the cardiograph from AC power, unplug the AC power cord from the grounded electrical outlet.
PageWriter Trim II and III, Battery Charging IndicatorOn the PageWriter Trim II and III, a lightening bolt icon ( ) appears on the Battery Level Indicator on the Status Bar to indicate that the cardiograph is plugged into AC power and the battery is charging. Check the Battery Power Indicator on the Status Bar to ensure that the battery is fully charged. The cardiograph can operate on AC power while the battery is charging, but the battery will charge at a slower rate.Figure 1-13 PageWriter Trim II and III Battery Level Indicator
A Battery level indicator
Table 1-1 PageWriter Trim II and III Battery Level Indicator
Battery Level Status Indicator
Fully Charged Battery
75% power capacity
50% power capacity
V2 94 FW 60~0.5-150 Hz P? ID: 12345
NAME: Doe, John
A
PageWriter Trim Cardiograph Instructions for Use 1-15
![Page 34: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/34.jpg)
Getting Started Charging the Battery
PageWriter Trim I, Battery Charging IndicatorOn the PageWriter Trim I, the battery icon ( ) flashes on the LCD display when the cardiograph is plugged into AC power and the battery is charging, see “LCD Display” on page 1-30.The battery level indicator displays the following battery icon ( ) when the battery is fully charged. The cardiograph can operate on AC power while the battery is charging, but the battery will charge at a slower rate.
Low Battery Power
Low Battery Alert; alternate icons flashing, cardiograph beeps until the unit is plugged into AC power
No or Dead Battery
Battery is charging (moving bars)
Table 1-2 PageWriter Trim I Battery Level Indicator
Battery Level Status Indicator
Fully Charged Battery
50% power capacity
Low Battery Power
Low Battery Alert
Table 1-1 PageWriter Trim II and III Battery Level Indicator (continued)
Battery Level Status Indicator
1-16 PageWriter Trim Cardiograph Instructions for Use
![Page 35: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/35.jpg)
Getting Started Powering on the Cardiograph
Powering on the CardiographEnsure that the battery is inserted into the cardiograph before turning on the AC power to the cardiograph. See “Installing the Battery” on page 1-14. The cardiograph is powered by the battery or by AC power. The battery must be inserted into the cardiograph at all times. The cardiograph printer will not function if the battery is not installed.Figure 1-14 The On/Standby Button
To turn on the cardiograph:
1 Plug the AC power cord into the AC power connector on the rear of the cardiograph.
2 Plug the AC power cord into a grounded electrical outlet with appropriate electrical ratings. The AC power indicator light on the front panel of the cardiograph illuminates when the cardiograph is plugged into AC power.
3 Press the On/Standby or On/Off button on the front of the cardiograph.
No or Dead Battery
Battery is charging
Table 1-2 PageWriter Trim I Battery Level Indicator (continued)
Battery Level Status Indicator
A On/Standby button (PageWriter Trim II/III) or On/Off button (PageWriter Trim I)
B AC Power Indicator Light
A
B
A
B
PageWriter Trim Cardiograph Instructions for Use 1-17
![Page 36: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/36.jpg)
Getting Started Powering on the Cardiograph
Using the On/Standby Button
PageWriter Trim II and III only
The On/Standby button is used to put the cardiograph into Standby and to shut down the cardiograph.
TIP There are configurable features on the cardiograph that can be used to help prolong battery life (see page 2-25). Proper battery care and maintenance (including frequent and full charging of the battery) will also help to prolong battery life.
TIP Plug the cardiograph into AC power whenever possible to help prolong battery life.
To put the cardiograph into Standby:
Press the On/Standby button. A message appears that the cardiograph is entering Standby. The green Standby indicator light (front of cardiograph) illuminates. The battery charges when the cardiograph is plugged into AC power.
NOTE The cardiograph cannot be put into Standby if the Patient ID screen is open or if the cardiograph is printing an ECG.
Table 1-3 Standby and Shut Down Setting Description
Setting Description
Standby Use between brief periods of inactivity to save battery power
The cardiograph is in a sleep mode
The display screen is black
Patient ID information is not saved when the cardiograph is put into Standby
Temporary report settings are saved when the cardiograph is put into Standby
The battery charges when the cardiograph is plugged into AC power
The green Standby indicator light (front of cardiograph) is lit
Press any key on the keyboard to return the cardiograph to active use
The cardiograph returns to the previously viewed screen when taken out of Standby
Shut Down Use for extended periods of cardiograph inactivity
The cardiograph is shut down
The display screen is black
The battery charges when the cardiograph is plugged into AC power
Press the On/Standby button to restart the cardiograph
1-18 PageWriter Trim Cardiograph Instructions for Use
![Page 37: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/37.jpg)
Getting Started Loading Printer Paper
To exit Standby:
Press the On/Standby button. The splash screen appears. The R/T (real-time) ECG screen appears.
To shut down the cardiograph:
Press and hold the On/Standby button for three seconds then release it. A message appears that the cardiograph is shutting down.
To turn on the cardiograph:
Press the On/Standby button. The cardiograph displays a series of startup screens and then the R/T (real-time) ECG screen displays.
Loading Printer PaperReplace the printer paper when a red stripe appears on the printed ECG report. Only use Philips Medical Systems replacement printer paper. For part number and ordering information, see page 1-35.
Tips for loading printer paperAlways load less than 100 sheets of printer paper into the paper tray
Ensure that the entire first page of the new paper roll is fully draped over the roller before closing the printer door
PageWriter Trim II and III:
Ensure that the paper size configured for the cardiograph is the same size paper being loaded into the paper drawer (see page 2-24)
To load paper into the printer:
1 Open the paper drawer on the front of the cardiograph and lift up the bar.
PageWriter Trim Cardiograph Instructions for Use 1-19
![Page 38: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/38.jpg)
Getting Started Loading Printer Paper
2 Insert a new pack of printer paper as shown. Ensure that no more than 100 sheets are being inserted into the paper tray.
3 Ensure that the paper sensor hole (A) is positioned as shown.
4 Drape the entire first sheet over the roller. Ensure that the perforated edge of the paper aligns with the edge of the paper drawer. Lower the bar onto the paper and close the drawer.
1-20 PageWriter Trim Cardiograph Instructions for Use
![Page 39: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/39.jpg)
Getting Started Using the PC Card Slot
5 Tear off the first sheet as shown.
Using the PC Card SlotPageWriter Trim II and III only
The PC card slot (rear of cardiograph) is used with the optional PC card, wireless LAN card, LAN card, or modem card. All of these are optional accessories available with the cardiograph, and are inserted into the PC card slot. For information on ordering any of these accessories, see “Supplies and Ordering Information” on page 1-35.
Using the PC CardThe PC card contains a 128 MB removable memory card that can be used to transfer ECGs to a TraceMasterVue ECG Management System, or to transfer Orders to the cardiograph. The PC card can store up to 150 ECGs or Orders. The PC card can also be used to store a custom settings file. This custom settings file can be used to transfer custom settings to additional cardiographs, or can be used to restore custom settings on the cardiograph. For information on transferring ECGs or Orders to the cardiograph, see Chapter 4 “PageWriter Trim II and III Orders and Archive” of the PageWriter Trim Instructions for Use on the User Documentation CD, or download the file from the Philips InCenter web site (incenter.medical.philips.com). For information on using the PC card to save custom configuration settings, see page 2-46.
PageWriter Trim Cardiograph Instructions for Use 1-21
![Page 40: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/40.jpg)
Getting Started Using the PC Card Slot
Figure 1-15 The PC card
Using the Wireless LAN Card The PageWriter Trim cardiograph offers a wireless LAN option for the purpose of transferring ECGs to a TraceMasterVue ECG Management System. The wireless LAN connection is compatible with the 802.11b wireless standard. To install and configure the wireless LAN card, see the PageWriter Trim Cardiograph Wireless LAN Installation Instructions available on the User Documentation CD, or download the file from the Philips InCenter web site (incenter.medical.philips.com).
CAUTION Only use wireless LAN cards with the PageWriter Trim cardiograph that have been purchased from Philips Medical Systems. The use of non-approved wireless LAN cards with the PageWriter Trim cardiograph is not tested or supported, and Philips Medical Systems does not guarantee cardiograph operation or wireless LAN connectivity.
Figure 1-16 Wireless LAN Card
A PC card adapter B 128 MB removable memory card
A B
1-22 PageWriter Trim Cardiograph Instructions for Use
![Page 41: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/41.jpg)
Getting Started Using the PC Card Slot
Using the LAN CardThe LAN card is used to transfer ECGs to a TraceMasterVue ECG Management System through a 10/100-Base T Ethernet network connection. The LAN card must be configured before using it with the cardiograph, see page 2-38. For information on transferring ECGs over a network connection to a TraceMasterVue ECG Management System, see Chapter 4 “PageWriter Trim II and III Orders and Archive” of the PageWriter Trim Instructions for Use on the User Documentation CD or download the file from the Philips InCenter web site (incenter.medical.philips.com).
CAUTION Only use the shielded LAN cable provided with the PageWriter Trim cardiograph. Do not use LAN cables with the cardiograph that have not been approved by Philips Medical Systems.
Figure 1-17 Inserting LAN card into PC Card slot
Using the Modem Card The modem card is used to fax ECGs to a remote receiving station, or to transfer ECGs by modem to a TraceMasterVue ECG Management System. The modem card used either as a fax or as a modem must be configured before initial use with the cardiograph, see page 2-34.
For information on faxing ECGs, see page 4-11. For information on transferring ECGs by modem, see page 4-9.Figure 1-18 The Modem Card
PageWriter Trim Cardiograph Instructions for Use 1-23
![Page 42: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/42.jpg)
Getting Started Using the USB Memory Stick
Installing and Removing a PC CardThe PC card, wireless LAN card, LAN card, or modem card are all inserted into the PC card slot.Figure 1-19 Removing the PC card from the cardiograph
To insert or remove a card from the PC card slot:
1 Insert the card into the PC card slot (rear of cardiograph) and gently push it in.
2 Push the PC card eject button to the left of the card slot to eject the card.
3 Pull out the card.
Using the USB Memory Stick PageWriter Trim II and III only
The USB memory stick is an optional accessory that is used to transfer ECGs to a TraceMasterVue ECG Management System, or to transfer Orders to the cardiograph. The USB memory stick can store up to 150 ECGs or Orders.
The memory stick is inserted into the USB connector on the rear of the cardiograph. The memory stick illuminates when it is properly inserted into the USB connector.
NOTE The PageWriter Trim cardiograph only supports the USB memory stick that is shipped with the cardiograph, or that is available for purchase as an optional accessory from Philips Medical Systems. Philips does not guarantee that other USB memory sticks are compatible with the PageWriter Trim cardiograph.
A PC card eject button
A
1-24 PageWriter Trim Cardiograph Instructions for Use
![Page 43: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/43.jpg)
Getting Started Using the Barcode Reader
Figure 1-20 The USB memory stick
Using the Barcode ReaderPageWriter Trim II and III only
The barcode reader is an optional accessory available with the cardiograph. The barcode reader is used to quickly enter Patient ID information by scanning a barcode.
The barcode reader attaches to the barcode reader connector ( ) on the rear panel of the cardiograph. Figure 1-21 The Barcode Reader
PageWriter Trim Cardiograph Instructions for Use 1-25
![Page 44: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/44.jpg)
Getting Started Using the Magnetic Card Reader
Using the Magnetic Card ReaderPageWriter Trim II and III only
The magnetic card reader is an optional accessory available with the cardiograph. The magnetic card reader is used to quickly enter Patient ID information. The Patient ID fields that are entered when a magnetic card is scanned are configurable, see page 2-45.
The magnetic card reader attaches to the magnetic card reader connector ( ) on the rear panel of the cardiograph. For information on ordering the magnetic card reader, see “Supplies and Ordering Information” on page 1-35.Figure 1-22 The Magnetic Card Reader
Using the SmartCard Reader PageWriter Trim II and III only
The SmartCard Reader is an optional accessory available with the cardiograph. The SmartCard Reader is used to quickly enter Patient ID information.
The SmartCard Reader attaches to the USB connector ( ) on the rear panel of the cardiograph. For information on ordering the SmartCard Reader, see “Supplies and Ordering Information” on page 1-35.Figure 1-23 The SmartCard Reader
1-26 PageWriter Trim Cardiograph Instructions for Use
![Page 45: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/45.jpg)
Getting Started Using the Trim Knob
Using the Trim KnobAll models of the PageWriter Trim cardiograph have a Trim Knob that is used to scroll through and select items on any display menu.Figure 1-24 The Trim Knob
To use the Trim Knob:
1 Turn the Trim Knob left or right to scroll through the selections in a menu list.
2 Push the Trim Knob to select an item on the menu.
Navigation TipsPageWriter Trim II and III only
In addition to the Trim Knob, individual keys on the keyboard may be used to navigate on the software screens.
Opening and Closing ScreensTo open and close any screen:
1 Press the Enter key ( ) to close any screen or window and save the information.
2 Press the Esc key ( ) to exit any screen without saving information.
Opening and Closing MenusTo open and close menus:
1 Press the Tab key ( ) to highlight a drop-down menu (in blue).
Figure 1-25 Highlighted drop-down menu
2 Press the space bar ( ) to open the drop-down menu.
PageWriter Trim Cardiograph Instructions for Use 1-27
![Page 46: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/46.jpg)
Getting Started Navigation Tips
Figure 1-26 Opened drop-down menu
3 Press the up or down arrow key ( ) to scroll through the selections in the menu.
4 Press the space bar to select an item and to close the drop-down menu.
Selecting TabsFigure 1-27 Tabs on Patient ID screen
To select a tab:
1 Press and hold the Alt key ( ) on keyboard.
2 Press the letter key in parenthesis on the tab. For example, to select the Rhythm tab, press the Alt key ( ) and the R ( ) key.
Entering Information on a ScreenFigure 1-28 Information fields on the Patient ID screen
To enter information on a screen:
1 Press the Tab key ( ) to go to the next field (white square) on any screen.
2 Press the Tab key and the Shift key ( ) at the same time to go to the previous field (white square) on any screen.
A Tabs
A Field
A
A
1-28 PageWriter Trim Cardiograph Instructions for Use
![Page 47: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/47.jpg)
Getting Started PageWriter Trim I Features
Selecting Check BoxesFigure 1-29 Check box on the Filter screen
To select a check box:
1 Press the Tab key ( ) to highlight the text next to the check box.
2 Press the space bar ( ) to select the check box. A check mark ( ) appears in the box.
3 Press the Enter key ( ) to save the information and to exit the screen.
4 Press the Esc key ( ) to close the screen without saving the information.
PageWriter Trim I FeaturesThe PageWriter Trim I has an LCD display that shows all operating information. The buttons on the main panel of the cardiograph are used for all cardiograph functions. Simply select the buttons on the main panel to use the different functions on the cardiograph.
NOTE Complete the Interactive Training Program on CD before operating the cardiograph. The Interactive Training program includes instructional information on what an ECG is, patient preparation techniques, how to operate the cardiograph, and quality assessment techniques to ensure high-quality ECGs. For information on using the training program, see page 1-3.
A Highlighted check box
A
PageWriter Trim Cardiograph Instructions for Use 1-29
![Page 48: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/48.jpg)
Getting Started PageWriter Trim I Features
Control PanelThe control panel contains all of the main functions on the cardiograph. For more information on any feature, see “The Patient Session" on page 3-1.Figure 1-30 PageWriter Trim I Control Panel
LCD DisplayThe LCD display shows the current settings on the cardiograph.Figure 1-31 PageWriter Trim I LCD Display
A On/off button D Function buttons
B AC power on indicator light E Trim Knob
C LCD Display
Table 1-4 PageWriter Trim I LCD Display
Label Description
A Heart Beat Detector
B Leads Off Indicator
C Signal Quality Indicator
A
B
C
D
E
A C
E
D
FGHI
B
1-30 PageWriter Trim Cardiograph Instructions for Use
![Page 49: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/49.jpg)
Getting Started PageWriter Trim I Features
Function ButtonsAll of the functions on the PageWriter Trim I cardiograph are controlled by the function buttons located on the main panel of the cardiograph. Figure 1-32 Function Buttons on PageWriter Trim I cardiograph
D Battery Level Indicator
E Waveform Speed (mm/sec)
F Waveform Size (mm/mV)
G Filter Settings
H Rhythm Lead
I Report Format
Table 1-5 Function Button description
Label Button Push button to...
A Patient ID Enter Patient ID information (age, gender)
B Auto Take a 3x4, 1R or 6x2 Auto ECG
C Rhythm Print out a continuous Rhythm report (3 or 6 leads) until the Stop button (F) is pressed
D Copy Print out a copy of the last recorded Auto 12-lead ECG
E Page Advance the printer paper to the beginning of the next page
F Stop Stop the printing of a Rhythm report
Return to the previous screen on the LCD display
Table 1-4 PageWriter Trim I LCD Display (continued)
Label Description
A B DC E F
PageWriter Trim Cardiograph Instructions for Use 1-31
![Page 50: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/50.jpg)
Getting Started PageWriter Trim II and III Features
PageWriter Trim II and III FeaturesFor more information on any feature, see “The Patient Session" on page 3-1. Figure 1-33 PageWriter Trim II and III Control Panel
Table 1-6 PageWriter Trim II and III Control Panel
Label Feature Name Description
A On/Standby button
Push to turn on the cardiograph or to put the cardiograph into Standby (power save) when the cardiograph is not in use.Push and hold for three seconds, then release to shut down the cardiograph for extended periods of inactivity.
B Standby indicator When lit, the cardiograph is in Standby (power save) mode and the screen is black.
C AC Power Indicator
When lit, the cardiograph is plugged into AC power and the battery is charging.
D Status Bar Displays current cardiograph settings including: leads off, battery level indicator, patient heart rate, filter settings, pacing detection settings, and patient name and ID.
E Waveform Display
Displays real-time waveforms (waveforms are color-coded to indicate signal quality on the PageWriter Trim III).
Press the up or down arrow key to change the lead format displayed on the screen
Available lead formats include: 6x2, 3x4 1R, 3x4, and 3 lead formats
F Command Toolbar
Buttons contain the major functions of the cardiograph, with the current date and time at the right.
AD
CE
F
G
H
BI
J
K
L
1-32 PageWriter Trim Cardiograph Instructions for Use
![Page 51: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/51.jpg)
Getting Started PageWriter Trim II and III Features
PageWriter Trim II and III Status BarThe Status Bar includes all current operating information for the cardiograph.Figure 1-34 Status Bar
G Patient ID button Press button to enter Patient ID information at the beginning of a patient session.
H Auto button Press button to print out an Auto 12-lead ECG.
Press button twice to print a STAT 12-lead ECG.
I Rhythm button Press button to print out a continuous Rhythm report (up to 12 leads) until the Stop button (L) is touched.
J Copy button Press button to print out a copy of the last recorded Auto 12-lead ECG.
K Page button Press button to advance the printer paper to the beginning of the next page.
L Stop button Press button to stop the printing of a Rhythm report or any other printing function.
Table 1-7 Status Bar Description
Label Feature Name Description
A Leads Off Indicator Displays the name of any loose or disconnected leads or electrodes.
B Heart Rate Indicator Displays the current patient heart rate in beats per minute.
C Battery Level Indicator
Displays the current battery level and if the batteries are charging.
D Filter Settings Displays the filter settings for the current patient session.
E Pacing Detection Settings
Displays the Pacing Detection Setting used for the current patient session.
F Patient Name and ID
Displays the patient name and ID for the current patient session.
Table 1-6 PageWriter Trim II and III Control Panel (continued)
Label Feature Name Description
A DC EB
RL 60~0.15 - 150 Hz P? ID:
NAME:0
F
PageWriter Trim Cardiograph Instructions for Use 1-33
![Page 52: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/52.jpg)
Getting Started PageWriter Trim II and III Features
PageWriter Trim II and III Command ToolbarThe Command Toolbar includes all of the main functions of the cardiograph. Press the Tab key ( ) or turn the Trim Knob to highlight a button. Press the space bar ( ) or press the Trim Knob to select the button.
Figure 1-35 Command Toolbar
Table 1-8 Command Toolbar
Button Select this Button to...
Change Auto ECG settingsChange pacing detection settingsChange Rhythm report settingsChange the lead on a Disclose report
Turn on or turn off optional filters (Baseline Wander, Artifact)
Print a report of one minute of continuous waveform data for one selected lead
Load Orders on the cardiograph from a PC card or a USB memory stick
Enter an Order using the keyboard, or edit or delete Orders
Review, edit, or print saved 12-lead ECGs
Transfer 12-lead ECGs to a TraceMasterVue ECG Management System
Download ECGs from a TraceMasterVue Remote Site and view and print ECGs on the cardiograph
Configure the cardiograph or change configured settings Change the access passwords for features on the cardiographSave all cardiograph configured settings to a PC card or to a USB memory stick in case of system failure Save all cardiograph configured settings to a PC card or to a USB memory stick in order to upload the settings to multiple cardiographs
Get Help when using the cardiograph
REPORT FILTER DISCLOSE ORDER ARCHIVE HELPCONFIG
REPORT
FILTER
DISCLOSE
ORDERS
ARCHIVE
CONFIG
Help
1-34 PageWriter Trim Cardiograph Instructions for Use
![Page 53: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/53.jpg)
Getting Started Supplies and Ordering Information
Supplies and Ordering InformationThe part numbers for all supplies for the PageWriter Trim cardiograph are listed in this section.
Ordering Supplies
All supplies may be ordered on the web at:http://shop.medical.philips.com
Use the part numbers listed below for reference to ensure that the correct supplies are ordered.
PageWriter Trim Cardiograph Supply Part Numbers
Change the current date and time
Table 1-8 Command Toolbar (continued)
Button Select this Button to...
Patient Interface Module (PIM)
Part Number Description
989803130091 Patient Interface Module (AAMI)
989803130101 Patient Interface Module (IEC)
Replacement Fuse
Part Number Description
453564000371 1.5 amp (250 V) Time-Delay Fuse
Complete Lead Sets
Part Number Description
989803129161 Complete Lead Set (AAMI)
989803129191 Complete Lead Set (IEC)
Replacement Lead Sets and Accessories
Part Number Description
989803129141 Limb Lead Set, 99 cm/39 in (AAMI)
PageWriter Trim Cardiograph Instructions for Use 1-35
![Page 54: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/54.jpg)
Getting Started Supplies and Ordering Information
989803129151 Chest Lead Set, 61 cm/24 in (AAMI)
989803129171 Limb Lead Set, 99 cm/39 in (IEC)
989803129181 Chest Lead Set, 61 cm/24 in (IEC)
989803129201 Long Limb Lead Set, 137 cm/54 in (IEC)
989803129211 Long Chest Lead Set, 99 cm/39 in (IEC)
989803129221 Long Complete Lead Set (IEC)
Electrodes
Part Number Description
13943B Disposable cardiography electrode, resting diagnostic ECG
M2253A Disposable electrode, adult, resting ECG(not available in Japan)
40420A Disposable electrode, diagnostic, pre-gelled
13944B Wet Gel Foam Electrode, resting ECG
989803129231 Alligator Clips for Disposable Tab Electrodes (AAMI)
989803129241 Alligator Clips for Disposable Tab Electrodes (IEC)
M2254A Tab electrode adapter
40431B Alligator Clip Adapter for 1/8 post
40498E Snap Lead Electrode (IEC)
40475A Snap Lead Electrode Adapter
40490E 15mm Suction Electrode
40421A Push-in Connect Welsh Electrode
40494E Limb Clamp Electrode C400 (4 per box)
40491E Limb Plate Electrode C400 (4 per bag)
40424A Limb Plate Electrode (4 pack)
14030A Strap Electrode, 14 inch limb (4 per pack)
Replacement Lead Sets and Accessories (continued)
Part Number Description
1-36 PageWriter Trim Cardiograph Instructions for Use
![Page 55: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/55.jpg)
Getting Started Supplies and Ordering Information
Cardiograph AccessoriesFor more information on optional cardiograph accessories or to place an order, contact your Philips Sales Representative the Philips Response Center nearest you, see page 1-38.
Printer Paper
Part Number Description
M3707A Thermal Paper (100 sheets), A size (8.5 x 11 in/21.6 x 28 cm)
M3708A Thermal Paper (100 sheets) A4 size (8.27 x 11.69 in/21 x 29.69 cm)
Battery
Part Number Description
989803130151 PageWriter Trim Replacement Battery
Optional Cardiograph Accessories
Part Number Description
989803129931 Barcode Reader
989803129941 Magnetic Card Reader
989803127331 PC card (128 MB storage)
989803129961 SmartCard Reader
989803130131 Patient Cable Arm
989803142041 Wireless LAN Card
989803129951 LAN PCMCIA Network Card
989803145331 USB Memory Stick
989803144601 PageWriter Trim Cardiograph User Documentation CD (additional copies)
989803130111 PageWriter Trim Cardiograph Cart
989803130121 PageWriter Trim Cardiograph Cart Additional Shelf
989803127441 Optional Locking Drawer for Cardiograph Cart
989803127461 Modem Card (USA and Canada only)
989803138021 LAN Cable
PageWriter Trim Cardiograph Instructions for Use 1-37
![Page 56: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/56.jpg)
Getting Started Contacting a Philips Response Center
Contacting a Philips Response Center The Philips Response Center can assist with product troubleshooting and provide technical expertise to help with any issue with the PageWriter Trim cardiograph or any of its accessories.
For more information on the Philips Response Center go to:
www.medical.philips.com/main/services/response_center
North America Response Centers
Country Telephone Number
Canada (800) 323 2280
Mexico 01 800 710 8128
Puerto Rico 1 787 754 6811
United States (800) 722 9377
South America Response Centers
Country Telephone Number
Argentina 54 11 4546 7698
Brazil 0800 701 7789
Chile 0800 22 3003
Columbia 01 8000 11 10 10
Peru 51 1 620 6440
Europe Response Centers
Country Telephone Number
United Kingdom 44 0870 532 9741Fax: 44 01737 23 0550
Austria 43 1 60101 820
Belgium 32 2 525 7102 (French)32 2 525 7103 (Flemish)
Czech RepublicMCR Response Center(located in The Netherlands)
31 40 2781619
Denmark 45 80 30 30 35
Finland 358 615 80 400
1-38 PageWriter Trim Cardiograph Instructions for Use
![Page 57: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/57.jpg)
Getting Started Contacting a Philips Response Center
France 0 810 835 624
Germany 0180 5 47 5000
GreeceMCR Response Center(located in The Netherlands)
31 40 2781619
HungaryMCR Response Center(located in The Netherlands)
31 40 2781619
Italy 0800 232100
Netherlands 31 40 27 211 27
Norway 47 800 84 080
PolandMCR Response Center(located in The Netherlands)
31 40 2781619
RumaniaMCR Response Center(located in The Netherlands)
31 40 2781619
RussiaMCR Response Center(located in The Netherlands)
31 40 2781619
Slovak RepublicMCR Response Center(located in The Netherlands)
31 40 2781619
Spain 34 90 230 4050
Sweden 46 200 81 00 10
Switzerland 0800 80 3000 (German)0800 80 3001 (French)
Asia Response Centers
Country Telephone Number
Australia 1800 251 400
China 800 810 0038
Europe Response Centers (continued)
Country Telephone Number
PageWriter Trim Cardiograph Instructions for Use 1-39
![Page 58: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/58.jpg)
Getting Started Contacting a Philips Response Center
Hong Kong 852 2876 7578
India 1600 112 444
Indonesia 62 21 7910040, ext 8610
Japan 81 (0)120 095 205
Korea 82 (0)2 3445 9010
Malaysia 1800 886 188
New Zealand 0800 251 400
Philippines 63 2 8162617 ext. 875
Singapore 1800 Philips
Taiwan 0800 005 616
Thailand 66 (0)2 614 3569
Africa and Middle East
Country Telephone Number
All countries MCR Response Center(located in The Netherlands)
31 40 2781619
Asia Response Centers (continued)
Country Telephone Number
1-40 PageWriter Trim Cardiograph Instructions for Use
![Page 59: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/59.jpg)
2
1PageWriter Trim II and IIIConfiguration
IntroductionSettings on the PageWriter Trim II and III cardiographs are configurable to meet the needs of any clinical environment. The cardiograph is shipped with factory default settings, and any of these settings may be changed.
There are no configurable features on the PageWriter Trim I cardiograph. Please see "The Patient Session" on page 3-1, and complete the Interactive Training Program on CD to learn how to use the features of the cardiograph. These files may also be downloaded from the Philips InCenter web site (incenter.medical.philips.com). For information on using the Philips InCenter web site, see page 1-4.
Configuring Multiple CardiographsWhen configuring multiple cardiographs with the same settings, configure one cardiograph with all custom settings and then save the configured settings as a configuration settings file to a PC card or to a USB memory stick. The configuration settings file may then be uploaded to additional cardiographs. see "Saving Configured Settings" on page 2-46 for more information.
Password AccessAccess to all configuration options on the cardiograph may be set to be password access controlled. It is recommended that the Password screen be configured first, see page 2-40.
Configuring the Wireless LAN CardFor information on configuring the wireless LAN option for the PageWriter Trim cardiograph, please see the PageWriter Trim Cardiograph Wireless LAN Installation Instructions included on the User Documentation CD, or download the file from the Philips InCenter web site (incenter.medical.philips.com). For information on using the Philips InCenter web site, see page 1-4.
2-1
![Page 60: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/60.jpg)
PageWriter Trim II and III Configuration Opening the Configuration Screen
Configuration with a Philips TraceMasterVue ECG Management SystemIf a Philips TraceMasterVue ECG Management System is used with the PageWriter Trim cardiograph, please note that certain types of ECG information will not be transferred from the cardiograph to TraceMasterVue.
For detailed information on configuring the PageWriter Trim cardiograph with a TraceMasterVue ECG Management System, see the Configuring Cardiograph and TraceMasterVue Communication Guide available for download from the Philips InCenter web site (incenter.medical.philips.com). For information on using the Philips InCenter web site, see page 1-4.
Restoring Custom SettingsAfter configuring the cardiograph, save the settings to a PC card or to a USB memory stick in case of system failure. If the cardiograph loses configured settings, the settings may be quickly and easily restored by loading them onto the cardiograph with a PC card or a USB memory stick. see "Loading the Configuration Settings File" on page 2-47 for more information.
Opening the Configuration ScreenAll custom settings for the cardiograph are specified on the Configuration screens.
To open the configuration screen:
1 Press the Tab key ( ) or turn the Trim Knob to highlight the Config button on the Command Toolbar.
2 Press the space bar ( ) or the Trim Knob to select the button. The Configuration screen appears. A series of tabs appear at the top of the screen. Under each tab are a set of configurable features.
Figure 2-1 The Configuration Screen
CONFIG
Analysis (A) Patient ID (I) Profiles (P) System (S) Orders (Q) Rhythm (V)
(page 2-3) (page 2-8) (page 2-17) (page 2-23) (page 2-28) (page 2-29)
Filter (F) Remote Sites(R)
Network (N) Passwords (W)
Locale (L) Cardiograph (C)
(page 2-30) (page 2-33) (page 2-38) (page 2-40) (page 2-41) (page 2-42)
2-2 PageWriter Trim Cardiograph Instructions for Use
![Page 61: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/61.jpg)
PageWriter Trim II and III Configuration Analysis Settings
To select a tab:
1 Press and hold down the Alt key ( ) on the keyboard.
2 Press the letter shown in parenthesis on the tab. For example, to select the Analysis tab, press and hold down the Alt key, and then press the A key on the keyboard.
To save settings on any configuration screen:
After making all changes to the cardiograph configuration screens, press the Enter key ( ) on the keyboard to save the settings and to exit the screen.
To exit the configuration screens without saving changes:
Press the Esc key ( ) on keyboard to exit any configuration screen without saving the information.
Analysis SettingsThis section is used to configure the settings used with the Philips 12-Lead Algorithm, including selecting the algorithm version, setting the default pacing detection setting, the adult bradycardia limit, and configuring the statement that appears on the printed 12-lead ECG indicating that the ECG has not been overread by a qualified physician.
About Algorithm VersionsThe PageWriter Trim cardiograph supports two versions of the Philips 12-Lead Algorithm. Both versions of the algorithm may be configured to provide interpretive, reason, and severity statements that appear on the ECG report.
The algorithm version PH080A is the factory default algorithm, and is compatible with all versions of the TraceMaster and TraceMasterVue ECG Management System, and with the PageWriterTouch cardiograph.
The algorithm version PH090A is only compatible with the TraceMasterVue ECG Management System version A.02.01 and higher. This version provides all of the same features as version PH080A, with the following enhancements:
heightened detection of atrial arrhythmias including: atrial fibrillation, atrial flutter, and second and third degree AV blocks
ability to suppress interpretive statements that indicate a borderline condition
optional automatic lead reversal detection feature for both limb leads (RA and LA), and the precordial leads
calculation of Fridericia rate corrected QT interval
PageWriter Trim Cardiograph Instructions for Use 2-3
![Page 62: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/62.jpg)
PageWriter Trim II and III Configuration Analysis Settings
Setting the Default Pacing Detection SettingThe default pacing detection setting appears on the Status Bar at the beginning of each patient session.
NOTE The default Pacing Detection Setting may be changed at any time during a patient session by selecting the Report button on the Command Toolbar (see page 1-34).
Figure 2-2 Pacing Detection Setting on the Status Bar
Factory Default Settings
Philips 12-Lead Algorithm Version: PH080A
Pacing Detection Setting: Not Known if Paced (P?)(recommended for most ECGs)
Report Confirmation Label: Unconfirmed Diagnosis
Adult Bradycardia Limit: 50 (bpm)
A Pacing Detection Setting
A
RL 60~0.15 - 150 Hz P? ID:
NAME:0
2-4 PageWriter Trim Cardiograph Instructions for Use
![Page 63: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/63.jpg)
PageWriter Trim II and III Configuration Analysis Settings
There are four pacing detection settings that are available as the default setting on the cardiograph. These settings are described in Table 2-1. The pacing detection setting may be changed for an individual patient session when necessary.
Table 2-1 Pacing Detection Setting Description
Setting Description Symbol on Status Bar and printed ECG
Not known if paced
This is the default setting and normally is used for both paced and non-paced patients
Pacemaker pulse detection is on and is at normal sensitivity
Occasional false pacemaker pulse detections may occur in ECGs with excessive noise
False detections may result in an incorrect interpretive statement appearing on the report
Small amplitude pacemaker pulses may not be detected using this setting
P?
Non-paced Pacemaker pulse detection is offUse this setting if there are false pacemaker pulse detections from noise, or if incorrect interpretive statements or inappropriate paced ECG complexes appear on the report
No code appears on the Status Bar if the Non-paced setting is selected
Paced Pacemaker pulse detection is on and is set at a higher sensitivityUse this setting if small amplitude pacemaker pulses are not being detected at the default (Not Known if Paced) settingFalse pacemaker pulse detections may occur if the ECG is noisy
P
PageWriter Trim Cardiograph Instructions for Use 2-5
![Page 64: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/64.jpg)
PageWriter Trim II and III Configuration Analysis Settings
To set the default pacing detection setting:
1 Press and hold down the Alt key ( ) on the keyboard.
2 Press the A key on the keyboard.
3 The Analysis screen appears. Under Pacer Detect, Not Known if Paced (recommended setting) is selected.
4 To select another setting, turn the Trim Knob or press the Tab key ( ) to highlight the setting.
5 Press the space bar (on keyboard) or the Trim Knob to select the setting.
Setting the Report Status Statement The statement Unconfirmed Diagnosis or any other customized text can be configured to appear on the ECG report to designate that the report has not been overread by a qualified physician. To have the default statement Unconfirmed Diagnosis appear on the printed ECG report, do not change this setting. To customize a statement or to have no statement appear on the report, follow the procedure below.
To configure the report status statement:
1 Turn the Trim Knob or press the Tab key ( ) to select the field under Report Confirmation Label.
2 Press the space bar (on keyboard) to delete the statement. No statement will appear on the printed ECG report. Or, type in a customized statement to appear on the ECG report.
Paced (magnet)
Use this setting if the ECG is acquired with an active pacemaker magnet or programmer in placePacemaker pulse detection is on and is at a higher sensitivityMagnets or programmers often put the pacemaker into a fixed-rate, non-sensing modeThe statement ECG ACQUIRED WITH MAGNET IN PLACE is printed on the 12-lead ECG notifying the overreader that a magnet or programmer was used and would explain the fixed rate behavior of the pacer
PM
Table 2-1 Pacing Detection Setting Description (continued)
Setting Description Symbol on Status Bar and printed ECG
2-6 PageWriter Trim Cardiograph Instructions for Use
![Page 65: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/65.jpg)
PageWriter Trim II and III Configuration Analysis Settings
Setting the Default Adult Bradycardia LimitThe default adult bradycardia limit that is used when interpreting waveform data with the Philips 12-lead Algorithm is configurable. For more information on adult bradycardia limits and the Philips 12-Lead Algorithm, see the Philips 12-Lead Algorithm Physician’s Guide on the PageWriter Trim User Documentation CD, or download the file from the Philips InCenter web site (incenter.medical.philips.com).
To set the adult bradycardia limit setting:
1 Press the Tab key ( ) or turn the Trim Knob to select the setting under Adult Bradycardia Limit.
2 Press the space bar (on keyboard) or the Trim Knob. The drop-down list of available settings appears.
3 Press the up or down arrow keys ( ) or turn the Trim Knob to highlight a setting.
4 Press the space bar (on keyboard) or the Trim Knob to select the setting.
Setting the Philips 12-Lead Algorithm VersionThe default algorithm version PH080A may be changed to algorithm version PH090A. For information on algorithm version PH090A, see “About Algorithm Versions” on page 2-3.
To select the algorithm version:
1 Press the Tab key ( ) or turn the Trim Knob until the algorithm version (PH080A or PH090A) is highlighted.
2 Press the space bar or the Trim Knob to select the algorithm version.
3 If version PH090A is selected, a group of configurable options appear on the screen.
NOTE Algorithm version PH090A is only compatible with TraceMasterVue ECG Management System version A.02.01 and higher, and is not compatible with the PageWriterTouch cardiograph.
4 Press the Tab key or turn the Trim Knob to highlight the Check Lead Placement setting. Press the space bar to select the check box. This option enables the automatic lead reversal detection feature for limb leads RA and LA, and the precordial leads. When the algorithm detects that leads have been reversed, a statement will appear on the ECG report.
About the Borderline Statement Suppression SettingThis feature may be configured to suppress interpretive statements that indicate a borderline or otherwise normal condition. These borderline interpretive statements are generated by measurements that are above an abnormal threshold, but may in fact indicate a non-pathological condition. These statements indicate to the clinician that a condition may be present, but there is no decisive indicator. Borderline interpretive statements include the terms minimal, consider, borderline, or probable.
The borderline statement suppression setting is configurable to three levels of sensitivity as described in Table 2-2.
PageWriter Trim Cardiograph Instructions for Use 2-7
![Page 66: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/66.jpg)
PageWriter Trim II and III Configuration Patient ID Settings
For a complete listing of all borderline interpretive statements that are suppressed using this feature, see Appendix A, “Suppressed Borderline Interpretive Statements.”
To select a borderline statement suppression setting:
1 Press the Tab key ( ) or turn the Trim Knob until the setting is highlighted.
2 Press the space bar to select the radio button.Select another tab (top of screen) to continue making changes. If done making changes, press the Enter key ( ) to save the changes and to exit the Configuration screen. The new changes are applied.
Patient ID SettingsThe Patient ID settings are used to configure the amount and type of information that appears on the Patient ID screen when the Patient ID button (right side of the cardiograph) is pressed. The Patient ID screen is used during a patient session to enter patient information.
CAUTION Age and Gender Patient ID information are required if using the Philips 12-Lead Algorithm for ECG interpretation. For more information, see the Philips 12-Lead Algorithm Physician’s Guide on the PageWriter Trim User Documentation CD, or download the file from the Philips InCenter web site (incenter.medical.philips.com).
To open the Patient ID configuration screen:
1 Push and hold down the Alt key ( ) on the keyboard.
2 Press the I key on the keyboard to open the Patient ID configuration screen.
Table 2-2 Borderline Statement Suppression Settings Description
Borderline Suppression Setting
Description
Level 0 - none This setting turns off all borderline statement suppression; no statements are suppressed.
All borderline or otherwise normal interpretive statements will appear on the printed ECG report.
Level 1 - few This setting will suppress certain borderline interpretive statements.See Appendix A, “Suppressed Borderline Interpretive Statements” for a complete listing of the interpretive statements that are suppressed using this setting.
Level 2 - many This setting will suppress the maximum number of borderline or otherwise normal interpretive statements. See Appendix A, “Suppressed Borderline Interpretive Statements” for a complete listing of the interpretive statements that are suppressed using this setting.
2-8 PageWriter Trim Cardiograph Instructions for Use
![Page 67: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/67.jpg)
PageWriter Trim II and III Configuration Patient ID Settings
3 Three tabs appear at the top of the screen. These tabs contain the three types of configurable Patient ID information available on the cardiograph. The Patient Info. tab is selected.
Figure 2-3 Patient ID Configurable Settings
Patient ID Configuration OptionsEach type of Patient ID information may be configured with up to four options as described in Table 2-3. These options appear as columns of check boxes on the left side of the screen. Select the check box underneath the option to enable it.
To select a check box:
1 Turn the Trim Knob or press the Tab key ( ) to highlight the ON text next to the check box.
2 Press the space bar (on keyboard) or the Trim Knob to select the check box. A check mark appears and the feature is enabled.
Configuring Patient InformationThese selections include demographic information about the patient including: name, ethnicity, age, gender, and other configurable information fields. This information appears under the Patient Info. tab when the Patient ID button (right side of cardiograph) is pressed.
Table 2-3 Patient ID configuration options
Setting Description
Enabled Select this check box to make this type of Patient ID information appear on the Patient ID screen.
This information is transferred with the ECG to a TraceMasterVue ECG Management System.
Required Select this check box to require that this type of Patient ID information be complete before the ECG is transferred to a Philips TraceMasterVue ECG Management System.
Indexed Select this check box to make this type of Patient ID information appear as a column on the Archive or Orders screen.
Printed Select this check box to include this type of Patient ID information on the printed ECG report.
Patient Info. (T) Clinical Info. (X) Order Info. (O)
(page 2-12)(page 2-9) (page 2-17)
PageWriter Trim Cardiograph Instructions for Use 2-9
![Page 68: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/68.jpg)
PageWriter Trim II and III Configuration Patient ID Settings
There are two optional and configurable text entry fields available labeled <User Field 1> and <User Field 2>. These optional text entry fields may be configured to appear on the Patient ID screen during a patient session.
Each type of Patient Information can be configured using four different settings: Enabled, Required, Indexed, and Printed (see Table 2-3 on page 2-9).
To configure Patient Information:
1 Press and hold down the Alt key ( ) on the keyboard.
2 Press the I key. The Patient ID screen appears.
Table 2-4 Patient Information Description
Patient Information Description
Patient First Name Up to 40 characters in length
Patient Last Name Up to 40 characters in length
Patient Additional Name Up to 40 characters in length
Race (Ethnicity) Drop-down list selection
Pre-defined drop-down list
Patient Age Patient age is configurable and can be entered by:– Configurable units (years, hours, days, weeks,
months)– Date of birth (month, day, year)
A default age is specified for ECG interpretation when no patient age is entered
Patient Gender Radio button selection (male, female, unknown)
User Defined text entry field
Text entry field label up to sixteen characters in length
Text entry field is free text entry up to thirty-two characters in length
Factory Default Settings
Patient ID fields selected:
Patient last name (Enabled, Printed)
Age and date of birth (Enabled, Printed)
50 (default patient age used when no age is entered)
Gender (Enabled, Printed)
2-10 PageWriter Trim Cardiograph Instructions for Use
![Page 69: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/69.jpg)
PageWriter Trim II and III Configuration Patient ID Settings
3 Press and hold down the Alt key on the keyboard.
4 Press the T key to select the Patient Info. tab (if not selected).
5 Press the Tab key ( ) or turn the Trim Knob to highlight the ON text next to a check box of a feature to be enabled.
6 Press the space bar (on keyboard) or the Trim Knob to select a check box. A check mark appears in the selected check box and enables the patient information field.
7 Press the Tab key or turn the Trim Knob to select the drop-down list next to Age/DOB.
8 Press the space bar (on keyboard) or the Trim Knob to display the drop-down list.
9 Press the up or down arrow keys to scroll through the list and to highlight a default age unit (DOB-date of birth, Years, Days, Weeks, Hours).
10 Press the space bar or the Trim Knob to select the age unit.
11 Press the Tab key or turn the Trim Knob to highlight the age displayed under Default Age (Years). The Default Age (Years) selection sets the default age that is used for ECG interpretation when no patient age is entered. The factory default age setting is 50 years.
12 Type in the default age (using keyboard).
13 Press the Tab key or turn the Trim Knob to highlight the drop-down list next to Weight or Height.
14 Press the space bar or the Trim Knob to display the drop-down list.
15 Press the up or down arrow key ( ) to highlight a weight or height unit.
16 Press the space bar or the Trim Knob to select the weight or height unit.
User Defined Patient Information
There are two optional Patient Information text entry fields labeled <User Field 1> and <User Field 2>. When the Patient ID button is pressed during a patient session, these configurable text entry fields appear under the Patient Info. tab, and are located at the bottom of the screen.
A text label is created in Configuration to describe the text entry field. The text entry field is completed on the Patient ID screen during a patient session by typing information in the field.
To configure the text field label:
1 Ensure that <User Field 1> and <User Field 2> check boxes for Enabled, Required, Indexed, or Printed are selected. If these check boxes are not selected, the user defined fields will not appear on the Patient ID screen.
2 Turn the Trim Knob or press the Tab key ( ) to select the field next to <User Field 1> or <User Field 2>. The cursor appears in the field.
3 Type in any sixteen letters or numbers with the keyboard to create the text field label. This label appears on the Patient ID screen.Select another tab (top of screen) to continue making changes. If done making changes, press the Enter key ( ) to save the changes and to exit the Configuration screen. The new changes are applied.
PageWriter Trim Cardiograph Instructions for Use 2-11
![Page 70: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/70.jpg)
PageWriter Trim II and III Configuration Patient ID Settings
Configuring Clinical InformationThe following Clinical Information fields may be configured to appear on the Patient ID screen:
Symptoms (Sx)
History (Hx)
Prescriptions (Rx)
Diagnoses (Dx)
Diagnostic Related Group (DRG)
Blood Pressure
On the Patient ID screen, the user selects Clinical Information from a pre-defined list of entries, or can manually enter information in the clinical fields.
There are two optional and configurable text entry fields available labeled <User Field 3> and <User Field 4>.
Each type of Clinical Information can be configured using four different settings: Enabled, Required, Indexed, and Printed (see Table 2-3 on page 2-9).
Table 2-5 Clinical Information Description
Clinical Information Description
Sx (Symptoms) Configurable drop-down list
Selections from drop-down list can be up to thirty-two characters in length
Hx (History) Configurable drop-down list
Selections from drop-down list can be up to thirty-two characters in length
Rx (Prescriptions) Configurable drop-down list
Selections from drop-down list can be up to thirty-two characters in length
Factory Default Settings
No Clinical Information fields are selected
2-12 PageWriter Trim Cardiograph Instructions for Use
![Page 71: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/71.jpg)
PageWriter Trim II and III Configuration Patient ID Settings
To configure Clinical Information:
1 Press and hold down the Alt key ( ) on the keyboard.
2 Press the I key. The Patient ID screens appear.
3 Press and hold down the Alt key on the keyboard.
4 Press the X key to select the Clinical Info. tab.
5 Press the Tab key ( ) or turn the Trim Knob to highlight the ON text next to a check box of a feature to be enabled.
6 Press the space bar (on keyboard) or the Trim Knob to select a check box. A check mark ( ) appears in the selected check box and enables the clinical information field.
7 Press the Tab key or turn the Trim Knob to highlight the drop-down list next to Sx (Symptoms).
8 Press the space bar or the Trim Knob to review the available selections in the drop-down list.
9 To add a new entry, press the Tab key or turn the Trim Knob to highlight the + button.
10 Press the space bar or the Trim Knob. The Please input data window appears.
11 Type in the new symptom (up to thirty-two characters in length).
12 Press the Tab key or turn the Trim Knob to highlight the OK button.
13 Press the space bar or Trim Knob to add the symptom. The new symptom appears in the drop-down list. Follow the same procedure to add drop-down list entries for Hx (History), Rx (Prescriptions), Dx (Diagnosis), and DRG (Diagnostic Related Group)
Dx (Diagnoses) Configurable drop-down list
Selections from drop-down list can be up to thirty-two characters in length
DRG (Diagnostic Related Group)
Configurable drop-down list
Selections from drop-down list can be up to thirty-two characters in length
Blood Pressure Numeric entry
Systolic, diastolic
User Defined text entry field
Drop-down list label up to sixteen characters in length
Text field is free text entry up to thirty-two characters in length
Table 2-5 Clinical Information Description (continued)
Clinical Information Description
PageWriter Trim Cardiograph Instructions for Use 2-13
![Page 72: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/72.jpg)
PageWriter Trim II and III Configuration Patient ID Settings
To delete a user-defined symptom:
1 Select the symptom to be deleted from the drop-down list.
NOTE Factory default symptoms cannot be deleted from the drop-down list.
2 Press the Tab key or turn the Trim Knob to highlight the - button.
3 Press the space bar or the Trim Knob. The Delete Sx Label window appears.
4 Press the space bar or the Trim Knob to select the OK button. The user- defined symptom is deleted from the drop-down list. Follow the same procedure to delete drop-down list entries for Hx (History), Rx (Prescriptions), Dx (Diagnosis), and DRG (Diagnostic Related Group).
User Defined Clinical Information
There are two optional Clinical Information text entry fields that can be configured labeled <User Field 3> and <User Field 4>. When the Patient ID button is pressed during a patient session, these configurable text entry fields appear under the Clinical Info. tab, and are located at the bottom of the screen.
A text label is created in Configuration to describe the text entry field. The text entry field is completed on the Patient ID screen during a patient session by typing information in the field.
To configure the text label:
1 Ensure that the <User Field 3> and <User Field 4> check boxes for Enabled, Required, Indexed, or Printed are selected. If these check boxes are not selected, the user defined fields will not appear on the Patient ID screen or on the printed ECG.
2 Turn the Trim Knob to select the field next to <User Field 3> or <User Field 4>. The cursor appears in the field.
3 Type in any sixteen letters or numbers with the keyboard to specify a text label for the field. Select another tab (top of screen) to continue making changes. If done making changes, press the Enter key ( ) to save the changes and to exit the Configuration screen. The new changes are applied.
Configuring Order InformationThe following Order information may be configured to appear on the Patient ID screen:
Reason for Order
Physician Name
UPIN (Universal Physician Identification Number)
Department
Operator ID
Room number
Order Number
2-14 PageWriter Trim Cardiograph Instructions for Use
![Page 73: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/73.jpg)
PageWriter Trim II and III Configuration Patient ID Settings
Encounter ID
STAT ECG
There are two optional and configurable text entry fields available labeled <User Field 5> and <User Field 6>. These optional text entry fields appear on the Patient ID screen during a patient session.
Each type of Order Information can be configured using four different settings: Enabled, Required, Indexed, and Printed (see Table 2-3 on page 2-9).
Table 2-6 Order Information Description
Order Information Description
Reason for Order Configurable drop-down list
Drop-down list selections up to thirty-two characters in length
Physician Name and UPIN (Universal Physician Identification Number)
Configurable drop-down list
Drop-down list selections up to thirty-two characters in length
Department Number Configurable drop-down list
Drop-down list selections up to thirty-two characters in length
Operator ID Configurable drop-down list
Drop-down list selections up to thirty-two characters in length
Room Number Free text entry
Up to thirty-two characters in length
Order Number Free text entry
Up to thirty-two characters in length
Encounter ID Free text entry
Up to thirty-two characters in length
Factory Default Settings
No Order Information fields are selected
PageWriter Trim Cardiograph Instructions for Use 2-15
![Page 74: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/74.jpg)
PageWriter Trim II and III Configuration Patient ID Settings
To configure Order Information:
1 Press and hold down the Alt key ( ) on the keyboard.
2 Press the I key. The Patient ID screens appear.
3 Press and hold down the Alt key on the keyboard.
4 Press the O key to select the Order Info. tab.
5 Press the Tab key ( ) or turn the Trim Knob to highlight the ON text next to a check box of a feature to be enabled.
6 Press the space bar or the Trim Knob to select a check box. A check mark ( ) appears in the selected check box and enables the Order information field.
7 Press the Tab key or turn the Trim Knob to highlight the + button next to Reason for Order.
8 Press the space bar (on keyboard) or the Trim Knob. The Please input data window appears.
9 Type in a reason for order (up to thirty-two characters in length).
10 Press the Tab key or turn the Trim Knob to highlight the OK button.
11 Press the space bar or the Trim Knob to add the reason for order. The new reason for order appears in the drop-down list.
To delete a reason for order from the drop down list:
1 Select the reason for order to be deleted from the drop-down list.
2 Press the Tab key ( ) or turn the Trim Knob to highlight the - button.
3 Press the space bar (on keyboard) or the Trim Knob. The Delete Reasons window appears.
4 Press the space bar or the Trim Knob to select the OK button. The reason for order is deleted from the drop-down list. Follow the same procedure to add or to delete drop-down list entries for Physician Name and UPIN, Department, and Operator ID.
STAT ECG Selectable drop-down list on Patient ID screen
STAT label printed on Auto ECG
User Defined text entry fields Text entry field label up to sixteen characters in length
Free text entry up to thirty-two characters in length
Table 2-6 Order Information Description (continued)
Order Information Description
2-16 PageWriter Trim Cardiograph Instructions for Use
![Page 75: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/75.jpg)
PageWriter Trim II and III Configuration Configuring Auto ECG Report Profiles
User Defined Order Information
There are two optional Order Information text entry fields that can be configured labeled <User Field 5> and <User Field 6>. When the Patient ID button is pressed during a patient session, these configurable text entry fields appear under the Order Info. tab on the Patient ID screen.
A text label is created in Configuration to describe the text entry field. The text entry field is completed on the Patient ID screen during a patient session.
To configure the text label:
1 Ensure that the <User Field 5> and <User Field 6> check boxes for Enabled, Required, Indexed, or Printed are selected. If these check boxes are not selected, the user defined fields will not appear on the Patient ID screen or on the printed ECG.
2 Turn the Trim Knob or press the Tab key ( ) to select the field next to <User Field 5> or <User Field 6>. The cursor appears in the field.
3 Type in any sixteen letters or numbers with the keyboard. The text field label is entered and will appear on the Patient ID screen.Select another tab (top of screen) to continue making changes. If done making changes, press the Enter key ( ) to save the changes and to exit the Configuration screen. The new changes are applied.
Configuring Auto ECG Report ProfilesTIP Review “Reading the Printed ECG Report” on page 5-1 before configuring Auto ECG report profiles.
This file is available on the User Documentation CD, or may be downloaded from the Philips InCenter web site (incenter.medical.philips.com).
A profile is a group of settings applied to Auto ECGs and to copies of Auto ECGs. A profile defines how the Auto ECG or ECG copy appears when printed. The Auto ECG or ECG copy is generated when the Auto or Copy buttons (right side of cardiograph) are pressed during a patient session.
PageWriter Trim Cardiograph Instructions for Use 2-17
![Page 76: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/76.jpg)
PageWriter Trim II and III Configuration Configuring Auto ECG Report Profiles
Figure 2-4 The Report and Copy Profile
There is one factory default report profile (Default Main) and one factory default copy report profile (Default Copy).
The factory default report and copy profile may be edited, or new, customized profiles may be created.
NOTE The factory default report profile (Default Main) and copy profile (Default Copy) may not be deleted.
Figure 2-5 The Factory Default Report Profile (Default Main)
The Profile
Speed (mm/sec) and Size (mm/mV) of waveforms
Lead Sequence: Standard or Cabrera
ECG Signal Acquisition: Time-Sequential or Simultaneous
Lead Configuration on printed report (3x4, 3x4 1R, 3x4 3R, 6x2, 12x1, Pan-12)
Extended Measurements Report: enabled or not enabled
Level of ECG interpretation using the Philips 12-Lead Algorithm (Measurements, Interpretive and Reason Statements, Severity Codes)
Default Main
Speed: 25 mm/sec
Size: 10 mm/mV
Chest Leads: Full Scale
Lead Configuration: 3x4, 1R
Lead Sequence: Standard
Acquisition: Time-Sequential
Interpretation Level: None
2-18 PageWriter Trim Cardiograph Instructions for Use
![Page 77: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/77.jpg)
PageWriter Trim II and III Configuration Configuring Auto ECG Report Profiles
Figure 2-6 The Factory Default Copy Profile (Default Copy)
To open the profile screens:
1 Press and hold down the Alt key ( ) on the keyboard.
2 Press the P Key on the keyboard. The Profile screen appears. Under Profiles List (left side of screen) Default Main is highlighted. Default Main is the factory default Auto 12-lead ECG report profile. This profile may be edited or new profiles may be created.Four tabs appear on the left side of the Profiles screen. Under each tab are ECG report settings that may be edited.
Figure 2-7 The Profile tabs
NOTE The Interps (G) and Type (K) tabs only appear if the Philips 12-Lead Algorithm is enabled on the cardiograph.
To edit a factory default or existing profile:
1 Under Profiles List (left side of screen) an Auto ECG report profile is highlighted. This is the profile selected to be edited. The settings for this profile are displayed on the screen. To select a different profile for editing, press the space bar or the Trim Knob to display the drop-down list.
2 Press the up or down arrow key ( ) to scroll through the list and to highlight a profile to be edited.
3 Press the space bar (on keyboard) or the Trim Knob to select a the report profile for editing. The drop-down list closes and the selected report profile appears highlighted under Profiles List.
Default Copy
Speed: 25 mm/sec
Size: 10 mm/mV
Chest Leads: Full Scale
Lead Configuration: 3x4, 1R (Rhythm Lead: II)
Lead Sequence: Standard
Acquisition: Time-Sequential
Interpretation Level: None
Number of report copies printed: 1
Format (M) Scale (J)
(page 2-20) (page 2-20) (page 2-21)
Interps (G) Type (K)
(page 2-21)
PageWriter Trim Cardiograph Instructions for Use 2-19
![Page 78: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/78.jpg)
PageWriter Trim II and III Configuration Configuring Auto ECG Report Profiles
Editing the Profile Report FormatThe profile report format settings define the lead sequence and acquisition type that appear on the Auto ECG.To edit the report format:
1 If the Format (M) tab is not selected, press and hold down the Alt key ( ) on keyboard. Press the M key. The Format screen appears.
2 Press the Tab key ( ) or turn the Trim Knob until the drop-down list under Lead Configuration is highlighted.
3 Press the space bar (on keyboard) or the Trim Knob to display the list of available report formats. Press the up or down arrow keys ( ) to scroll through the list.
4 Press the space bar or the Trim Knob to select a report format. The selected report format appears highlighted under Lead Configuration.If the selected report format includes rhythm strips, the default rhythm leads are displayed under Rhythm.
5 Press the Tab key or turn the Trim Knob to highlight the Lead Groups>>> button (3x4, 3R only). Press the space bar or the Trim Knob to display pre-defined groups of three rhythm leads. Or, turn the Trim Knob or press the Tab key to highlight the drop-down list next to R1 (R2, R3) and select the rhythm leads individually.
6 Under Lead Sequence, the default settings for the selected report format are displayed. Press the Tab key or turn the Trim Knob to highlight the lead sequence drop-down list (Standard, Cabrera).
NOTE The Pan-12 report format is only available with Cabrera lead sequence and Time-Sequential acquisition.
NOTE The 12x1 report format is only available with Simultaneous acquisition.
7 Press the space bar or the Trim Knob to display the drop-down list.
8 Press the up or down arrow key to highlight a lead sequence.
9 Press the space bar to select a lead sequence.
10 Follow the same procedure to select an ECG acquisition type (Simultaneous, Time-Sequential) for the report profile.
Editing Profile InterpretationThe interpretation settings define how much interpretive information from the Philips 12-lead Algorithm appears on the Auto ECG.
To edit interpretation options:
1 Press and hold down the Alt key ( ).
2 Press the G key on the keyboard. The Interpretation screen appears.Under Interpretations, the different levels of interpretive information available with the Philips 12-lead Algorithm are displayed.
2-20 PageWriter Trim Cardiograph Instructions for Use
![Page 79: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/79.jpg)
PageWriter Trim II and III Configuration Configuring Auto ECG Report Profiles
3 Press the Tab key ( ) or turn the Trim Knob to highlight the desired setting.
NOTE Selecting None will have no interpretive information (including Basic Measurements) appear on the printed Auto ECG.
4 Press the space bar (on keyboard) or the Trim Knob to select the interpretive setting.
Editing Profile Scale InformationThe scale settings define the speed and the size of the waveforms appearing on the printed report. 1 Press and hold down the Alt key ( ) on the keyboard.
2 Press the J key. The Scale screen appears.
3 Press the Tab key ( ) or turn the Trim Knob to select settings under Speed, Size, and Chest Leads.
NOTE Chest Leads sets the precordial leads to full or half the scale of the limb and augmented leads.
4 Press the space bar (on keyboard) or the Trim Knob to select a setting.
Editing Report Type InformationThe Type setting enables the optional Extended Measurements Report. The Extended Measurements report summarizes the output of the Philips 12-Lead Algorithm and includes the morphology characteristics for the individual leads, along with the rhythm characteristics for the rhythm groups. The algorithm uses this measurement information to generate interpretive statements. The Extended Measurements report is especially useful if you want to examine the measurements used to generate an interpretation.
For more information on the Extended Measurements Report, see the Philips 12-Lead Algorithm Physician’s Guide on the User Documentation CD, or download the file from the Philips InCenter web site (incenter.medical.philips.com).1 Press and hold down the Alt key ( ) on the keyboard.
2 Press the K key. The Type screen appears.
3 Press the Tab key ( ) or turn the Trim Knob to highlight Extended Measurements.
4 Press the space bar (on keyboard) to select the check box. With the check box selected, the full Extended Measurements report is included with each Auto ECG.
Saving the Report Profile The selected settings may be saved to the current report profile, or a new report profile may be created using the selected settings.
PageWriter Trim Cardiograph Instructions for Use 2-21
![Page 80: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/80.jpg)
PageWriter Trim II and III Configuration Configuring Auto ECG Report Profiles
To save the settings to the selected report profile:
1 Press the Tab key ( ) or turn the Trim Knob until the Save button (top of screen) is highlighted. The new settings will be saved to the profile displayed under Profiles List.
NOTE To select a different profile, press the Tab key or turn the Trim Knob until the drop-down list under Profiles List is highlighted. Press the space bar or the Trim Knob to open the drop-down list. Press the up or down arrow key to highlight a profile. Press the space bar or the Trim Knob to select the profile.
2 Press the space bar or the Trim Knob to apply the new settings to the selected profile.The new settings are saved to the selected profile.
To create a new report profile:
1 Press the Tab key ( ) or turn the Trim Knob until the Add button (top of screen) is highlighted. Press the space bar or the Trim Knob.
2 The Please input data window appears. Type in the name of the new profile (up to thirty-two characters in length).
3 Press the Tab key to highlight the OK button.
NOTE Highlight the Cancel button and push the space bar or Trim Knob to exit without saving the profile name.
4 Press the space bar (on keyboard) or the Trim Knob to save the new profile.The new profile appears in the Profiles List drop-down list.
Setting the Default Auto Report and Copy ProfileThe default Auto report and copy profile are selected on the Profile configuration screen. Any Auto ECG or ECG copy printed on the cardiograph will apply the settings specified in the selected default profile.
During a patient session, the default profile may be changed and temporary settings applied by selecting the Report button on the Command Toolbar (see page 1-34).
To set the default report and copy profile:
1 Press the Tab key ( ) or turn the Trim Knob until the drop-down list under Select Defaults (Main) (right side of screen) is highlighted.
2 Press the space bar (on keyboard) or the Trim Knob to display the drop-down list of available Auto ECG report profiles.
3 Press the up or down arrow key ( ) to highlight a profile as the default Auto ECG report profile.
4 Press the space bar to select the profile.
5 Press the Tab key or turn the Trim Knob to highlight the drop-down list under Copy.
6 Press the space bar or the Trim Knob to display the drop-down list of available Copy profiles.
7 Press the up or down arrow key to highlight a profile.
REPORT
2-22 PageWriter Trim Cardiograph Instructions for Use
![Page 81: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/81.jpg)
PageWriter Trim II and III Configuration System Settings
8 Press the space bar or the Trim Knob to select the profile as the default Copy profile.
9 Press the Tab key or turn the Trim Knob to highlight the drop-down list next to Number of Copies.
10 Press the space bar or the Trim Knob to display the drop-down list.
11 Press the up or down arrow key to select the number of Auto ECG report copies (1-5) printed each time the Copy button (right side of cardiograph) is pressed.
Setting Other Print OptionsAdditional print options are available on the Profiles configuration screen. The Auto Save When Print option automatically saves all Auto ECGs to the Archive. The Archive serves as temporary storage for ECGs until they are saved to a PC card or to a USB memory stick, or are transferred by modem, fax, or a LAN connection to a TraceMasterVue ECG Management System. ECGs that are not saved to the Archive are deleted.
The Second ID Label option prints the patient name and ID at the top and the bottom of the ECG report.
The Print Immediately option automatically prints each ECG when the Auto button (right side of cardiograph) is pressed. If this option is not selected, the Auto ECG appears on the Preview screen. The user can assess the quality of the ECG directly on the Preview screen, and then print it by pressing the Enter key ( ) on the keyboard.
TIP Previewing the Auto ECG before printing it saves printer paper and helps to ensure a quality report.
To select other print options:
1 Press the Tab key ( ) or turn the Trim Knob until the option is highlighted (lower right of screen)
2 Press the space bar (on keyboard) to select the check box. A selected check box enables the feature. Select another tab (top of screen) to continue making changes. If done making changes, press the Enter key ( ) to save the changes and to exit the Configuration screen. The new changes are applied.
System SettingsThe configurable cardiograph settings in this section include:
paper size
keyboard caps lock feature
lead standard setting for printed ECGs (AAMI or IEC)
battery power saving modes
default display format
notification messages
ARCHIVE
PageWriter Trim Cardiograph Instructions for Use 2-23
![Page 82: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/82.jpg)
PageWriter Trim II and III Configuration System Settings
simulated waveform feature
This section also includes tools under Configuration Management (see page 2-46) and other maintenance and diagnostic tools under Diagnostics. For information on Diagnostic tools, see page 7-11.
The Software Option Upgrade feature is used when installing a software or an accessory upgrade on the cardiograph. For information, see the PageWriter Trim Cardiograph Upgrade Instructions provided with the upgrade kit.
Setting the Default Paper Size The cardiograph is shipped configured for the common paper size for your country or region. The paper size can be changed in Configuration.
To change the default paper size:
1 Press down and hold the Alt key ( ) on the keyboard.
2 Press the S key. The System screen appears.
3 Press the Tab key ( ) or turn the Trim Knob until the A or A4 setting under Paper Size is highlighted.
NOTE A4 paper requires a special paper drawer modification. Contact the nearest Philips Response Center for more information, see page 1-38.
4 Press the space bar (on keyboard) or the Trim Knob to select a default paper setting.
Setting the Caps Lock Feature The cardiograph keyboard can be configured to type in all capital letters. When the feature is enabled, the icon appears on the Order entry and Patient ID screens.
Factory Default Settings
Paper Size (varies by region)
Caps Lock: Off
Lead standard (varies by region)
Default Display Format: 6x2
Battery Power Saving Modes:– Standby: On with Idle Timeout: 5 minutes– Shut Down: On with Idle Timeout: 10 minutes
Notification message: none
Simulated Data: Not enabled
2-24 PageWriter Trim Cardiograph Instructions for Use
![Page 83: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/83.jpg)
PageWriter Trim II and III Configuration System Settings
To enable the caps lock feature:
1 Press the Tab key ( ) or turn the Trim Knob until ON is highlighted under Caps Lock.
2 Press the space bar (on keyboard) to select the check box. With the check box selected ( ), the keyboard will type in all capital letters.
Printed ECG Lead StandardThe cardiograph can be configured to print ECGs with the AAMI or IEC lead standard. The R/T (real-time) ECG screen on the cardiograph will always display AAMI leads, regardless of the printed ECG setting.
To set the printed report lead standard:
1 Press the Tab key ( ) or turn the Trim Knob until the AAMI or IEC lead standard is highlighted.
2 Press the space bar (on keyboard) or the Trim Knob to set the default print lead standard.
Default Display Format SettingThe R/T (real-time) ECG screen can be configured to display a default 6x2 or 3x4, 1R lead configuration. Each time the cardiograph is shut down and restarted, the default display format appears.
NOTE The R/T ECG screen displays AAMI lead configuration in the 6x2 or 3x4, 1R format.
The lead format on the R/T ECG screen can be changed at any time during a patient session by pressing the up or down arrow key.
For more information on using the R/T ECG screen, see page 1-34, or see Chapter 3 “The Patient Session” of the PageWriter Trim Cardiograph Instructions for Use on the User Documentation CD, or download the file from the Philips InCenter web site (incenter.medical.philips.com).
To set the default display format setting:
1 Press the Tab key ( ) or turn the Trim Knob until the 6x2 or 3x4, 1R lead format is highlighted.
2 Press the space bar (on keyboard) to select the setting.
Battery Power Saving ModesThe Battery Power Saving Modes are used to specify the Standby and Shutdown features. Both features are fully configurable and are used to help prolong battery life between charges.
The Standby feature turns off the cardiograph display (screen is black) if the cardiograph is not used for a pre-set number of minutes. When the cardiograph is in Standby, the green Standby indicator light illuminates (left side of cardiograph). Standby can be entered on any cardiograph screen by pressing the On/Standby button. Press any key on the cardiograph to exit Standby. The cardiograph quickly returns to the previously viewed screen.
NOTE The cardiograph will not enter Standby if the Patient ID screen is open, or if the cardiograph is printing an ECG.
PageWriter Trim Cardiograph Instructions for Use 2-25
![Page 84: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/84.jpg)
PageWriter Trim II and III Configuration System Settings
The Shutdown feature is used to automatically shut down all cardiograph power if the cardiograph is not used for a pre-set number of minutes after entering Standby. The green Standby indicator light is not lit when the cardiograph is shut down. Press the On/Standby button to turn on the cardiograph. The cardiograph will restart and display a series of information screens before the R/T ECG screen appears.
NOTE The Shutdown feature may be disabled.
To set the battery power saving features:
1 Press the Tab key ( ) or turn the Trim Knob until the Idle Timeout (Minutes) field next to Standby is highlighted.
2 Enter the number of minutes (5-60) that elapse before the cardiograph enters Standby.
3 Press the Tab key or turn the Trim Knob until the Idle Timeout (Minutes) field next to Shutdown is highlighted.
NOTE To disable the Shutdown feature, press the Tab key or turn the Trim Knob until Shutdown is highlighted. Press the space bar (on keyboard) to clear the check box. The Shutdown feature is disabled.
4 Enter the number of minutes (10-3000) that pass after the cardiograph enters Standby that it automatically shuts down.
Select another tab (top of screen) to continue making changes. If done making changes, press the Enter key ( ) to save the changes and to exit the Configuration screen. The new changes are applied.
Setting the Notification Message Feature The cardiograph can be configured to display a customized message, instruction set, or other information each time that the cardiograph is returned to active use from Standby. The message can contain up to five individual lines of text, with each line up to fifty characters in length. The message displays on the R/T ECG screen until the user selects the OK button and closes the window.Figure 2-8 Sample Notification Message
To create a notification message:
1 Press the Tab key ( ) or turn the Trim Knob until the Add button under Notification Messages is highlighted.
2 Press the space bar (on keyboard) or the Trim Knob to select the button.
3 The Please input data window appears. Type in the first line of text to appear on the notification message screen. The information can be up to fifty characters in length.
2-26 PageWriter Trim Cardiograph Instructions for Use
![Page 85: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/85.jpg)
PageWriter Trim II and III Configuration System Settings
4 Press the Tab key or turn the Trim Knob until the OK button is highlighted.
5 Press the space bar or the Trim Knob to enter the line of text into the notification message.
6 Continue to add up to five total lines of text in the order that they should appear on the notification message window.
To delete a line of the notification message:
1 Press the Tab key ( ) or turn the Trim Knob until the drop-down list under Notification Messages is highlighted (in blue).
2 Press the space bar (on keyboard) or the Trim Knob to open the drop-down list. Press the up or down arrow key to scroll through the lines of text. Highlight the line of text to be deleted.
3 Press the space bar or the Trim Knob to close the drop-down menu.
4 Press the Tab key or turn the Trim Knob to highlight the Delete button.
NOTE The line of text is automatically deleted once the Delete button is selected. No confirmation message to delete is provided.
5 Press the space bar or the Trim Knob to delete the selected line of text from the notification message.
Simulated Waveform Data Feature The cardiograph can be configured to display simulated waveforms (no data is acquired from the Patient Interface Module). This simulated waveform display may be helpful when training users on cardiograph operation.
When simulated waveforms appear on the screen, the statement Simulated Data appears on the R/T ECG screen in the same location as the Patient ID number, see “PageWriter Trim II and III Status Bar” on page 1-33. No Patient ID information can be entered when simulated waveforms are displayed on the cardiograph.
Any ECG printed using simulated waveforms will include the statement Simulated data on the report in the same location as the Patient ID number.
To turn on simulated waveform data:
1 From any configuration screen, press down and hold the Alt key ( on the keyboard.
2 Press the S key. The System screen appears.
3 Press the Tab key ( ) or turn the Trim Knob until the ON check box under Simulated Data is highlighted.
4 Press the space bar (on keyboard) or the Trim Knob to select the check box. The simulated waveform feature is enabled.
5 To use the simulated waveform data feature immediately, press the Enter key ( ) to save the new configured setting.
6 Press and hold the On/Standby button for three seconds and then release it to shut down the cardiograph.
PageWriter Trim Cardiograph Instructions for Use 2-27
![Page 86: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/86.jpg)
PageWriter Trim II and III Configuration Order Settings
7 Remove the PIM from the PIM connector port on the rear of the cardiograph (see page 1-10).
8 Press the On/Standby button to restart the cardiograph. Simulated waveforms appears on the R/T ECG screen.
To turn off simulated waveform data:
1 From any configuration screen, press down and hold the Alt key ( ) on the keyboard.
2 Press the S key. The System screen appears.
3 Press the Tab key ( ) or turn the Trim Knob until the ON check box under Simulated Data is highlighted.
4 Press the space bar (on keyboard) or the Trim Knob to clear the check box. The simulated waveform feature is disabled.
5 Press the Enter key ( ) to save the new configured setting.
6 Press and hold the On/Standby button for three seconds and then release it to shut down the cardiograph.
7 Attach the PIM to the PIM connector port on the rear of the cardiograph (see page 1-10).
8 Press the On/Standby button to restart the cardiograph. The cardiograph returns to normal operation.
Order SettingsThe Order settings are used with the Orders feature on the cardiograph. The Quick Search Fields feature is used on the Patient ID entry screen. This feature is used to automatically locate a Pending Order from the Pending Orders list based on information entered into one searchable field. The field that is used to search for Pending Orders information is configurable.
The Delete After Selection feature is used to automatically delete an order after it is selected from the Pending Orders list on the Patient ID screen. Disabling this feature will allow an order to be selected multiple times from the Patient ID screen.
To configure the Order settings:
1 Press down and hold the Alt key ( ) on the keyboard.
2 Press the Q key. The Orders screen appears.
3 Under Quick Search Fields, the Patient ID field is selected as the searchable field. To select another field as the searchable field, press the down arrow key ( ) until the field is highlighted.
NOTE Ensure that the field enabled as the Quick Search Field is also enabled as an active Patient ID field on the cardiograph (see page 2-9).
4 Press the Tab key ( ) or turn the Trim Knob until the Delete After Selection text is highlighted.
ORDERS
2-28 PageWriter Trim Cardiograph Instructions for Use
![Page 87: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/87.jpg)
PageWriter Trim II and III Configuration Rhythm Settings
5 Press the space bar (on keyboard) or the Trim Knob to select or to clear the check box. With the check box selected, an order will be deleted from the Pending Orders list when it is selected during a patient session. With the check box cleared, the order may be selected multiple times from the Patient ID screen.
Select another tab (top of screen) to continue making changes. If done making changes, press the Enter key ( ) to save the changes and to exit the Configuration screen. The new changes are applied.
Rhythm SettingsThe Rhythm settings specify the default Rhythm report settings on the cardiograph. These settings include the size and the speed of the waveforms, and the individual leads that appear on the printed Rhythm report.
Any of the default settings may be changed during an individual patient session by selecting the Report button on the Command Toolbar and manually changing the Rhythm report settings.
NOTE To set Rhythm filter settings, see the next section “Filter Settings.”
To set default Rhythm settings:
1 Press down and hold the Alt key ( ) on the keyboard.
2 Press the V key. The Rhythm screen appears.
3 Press the Tab key ( ) or turn the Trim Knob until the drop-down list next to Speed (mm/s) is highlighted (in blue).
4 Press the space bar (on keyboard) or the Trim Knob to open the drop-down list.
5 Press the up or down arrow key ( ) to scroll through the available settings.
6 Press the space bar or the Trim Knob to select a setting.
7 Repeat the procedure to set the Size (mm/mv) and Size (V Leads) settings.
NOTE The Size (V Leads) setting scales the size of the precordial leads to one-half or to the same (full) size as the limb leads.
8 Press the Tab key or turn the Trim Knob to highlight the Select All check box to select all twelve leads to print on the Rhythm report. Or, press the Tab key or turn the Trim Knob to highlight the I lead check box. Press the up or down arrow key or turn the Trim Knob to select individual leads from the list. Press the space bar or the Trim Knob to select an individual lead check box.
Select another tab (top of screen) to continue making changes. If done making changes, press the Enter key ( ) to save the changes and to exit the Configuration screen. The new changes are applied.
REPORT
PageWriter Trim Cardiograph Instructions for Use 2-29
![Page 88: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/88.jpg)
PageWriter Trim II and III Configuration Rhythm Settings
Filter SettingsThe filter settings specify the default filter settings that are used for each patient session. The configurable filter settings include:
AC filter
Artifact filter
Baseline Wander filter
High and Low Pass Frequency filters
Figure 2-9 The Filter Settings on the Status Bar
About the Artifact and Baseline Wander Filters
The Artifact and Baseline Wander filters are optional filters that may be enabled or disabled. These optional filters are enabled or disabled by selecting the Filter button on the Command Toolbar, see page 1-34.
The purpose of the Artifact filter is to remove skeletal muscle artifact from ECG signals. Skeletal muscle artifact is one of the most difficult noise sources to eliminate due to the fact that it contains the same frequencies as actual ECG signals. The Artifact filter will eliminate skeletal muscle artifact, but will also reduce all high frequency components of the ECG signal.
A Artifact Filter
B Baseline Wander Filter
C AC Filter
D High and Low Pass Frequency Filters
A B C
D
FILTER
2-30 PageWriter Trim Cardiograph Instructions for Use
![Page 89: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/89.jpg)
PageWriter Trim II and III Configuration Rhythm Settings
The Baseline Wander filter helps to suppress the slow drifting of the ECG signal during ECG recording. Baseline wander may result from patient respiration or from other sources.
About High and Low Pass Frequency Filter Settings
The 0.5 Hz High Pass frequency filter setting provides the highest level of baseline wander suppression
The 0.15 Hz High Pass frequency filter setting provides a moderate amount of baseline wander suppression (suitable for most ECGs) without distorting the ST segment
The 0.05 Hz High Pass frequency filter setting provides the highest fidelity signal with the least amount of baseline wander suppression
The 40 Hz Low Pass frequency filter setting provides the maximum amount of noise suppression at low fidelity
The 100 Hz Low Pass frequency filter setting provides a moderate amount of noise suppression while providing accurate waveform representation
The 150 Hz Low Pass frequency filter setting provides the highest fidelity with a minimal amount of high-frequency noise suppression
For more information on using filters, see "Using Filters" on page 3-11.
Table 2-7 Artifact and Baseline Wander Filter Settings
Artifact and Baseline Wander Filters Enabled
Artifact and Baseline Wander Filters Disabled
Factory Default Settings
Artifact (F) Filter: On
High Pass (Hz) Frequency: 0.15
Low Pass (Hz) Frequency: 150
AC Filter (~): On
Rhythm Settings:– High Pass (Hz) Frequency: 0.15– Low Pass (Hz) Frequency: 150– Artifact (F) Filter: On
PageWriter Trim Cardiograph Instructions for Use 2-31
![Page 90: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/90.jpg)
PageWriter Trim II and III Configuration Rhythm Settings
To configure filters:
1 Press and hold the Alt key ( ) on the keyboard.
2 Press the F key. The Filter screen appears.
3 Press the Tab key ( ) or turn the Trim Knob to highlight the Filter On setting.
4 Press the space bar (on keyboard) or the Trim Knob to select the check box (if not selected). Selecting this check box turns on the optional filters (Artifact, Baseline Wander or both) for all patient sessions.
5 The Main Settings section specifies the optional filters and high and low pass frequency filter settings used for all Auto ECGs. Press the Tab key or turn the Trim Knob to highlight the optional filters (Artifact, Wander, or both) that are turned on for all patient sessions.
6 Press the space bar or the Trim Knob to select the filter setting.
7 Press the Tab key or turn the Trim Knob to highlight a High Pass and Low Pass frequency setting that is used for all patient sessions.
TIP The High and Low Pass frequency settings of 0.15 and 150 Hz are recommended for most ECGs.
8 Press the space bar or the Trim Knob to select a setting.
9 Press the Tab key or turn the Trim Knob to highlight the On check box under AC Filter (Hz) (bottom of screen).
10 Press the space bar or the Trim Knob to select the On check box.
NOTE Clear the On check box to turn off the AC filter.
Setting Default Rhythm Filter Settings
Rhythm reports require a separate set of filter settings. The High and Low Pass frequency filters are automatically enabled for all Rhythm reports. The Artifact filter (F) is an optional filter that can be enabled during a patient session.
NOTE The 0.05 Hz High Pass Frequency setting is recommended for all Rhythm reports. This setting minimizes the potential for any ST segment distortion.
To set high and low pass frequency settings for rhythm reports:
1 Press the Tab key ( ) or turn the Trim Knob to highlight a High Pass (Hz) and Low Pass (Hz) frequency filter setting.
2 Press the space bar or the Trim Knob to select the setting. Select another tab (top of screen) to continue making changes. If done making changes, press the Enter key ( ) to save the changes and to exit the Configuration screen. The new changes are applied.
2-32 PageWriter Trim Cardiograph Instructions for Use
![Page 91: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/91.jpg)
PageWriter Trim II and III Configuration TraceMasterVue ECG Management System Remote Sites
TraceMasterVue ECG Management System Remote Sites
The Remote Sites feature on the cardiograph is used with the Philips TraceMasterVue ECG Management System. The Remote Sites settings are used to configure how TraceMasterVue Remote Sites receive ECGs from the cardiograph, or transmit ECGs to the cardiograph. ECG transmission to and from a Remote Site can be done with a modem, or with a network connection.
The following illustration provides an overview of how Auto ECGs can be transferred from the cardiograph to a TraceMasterVue ECG Management System.
For detailed information on configuring the PageWriter Trim cardiograph with a TraceMasterVue ECG Management System, see the Configuring Cardiograph and TraceMasterVue Communication Guide available for download from the Philips InCenter web site (incenter.medical.philips.com). For information on using the Philips InCenter web site, see page 1-4Figure 2-10 Transferring Auto ECGs from the cardiograph
PageWriter Trim Cardiograph Instructions for Use 2-33
![Page 92: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/92.jpg)
PageWriter Trim II and III Configuration TraceMasterVue ECG Management System Remote Sites
TraceMasterVue Remote Sites that are defined in Configuration appear in the Selected Archive drop-down list in the Archive. The Archive is used to transmit ECGs to and from the cardiograph, and to search the Remote Site for ECGs to print on the cardiograph using the Query feature.
For more information on using the Archive, see page 4-1.
Remote Site Fax and Modem Connection (USA and Canada only)The cardiograph supports fax transmission of hard copy (non-editable) ECGs and modem transmission of ECG data to a TraceMasterVue ECG Management System. The cardiograph uses a PCMCIA Card modem (optional feature, see page 1-23) that supports printing to Group 3 Fax machines, and supports Class 1 or 2 Fax modem protocol (USA and Canada only).
For information on compatible PCMCIA card modems used outside of the USA and Canada, contact the nearest Philips Response Center (see page 1-38) or your local distributor.
WARNING Never connect the PC card modem to a phone line when the cardiograph is connected to a patient.
To configure a remote site with fax transmission:
1 Insert the PC card modem into the PC card slot on the rear of the cardiograph before configuring the fax or modem connection (see page 1-21)
1 Press and hold down the Alt key ( ) on the keyboard.
2 Press the R key. The Remote Sites screen appears.
3 Press the Tab key ( ) or turn the Trim Knob to highlight Fax or Network (modem, LAN).
4 Press the space bar (on keyboard) or the Trim Knob to select the setting.
For Fax:1 Press the Tab key ( ) or turn the Trim Knob to highlight the Name: field. The cursor
appears in the field.
2 Type in up to forty numbers or letters to represent the name of the sender of each fax transmission.
3 Press the Tab key or turn the Trim Knob to highlight the Station ID field. The cursor appears in the field.
4 Type in up to forty numbers or letters.
5 Press the Tab key or turn the Trim Knob to highlight the Name field. The cursor appears in the field.
6 Type in up to forty numbers or letters to represent the name of the recipient of each fax transmission.
ARCHIVE
2-34 PageWriter Trim Cardiograph Instructions for Use
![Page 93: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/93.jpg)
PageWriter Trim II and III Configuration TraceMasterVue ECG Management System Remote Sites
7 Press the Tab key or turn the Trim Knob to highlight the Fax Number field. The cursor appears in the field.
8 Type in the receiving fax number.
9 Press the Tab key or turn the Trim Knob to highlight the drop-down list under Dialing Devices.
10 Press the space bar (on keyboard) or the Trim Knob to display the drop-down list.
11 Press the up or down arrow key ( ) to highlight the installed modem card.
NOTE If the installed modem card does not appear on the drop-down list, ensure that the modem card is fully inserted into the PC card slot on the rear of the cardiograph. If the card is not installed, or was not fully inserted into the slot, press and hold down the On/Standby button for three seconds, then release it. The cardiograph shuts down. Push the On/Standby button again. After the R/T ECG screen appears, follow the procedure “Opening the Configuration Screen” on page 2-2 and then return to this procedure.
12 Press the space bar to select the modem card.
13 Press the Tab key or turn the Trim Knob to highlight the Memo: field. The cursor appears in the field.
14 Type in optional memo text to appear on the fax cover sheet. A new Remote Site can be created using these settings, or any existing Remote Site may be saved with the new settings. Follow steps 15 to 18 to create a new Remote Site, or see the next procedure to edit an existing Remote Site.
15 At the top of the screen a check mark and the word Modified appears. Press the Tab key or turn the Trim Knob to highlight the Add New button.
16 Press the space bar or the Trim Knob. The Add New Remote Site window appears.
17 Type in a name for the Remote Site configured with these fax settings.
18 Press the Tab key or turn the Trim Knob to highlight the OK button.
19 Press the space bar or the Trim Knob. The new Remote Site with fax transmission is created. Select another tab (top of screen) to continue making changes. If done making changes, press the Enter key ( ) to save the changes and to exit the Configuration screen. The new changes are applied.
To change remote site fax settings:
1 Press the Tab key ( ) or turn the Trim Knob until the Remote Sites Archive drop-down list is highlighted.
2 Press the space bar (on keyboard) or the Trim Knob to display the drop-down list.
3 Press the up or down arrow key ( ) to scroll through the drop-down list.
4 Press the space bar or the Trim Knob to select a Remote Site.
5 Make all changes to the selected Remote Site on the screen.
PageWriter Trim Cardiograph Instructions for Use 2-35
![Page 94: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/94.jpg)
PageWriter Trim II and III Configuration TraceMasterVue ECG Management System Remote Sites
6 When all changes are complete, a check mark and the word Modified appears at the top of the screen.
7 Press the Tab key or turn the Trim Knob until the Save button is highlighted.
8 Press the space bar or the Trim Knob to save the new settings to the selected Remote Site. Select another tab (top of screen) to continue making changes. If done making changes, press the Enter key ( ) to save the changes and to exit the Configuration screen. The new changes are applied.
Remote Sites Network ConnectionThe cardiograph supports the following network connections for Remote Sites:
10/100-Base T Ethernet using a PCMCIA network LAN card (see page 1-23)
wireless LAN card (see page 1-22)
For more information on configuring network settings, see your Network Administrator.
For information on configuring the wireless LAN card option with the PageWriter Trim Cardiograph, see the PageWriter Trim Cardiograph Wireless LAN Installation Instructions on the User Documentation CD, or download the file from the Philips InCenter web site (incenter.medical.philips.com).
To configure a remote site with a network connection:
1 Press and hold down the Alt key ( ) on the keyboard.
2 Press the R key. The Remote Sites screen appears.
3 Press the Tab key ( ) or turn the Trim Knob to highlight Network (modem, LAN).
4 Press the space bar (on keyboard) or the Trim Knob to select the setting.
5 Press the Tab key or turn the Trim Knob to highlight the settings Receive (Query) and Copy/Transfer (left side of screen).
NOTE Selecting the Receive (Query) check box enables the user to search the Remote Site (in the Archive) for ECG files to print on the cardiograph. Selecting the Copy/Transfer check box enables the user to transfer ECGs from the Archive to a TraceMasterVue ECG Management System.
6 Under the Network tab (right of screen), press the Tab key or turn the Trim Knob to highlight the Server URL field. The cursor appears in the field.
7 Type in the URL address of the Remote Site server. The Server URL is the TraceMasterVue file server URL. The Server URL must be entered in the following format: http://computername/EMSCOMM/ Computername is the TraceMaster file server computer name or IP address. Examples of valid URLs include: http://tracemaster/EMSCOMM/ or http://10.101.2.42/EMSCOMM/.
8 Press the Tab key or turn the Trim Knob to highlight the User Name field. The cursor appears in the field.
2-36 PageWriter Trim Cardiograph Instructions for Use
![Page 95: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/95.jpg)
PageWriter Trim II and III Configuration TraceMasterVue ECG Management System Remote Sites
9 Type in the TraceMasterVue User Name.
10 Press the Tab key or turn the Trim Knob to highlight the Password field. The cursor appears in the field.
11 Type in the Password for the TraceMasterVue User Name.
12 Press and hold down the Alt key on keyboard.
13 Press the Z key. The Net Connect screen appears.
14 Press the Tab key or turn the Trim Knob to highlight Always Connected or Dial-up (modem) connection.
15 Press the space bar or the Trim Knob the select the setting.
For Dial-up Modem:1 Press the Tab key ( ) or turn the Trim Knob to highlight the Dialing Devices drop-
down list.
2 Press the space bar (on keyboard) or the Trim Knob to display the drop-down list.
3 Select the installed modem card.
NOTE If the installed modem card does not appear on the drop-down list, ensure that the modem card is fully inserted into the PC card slot on the rear of the cardiograph. If the card is not installed, or was not fully inserted into the slot, press and hold down the On/Standby button for three seconds, then release it. The cardiograph shuts down. Push the On/Standby button again. After the R/T ECG screen appears, follow the procedure “Opening the Configuration Screen” on page 2-2 and then return to this procedure.
4 Press the Tab key or turn the Trim Knob to highlight the Phone field. The cursor appears in the field.
5 Type in the dial-up modem telephone number.
6 Press the Tab key or turn the Trim Knob to highlight the User Name field. The cursor appears in the white box.
7 Type in the TraceMasterVue User Name for the dial-up modem connection.
8 Press the Tab key or turn the Trim Knob to highlight the Password field. The cursor appears in the field.
9 Type in the password for the TraceMasterVue user name.
10 Press the Tab key or turn the Trim Knob to highlight the Domain field. The cursor appears in the white box.
11 Type in the Domain name (optional).
12 At the top of the screen a check mark and the word Modified appears. Press the Tab key or turn the Trim Knob to highlight the Add New button.
13 Press the space bar or the Trim Knob. The Add New Remote Site window appears.
14 Type in a name for this Remote Site.
15 Press the Tab key or turn the Trim Knob to highlight the OK button.
PageWriter Trim Cardiograph Instructions for Use 2-37
![Page 96: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/96.jpg)
PageWriter Trim II and III Configuration Network Settings
16 Press the space bar or the Trim Knob. The Remote Site appears in the Remote Sites Archive drop-down list (top of screen) and may be selected in the Archive. Select another tab (top of screen) to continue making changes. If done making changes, press the Enter key ( ) to save the changes and to exit the Configuration screen. The new changes are applied.
Network SettingsThe settings in this section include network protocol settings used with the wireless LAN or the Ethernet LAN connection. The cardiograph supports the following network connections:
10/100-Base T Ethernet using a PCMCIA network card (see page 1-23)
wireless LAN card (see page 1-22)
The network configuration settings support TCP/IP using a static IP address or a DNS or WINS server.
For more information on configuring network settings, see your Network Administrator.
For information on configuring the wireless LAN card option with the PageWriter Trim Cardiograph, see the PageWriter Trim Cardiograph Wireless LAN Installation Instructions on the User Documentation CD, or download the file from the Philips InCenter web site (incenter.medical.philips.com).
For detailed information on configuring the PageWriter Trim cardiograph with a TraceMasterVue ECG Management System, see the Configuring Cardiograph and TraceMasterVue Communication Guide available for download from the Philips InCenter web site (incenter.medical.philips.com). For information on using the Philips InCenter web site, see page 1-4Figure 2-11 Connecting the LAN card
2-38 PageWriter Trim Cardiograph Instructions for Use
![Page 97: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/97.jpg)
PageWriter Trim II and III Configuration Network Settings
Networking OverviewThe PageWriter Trim cardiograph communicates with the TraceMasterVue ECG Management System through a network connection. In the cardiograph network configuration settings, all TCP/IP settings are configurable based on the specific needs of the clinical environment. Both DHCP (Dynamic Host Configuration Protocol) and fixed IP (Internet Protocol) address settings are available.
DHCP
With DHCP, the LAN automatically provides a dynamic IP address to the cardiograph. The LAN logs the cardiograph’s unique MAC (Media Access Control) address and provides a temporary DHCP IP address for the cardiograph.
If the cardiograph is connected to different LAN servers within the same facility, it may have to be reset in order to be recognized and assigned a DHCP IP address. Or, if the cardiograph has not been connected to the network for a specified period of time (defined by the LAN), the network may not recognize the cardiograph. In this case, the cardiograph may also have to be reset. Resetting the cardiograph at multiple locations on the LAN may be time consuming.
If the cardiograph is going to be connected to multiple sites within a facility, or to different LAN servers within a facility, it may be more efficient to assign the cardiograph a fixed IP address.
Fixed IP Address
Fixed IP addresses allow the cardiograph to be recognized throughout a network. With a fixed IP address, the cardiograph will be recognized at multiple locations throughout a LAN and will not require a full reset in order to be recognized. Using fixed IP addresses will also avoid the problem of having multiple IP addresses assigned to a single cardiograph.
Auto NegotiationWhen the cardiograph is connected to a LAN, it automatically configures the correct settings for Ethernet speed and mode (half or full duplex). If the auto-negotiation fails, it may be necessary to lock a specific switch or router port to a fixed setting (for example, 100BaseT Full Duplex) in order to obtain a connection.
Issues with the timing of the PageWriter Trim auto negotiation have been reported with certain CISCO switches (such as the CISCO 4506). To obtain a LAN connection with these switches, the specific LAN port may have to be locked down with fixed Ethernet port settings. The cardiograph should only be connected to these locked down ports.
For more information on networking options or to troubleshoot specific networking issues, consult your network administrator.
To configure cardiograph network settings:
1 Press and hold down the Alt key ( ) on the keyboard.
2 Press the N key. The Network screen appears.
3 Under Network ID, press the Tab key ( ) or turn the Trim Knob to highlight the text field next to Computer Name (if not highlighted).
PageWriter Trim Cardiograph Instructions for Use 2-39
![Page 98: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/98.jpg)
PageWriter Trim II and III Configuration Password Settings
4 Type in the computer name for the cardiograph (up to sixteen letters or numbers).
NOTE The Computer Name may not contain spaces.
5 Press the Tab key or turn the Trim Knob to highlight the Obtain IP Address Automatically (DNS) or Specify IP Address (fixed IP address) setting depending on your network requirements.
6 Press the space bar or the Trim Knob to select the setting.
For Fixed IP address:1 Press the Tab key ( ) or turn the Trim Knob to select the IP Address, Subnet Mask,
and Default Gateway fields. A cursor appears in the white box. Type in the IP address information for each field.
2 Press the Tab key or turn the Trim Knob to select the Primary DNS Server or Primary WINS fields. The cursor appears in the white box.
3 Type in the server information.
4 Press the Tab key or turn the Trim Knob to select the Secondary DNS or Secondary WINS fields (if necessary).
5 Type in the server information.
6 To apply the new network settings the cardiograph must restart. Press the Enter key ( ) on keyboard to save the settings.
7 Press and hold the On/Standby button for three seconds and then release the button. The message PageWriter Trim is shutting down... appears. The cardiograph shuts off.
8 Press the On/Standby button to restart the cardiograph. The cardiograph restarts and the new network settings are applied.
Password SettingsThe following cardiograph features can be configured to be password access controlled:
Archive
Configuration
Passwords can be up to six letters or numbers in length and are case-sensitive (capital and lower case letters can be used). The Password Configuration System password must be configured first. This password controls access to all password settings on the Configuration screens. Entering a correct password allows the user to change all password settings on the cardiograph. The Archive password must be entered to open the Archive screen. The Configuration password must be entered to open the Configuration screens.
To configure passwords:
1 Press and hold down the Alt key ( ) on keyboard.
2 Press the W key. The Passwords screen appears. The Password Configuration System password needs to be configured first.
2-40 PageWriter Trim Cardiograph Instructions for Use
![Page 99: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/99.jpg)
PageWriter Trim II and III Configuration Locale Settings
3 Press the Tab key ( ) or turn the Trim Knob until the first field to the right of Password Configuration System (under the Enter Password column) is highlighted. The cursor appears in the field.
4 Type in a password (up to six letters or numbers in length).
5 Press the Tab key or turn the Trim Knob until the cursor appears in the second field (under the Confirm Password column).
6 Re-enter the password.
NOTE If the password is re-entered incorrectly, the message Invalid Password Entered appears. Push the Trim Knob to select OK. Re-enter the password.
7 Press the Tab key or turn the Trim Knob to highlight the On check box to the right of Password Configuration System (under the Enabled column).
8 Follow the same procedure to configure passwords for the Archive and Configuration features on the cardiograph.Select another tab (top of screen) to continue making changes. If done making changes, press the Enter key ( ) to save the changes and to exit the Configuration screen. The new changes are applied.
Lost PasswordsIf a cardiograph password is lost and cannot be retrieved, contact the nearest Philips Response Center for assistance, see page 1-38.
Locale SettingsThe settings in this section include setting time format, date format, numerical, and unit measurements for specific countries or regions.
To change the date and time:
1 Press the hold down the Alt key ( ) on the keyboard.
2 Press the L key. The Locale screen appears.
3 The Region: drop-down list is highlighted. Press the space bar (on keyboard) or the Trim Knob to display the drop-down list.
4 Press the up or down arrow key ( ) to scroll through the language and country selections.
5 Press the space bar to select a language and country setting. The settings for the specified language and country appear on the screen.
6 Any of the settings on the screen may be edited, if necessary. Select another tab (top of screen) to continue making changes. If done making changes, press the Enter key ( ) to save the changes and exit the Configuration screen. The new changes are applied.
PageWriter Trim Cardiograph Instructions for Use 2-41
![Page 100: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/100.jpg)
PageWriter Trim II and III Configuration Cardiograph Settings
Cardiograph SettingsThe optional settings in this section provide information about a specific cardiograph including: Location Code (LOC), Device ID (identification number to track a specific cardiograph), Institution Label, Institution Number, Facility Label, Facility Number, Department Label and Department Number.
Each of these fields may be customized with any thirty-two letters or numbers. Location Code (LOC) is limited to five numbers only.
Each of these configured information fields appear on the printed Auto ECG and are transferred with the ECG to a TraceMasterVue ECG Management System. To view examples of these information fields on the printed ECG report, see "Reading the Printed ECG Report" on page 5-1. The table below describes each cardiograph identification information field.
Table 2-8 Cardiograph Identification Information Fields
Cardiograph Identification Field Description
LOC (Location Code) Only used with a TraceMaster ECG Management System (version A.04.02 or higher)
Limited to five numbers in length
Does not appear on the printed ECG
Configuring this information field disables the Institution Number and Department Number fields
Device ID Appears on the printed ECG
Limited to thirty-two letters or numbers in length
Institution Label Appears on the printed ECG
Limited to thirty-two letters or numbers in length
Institution Number Appears on the printed ECG
Limited to thirty-two numbers or in length
Facility Label Appears on the printed ECG
Limited to thirty-two letters or numbers in length
Facility Number Appears on the printed ECG
Limited to thirty-two numbers in length
Department Label Appears on the printed ECG
Limited to thirty-two letters or numbers in length
Department Number Appears on the printed ECG
Limited to thirty-two numbers or length
2-42 PageWriter Trim Cardiograph Instructions for Use
![Page 101: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/101.jpg)
PageWriter Trim II and III Configuration Cardiograph Settings
To configure institution information
1 Under Identification, press the Tab key ( ) or turn the Trim Knob until the field next to Location Code is selected. The cursor appears in the field.
NOTE The Location Code (LOC) is only used with the Philips TraceMaster ECG Management System (version A.04.02 or higher) and does not appear on the printed 12-lead ECG. Configuring the LOC disables the Institution Number and Department Number fields. For more information see the Configuring TraceMasterVue and Cardiograph Communication Guide on the User Documentation CD, or download the file from the Philips InCenter web site (incenter.medical.philips.com).
2 Enter the Location Code.
NOTE The Location Code is limited to five numbers in length. The first three numbers are used to identify an institution number, and the last two numbers are used to identify a department number.
3 Press the Tab key or turn the Trim Knob to select the field next to Device ID. The cursor appears in the field.
4 Enter the number.
5 Press the Tab key or turn the Trim Knob to select the field next to Institution Label. The cursor appears in the field.
6 Enter the text.
7 Press the Tab key or turn the Trim Knob to select the field next to Institution Number. The cursor appears in the field.
8 Enter the number.
9 Press the Tab key or turn the Trim Knob to select the field next to Facility Label. The cursor appears in the field.
10 Enter the text.
11 Press the Tab key or turn the Trim Knob to select the field next to Facility Number. The cursor appears in the field.
12 Enter the number.
Factory Default Setting
No cardiograph information fields are entered
PageWriter Trim Cardiograph Instructions for Use 2-43
![Page 102: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/102.jpg)
PageWriter Trim II and III Configuration Cardiograph Settings
13 Press the Tab key or turn the Trim Knob to select the field next to Department Label. The cursor appears in the field.
14 Enter the text.
15 Press the Tab key or turn the Trim Knob to select the field next to Department Number. The cursor appears in the field.
16 Enter the number. Select another tab (top of screen) to continue making changes. If done making changes, press the Enter key ( ) to save the changes and to exit the Configuration screen. The new changes are applied.
Metronome Settings This section is also used to configure the Metronome feature. The Metronome is used with the Auto ECG function to perform exercise stress tests such as the Masters’ Two Step. Using this feature, the patient exercises at a rate indicated by the metronome chime, and an Auto ECG is taken after the patient stops exercising. The default settings for the Metronome are set in Configuration, but these settings may be changed by the user during a patient session.
For more information on using the Metronome feature during a patient session, see "Using the Metronome with Auto ECG" on page 3-27.
To set metronome settings:
1 Press the Tab key ( ) or turn the Trim Knob until the ON check box under Metronome is highlighted.
2 Press the space bar (on keyboard) or the Trim Knob to select the check box. Selecting the ON check box enables the Metronome feature. Each time the Auto button is pressed, the Metronome window appears on the screen.
3 Press the Tab key or turn the Trim Knob to highlight the field to the right of Number of Steps (under Speed). Type in the number of default steps (16-70) to be used with the Metronome feature during a typical stress test. This setting can be changed by the user during a patient session.
Factory Default Settings
Metronome
Set to Off
Number of Steps 50
Stress Test Protocol: Master Double
2-44 PageWriter Trim Cardiograph Instructions for Use
![Page 103: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/103.jpg)
PageWriter Trim II and III Configuration Cardiograph Settings
4 Press the Tab key or turn the Trim Knob to highlight a setting under Stress Test Protocol. This setting sets the default Masters’ Two Step stress test used with the Metronome. This setting can be changed by the user during a patient session.
5 Press the Tab key or the Trim Knob to select a Masters’ Two Step Stress Test setting.Select another tab (top of screen) to continue making changes. If done making changes, press the Enter key ( ) to save the changes and to exit the Configuration screen. The new changes are applied.
Magnetic Card Reader Settings This section also sets the default Patient ID field settings for the optional magnetic card reader, see page 1-26 for more information.
TIP Ensure that the selected Patient ID fields (see page 2-8) and the Patient ID fields selected for the magnetic card reader are consistent.
The magnetic card reader supports the following standards:
ISO 7810, 7811-1, -2, -3, -4, -5
JIS X 6301 and X 6302
To configure the magnetic card reader:
1 Press the Tab key ( ) or turn the Trim Knob until the Field 1 drop-down list under Magnetic Card Reader - Track 1 is highlighted.
2 Press the space bar (on keyboard) or the Trim Knob to display the drop-down list of available Patient ID information fields.
3 Press the up or down arrow key ( ) to scroll through the drop-down list.
4 Press the space bar or the Trim Knob to select a Patient ID field.
Table 2-9 Masters’ Two Step Stress Test Settings
Test Description
Master Single Patient exercises for 90 seconds
Master Double Patient exercises for 180 seconds
Factory Default Settings
Magnetic Card Reader:– Field 1: Patient ID (number)– Fields 2, 3, 4: no fields selected (None).
PageWriter Trim Cardiograph Instructions for Use 2-45
![Page 104: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/104.jpg)
PageWriter Trim II and III Configuration Saving Configured Settings
5 Repeat the procedure for Fields 2-4. Select another tab (top of screen) to continue making changes. If done making changes, press the Enter key ( ) to save the changes and to exit the Configuration screen. The new changes are applied.
Saving Configured SettingsAll cardiograph configured settings may be saved as a configuration settings file to a PC card or to a USB memory stick, and then uploaded to multiple cardiographs. Use this feature when configuring multiple cardiographs with the same settings.
Select all of the default cardiograph configuration settings before saving them to a PC card or to a USB memory stick as a configuration file.
NOTE Network settings are not saved with the configuration settings file. It is recommended to print out a configuration settings report to capture a record of all network settings on the cardiograph, see page 2-48.
TIP It is recommended to save cardiograph configuration settings to a PC card or to a USB memory stick in case of system failure.
To save configuration settings to a PC card:
1 Select all cardiograph configured settings to be saved to the configuration settings file.
2 Insert the PC card into the PC card slot, or insert the USB memory stick into the USB port on the rear of the cardiograph.
3 Press the Tab key ( ) or turn the Trim Knob to highlight the Config button on the Command Toolbar.
4 Press the space bar (on keyboard) or the Trim Knob to select the button. The Configuration screen appears.
5 Press and hold down the Alt key ( ) on the keyboard.
6 Press the S key. The System screen appears.
7 Press the Tab key or turn the Trim Knob until the Save Configuration File button under Configuration Management is highlighted.
8 Press the space bar or the Trim Knob. The Save Configuration File window appears.
9 The Select Destination Media drop-down list is highlighted. Press the up or down arrow key to select the output media.
10 Press the Tab key or turn the Trim Knob to select the Input file name: field.
11 Type in a name for the configuration settings file.
12 Press the Tab key or turn the Trim Knob until the OK button is highlighted.
CONFIG
2-46 PageWriter Trim Cardiograph Instructions for Use
![Page 105: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/105.jpg)
PageWriter Trim II and III Configuration Loading the Configuration Settings File
13 Press the space bar or the Trim Knob to select the button.A message appears that the configuration settings file is saved to the selected media. The Configuration screen automatically closes. The configuration settings file may be uploaded to additional cardiographs using the following procedure.
Loading the Configuration Settings File If the cardiograph loses all configured settings, upload the cardiograph configuration settings file to the cardiograph using a PC card or USB memory stick.
This procedure may also be used when loading cardiograph configuration settings onto multiple cardiographs.
NOTE Network settings are not saved with the configuration settings file. It is recommended to print out a configuration settings report to capture a record of all network settings on the cardiograph, see page 2-48.
To load the configuration settings file onto the cardiograph:
1 Insert the PC card or the USB memory stick that contains the configuration settings file into the PC card slot or the USB port on the rear of the cardiograph.
2 From the R/T ECG screen, press the Tab key ( ) or turn the Trim Knob to select the Config button on the Command Toolbar.
3 Press the space bar (on keyboard) or the Trim Knob to select the button. The Configuration screen appears.
4 Press and hold down the Alt key ( ) on the keyboard.
5 Press the S key. The System screen appears.
6 Press the Tab key or turn the Trim Knob until the Load Configuration File button under Configuration Management is highlighted.
7 Press the space bar or the Trim Knob. The Load Configuration File window appears. The Select Input Source pull-down list is highlighted.
8 Press the up or down arrow key ( ) to select the input media. Press the space bar to select the input media. The configuration settings file(s) saved to the input media display under Profiles List.
9 Press the Tab key or turn the Trim Knob to highlight a profile under Profiles List. Press the space bar or the Trim Knob to select the configuration settings file.
10 Press the Tab key or turn the Trim Knob to highlight the OK button. Press the space bar or the Trim Knob to select the button.The configuration settings file is loaded onto the cardiograph. The new settings are applied.
CONFIG
PageWriter Trim Cardiograph Instructions for Use 2-47
![Page 106: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/106.jpg)
PageWriter Trim II and III Configuration Restoring Factory Default Configuration Settings
Restoring Factory Default Configuration SettingsThe factory default settings on the cardiograph can be restored at any time. Ensure that before reverting to factory default settings that any custom configuration settings are saved to a PC card or to a USB memory stick (see page 2-46).
To restore factory default configuration settings:
1 From the R/T ECG screen, press the Tab key ( ) or turn the Trim Knob to select the Config button on the Command Toolbar.
2 Press the space bar (on keyboard) or the Trim Knob to select the button. The Configuration screen appears.
3 Press and hold down the Alt key ( ) on the keyboard.
4 Press the S key. The System screen appears.
5 Press the Tab key or turn the Trim Knob until the Reset to Default button under Configuration Management is highlighted.
6 Press the space bar or the Trim Knob. The Configuration Management window appears with the message Are you sure you want to reset to factory settings? Press the space bar or the Trim Knob to select the Yes button.
NOTE Select the No button to not apply the factory default settings and to exit the window.
7 The message System reset to factory default settings appears. The factory default configuration settings are loaded onto the cardiograph.
Printing the Configuration Settings ReportA report that lists all of the configured settings information for the cardiograph may be printed from the Configuration screen. This report does include all TraceMasterVue Remote Site and network configuration settings.
To print a configuration settings report:
1 From the R/T ECG screen, press the Tab key ( ) or turn the Trim Knob to select the Config button on the Command Toolbar.
2 Press the space bar (on keyboard) or the Trim Knob to select the button. The Configuration screen appears.
3 Press and hold down the Alt key ( ) on the keyboard.
4 Press the S key. The System screen appears.
5 Press the Tab key or turn the Trim Knob until the Print Configuration File button under Configuration Management is highlighted. Press the space bar or the Trim Knob to select the button.
6 The Configuration Print Setup window appears. Press the Tab key or turn the Trim Knob until the Select Configuration Item drop-down list is highlighted. Press the space bar to open the drop-down list.
CONFIG
CONFIG
2-48 PageWriter Trim Cardiograph Instructions for Use
![Page 107: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/107.jpg)
PageWriter Trim II and III Configuration Printing the Configuration Settings Report
7 Press the up or down arrow key ( ) to select an individual item to print on the report, or specify Select All to print out all configured settings information. Press the space bar to select the printed report settings and to close the drop-down list.
8 Press the Tab key or the Trim Knob to highlight the OK button. Press the space bar or the Trim Knob to select the button. The configuration settings report prints.
PageWriter Trim Cardiograph Instructions for Use 2-49
![Page 108: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/108.jpg)
3
1The Patient Session
IntroductionA patient session is the period of time when waveform data is acquired and processed from a single patient. A patient session begins by entering accurate Patient ID information. Patient ID information is linked with all waveform data acquired during the patient session.
CAUTION Enter accurate and complete Patient ID information if using the Philips 12-Lead Algorithm to generate ECG interpretation. For more information see the Philips 12-lead Algorithm Physician’s Guide on the PageWriter Trim User Documentation CD, or download the file from the Philips InCenter web site (incenter.medical.philips.com). For information on using the Philips InCenter web site, see page 1-4.
The steps in a typical patient session are described below.
Table 3-1 The Patient Session
The Patient Session
Prepare the Patient
Step Description More Information See...
1 Prepare the patient for the procedure. “Patient Preparation” on page 3-2.
2 Prepare the electrode sites and attach the electrodes.
“Preparing the Skin” on page 3-3.
3 Attach the lead wires. “Attaching the Lead Wires” on page 3-7.
Enter Patient ID Information
Step Description More Information See...
1 Press the On/Standby button. “Using the On/Standby Button” on page 1-18.
2 Enter Patient ID information for the patient. “Entering Patient ID Information” on page 3-17.
Check the Signal Quality
Step Description More Information See...
1 Check the signal quality to ensure a quality ECG.
“Checking Signal Quality” on page 3-7.
3-1
![Page 109: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/109.jpg)
The Patient Session Patient Preparation
Patient PreparationFor complete information on patient preparation, proper electrode placement, and other patient preparation issues, see Lesson 2 of the PageWriter Trim Cardiograph Interactive Training Program on CD.
TIP Good ECG technique is very important to achieve the best quality results.
Instructing the PatientBefore attaching the electrodes, greet the patient and explain the procedure. Explaining the procedure decreases anxiety and informs the patient about what to expect.
Privacy is important to relaxation. When possible, take the ECG in a quiet room or area where others can’t see the patient. Draw the curtains around the bed when taking the ECG in a room with other people.
Reassure the patient that the procedure is painless.
Select an ECG Acquisition Mode
Step Description More Information See...
1 Do any of the following:
Print an Auto 12-lead ECG “Taking an Auto ECG” on page 3-25.
Print a Rhythm report “Rhythm ECG Acquisition” on page 3-28.
PageWriter Trim II and III only:
Print a 1-minute continuous report of one selected lead
“Disclose ECG Acquisition” on page 3-30.
End the Patient Session
Step Description More Information See...
1 Disconnect the patient and replace the PIM in its holder with the lead wires facing down.
“Inserting the PIM into the holder” on page 1-13.
The patient session ends when:
The On/Standby button is pressed
New Patient ID information is entered
The patient is disconnected or leads are off for more than 10 seconds
Table 3-1 The Patient Session (continued)
The Patient Session
3-2 PageWriter Trim Cardiograph Instructions for Use
![Page 110: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/110.jpg)
The Patient Session Patient Preparation
Make sure the patient is lying down and is comfortable. The patient’s arms and hands must be relaxed. If the table is too narrow, place the patient’s hands under the buttocks to prevent muscle tension in the arms.
Once the electrodes and lead wires are attached, instruct the patient to:
Remain still and do not talk
Breathe normally
Try not to shiver
Do not chew or clench teeth
The more relaxed the patient, the less the ECG will be affected by noise.
Preparing the SkinThorough skin preparation is very important. The skin is a poor conductor of electricity and frequently creates artifact that distorts the ECG signal. There is a natural resistance on the skin surface due to dry, dead epidermal cells, oils, and dirt.
To prepare the skin:
1 Shave hair from electrode sites if necessary (excessive hair prevents a good connection).
2 Wash thoroughly with soap and water.
3 Dry the skin vigorously to increase capillary blood flow to the tissues and to remove the dead, dry skin cells and oil.
TIP Do not use alcohol to clean the skin because it dries the skin. If there is no time to follow the procedure above, rub the site with gauze to remove dead, dry skin and to increase capillary flow.
Attaching the ElectrodesReview the male and female electrode placement diagrams in Figures 2-1 and 2-2 to ensure proper electrode placement.
WARNING Do not use disposable electrodes on more than one patient. Using disposable electrodes on multiple patients may cause infectious materials to be transferred between patients. Always discard disposable electrodes after patient use.
WARNING Always clean and disinfect reusable electrodes before patient use. See “Reusable Electrode Cleaning” on page 7-2 for information on cleaning and disinfecting reusable electrodes. Failure to properly clean and disinfect reusable electrodes may cause infectious materials to be transferred between patients.
PageWriter Trim Cardiograph Instructions for Use 3-3
![Page 111: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/111.jpg)
The Patient Session Patient Preparation
Review the following lead wire labeling and electrode placement information to ensure a quality ECG.Table 3-2 AAMI and IEC Lead Labeling and Electrode Placement
AAMI Lead IEC Lead Electrode Position
On the right leg (inside calf, midway between knee and ankle)
On the left leg (inside calf, midway between knee and ankle)
On the right arm (on the inside)
On the left arm (on the inside)
Right side of the sternum in the 4th intercostal space
Left side of the sternum in the 4th intercostal space
Midway between V2 and V4
Left midclavicular line in the 5th intercostal space
Anterior axillary line at the same level as V4, midway between V4 and V6
Left midaxillary line at the same level as V4
3-4 PageWriter Trim Cardiograph Instructions for Use
![Page 112: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/112.jpg)
The Patient Session Patient Preparation
Figure 3-1 Male 12-Lead Electrode Placement (AAMI/IEC)
V3/C3
V4/C4
V5/C5
V6/C6
LA/L
LL/FRL/N
RA/R
V1/C1
V2/C2
PageWriter Trim Cardiograph Instructions for Use 3-5
![Page 113: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/113.jpg)
The Patient Session Patient Preparation
Figure 3-2 Female 12-Lead Electrode Placement (AAMI/IEC)
To attach the electrodes:
1 Expose the arms and legs of the patient (to place the limb electrodes).
2 Place the electrodes on flat, fleshy parts of the arms and legs.
3 Place the electrodes on the inside of each arm (between the wrists and elbows).
4 Place the electrodes on the inside of each calf (between the knee and the ankle).
5 Place the limb electrodes equal distance from the heart. Position the electrodes at the same place on each limb.
V3/C3
V4/C4
V5/C5
V6/C6
LA/L
LL/FRL/N
RA/R
V1/C1
V2/C2
3-6 PageWriter Trim Cardiograph Instructions for Use
![Page 114: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/114.jpg)
The Patient Session Checking Signal Quality
6 For female patients, place the precordial electrodes on top of the breast (not underneath the breast tissue).
7 If a limb site is not available (amputation, injury) place the electrodes closer to the torso.
8 Attach the electrodes to the skin. A good test for firm electrode contact is to try to move it. If it moves easily, the electrode connection is too loose. Do not allow the electrodes to move in any way.
Attaching the Lead WiresEach lead wire tip is labeled and color-coded for easy identification.
To attach the lead wires:
Attach the lead wire to the corresponding electrode.
Checking Signal QualityReview Lesson 4 “Quality Assessment” of the PageWriter Trim Interactive Training Program on CD for complete information on signal quality assessment techniques to use with the PageWriter Trim cardiograph. This information is essential for taking quality ECGs each and every time.
Each PageWriter Trim cardiograph has built-in signal quality indicators that provide instant signal quality feedback. Be sure to check the signal quality indicators before printing the ECG.
Using the PageWriter Trim I Signal Quality IndicatorsThe signal quality indicators on this cardiograph include:
Heart beat detector
Leads off indicator
Signal quality indicator
Figure 3-3 PageWriter Trim I Signal Quality Indicators
A Heart Beat Detector C Signal Quality IndicatorB Leads off Indicator
A B C
PageWriter Trim Cardiograph Instructions for Use 3-7
![Page 115: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/115.jpg)
The Patient Session Checking Signal Quality
Heart Beat Detector
The heart beat detector icon ( ) appears on the LCD display when a patient heart beat is detected by the cardiograph. If the icon does not appear on the LCD display, check that the patient data cable on the PIM is securely attached to the PIM connector on the cardiograph (see page 1-12).
Leads Off Indicator
The leads off indicator displays the name of any loose or disconnected leads or electrodes.
Signal Quality Indicator
This feature displays the overall signal quality for all leads and electrodes. This indicator provides information on the amount of overall noise in the patient signal.
Table 3-3 Leads Off Indicators
Leads Off Code Indicates...
RL or N The RL or N electrode or lead wire are loose or disconnected
RL or N is the only lead wire or electrode connected
All twelve leads or electrodes are loose or disconnected
Two limb leads (I, II, III) are loose or disconnected
LL or F (left leg) LL or F electrode or lead wire are loose or disconnected
RA or R (right arm) RA or R electrode or lead wire are loose or disconnected
LA or L (left arm) LA or L electrode or lead wire are loose or disconnected
V1-6 or C1-6 One or more chest electrodes or lead wires are loose or disconnectedV13 or C13 indicates that electrodes or lead wires V1 and V3, or C1and C3 are loose
Table 3-4 Signal Quality Indicator
Symbol Indicates...
No symbol A good connection
* Slight noise or interference in signal
** Moderate noise or interference in signal
**** Extreme noise or interference
Lead wires or electrodes are disconnected
3-8 PageWriter Trim Cardiograph Instructions for Use
![Page 116: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/116.jpg)
The Patient Session Checking Signal Quality
Troubleshooting Signal Quality
For information on troubleshooting signal quality see:
“Using Filters” on page 3-11
See "Signal Quality" on page 6-14
Lesson 4 of the PageWriter Trim Interactive Training Program on CD
Using the PageWriter Trim II and III Signal Quality IndicatorsThe signal quality indicators on the PageWriter Trim II and III cardiographs include:
Leads off indicator
Color-coded waveforms (PageWriter Trim III only)
Preview screen
Using the Leads off indicator
The leads off indicator is located on the Status Bar.Figure 3-4 Leads off Indicator on Status Bar
The leads off indicator displays the name of any loose or disconnected leads or electrodes.
A Leads off indicator
Table 3-5 Leads Off Indicators
Leads Off Code Indicates...
RL or N The RL or N electrode or lead wire are loose or disconnected
RL or N is the only lead wire or electrode connected
All twelve leads or electrodes are loose or disconnected
Two limb leads (I, II, III) are loose or disconnected
LL or F (left leg) LL or F electrode or lead wire are loose or disconnected
RA or R (right arm) RA or R electrode or lead wire are loose or disconnected
LA or L (left arm) LA or L electrode or lead wire are loose or disconnected
RL 60~0.15 - 150 Hz P? ID:
NAME:
A
PageWriter Trim Cardiograph Instructions for Use 3-9
![Page 117: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/117.jpg)
The Patient Session Checking Signal Quality
Color-coded waveforms
PageWriter Trim III only
When the lead wires are attached to the patient, color-coded waveforms appear on the main R/T (real-time) ECG screen. The color of the waveform indicates the ECG signal quality.
V1-6 or C1-6 One or more chest electrodes or lead wires are loose or disconnectedV13 or C13 indicates that electrodes or lead wires V1 and V3, or C1and C3 are loose
Table 3-5 Leads Off Indicators (continued)
Leads Off Code Indicates...
Table 3-6 Color-coded Waveform Quality Indicators
Waveform Color Indicates... Possible Causes
Green waveform Good connection
Yellow waveform Moderate noise level, artifact, electrical interference, or a poor electrode connection12-lead ECG report quality will be affected
Inadequate patient preparationElectrical interference from another deviceModerate patient movement, tense patientImproperly gelled electrode (dried gel)
Orange Waveform Severe noise, artifact, electrical interference, or a very poor electrode connection12-lead ECG report quality will be significantly affected
Inadequate patient preparationSignificant electrical interference from another deviceSevere patient movementVery poorly gelled electrode (dried gel)
Red dotted line Loose electrode connectionECG waveform data that cannot be analyzed
Inoperative electrode, electrode that has fallen off the patientDefibrillation has been performed too recently to take ECG measurementsOther cause that renders waveform data useless
3-10 PageWriter Trim Cardiograph Instructions for Use
![Page 118: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/118.jpg)
The Patient Session Using Filters
Troubleshooting Signal Quality
For information on troubleshooting signal quality see:
“Using Filters” on page 3-11
Table 6-8 on page 6-10
Lesson 4 of the PageWriter Trim Interactive Training Program on CD
Using FiltersFilter settings may be configured on all models of the PageWriter Trim cardiograph. Filters can be used when all other troubleshooting methods to reduce signal quality problems are not successful. Before using filters:
Check patient and skin preparation techniques.
Ensure that the patient is comfortable, lying still, and breathing normally.
Check that the electrodes are correctly placed on the patient and are adhering to the skin.
Check if any surrounding devices are causing electrical interference. Switch any surrounding devices to battery power.
Filters should be applied only after all other potential causes of interference do not resolve a signal quality problem. The filter settings are displayed on the cardiograph and are also printed on the bottom of the ECG report inside the Filter Box. Figure 3-5 The Filter Box on the printed 12-lead ECG report
A Filter Box
Table 3-7 Filter Symbols
Filter symbol Description
F Artifact Filter
60 ~ AC Filter
A
PageWriter Trim Cardiograph Instructions for Use 3-11
![Page 119: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/119.jpg)
The Patient Session Using Filters
Artifact Filter
The Artifact filter removes skeletal muscle artifact. This noise source is the most difficult to eliminate because it contains the same frequencies as ECG signals. The Artifact filter eliminates skeletal muscle artifact, but also reduces all high frequency components of the ECG signal.
Figure 3-6 Artifact Filter symbol on the printed ECG report
Baseline Wander FilterBaseline wander is the slow drifting of the ECG baseline up or down during ECG recording. Baseline wander may result from patient respiration or from other sources.
NOTE With the Baseline Wander filter turned on, the High Pass Frequency Filter automatically sets to 0.5.
Figure 3-7 Baseline Wander Filter Symbol on the printed ECG report
Frequency Response FiltersThese filters suppress frequencies at the high and low ends of the ECG signal spectrum. The available low frequency response filter settings are 40, 100, and 150 Hz. Changing the low frequency filter to 40 or 100 Hz results in a smoother-looking ECG waveform while eliminating some fine detail in the signal. Small deflections, notches, and slurs may become distorted or may disappear if one of these filters is applied.Figure 3-8 Frequency Response Filter Symbol on the printed ECG report
0.05 High Pass Frequency Filter
150 Low Pass Filter Setting
Table 3-7 Filter Symbols (continued)
Filter symbol Description
3-12 PageWriter Trim Cardiograph Instructions for Use
![Page 120: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/120.jpg)
The Patient Session Using Filters
About High and Low Pass Frequency Filter Settings
The 0.5 Hz High Pass frequency filter setting provides the highest level of baseline wander suppression
The 0.15 Hz High Pass frequency filter setting provides a moderate amount of baseline wander suppression (suitable for most ECGs) without distorting the ST segment
The 0.05 Hz High Pass frequency filter setting provides the highest fidelity signal with the least amount of baseline wander suppression
The 40 Hz Low Pass frequency filter setting provides the maximum amount of noise suppression at low fidelity
The 100 Hz Low Pass frequency filter setting provides a moderate amount of noise suppression while providing accurate waveform representation
The 150 Hz Low Pass frequency filter setting provides the highest fidelity with a minimal amount of high-frequency noise suppression
Changing Filter Settings on the PageWriter Trim IThe following filters are available on the PageWriter Trim I cardiograph:
AC
Artifact
High and Low Pass Frequency
All filter settings used in a patient session are shown on the LCD display.Figure 3-9 Filter settings on the LCD Display
A Filter settings
Table 3-8 Filter symbols on the LCD Display
Filter symbol Description
F Artifact Filter
~ AC Filter
0.05 High Pass Frequency Filter
150 Low Pass Filter Setting
A
PageWriter Trim Cardiograph Instructions for Use 3-13
![Page 121: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/121.jpg)
The Patient Session Using Filters
To change the AC filter setting:
1 Turn the Trim Knob until the ~ symbol is highlighted.
2 Press the Trim Knob. A new screen appears with the current AC filter setting (50Hz, 60Hz, 0) highlighted.
3 Push the Trim Knob to change the setting.
NOTE Press the Stop button on the Control Panel to exit the screen without changing the AC filter setting.
4 Turn the Trim Knob to scroll through the available settings.
NOTE Selecting 0 turns off the AC filter.
5 Press the Trim Knob to select the setting.
6 Turn the Trim Knob to highlight the arrow ( ).
7 Press the Trim Knob to save the setting and to exit the screen. The new setting is applied.
To change other filter settings:
1 Turn the Trim Knob until the filter setting to be changed is highlighted.
2 Push the Trim Knob.
3 Turn the Trim Knob to scroll through the available filter settings.
4 Push the Trim Knob to select a setting.
5 Turn the Trim Knob to change additional filter settings.
NOTE The Artifact filter (F) may be turned on or turned off. No symbol appears on the LCD display when the Artifact filter is turned off.
NOTE When the High Pass Frequency Filter is set to 0.5 the Baseline Wander filter (W) is automatically turned on.
Changing Filter Settings on the PageWriter Trim II and IIIThe following filters are available on the PageWriter Trim II and III cardiographs:
AC
Artifact
Baseline Wander
High and Low Pass Frequency
All filter settings used in a patient session are shown on the Status Bar.
3-14 PageWriter Trim Cardiograph Instructions for Use
![Page 122: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/122.jpg)
The Patient Session Using Filters
Figure 3-10 Filter settings on the Status Bar
There are two sets of configured filters available on the PageWriter Trim II and III cardiographs: Main Settings and Rhythm Settings. These filters are applied to both the printed ECG report and to the real-time waveforms that display on the R/T ECG screen. These filter settings may only be changed in Configuration, see page 2-30 for more information.
The table below describes these filter settings.
A Filter settings
Table 3-9 Filter symbols on the Status Bar
Filter symbol Description
F Artifact Filter
W Baseline Wander Filter
60~ AC Filter
0.15 High Pass Frequency Filter
150 Low Pass Filter Setting
Table 3-10 Filter Settings
Filter Setting Description
Main Settings These filter settings are applied to all Auto and Disclose Reports
These filter settings may only be changed in Configuration
These filter settings include: High and Low Pass Frequency, Artifact, and Baseline Wander
The Artifact and Baseline Wander filters may be turned on or turned off for individual patient sessions; the High and Low Pass Frequency filters are turned on for all patient sessions
These filter settings can be applied to the real-time waveform display on the R/T ECG screen
A
RL F W 60~0.15 - 150 Hz P? ID:
NAME:
PageWriter Trim Cardiograph Instructions for Use 3-15
![Page 123: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/123.jpg)
The Patient Session Using Filters
The AC filter may be configured to be turned on or turned off for all patient sessions. The AC frequency Hertz is also set in Configuration (see page 2-30).
Artifact and Baseline Wander Filters
During a patient session, the Artifact and Baseline Wander filters (if configured) may be turned on or turned off.
To turn on or to turn off the artifact or baseline wander filter:
1 Press the Tab key ( ) or turn the Trim Knob to highlight the Filter button on the Command Toolbar.
2 Press the space bar or the Trim Knob. The Filter window appears.
NOTE Press the Esc key on keyboard to exit the Filter window without changing filter settings.
3 Press the Tab key or turn the Trim Knob to highlight the Filter On text under Report Filter.
4 Press the space bar or the Trim Knob to select the setting. With the check box selected, the Artifact and Baseline Wander filters are enabled. Clear the check box to turn off the Artifact and Baseline Wander filters.
5 Press the Enter key ( ) on keyboard to save the filter settings and to exit the window. The Artifact Filter (F) or Baseline Wander (W) symbol appear on the Status Bar, and the new filter settings are applied.
NOTE When the High Pass Frequency Filter is set to 0.5 the Baseline Wander filter (W) is automatically turned on.
Display Filter Settings
The Display Filter settings are applied to the real-time waveforms that appear on the R/T ECG screen. The Main Settings or Rhythm Settings may be applied to the waveforms on the R/T ECG screen.
Rhythm Settings These filter settings are used for all Rhythm reports
These filter settings may only be changed in Configuration
These filter settings include Artifact, and High and Low Pass Frequency
The Artifact filter may be turned on or turned off for individual patient sessions
These filter settings may be applied to the real-time waveform display on the R/T ECG screen
Table 3-10 Filter Settings
Filter Setting Description
FILTER
3-16 PageWriter Trim Cardiograph Instructions for Use
![Page 124: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/124.jpg)
The Patient Session Entering Patient ID Information
The Display Filter settings do not affect printed ECGs. The Main Settings are applied to printed Auto ECGs, and the configured Rhythm Settings are applied to printed Rhythm reports.
To change the display filter settings:
1 Press the Tab key ( ) or turn the Trim Knob to highlight the Filter button on the Command Toolbar.
2 Push the Trim Knob. The Filter window appears.
NOTE Press the Esc key on keyboard to exit the Filter window without changing filter settings.
3 Turn the Trim Knob to highlight Main Settings or Rhythm Settings under Display Filter.
4 Push the Trim Knob to select the setting.
5 Press the Enter key ( ) on keyboard to save the filter settings and to exit the window. The new filter settings appear on the Status Bar and are applied to the real-time waveforms on the R/T ECG screen.
NOTE The Rhythm Settings Low Pass Frequency filter setting will not appear on the R/T ECG screen. The Main Settings Low Pass Frequency setting will be applied.
NOTE When the High Pass Frequency Filter is set to 0.5 the Baseline Wander filter (W) is automatically turned on.
Entering Patient ID Information Patient ID information is very important and must be entered for each patient session.
CAUTION Enter accurate and complete Patient ID information if using the Philips 12-Lead Algorithm to generate ECG interpretation. For more information see the Philips 12-lead Algorithm Physician’s Guide on the PageWriter Trim User Documentation CD, or download the file from the Philips InCenter web site (incenter.medical.philips.com). For information on using the Philips InCenter web site, see page 1-4.
Entering Patient ID Information on the PageWriter Trim IThe PageWriter Trim I requires that Patient ID information be entered before printing an Auto ECG.
The following Patient ID information is entered on the PageWriter Trim I:
patient age
patient gender
Patient age may be entered in either adult and pediatric units.
To enter Patient ID information:
1 Press the Patient ID button on the Control Panel. The Patient ID entry screen appears.
2 The default age of 50 (years) is highlighted. Push the Trim Knob to change the patient age.
FILTER
PageWriter Trim Cardiograph Instructions for Use 3-17
![Page 125: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/125.jpg)
The Patient Session Entering Patient ID Information on the PageWriter Trim II and III
3 Turn the Trim Knob to highlight an age.
4 Push the Trim Knob to select the age.
5 Turn the Trim Knob to highlight the age unit, if necessary. The following age units are available.
6 Push the Trim Knob to select an age unit.
7 Turn the Trim Knob to highlight a patient gender icon ( female or male).
8 Push the Trim Knob to select the patient gender.
9 Turn the Trim Knob to highlight the arrow ( ).
NOTE Push the Stop button on the Control Panel to exit the Patient ID screen without saving the settings.
10 Push the Trim Knob to save the Patient ID settings and to exit the screen.
Entering Patient ID Information on the PageWriter Trim II and III
Patient ID information is very important and must be entered for each patient session.
CAUTION Enter accurate and complete Patient ID information if using the Philips 12-Lead Algorithm to generate ECG interpretation. For more information see the Philips 12-lead Algorithm Physician’s Guide on the PageWriter Trim User Documentation CD, or download the file from the Philips InCenter web site (incenter.medical.philips.com). For information on using the Philips InCenter web site, see page 1-4.
The amount and type of Patient ID information that appears on the Patient ID screen is configurable, see page 2-8 for more information. There are three main types of Patient ID information: patient information, clinical information, and order information. Patient ID information that is required to be complete before an Auto ECG can be transferred to a TraceMasterVue ECG Management System is also configurable, see page 2-9. Required Patient ID information appears in underlined type on the Patient ID screen.
Table 3-11 PageWriter Trim I Age Units
Age Unit Description
Y Years
M Months
W Weeks
D Days
H Hours
3-18 PageWriter Trim Cardiograph Instructions for Use
![Page 126: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/126.jpg)
The Patient Session Entering Patient ID Information on the PageWriter Trim II and III
Patient ID information is entered by:
Keyboard
Selecting a Pending Order
Barcode reader (optional)
Magnetic card reader (optional)
SmartCard reader (optional)
Entering Patient ID Information with the KeyboardTo enter Patient ID information with the keyboard:
1 Press the Patient ID button on the right side of the cardiograph. The Patient ID screen appears with the Patient Info. tab (top of screen) selected.
2 The ID field is selected. Enter the Patient ID number.
NOTE Patient ID information that is required to be complete in order to transfer an ECG to a TraceMasterVue ECG Management System is indicated in underlined type.
3 Press the Tab key ( ) or turn the Trim Knob to select the next field on the screen. Enter the information.
4 For Gender, press the Tab key or turn the Trim Knob to highlight the text. Press the space bar or the Trim Knob to select the patient gender.
5 If other tabs appear at the top of the screen (Clinical Info, Order Info), press and hold down the Alt key on the keyboard. Press the letter key in parenthesis on the tab. For example, to select the Clinical Info tab, press and hold down the Alt key, and then press the C key on the keyboard.
6 Continue to enter information on the screen.
7 When all Patient ID information has been entered, press the Enter key ( ) on the keyboard to save the information and to exit the screen. Press the Esc key on the keyboard to exit the screen without saving the Patient ID information.
NOTE A message appears if the Patient ID screen is exited before completing the required Patient ID information.
Opening a Pending OrderPending Orders consist of pre-loaded Patient ID information. This information is entered on the Orders screen using the cardiograph keyboard, or is loaded onto the cardiograph using a PC card, USB memory stick, or an Ethernet or wireless LAN connection. Once entered onto the cardiograph, these Pending Orders may be selected on the Patient ID screen.
For more information on using the Orders screen, see page 4-2.ORDERS
PageWriter Trim Cardiograph Instructions for Use 3-19
![Page 127: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/127.jpg)
The Patient Session Entering Patient ID Information on the PageWriter Trim II and III
To open a Pending Order:
1 Press the Patient ID button on the right side of the cardiograph. The Patient ID screen appears.
2 Press the Tab key ( ) or turn the Trim Knob to highlight the Orders button (top left of screen).
3 Press the space bar or the Trim Knob to select the button. The Select Pending Order window appears.
NOTE The Orders button only appears on the Patient ID screen when there are Pending Orders loaded on the cardiograph.
4 The available Pending Orders appear on the screen as a list. Press the up ( ) or down ( ) arrow key to highlight a Pending Order on the list.
5 The Select button (bottom of screen) is highlighted. Press the space bar or the Trim Knob to select the highlighted Pending Order. The Pending Order window closes and the Patient ID screen appears. The information from this Pending Order appears on the Patient ID screen.
NOTE A selected Pending Order may be configured to be deleted from the Pending Orders list, see page 2-28 for more information.
6 Enter any missing Patient ID information with the keyboard. Press the Tab key or turn the Trim Knob move between the different fields.
7 If other tabs appear at the top of the screen (Clinical Info, Order Info), press and hold down the Alt key on the keyboard. Press the letter key in parenthesis on the tab. For example, to select the Clinical Info tab, press and hold down the Alt key, and then press the C key on the keyboard.
8 When all Patient ID information has been entered, press the Enter key ( ) on the keyboard to save the information and to exit the screen. Press the Esc key on the keyboard to exit the screen without saving the Patient ID information.
NOTE A message appears if the Patient ID screen is exited before completing the required Patient ID information.
Using the Orders Quick Search Feature
The Quick Search feature is used to quickly search for a Pending Order by entering information into one Patient ID field. Any Pending Order that contains the same information in this specific Patient ID field is retrieved and displays on the Select Pending Order window.
The Patient ID field that is used to search for Pending Orders is specified in Configuration, see page 2-28 for more information.
To use the Quick Search feature to retrieve a pending order:
1 Enter information into the Patient ID field that is specified as the searchable field.
NOTE Only one Patient ID field can be specified as the searchable field, see page 2-28.
2 Press the Page button (right side of cardiograph). The Select Pending Order window appears with the retrieved Pending Order(s).
3-20 PageWriter Trim Cardiograph Instructions for Use
![Page 128: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/128.jpg)
The Patient Session Entering Patient ID Information on the PageWriter Trim II and III
3 The available Pending Orders appear on the screen as a list. Press the up ( ) or down ( ) arrow key to highlight a Pending Order on the list.
4 The Select button (bottom of screen) is highlighted. Press the space bar or the Trim Knob to select the highlighted Pending Order. The Pending Order window closes and the Patient ID screen appears. The information from this Pending Order appears on the Patient ID screen.
5 Enter any missing Patient ID information with the keyboard. Press the Tab key ( ) or turn the Trim Knob scroll through the different fields.
6 If other tabs appear at the top of the screen (Clinical Info, Order Info), press and hold down the Alt key on the keyboard. Press the letter key in parenthesis on the tab. For example, to select the Clinical Info tab, press and hold down the Alt key, and then press the C key on the keyboard.
7 When all Patient ID information has been entered, press the Enter key ( ) on the keyboard to save the information and to exit the screen. Press the Esc key on the keyboard to exit the screen without saving the Patient ID information.
NOTE A message appears if the Patient ID screen is exited before completing the required Patient ID information.
Entering Patient ID Information with the Barcode Reader The barcode reader is an optional cardiograph accessory available for purchase, see page 1-37. The barcode reader is used to automatically enter Patient ID information on the Patient ID screen by scanning a barcode. The barcode reader is shipped preconfigured for use with the PageWriter Trim cardiograph.
Attach the barcode reader to the barcode connector port ( ) on the rear of the cardiograph, see Figure 1-6 on page 1-9.
To enter Patient ID information with the barcode reader:
1 Press the Patient ID button on the right side of the cardiograph. The Patient ID screen appears. The ID field is highlighted.
2 Hold the barcode reader at a 45o angle over the barcode. The barcode automatically scans the information and it appears in the ID field. If the barcode does not automatically scan, press the button on the top of the scanner.
NOTE The barcode reader will only operate when held at a 45o angle.
3 Press the Tab key ( ) or turn the Trim Knob to highlight the next Patient ID field.
4 Hold the barcode reader at a 45o angle over the barcode. The barcode automatically scans. The information appears in the field.
5 Enter any missing information with the keyboard.
6 If other tabs appear at the top of the screen (Clinical Info, Order Info), press and hold down the Alt key on the keyboard. Press the letter key in parenthesis on the tab. For example, to select the Clinical Info tab, press and hold down the Alt key and then press the C key on the keyboard.
PageWriter Trim Cardiograph Instructions for Use 3-21
![Page 129: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/129.jpg)
The Patient Session Entering Patient ID Information on the PageWriter Trim II and III
7 When all Patient ID information has been entered, press the Enter key ( ) on the keyboard to save the information and to exit the screen. Press the Esc key on the keyboard to exit the screen without saving the Patient ID information.
NOTE A message appears if the Patient ID screen is exited before completing the required Patient ID information.
Entering Patient ID Information with the Magnetic Card ReaderThe magnetic card reader is an optional cardiograph accessory that is available for purchase, see page 1-26. The magnetic card reader is used to automatically enter up to four fields of Patient ID information by scanning a magnetic card. The four fields that are entered onto the Patient ID screen are configurable, see page 2-42.
Attach the magnetic card reader to the magnetic card reader port ( ) on the rear of the cardiograph, see page 1-26 for more information.
To enter Patient ID information with the magnetic card reader:
1 Press the Patient ID button on the right side of the cardiograph. The Patient ID screen appears.
2 Press the Tab key ( ) or turn the Trim Knob to highlight the MagCard button (top left of screen).
3 Press the space bar or the Trim Knob to select the button. The Magnetic Card Reader window appears.
4 Insert the magnetic card all the way into the slot. Leave the card in the slot for five seconds before removing it. The information scanned from the magnetic card appears on the screen.
5 The OK button (bottom of window) is highlighted. Press the space bar or the Trim Knob to select the OK button and to save the displayed Patient ID information. Press the Tab key ( ) or turn the Trim Knob to highlight the Cancel button if the Patient ID information did not scan correctly. Press the space bar or the Trim Knob to close the window. Repeat steps 2 through 5.
6 Enter any missing information with the keyboard.
7 If other tabs appear at the top of the screen (Clinical Info, Order Info), press and hold down the Alt key on the keyboard. Press the letter key in parenthesis on the tab. For example, to select the Clinical Info tab, press and hold down the Alt key and then press the C key on the keyboard.
8 When all Patient ID information has been entered, press the Enter key ( ) on the keyboard to save the information and to exit the screen. Press the Esc key on the keyboard to exit the screen without saving the Patient ID information.
NOTE A message appears if the Patient ID screen is exited before completing the required Patient ID information.
3-22 PageWriter Trim Cardiograph Instructions for Use
![Page 130: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/130.jpg)
The Patient Session Entering Patient ID Information on the PageWriter Trim II and III
Entering Patient ID Information with the SmartCard ReaderThe SmartCard reader is an optional cardiograph feature that is available for purchase (see page 1-26). The SmartCard reader is used to automatically enter up to two fields of Patient ID information (ID number and patient name) by scanning a SmartCard.
Attach the SmartCard reader to the USB connector ( ) on the rear of the cardiograph (see page 1-26).
To enter Patient ID information with the SmartCard reader:
1 Press the Patient ID button on the right side of the cardiograph. The Patient ID screen appears.
2 Press the Tab key ( ) or turn the Trim Knob to highlight the Smart Card button (top left of screen).
3 Press the space bar or the Trim Knob to select the button. The Smart Card Reader window appears.
4 Insert the SmartCard all the way into the slot. The scanned information appears on the screen in the ID: and Name: fields.
5 The OK button (bottom of window) is highlighted. Press the space bar or the Trim Knob to select the OK button and to save the displayed Patient ID information. Press the Tab key or turn the Trim Knob to highlight the Cancel button if the Patient ID information did not scan correctly. Press the space bar or the Trim Knob to close the window. Repeat steps 2 through 5.
6 Enter any missing information with the keyboard.
7 If other tabs appear at the top of the screen (Clinical Info, Order Info), press and hold down the Alt key on the keyboard. Press the letter key in parenthesis on the tab. For example, to select the Clinical Info tab, press and hold down the Alt key and then press the C key on the keyboard.
8 When all Patient ID information has been entered, press the Enter key ( ) on the keyboard to save the information and to exit the screen. Press the Esc key on the keyboard to exit the screen without saving the Patient ID information.
NOTE A message appears if the Patient ID screen is exited before completing the required Patient ID information.
Editing Patient ID Information Patient ID information may be edited at any time during the patient session, or may be edited after the patient session ends by editing the saved ECG in the Archive. The Archive provides temporary storage for ECGs until they are transferred to a TraceMasterVue ECG Management System. For more information on editing Patient ID information in the Archive, see page 4-13. A message appears if changes made to Patient ID information could affect ECG interpretation.
Changes to Patient ID information are applied to all ECGs taken during the current patient session.
PageWriter Trim Cardiograph Instructions for Use 3-23
![Page 131: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/131.jpg)
The Patient Session Emergency (STAT) ECGs
NOTE The magnetic card reader or Pending Orders cannot be used to edit existing Patient ID information. These buttons will not appear on the top of the Patient ID screen when editing existing Patient ID information.
To edit Patient ID information during the patient session:
1 Press the Patient ID button (right side of cardiograph).
2 The message Is this a New Patient? appears. Press the Tab key ( ) or turn the Trim Knob to highlight the No button.
3 Press the space bar or the Trim Knob to select the button. The Patient ID screen appears.
4 Edit the Patient ID information.
5 Press the Enter key ( ) on the keyboard to save the edits. Press the Esc key on keyboard to exit the screen without saving the edits.
Emergency (STAT) ECGsPatient ID information does not have to be entered in an emergency situation in order to take an Auto ECG. An emergency or STAT ECG can include a configurable STAT designation on the printed ECG, see page 5-10 for more information. A STAT pull-down list may be configured to appear on the Patient ID screen under the Order Info. tab. The STAT pull-down list is enabled in Configuration, see page 2-14.
Complete all Patient ID information after the emergency ECG is taken, but before the patient session ends. All required Patient ID information must be complete in order to transfer an Auto ECG to a TraceMasterVue ECG Management System, see page 4-9 for more information.
Taking a STAT ECG with the PageWriter Trim ITo take a STAT ECG:
1 Press the Auto button twice. The ECG prints.
2 Press the Auto button twice at any time to take another STAT ECG.
NOTE If interpretation is enabled on the cardiograph, and no Patient ID information is entered, a statement is included on the Auto ECG that interpretation used a default age (50 years) and gender (male).
Taking a STAT ECG with the PageWriter Trim II and IIITo take a STAT ECG:
1 Press the Auto button twice (right side of cardiograph).
2 The Auto ECG appears on the Preview screen. The ECG prints if the cardiograph is configured to automatically print Auto ECGs. If the Auto ECG does not automatically print, check the quality of the ECG on the Preview screen. If the quality is good, press the Enter key ( ) to print the ECG. Press the Copy button to print out an additional copy of the Auto ECG. Press the Esc key on keyboard to exit the Preview screen without printing
3-24 PageWriter Trim Cardiograph Instructions for Use
![Page 132: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/132.jpg)
The Patient Session Taking an Auto ECG
the ECG. Press the up ( ) or down ( ) arrow key to view the ECG in different report formats. Any of the displayed report formats may be printed by pressing the Enter key ( ).
3 On the R/T ECG screen, press the Auto button twice at any time to take another STAT ECG.
NOTE If no Patient ID information is entered, a statement is included on the Auto ECG that interpretation used a default age (50 years) and gender (male). The default age for interpretation is configurable (see page 2-9).
NOTE Patient ID information is required to transmit an Auto ECG from the Archive to a TraceMasterVue ECG Management System, see page 4-9 for more information.
Taking an Auto ECGThe Auto feature is used to quickly print a 12-lead ECG. The Auto ECG captures the most recent 10-seconds of waveform data. Follow the procedures below to take an Auto ECG.
Taking an Auto ECG with the PageWriter Trim I The following Auto 12-lead ECG formats are available on the PageWriter Trim I cardiograph:
3x4, 1R
6x2 (Cabrera lead sequence only)
On the 3x4, 1R ECG format, the Rhythm lead may be changed. To view sample reports of the available Auto ECG formats, see page 5-18.
To select an Auto report format:
1 Turn the Trim Knob to highlight the displayed ECG report format in the Format field. Push the Trim Knob. Turn the Trim Knob to highlight the 3x4 1R or 6x2 ECG format. Push the Trim Knob to select the ECG format.
NOTE The 6x2 ECG format is only available in Cabrera lead sequence.
2 To change the Rhythm lead for the 3x4, 1R format, turn the Trim Knob to highlight the Rhythm lead selected in the Leads field.
3 Push the Trim Knob.
4 Turn the Trim Knob to highlight the Rhythm lead to be selected for the ECG.
5 Push the Trim Knob to select the Rhythm lead.
To take an Auto ECG:
1 Press the Auto button on the Control Panel. The Patient ID entry screen appears.
2 Follow the procedure to enter Patient ID information, see page 3-17.The Auto ECG progress bar appears ( ) on the LCD display under the Leads-off field. The Auto ECG prints.
PageWriter Trim Cardiograph Instructions for Use 3-25
![Page 133: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/133.jpg)
The Patient Session Taking an Auto ECG
Taking an Auto ECG with the PageWriter Trim II and IIIThe Auto ECG captures the most recent 10-seconds of waveform data. When the Auto button is pressed, the Auto ECG appears on the Preview screen.
The Preview Screen
The Preview screen displays the waveforms of the Auto ECG exactly as they appear when printed. The waveforms on the Preview screen can be checked for normal quality indicators to ensure a quality ECG.
CAUTION Only the waveforms shown on the preview screen are an accurate representation of what is printed on the actual ECG. Interpretation, Patient ID, or other information may appear truncated or not appear at all on the ECG preview, but will appear on the printed ECG.
For information on ECG quality indicators, see Lesson 4 of the PageWriter Trim Interactive Training Program on CD.
TIP Reviewing Auto ECGs on the Preview screen before printing saves printer paper and ensures a quality ECG.
To take an Auto ECG:
1 On the R/T ECG screen, press the Auto button (right side of cardiograph). The Auto ECG displays on the Preview screen and prints (if the cardiograph is configured to do so).
2 Review the quality of the Auto ECG on the Preview screen. If the ECG quality is good, press the Enter key ( ) to print the ECG. If the ECG quality is poor, press the Esc key on keyboard to exit the Preview screen and not print the ECG.
3 Press the Copy button (right side of cardiograph) to print out a copy of the Auto ECG.
Changing Auto ECG Report Settings
The settings for the Auto ECG report may be changed at any time during a patient session. To review printed examples of the available Auto ECG formats, see page 5-18.
To change Auto ECG report settings:
1 Press the Tab key ( ) or turn the Trim Knob to highlight Report button on the Command Toolbar.
2 Press the space bar or the Trim Knob to display the Report settings window. The Auto tab (top of screen) is selected and the current Auto ECG report settings are displayed on the screen.
3 The Format: drop-down list is highlighted. Press the space bar or the Trim Knob to display the drop-down list of available Auto ECG formats.
NOTE The Pan-12 ECG format prints with Cabrera lead sequence and Time-Sequential acquisition. For more information, see page 5-24.
NOTE The 12x1 ECG format prints with Simultaneous acquisition. For more information, see page 5-22.
REPORT
3-26 PageWriter Trim Cardiograph Instructions for Use
![Page 134: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/134.jpg)
The Patient Session Taking an Auto ECG
WARNING Pace pulse tick marks do not appear on any PageWriter Trim II and III report that include simultaneous (not time-sequential) acquisition settings. For information on simultaneous acquisition, see page 5-13.
4 Press the up ( ) or down ( ) arrow key or turn the Trim Knob to highlight an Auto ECG format.
5 Press the space bar or the Trim Knob to select an Auto ECG format.
6 Continue to select Auto ECG settings by following the same procedure.
NOTE The Size (VLeads) selection sets the precordial leads to full or half the scale of the limb and augmented leads, see page 5-11.
For information on Pacer Detect settings, see page 3-31.
7 To save the new Auto ECG settings, press the Enter key ( ) on the keyboard. To exit the Auto ECG settings screen without saving the new settings, press the Esc key on the keyboard.
Using the Metronome with Auto ECG
PageWriter Trim II and III only
The cardiograph can be configured to automatically display the Metronome each time the Auto button is pressed. For more information, see page 2-42. A typical use of the Metronome is during a Masters’ Two-Step stress test: the patient exercises at a rate indicated by the metronome chime for a specified period of time, and then the cardiograph records an Auto ECG after the exercise session is complete.
The Metronome feature must be enabled in Configuration before it can be used with the Auto ECG feature. The procedure below is a recommend example of how to use the Metronome.
To use the Metronome feature:
1 Prepare the patient for the procedure.
2 Press the Patient ID button (right side of cardiograph) and enter the Patient ID information (see page 3-18).
3 Press the Auto button (right side of cardiograph). The Metronome window appears. The default Metronome settings appear on the screen. The displayed settings may be changed.
4 The Number of Steps field is highlighted. Type in the number of steps (16-70) that the patient will complete during the test.
5 Press the Tab key ( ) or turn the Trim Knob to select a setting under Stress Test Protocol. Highlight the Master Single (90 seconds) or Master Double (180 seconds) test.
6 Press the space bar or the Trim Knob to select a test setting.
7 Press the Tab key or turn the Trim Knob to highlight the Start button.
PageWriter Trim Cardiograph Instructions for Use 3-27
![Page 135: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/135.jpg)
The Patient Session Rhythm ECG Acquisition
8 When the patient is ready, press the space bar or the Trim Knob to start the Metronome. The Metronome beeps and the icon moves to indicate each time that the patient should take a step. The Metronome window displays the number of steps completed.A long beep indicates that the metronome cycle is complete. The message Timed ECG Test Completed appears at the top of the Metronome window.
9 To adjust the volume of the Metronome, press the Tab key or turn the Trim Knob to highlight the << or >> buttons. Press the space bar or the Trim Knob to lower or to raise the volume.
10 Connect the electrodes on the patient to the lead wires. Ensure that the lead wires are securely attached.
11 Press the Tab key or turn the Trim Knob to highlight Cancel button.
12 Press the space bar or the Trim Knob to close the Metronome window.The R/T ECG screen appears. The Auto ECG is acquired and appears on the Preview screen.
13 Review the quality of the Auto ECG on the Preview screen. If the ECG quality is good, press the Enter key ( ) to print the ECG. If the ECG quality is poor, press the Esc key on the keyboard to exit the Preview screen and not print the ECG. Press the Copy button to print out a copy of the last recorded ECG.
Rhythm ECG AcquisitionRhythm ECG acquisition is used to print continuous rhythm strips until the Stop button is pressed. Rhythm reports are not saved to the Archive and are not interpreted, see page 5-25 for more information.
Taking a Rhythm Report on the PageWriter Trim IRhythm reports may be printed with three or six preconfigured lead groups.
To select Rhythm report format and leads:
1 Turn the Trim Knob to highlight the displayed report format above Format (on the LCD display).
2 Push the Trim Knob to display the available report formats.
3 Turn the Trim Knob to highlight 3 (three lead) or 6 (six lead) Rhythm report.
4 Push the Trim Knob to select the Rhythm report format.
5 Turn the Trim Knob to highlight the displayed Rhythm leads above Leads.
3-28 PageWriter Trim Cardiograph Instructions for Use
![Page 136: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/136.jpg)
The Patient Session Rhythm ECG Acquisition
6 Push the Trim Knob to display the available preconfigured Rhythm lead groups.
7 Turn the Trim Knob to highlight a Rhythm lead group.
8 Push the Trim Knob to select the Rhythm lead group.
To record a Rhythm ECG:
1 Press the Rhythm button on the Control Panel.
2 The Patient ID entry screen appears. Enter the Patient ID information for the patient (see page 3-18).The Rhythm report progress bar appears ( ) on the LCD display under the Leads-off field. The Rhythm report prints.
3 Press the Stop button on the Control Panel to stop printing the Rhythm report.
4 Press the Page button on the Control Panel to advance the paper to the top of the next page.
Taking a Rhythm Report on the PageWriter Trim II and IIIRhythm reports may be printed with up to twelve selected leads. The leads that appear on the Rhythm report may be individually selected, and the size and speed of waveforms appearing on the report may also be selected.
To select Rhythm report leads:
1 Press the Tab key ( ) or turn the Trim Knob to highlight Report button on the Command Toolbar.
2 Press the space bar or the Trim Knob to display the Report settings window. Three tabs appear at the top of the screen.
3 To select the Rhythm tab, press and hold down the Alt key on the keyboard. Press the R key. The Rhythm screen appears.
4 Press the Tab key or turn the Trim Knob to highlight the Lead Groups button to select a preconfigured group of three or six leads.
5 Press the space bar or the Trim Knob to display the lead group list.
Table 3-12 Preconfigured Rhythm Lead Selections
Rhythm report Lead selections
3 lead report II-aVF-V2 (C2)
I-II-III
aVR-L-F (aVR, aVL, aVF)
6 lead report V1-V6 (C1-C6)
I-aVF (I, II, III, aVR, aVL, aVF)
REPORT
PageWriter Trim Cardiograph Instructions for Use 3-29
![Page 137: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/137.jpg)
The Patient Session Disclose ECG Acquisition
6 Press the up ( ) or down ( ) arrow key or turn the Trim Knob to scroll through the list.
7 Press the space bar or the Trim Knob to select a lead group. The selected leads appear on the screen under the Lead Groups button.
8 To select leads individually, press the up ( ) or down ( ) arrow key or turn the Trim Knob until the I lead on the lead list is highlighted.
9 Press the space bar or the Trim Knob to select the individual lead. The check box for that lead is selected.
10 Continue to select leads individually, or press the Tab key or turn the Trim Knob to highlight the Select All check box. Press the space bar or the Trim Knob to select all twelve leads.
To set the size and speed of waveforms:
1 On the Rhythm settings screen, press the Tab key or turn the Trim Knob to highlight the drop-down list under Speed.
2 Press the space bar or the Trim Knob to display the drop-down list.
3 Press the up ( ) or down ( ) arrow key or turn the Trim Knob to highlight a speed setting.
4 Press the space bar or the Trim Knob to select the speed setting.
5 Follow the same procedure to set the Size (mm/mV) and Size (V Leads) settings.
NOTE Size (V leads) sets the precordial leads to full or half the scale of the limb and augmented leads.
6 Press the Enter key ( ) on keyboard to save the Rhythm lead settings and to exit the screen. Press the Esc key to exit the screen without saving the settings.
To record a Rhythm ECG:
1 Press the Patient ID button (right side of cardiograph). Enter the Patient ID information for the patient.
2 Press the Rhythm button (right side of cardiograph). The Printing Rhythm Report progress window appears. The Rhythm report prints.
3 Press the Stop button (right side of cardiograph) to stop printing the Rhythm report.
4 Press the Page button (right side of cardiograph) to advance the paper to the top of the next page.
Disclose ECG AcquisitionPageWriter Trim II and III only
Disclose ECG acquisition prints a continuous 1-minute report of one selected lead. Disclose reports are not saved to the Archive and are not interpreted, see page 5-28 for more information.
3-30 PageWriter Trim Cardiograph Instructions for Use
![Page 138: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/138.jpg)
The Patient Session Pacing Detection Settings
To change the Disclose lead:
1 Press the Tab key ( ) or turn the Trim Knob to highlight Report button on the Command Toolbar.
2 Press the space bar or the Trim Knob to select the button. The Report settings window appears.
3 Three tabs appear at the top of the screen. To select the Disclose tab, press and hold down the Alt key on the keyboard and then press the D key. The Disclose screen appears.
4 The Lead drop-down list is highlighted. Press the space bar or the Trim Knob to display the drop-down list.
5 Press the up ( ) or down ( ) arrow key or turn the Trim Knob to highlight a lead.
6 Press the space bar or the Trim Knob to select the lead for the Disclose report.
To print a Disclose report:
1 Press the Tab key ( ) or turn the Trim Knob to highlight the Disclose button on the Command Toolbar.
2 Press the space bar or the Trim Knob to select the button.
3 The Printing Disclose Report progress window appears. The Disclose report prints.
Pacing Detection SettingsPageWriter Trim II and III only
The default Pacing Detection Setting displays on the Status Bar. This setting may be changed for an individual patient session. The default Pacing Detection Setting is specified in Configuration, see page 2-3 for more information. Figure 3-11 Pacing Detection Setting on the Status Bar
REPORT
DISCLOSE
A Pacing Detection Setting
RL 60~0.15 - 150 Hz P? ID:
NAME:
A
PageWriter Trim Cardiograph Instructions for Use 3-31
![Page 139: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/139.jpg)
The Patient Session Pacing Detection Settings
Pacemaker pulses that are detected by the cardiograph are marked on the Auto ECG with small vertical tick marks. These marks enable the overreader to identify false pacemaker pulse detections, or if true pulses are not being detected.
Table 3-13 Pacing Detection Settings
Setting Description Symbol on Status Bar
Not known if paced
This is the default setting and normally is used for both paced and non-paced patients
Pacemaker pulse detection is on and is at normal sensitivity
Occasional false pacemaker pulse detections may occur in ECGs with excessive noise
False detections may result in an incorrect interpretive statement appearing on the ECG
Small amplitude pacemaker pulses may not be detected using this setting
P?
Non-paced Pacemaker pulse detection is offUse this setting if there are false pacemaker pulse detections from noise, or if incorrect interpretive statements or inappropriate paced ECG complexes appear on the ECG
No code appears on the Status Bar if the Non-paced setting is selected
Paced Pacemaker pulse detection is on and is set at a higher sensitivityUse this setting if small amplitude pacemaker pulses are not being detected at the default (Not Known if Paced) settingFalse pacemaker pulse detections may occur if the ECG is noisy
P
3-32 PageWriter Trim Cardiograph Instructions for Use
![Page 140: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/140.jpg)
The Patient Session Getting Help on the Cardiograph
To change the pacing detection setting:
1 Press the Tab key ( ) or turn the Trim Knob to highlight Report button on the Command Toolbar.
2 Press the space bar or the Trim Knob to select the button. The Report settings window appears. Three tabs appear on the top of the screen. The Auto tab is selected.
3 Press the Tab key ( ) or turn the Trim Knob until the Not Known if Paced (recommended setting) is highlighted under Pacer Detect.
4 Press the up ( ) or down ( ) arrow key or turn the Trim Knob to highlight a setting.
5 Press the space bar or the Trim Knob to select the setting.
6 Press the Enter key ( ) to save the Pacing Detection Setting and to exit the screen. Press the Esc key to exit the screen and without saving the new setting.The new pacing detection setting is applied and appears on the Status Bar. After the patient session ends, the default pacing detection setting (set in Configuration) is restored and will appear on the Status Bar.
Getting Help on the CardiographPageWriter Trim II and III only
The Help button on the Command Toolbar may be selected at any time while using the cardiograph. Help provides basic information on cardiograph operation and on signal quality troubleshooting.
Paced (magnet) Use this setting if the ECG is acquired with an active pacemaker magnet or programmer in placePacemaker pulse detection is on and is at a higher sensitivityMagnets or programmers often put the pacemaker into a fixed-rate, non-sensing modeThe statement ECG ACQUIRED WITH MAGNET IN PLACE is printed on the 12-lead ECG notifying the overreader that a magnet or programmer was used and would explain the fixed rate behavior of the pacer
PM
Table 3-13 Pacing Detection Settings (continued)
Setting Description Symbol on Status Bar
REPORT
PageWriter Trim Cardiograph Instructions for Use 3-33
![Page 141: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/141.jpg)
The Patient Session Getting Help on the Cardiograph
To open Help:
1 Press the Tab key ( ) or turn the Trim Knob to highlight the Help button on the Command Toolbar.
2 Press the space bar or the Trim Knob to select the button.
3 The Help screen appears. Press the left ( ) or right ( ) arrow keys or turn the Trim Knob to go forward or backward through the screens. Press the Esc key on keyboard to exit the Help.
HELP
3-34 PageWriter Trim Cardiograph Instructions for Use
![Page 142: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/142.jpg)
4
1PageWriter Trim II and IIIOrders and Archive
About OrdersThe Order screen is used to pre-load Patient ID information onto the cardiograph. Orders are loaded onto the cardiograph using a PC card or a USB memory stick, or may be entered directly on the cardiograph using the keyboard. Once the Patient ID information is loaded onto the cardiograph, it becomes a Pending Order that may be selected on the Patient ID screen during a patient session. For more information, see page 3-19.
About the ArchiveThe Archive provides storage for Auto ECGs. Any Auto ECG stored in the Archive may be viewed and printed, and the Patient ID information may be edited and saved.
The Archive is also used to transmit Auto ECGs from the cardiograph to a TraceMasterVue ECG Management System by modem or by an Ethernet or wireless LAN network connection. Auto ECGs may also be transferred to any external ECG management system that accepts XML (Extensible Markup Language) files. For more information on the PageWriter Trim XML Schema, see page 1-3.
The Archive can also be used to search a configured TraceMasterVue Remote Site for stored 12-lead ECGs to view and print on the PageWriter Trim cardiograph. For information on configuring the cardiograph to work with Remote Sites, see page 2-33.
ORDER
ARCHIVE
4-1
![Page 143: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/143.jpg)
PageWriter Trim II and III Orders and Archive Using the Order Screen
Using the Order ScreenOrders are created, edited, deleted, and loaded onto the cardiograph from the Order screen.To open the Order screen:
1 Press the Tab key ( ) or turn the Trim Knob until the Order button on the Command Toolbar is highlighted.
2 Press the space bar or the Trim Knob to select the button. The Order screen appears.
Figure 4-1 The Order Screen
Table 4-1 Order Screen Description
Letter Description Function
A Patient ID Information tabs
The number of tabs that appear on the screen depends on the amount and type of Patient ID information configured for the cardiograph.
For information on configuring Patient ID information, see page 2-9.
To select a tab, press and hold down the Alt key on the keyboard. Press the letter key in parenthesis on the tab. For example, to select the Clinical Info. tab, press and hold down the Alt key and then press the C key.
B Patient ID columns These column headers list the Patient ID fields that are contained under each tab.
ORDER
ABC
D
E
F
4-2 PageWriter Trim Cardiograph Instructions for Use
![Page 144: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/144.jpg)
Using the Order Screen PageWriter Trim II and III Orders and Archive
C ID Complete check box This check box indicates that all required Patient ID information fields for the Order are complete.
Required Patient ID information is set in Configuration. For more information, see page 2-9.
D Available Space Information
Displays the number of loaded (pending) Orders on the cardiograph along with the number of Orders that may be loaded in the available space remaining on the cardiograph.
E Order List Lists all the pending Orders loaded onto the cardiograph.
These Orders have not yet been selected on the Patient ID screen during a patient session.
F Order Function Buttons Buttons that are used to navigate on the Order screen or are used to perform functions on the screen (see Table 4-2 below).
Table 4-2 Function Button Description
Button Select this button to...
Select Select an Order on the Order List
Select All Select all Orders displayed on the Order List
Add Order Manually add an Order to the Order List using the cardiograph keyboard
Edit Order Edit an Order on the Order List
Delete Order Delete an Order from the Order List
Load New Orders
Load Orders onto the cardiograph using a PC card or a USB memory stick
Table 4-1 Order Screen Description (continued)
Letter Description Function
PageWriter Trim Cardiograph Instructions for Use 4-3
![Page 145: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/145.jpg)
PageWriter Trim II and III Orders and Archive Entering New Orders
Entering New Orders Orders may be manually entered on the cardiograph using the keyboard.
To enter orders:
1 Press the Tab key ( ) or turn the Trim Knob to highlight the Add Order button (bottom of screen).
2 Press the space bar or the Trim Knob to select the button.The Please input data Patient ID window appears. The ID: field at the top of the screen is selected. The cursor appears in the field.
3 Type in the Patient ID information.
4 Press the Tab key or turn the Trim Knob to select the next field on the screen.
5 Type in the information. Repeat the procedure to complete all the Patient ID fields on the screen.
6 If additional tabs appear at the top of the screen, press and hold down the Alt key on the keyboard. Press the letter key in parenthesis on the tab. For example, to select the Clinical Info. tab, press and hold down the Alt key and then press the C key.
7 Enter the information on the additional tabs as required. Press the Tab key or turn the Trim Knob to move to the next field. Repeat to complete all the fields on the screens.To open a drop-down list, press the space bar or the Trim Knob. Press the up ( ) or down ( ) arrow key to highlight an item on the drop-down list, then press the space bar or Trim Knob to select it.
8 Press the Enter key ( ) to save the Order and to exit the screen. Press the Esc key to exit the screen without saving the Order.The Order screen appears. The new Order appears on the Order List and may be selected during a patient session (see page 3-19).
Deleting an Order Orders may be deleted at any time from the Order screen. One Order may be deleted, or multiple Orders may be deleted at the same time.
NOTE Deleted Orders may not be retrieved.
To delete an order:
1 Press the up ( ) or down ( ) arrow key to scroll through the Order list and to highlight an Order to be deleted. To select multiple Orders, press and hold down the Shift key ( ) and then press the up and down arrow key.
2 Once all Orders to be deleted have been selected on the list, press the Tab key ( ) or turn the Trim Knob to highlight the Select button (bottom of screen). Press the space bar or the Trim Knob. The Order(s) selected for deletion appear in dark gray on the Orders List.
4-4 PageWriter Trim Cardiograph Instructions for Use
![Page 146: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/146.jpg)
Editing an Order PageWriter Trim II and III Orders and Archive
3 Continue to select Orders to be deleted, or to delete all Orders from the list, turn the Trim Knob to highlight the Select All button. Push the Trim Knob to select the Select All button.
4 Press the Tab key or turn the Trim Knob to highlight the Delete Order button. Press the space bar or the Trim Knob to select the button. A message appears to confirm the deletion of the selected Orders. The OK button is highlighted. Press the space bar or the Trim Knob to confirm the deletion of the selected Order(s). Select the Cancel button to exit the window and not delete the selected Orders.
5 To remove Orders from the list to be deleted, press the up or down arrow key to highlight an Order. Press the Tab key or turn the Trim Knob to highlight the Unselect button. Press the space bar or the Trim Knob to select the button. Or, select the Unselect All button to deselect all orders.
Editing an Order An Order may be edited at any time from the Order screen.
NOTE Only one Order may be edited at a time.
To edit an order:
1 The Order to be edited must be highlighted in dark blue (or in dark gray) on the Order List. To highlight a different Order to be edited, press the up ( ) or down ( ) arrow key or turn the Trim Knob to scroll through the Order List.
2 Once the Order to be edited is highlighted in dark blue, press the Tab key ( ) or turn the Trim Knob to highlight the Edit Order button.
3 Press the space bar or the Trim Knob to select the button.
4 The Patient ID information for the Order appears on the screen. Edit the Patient ID information. If additional tabs appear at the top of the screen, press and hold down the Alt key on the keyboard. Press the letter key in parenthesis on the tab. For example, to select the Clinical Info. tab, press and hold down the Alt key and then press the C key.
5 Press the Enter key ( ) to save the edits to the Order and to exit the screen. Press the Esc key to exit the screen without saving the edits. The edited Order appears on the Orders list.
Loading Orders Orders may be loaded onto the cardiograph using a PC card or a USB memory stick. For information on the PC card and USB memory stick, see page 1-21.
To load orders:
1 Press the Tab key ( ) or turn the Trim Knob to highlight the Load New Orders button.
2 Press the space bar or the Trim Knob to select the button.
PageWriter Trim Cardiograph Instructions for Use 4-5
![Page 147: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/147.jpg)
PageWriter Trim II and III Orders and Archive Using the Archive
3 The Load New Orders window appears. Press the Tab key or turn the Trim Knob to highlight the Select Input Source drop-down list.
4 Press the space bar or the Trim Knob to open the drop-down list.
5 Press the up ( ) or down ( ) arrow key to highlight an input source.
6 Press the space bar or Trim Knob to select the input source.
7 Press the Tab key or turn the Trim Knob to select the dir\...\Filename.ext field. The cursor appears in the field. Type in the name of the Orders file contained on the PC card or USB memory stick.
8 Press the Tab key or turn the Trim Knob to highlight the OK button. Press the space bar or the Trim Knob to select the button. The Order(s) appear on the Orders List.
Using the Archive The Archive can be used for the following:
Print Auto ECGs (see page 4-9)
Transfer Auto ECGs to a TraceMasterVue ECG Management System using an Ethernet or wireless LAN network connection, or to a PC card or USB memory stick (see page 4-9)
Export Auto ECGs in XML format to an external data management system (see page 4-14)
Print a list of all of the Auto ECGs saved in a selected Archive (see page 4-14)
Search a TraceMasterVue Remote Site for Auto ECGs to print on the cardiograph (see page 4-14)
Delete Auto ECGs from the Archive (see page 4-16)
Saving Auto ECGs to the ArchiveThe Archive provides storage for Auto ECGs during a patient session. The cardiograph can be configured to automatically save Auto ECGs to the Archive (see page 2-23), or Auto ECGs can be manually saved to the Archive during a patient session.
Any Auto ECG saved to the Archive is saved to the Main Archive. The Main Archive can hold approximately 50 Auto ECGs (PageWriter Trim II) or 150 Auto ECGs (PageWriter Trim III). When the limit of 50 or 150 Auto ECGs has been reached, reports will have to be transferred and deleted from the Main Archive before more Auto ECGs can be saved. For information on deleting Auto ECGs from the Archive, see page 4-16.
4-6 PageWriter Trim Cardiograph Instructions for Use
![Page 148: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/148.jpg)
Opening the Archive Screen PageWriter Trim II and III Orders and Archive
There are two categories of Auto ECGs saved to the Main Archive: ID Complete and ID Incomplete.
Opening the Archive ScreenTo open the Archive screen:
1 Turn the Trim Knob until the Archive button on the Command Toolbar is highlighted.
2 Push the Trim Knob to select the button. The Archive screen appears.
Figure 4-2 The Archive Screen
NOTE XMT is an abbreviation for Transfer.
Table 4-3 ID Complete and ID Incomplete Auto ECGs
ID Complete ID Incomplete
All required Patient ID fields are complete
The Auto ECG can be transferred by modem, LAN, or wireless LAN to a or TraceMasterVue ECG Management System, or to a PC card or USB memory stick
Required Patient ID information is not complete
The Auto ECG cannot be transferred by modem, LAN, or wireless LAN to a or TraceMasterVue ECG Management System, or to a PC card or USB memory stick
ARCHIVE
A
DF
E
B
C
PageWriter Trim Cardiograph Instructions for Use 4-7
![Page 149: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/149.jpg)
PageWriter Trim II and III Orders and Archive Opening the Archive Screen
Table 4-4 Archive Screen Description
Letter Description Function
A Patient ID Information tabs
The number of tabs that appear on the screen are dependent upon the amount and type of Patient ID information configured for the cardiograph.
For information on configuring Patient ID information, see page 2-9.
To select a tab, press and hold down the Alt key on the keyboard. Press the letter key in parenthesis on the tab. For example, to select the Clinical Info. tab, press and hold down the Alt key and then press the C key.
B Patient ID columns These column headers list the Patient ID fields that are contained under each tab.
C Available Space Information
Displays the number of Auto ECGs in the Archive, along with the number of remaining Auto ECGs that may be saved in the available space left in the Archive.
D Selected Archive This drop-down list displays all of the available Archives.
The Main Archive is the internal cardiograph Archive.
E Archive Report List Displays all of the reports saved to the Selected Archive.
F Function buttons Buttons that are used to navigate on the Archive screen or are used to perform functions on the Archive screen (see Table 4-5 below).
Table 4-5 Archive Funtion Buttons Description
Button Select this button to...
Select Select a report
Select All Select all displayed reports
Edit Edit the Patient ID Information on the selected report
Delete Delete the selected report
Print/Preview View the selected Auto ECG on the Preview screen and to print the Auto ECG
4-8 PageWriter Trim Cardiograph Instructions for Use
![Page 150: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/150.jpg)
Transferring Auto ECGs to a TraceMasterVue ECG Management System PageWriter Trim II and III Orders and Archive
Transferring Auto ECGs to a TraceMasterVue ECG Management System
An Auto ECG must have all required Patient ID information complete before it can be transferred from the cardiograph to a TraceMasterVue ECG Management System. Auto ECGs are transferred using a configured modem or Ethernet or wireless LAN network connection, or with a PC card or USB memory stick.
For information on configuring a modem or LAN connection used to transfer Auto ECGs from the Archive, see page 2-36. For information on configuring the wireless LAN card, see the PageWriter Trim Cardiograph Wireless LAN Installation Instructions on the User Documentation CD, or download the file from the Philips InCenter web site (incenter.medical.philips.com). For information on using the Philips InCenter web site, see page 1-4.
All Auto ECGs that appear in the Main Archive-ID Complete Archive have complete Patient ID information and may be transferred. For more information on configuring required Patient ID fields, see page 2-9. Auto ECGs that have complete Patient ID information are marked with a selected check box under the ID Complete column.
Auto ECGs that are missing required Patient ID information do not appear in the Main Archive-ID Complete archive and may not be transferred. Complete all required Patient ID fields before transmitting the Auto ECG. For more information, see page 4-13.
Auto ECGs may be transferred one at a time, or multiple Auto ECGs in an Archive may be transferred at the same time.
Before transferring Auto ECGs, ensure that the modem, or network LAN or wireless LAN card is fully inserted into the PC card slot on the rear of the cardiograph. For more information, see page 1-21.
WARNING Do not connect the modem card to a phone line when the cardiograph is connected to a patient.
Transfer Transfer the selected report to a TraceMasterVue ECG Management System, or to a PC card or USB memory stick
Fax Fax the selected report
Archive Listing Print out a list of all reports in the selected Archive
Login WLAN Enter LEAP login name and password to access a configured wireless LAN network
Table 4-5 Archive Funtion Buttons Description (continued)
Button Select this button to...
PageWriter Trim Cardiograph Instructions for Use 4-9
![Page 151: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/151.jpg)
PageWriter Trim II and III Orders and Archive Viewing and Printing Auto ECGs in the Archive
To transfer an Auto ECG from the archive:
1 Press the Tab key ( ) or turn the Trim Knob to highlight the drop-down list under Selected Archive (bottom left of screen).
2 Press the space bar or the Trim Knob to open the drop-down list.
3 Press the up ( ) or down ( ) arrow key or turn the Trim Knob to highlight Main Archive-ID Complete.
4 Press the space bar or the Trim Knob to select the Archive. The Auto ECGs that can be transferred are displayed on the screen.
5 Press the up or down arrow key to scroll through the ECG list. To select multiple ECGs, press and hold down the Shift key ( ) and then press the up and down arrow key.
6 Once all ECGs to be transferred have been highlighted on the list, press the Tab key or turn the Trim Knob to highlight the Select button (bottom of screen). Press the space bar or the Trim Knob to select the button. The ECG(s) selected to be transferred appear in dark gray.
7 Continue to select ECGs to be transferred, or to transfer all ECGs on the list, press the Tab key or turn the Trim Knob to highlight the Select All button. Press the space bar or the Trim Knob to select the button.
8 Press the Tab key or turn the Trim Knob to highlight the Transfer button. Press the space bar or the Trim Knob to select the button. The Transfer Selected ECGs window appears.
9 Press the Tab key or turn the Trim Knob to highlight the drop-down list under Select Transfer Destination.
10 Press the space bar or the Trim Knob to display the drop-down list.
NOTE If selecting PC Card or USB Memory Stick, ensure that the media is fully inserted into the PC card slot or the USB port on the rear of the cardiograph. For more information, see page 1-21.
11 Press the up or down arrow key or turn the Trim Knob to highlight a transfer destination.
12 Press the space bar or the Trim Knob to select the transfer destination.
13 Press the Tab key or turn the Trim Knob to highlight the Delete Selected ECGs text. Selecting this option deletes the Auto ECG from the Main Archive and Main Archive-ID Complete archive after it is successfully transferred. Press the space bar or the Trim Knob to select the check box and to enable the feature.
14 Press the Tab key or turn the Trim Knob to highlight the OK button.
15 Press the space bar or the Trim Knob to transfer the Auto ECG(s). The Transfer Selected ECGs window appears and the Auto ECG(s) are transferred.
Viewing and Printing Auto ECGs in the Archive Any Auto ECG in an Archive can be viewed or printed on the cardiograph using the original report settings. A single Auto ECG may be viewed and printed, or multiple Auto ECGs in a selected archive may be viewed and printed.
4-10 PageWriter Trim Cardiograph Instructions for Use
![Page 152: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/152.jpg)
Faxing Auto ECGs in the Archive PageWriter Trim II and III Orders and Archive
To print an Auto ECG:
1 Press the Tab key ( ) or turn the Trim Knob to highlight the drop-down list under Selected Archive (bottom left of screen).
2 Press the space bar or the Trim Knob to open the drop-down list.
3 Press the up ( ) or down ( ) arrow key or turn the Trim Knob to highlight an Archive.
4 Press the space bar or the Trim Knob to select the Archive. The Auto ECGs contained in the selected Archive appear on the screen.
5 The Auto ECG selected to be viewed or printed appears highlighted in dark blue (or in dark gray) on the Report List. To select a different Auto ECG to be printed, press the up or down arrow key to highlight an ECG. To select multiple ECGs, press and hold down the Shift key ( ) and then press the up and down arrow key.
6 Once the Auto ECG(s) to be viewed and printed is highlighted, press the Tab key or turn the Trim Knob to highlight the Select button. Or, press the Tab key or turn the Trim Knob to highlight the Select All button to view and print all Auto ECGs in the Archive.
7 Press the space bar or the Trim Knob to select the button. The Auto ECG(s) to be printed are selected and appear on the Report List in light gray. To deselect an Auto ECG to be viewed and printed, press the up or down arrow key to highlight the ECG. To deselect multiple ECGs, press and hold down the Shift key and then press the up and down arrow key. Press the Tab key or turn the Trim Knob to highlight the Unselect button. Press the space bar or the Trim Knob to select the button. The Auto ECG is deselected and appears highlighted in dark blue (or in dark gray).
8 Once all Auto ECGs have been selected to be viewed and printed, press the Tab key or turn the Trim Knob to highlight the Print/Preview button.
9 Press the space bar or the Trim Knob to select the button. The Print Selected ECGs progress bar window appears. If the cardiograph is configured to automatically print, the ECG prints out. If the cardiograph is not configured to automatically print, the Auto ECG appears on the Preview screen. Press the up ( ) or down ( ) arrow key to change the report format of the displayed ECG. Press the Enter key ( ) to print out the ECG. Press the Esc key to exit the Preview screen and not print the ECG. If multiple Auto ECGs are have been selected, the next selected Auto ECG appears on the Preview screen.
NOTE For information on automatic print features, see page 2-23.
Faxing Auto ECGs in the Archive Any Auto ECG saved in the Archive can be faxed to a remote receiving station Site using the fax feature, see page 2-34 for more information. The fax feature requires that the removable modem card be fully inserted into the PC card slot located on the rear of cardiograph. For more information, see Figure 1-18 on page 1-23.
A single Auto ECG may be faxed, or multiple Auto ECGs may be faxed at the same time.
PageWriter Trim Cardiograph Instructions for Use 4-11
![Page 153: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/153.jpg)
PageWriter Trim II and III Orders and Archive Faxing Auto ECGs in the Archive
NOTE No guarantee is made as to the suitability of the faxed 12-lead ECG for any particular purpose, due to the variability inherent in fax technology.
WARNING Do not connect the modem card to a phone line when the cardiograph is connected to a patient.
To fax an Auto ECG:
1 Press the Tab key ( ) or turn the Trim Knob to highlight the drop-down list under Selected Archive (bottom left of screen).
2 Press the space bar or the Trim Knob to open the drop-down list.
3 Press the up ( ) or down ( ) arrow key or turn the Trim Knob to highlight an Archive.
4 Press the space bar or the Trim Knob to select the Archive. The Auto ECGs contained in the selected Archive appear on the screen.
5 The Auto ECG selected to be faxed appears highlighted in dark blue (or in dark gray) on the Report List. To select a different Auto ECG to be faxed, press the up or down arrow key to highlight an ECG. To select multiple ECGs, press and hold down the Shift key ( ) and then press the up and down arrow key.
6 Once the Auto ECG(s) to be faxed is highlighted, press the Tab key or turn the Trim Knob to highlight the Select button. Or, press the Tab key or turn the Trim Knob to highlight the Select All button to fax all Auto ECGs in the Archive.
7 A selected Auto ECG appears highlighted in light gray. To deselect an Auto ECG to be faxed, press the up or down arrow key to highlight the ECG. To deselect multiple ECGs, press and hold down the Shift key and then press the up and down arrow key. Press the Tab key or turn the Trim Knob to highlight the Unselect button. Press the space bar or the Trim Knob to select the button. The Auto ECG is deselected and appears highlighted in dark blue (or in dark gray).
8 Once all Auto ECGs have been selected to be faxed, press the Tab key or turn the Trim Knob to highlight the Fax button. The Fax Selected ECGs window appears.
9 Press the Tab key or turn the Trim Knob to highlight the drop-down list under Select Fax Destination.
10 Press the space bar or the Trim Knob to display the drop-down list.
11 Press the up or down arrow key or turn the Trim Knob to highlight the desired configured fax destination.
NOTE For information on configuring a Remote Site fax destination, see page 2-34.
12 Press the space bar or push the Trim Knob to select the highlighted fax destination.
13 Press the Tab key or turn the Trim Knob to highlight the OK button.
14 Press the space bar or the Trim Knob to fax the selected Auto ECG(s). The Fax Selected ECGs window appears and the Auto ECG(s) are faxed to the Remote Site.
4-12 PageWriter Trim Cardiograph Instructions for Use
![Page 154: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/154.jpg)
Editing Patient ID Information PageWriter Trim II and III Orders and Archive
Editing Patient ID Information Patient ID information may be edited or completed on any Auto ECG saved in the Archive. Edited Patient ID information (date of birth, gender, clinical information) may affect ECG interpretation and result in new interpretive, reason, and severity statements appearing on the Auto ECG.
NOTE Only one Auto ECG may be edited at a time.
To edit Patient ID information:
1 Press the Tab key ( ) or turn the Trim Knob to highlight the drop-down list under Selected Archive (bottom of screen).
2 Press the space bar or the Trim Knob to open the drop-down list.
3 Press the up ( ) or down ( ) arrow key or turn the Trim Knob to highlight an Archive.
4 Press the space bar or the Trim Knob to select the Archive. The Auto ECGs contained in the selected Archive appear on the screen.
5 The Auto ECG selected to be edited appears highlighted in dark blue (or in dark gray) on the Report List. To select a different Auto ECG to be edited, press the up or down arrow key to highlight an ECG.
6 Press the Tab key or turn the Trim Knob to highlight the Edit button.
7 Press the space bar or the Trim Knob to select the button. The Get Selected ECGs progress bar window appears, and then the Patient ID screen appears for the selected Auto ECG. The ID field is selected.
8 Edit the Patient ID information as required. Press the Tab key or turn the Trim Knob to move between the different Patient ID fields.
9 If additional tabs appear at the top of the screen, press and hold down the Alt key on the keyboard. Press the letter key in parenthesis on the tab. For example, to select the Clinical Info. tab, press and hold down the Alt key and then press the C key.
10 When done, press the Enter key ( ) to save the edited Patient ID information and to exit the screen. Press the Esc key to exit the screen without saving the edits to the Patient ID information.
11 If patient age (date of birth), gender, or clinical information is edited, the message Patient Data Changes will cause ECG to be reinterpreted appears. Press the space bar or the Trim Knob to select the OK button. The new Patient ID information is saved with the Auto ECG, and the interpretive, reason, and severity statements (if configured) may change.
PageWriter Trim Cardiograph Instructions for Use 4-13
![Page 155: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/155.jpg)
PageWriter Trim II and III Orders and Archive Exporting 12-lead Reports in XML Format
Exporting 12-lead Reports in XML FormatAuto ECGs may be transferred to an external data management system as an XML (Extensible Markup Language) file. Information on the Philips 12-lead ECG XML Schema and other XML utilities and tools is available on the Philips InCenter web site (incenter.medical.philips.com), see page 1-3 for more information. For information on accessing the Philips InCenter web site, see page 1-4.
CAUTION The PageWriter Trim cardiograph only supports the importing of XML files from the PageWriter Trim or PageWriterTouch cardiographs. Do not import XML files from other devices.
Printing a List of Auto ECGs in the Archive The cardiograph can print multiple page reports that list all of the Auto ECGs saved to an individual Archive. This printed report includes a listing of all Auto ECGs saved to the Archive, the date and time that each report was acquired, transmission information, and Patient ID information for each report including ID number, patient last name, date of birth, and gender.
To print a list of Auto ECGs:
1 Press the Tab key ( ) or turn the Trim Knob to highlight the drop-down list under Selected Archive (bottom of screen).
2 Press the space bar or the Trim Knob to open the drop-down list.
3 Press the up ( ) or down ( ) arrow key or turn the Trim Knob to highlight an Archive.
4 Press the space bar or the Trim Knob to select the Archive. The Auto ECGs contained in the selected Archive appear on the screen.
5 Press the Tab key or turn the Trim Knob to highlight the Archive Listing button (bottom of screen).
6 Press the space bar or the Trim Knob to select the button. The message Printing Archive Report appears and the report prints.
Searching a TraceMasterVue Remote Site A configured TraceMasterVue Remote Site can be searched for Auto ECGs to save to the cardiograph and to print on the cardiograph. All Auto ECGs saved to the cardiograph from a Remote Site are saved to the Remote Sites Archive. The Remote Sites Archive is selected from the Selected Archive drop-down list.
For information on configuring the cardiograph for use with a TraceMasterVue Remote Site, see page 2-33.
4-14 PageWriter Trim Cardiograph Instructions for Use
![Page 156: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/156.jpg)
Searching a TraceMasterVue Remote Site PageWriter Trim II and III Orders and Archive
Searching a Remote Site with the Wildcard CharacterWhen searching a Remote Site, the wildcard character (%) can be used to perform the broadest search possible using minimal information. The wildcard character used is the percentage sign (%). For example, to search for all Auto ECGs of patients with the last name of Smith, enter Smith% into the Patient Name field. This command will search the specified Remote Site for all Auto ECGs of patients with the last name Smith.
To search a remote site for Auto ECGs:
1 Press the Tab key ( ) or turn the Trim Knob to highlight the drop-down list under Selected Archive (bottom of screen).
2 Press the space bar or the Trim Knob to open the drop-down list.
3 Press the up ( ) or down ( ) arrow key or turn the Trim Knob to highlight the Remote Site Archive.
4 Press the space bar or the Trim Knob to select the Archive. The Auto ECGs contained in the selected Archive appear on the screen.
5 Press the Tab key or turn the Trim Knob to highlight the Get ECGs (Query) button (bottom of screen).
6 Press the space bar or the Trim Knob to select the button. The Remote Sites Query window appears.
7 Press the Tab key or turn the Trim Knob to highlight the Selected Remote Site drop-down list.
8 Press the space bar or the Trim Knob to display the drop-down list.
9 Press the up or down arrow key or turn the Trim Knob to highlight a configured Remote Site.
10 Press the space bar or the Trim Knob to select the Remote Site.
11 Press the Tab key or turn the Trim Knob to select the OK button.
12 Press the space bar or the Trim Knob to select the button. The Search screen appears.
13 Press the Tab key or turn the Trim Knob to highlight the fields under Query (Wildcard = %) at the bottom of the screen. Type in the search information using as many fields as necessary. The wildcard character (%) may be used.
NOTE If only the wildcard character is entered into a search field, all 12-lead ECGs saved to the Remote Site will be retrieved. Up to 100 ECGs may display in the Results window.
NOTE If no information is entered into a search field, that field will not be used to search the Remote Site.
14 Press the Tab key or turn the Trim Knob to highlight the Search button.
15 Press the space bar or the Trim Knob to select the button. The Remote Site Search progress bar window appears. After the search is complete, the ECGs that match the entered search information appear on the screen under Search Results.
16 To scroll through the list, press the up or down arrow key.
PageWriter Trim Cardiograph Instructions for Use 4-15
![Page 157: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/157.jpg)
PageWriter Trim II and III Orders and Archive Deleting Auto ECGs from the Archive
17 To select an Auto ECG to be saved to the cardiograph, press the Tab key or turn the Trim Knob and highlight the Select button. To select all of the Auto ECGs on the list, highlight the Select All button.
18 Press the space bar or the Trim Knob to select the Auto ECG(s).
19 Press the Tab key or turn the Trim Knob to highlight the Get Selected ECG(s) button.
20 Press the space bar or the Trim Knob to select the button and to save the selected Auto ECG(s) to the Remote Sites Archive on the cardiograph.
21 Press the Tab key or turn the Trim Knob to highlight the Close button.
22 Press the space bar or the Trim Knob to select the button. The Search window closes and the saved Auto ECGs appear on the Remote Sites archive list. To print a saved Auto ECG, see page 4-10.
Deleting Auto ECGs from the Archive Auto ECGs can be deleted from an Archive at any time. Auto ECGs may be deleted one at a time, or multiple Auto ECGs may be deleted. As Auto ECGs are deleted, the available space information for the selected Archive is updated, see Figure 4-2 on page 4-7.
CAUTION Deleted Auto ECGs cannot be retrieved.
To delete an Auto ECG from an archive:
1 Press the Tab key ( ) or turn the Trim Knob to highlight the drop-down list under Selected Archive (bottom of screen).
2 Press the space bar or the Trim Knob to open the drop-down list.
3 Press the up ( ) or down ( ) arrow key or turn the Trim Knob to highlight the Archive.
4 Press the space bar or the Trim Knob to select the Archive. The Auto ECGs contained in the selected Archive appear on the screen.
5 The selected Auto ECG appears highlighted (in dark blue or in dark gray) on the Report List. To select a different Auto ECG to be deleted, press the up or down arrow key.
6 To select multiple ECGs, press and hold down the Shift key ( ) and then press the up and down arrow key. To delete all of the Auto ECGs in the Archive, turn the Trim Knob to highlight the Select All button. Press the space bar or the Trim Knob to select the button.
7 When the ECG to be deleted is highlighted, press the Tab key or turn Trim Knob to highlight the Delete button.
8 Press the space bar or the Trim Knob to select the button. The Delete Selected ECGs window appears. The OK button is highlighted.
4-16 PageWriter Trim Cardiograph Instructions for Use
![Page 158: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/158.jpg)
Deleting Auto ECGs from the Archive PageWriter Trim II and III Orders and Archive
9 Press the space bar or the Trim Knob to select the button and to delete the selected Auto ECGs. To not delete the Auto ECGs, select the Cancel button. The Delete Selected ECGs progress bar window appears and the selected Auto ECGs are deleted from the Archive.
PageWriter Trim Cardiograph Instructions for Use 4-17
![Page 159: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/159.jpg)
5
ABCDEFGHI
Reading the Printed ECG Report
The following chapter describes the printed report formats available on the PageWriter Trim I, II and III cardiographs. Figure 3-1 describes the 3x4 1R report format that is available on all cardiograph models. For information on additional report formats, see page 5-18.Figure 5-1 A 12-Lead 3x4, 1R Report (page one)
A
B
CD
F
G
HI
J
K
(see page 3-11) LN M
E
OP
Q
Interpretive, Reason, and Severity Statements (see page 5-2) J Calibration Information (see page 5-11)Basic Measurements (see page 5-4) K Time Separator (see page 5-13)Patient ID Clinical Information (see page 5-5) L Pacing Detection Setting (see page 5-13)Patient ID Information (see page 5-6) M Algorithm Version (see page 5-16)Institution Information (see page 5-7) N Speed and Sensitivity Settings (see page 5-16)Configurable Clinical Information (see page 5-8) O Patient Name (see page 5-7)ECG Order Information (see page 5-9) P Patient ID Number (see page 5-7)Physician Information (see page 5-10) Q Device Identification Number (page 5-17)Report Information (see page 5-10)
5-1
![Page 160: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/160.jpg)
Reading the Printed ECG Report Interpretive, Reason, and Severity Statements
Additional Patient ID Clinical Information may appear on the top of a second page of the ECG report if more than two clinical fields (Rx, Dx, Sx, Hx) are entered with the Patient ID information.
Additional Configurable Clinical Information may also appear on the top of a second page of the ECG report if more than two fields are entered.Figure 5-2 A 12-Lead 3x4, 1R Report (page two)
Interpretive, Reason, and Severity Statements This area of the report contains the interpretive, reason, and severity statements generated by the Philips 12-Lead Algorithm. This feature is only available on the PageWriter Trim I and III. Figure 5-3 Interpretive, Reason, and Severity Statements on the ECG Report
Interpretive statements may include a reason statement that summarizes the criteria that generated the interpretive statement.
R
S
R Additional Patient ID Clinical Information (see page 5-5)S Additional Configurable Clinical Information (see page 5-8)
InterpretiveStatements
SeverityStatement
ReasonStatements
5-2 PageWriter Trim Cardiograph Instructions for Use
![Page 161: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/161.jpg)
Interpretive, Reason, and Severity Statements Reading the Printed ECG Report
NOTE The interpretive statements may include quality statements that describe a signal quality problem that occurred during recording, such as ARTIFACT IN LEAD(S) I, III, aVL.
For a complete listing (in alphabetical order and by diagnostic category) of all of the criteria included in the Philips 12-lead Algorithm, see Appendices B and C of the Philips 12-lead Algorithm Physician’s Guide on the User Documentation CD, or download the file from the Philips InCenter site (incenter.medical.philips.com). For information on using the Philips InCenter site, see page 1-4.
Severity Statement
Each interpretive statement included on the ECG report has an associated severity. Severities that are more abnormal override lesser severities. The severities of all selected interpretive statements are combined to determine the overall severity of the ECG. This severity code is printed on the front page of the ECG report.
Table 5-1 Overall ECG Severity with Code
Severity Code
No Severity NS
Normal ECG NO
Otherwise Normal ECG ON
Borderline ECG BO
Abnormal ECG AB
Defective ECG DE
PageWriter Trim Cardiograph Instructions for Use 5-3
![Page 162: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/162.jpg)
Reading the Printed ECG Report Basic Measurements
Basic MeasurementsThese measurements provide standard interval and duration measurements in milliseconds, and limb lead axis measurements in degrees. These are the values measured from the representative beat pattern in the ECG. This feature is only available on the PageWriter Trim II and III.Figure 5-4 Basic Measurements on the ECG Report
.
Table 5-1 Basic Measurements
Label Description Units
RATE Heart rate beats per minute
PR PR interval milliseconds
QRSD QRS duration milliseconds
QT QT interval milliseconds
QTc QT interval corrected for rate milliseconds
P Frontal P axis degrees
QRS Frontal QRS axis degrees
T Frontal T axis degrees
5-4 PageWriter Trim Cardiograph Instructions for Use
![Page 163: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/163.jpg)
Patient ID Clinical Information Reading the Printed ECG Report
Patient ID Clinical InformationThis area of page one or page two of the report contains clinical patient information that is entered with the Patient ID. This includes information about the patient’s Medications (Rx), Diagnoses (Dx), Symptoms (Sx), History (Hx), and a Diagnosis Related Group (DRG) code. This information is optional and configurable (see page 2-12). The example below is for informational purposes only. This feature is only available on the PageWriter Trim II and III.Figure 5-5 Patient ID Clinical Information on the ECG Report (page one)
If more than two Patient ID Clinical Information fields are entered, the third and subsequent fields appear at the top of a second page of the report. Figure 5-6 Patient ID Clinical Information on the ECG Report (page two)
PageWriter Trim Cardiograph Instructions for Use 5-5
![Page 164: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/164.jpg)
Reading the Printed ECG Report Patient ID Information
Patient ID InformationThis section contains patient identification information. This block of information is configurable (see page 2-8). The example below is for informational purposes only.Figure 5-7 Patient ID Information on the ECG Report
Table 5-1 Patient ID Information
Label Description
125-43-3247 Patient identification number
03/15/2003; 12:27:11 PM Date and time of ECG acquisition
Cannot be edited
Doe, John T. Patient name
Born 1936 Patient date of birth (may be configured to display patient age)
Male Patient gender
247 lbs, 70 in. Patient weight and height
BP: 133/90 Patient blood pressure (mm/Hg)
5-6 PageWriter Trim Cardiograph Instructions for Use
![Page 165: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/165.jpg)
Institution Information Reading the Printed ECG Report
Additional Patient ID InformationAdditional Patient ID information can be configured to appear at the bottom of the report (see page 2-23). This may be helpful if the patient name and ID is being cut off in the printed report format. This feature is only available on the PageWriter Trim II and III.Figure 5-8 Patient Name and ID information on the bottom of report
Institution InformationThis block of identification information is optional and is fully configurable (see page 2-42). The example below is for informational purposes only. This feature is only available on the PageWriter Trim II and III. Figure 5-9 Institution Information on the ECG Report
Table 5-2 Institution Information
Label Description
Community Hospital (21) Name and ID number of institution
Dept: ICU (13) Name and ID number of department
PageWriter Trim Cardiograph Instructions for Use 5-7
![Page 166: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/166.jpg)
Reading the Printed ECG Report Configurable Clinical Information
Configurable Clinical InformationThis information is configurable to fit specific clinical needs (see page 2-12). Up to six configurable drop-down fields are available. This feature is only available on the PageWriter Trim II and III.
The first four text fields appear on page one of the ECG report. The fifth and subsequent text fields appear on page two of the ECG report. The examples below are for informational purposes only.Figure 5-10 Configurable Clinical Information on the ECG Report (page one)
Figure 5-11 Configurable Clinical Information on the ECG Report (page two)
Room: 228 Room number of patient or room number where ECG was acquired
Oper: Williams Operator identification
Fac: West Campus (5) Name and ID number of facility or other unit within an institution
Table 5-2 Institution Information (continued)
Label Description
5-8 PageWriter Trim Cardiograph Instructions for Use
![Page 167: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/167.jpg)
ECG Order Information Reading the Printed ECG Report
ECG Order InformationThis area of the report is configurable to meet the requirements of an order management system (see page 2-14). This feature is only available on the PageWriter Trim II and III.Figure 5-12 ECG Order Information on the ECG Report
Table 5-3 ECG Order Information
Label Description
Order: 0-123 Institution-defined order number, part of order management system
Enc: E-123 Institution-defined encounter number, part of order management system
Reason: Annual Physical The reason for acquiring the ECG, may be part of an order management system
PageWriter Trim Cardiograph Instructions for Use 5-9
![Page 168: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/168.jpg)
Reading the Printed ECG Report Physician Information
Physician InformationThis information block is configurable (see page 2-14) and contains physician identification information, including the name of the ordering physician and UPIN (Universal Physician Identification Number). This feature is only available on the PageWriter Trim II and III.Figure 5-13 Physician Information on the ECG report
Report InformationInformation about the status of the ECG report is included in this section. The statement indicating that the ECG report has not been overread by a physician is configurable (see page 2-3). This feature is only available on the PageWriter Trim II and III.Figure 5-14 Report Information on the ECG Report
Table 5-4 Report Information
Label Description
Unconfirmed Diagnosis Indicates that the ECG report has not been overread by a qualified physician
COPY The ECG report is a printed copy of an original
STAT The ECG report is designated as STAT
5-10 PageWriter Trim Cardiograph Instructions for Use
![Page 169: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/169.jpg)
Calibration Information Reading the Printed ECG Report
Calibration InformationThe calibration pulse is the rectangular waveform shown in each line of ECG trace. It shows the hypothetical deflection of the trace in response to a 1 mV calibration pulse applied to the acquisition circuitry.Figure 5-15 Calibration Pulse on the ECG Report
The shape of the calibration pulse reflects the scaling of the trace.
If the calibration pulse is square the precordial leads and limb leads were recorded at the same scale.
If the calibration pulse is stepped the precordial leads were recorded at half the scale of the limb leads.
Non-standard lead gains The limb leads or precordial leads were recorded at a gain other than the standard 10mm/mV
See "Calibration Information" on page 5-11
Table 5-4 Report Information (continued)
Label Description
Table 5-5 Calibration Pulse Shapes
Calibration Pulse Shape Limb (mm/mV)
Precordial (mm/mV)
5 5
5 2.5
10 10
CalibrationPulse
PageWriter Trim Cardiograph Instructions for Use 5-11
![Page 170: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/170.jpg)
Reading the Printed ECG Report Calibration Information
NOTE For ECG recordings where the precordial leads or limb leads were recorded at a gain other than 10mm/mV, the statement Non-standard lead gains appears in the Report Information section on the printed report.
Figure 5-16 Calibration information on the ECG report
10 5
20 20
20 10
Table 5-5 Calibration Pulse Shapes (continued)
Calibration Pulse Shape Limb (mm/mV)
Precordial (mm/mV)
5-12 PageWriter Trim Cardiograph Instructions for Use
![Page 171: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/171.jpg)
Time Separator Reading the Printed ECG Report
Time SeparatorThe time separator marks indicate whether the ECG data is displayed simultaneously or time-sequentially. These settings are configured as part of a report or copy profile (see page 2-17). The data for each lead is always acquired simultaneously. Figure 5-17 Simultaneous time separator on ECG report
The double line indicates that the ECG data for each lead is displayed simultaneously. The starting point of each lead is the same time even though they may appear to start at different times on the printed report.Figure 5-18 Time sequential separator on ECG report
The single line indicates that the ECG data for each lead is displayed over a continuous period of time. For example, on a 3x4 grid all signals start at 0 in the first column, 2.5 seconds in the second column, 5.0 seconds in the third column, and 7.5 seconds in the fourth column.
Pacing Detection SettingsThis area of the report contains information about the pacing detection settings that were selected when the ECG report was printed.
Pacemaker pulses that are detected by the cardiograph are marked on the ECG report with small vertical tick marks. These marks enable the overreader to identify false pacemaker pulse detections, or if true pulses are not being detected.
SimultaneousTime Separator
Time SequentialSeparator
PageWriter Trim Cardiograph Instructions for Use 5-13
![Page 172: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/172.jpg)
Reading the Printed ECG Report Pacing Detection Settings
WARNING Pace pulse tick marks do not appear on any PageWriter Trim II and III report that include simultaneous (not time-sequential) acquisition settings. For information on simultaneous acquisition, see page 5-13. For information on report settings, see page 3-26.
Figure 5-19 Pacing Detection Setting on the ECG report
The table below describes the available Pacing Detection Settings with the pacing detection code that appears on the printed ECG report.
Table 5-6 Pacing Detection Settings
Setting Description ECG Report Code
Not known if paced This is the default setting and normally is used for both paced and non-paced patients.
Pacemaker pulse detection is on and is at normal sensitivity.
Occasional false pacemaker pulse detections may occur in ECGs with excessive noise.
False detections may result in an incorrect interpretive statement appearing on the report.
Small amplitude pacemaker pulses may not be detected using this setting.
P?
Non-paced Pacemaker pulse detection is off.
Use this setting if there are false pacemaker pulse detections from noise, or if incorrect interpretive statements or inappropriate paced ECG complexes appear on the report.
No code appears on the ECG report if the Non-paced setting is selected.
5-14 PageWriter Trim Cardiograph Instructions for Use
![Page 173: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/173.jpg)
Pacing Detection Settings Reading the Printed ECG Report
Paced Pacemaker pulse detection is on and is set at a higher sensitivity.
Use this setting if small amplitude pacemaker pulses are not being detected at the default (Not Known if Paced) setting.
False pacemaker pulse detections may occur if the ECG is noisy.
P
Paced (magnet) Use this setting if the ECG is acquired with an active pacemaker magnet or programmer in place.
Pacemaker pulse detection is on and is at a higher sensitivity.
Magnets or programmers often put the pacemaker in a fixed-rate, non-sensing mode.
On the PageWriter Trim I and III, the statement ECG ACQUIRED WITH MAGNET IN PLACE is printed on the ECG report. This statement notifies the overreader that a magnet or programmer was used and would explain the fixed rate behavior of the pacer.
PM
Table 5-6 Pacing Detection Settings (continued)
Setting Description ECG Report Code
PageWriter Trim Cardiograph Instructions for Use 5-15
![Page 174: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/174.jpg)
Reading the Printed ECG Report Algorithm Version Number
Algorithm Version NumberThe version number of the Philips 12-Lead Algorithm is printed at the bottom of the ECG Report. The algorithm versions PH080A and PH090A are available on the PageWriter Trim II and III cardiographs, see page 2-3 for more information. Algorithm version PH090A is available on the PageWriter Trim I cardiograph.Figure 5-20 Algorithm Version Number on the ECG Report
Speed and Sensitivity SettingsThis area contains information about the speed and sensitivity settings that were used for the ECG recording.Figure 5-21 Speed and Sensitivity Settings on the ECG Report
Table 5-7 Algorithm Version Number
Label Description
PH080A or PH090A PH refers to Philips
08 or 09 refers to the version of the measurement program
0A refers to the criteria version installed on the cardiograph
Table 5-8 Speed and Sensitivity Settings
Label Description
Speed The speed at which the ECG was printed
Available settings:– 25mm/sec – 50 mm/sec
5-16 PageWriter Trim Cardiograph Instructions for Use
![Page 175: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/175.jpg)
Device Identification Number Reading the Printed ECG Report
NOTE For ECG recordings where the precordial leads or limb leads were recorded at a gain other than 10mm/mV, the statement Non-standard lead gains appears in the Report Information section on the printed report.
Device Identification Number This number is entered in Configuration (see page 2-42). This number is used to identify the individual cardiograph that was used to acquire the ECG. This feature is only available on the PageWriter Trim II and III.Figure 5-22 Device ID on the ECG Report
Limb The limb lead sensitivity setting
Available settings: – 5, 10, or 20 mm/mV
Chest Precordial lead sensitivity setting
Available settings:– 2.5, 5, 10, or 20 mm/mV
Table 5-8 Speed and Sensitivity Settings (continued)
Label Description
PageWriter Trim Cardiograph Instructions for Use 5-17
![Page 176: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/176.jpg)
Reading the Printed ECG Report 12-Lead ECG Report Examples
12-Lead ECG Report ExamplesThe following section includes examples of other 12-Lead report formats available on the PageWriter Trim II and III cardiographs.
3x4, 3R report with Standard Leads
3x4, 1R report with Cabrera Leads
6x2 report (5-second waveform segments) with Cabrera Leads
12x1 report with Cabrera Leads. The 12x1 report shows 10 seconds of continuous waveform data for 12 leads and includes a second page with interpretive, reason, and severity statements (if configured).
Panoramic (Pan-12) report with Cabrera Leads. The Pan-12 report shows a one-second representative complex for each Cabrera Lead with three pre-selected rhythm strips at the bottom (aVF, V2, V5).
NOTE The available PageWriter Trim I report formats are: 3x4 1R with Standard lead sequence, 6x2 with Cabrera lead sequence, and 3 and 6 lead Rhythm reports.
5-18 PageWriter Trim Cardiograph Instructions for Use
![Page 177: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/177.jpg)
12-Lead ECG Report Examples Reading the Printed ECG Report
Figure 5-23 3x4, 3R Report with Standard Leads
PageWriter Trim Cardiograph Instructions for Use 5-19
![Page 178: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/178.jpg)
Reading the Printed ECG Report 12-Lead ECG Report Examples
Figure 5-24 3x4, 1R Report with Cabrera Leads and Simultaneous Acquisition
5-20 PageWriter Trim Cardiograph Instructions for Use
![Page 179: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/179.jpg)
12-Lead ECG Report Examples Reading the Printed ECG Report
Figure 5-25 6x2 Report with Cabrera Leads
PageWriter Trim Cardiograph Instructions for Use 5-21
![Page 180: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/180.jpg)
Reading the Printed ECG Report 12-Lead ECG Report Examples
Figure 5-26 12x1 Report with Cabrera Leads (page one)
5-22 PageWriter Trim Cardiograph Instructions for Use
![Page 181: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/181.jpg)
12-Lead ECG Report Examples Reading the Printed ECG Report
Figure 5-27 12x1 Report with Cabrera Leads (page two)
PageWriter Trim Cardiograph Instructions for Use 5-23
![Page 182: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/182.jpg)
Reading the Printed ECG Report 12-Lead ECG Report Examples
Figure 5-28 Panoramic (Pan-12) Report
NOTE Leads are displayed in Cabrera sequence on the Panoramic (Pan-12) Report regardless of the selected lead standard on the cardiograph.
5-24 PageWriter Trim Cardiograph Instructions for Use
![Page 183: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/183.jpg)
Extended Measurements Report Reading the Printed ECG Report
Extended Measurements ReportPageWriter Trim III only
The Extended Measurements report summarizes the output of the Philips 12-Lead Algorithm. The report includes the morphology characteristics for the individual leads, and the rhythm characteristics for the rhythm groups. The algorithm uses this measurement information to generate interpretive statements. The Extended Measurements report is especially useful if you want to examine the measurements used to generate an interpretation.
For more information on the Extended Measurements Report, see Chapter 5 of the Philips 12-Lead Algorithm Physician’s Guide on the User Documentation CD, or download the file from the Philips InCenter site (incenter.medical.philips.com). For information on using the Philips InCenter site, see page 1-4.
Rhythm ReportRhythm reports show up to 12 leads of continuous waveform data. The amount of report information that is included on the report is dependent upon the number of leads selected for recording. Information on the report may include:
Patient ID information
Date and time of recording
Settings information (scale and sensitivity, filter settings)
Rhythm reports are not analyzed, so they do not provide measurement information or interpretive statements, and they are not saved to the Archive. The calibration pulse appears at the beginning of the ECG trace.
PageWriter Trim Cardiograph Instructions for Use 5-25
![Page 184: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/184.jpg)
Reading the Printed ECG Report Rhythm Report
Figure 5-29 A Rhythm Report with 6 Leads
5-26 PageWriter Trim Cardiograph Instructions for Use
![Page 185: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/185.jpg)
Rhythm Report Reading the Printed ECG Report
Figure 5-30 A Rhythm Report with 12 Leads
PageWriter Trim Cardiograph Instructions for Use 5-27
![Page 186: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/186.jpg)
Reading the Printed ECG Report Disclose Report
Disclose ReportPageWriter Trim II and III only
The Disclose report displays up to one minute of continuous ECG waveform data for one selected lead. Disclose reports are not analyzed, so they do not provide measurement information or interpretive statements, and they are not saved to the Archive. Each 10-second waveform segment on the report is labeled next to the lead name.Figure 5-31 1 Minute Disclose Report
5-28 PageWriter Trim Cardiograph Instructions for Use
![Page 187: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/187.jpg)
6
1Troubleshooting
IntroductionCommon troubleshooting topics are discussed in this chapter. If additional assistance is required, contact the nearest Philips Response Center (see page 7-24).
Troubleshooting Topics
The following table lists all of the Troubleshooting topics included in this chapter.
Table 6-1 Troubleshooting Topics
Topic Page Number
Archive see page 6-2
Barcode Reader see page 6-6
Battery and AC Power see page 6-6
LAN and Modem card see page 6-8
Leads Off see page 6-9
Magnetic Card Reader see page 6-10
Printer see page 6-10
Signal Quality (bad electrode connection, interference or noise in ECG signal)
see page 6-14
System Freeze see page 6-16
6-1
![Page 188: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/188.jpg)
Troubleshooting Archive
ArchiveThe following table includes common error messages that may appear when using the Archive and common problems that may occur when using the Archive to transmit ECGs to a TraceMasterVue ECG Management System.
Table 6-2 Archive Troubleshooting
Error Message or Problem
Possible Cause Solution
Archive Error: Command Timed Out
The TraceMasterVue ECG Management system is busy at the receiving end.
Wait and try again.
Archive Error: Command Timed Out
The analog phone line is disconnected or was interrupted while an ECG is being transferred to a TraceMasterVue Remote Site.
Check that the phone connector is properly inserted into the modem card and the modem has a dial tone.
Cannot Access Selected Archive
The Selected Archive is a PC card and there is no PC card inserted into the PC card slot (rear of cardiograph) or the PC card is not fully inserted into the PC card slot.
Check that the PC card is correctly orientated in the PC card slot and that the PC card is fully inserted into the slot.
Remote Connection Failed
The connection between the TraceMasterVue server and the PageWriter Trim cardiograph is not established, or is not configured properly.
Check the cardiograph Network settings, and the Remote Site settings in Configuration (see page 2-33).
Check with your System Administrator regarding TraceMasterVue network permission and access.
Check that the LAN card or modem card is correctly orientated in the PC card slot and that the card is fully inserted.
Cannot store additional ECG
The selected Archive is full. Delete unwanted ECGs from the Archive (see page 4-16).
6-2 PageWriter Trim Cardiograph Instructions for Use
![Page 189: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/189.jpg)
Archive Troubleshooting
Archive Error: XML Error
ECG files have been corrupted during the transfer or retrieval from a TraceMasterVue server.
XML files from an unknown device are being transferred to the cardiograph.
Try transferring or retrieving the ECG again.
If the error message is received a second or subsequent time, contact the nearest Philips Response Center for further assistance (see page 7-24).
The PageWriter Trim cardiograph only supports the importing of XML files from the PageWriterTouch and other PageWriter Trim cardiographs.
Archive Error: Invalid Database
There are unspecified errors on the PC card inserted into the PC card slot on the rear of the cardiograph, or on the internal cardiograph CompactFlash card.
There is an unspecified error with the USB memory stick that is inserted into the USB connector on the rear of the cardiograph.
Try accessing the Archive again.
If the error message is received a second or subsequent time, contact the nearest Philips Response Center for further assistance (see page 7-24).
Archive Error: Requested Function Failed
An unsupported Auto ECG format is being transferred to a TraceMasterVue ECG Management System.
Pan-12 and 12x1 reports may not be transferred to a TraceMasterVue ECG Management System.
Table 6-2 Archive Troubleshooting (continued)
Error Message or Problem
Possible Cause Solution
PageWriter Trim Cardiograph Instructions for Use 6-3
![Page 190: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/190.jpg)
Troubleshooting Archive
When multiple ECGs are being transferred from the cardiograph to a TraceMasterVue Remote Site, not all ECGs transfer and are not deleted from the Archive.
The ECG transfer was interrupted for an unknown reason.
Transfer the ECGs again.
If the ECGs do not transfer after a second or subsequent time, contact the nearest Philips Response Center for assistance (see page 7-24).
After selecting the Archive button on the Command Toolbar, it takes longer than 40 seconds for the Archive Report List to display on the screen.
The Main Archive (internal cardiograph archive) contains more than 150 ECGs and is full.
Transmit and delete ECGs from the Main Archive (see page 4-9).
An ECG cannot be transferred to a PC card or to a USB memory stick when there are less than 100 ECGs on the PC card or on the USB memory stick.
There are other non-ECG files on the PC card or on the USB memory stick that are taking up space.
Delete files from the PC card or from the USB memory stick and attempt to transfer the ECG(s) again.
Table 6-2 Archive Troubleshooting (continued)
Error Message or Problem
Possible Cause Solution
6-4 PageWriter Trim Cardiograph Instructions for Use
![Page 191: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/191.jpg)
Archive Troubleshooting
CAUTION Do not pull the PC card out of the PC card slot, or pull the USB memory stick out of the USB connector while the cardiograph is accessing ECG files from either type of removable media.
The ECG retrieved from a TraceMasterVue ECG Management System does not print as expected or appear as expected on the Preview screen.
The ECG was not originally generated on a PageWriter Trim or PageWriterTouch cardiograph.
Retrieving and printing ECGs that were not generated on a PageWriter Trim or a PageWriterTouch cardiograph may result in the following:
The algorithm version number appears as HPxx on the TraceMasterVue ECG Management System, but will appear as PH on the PageWriter Trim (see page 5-16).
Pacer tick marks do not appear on the ECG report printed on the PageWriter Trim.
If the ECG was originally generated using the Frank lead system, the PageWriter Trim will print the report with three flat Rhythm strips with no lead information.
Custom lead names will not appear on a report printed on a PageWriter Trim.
Table 6-2 Archive Troubleshooting (continued)
Error Message or Problem
Possible Cause Solution
PageWriter Trim Cardiograph Instructions for Use 6-5
![Page 192: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/192.jpg)
Troubleshooting Barcode Reader
Barcode ReaderThe following table describes a potential problem with the barcode reader.
Battery and AC Power The following table describes common problems with the battery and AC power.
Table 6-3 Barcode Reader Troubleshooting
Problem Possible Cause Solution
The barcode reader does not accurately read a scanned barcode.
The barcode reader has been unplugged or plugged into the cardiograph when the cardiograph is in use.
Shut down all power to the cardiograph. Press and hold the On/Standby button for three seconds and then release. Securely attach the barcode reader to the barcode reader port ( ) on the rear of the cardiograph. Press the On/Standby button.
Table 6-4 Battery and AC Power Troubleshooting
Problem Possible Cause Solution
The AC power indicator light on the front of the cardiograph does not illuminate when the cardiograph is plugged into AC power.
The AC fuse is not functional. The AC fuse needs to be replaced (see page 7-9).
6-6 PageWriter Trim Cardiograph Instructions for Use
![Page 193: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/193.jpg)
Battery and AC Power Troubleshooting
No battery detected. The battery is completely depleted of power and requires a full recharge.
The battery is damaged.
The battery has been removed from the cardiograph.
Check that the battery is properly inserted (see page 1-14).
Recharge the battery. Plug the cardiograph into AC power and press the On/Standby button. Charge the battery until the Battery Power Indicator on the Status Bar displays that the battery is fully charged (see page 1-33).
Replace the battery (see page 7-8). Only use the PageWriter Trim replacement battery with Philips part number 989803130151.
Table 6-4 Battery and AC Power Troubleshooting (continued)
Problem Possible Cause Solution
PageWriter Trim Cardiograph Instructions for Use 6-7
![Page 194: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/194.jpg)
Troubleshooting LAN and Modem Card
LAN and Modem CardThe following table lists some common problems with the Ethernet LAN or modem PCMCIA card.
Table 6-5 LAN and Modem Card Troubleshooting
Problem Possible Cause Solution
The Transfer, Query, Search or Fax functions do not operate.
The LAN cable or phone cable is not connected to the card.
The configured settings for the TraceMasterVue Remote Site are incorrect.
Check that the LAN cable or phone cable are correctly and securely attached to the card.
Only use the shielded LAN cable supplied with the PageWriter Trim cardiograph with Philips part number 989803138021. Do not use any other LAN cable with the cardiograph.
Check the configured settings for the Remote Site (see page 2-33).
The modem card does not respond.
The modem card is not fully inserted into the PC card slot, or was removed and replaced while the cardiograph was in operation.
Ensure that the modem card is fully inserted into the PC card slot on the rear of the cardiograph.
Reset the cardiograph (see page 6-17) and attempt to use the modem card again.
If the modem card fails to respond a second or subsequent time, contact the nearest Philips Response Center for assistance (see page 7-24).
6-8 PageWriter Trim Cardiograph Instructions for Use
![Page 195: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/195.jpg)
Leads Off Troubleshooting
Leads OffThe following table lists some common problems with leads off.
Table 6-6 Leads Off Troubleshooting
Lead(s) shown disconnected
Possible Cause Solution
RL or N The PIM (Patient Interface Module) patient data cable is not securely attached to the PIM connector port on the rear of the cardiograph.
The RL or N electrode or lead wire are lose or disconnected.
More than two of the following leads: LA or L, LL or F, or RA or R are loose or disconnected.
Check that the patient data cable is securely attached to the PIM connector port ( ) on the rear of the cardiograph.
Check that the RL or N electrodes or lead wires are securely attached.
Check that the electrodes and lead wires are correctly positioned on the patient (see page 3-3).
Ensure that there are at least two limb lead wires securely connected.
LL or F LL or F (left leg) electrode and lead wire are loose or disconnected.
Check LL or F lead wire and electrode are securely attached.
LA or L LA or L (left arm) electrode and lead wire are loose or disconnected.
Check LA or L electrode and lead wire are securely attached.
RA or R RA or R (right arm) electrode and lead wire are loose or disconnected.
Check RA or R electrode and lead wire are securely attached.
V1-V6 or C1-C6 V1-V6 (C1-C6) precordial electrodes and lead wires are loose or disconnected.
Check the V1-V6 (C1-C6) electrodes and lead wires are securely attached.
PageWriter Trim Cardiograph Instructions for Use 6-9
![Page 196: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/196.jpg)
Troubleshooting Magnetic Card Reader
Magnetic Card ReaderThe following table describes a potential problem with the magnetic card reader.
Printer The following table contains a list of common error messages and other problems that may occur when using the cardiograph printer.
Table 6-7 Magnetic Card Reader Troubleshooting
Problem Possible Cause Solution
The magnetic card reader does not correctly read the magnetic card data.
The magnetic card reader has been connected or disconnected from the cardiograph while the cardiograph is in use.
Shut down all power to the cardiograph. Press and hold the On/Standby button for three seconds and then release. Securely attach the magnetic card reader to the magnetic card reader port ( ) on the rear of the cardiograph. Press the On/Standby button.
Table 6-8 Printer Troubleshooting
Error Message or Problem
Possible Cause Solution
PageWriter Trim II and III:Printer Error: Door is Open
PageWriter Trim I:0203
The paper drawer is open.
There is an unknown problem with the printer.
Open and close the printer drawer and ensure that it is securely closed.
If the problem persists, contact the nearest Philips Response Center for further assistance (see page 7-24).
PageWriter Trim II and III:Printer Error: Out of Paper
PageWriter Trim I:0204
No printer paper in the paper drawer.
Replace the printer paper (see page 7-4).
6-10 PageWriter Trim Cardiograph Instructions for Use
![Page 197: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/197.jpg)
Printer Troubleshooting
PageWriter Trim II and III:Printer Error: Paper Jam
PageWriter Trim I:0204
There is a paper jam. Pull out the paper drawer and fix the paper jam.
PageWriter Trim II and III:Printer Error: Printer Busy
PageWriter Trim I:
0202
The cardiograph is configured for a particular paper size (A or A4), and the paper drawer is loaded with a different size paper.
The battery charge level is at low power.
The paper drawer was opened while the cardiograph was printing a report.
Check that the paper size setting in configuration is correct (see page 2-23).
Plug the cardiograph into AC power and fully charge the battery, or replace the battery with a new fully charged battery (see page 7-8).
Reset the cardiograph (see page 6-17).
Table 6-8 Printer Troubleshooting (continued)
Error Message or Problem
Possible Cause Solution
PageWriter Trim Cardiograph Instructions for Use 6-11
![Page 198: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/198.jpg)
Troubleshooting Printer
PageWriter Trim II and III:Printer Error: USB
PageWriter Trim I:
0201
The battery power level is too low to print a report.
The printer is not responding.
Plug the cardiograph into AC power and fully charge the battery, or replace the battery with a new fully charged battery (see page 7-8).
Open the paper drawer and securely close it.
If all other methods fail to resolve the error message, press and hold the On/Standby button for three seconds then release it to shut down the cardiograph. Push the On/Standby button again to restart the cardiograph. The cardiograph will fully reboot.
For further assistance, contact the nearest Philips Response Center (see page 7-24).
PageWriter Trim II and III:Printer Error: Unknown Error
PageWriter Trim I:
0207
Unknown cause for problem. Open and securely close the paper drawer and then reset the cardiograph (see page 6-17).
For further assistance, contact the nearest Philips Response Center (see page 7-24).
Table 6-8 Printer Troubleshooting (continued)
Error Message or Problem
Possible Cause Solution
6-12 PageWriter Trim Cardiograph Instructions for Use
![Page 199: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/199.jpg)
Printer Troubleshooting
The printer makes a click noise and will not respond.
The printer is unable to function due to an unknown cause.
Follow the cardiograph reset procedure (see page 6-17).
If the problem persists, contact the nearest Philips Response Center for further assistance (see page 7-24).
The cardiograph prints out a blank ECG report and will not stop printing.
The cardiograph is configured for a particular paper size (A or A4), and the paper drawer is loaded with a different size paper.
Press the Stop button on the cardiograph to stop the printer.
Press the On/Standby button for three seconds then release it to shut down the cardiograph. Press the On/Standby button again to restart the cardiograph.
Configure the cardiograph for the correct paper size (see page 2-23).
The printer paper does not advance to the correct position at the top of the next sheet. The perforated edge does not appear at the end of the report.
The cardiograph is configured for a particular paper size (A or A4), and the paper drawer is loaded with a different size paper.
The printer paper is being torn off incorrectly.
Configure the correct paper size in Configuration (see page 2-23).
Review the correct procedure to tear off the printer paper (see page 7-4).
The printer stops printing unexpectedly.
The battery is depleted of power or is defective.
Plug the cardiograph into AC power. If the cardiograph prints reports normally, fully charge the battery or replace it.
If the problem persists, contact the nearest Philips Response Center (see page 7-24).
Table 6-8 Printer Troubleshooting (continued)
Error Message or Problem
Possible Cause Solution
PageWriter Trim Cardiograph Instructions for Use 6-13
![Page 200: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/200.jpg)
Troubleshooting Signal Quality
Signal QualityThe following section describes common signal quality problems with suggested solutions.Figure 6-1 AC interference
Blank pages appear at the end of the ECG report.
The cardiograph is configured for a particular paper size (A or A4), and the paper drawer is loaded with a different size paper.
Configure the correct paper size in Configuration (see page 2-23).
Table 6-8 Printer Troubleshooting (continued)
Error Message or Problem
Possible Cause Solution
Table 6-9 AC Interference Troubleshooting
Possible Cause Solution
An improperly gelled electrode (dried gel)
Electrical interference from another device (IV pump, microwave oven, cellular phone, wireless device)
An electrical device near the cardiograph that is improperly grounded
Check that the electrodes are firmly attached.
Check for devices that could be causing electrical interference. Unplug the devices or switch to battery power.
Lay the lead wires alongside the limbs and away from any electrical devices.
Turn on the AC filter (see page 3-11).
6-14 PageWriter Trim Cardiograph Instructions for Use
![Page 201: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/201.jpg)
Signal Quality Troubleshooting
Figure 6-2 Wandering Baseline
Figure 6-3 Somatic Tremors
Table 6-10 Wandering Baseline Troubleshooting
Possible Cause Solution
Inadequate patient preparation, or a sweaty patient
Moderate patient movement, tense patient
Very poor electrode contact, dry electrodes
Patient respiratory interference
Reassure the patient and make sure that the patient is comfortable. If the patient has tremors, attach the limb electrodes higher on the patient (closer to torso).
Ensure that the lead wires are not pulling on the electrodes.
Check that the electrodes are firmly attached or reapply new electrodes if the gel is dry.
Turn on the Baseline Wander filter (see page 3-11).
PageWriter Trim Cardiograph Instructions for Use 6-15
![Page 202: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/202.jpg)
Troubleshooting System Freeze
Figure 6-4 Loose Electrode
System FreezeIf the cardiograph freezes on any screen and cannot be used, follow the procedure below to reset the cardiograph. For further assistance with system freeze issues, contact the nearest Philips Response Center (see page 7-24).
Table 6-11 Somatic Tremors Troubleshooting
Possible Cause Solution
The patient is cold and shivering
Patient has tremors
Place a blanket on the patient to warm the patient
Assist with limiting patient movement
Table 6-12 Loose Electrode Troubleshooting
Possible Cause Solution
An electrode is loose or is not adhering to the skin
An electrode has fallen off
A lead wire is disconnected
Check all electrodes
Replace dry electrodes
Check all lead wires
6-16 PageWriter Trim Cardiograph Instructions for Use
![Page 203: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/203.jpg)
System Freeze Troubleshooting
Resetting the Cardiograph
Follow the procedure below to reset the cardiograph.
To reset the cardiograph:
1 Press and hold down the On/Standby button for three seconds, and then release it. If the cardiograph does not shut down, follow the next step in this procedure.
2 Press and hold the On/Standby button for five seconds, then release it. Press the On/Standby button again. If the cardiograph does not shut down, perform the following steps in this procedure.
3 Using a paper clip or other item with a small tip, gently press the Reset button on the rear of the cardiograph.
Figure 6-5 Pressing the Reset button on the PageWriter Trim I
Table 6-13 System Freeze Troubleshooting
Problem Possible Cause Solution
The cardiograph cannot perform any function. The cardiograph does not respond when the Trim Knob is turned or pressed, or when a key on the keyboard is pressed.
The cardiograph software is frozen.
Follow the cardiograph reset procedure (see page 6-17).
If the cardiograph automatically resets.
The cardiograph resolved a problem by resetting.
Continue with normal cardiograph operation after the reset is complete. If the cardiograph continues to reset automatically, contact the nearest Philips Response Center for assistance (see page 7-24).
PageWriter Trim Cardiograph Instructions for Use 6-17
![Page 204: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/204.jpg)
Troubleshooting System Freeze
Figure 6-6 Pressing the Reset button on the PageWriter Trim II and III
The cardiograph display shuts off and the cardiograph restarts.
4 If the cardiograph does not restart after pressing the Reset button, disconnect the AC power cord from the cardiograph. Ensure that the AC power indicator light on the front of the cardiograph is not lit. Open the battery door and remove the battery from the cardiograph (see page 7-8). Reinsert the battery and connect the AC power cord to the AC power connector on the rear of the cardiograph. Press the On/Standby button. After the cardiograph is reset, a series of screens appear. At the end of the restart sequence, the R/T ECG screen appears and the cardiograph can be returned to normal use.
6-18 PageWriter Trim Cardiograph Instructions for Use
![Page 205: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/205.jpg)
7
1Cardiograph Care and Maintenance
The following chapter contains information on basic cardiograph care and periodic maintenance. If further technical assistance is required, contact the nearest Philips Response Center (see page 7-24).
Cardiograph CleaningTo clean the cardiograph:
1 Unplug the AC power cord.
2 Wipe the external surfaces of the cardiograph with a soft cloth dampened in any of the approved cleaning solutions listed below.
CAUTION When cleaning, avoid the lead wire connectors and the connectors on the rear panel.
Approved Cleaning SolutionsMild soap and water
Isopropyl alcohol
CAUTION Do not spill liquids on the surface of the cardiograph.
Do not use any of the following to clean the cardiograph:
Acetone
Iodine-based cleaners
Phenol-based cleaners
Ethylene oxide sterilization
Chlorine bleach
Ammonia-based cleaners
The cardiograph or PIM should not be autoclaved, ultrasonically cleaned, or immersed.
7-1
![Page 206: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/206.jpg)
Cardiograph Care and Maintenance PIM, Patient Data Cable and Lead Wire Cleaning
PIM, Patient Data Cable and Lead Wire CleaningTo clean the PIM, patient data cable and lead wires:
1 Dampen a soft cloth with one of the disinfectants or cleaning agents listed below. Clean the patient data cable and lead wires with any of the following:
Cidex Ortho Phthaladehyde
Cetylcide
Vesphene 2 Aqueous Phenolic Germicidal Agent
CAUTION Do not:
Use isopropyl alcohol
Autoclave the PIM, patient data cable or lead wires or use ultrasonic cleaners
Immerse
Use abrasive materials
Wet the connectors
2 Wring excess moisture from the cloth before cleaning.
Reusable Electrode CleaningTo clean reusable electrodes:
1 Dampen a soft cloth with one of the disinfectants or cleaning agents listed below.
Cidex Ortho Phthaladehyde
Cetylcide
Vesphene 2 Aqueous Phenolic Germicidal Agent
CAUTION Do not:
Use isopropyl alcohol
Autoclave the reusable electrodes or use ultrasonic cleaners
Use abrasive materials
2 Wring excess moisture from the cloth before cleaning.
7-2 PageWriter Trim Cardiograph Instructions for Use
![Page 207: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/207.jpg)
Changing the Date and Time on the PageWriter Trim I Cardiograph Care and Maintenance
Changing the Date and Time on the PageWriter Trim ITo change the date and time:
1 Turn the Trim Knob until the date on the LCD display is highlighted.
2 Push the Trim Knob. A screen appears showing the current date and time settings.
3 Turn the Trim Knob until the field to be changed is highlighted.
4 Push the Trim Knob to select the field.
5 Turn the Trim Knob to scroll through the options for that field.
6 Push the Trim Knob to select a setting.
7 Repeat the procedure to set the current Month, Day, Year, Hour, Minute, and Second.
8 When all settings are complete, turn the Trim Knob to highlight the arrow icon .
9 Push the Trim Knob to save the settings and to exit the screen.
Changing the Date and Time on the PageWriter Trim II and III
The following procedure changes the current displayed date and time. For information on changing the format of the displayed date and time (12 hour or 24 hour clock, or other date settings), see page 2-41.
To change the date and time:
1 Press the Tab key ( ) or turn the Trim Knob to highlight the displayed date and time on the Command Toolbar.
2 Press the space bar or the Trim Knob to select it. The Date and Time Settings window appears.
3 The month drop-down list is highlighted. Press the space bar or the Trim Knob to display the drop-down list.
4 Press the up ( ) or down ( ) arrow key or turn the Trim Knob to highlight the current month. Press the space bar or the Trim Knob to select it.
5 Repeat the procedure to select the current year, date and time.
6 When done, press the Enter key ( ) to save the new date and time settings. The new date and time appears on the Command Toolbar.
PageWriter Trim Cardiograph Instructions for Use 7-3
![Page 208: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/208.jpg)
Cardiograph Care and Maintenance Printer Paper
Printer PaperReplace the printer paper when a red stripe appears on the printed ECG report. Only use Philips Medical Systems replacement printer paper. For part number and ordering information, see page 7-21.
Tips for changing printer paperAlways load less than 100 sheets of printer paper into the paper tray
Ensure that the entire first page of the new paper roll is fully draped over the roller before closing the printer door
PageWriter Trim II and III:
Ensure that the paper size configured for the cardiograph is the same size paper being loaded into the paper drawer (see page 2-23)
To load paper into the printer:
1 Open the paper drawer on the front of the cardiograph and lift up the bar.
2 Insert a new pack of printer paper as shown. Ensure that no more than 100 sheets are being inserted into the paper tray.
7-4 PageWriter Trim Cardiograph Instructions for Use
![Page 209: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/209.jpg)
Printer Paper Cardiograph Care and Maintenance
3 Ensure that the paper sensor hole (A) is positioned as shown.
4 Drape the entire first sheet over the roller. Ensure that the perforated edge of the paper aligns with the edge of the paper drawer. Lower the bar onto the paper and close the drawer.
5 Tear off the first sheet as shown.
PageWriter Trim Cardiograph Instructions for Use 7-5
![Page 210: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/210.jpg)
Cardiograph Care and Maintenance Battery Maintenance and Care
Battery Maintenance and CareThe cardiograph uses one sealed lead-acid battery that supplies power to the cardiograph during mobile use, and provides a power supply to the cardiograph printer at all times. The battery must be inserted into the cardiograph at all times. The cardiograph cannot print a report without the battery, even when it is plugged into AC power.
With the battery fully charged, the cardiograph can print approximately 30 Auto ECGs or provide 30 minutes of continuous Rhythm printing.
Review the following important information about the care and use of the cardiograph battery.
For optimal battery performance:
Only use Philips Medical Systems PageWriter Trim replacement battery with the cardiograph (Philips Part Number 989803130151).
Plug the cardiograph into AC power whenever possible to maximize battery life and performance. Regularly and consistently charging the battery will prolong battery life.
CAUTION Repeated undercharging of the battery will damage the battery and will reduce battery life.
If the battery has been fully charged and requires recharging after only a few ECGs, consider replacement.
Charging the battery at temperatures above 45 oC (113o F) can damage the battery and can reduce overall battery life.
Check the battery power indicator on the Status Bar to ensure that the battery is fully charged, see "PageWriter Trim II and III Status Bar" on page 1-33.
For the PageWriter Trim II and III, configure and turn on the Battery Power Saving Modes (Standby, Shutdown) feature in Configuration, see page 2-23.
For the PageWriter Trim II and III, put the cardiograph into Standby mode when not in use. Push the On/Standby button to put the cardiograph into Standby. For the PageWriter Trim I, push the On/Off button to turn off the cardiograph when not in use.
Always charge the battery when the cardiograph is not in use. Plug the cardiograph into AC power. Ensure that green AC power indicator light is on. The battery will charge while the cardiograph is in use, but will charge at a slower rate.
The use of cardiograph accessories (barcode reader, magnetic card reader, SmartCard Reader, PC card, modem and LAN card) will deplete battery power at a faster rate. The battery will require more frequent charging if these accessories are used with the cardiograph.
Operate the cardiograph, charge the battery, and store the battery at a temperature of 40 oC (104o F) or lower. Exposure to higher temperatures may reduce battery life, damage the battery, and degrade overall cardiograph performance.
For optimal battery performance store the battery at a cooler temperature, but not below freezing (0 oC/32oF).
7-6 PageWriter Trim Cardiograph Instructions for Use
![Page 211: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/211.jpg)
Charging the Battery Cardiograph Care and Maintenance
If the cardiograph will be stored for more than thirty days without use, unplug the cardiograph from AC power and remove the battery. See “Battery Storage” on page 7-7 for more information.
A fully charged battery stored outside the cardiograph will need to be recharged every six months. If the battery is not charged every six months it will be damaged. See “Battery Storage” on page 7-7 for more information.
Charging the BatteryPlug the cardiograph into AC power whenever possible to charge the battery. The battery will charge when the cardiograph is in use and is plugged into AC power, but will charge at a slower rate.
If the battery is fully depleted, a charge time of at least 16 hours is necessary to fully recharge the battery. The battery will operate for approximately 8 hours before it requires a full recharge.
CAUTION Repeated undercharging of the battery will degrade battery performance and reduce overall battery life.
For the PageWriter Trim I, check the Battery Level Indicator on the LCD display ( ) to confirm that the battery is fully charged, see "LCD Display" on page 1-30. For the PageWriter Trim II and III, check the Battery Level Indicator on the Status Bar ( ) to confirm that the battery is fully charged, see "PageWriter Trim II and III Status Bar" on page 1-33.
Battery Storage Remove the battery from the cardiograph if it will be stored for more than 30 days without use. While in storage, the battery will require a full recharge every 6 months. Charge the battery for at least 16 hours. This will ensure that the battery does not completely discharge while in storage. The battery life will be prolonged when stored in cooler temperatures, but will be damaged if stored below freezing (0 oC/32oF). Store the battery at a temperature of 40 oC (104o F) or lower.
To store the battery:
1 Charge the battery for 16 hours before removing it from the cardiograph. Ensure that the AC power cord is connected to the cardiograph and is plugged into a grounded AC power outlet. Check that the green AC power indicator light on the front of the cardiograph is lit.
2 Remove the battery from the cardiograph and store in a cool, dry location. For information on removing the battery, see “Replacing the Battery” on page 7-8.
3 Recharge the battery for 16 hours for every 6 months that the battery is in storage.
PageWriter Trim Cardiograph Instructions for Use 7-7
![Page 212: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/212.jpg)
Cardiograph Care and Maintenance Replacing the Battery
Replacing the Battery
WARNING Properly dispose of or recycle the depleted battery according to local regulations. Do not disassemble, puncture, or incinerate the disposed battery.
How often battery needs to be replaced depends on how well the battery is maintained and how much it is used. If the battery is fully charged but loses significant power after only a few ECGs, consider replacement. Figure 7-1 Replacing the Battery
To replace the battery:
1 Unplug the cardiograph from AC power and ensure that the green AC power indicator light on the front of the cardiograph is not lit.
2 Open the battery door on the rear of the cardiograph. Push the recessed tab in and pull it down to open the battery door.
7-8 PageWriter Trim Cardiograph Instructions for Use
![Page 213: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/213.jpg)
Replacing the AC Fuse Cardiograph Care and Maintenance
3 Remove the battery.
4 Insert the replacement battery into the compartment with the connector facing down and the pull tab facing out.
5 Push in the pull tab to lock it.
6 Reattach and close the battery door.
7 Attach the AC power cord to the rear of the cardiograph.
8 Plug the AC power cord into a grounded electrical outlet. Check that the green AC power indicator light on the front of the cardiograph is illuminated.
9 Charge the battery for at least 16 hours before mobile use. The cardiograph can operate on AC power while the battery is charging but it will charge at a slower rate.
Replacing the AC FuseThe AC fuse needs to be replaced when the cardiograph is plugged into AC power, but the green AC power indicator light on the front of the cardiograph does not illuminate.
Only use replacement AC fuses with Philips part number 453564000371 (see page 7-21) or use a 1.5 amp (250V) time-delay fuse the same size and configuration as the original fuse.Figure 7-2 Replacing the AC Fuse
To replace the AC fuse:
1 Unplug the cardiograph from AC power. Pull out the AC power cord from the AC power connector on the rear of the cardiograph.
2 Locate the AC fuse, which is directly below the AC power connector.
3 Push down on the center tab on the fuse and pull out the fuse from the fuse holder slot.
4 Insert the new fuse using the same orientation, with the center tab facing up.
5 Push the fuse all the way into the fuse holder slot. The fuse snaps into place.
PageWriter Trim Cardiograph Instructions for Use 7-9
![Page 214: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/214.jpg)
Cardiograph Care and Maintenance Replacing the Lead Wires on the PIM
Replacing the Lead Wires on the PIMTo replace the lead wires:
1 Disconnect the PIM from the PIM connector ( ) located on the rear of cardiograph.
2 Remove the lead wire(s) by pulling the connector up.
3 Match the lead wire labeling (on lead) with the same lead wire connector on the PIM. Replace the lead wire by snapping it into the connector.
7-10 PageWriter Trim Cardiograph Instructions for Use
![Page 215: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/215.jpg)
Maintenance Tests Cardiograph Care and Maintenance
4 Reattach the patient data cable to the PIM connector.
WARNING To ensure safety and prevent damage to the system, only connect the patient data cable to the correct PIM connector on the rear of the cardiograph.
Maintenance TestsPageWriter Trim II and III only
Maintenance tests and diagnostic utilities are included in Configuration. These tests are used to verify or to optimize cardiograph performance. They can be used as a first step to identify a technical problem with the cardiograph. For more information about these tests contact the nearest Philips Response Center (see page 7-24).
To open the Maintenance Test screen:
1 Turn the Trim Knob to highlight the Config button on the Command Toolbar.
NOTE Access to the Configuration screens may be password controlled (see page 2-40).
2 Push the Trim Knob to select the button. The Configuration screen appears.
3 Press and hold down the Alt key on the keyboard. Press the S key to select the System tab. The System screen appears.The five available tests appear as buttons under Diagnostics (right side of screen).
CONFIG
PageWriter Trim Cardiograph Instructions for Use 7-11
![Page 216: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/216.jpg)
Cardiograph Care and Maintenance Maintenance Tests
Figure 7-3 Diagnostic Tests
PIM Test
(page 7-13)
(page 7-17)
(page 7-13)
(page 7-14)
(page 7-14)
Barcode Test
Magcard Test
Printer Test
Network
7-12 PageWriter Trim Cardiograph Instructions for Use
![Page 217: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/217.jpg)
Maintenance Tests Cardiograph Care and Maintenance
PIM TestThis test is used to confirm that the Patient Interface Module (PIM) is communicating with the cardiograph. This test can be performed when the cardiograph displays Patient Interface Module error messages, or when the cardiograph is unable to acquire data from the PIM when the PIM patient data cable is securely attached to the PIM connector ( ) on the rear of the cardiograph.
If this test fails, it may indicate a problem with the PIM or with the PIM patient data cable. For further assistance, contact the nearest Philips Response Center (see page 7-24).
To perform the PIM Test:
1 Turn the Trim Knob to highlight the PIM Test button under Diagnostics.
2 Push the Trim Knob to select the button. The message Accessing PIM... appears. The PIM Test Result window appears and indicates that the PIM Test has passed, or that the cardiograph is unable to communicate with the PIM.
3 If the message PIM Test Passed appears, the PIM is communicating properly with the cardiograph. The OK button is highlighted. Push the Trim Knob to close the window.
4 If the message Please Check the Patient Interface Module appears, check that the PIM patient data cable is securely attached to the PIM connector on the rear of the cardiograph. If the patient data cable is securely attached to the PIM connector, but still fails the PIM Test, contact the nearest Philips Response Center for further assistance (see page 7-24).
Barcode Reader TestThe Barcode Reader Test is used with the optional barcode reader (see page 1-25). The barcode reader is used to enter Patient ID information by scanning a barcode. This test can be used to confirm that the barcode reader is accurately scanning barcode data. To perform the barcode reader test:1 Ensure that the barcode reader is securely attached to the barcode reader connector ( )
on the rear of the cardiograph. If the barcode reader is not attached to the cardiograph, press and hold down the On/Standby button for 3 seconds, then release it. The cardiograph shuts down. Connect the barcode reader to the barcode reader connector ( ) on the rear of the cardiograph. Press the On/Standby button. Follow the procedure to open the Maintenance Test screen, see page 7-11.
2 Turn the Trim Knob to highlight the Barcode Test button under Diagnostics.
3 Push the Trim Knob to select the button. The Barcode Reader test window appears.
4 Hold the barcode reader at a 45o angle and scan a test barcode.
5 The barcode data appears next to the Patient ID field. Review the barcode data to ensure that it is accurate. The OK button is highlighted. If the barcode data is accurate, push the Trim Knob to select the OK button. Turn the Trim Knob to highlight the Cancel button if the barcode data is incorrect. Try the test again. If the test fails a second or subsequent time, contact the nearest Philips Response Center for further assistance (see page 7-24).
PageWriter Trim Cardiograph Instructions for Use 7-13
![Page 218: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/218.jpg)
Cardiograph Care and Maintenance Maintenance Tests
Magnetic Card Reader TestThe Magnetic Card Reader Test is used with the optional magnetic card reader (see page 1-26). The magnetic card reader is used to scan a magnetic card in order to enter Patient ID information. This test can be used to confirm that the magnetic card reader is correctly reading data from a magnetic card.
To perform the magnetic reader test:
1 Ensure that the magnetic card reader is securely attached to the magnetic card reader connector ( ) on the rear of the cardiograph. If the magnetic card reader is not attached to the cardiograph, press and hold down the On/Standby button for 3 seconds, then release it. The cardiograph shuts down. Connect the magnetic card reader to the magnetic card reader connector ( ) on the rear of the cardiograph. Press the On/Standby button. Follow the procedure to open the Maintenance Test screen, see page 7-11.
2 Turn the Trim Knob to highlight the Magcard Test button.
3 Push the Trim Knob to select the button. The Magnetic Card Reader window appears.
4 Insert the magnetic card into the slot on the reader.
5 Leave the magnetic card in the slot for five seconds and then pull it out.
6 The magnetic card data appears next to the Patient ID field.
7 Review the data to ensure that it is correct. The OK button is highlighted. If the magnetic card data is accurate, push the Trim Knob to select the OK button. Turn the Trim Knob to highlight the Cancel button if the magnetic card data is incorrect. Push the Trim Knob to select the button. Try the test again. If the test fails a second or subsequent time, contact the nearest Philips Response Center for further assistance (see page 7-24).
Printer TestThe Printer Test is used to verify that the cardiograph printer is able to correctly print out the test page. Use this test to verify proper printer performance or when reports appear to have print quality errors.
To perform the print test:
1 Turn the Trim Knob to highlight the Printer Test button under Diagnostics.
2 Push the Trim Knob to select the button. The message Printing Test Page... appears and the test page prints out.
3 Review the printer test page at points A, B, C, and D as seen on Figure 7-4, on page 7-16.
Table 7-1 Printer Test Page Description
Test Point Description
A The stepped bars are sharp edged and printed cleanly without distortion or missing segments
B The spacing between the vertical lines is 25 mm with a discrepancy of no more or less than 2%
7-14 PageWriter Trim Cardiograph Instructions for Use
![Page 219: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/219.jpg)
Maintenance Tests Cardiograph Care and Maintenance
C The diagonal lines should be straight and printed cleanly without distortion or breaks in the lines
D The character set is printed cleanly without distortion or missing characters, and all characters are clearly legible
Table 7-1 Printer Test Page Description (continued)
PageWriter Trim Cardiograph Instructions for Use 7-15
![Page 220: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/220.jpg)
Cardiograph Care and Maintenance Maintenance Tests
Figure 7-4 Printer Test Page
AA
B
C
D
7-16 PageWriter Trim Cardiograph Instructions for Use
![Page 221: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/221.jpg)
Maintenance Tests Cardiograph Care and Maintenance
8 If the printer test page matches the printer test points as described in Table 7-2, the cardiograph has passed the printer test. If the printer test page does not match the printer test points, the cardiograph has failed the print test. If the cardiograph fails the printer test, contact the nearest Philips Response Center for further assistance (see page 7-24).
Network TestThe Network Test displays the configured network information for the cardiograph. All cardiograph network configuration is completed on the Network screen. From any Configuration screen, press and hold down the Alt key on the keyboard, and then press the N key to select the Network tab and to open the Network screen. Before performing the Network test, ensure that the LAN card is fully inserted into the PC card slot on the rear of the cardiograph, and that the LAN cable is fully inserted into the cable connector on the card.
WARNING Do not connect the LAN card to a network connector when the cardiograph is connected to a patient.
CAUTION Only use the shielded LAN cable provided with the PageWriter Trim cardiograph (Philips Part Number 989803138021). Do not use LAN cables with the cardiograph that have not been approved by Philips Medical Systems.
To perform the network test:
1 Turn the Trim Knob to highlight the Network button.
2 Press the Trim Knob to select the button. The Network Connection window appears. The configured network information for the cardiograph appears on the window.
3 Review the network data to ensure that it is correct. The Retry button is highlighted. If the network data does not display, push the Trim Knob. If the test fails a second or subsequent time, contact the nearest Philips Response Center for further assistance (see page 7-24).
4 If the network data displays correctly, turn the Trim Knob to highlight the Close button. Push the Trim Knob to select the button.
PageWriter Trim Cardiograph Instructions for Use 7-17
![Page 222: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/222.jpg)
Cardiograph Care and Maintenance Important Patient and Safety Information
Important Patient and Safety InformationThe PageWriter Trim cardiograph isolates all connections to the patient from electrical ground and all other conductive circuits in the cardiograph. This reduces the possibility of hazardous currents passing from the cardiograph through the patient’s heart to ground, and from other equipment connected to the patient passing through the leads into the cardiograph to ground.
WARNING Failure to follow these warnings could affect both patient and operator safety.
When operating the cardiograph on AC power, ensure that the cardiograph and all other electrical equipment connected to or near the patient are effectively grounded.
Use only grounded power cords (three-wire power cords with grounded plugs) and grounded electrical outlets. Never adapt a grounded plug to fit an ungrounded outlet by removing the ground prong. Use the equipotential post when redundant earth ground is necessary according to IEC 60601-1-1.
If a safe ground connection is not ensured, operate the cardiograph on battery power only.
The use of equipment that applies high frequency voltages to the patient (including electrosurgical equipment and some respiration transducers) is not supported and may produce undesired results. Disconnect the patient data cable from the cardiograph, or detach the leads from the patient prior to performing any procedure that uses high frequency surgical equipment.
Do not perform ST analysis on the R/T ECG screen display or on Rhythm reports when the 0.5 Hz Baseline Wander filter is applied.
If abnormal ECG data appears on the printed report, and the abnormal data does not have a physiological origin, perform the printer diagnostic test to assess printer performance.
When printing a Rhythm report, there may be a slight delay before the Rhythm report begins to print on the cardiograph. Rhythm printing is not completed in real-time.
Pace pulse tick marks will not print on an Auto ECG that uses simultaneous acquisition.
WARNING Do not touch accessible connector pins and the patient simultaneously.
Electrical shock hazard. Keep cardiograph, Patient Interface Module (PIM) and all cardiograph accessories away from liquids. Do not immerse cardiograph, PIM, or other accessories in any liquids.
Periodically inspect the patient data cable, lead wires, and AC power cord for any worn or cracked insulation to ensure that no inner conductive material is exposed. Discard worn accessories and replace them only with Philips Medical Systems accessories (see page 1-35).
Keep the patient data cable away from power cords and any other electrical equipment. Failure to do so can result in AC power line frequency interference on the ECG trace.
7-18 PageWriter Trim Cardiograph Instructions for Use
![Page 223: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/223.jpg)
Important Patient and Safety Information Cardiograph Care and Maintenance
The Philips Medical Systems patient data cable (supplied with cardiograph) is an integral part of the cardiograph safety features. Use of any other patient data cable may compromise defibrillation protection, degrade cardiograph performance, and may result in distorted ECG data.
Only qualified personnel may service the cardiograph or may open the cardiograph housing to access internal cardiograph components. Do not open any covers on the cardiograph. There are no internal cardiograph components that are serviced by the operator.
Do not use this cardiograph near flammable anesthetics. It is not intended for use in explosive environments or in operating rooms.
Do not touch the patient, the patient data cable, any unused patient leads, or the cardiograph during defibrillation. Death or injury may occur from the electrical shock delivered by the defibrillator.
Always use electrode gel with reusable electrodes during defibrillation as ECG recovery will be greater than 10 seconds. Philips Medical Systems recommends the use of disposable electrodes at all times.
Ensure that the electrodes or lead wires do not come in contact with any other conductive materials (including earth-grounded materials) especially when connecting or disconnecting electrodes to or from a patient.
Connecting multiple medical electrical equipment to the same patient may pose a safety hazard due to the summation of leakage currents. Any combination of instruments should be evaluated by local safety personnel before being put into service.
Portable medical equipment such as X-rays and MRI may produce electromagnetic interference that produces noise in the ECG signal. Move the cardiograph away from these potential sources of electromagnetic interference.
Do not pull on the paper while an ECG report is being printed. This can cause distortion of the waveform and can lead to potential misdiagnosis.
Only use the Philips Medical Systems AC power cord supplied with the cardiograph. Periodically inspect the AC power cord and AC power connector (rear of cardiograph, see page 1-9) to ensure that both are in a safe and operable condition. If the AC power cord or AC power connector is not in a safe or operable condition, operate the cardiograph on battery power and contact Philips Medical Systems for service.
The cardiograph has been safety tested with the recommended accessories, peripherals, and leads, and no hazard was found when the cardiograph is operated with cardiac pacemakers or other stimulators.
Do not connect any equipment or accessories to the cardiograph that are not manufactured or approved by Philips Medical Systems or that are not IEC 60601-1 approved. The operation or use of non-approved equipment or accessories with the cardiograph is not tested or supported, and cardiograph operation and safety are not guaranteed.
PageWriter Trim Cardiograph Instructions for Use 7-19
![Page 224: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/224.jpg)
Cardiograph Care and Maintenance Important Patient and Safety Information
The list of cables and other accessories with which Philips claims compliance with the emissions and immunity requirements of IEC standard 60601-1-2 are listed in “Supplies and Ordering Information” on page 1-35.
WARNING When using additional peripheral equipment powered from an electrical source other than the cardiograph, the combination is considered to be a medical system. It is the responsibility of the operator to comply with IEC 60601-1-1 and test the medical system according to the requirements. For additional information contact Philips Medical Systems.
WARNING Do not use non-medical peripherals within 1.83 meters or 6 feet of a patient unless the non-medical peripherals receive power from the cardiograph or from an isolation transformer that meets medical safety standards.
Only install Philips Medical Systems software on the cardiograph. The installation or use of software not approved by Philips Medical Systems is strictly prohibited and cardiograph safety and performance are not guaranteed.
Only use Philips Medical Systems replacement parts and supplies with the cardiograph. The use of non-approved replacement parts and supplies with the cardiograph is strictly prohibited. Cardiograph safety and performance are not guaranteed when non-approved replacement parts and supplies are used with the cardiograph.
Manual measurements of ECG intervals and magnitudes should be performed on printed ECG reports only. Do not make manual measurements of ECG intervals and magnitudes on the R/T ECG display since these ECG representations are scaled.
Only use patient electrodes that are approved by Philips Medical Systems. The use of non-approved patient electrodes may degrade cardiograph performance.
The Philips Medical Systems warranty is applicable only if you use Philips Medical Systems approved accessories and replacement parts. See “Supplies and Ordering Information” on page 1-35 for more information.
Before using the Patient Cable Arm with the cardiograph cart, properly install the counter weight on the cardiograph base.
Only use the shielded LAN cable provided with the PageWriter Trim cardiograph, Philips Part Number 989803138021. Do not use any other LAN cables with the PageWriter Trim cardiograph. Use of unapproved LAN cables may result in radiated emissions that exceed the limit specified by CISPR11 Class B.
The combined maximum weight that can be placed on the cardiograph cart shelf and the top surface of the cart cannot exceed 20 kg (44 lbs). Do not place more than the specified weight on the cardiograph top surface and shelf.
Do not connect any device to the RS-232 port on the rear of the cardiograph when the patient data cable is connected to a patient.
There are no cardiograph parts that can be sterilized.
7-20 PageWriter Trim Cardiograph Instructions for Use
![Page 225: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/225.jpg)
Supplies and Ordering Information Cardiograph Care and Maintenance
The cardiograph is not intended for direct, or invasive cardiac monitoring purposes.
Excessive, repetitive use of the cardiograph keyboard and the cardiograph Trim Knob may result in a risk of developing carpal tunnel syndrome.
Ensure that the patient data cable is tucked away from the cardiograph cart wheels when transporting the cardiograph. Ensure that the patient data cable does not present a hazard when pushing the cardiograph cart.
For information on the standard IEC 60601-2-51, please go to the Philips InCenter web site (incenter.medical.philips.com). For information on using the Philips InCenter web site, see page 1-4.
Supplies and Ordering InformationThe part numbers for all supplies for the PageWriter Trim cardiograph are listed in this section.
Ordering SuppliesAll supplies may be ordered on the web at:http://shop.medical.philips.com
Use the part numbers listed below for reference to ensure that the correct supplies are ordered.
PageWriter Trim Cardiograph Instructions for Use 7-21
![Page 226: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/226.jpg)
Cardiograph Care and Maintenance Supplies and Ordering Information
PageWriter Trim Cardiograph Supply Part Numbers
Patient Interface Module (PIM)
Part Number Description
989803130091 Patient Interface Module (AAMI)
989803130101 Patient Interface Module (IEC)
Replacement Fuse
Part Number Description
453564000371 1.5 amp (250 V) Time-Delay Fuse
Complete Lead Sets
Part Number Description
989803129161 Complete Lead Set (AAMI)
989803129191 Complete Lead Set (IEC)
Replacement Lead Sets and Accessories
Part Number Description
989803129141 Limb Lead Set, 99 cm/39 in (AAMI)
989803129151 Chest Lead Set, 61 cm/24 in (AAMI)
989803129171 Limb Lead Set, 99 cm/39 in (IEC)
989803129181 Chest Lead Set, 61 cm/24 in (IEC)
989803129201 Long Limb Lead Set, 137 cm/54 in (IEC)
989803129211 Long Chest Lead Set, 99 cm/39 in (IEC)
989803129221 Long Complete Lead Set (IEC)
Electrodes
Part Number Description
13943B Disposable cardiography electrode, resting diagnostic ECG
M2253A Disposable electrode, adult, resting ECG(not available in Japan)
40420A Disposable electrode, diagnostic, pre-gelled
13944B Wet Gel Foam Electrode, resting ECG
7-22 PageWriter Trim Cardiograph Instructions for Use
![Page 227: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/227.jpg)
Supplies and Ordering Information Cardiograph Care and Maintenance
Cardiograph AccessoriesFor more information on optional cardiograph accessories or to place an order, contact your Philips Sales Representative the Philips Response Center nearest you, see page 7-24.
989803129231 Alligator Clips for Disposable Tab Electrodes (AAMI)
989803129241 Alligator Clips for Disposable Tab Electrodes (IEC)
M2254A Tab electrode adapter
40431B Alligator Clip Adapter for 1/8 post
40498E Snap Lead Electrode (IEC)
40475A Snap Lead Electrode Adapter
40490E 15mm Suction Electrode
40421A Push-in Connect Welsh Electrode
40494E Limb Clamp Electrode C400 (4 per box)
40491E Limb Plate Electrode C400 (4 per bag)
40424A Limb Plate Electrode (4 pack)
14030A Strap Electrode, 14 inch limb (4 per pack)
Printer Paper
Part Number Description
M3707A Thermal Paper (100 sheets), A size (8.5 x 11 in/21.6 x 28 cm)
M3708A Thermal Paper (100 sheets) A4 size (8.27 x 11.69 in/21 x 29.69 cm)
Battery
Part Number Description
989803130151 PageWriter Trim Replacement Battery
Optional Cardiograph Accessories
Part Number Description
989803129931 Barcode Reader
Electrodes (continued)
Part Number Description
PageWriter Trim Cardiograph Instructions for Use 7-23
![Page 228: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/228.jpg)
Cardiograph Care and Maintenance Contacting a Philips Response Center
Contacting a Philips Response Center The Philips Response Center can assist with product troubleshooting and provide technical expertise to help with any issue with the PageWriter Trim cardiograph or any of its accessories.
For more information on the Philips Response Center go to:
www.medical.philips.com/main/services/response_center
989803129941 Magnetic Card Reader
989803127331 PC card (128 MB storage)
989803129961 SmartCard Reader
989803130131 Patient Cable Arm
989803142041 Wireless LAN Card
989803129951 LAN PCMCIA Network Card
989803145331 USB Memory Stick
989803144601 PageWriter Trim Cardiograph User Documentation CD (additional copies)
989803130111 PageWriter Trim Cardiograph Cart
989803130121 PageWriter Trim Cardiograph Cart Additional Shelf
989803127441 Optional Locking Drawer for Cardiograph Cart
989803127461 Modem Card (USA and Canada only)
989803138021 LAN Cable
Optional Cardiograph Accessories
Part Number Description
North America Response Centers
Country Telephone Number
Canada (800) 323 2280
Mexico 01 800 710 8128
Puerto Rico 1 787 754 6811
United States (800) 722 9377
7-24 PageWriter Trim Cardiograph Instructions for Use
![Page 229: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/229.jpg)
Contacting a Philips Response Center Cardiograph Care and Maintenance
South America Response Centers
Country Telephone Number
Argentina 54 11 4546 7698
Brazil 0800 701 7789
Chile 0800 22 3003
Columbia 01 8000 11 10 10
Peru 51 1 620 6440
Europe Response Centers
Country Telephone Number
United Kingdom 44 0870 532 9741Fax: 44 01737 23 0550
Austria 43 1 60101 820
Belgium 32 2 525 7102 (French)32 2 525 7103 (Flemish)
Czech RepublicMCR Response Center(located in The Netherlands)
31 40 2781619
Denmark 45 80 30 30 35
Finland 358 615 80 400
France 0 810 835 624
Germany 0180 5 47 5000
GreeceMCR Response Center(located in The Netherlands)
31 40 2781619
HungaryMCR Response Center(located in The Netherlands)
31 40 2781619
Italy 0800 232100
Netherlands 31 40 27 211 27
Norway 47 800 84 080
PageWriter Trim Cardiograph Instructions for Use 7-25
![Page 230: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/230.jpg)
Cardiograph Care and Maintenance Contacting a Philips Response Center
PolandMCR Response Center(located in The Netherlands)
31 40 2781619
RumaniaMCR Response Center(located in The Netherlands)
31 40 2781619
RussiaMCR Response Center(located in The Netherlands)
31 40 2781619
Slovak RepublicMCR Response Center(located in The Netherlands)
31 40 2781619
Spain 34 90 230 4050
Sweden 46 200 81 00 10
Switzerland 0800 80 3000 (German)0800 80 3001 (French)
Asia Response Centers
Country Telephone Number
Australia 1800 251 400
China 800 810 0038
Hong Kong 852 2876 7578
India 1600 112 444
Indonesia 62 21 7910040, ext 8610
Japan 81 (0)120 095 205
Korea 82 (0)2 3445 9010
Malaysia 1800 886 188
New Zealand 0800 251 400
Philippines 63 2 8162617 ext. 875
Singapore 1800 Philips
Taiwan 0800 005 616
Europe Response Centers (continued)
Country Telephone Number
7-26 PageWriter Trim Cardiograph Instructions for Use
![Page 231: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/231.jpg)
Contacting a Philips Response Center Cardiograph Care and Maintenance
Thailand 66 (0)2 614 3569
Africa and Middle East
Country Telephone Number
All countries MCR Response Center(located in The Netherlands)
31 40 2781619
Asia Response Centers (continued)
Country Telephone Number
PageWriter Trim Cardiograph Instructions for Use 7-27
![Page 232: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/232.jpg)
A
1Suppressed Borderline InterpretiveStatements
IntroductionThis Appendix includes a listing of all borderline interpretive statements that are suppressed using the Borderline Statement Suppression feature that is available with the Philips 12-Lead Algorithm version PH090A. This feature is not available with the algorithm version number PH080A.
For more information on the Philips 12-Lead Algorithm, including a listing of all interpretive, reason, and severity statements included in the Philips 12-Lead Algorithm, please see the Philips 12-Lead Algorithm Physician’s Guide on the User Documentation CD or download the file from the Philips InCenter web site (incenter.medical.philips.com). For information on using the Philips InCenter web site, see page 1-4.
Level 1 Suppressed StatementsThe following interpretive statements listed in Table A-1 are suppressed when the Level - 1 few setting is selected under the Analysis tab on the Configuration screen. For information on configuring the Borderline Statement Suppression feature, see "About the Borderline Statement Suppression Setting" on page 2-7.
Table A-1 Level 1 Setting - Suppressed Statements
Statement Code Interpretive Statement
BAVCD BORDERLINE AV CONDUCTION DELAY
BIVCD BORDERLINE INTRAVENTRICULAR CONDUCTION DELAY
CLAA CONSIDER LEFT ATRIAL ABNORMALITY
CRAA CONSIDER RIGHT ATRIAL ABNORMALITY
ET EARLY PRECORDIAL R/S TRANSITION
ETRSR1 RSR' IN V1 OR V2, RIGHT VCD OR RVH
LOWT BORDERLINE T WAVE ABNORMALITIES
LT LATE PRECORDIAL R/S TRANSITION
A-1
![Page 233: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/233.jpg)
Suppressed Borderline Interpretive Statements Level 1 Suppressed Statements
LVHQ CONSIDER LEFT VENTRICULAR HYPERTROPHY
LVOLFB BORDERLINE LOW VOLTAGE IN FRONTAL LEADS
NFAD NO FURTHER ANALYSIS ATTEMPTED DUE TO PACED RHYTHM
NFRA NO FURTHER RHYTHM ANALYSIS ATTEMPTED DUE TO PACED RHYTHM
QMAB ARTIFACT IN LEAD(S) AND BASELINE WANDER IN LEAD(S)
QMART ARTIFACT IN LEAD(S)
QMBW BASELINE WANDER IN LEAD(S)
REPB BORDERLINE REPOLARIZATION ABNORMALITY
RSR1 RSR' IN V1 OR V2, PROBABLY NORMAL VARIANT
RSRNV RSR' IN V1, NORMAL VARIATION
SDALP NONSPECIFIC ST DEPRESSION, ANTEROLATERAL LDS
SDANP NONSPECIFIC ST DEPRESSION, ANTERIOR LEADS
SDCU MINIMAL ST DEPRESSION
SDINP NONSPECIFIC ST DEPRESSION, INFERIOR LEADS
SDJ JUNCTIONAL ST DEPRESSION
SDM MINIMAL ST DEPRESSION
SEALP T ELEVATION, PROB NORMAL VARIATION, ANT-LAT
SEANP ST ELEV, PROBABLY NORMAL VARIATION, ANT LEADS
SEINP T ELEVATION, PROBABLY NORMAL VARIATION, INF
SPRB BORDERLINE SHORT PR INTERVAL
TAXAB BORDERLINE T WAVE ABNORMALITIES
TAXQT BORDERLINE T WAVE ABNORMALITIES
TTW1 TALL T, PROBABLY NORMAL VARIANT, ANT-LAT LDS
Table A-1 Level 1 Setting - Suppressed Statements (continued)
Statement Code Interpretive Statement
A-2 PageWriter Trim Cardiograph Instructions for Use
![Page 234: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/234.jpg)
Level 2 Suppressed Statements Suppressed Borderline Interpretive Statements
Level 2 Suppressed StatementsThe interpretive statements listed in Table A-1, “Level 1 Setting - Suppressed Statements,” on page A-1, and the interpretive statements listed in Table A-2 beginning on this page, are suppressed when the Level - 2 many setting is selected under the Analysis tab on the Configuration screen. For information on configuring the Borderline Statement Suppression feature, see “About the Borderline Statement Suppression Setting” on page 2-7.
Table A-2 Level 2 Setting - Suppressed Statements
Statement Code Interpretive Statement
AMI1 BORDERLINE R WAVE PROGRESSION, ANTERIOR LEADS
AMI3 Q WAVE IN V1
AXL BORDERLINE LEFT AXIS DEVIATION
AXR BORDERLINE RIGHT AXIS DEVIATION
BIVCDL BORDERLINE IVCD WITH LAD
CRHPI CONSIDER RVH OR POSTERIOR INFARCT
CRHPIR CONSIDER RVH OR PMI W/ SEC REPOL ABNORMALITY
CRPMI TALL R WAVE IN V2, CONSIDER RVH OR PMI
CRVH CONSIDER RIGHT VENTRICULAR HYPERTROPHY
IMI3 BORDERLINE INFERIOR Q WAVES
IMI4 CONSIDER LAFB OR INFERIOR INFARCT
IMI18 INFERIOR Q WAVES, PROBABLY NORMAL VARIATION
IRBBRV IRBBB, THE RSR' PATTERN MAY ALSO REFLECT RVH
LMI10 BORDERLINE LATERAL Q WAVES
LMI49 LATERAL Q WAVES, PROBABLY NORMAL VARIATION
LQTB BORDERLINE PROLONGED QT INTERVAL
LVHR56 LVH BY VOLTAGE
LVHR6 LVH BY VOLTAGE
LVHRS CONSIDER LEFT VENTRICULAR HYPERTROPHY
LVHRSI LVH BY VOLTAGE
LVHS12 LVH BY VOLTAGE
LVHTA CONSIDER LEFT VENTRICULAR HYPERTROPHY
LVHV LVH BY VOLTAGE
MSTEA MINIMAL ST ELEVATION, ANTERIOR LEADS
PageWriter Trim Cardiograph Instructions for Use A-3
![Page 235: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/235.jpg)
Suppressed Borderline Interpretive Statements Level 2 Suppressed Statements
MSTEAL MINIMAL ST ELEVATION, ANTEROLATERAL LEADS
MSTEI MINIMAL ST ELEVATION, INFERIOR LEADS
MSTEL MINIMAL ST ELEVATION, LATERAL LEADS
PLAA PROBABLE LEFT ATRIAL ABNORMALITY
PQAL BORDERLINE Q WAVE IN ANTEROLATERAL LEADS
PQAN BORDERLINE Q WAVE IN ANTERIOR LEADS
PQIN BORDERLINE Q WAVES IN INFERIOR LEADS
PQLA BORDERLINE Q WAVES IN LATERAL LEADS
PRAA PROBABLE RIGHT ATRIAL ABNORMALITY
REPBAL BORDERLINE REPOL ABNORMALITY, ANT-LAT LEADS
REPBAN BORDERLINE REPOL ABNORMALITY, ANT LEADS
REPBIL BORDERLINE REPOL ABNORMALITY, INF-LAT LEADS
REPBIN BORDERLINE REPOL ABNORMALITY, INFERIOR LEADS
REPBLA BORDERLINE REPOL ABNORMALITY, LATERAL LEADS
RVHS5 CONSIDER RIGHT VENTRICULAR HYPERTROPHY
RVHS6 CONSIDER RIGHT VENTRICULAR HYPERTROPHY
SD0AL MINIMAL ST DEPRESSION, ANTEROLATERAL LEADS
SD0AN MINIMAL ST DEPRESSION, ANTERIOR LEADS
SD0IN MINIMAL ST DEPRESSION, INFERIOR LEADS
SD0LA MINIMAL ST DEPRESSION, LATERAL LEADS
SD0NS MINIMAL ST DEPRESSION
SPR SHORT PR INTERVAL, ACCELERATED AV CONDUCTION
SQT SHORT QT INTERVAL
T0AL BORDERLINE T ABNORMALITIES, ANT-LAT LEADS
T0AN BORDERLINE T ABNORMALITIES, ANTERIOR LEADS
T0IN BORDERLINE T ABNORMALITIES, INFERIOR LEADS
T0LA BORDERLINE T ABNORMALITIES, LATERAL LEADS
T0NS BORDERLINE T WAVE ABNORMALITIES
TTW30 TALL T WAVES, PROBABLY NORMAL VARIANT
Table A-2 Level 2 Setting - Suppressed Statements (continued)
Statement Code Interpretive Statement
A-4 PageWriter Trim Cardiograph Instructions for Use
![Page 236: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/236.jpg)
B
1Specifications
Technical Specifications
ECG AcquisitionAuto (12 leads)
Rhythm (up to 12 leads)
Disclose (1 lead)
KeyboardFull alphanumeric capability
Screen Display 640 x 480 pixel resolution
Color TFT display
Patient Interface Module Remote, microprocessor-controlled module
Cardiograph CartThe cardiograph cart (optional accessory) has been tested for stability using the IEC 60601-1 test protocol.
The IEC 60601-1 protocol calls for the cardiograph cart to not tip over using a 10 degree angle of incline in any direction. It is possible to exceed this amount of incline when the cardiograph and cart are moved over a roadside curb or some other small but steep incline. Use care when moving the cardiograph cart.
Always remove the patient cable arm before transporting. Install the cart counterbalance prior to the installation of the Patient Cable Arm.
B-1
![Page 237: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/237.jpg)
Specifications Technical Specifications
Signal Processing/Acquisition
Sampling Rate
2,000 samples per second per electrode/lead
24 bit A/D conversion provides 5µV resolution
Auto Frequency Response0.05-150 Hz, 0.15-150 Hz, 0.5-100 Hz0.05-100 Hz, 0.15-100 Hz, 0.5-100 Hz0.05-40 Hz, 0.15-40, 0.5-40 Hz
Rhythm Frequency Response 0.05-150 Hz, 0.15-150 Hz, 0.05-150 Hz0.15-100 Hz, 0.05-40 Hz, 0.15-40 Hz
Filters AC noise
Baseline Wander
Artifact
High and Low Pass Frequency
Printer
Printer Resolution
High-resolution, digital-array printer using thermal-sensitive paper
200 dpi at 25 mm/sec (voltage axis) by 500 dpi (time axis)
Report Formats3x4 1R, 3R (Standard, Cabrera)
6x2 (Standard, Cabrera)
Panoramic 12 (Cabrera)
12x1(Standard, Cabrera)
Rhythm (up to 12 selected leads)
12-Lead Extended Measurements
Disclose (1 minute of continuous waveform data for 1 selected lead)
B-2 PageWriter Trim Cardiograph Instructions for Use
![Page 238: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/238.jpg)
Technical Specifications Specifications
Battery Operation
Capacity
Typically 30 ECGs on a single charge or 30 minutes of continuous rhythm recording
No fail operation during ECG printing
Recharge
Eight hours to full capacity
Network Connection10 Base-T IEEE 802.3 Ethernet LAN
FAX Capability (optional)Group 3, Class 1 or 2 fax modem protocol
Support for PCMCIA fax modem
Modem (optional for USA and Canada)V.90, K56flex, enhanced V.34, V.32bis, V.32, V.22 bis and below
Barcode Reader (optional)Reads Code 39 (standard and full ASCII) Symbology
Magnetic Card Reader (optional)Reads cards adhering to ISO 7810, 7811-1, -2, -3, -4, -5, and JIS X 6301 and X6302
ECG Storage 150 ECGs typical for the optional 128 MB PC card
PageWriter Trim II:
50 ECGs
PageWriter Trim III:
150 ECGs
ECG File FormatsXML and XML SVG
PageWriter Trim Cardiograph Instructions for Use B-3
![Page 239: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/239.jpg)
Specifications Technical Specifications
Power and EnvironmentClass I, continuous operation
Line Power
100-240 Vac, 50/60 Hz, 65 VA max
Environmental Operating Conditions 10° to 40°C (50° to 104°F)
15% to 80% relative humidity (non-condensing)
Up to 4,550 m (15,000 ft.) altitude
Environmental Storage Conditions0° to 50 °C (32° to 122°F)
15% to 90% relative humidity (non-condensing)
Up to 4,550 m (15,000 ft.) altitude
Cardiograph Dimensions 310 mm width x 388 mm depth x 176 mm height (12.2 x 15.3 x 6.9 inches)
Cardiograph Weight 7.38 Kilograms (16.3 pounds)
Cardiograph Shipping Container Dimensions603.2 mm (width) x 1016 mm (depth) x 742.95 mm (height) (23.74 x 40 x 29.25 inches)
Cardiograph Shipping Container Weight6.325 Kilograms (14 pounds)
Cardiograph Cart Dimensions416 mm (width) x 600 mm (depth) x 930 mm (height) (16.37 x 23.6 x 36.6 inches)
Cardiograph Cart Weight 21 Kilograms (46.29 pounds) without patient cable arm and counter weight installed on cart
B-4 PageWriter Trim Cardiograph Instructions for Use
![Page 240: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/240.jpg)
Safety and Performance Specifications
Cardiograph Cart Shipping Container Dimensions609.6 mm (width) x 736.6 mm (depth) x 1016 mm (height) (24 x 29 x 40 inches)
Cardiograph Cart Container Weight6.57 Kilograms (14.48 pounds)
Safety and PerformanceMeets or exceeds the following requirements for safety and performance:
IEC 60601-1: 1988 +A1:1991 +A2:1995 General Requirements for Safety including all National Deviations
IEC 60601-1-2: 2001 General Requirements for Safety Electromagnetic Compatibility
IEC 60601-2-25 1993 +A1:1999 Safety Of Electrocardiographs
CISPR 11:1997 Radio Frequency disturbance, Limits and Methods of Test
AAMI EC11: 1991 Diagnostic Electrocardiographic Devices
JIST 1202: 1998 Japanese Industrial Standard for Electrocardiographs
Electromagnetic Compatibility (EMC)Electromagnetic compatibility with surrounding devices should be assessed when using the PageWriter Trim cardiograph.
An electronic device can either generate or receive electromagnetic interference. Testing for electromagnetic compatibility (EMC) has been performed on the PageWriter Trim cardiograph according to the international standard for EMC for medical devices (IEC 60601-1-2). This IEC standard has been adopted in Europe as the European Norm (EN 60601-1-2).
The PageWriter Trim cardiograph should not be used adjacent to, or stacked on top of other equipment. If the PageWriter Trim cardiograph must be used adjacent to or stacked on top of other equipment, verify that the cardiograph operates in an acceptable manner in the configuration in which it will be used.
The cardiograph will not malfunction when used with electrosurgical equipment.
Fixed, portable, and mobile radio frequency communications equipment can affect the performance of medical equipment. See Table B-4 on page B-9. For more information on troubleshooting, see “Troubleshooting” on page 6-1.
Reducing Electromagnetic InterferenceThe PageWriter Trim cardiograph and accessories may become sensitive to interference from other RF energy sources including power lines. RF energy sources include other medical devices, wireless devices, information technology equipment, and radio/television
PageWriter Trim Cardiograph Instructions for Use B-5
![Page 241: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/241.jpg)
Specifications Electromagnetic Compatibility (EMC)
transmission. Should interference be encountered, as demonstrated by artifact on the ECG trace, attempt to locate the source by assessing:
if the interference is intermittent or constant?
does the interference occur only in certain locations?
does the interference occur only when in close proximity to certain medical devices?
does the ECG signal quality change dramatically when the AC power cord is unplugged?
Once the source of the interference is located, attempt to attenuate the EMC coupling path by distancing the cardiograph from the source of the interference as much as possible. If further assistance is needed, contact the Philips Response Center nearest you.
Table B-1 Guidance and Manufacturer’s Declaration: Electromagentic Emissions
The PageWriter Trim cardiograph is intended for use in the electromagnetic environment specified in the table below. The customer or the user of the PageWriter Trim cardiograph should assure that it is used in such an environment.
Emissions Test Compliance Electromagnetic Environment: guidance
RF EmissionsCISPR 11
Group 1 The PageWriter Trim cardiograph uses RF energy only for its internal function. Therefore, its RF emissions are very low are not likely to cause any interference in nearby electronic equipment.
RF EmissionsCISPR 11
Class B The PageWriter Trim cardiograph is suitable for use in all establishments, including domestic establishments and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes.
Harmonic EmissionsIEC 61000-3-2
Class A
Voltage fluctuations/flicker emissionsIEC 61000-3-3
Complies
Table B-2 Guidance and Manufacturer’s Declaration: Electromagnetic Immunity
The PageWriter Trim cardiograph is intended for use in the electromagnetic environment specified below. The customer or the user of the PageWriter Trim cardiograph should assure that it is used in such an environment.
Emissions Test Compliance Compliance Level
Electromagnetic Environment: guidance
Electrostatic Discharge (ESD)IEC 61000-4-2
+/- 6 kV contact+/- 8 kV air
Complies Floors should be wood, concrete, or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30%.
B-6 PageWriter Trim Cardiograph Instructions for Use
![Page 242: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/242.jpg)
Electromagnetic Compatibility (EMC) Specifications
Electrical Fast transient/burstIEC 61000-4-4
+/- 2 kV for power supply line +/- 1 kV for input/output lines
Complies Mains power quality should be that of a typical commercial or hospital environment.
SurgeIEC 61000-4-5
+/- 1 kV differential mode+/- 2 kV common mode
Complies Mains power quality should be that of a typical commercial or hospital environment.
Voltage dips, short interruptions and voltage variations on power supply input linesIEC 61000-4-11
<5% UT
(>95% dip in UT) for 0.5 cycle
40% UT
(60% dip in UT) for 5 cycles
70% UT
(>30% dip in UT) for 25 cycles
<5% UT
(>95% dip in UT) for 5 seconds
Complies Mains power quality should be that of a typical commercial or hospital environment. If the user of the PageWriter Trim cardiograph required continued operation during power mains interruptions, it is recommended that the PageWriter Trim be powered from an uninterruptable power supply or a battery.
Power frequency (50./60 Hz) magnetic field
3 A/m Complies Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment.
Note: UT is the a.c. mains voltage prior to application of the test level.
Table B-2 Guidance and Manufacturer’s Declaration: Electromagnetic Immunity (continued)
The PageWriter Trim cardiograph is intended for use in the electromagnetic environment specified below. The customer or the user of the PageWriter Trim cardiograph should assure that it is used in such an environment.
Emissions Test Compliance Compliance Level
Electromagnetic Environment: guidance
PageWriter Trim Cardiograph Instructions for Use B-7
![Page 243: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/243.jpg)
Specifications Electromagnetic Compatibility (EMC)
Table B-3 Guidance and Manufacturer’s Declaration: Electromagentic Immunity
The PageWriter Trim cardiograph is intended for use in the electromagnetic environment specified below. The customer or the user of the PageWriter Trim cardiograph should assure that it is used in such an environment.
Emissions Test IEC 60601Test Level
Compliance Level
Electromagnetic Environment: guidance
Portable and mobile RF communications equipment should be used no closer to any part of the PageWriter Trim, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter.Recommended separation distance
Where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in metres (m).Field strengths from fixed RF transmitters, as determined by an electromagnetic site surveya, should be less than the compliance level in each frequency rangeb. Interference may occur in the vicinity of equipment marked with the following symbol:
Conducted RFIEC 61000-4-6
3 Vrms150 kHz to 80 MHz
Complies
Radiated RFIEC 61000-4-3
3 Vrms80 MHz to 2,5 GHz
Complies
Note 1: At 80 MHz and 800 MHz, the higher frequency range applies.Note 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from surfaces, objects, and people.
d 3 5,3Vrms
P=
d 3 5,3V/m
P=
d 73V/m
P= 800 MHz to 2,5 GHz
80 MHz to 800 MHz
B-8 PageWriter Trim Cardiograph Instructions for Use
![Page 244: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/244.jpg)
Electromagnetic Compatibility (EMC) Specifications
a. Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) tele-phones and land mobile radios, amateur radios, AM and FM radio broadcast and TV broadcast can-not be predicted theoretically with accuracy. To assess the electromagnetic environment due tofixed RF transmitters, an electromagnetic site survey should be considered. If the measured fieldstrength in the location in which the PageWriter Trim cardiograph is used exceeds the applicableRF compliance level above, the PageWriter Trim cardiograph should be observed to verify normaloperation. If abnormal performance is observed, additional measures may be necessary, such asreorienting or relocating the PageWriter Trim cardiograph.
b. Over the frequency range 150 kHz to 80 MHz, field strengths should be less than [3] V/m.
Table B-4 Recommended Separation Distances Between Portable and Mobile RF Communications Equipment and the PageWriter Trim Cardiograph: for equipment and systems that are not life-supporting
The PageWriter Trim cardiograph is intended for use in the electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the PageWriter Trim cardiograph can help to prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the PageWriter Trim cardiograph as recommended below, according to the maximum output power of the communications equipment.
Rated Maximum Output Power of Transmitter W
Separation Distance According to Frequency of Transmitter (m)
0,01
150 KHz to 800 KHz 800 MHz to 2.5 GHz
d = 1.2 d = 2.3
0.1 m 0.2 m
0,1 0.4 m 0.7 m
1 1.2 m 2.3 m
10 4.0 m 7.0 m
100 12.0 m 23.0 m
For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.Note 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.Note 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by the absorption and reflection from structures, objects, and people.
P P
PageWriter Trim Cardiograph Instructions for Use B-9
![Page 245: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/245.jpg)
C
1Assembling the Patient Cable Arm
OverviewThis appendix provides instructions on assembling the optional patient cable arm. The patient cable arm is used to hold the Patient Interface Module (PIM). For information on ordering the patient cable arm, see page 7-21.
NOTE Pay close attention to all of the cautions included in this appendix.
The patient cable arm ships with four Phillips head screws, a cart base counterweight with two hex bolts, four cable clips, one small Phillips head lock screw, three hex bolts, and two hex wrenches. Figure C-1 Patient cable arm assembly kit
C-1
![Page 246: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/246.jpg)
Assembling the Patient Cable Arm Assembly Instructions
Assembly InstructionsTo assemble the patient cable arm:
1 Remove the cardiograph from the cart. For more information, see page 1-5.
2 Flip the cart upside down and place onto a plastic sheet to prevent scratches on the cart surface.
CAUTION Do not place pressure on the Patient Interface Module (PIM) holder when the cart is upside down.
3 Attach the cart base counterweight to either side of the cart base with the two hex bolts. The patient cable arm will be installed on the opposite side of the cart as the cart base counterweight.
CAUTION The cart base counterweight must be installed to the cart base before installing the patient cable arm.
C-2 PageWriter Trim Cardiograph Instructions for Use
![Page 247: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/247.jpg)
Assembly Instructions Assembling the Patient Cable Arm
4 Flip the cart upright.
5 Attach the patient cable arm base to the opposite side of the cart that the base counterweight is attached to.
CAUTION Do not install the patient cable arm base to the same side of the cart that the cart base counterweight is attached to.
PageWriter Trim Cardiograph Instructions for Use C-3
![Page 248: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/248.jpg)
Assembling the Patient Cable Arm Assembly Instructions
6 Insert the patient cable arm into the base.
7 Insert the small Phillips head lock screw into the base.
C-4 PageWriter Trim Cardiograph Instructions for Use
![Page 249: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/249.jpg)
Assembly Instructions Assembling the Patient Cable Arm
8 Remove the four Phillips head screws and panel from the Patient Interface Module (PIM) holder and set it aside.
9 Place the PIM in the holder and replace the panel.
PageWriter Trim Cardiograph Instructions for Use C-5
![Page 250: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/250.jpg)
Assembling the Patient Cable Arm Assembly Instructions
10 Replace the four Phillips head screws.
11 Clip the PIM patient data cable to the patient cable arm in four places.
C-6 PageWriter Trim Cardiograph Instructions for Use
![Page 251: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/251.jpg)
Assembly Instructions Assembling the Patient Cable Arm
12 Loosen the elbow hinge on the patient cable arm.
CAUTION Loosen the elbow hinge carefully. The patient cable arm will spring open suddenly.
13 Reattach the cardiograph to the cart. For more information, see page 1-5.
PageWriter Trim Cardiograph Instructions for Use C-7
![Page 252: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/252.jpg)
Index
#
1 minute Disclose report 5-2812 lead Rhythm report 5-2712-lead report
12x1 report with cabrera leads 5-223x4, 1R report 5-13x4, 1R report with cabrera leads and simultaneous acquisition 5-203x4, 3R report with standard leads 5-196x2 report with cabrera leads 5-21algorithm version number 5-16basic measurements 5-4calibration information 5-11configurable clinical information 5-8deleting from the Archive 4-16device identification number 5-17examples 5-18extended measurements 5-25faxing 4-11institution information 5-7interpretive statements 5-2non-standard lead gains 5-12order information 5-9overview 5-1pacing detection settings 5-13panoranic (Pan-12) 5-24Patient ID clinical information 5-5Patient ID information 5-6PH080A 5-16physician information 5-10printing in the Archive 4-10quality statements 5-3report information 5-10saving to the Archive 4-6speed and sensitivity settings 5-16time separator 5-13
12x1 report with cabrera leads 5-223x4, 1R report 5-1
cabrera leads and simultaneous acquisition 5-20
3x4, 3R report with standard leads5-196 lead Rhythm report 5-266x2 report with cabrera leads 5-21
A
AAMI electrode placement 3-3female diagram 3-6male diagram 3-5
AAMI leadspart number 1-35, 7-22
AC fusepart number 1-35, 7-22replacement 7-9
AC interferencetroubleshooting 6-14
AC powerindicator light not working 6-6troubleshooting 6-6
AC power indicator lightlocation 1-17troubleshooting 6-6
accessoriesordering information 1-35, 7-21part numbers 1-37, 7-23
acquisitiontime separator 5-13
algorithmversion number 5-16
algorithm version 2-3alligator clips
part number 1-36, 7-23Archive
context toolbar 4-7deleting 12-lead reports 4-16exporting reports in XML format 4-14faxing 12-lead report 4-11functions available 4-6opening the screen 4-7printing 12-lead reports 4-10saving 12-lead reports to 4-6searching Remote Site
with a wildcard character 4-15artifact
muscle 3-12artifact filter 2-30, 3-12
symbol on printed report 3-12attaching electrodes 3-3attaching the lead wires to the electrodes 3-7Auto ECG
setting preview and print options 2-23taking 3-25
B
barcode readerdiagnostic test 7-13entering Patient ID information 3-21part number 1-37, 7-23troubleshooting 6-6using 1-25
baseline wander filter 2-30, 3-12symbol on printed report 3-12
basic measurements 5-4on ECG report 5-4
batterybattery charge indicator on PageWriter Trim I 1-15battery charge indicator on PageWriter Trim II and III 1-16charge time before initial use 1-15, 7-9charging 7-7inaccurate battery level reading 6-6installing 1-14maintenance and care 7-6part numbers 1-37, 7-23replacement 7-8troubleshooting 6-6
borderline statement suppression feature 2-7
C
cablescleaning 7-2
cabrera leads12x1 report 5-223x4 report example 5-206x2 report 5-21panoramic (Pan-12) report 5-24
calibration pulse 5-11non-standard lead gains 5-12scaling 5-11shapes 5-11
caps lock feature 2-24cardiograph
identification number on printed report 5-17
cardiograph cartcart assembly C-1
cartassembly C-1installation instructions 1-3
cleaningapproved cardiograph cleaning solutions 7-1approved patient data cable cleaning solutions 7-2cables 7-2electrodes 7-2lead wires 7-2patient data cable 7-2
clinical informationon the printed report 5-5
codesethnicity 5-7
color-coded waveforms 3-10computer based training program 1-3configurable clinical information 5-8configuration 2-2connecting the Patient Interface Module to the cardiograph 1-12
Index-1
![Page 253: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/253.jpg)
connector portlocation 1-7
context-sensitive Helpusing on the cardiograph 3-33
customer servicetelephone numbers 1-38, 7-24
D
date formatsetting 2-41
default display format setting 2-25deleting 12-lead reports from the Archive 4-16Device ID
on printed report 5-17diagnostic test
barcode reader 7-13magnetic card reader 7-14Patient Interface Module (PIM) 7-13printer 7-14
Disclose1 minute report 5-28overview 3-30report examples 5-28
DNSconfiguring 2-38
Document Type Definition 4-14DTD (Document Type Definition) 4-14
E
ECGquality 3-2
ECG acquisitionconcurrent 5-13Disclose 3-30Rhythm 3-28simultaneous 5-13taking an Auto ECG 3-25
ECG report1 minute disclose 5-2812 lead Rhythm report 5-2712x1 report with cabrera leads 5-223x4, 1R report 5-13x4, 1R report with cabrera leads and simultaneous acquisition 5-203x4, 3R report with standard leads 5-196 lead Rhythm report 5-266x2 with cabrera leads 5-21algorithm version number 5-16basic measurements 5-4calibration information 5-11configurable clinical information5-8device identification number 5-17Disclose 5-28ECG order information 5-9examples 5-18exporting in XML format 4-14extended measurements 5-25faxing 4-11
institution information 5-7non-standard lead gains 5-12order information 5-9overview 5-1pacing detection settings 5-13panoramic (Pan-12) report 5-24Patient ID information 5-6
clinical information 5-5PH080A 5-16physician information 5-10printing in the Archive 4-10report information 5-10Rhythm 5-25speed and sensitivity settings 5-16STAT label 5-10time separator 5-13
ECG reportssaving to the Archive 4-6
editing Patient ID information 3-23electrode placement
female diagram 3-6male diagram 3-5
electrodesattaching to the patient 3-3, 3-6cleaning 7-2disposable part number 1-36, 7-22, 7-23
Emergency ECGs 3-24entering Patient ID information 3-17
with keyboard 3-19entering Patient ID information with the barcode reader 3-21ethnicity codes 5-7exporting reports
XML 4-14extended measurements report 5-25
F
faxconfiguring for a TraceMaster Remote Site 2-34
faxing 12-lead reports (from the Archive) 4-11filter
artifact 3-12frequency response 3-12frequency response AHA recommendations 3-12
filter settings button 2-30filters
artifactsymbol on printed report 3-12
as displayed on the printed report3-11baseline wander 3-12
symbol on printed report 3-12overview 3-11setting defaults 2-30
freezeresetting the cardiograph 6-17troubleshooting 6-16
frequency response filter 3-12AHA recommendation 3-12
Fridericia rate corrected QT interval2-3
G
green waveform 3-10
H
Helpusing on the cardiograph 3-33
I
ID information (Patient)editing 3-23entering on cardiograph 3-17on the printed report 5-6
IEC electrode placement 3-3female diagram 3-6male diagram 3-5
IEC leadspart number 1-35, 7-22
InCenter web siteerrors opening PDF documents 1-4using 1-4
institution information 5-7instructing the patient 3-2interactive training program 1-3
CD part number 1-37, 7-24interpretive, reason, and severity statements
overview 5-2
K
keyboardentering Orders 4-4entering Patient ID information 3-19
L
LAN Cardpart number 1-37, 7-23
LAN connectionconfiguring for a TraceMaster Remote Site 2-36
lead reversal detection feature 2-3lead wires
attaching 3-7chest leads part number 1-35, 7-22cleaning 7-2limb leads part number 1-35, 7-22replacing 7-10
leadspart numbers 1-35, 7-22
leads offtroubleshooting 6-9
limb leadsaxis measurements 5-4
limb plate electrodepart number 1-36, 7-23
Index-2
![Page 254: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/254.jpg)
loading configured cardiograph settings 2-47loose electrode
troubleshooting 6-16lost password 2-41
M
magnet paced 5-15magnetic card reader
diagnostic test 7-14entering Patient ID information 3-22, 3-23part number 1-37, 7-23using 1-26
maintenancebattery 7-6battery replacement 7-8replacing AC fuses 7-9tests 7-11
metric unitsconfiguring on cardiograph 2-41
modemconfiguring for a TraceMaster Remote Site 2-34
muscle artifact 3-12
N
navigation tips 1-27network connection
configuring 2-38configuring for a TraceMaster Remote Site 2-36
non-paced 5-14non-standard lead gains 5-12not known if paced 5-14Notification Message Feature 2-26
O
On/Standby buttonhow to use 1-18location 1-17
order information 5-9Order settings 2-28ordering information
supplies 1-35, 7-21Orders
configuring user defined information 2-17deleting 4-4entering with keyboard 4-4information on printed report 5-9using the Orders screen 4-2using to enter Patient ID information 3-19
overreading 5-10
P
P? 5-14paced 5-15pacemaker
and magnet 5-15
pacing detection settingsnon-paced 5-15not known if paced 5-14on the printed report 5-13overview 3-31paced 5-15paced (magnet) 5-15
PageWriter Trim IAC power cord connector location 1-7equipotential port location 1-7front view 1-6rear view 1-7
PageWriter Trim II and IIIAC power cord location 1-9barcode reader connector port location 1-9configuration 2-1
configuring multiple cardiographs 2-1opening the screen 2-2
configuration with a Philips TraceMasterVue ECG Management System 2-2configuring Auto report profiles2-17configuring date and time format2-41configuring default filters 2-30configuring network settings 2-38configuring password settings 2-40configuring Patient ID settings 2-8equipotential port location 1-9front view 1-8PC Card slot location 1-9rear view 1-9USB port location 1-9
panoramic (Pan-12) report 5-24paper
part number 1-37, 7-23part numbers
accessories 1-37, 7-23supplies 1-35, 7-22
password settingsconfiguring 2-40lost password 2-41
patient cable armpart number 1-37, 7-23
patient data cableapproved cleaning solutions 7-2cleaning 7-2diagnostic test 7-13
Patient ID clinical information 5-5Patient ID Information
on ECG report 5-5Patient ID information
changing 3-24clinical codes 5-5configurable clinical information5-8configuration options 2-8configuring default settings 2-8configuring user defined information 2-17deleting Pending Orders 4-4editing 3-23
entering on cardiograph 3-17entering Orders at cardiograph 4-4entering with keyboard 3-19entering with magnetic card reader 3-22, 3-23entering with the barcode reader3-21ethnicity codes 5-7loading Orders 4-2not entering to take STAT ECG 3-24on the printed report 5-6opening a Pending Order 3-19reviewing 3-24
patient instructionsbefore taking ECG 3-2
Patient Interface Module (PIM)assembly C-1diagnostic test 7-13how to connect to cardiograph 1-12overview 1-10part number 1-35, 7-22placing in holder 1-13replacing the lead wires 7-10storage 1-13
patient preparation 3-2skin preparation 3-3
patient sessionoverview 3-1steps 3-1
PC Cardinserting into cardiograph 1-24part number 1-37, 7-23removing from cardiograph 1-24using 1-21
Pending Orderusing to enter Patient ID information 3-19
PH080A 2-3, 5-16PH090A 2-3Philips 12-lead Algorithm
borderline interpretive statement suppression 2-7configuring default settings 2-3interpretive, reason, and severity statements on printed report 5-2severity codes 5-3suppressed borderline interpretive statement listing A-1version number on printed report5-16
Philips InCenter web site 1-4errors opening PDF documents 1-4using 1-4
Philips Response Centertelephone numbers 1-38, 7-24
Philips TraceMaster ECG Management System
searching a Remote Site 4-14physician information
on ECG report 5-10physician name
configuring option on Patient ID screen 2-14
PM 5-15
Index-3
![Page 255: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/255.jpg)
power indicator lightlocation 1-17
preparing the skin 3-3printed ECG lead standard setting 2-25printed report
3x4 report with standard leads 5-19algorithm version number 5-16basic measurements 5-4calibration information
5-11configurable clinical information5-8device identification number 5-17Disclose report 5-28examples 5-18extended measurements 5-25institution information 5-7non-standard lead gains 5-12order information 5-9overview 5-1pacing detection settings 5-13Patient ID information 5-6PH080A 5-16physician information 5-10quality statements 5-3red stripe appears 1-19, 7-4speed and sensitivity settings 5-16time separator 5-13
printerdiagnostic test 7-14
printer paperpart number 1-37, 7-23replacing 1-19, 7-4
printing the configuration settings report 2-48pulse calibration 5-11
Q
quality indicatorgreen waveform 3-10red dotted line 3-8, 3-10yellow waveform 3-10
quality statements 5-3query
remote 4-14Quick Search Fields feature 2-28
R
R/T ECGtaking an Auto ECG 3-25troubleshooting 6-16
reason statements 5-2remote query 4-14Remote Site
searching on the cardiograph 4-14searching with a wildcard character 4-15
replacingAC fuses 7-9battery 7-8
lead wires in the Patient Interface Module (PIM) 7-10printer paper 1-19, 7-4
report formatoverview 5-1
report information 5-10reports
overview 5-1resetting the cardiograph 6-17restoring factory default settings 2-48reviewing Patient ID information 3-24Rhythm 3-28
12 lead report 5-276 lead report 5-26using 3-28
Rhythm report 5-25Rhythm strips
recording 3-28
S
saving configured cardiograph settings 2-46serial number
locating on cardiograph 1-4severity statements 5-2
codes 5-3signal quality
checking 3-7color-coded waveforms 3-10indicators 3-7troubleshooting 6-14
simulated waveform data feature 2-27simultaneous acquisition
report example 5-20skeletal muscle artifact 3-12skin preparation
before taking ECG 3-3SmartCard Reader
part number 1-37, 7-23using 1-26
softwarenavigation tips 1-27upgrade feature 2-24
somatic tremorstroubleshooting 6-15
speed and sensitivity settings 5-16ST segment distortion
and Rhythm filter settings 2-32Standby
button location 1-17configuring default settings 2-25how to use 1-18
STAT ECGconfiguring Patient ID screen option 2-14label on the printed report 5-10taking 3-24
suppliesordering information 1-35, 7-21part numbers 1-35, 7-22
suppressed borderline interpretive statements
listing A-1system freeze
resetting the cardiograph 6-17troubleshooting 6-16
T
TCP/IPconfiguring 2-38
technical specifications B-1tests
diagnostic 7-11maintenance 7-11
time formatsetting 2-41
time separator 5-13token label 1-9TraceMaster ECG Management System
configuring network connection2-38troubleshooting 6-2
TraceMasterVue ECG Management System
configuring with cardiograph 2-2training program 1-3transferring reports
XML 4-14troubleshooting
AC power 6-6AC power indicator light 6-6barcode reader 6-6battery 6-6leads off 6-9loose electrode 6-16Philips Response Center phone numbers 1-38, 7-24red stripe on printed report 1-19, 7-4signal quality 6-14somatic tremors 6-15system freeze 6-16wandering baseline 6-15
U
Unconfirmed Diagnosislabel on printed report 5-10
UPIN (Universal Physician Identification Number)
on the printed report 5-10USB memory stick 1-24user documentation CD
part number 1-37, 7-24
W
wandering baselinetroubleshooting 6-15
waveformgreen 3-10
Index-4
![Page 256: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/256.jpg)
waveform size and sensitivity settingsprinted report 5-16
Welsh electrodespart number 1-36, 7-23
wildcard character search 4-15WINS
configuring 2-38wireless LAN
installation instructions 1-3wireless LAN option 1-22waveform
yellow 3-10
X
XMLexporting reports 4-14
XML information 1-3XMT 4-7
Y
yellow waveform 3-10
Index-5
![Page 257: 679-1E - Page Writer Trim I%2C II%2C III Cardiograph Instructions for Use for a%2E01](https://reader034.vdocuments.net/reader034/viewer/2022051210/54e9c4b04a795910478b492d/html5/thumbnails/257.jpg)
Philips Medical Systems3000 Minuteman RoadAndover, MA 01810 USA PageWriter Trim I, II, III CardiographInstructions For UseM4992-91150 Edition 4