7 flat slabs
TRANSCRIPT
CE 5510 - 2004
Advanced Structural Concrete Design
CE 5510 - 2004
Flat Slab System
• Column Heads • Division of Panels • Deflection • Crack Control • Shear • Arrangement of Reinforcement
CE 5510 - 2004
Class Objectives
•Identify the types of slab construction, summarizing the advantages and disadvantages of each
•Explain the methods of analysis of slabs•Determine the design moments of one-way and two way
slabs •Design of flat slabs covering:
division into strips, edge and corner columns, punching shear and provision of shear reinforcement
CE 5510 - 2004
Recommended Reading• James G. MacGregor, “REINFORCED CONCRETE:
Mechanics and Design”, 3rd Ed., Prentice-Hall, 1997, Ch. 13 and 14.
• Allen, A. H., “REINFORCED CONCRETE DESIGN TO BS8110 SIMPLY EXPLAINED”, E&FN Spon, London 1988, Ch. 14
•The next few slides are from the Reinforced Concrete Council
CE 5510 - 2004
Types of slabs
CE 5510 - 2004
CE 5510 - 2004
CE 5510 - 2004
Flat Slab
CE 5510 - 2004
CE 5510 - 2004
CE 5510 - 2004
Analysis of Slabs
course
CE 5510 - 2004
One-way spanning slab
CE 5510 - 2004
Simplified
CE 5510 - 2004
Two way action – A rectangular panel supported on all four side
• Curvature more severe along lx
• Moment is short span higher
• Evaluation of moment is complex as behaviour is highly indeterminate
CE 5510 - 2004
Consider two strips AB and ED at mid-span. Deflection at central point C is the same.
4Deflection of udl beam = 5wl 384EI
=∆ kwl 4
CE 5510 - 2004
4∆AB = k nAB ly
4∆DE = k nDE lx
nAB and nDE are portions of total load intensity transferred to AB and DE respectively.
Since ∆AB = ∆DE ,
4 4wl wl == nDE 4
y 4
nAB l 4 +x
l 4 l + ly x y x
CE 5510 - 2004
nDE > nAB
Shorter span strip, DE, supports heavier portion of load and is subject to larger moment.
Assumption – supports are unyielding
If the supports of the single panel is flexible, e.g. beams,columns, etc. the distribution of moment is more complex. Degree of stiffness of yielding support determines theintensity of the steepness of the curvature contours in thelx and ly direction and redistribution of moments.
CE 5510 - 2004
Two-way spanning slab
CE 5510 - 2004
CE 5510 - 2004
Mid Span Moments - corner supported
CE 5510 - 2004
Approximate moment in one direction in slabs supported on columns at corners
CE 5510 - 2004
Midspan moment - edge supported
CE 5510 - 2004
Approximate distribution of moment in one direction in slabs with symmetrical supports on four sides
CE 5510 - 2004
Moment
CE 5510 - 2004
Restrained Corners
CE 5510 - 2004
Table of Values
CE 5510 - 2004
Table of Coefficients
CE 5510 - 2004
Adjusted
CE 5510 - 2004
Flat Slabs
CE 5510 - 2004
Flat Slabs - Analysis
CE 5510 - 2004
CE 5510 - 2004
CE 5510 - 2004
Flat Slab - Moments
CE 5510 - 2004
Widths
CE 5510 - 2004
Distribution
CE 5510 - 2004
Flat Slab – Moment Transfer
CE 5510 - 2004
U-Bars
CE 5510 - 2004
Flat Slab – Moment Transfer
CE 5510 - 2004
What does it depend on?
CE 5510 - 2004
CE 5510 - 2004
Edge Beams
CE 5510 - 2004
Flat Slab - Shear
CE 5510 - 2004
CE 5510 - 2004
Effective Shear Force
CE 5510 - 2004
Deflection
CE 5510 - 2004
Shear Reinforcement
CE 5510 - 2004
Due to the limited depth special reinforcement are required involving the use of shear heads and anchor bars and wires.
CE 5510 - 2004
2004CE 5510
CE 5510 - 2004
CE 5510 - 2004
CE 5510 - 2004
CE 5510 - 2004
CE 5510 - 2004
2004CE 5510
CE 5510 - 2004
CE 5510 - 2004
CE 5510 - 2004
CE 5510 - 2004
CE 5510 - 2004
CE 5510 - 2004
CE 5510 - 2004
CE 5510 - 2004
CE 5510 - 2004
CE 5510 - 2004
CE 5510 - 2004