7 zigbee based wsn and service robot into an intelligent ... based wsn an… · zigbee based wsn...
TRANSCRIPT
Zigbee Based Wsn And Service Robot Into An Intelligent Home System Using Arm 7, Kajal R.
Gat, Prof. V.G.Puranik, Journal Impact Factor (2015): 8.9958 (Calculated by GISI)
www.jifactor.com
www.iaeme.com/ijecet.asp 48 [email protected]
1Student, Department of Electronics and Telecommunication Vishwabharti Academy’s College of
Engineering Ahmednagar, Sarola Baddi, Ahmednagar-414201, India
2Assistant Professor, Department of Electronics and Telecommunication Vishwabharti Academy’s
College of Engineering Ahmednagar, Sarola Baddi, Ahmednagar-414201, India,
ABSTRACT
In this paper, smart home system is implemented using Wireless Sensor Network (WSN) and
Service Robot. This system is low cost, low power and multifunctional based on Zigbee technology.
The Zigbee technology is used for wireless communication protocol. Devices such as Temperature
sensor, LDR sensor, Humidity sensor, Gas sensor, Light Fan, DC motor, GPRS Modem and buzzer
are integrated in the system of the smart home system. Service Robot is used in smart home system.
Robot is used for household application i.e. for picking and placing operation. Sensor node consists
of sensing and processing and communication. Wireless Sensor Nodes communicate each other by
wirelessly.
Keywords: Camera, GPRS, LPC2148, PC, Sensors, Service robot, Smart home system, Wireless
sensor network, Zigbee.
I. INTRODUCTON
Smart environment is a physical world that is connected to a network.WSN uses various
sensor nodes. Sensor nodes consist of sensors and actuators. Generally this system improves the life
quality of physical disabilities and aged person.WSN consists of few to thousands nodes and each
node are connected to each other.
This system is low power and low cost system so only two senor nodes are used. Robot is
used for home application. Various Wireless technologies are available. Here Zigbee technology is
used.
ZIGBEE BASED WSN AND SERVICE ROBOT INTO AN INTELLIGENT
HOME SYSTEM USING ARM 7
Kajal R. Gat1, Prof. V.G.Puranik
2
Volume 6, Issue 6, June (2015), pp. 48-56
Article Id: 40120150606007
International Journal of Electronics and Communication
Engineering & Technology (IJECET)
© IAEME: Http://www.iaeme.com/ijecet.asp
ISSN 0976 – 6464(Print) ISSN 0976 – 6472(Online)
IJECET
© I A E M E
Zigbee Based Wsn And Service Robot Into An Intelligent Home System Using Arm 7, Kajal R.
Gat, Prof. V.G.Puranik, Journal Impact Factor (2015): 8.9958 (Calculated by GISI)
www.jifactor.com
www.iaeme.com/ijecet.asp 49 [email protected]
Fig 1: Wireless Sensor Network
II. RELETED LITERATURE
Basically this project can be differentiate by 3 main technology such as PC, Zigbee wireless
technology and LPC 2148 which play an important roles to develop a better, compatible, user
friendly and cost efficient smart home system than other existing system. In general, this project
consists of two major parts that need to be developed; Hardware and software. For the hardware part
it consists of system board which includes LPC2148, Zigbee, sensors, GPRS modem and some basic
electronic components.
A. Practical design of intelligent living-space based on Bluetooth System:
In this paper, intelligent home system based on Bluetooth technology as practically design
and implemented in a living room, which was supported by the Taiwan Education Ministry under
“Projects of Improving Teaching Superiority Taiwan colleges”[3].
B. Zigbee based home automation wireless sensor network:
This paper describes the Zigbee standard for wireless sensor network [4].
C. Bluetooth Remote Home Automation System Using Android Application:
In this paper, Home automation system is based on Bluetooth technology by using android
application. Bluetooth technology is to provide access from smart home.
D. Human Machine Interface:
The smart home application is deals with machine-oriented communications (MOC). The
term MOC means technical systems construction principle where interaction of two or more entities
and at least one entity does not necessarily require human interaction or intervention in the
communication process. So, the main part of the modern smart home functions relates to the scope of
MOC.
Zigbee Based Wsn And Service Robot Into An Intelligent Home System Using Arm 7, Kajal R.
Gat, Prof. V.G.Puranik, Journal Impact Factor (2015): 8.9958 (Calculated by GISI)
www.jifactor.com
www.iaeme.com/ijecet.asp 50 [email protected]
III. SYSTEM DEVELOPMENT
By studying the existing technology of smart home system but there are many drawbacks so
this system is proposed. This system is low cost and multifunctional also low power is required.
Wireless Sensor Network to create a smart system.WSN consists of two nodes i.e. Master
node and Slave node.WSN used for communication purpose. So various sensor nodes placed in
home system. Home section is divided in two sections: Room Section and Pick and Place Robot
Section Master nodes means Room section and Slave nodes means Pick and place robot section. In
Room section various sensors are implemented such as Temperature sensor, LDR sensor, Humidity
sensor, Gas sensor. Zigbee Transmitter connected in Room section. All sensor values are indicated
on display but when critical condition arises particular action will takes place.
When Temperature value increases above threshold value then buzzer will alarm
simultaneously display “HIGH TEMPERATURE” and Fan is ON till temperature will slow down.
When gas is detected buzzer will alarm and display “smoke detected” on LCD Display.LDR sensor
indicates normal value but when threshold voltage increases light will be on and display sensor
value. Humidity sensor indicates normal value but when humidity increases buzzer will alarm and
display sensor value. All this data posted to web page through GPRS server.
Slave node means pick ad place robot section, in this section Zigbee receiver is connected. In
this section robot is used as picking and placing purpose. Robot will perform various actions like
left, right, up, down, open, close, front, back and stop.
RF wireless camera mounted on robot section for live video monitoring through PC or
Laptop.
Fig 2: Block diagram of Room Section
Zigbee Based Wsn And Service Robot Into An Intelligent Home System Using Arm 7, Kajal R.
Gat, Prof. V.G.Puranik, Journal Impact Factor (2015): 8.9958 (Calculated by GISI)
www.jifactor.com
www.iaeme.com/ijecet.asp 51 [email protected]
Fig 3: Block diagram of Pick and Place Robot Section
A. LPC 2148 Microcontroller
• The LPC2141/42/44/46/48 microcontrollers are based on a 16-bit/32-bit ARM7TDMI-S.
• Flash memory ranging from 32 kB to 512 kB.
• Tiny size and low power consumption,.
• Serial communications interfaces ranging from a USB 2.0 Full-speed device, multiple UARTs,
SPI, SSP to I2C-bus and on-chip SRAM of 8 kB up to 40 kB, make these devices very well
suited for communication.
• Various 32-bit timers, single or dual 10-bit ADC(s), 10-bit DAC, PWM channels and 45 fast
GPIO lines.
• Suitable for industrial control and medical systems.
B. ZIGBEE Technology
• ZigBee is a high-level communication protocols.
• ZigBee is based on an IEEE 802.15.4 standard.
• Though its low power consumption limits transmission distances to 10–100 meters line-of-
sight, depending on power output and environmental characteristics,.
• ZigBee is typically used in low data rate applications that require long battery life and secure
networking.
• ZigBee has a defined rate of 250 kbit/s,.
C. GPRS Module
• GPRS (General packet radio service) is expected to profoundly change the mobile data
services that GSM, CDMA and TDMA network operators can offer.
• GPRS will increase opportunities for higher revenues the number of kilobytes of data
transferred).
• GPRS combines mobile access with Internet protocol (IP)-based services, using packet data
transmission that makes highly efficient use of radio spectrum and enables high data speeds.
• It gives users increased bandwidth, making it possible and cost-effective to remain constantly
connected, as well as to send and receive data as text, graphics and video.
Zigbee Based Wsn And Service Robot Into An Intelligent Home System Using Arm 7, Kajal R.
Gat, Prof. V.G.Puranik, Journal Impact Factor (2015): 8.9958 (Calculated by GISI)
www.jifactor.com
www.iaeme.com/ijecet.asp 52 [email protected]
D. Flow Chart
Fig 4: Flow Chart for Room Section Fig 5: Flow Chart for Robot Section
IV. RESULT & DISCUSSION
The system evaluation the following conditions are analyzed.
Table 1: Sensor Conditions
SENSOR NORMAL CONDITION CTRITICAL CONDITION ACTION
Temperature 0-40 >40 Fan ON
LDR >200 <200 Light ON
Gas LOGIC 1 LOGIC 1 Buzzer ON
Humidity <50 >50 Buzzer ON
Zigbee Based Wsn And Service Robot Into An Intelligent Home System Using Arm 7, Kajal R.
Gat, Prof. V.G.Puranik, Journal Impact Factor (2015): 8.9958 (Calculated by GISI)
www.jifactor.com
www.iaeme.com/ijecet.asp 53 [email protected]
Fig 6: Display all sensor values
Fig 6 shows that when Light Dependent Resistor Sensor below threshold value i.e <200 then
Light is ON.
Fig 7: When LDR<200, Light ON
Fig 7 shows When temperature increases above its threshold value then Display “high
temperature”. and Fan is ON while temp is lower down.
Fig 8: When temperature increases above its threshold value
Fig 9: Fan ON
In figure 9 Gas values increases above a threshold value, it displayed “Smock Detected” on
lcd display also Buzzer ON.
Fig 10: Gas values increases above its threshold value
Zigbee Based Wsn And Service Robot Into An Intelligent Home System Using Arm 7, Kajal R.
Gat, Prof. V.G.Puranik, Journal Impact Factor (2015): 8.9958 (Calculated by GISI)
www.jifactor.com
www.iaeme.com/ijecet.asp 54 [email protected]
In pick and place robot section, robot is used as picking and placing purpose. Robot will
perform various actions like left, right, up, down, open, close, front, back and stop.
Fig 11: Key 3 press for STOP operation
In ROOM section GPRS modem is used. All this data posted to web page through GPRS
server.
Fig 12: Data Display on GPRS server
RF camera mounted on its top of robot and continuously live video monitors the PC/LAPTOP
Fig 13: Real time image of wireless camera
Zigbee Based Wsn And Service Robot Into An Intelligent Home System Using Arm 7, Kajal R.
Gat, Prof. V.G.Puranik, Journal Impact Factor (2015): 8.9958 (Calculated by GISI)
www.jifactor.com
www.iaeme.com/ijecet.asp 55 [email protected]
V. HARDWARE SETUP
Fig 14: Room Section
Fig 15: Pick and place Robot Section
VI. CONCLUSION
In this paper, we implement a smart home system using WSN and service robot. This system
is low power, low cost and improved security level. This system is useful in various purpose like
Military target tracking, Health care monitoring, Environment control systems and Smart Homes.
We can implement this system using ARM 11 also.
VII. ACKNOWLEDGMENT
I am very much thankful to the most respected Prof V.G. Puranik Department of Electronics
and telecommunication VACOEA who at very discrete step in study of this subject, contributed his
valuable guidance and helped to solve every problem that arise. I am very much thankful to HOD
Prof. V.S. Dhongde, for her persistent inspiration. I would like to extend my special thanks to
Principal Dr. A.K. Kureshi for spending his valuable time to go through my report and providing
many helpful suggestions.
Zigbee Based Wsn And Service Robot Into An Intelligent Home System Using Arm 7, Kajal R.
Gat, Prof. V.G.Puranik, Journal Impact Factor (2015): 8.9958 (Calculated by GISI)
www.jifactor.com
www.iaeme.com/ijecet.asp 56 [email protected]
REFERENCES
1. Soares, S.G., Tak a o, T.B., da Rocha, A., Ara u jo, R.A.M., and Barbosa, T.A.: Building
Distributed Soft Sensors, International Journal of Computer Information Systems and
Industrial Management Applications, 2011, 3, pp. 202-209.
2. Sharma, U., and Reddy, S.: Design of Home/Office Automation using Wireless Sensor
Network, International Journal of Computer Applications, 2012, 43(22), pp. 46-52
3. Chun-Liang Hsu, Teng-Yaw Hsu, Kuan-Yen Ho, and Wei-Bin WU from E.E Department of
Saint John’s University No. 499, Sec. 4, Tang-kin Rd. Taipei County, Taiwan REPUBLIC OF
CHINA
4. Michal VARCHOLA, Milos DRUTAROVSKY, Department of Electronics and Multimedia
Communications, Technical University of Kosice..
5. LI Li, LIU Yuan-an, TANG Bi-hua: SNMS: an intelligent transportation system network
architecture based on WSN and P2P network,” The Journal of China universities of posts and
telecommunications, 2007, 14(1) pp. 65-70.
6. R. Szewczyk, A. Mainwaring,J. Polastre,D.Culler. :An analysis of a large scale habitat
monitoring application, Proceedings of the Second ACM conference on Embedded Networked
Sensor Systems (SenSys), 2004,pp.214–226.
7. Lingaraj.K, Lokesh.K.S, Nagaveni.V.Biradar and Chowdari.K.K, “Research on Key Pre-
Distribution Scheme of Wireless Sensor Networks” International journal of Electronics and
Communication Engineering &Technology (IJECET), Volume 4, Issue 2, 2013, pp. 23 - 30,
ISSN Print: 0976- 6464, ISSN Online: 0976 –6472.
8. Sachin Gajjar, Mohanchur Sarkar and Kankar Dasgupta, “Performance Analysis of Clustering
Protocols For Wireless Sensor Networks” International journal of Electronics and
Communication Engineering &Technology (IJECET), Volume 4, Issue 6, 2013, pp. 107 - 116,
ISSN Print: 0976- 6464, ISSN Online: 0976 –6472.
9. Sarang D. Patil. and Prof. S.N. Pawar, “Wireless AMR System Using Zigbee Technology”
International journal of Electronics and Communication Engineering &Technology (IJECET),
Volume 3, Issue 2, 2012, pp. 107 - 115, ISSN Print: 0976- 6464, ISSN Online: 0976 –6472.
10. Miss. Smita B. Garde and Prof. S.L.Kotgire, “Coalmine Safety System With Zigbee
Specification” International journal of Electronics and Communication Engineering
&Technology (IJECET), Volume 4, Issue 2, 2013, pp. 504 - 512, ISSN Print: 0976- 6464,
ISSN Online: 0976 –6472.