703n

8/10/2019 703N

1/21

TL-WR703N setup guide one 3G router mode

TL-WR703NIs a new generation of mini 3G wireless router, compatible with the mainstream 3G standard - CDMA2000 (China

Telecom), WCDMA (China Unicom), TD-SCDMA (China Mobile). By using the device to meet people to share 3G wireless

broadband purposes.

Here we introduce the 3G TL-WR703N routing mode configuration.

TL-WR703NQuick setup:

Set by the Setup Wizard

Open the Device Management page "192.168.1.1", click "Setup Wizard", select "Next", optional equipment, there are three

access modes: 3G router mode, the wireless router mode, the wireless AP mode, the default route for the 3G model.

Here we choose "3G router mode", click "Next", 3G dial-up configuration parameters, select the region "China", the mobile ISP:

optional, "China Telecom", "China Mobile" and "China Unicom" (according to your Internet card formats to choose), the other

default settings do not change.

http://dc311.4shared.com/doc/IpDL_-oJ/preview.html

21 11/4/2012 2:33

8/10/2019 703N

2/21

TL-WR703NDefault has built in China Telecom, China Unicom mobile and dial the relevant parameters, in general, as

shown in the figure need only select the ISP operator interface can be automatically set to dial numbers, APN user name and

password and other information.

Click "Next" to set the wireless security.

Wireless Status: Wireless router, you must choose to open, so that the wireless network can access and host access to the

entire network.


21 11/4/2012 2:33

8/10/2019 703N

3/21

8/10/2019 703N

4/21

TL-WR703N setting guide TwoWireless router mode

Under router modeTL-WR703Nis equivalent to a wireless router, wired port as a WAN port, wireless-LAN, all the wireless

clients can share a broadband Internet line. The typical network application structure as shown below.

Here TL-WR703N Router Quick Setup mode method.

One: TL-WR703N settings

Step 1: In the browser, enter "192.168.1.1", enter the login ID and password are admin, open the TL-WR703N management

interface, automatic pop-up "Setup Wizard" (the management interface can also click the menu "Setup Wizard"), as shown

below.

Step 2: Click "Next" to start setting up the wireless mode setting page as shown below.


21 11/4/2012 2:33

8/10/2019 703N

5/21

Step 3: Select the "Router", click Next to bring up the wireless settings page, as shown below.

Step 4:: According to the decision to choose the front-end broadband connections to the Internet the way, if you can enter

recommended items. In this case the PPPOE example.

Step 5: Enter the broadband "Internet Account" and "Internet password", hit "Next", as shown below.


21 11/4/2012 2:33

8/10/2019 703N

6/21

AS shown on the above page, you can set TL-WR703N the SSID (wireless network name that TP-LINK_531984). To prevent

unauthorized users rub network, it is recommended to set the wireless security is recommended to select

"WPA-PSK/WPA2-PSK" and set the PSK password (in this case 123456789).

Step 6: Click "Next" prompt to restart the device, as shown below.

Click "Restart", automatically restarting the router, setup is complete.

Step 7: Restart completed at this time TL-WR703N wireless network already set up wireless security, the computer's wireless

network connection is automatically disconnected, reconnect the TL-WR703N need a wireless network (in this case the SSID to

TP-LINK_531984), the connection process to enter TL-WR703N wireless PSK password (in this case 123456789), connected

to, the following figure.


21 11/4/2012 2:33

8/10/2019 703N

7/21

If "WAN port state" view has access to the router to the IP and DNS server address, the PPPoE dial-up success.

Thus TL-WR703N the Router mode has been configured, and successfully connected to the Internet, wireless networks have

been set WPA-PSK/WPA2-PSK wireless security. Computer has wireless connectivity to the Internet router, the other computer

simply connect the TL-WR703N can normally access.


21 11/4/2012 2:33

8/10/2019 703N

8/21

TL-WR703N Setup guide ThreeWireless AP mode

AP mode using the wireless coverage capabilities for traditional wired LAN to provide wireless access to extension.

First, connect TL-WR703Nwith front-end wired LAN connections, wireless device sends the wireless signal coverage to meet

the extended family and small and medium wireless access.

Here we introduce the TL-WR703N wireless AP mode configuration.

TL-WR703NSetting:

Step 1: Connect to TL-WR703N. As the TL-WR703N in AP mode, the default DHCP server is not open, the computer can not

automatically assign IP addresses, so you need to configure the wireless network to connect the computer's IP address in order

to visit the router management interface. Computer wireless network connection IP address is set to 192.168.1.X (1 X 252),

subnet mask: 255.255.255.0, as shown below. After setup is complete, click "OK" to take effect. TL-WR703N default

management IP address "192.168.1.1".


21 11/4/2012 2:33

8/10/2019 703N

9/21

Note: The computer's IP address configuration can refer to the following link:

http://www.tp-link.com.cn/pages/article-detail.asp?result=school&d=72

Step 2TL-WR703N did not set the default wireless security. Computer through a wired or wireless connection to TL-WR703N

(in xp system to TL-WR703N wireless connection for example), scan the environment in the wireless network, select the

TL-WR703N wireless SSID, and click "Connect" to connect the later, as shown below.

Step 3: In the browser, type "192.168.1.1", enter the login user name and password are admin, open the TL-WR703Nmanagement interface, automatic pop-up "Setup Wizard" (the management interface can also click the menu "Setup Wizard") ,

as shown below.

Step 4: Click "Next" to start setting up mode settings page, select "wireless AP mode" as shown below.


21 11/4/2012 2:33

8/10/2019 703N

10/21

8/10/2019 703N

11/21

Step 8: Restart completed at this time TL-WR703N wireless network already set up wireless security, the computer's wireless

network connection is automatically disconnected, reconnect the TL-WR703N need a wireless network (in this case the SSID to

TP-LINK_531984), the connection process to enter TL-WR703N wireless PSK password (in this case abcdefgh), connected to,

the following figure.

Step 9: After configuration is complete, the IP address of your wireless network connection to re-set to the original configuration

(usually automatically obtain an IP address), click "OK" effect, in order to properly connect to the Internet, as shown below. .


21 11/4/2012 2:33

8/10/2019 703N

12/21

Note: TL-WR703N default management IP address "192.168.1.1", it must be TL-WR703N the LAN IP address set to the wired

LAN devices are not all the same IP address to prevent IP address conflicts (under normal circumstances do not change). In the

menu "network parameters" - "LAN port settings", change IP, click the "Save", the router automatically restart. As shown below.

Thus TL-WR703N AP mode configuration is completed, then the computer search to TL-WR703N issued wireless SSID is

TP-LINK_531984, PSK key is abcdefgh.

TL-WR703N Setup guide FourThe wireless network wireless AP mode

TL-WR703N in wireless applications, has the following three application modes: wireless AP mode, the wireless router mode, 3G

wireless routing model, this paper focuses on the wireless AP mode, an introduction to a variety of applications. Mode and 3G

wireless router wireless router mode, please refer to other relevant documents.

Time during the Setup Wizard, select the wireless AP mode, according to the need to select all in AP mode working application

mode, as shown below:

As the TL-WR703N in AP mode, the default DHCP server is not open, the computer can not automatically assign IP addresses,

so you need to configure the wireless network to connect the computer's IP address in order to visit the router management

interface.

Computer wireless network connection IP address is set to 192.168.1.X (1 X 252), subnet mask: 255.255.255.0, as shown

below. After setup is complete, click "OK" to take effect. TL-WR703N default management IP address "192.168.1.1".


21 11/4/2012 2:33

8/10/2019 703N

13/21

Note: The computer's IP address configuration can refer to the following link:

http://www.tp-link.com.cn/pages/article-detail.asp?result=school&d=72

OneHere we introduce the TL-WR703N wireless AP mode, repeater mode (Repeater) under the application.

TL-WR703Nsetting

Step 1: Click relay mode (Repeater), the display as shown below


21 11/4/2012 2:33

8/10/2019 703N

14/21

Step 2: Fill in the remote AP's ssid, mac address or click the scan, in which the pop-up list to select the front end relay to connect

to the SSID of the router, and enter the front of the router with the same encryption type and key.

Step 3: Click Next, restart the computer to take effect.

TwoHere we introduce the TL-WR703N wireless AP mode, client mode (Client) under the application.

TL-WR703Nsetting

Step 1: Click to select client mode (Client), the pop-up as shown below:


21 11/4/2012 2:33

8/10/2019 703N

15/21

Step 2: Manually enter the front-end router's SSID, or scan the list and click Connect, and select the front-end router with the

same encryption method, enter the correct password. As shown below:

Step 3: Click Next, restart the computer to take effect.


21 11/4/2012 2:33

8/10/2019 703N

16/21

ThreeHere we introduce the TL-WR703N wireless AP mode, Bridge mode (Bridge with AP) under the application.

TL-WR703Nand 11g router wireless bridge configuration1.

Note: TL-WR703N in the choice of bridge mode (Bridge with AP), supports the following encryption types: WEP, no encryption,without modifying the wireless security settings. (For this example select WEP for wireless encryption)

In this case 11g router TL-WR541G +, for example, the network topology is as follows:

The following picture shows the TL-WR541G + user interface, set the wireless parameters to specify the channel 6, open the

bridge feature of the bridge on the side and fill in the TL-WR703N device MAC address, and open the security settings, as

shown below:


21 11/4/2012 2:33

8/10/2019 703N

17/21

Below into the TL-WR703N wireless configuration interface configuration:

Step 1: Go to bridged mode, as shown:


21 11/4/2012 2:33

8/10/2019 703N

18/21

Step 2: Scan the pop-up list and choose to connect to the network SSID, as shown:


21 11/4/2012 2:33

8/10/2019 703N

19/21

Step 3: click Next, you need to reboot the router to take effect.

Note: TL-WR703N default management IP address "192.168.1.1 to prevent IP address conflicts, they should be TL-WR703N the

LAN IP address set to the wired LAN devices are not all the same IP address (in general under no change) can be in the menu

"network parameters" - "LAN port settings", change IP, click the "Save", the router automatically reboot as shown below.


21 11/4/2012 2:33

8/10/2019 703N

20/21

TL-WR703Nand 11n wireless router bridge configuration

In this case the TL-WR740N with TL-WR703N bridge, for example.

In the TL-WR703N and 11n wireless bridge products, only need to open the 11n products on the TL-WR703N WDS function toscan and connect, of course, need to maintain the same channel, encryption type, key.

Step 1: First you need to configure TL-WR703N wireless parameters, for example here is a designated channel, the wireless

security settings, encryption type and key support WEP, WPA-PSK/WPA2-PSK encryption, WEP encryption, for example here is

Step 2: TL-WR740N wireless WDS opens, set the following:

Click scan, in which the pop-up list select TL-WR703N the SSID, and select TL-WR703N the same encryption type and enter

the correct key, as shown:


21 11/4/2012 2:33

8/10/2019 703N

21/21

Click Save, the following window appears, can be completed:

Note: TL-WR703N default management IP address "192.168.1.1 to prevent IP address conflicts, they should be TL-WR703N the

LAN IP address set to the wired LAN devices are not all the same IP address (in general under no change) can be in the menu

"network parameters" - "LAN port settings", change IP, click the "Save", the router automatically reboot as shown below.


703n

Documents