7083 321-00
TRANSCRIPT
7083 321-00
ECBN 62
GBInstallation instructionsfor NoFrost combined refrigerator-freezers Page 12
12
Setting up• Avoidpositioningtheapplianceindirectsunlightornearcookers,radiatorsandsimilarsourcesofheat.
• Theflooronwhichtheappliancestandsshouldbehorizontalandlevel.
• Theventilationgrillesshouldnotbeobstructed.Alwaysensurethatthereisgoodventilationandthattheoutwardflowingairisabletoescape.
• StandardEN378specifies that the room inwhichyou installyourappliancemusthaveavolumeof1m³per8gofR600arefrigerantusedintheappliance,soastoavoidtheformationofinflammablegas/airmixturesintheroomwheretheapplianceis located in theeventofa leak in the refrigerantcircuit.Thequantityofrefrigerantusedinyourapplianceisindicatedonthetypeplateontheinsideoftheappliance.
Appliance dimensions
Appliance venting
Therequiredairflowisdirectedthroughtheplinth.
Itisimportanttousetheprovidedventilationgrillefortheventila-tionopening.
Thisopeningmustnotbecovered.
A=76mmB=2027mmC=910mmD=76mmE=910mmG=1078mmH=943mm
Electrical connectionOnlyoperatetheappliancewithalternating current (AC).Thepermissiblevoltageandfrequencyareindicatedonthetypeplate.Thesocketmustbeproperlyearthedandprotectedbyafuse.Thetrippingcurrentofthefusemustbebetween10Aand16A.Thesocketmustnotbesituatedbehindtheapplianceandmustbeeasilyaccessible.
Donotconnecttheapplianceusinganexten-sioncableorextensionsocket.
Donotusestand-aloneinverters(conversionofdirectcurrent toalternatingcurrent/three-phasecurrent)orenergy-savingplugs.Riskofdamagetotheelectroniccontrolsystem!
GB
13
Installation dimensions
Theicemakerisfittedinthefreezercompartmentofthecombinedrefrigerator-freezer.Itmustbeconnectedtothemainswatersup-plytowork.
The water shut-off valve must be positioned within the areasmarkedingrey.
Thesocketmustbepositionedwithintheareasmarkedingreyorabovetheinstallationrecess.
WARNING! The water shut-off valve must not sit directly above the socket!
The gap between the water shut-off valve and the socket must comply with the regulations of the country in which the appliance is used!
14
Mounting the anti-tipping device
WARNING! The supplied anti-tipping bracket must be installed in all cases. This prevents the appliance from tipping over when the fully loaded door is opened.
Installation:1. Markthecentrelineoftheapplianceonthefloor. Aligntheanti-tippingbracketcentretothecentreline.
CAUTION! Ensure that there are no electric cables or water pipes in the wall section to which the anti-tipping bracket is to be secured. These could be damaged during installation.
2. Securetheanti-tippingbrackettothefloorusingthe3screws(6mmx60mm)includedintheaccessorypack.
Thedistancebetweentheleadingedgeofthebodyoftheunitandtherearedgeoftheanti-tippingbracketis610mm.
Important!When securing the anti-tipping bracket to a concrete floor, use suitable plugs!
If the floor slopes down sideways, the anti-tipping bracket must be fitted horizontally. Lay down spacers in the appropriate positions.
Wall
Connection to the water supply
Safety instructions and warnings•Donotconnecttothewatersupplywhilethecombinedrefrigerator-freezerisconnectedtotheelectricitysupply.
•The connection to the mains water supply may only be made by trained personnel.
•The water quality must comply with the drinking water directives of the country in which the appliance is used.
• The icemaker is designed exclusively tomake ice cubes inquantitiesrequiredbyahouseholdandmayonlybeoperatedwithwatersuitableforthispurpose.
• Allrepairsandworkontheicemakermayonlybecarriedoutbycustomerservicepersonnelorothertrainedpersonnel.
•The manufacturer cannot accept liability for damage caused by a faulty connection to the mains water supply.
Water pressureThewater pressuremustbebetween0.15 and 0.6 MPa (1.5 - 6 bar).
Important:If thewater filter is inserted in theappliance, thewater pressuremustliebetween0.3 and 0.6 MPa (3 - 6 bar).Ifthewaterpressurewiththeinsertedwaterfilteristoolow,thismaycausetheicemakertomalfunction.
Thewatersupplytotheappliancemustbethroughacoldwater pipe that canwithstandthe operating pressure andcomplies with the hygieneregulations. For this, use thestainless steel hose supplied(length3m).
Installation1. Placetheapplianceinfrontoftheinstal-lationrecess.
2. Applycoverstripsonthesidewallsoftheappliance.
GB
15
3. Insertthebentsectionofthehosethroughtheopeningattherearoftheappliance.
4. Connectthehosetothesolenoidvalveatthefrontsideoftheappliance.
5. Routethemainscabletowardsthesocket.6. Routethewaterhosetowardsthewatershut-offvalve.
WARNING! Do not connect the appliance to the power supply until the installation is completed.
CAUTION! Lay the mains cable and the water hose in such a way that they will not be damaged when the appliance is slid into the installation recess.
5. 6.
Anti-tippingbracket
Compressormountingplate
Wall
Appliance
7. Pushtheapplianceslowlyintotherecessuntilthecompressormountingplatetouchestheanti-tippingbracket.
WARNING! To prevent the appliance from tipping forwards, the compres-sor mounting plate must be touching the anti-tipping bracket!
8. Connectthehosetotheshut-offtap. Opentheshut-offtapandcheckthesystemforleakage.
Important!Aftertheicemakerhasbeenswitchedon,thewatersupplysystemmustbebled.See thesectionBleeding the ice maker in theoperatinginstructions.
16
Levelling the appliance
1. Adjust the height of theapplianceatthefrontbytwisting the adjustablefeet 1 (A/F27). Use theopen-endedspannerprovided.
Caution!The front feet of the ap-pliance must be firmly placed on the floor.
2. Adjusttheheightoftheapplianceattherearbyturningtheadjustingbars 2.
Turn the adjusting barsclock-wiseuntilthecompressormount-ingplatetouchestheanti-tippingbracket.
Adjusting the front of the drawerIfrequired,thefrontofthefreezerdrawerscanbeadjusted.Transferthescrewsshownintheillustration(ontheleftandrightsidesofthefreezerdrawer)individuallytothelongslotsbelow.Tightenthescrewsinthefrontofthedraweronceitisintherightposition.
Side view of the freezer drawer pulled out
Fasten the appliance in the recessFastentheapplianceintherecessthroughtheupperandlowerhingesoftherefrigeratordoors.Use2screwsforeachhinge.
screws(4x16mm)
GB
17
Before fitting the door panelsRemovethecover1andunscrewtheattachmentbracket2 from the refrigeratordoors.Theseattachmentbracketswillbemountedontotherefrigeratordoorpanels.
Important!The securing nuts are needed for re-mounting the pre-assembled door panels onto the refrigerator doors.
Unscrewtheattachmentbrackets3fromthefreezerdrawers.Theseattachmentbracketswillbemountedontothefreezerpanels.
Important!The screws are needed for re-mounting the pre-assembled freezer panels onto the freezer drawers.
Panel dimensionsMin.panelthickness=16mmMax.panelthickness=19mm
Maximum panel weightRefrigeratorpanel=12kgFreezerdrawerpanel=10kg
18
Mounting the attachment brackets onto the door panelsMarklinesontherefrigeratordoorpanelsasshowninFig. A.
AlignthedismountedbracketsoftherefrigeratordoorstothelinesontherefrigeratordoorpanelsasshowninFig. A 1.Fasteneachbracketwithanyholewhereverpossibleusingaminimumof6screws4x16mm.
Fastenthebracketsprovidedontothefreezerdrawerpanelsusingthreescrews(4x16mm)foreachbracket(Fig. A2).
Fig. A Fig. A 2
Fig. A 1
Refrigerator door panels
Freezer drawer panel
Freezer drawer panel
Fig. A 2
GB
19
Mounting the refrigerator panelThedescriptionisforonepanelonly.Theprocedureisthesameforbothpanels.
fig. B
fig. C
1. Opentherefrigeratordoorandsuspendtherefrigeratorpanelonthetopadjustingpins(fig. B).
2. Screwsecuringnutsontotheadjustingpinsandslightlytighten(fig. B).
3. Closetherefrigeratordoorandchecktheheightofthepanel.4. Adjusttheheightofthepanelifnecessary.Undothesecuringnutsandusetheadjustingpinstoadjust(fig. C).
Tomakeitpossibletofastentherefrigeratorpanelatthebottomthesoft-stopcylindermustbedismantled.
6. Graspthesoft-stopcylinderandpulldown(Fig. D).Thesoft-stopcylinderretractsinthedetachedstate.
fig. D
7. Transfertheloweredgeoftheattachmentbracketontothepanelusingapencil.(fig. E).Removethepanelfromtherefrigeratordoor.
fig. E
20
fig. G
fig. K
7. Dismantlethelowerattachmentbracketfromtherefrigeratordoor.Alignthebrackettothelinesontherefrigeratordoorpanel.(fig. G).
Fastenthebracketwithanyholewhereverpossibleusingaminimumof6screws4x16mm.
fig. H
8. Opentherefrigeratordoorandsuspendtherefrigeratorpanelonthetopadjustingpins(fig. H).
9. Screwsecuringnutsontotheadjustingpinsandslightlytighten(fig. H).
10. Movethepaneltotheleftuntilitmakescontactwiththecenterrail(fig. I).
11. Tightenthehexnutsfinally.
fig. I
12. Fastentherefrigeratorpanelusingthesamescrewsthatheldthelowerbracketbeforeremoval(fig. K).
13. Extendthesoft-stopcylinderandconnectwiththeballstud(fig. L).
fig. L
14. Clickcoverintoplace(fig. M).
fig. M
GB
21
Mounting the dust filterThesupplieddustfilterpreventsthatdirtentersthemotorcompart-ment,reducingtherefrigerationperformance.Thereforealwaysinstallthedustfilter.1. Pullthebottomfreezerdrawerrightout.2. Removetheprotectivefilmfromthedustfilter.Insertthefilteratthebottom,pressthebuttondownandclickthefilterintoplace.
Mounting the ventilation grilleImportant!To ensure fault-free operation of the appliance, you must install the supplied ventilation grille.
Do not obstruct the ventilation opening or cover it with a panel!
Mounting the freezer panels1. Pulloutthetopfreezerdrawerandscrewonthepre-assembledpanel.Thesamescrewsmustbeusedasthoseusedtoscrewontheattachmentbrackets(3.5x13).
2. Closethefreezerdrawerandcheckthepositionofthepanel.Adjust theheight of thepanel by undoing the left and rightscrews.Tightenthescrews.
3.Pulloutthebottomfreezerdrawerandmountthepanelinthesameway.
4. Forbothdrawers,coverthegapbetweenthedrawerandthepanelwith thecoverstripssupplied.Remove theprotectivefilmfromthetrimandinsertintothegapatthetop.
3.5x13mm