7452998 hydraulics and pneumatics
TRANSCRIPT
-
7/29/2019 7452998 Hydraulics and Pneumatics
1/30
Hydraulics &Pneumatics
TechnologyDMM3623
-
7/29/2019 7452998 Hydraulics and Pneumatics
2/30
What is Fluid
Power ?
Technology that deals with generation, control andtransmission of power, using pressurized fluids
example: brake automobile, launches spacecraft,mines coal, drives machine tools even drills teeth.
Hydraulics when the fluid is liquid
- petroleum oils, synthetic oils and
water. Pneumatics when the fluid is gas
- air (very abundant and can be readilyexhausted into the atmosphere after completing
task)HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
3/30
Hydraulic Basics
Hydraulics is the science of transmitting force and/ormotion through the medium of a confined liquid. In ahydraulic device, power is transmitted by pushing on aconfined liquid. The transfer of energy takes placebecause a quantity of liquid is subject to pressure. Tooperate liquid-powered systems, the operator should havea knowledge of the basic nature of liquids. This chaptercovers the properties of liquids and how they act underdifferent conditions.
Hydraulics
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
4/30
Fluid System
Fluid transportDelivery of a fluid from one location to another toaccomplish some useful purpose.
Fluid powerDesigned specifically to perform work.
Work-accomplished by a pressurized fluid bearing directlyon an operating fluid cylinder or fluid motor.Fluid cylinder-produces a force in linear motion.Fluid motor-produces a torque in rotary motion.
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
5/30
Hydraulic chain saw
Dextrous hand
EXAMPLES
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
6/30
Advantages of using
Hydraulics
1. Very high force despite small components (if
pneumatics, bigger components are needed forhigh force, thus, incur high cost as well aswastage of compressed air)
2. Very slow and linear movements (if
pneumatics, too slow will create jerking on thecylinder)
3. Very exact positioning (stops exactly on apoint). Compared to pneumatics, theres atolerance and if a load is given, it will move a
little.HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
7/30
1. Start-up under heavy loads (Possible to startthe motor & process a job with a load
attached to it. This is because there is oil inthe actuator though the pump is idling).
3. Simplicity, safety, economy
In general, fluid power systems use fewermoving parts than comparable mechanical orelectrical systems. Thus, they are simpler tomaintain and operate. This, in turn,maximizes safety, compactness and
reliability.
Advantages of usingHydraulics
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
8/30
oceanography
-
7/29/2019 7452998 Hydraulics and Pneumatics
9/30
Disadvantages of using
Hydraulics
1. Slow movement of actuators (Pneumatics are faster)
2. Messy (Leakage may occur and if not bothered, thesurrounding area could be messy. However, constantcleaning could avoid messy.)
3. Dangerous!
i. It produces extreme pressure and if theres a
leakage, oil will be forced out. Stopping the flow withbare hand would result in a punctuated wound.
ii. While in process, oil became hot and flammable(though not easily happened). Therefore, it isadvisable to control the temperature by limiting it(turning off the machine if the limit is exceeded).H
YDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
10/30
General Application of
Hydraulics
Mobile Hydraulics Stationary Hydraulics
Using manualhydraulics to control
Crane
Excavator
Back-hoe
Using electro-hydraulics to control
Press machine
Molding machine
Lathe machine
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
11/30
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
excavator
boom
stick
bucket
4 hydraulic cylinders
-
7/29/2019 7452998 Hydraulics and Pneumatics
12/30
Sky tram is unique. It is self-propelled and travels on astationary cable. Because the tram moves instead of the
cable, the operator can stop, start, and reverse any one carcompletely independently of any other car in the tram system.Integral to the design of the Sky-tram drive is a pump (drivenby a standard eight-cylinder gasoline engine) which suppliespressurized fluid to four hydraulic motors.
Sky-tram
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
13/30
forklift
Tilt Cylinders - are hydraulic cylinders that are mounted to the truck frame and themast. The tilt cylinders pivot the mast to assist in engaging a load.
The Mast - is the vertical assembly that does the work of raising and lowering the load.
It is made up of interlocking rails that also provide lateral stability. The interlocking rails
may either have rollers or bushings as guides. The mast is either hydraulically operated
by one or more hydraulic cylinders or it may be chain operated with a hydraulic motor
providing motive power. It may be mounted to the front axle or the frame of the forklift.HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
14/30
Pressure Transfer Medium
Form of liquid used
Oil, when surrounding is not hot (car brake system)
5. Water, when surrounding is hot / very hot. To
avoid corrosion and to have better lubrication,water is usually mixed with some additives (foodprocessing, semiconductor process, papermanufacturing, construction works, medical andwelfare appliances).
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
15/30
Pressure Transfer Medium
Vs.Gas Liquid
Compressible, both intheory and practical
Pressure is storable
Not compressible intheory, however, iscompressible up to0.7% in practical (dueto small quantity of
air in the liquid)
Pressure is notstorable. Releasedwhen the pump stops.
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
16/30
Common Fluid in Hydraulic System
Base stock may be either castor oil, glycol, ester,ethers, mineral oil, chutte etc.
Some of the trade names for hydraulics fluidsinclude:
DuradFyrquel
Houghton-Safe
lubritherinHYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
17/30
A hydraulic fluid has the following 4 primary functions:-2. Transmit power3. Lubricate moving parts
4. Seal clearance between mating parts5. Dissipate heat
In addition a hydraulic fluid must be inexpensive and readilyavailable. A hydraulic fluid should have the followingproperties:-
2. Good lubricity3. Ideal viscosity4. Chemical stability5. Fire resistance6. Low density7. Foam resistance
8. Nontoxicity9. Low volatilit
Fluid Selection
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
18/30
Fluids: Liquids and Gases
Liquids refer to both gases and liquids.
- is a fluid that, for a given mass, will have adefinite volume independent of the shape of itscontainer.
- A free surface is also formed in the case of abody of water, such as a lake.Gases fluids that are readily compressible. In addition,
their volume will vary to fill the vessel containing them.- the gas molecules always fill the entire vessel.
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
19/30
Parameter Liquid Gas
Volume Has its own volume Volume is determinedby container
Shape Takes shape of container Expands to completely
but only to its volume fill and take the shapeof the container
Compressibility Incompressible for most Readily compressibengineering applications
Physical differences between liquids and gases
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
20/30
Key
Equation
Specific weight
Density
Kinematic viscosity
V
W=
V
m=
=
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
21/30
Pressure is force exerted against a specific area (force per unit
area) expressed in pounds per square inch (psi). Pressure cancause an expansion, or resistance to compression, of a fluid thatis being squeezed. A fluid is any liquid or gas (vapor). Force isanything that tends to produce or modify (push or pull) motionand is expressed in pounds.
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
Pressure
-
7/29/2019 7452998 Hydraulics and Pneumatics
22/30
The earth has an atmosphere of air extending 50 milesup, and this air has weight. This air creates a head ofpressure that is called atmospheric pressure. A column ofair 1 square inch in cross section and the height of theatmosphere would weigh 14.7 pounds at sea level. Thus,the earth's atmospheric pressure is 14.7 psi at sea level.The role of atmospheric pressure in most hydraulic
systems is significant.
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
Continue
-
7/29/2019 7452998 Hydraulics and Pneumatics
23/30
Force
Example of P at 100 kPa and A at 20 m,
F = P x A, so F = 100 kPa x 20 m
F = 2000 kN.
Pressure is defined as force per unit area.Hence, pressure is the amount of force acting
over a unit area, as indicated by
Pressure (P) = Force (F) / Area(A)
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
24/30
Example
A lifting is to lift a load of 15kN and is to havea system pressure of 75 bar. How large does
the piston surface need to be?
Solution:
P = F/A
A = F/P= 15000N/(75x105 Pa)
= 0.002 m2
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
25/30
EXAMPLE
F2=10 kN
d2=3 m
d1=0.5 m
S2=0.5m
F1 = ?
S1 = ?
S1
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
26/30
Answer
F1/A1 = F2/A2
A1 = 0.1963 m2
(1 mark)A2 = 7.0686 m
2 (1 mark)
F1 = (F2/A2) x A1
= (10 kN / 7.0686 m2) x 0.1963 m2
= 0.278 kN (3 marks)
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
27/30
Answer
W = F.s
F1s1 = F2s2
0.278 xs1 = 10 x 0.5
s1 = 17.986 m (5 marks)
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
28/30
Sky-tram
backhoe
HYDRAULICS
&P
NEUMAT
ICS
DMM3623
Prepared by Zulkifli b Ahmad @ Manap
-
7/29/2019 7452998 Hydraulics and Pneumatics
29/30
FlowFlow is the movement of a hydraulic fluid caused by a differencein the pressure at two points. In a hydraulic system, flow isusually produced by the action of a hydraulic pump-a deviceused to continuously push on a hydraulic fluid. The two ways ofmeasuring flow are velocity and flow rate.
a. Velocity. Velocity is the average speed at which afluid's particles move past a given point,
measured in feet per second (fps). Velocity is animportant consideration in sizing the hydraulic lines thatcarry a fluid between the components.
b. Flow Rate. Flow rate is the measure of how muchvolume of a liquid passes a point in a given time. Flow ratedetermines the speed at which a load moves and, therefore,
is important when considering power.
Pressure. An example of pressure is the air (gas) that fills anautomobile tire. As a tire is inflated, more air is squeezed into itthan it can hold. The air inside a tire resists the squeezing bypushing outward on the casing of the tire. The outward push of the
air is pressure. Equal pressure throughout a confined area is acharacteristic of any pressurized fluid. For example, in an inflatedtire, the outward push of the air is uniform throughout. If it werenot, a tire would be pushed into odd shapes because of itselasticity.
-
7/29/2019 7452998 Hydraulics and Pneumatics
30/30
Energy is the ability to do work. The three forms of energy arepotential, kinetic, and heat. Work measures accomplishments; itrequires motion to make a force do work. Power is the rate of
doing work or the rate of energy transfer.
a. Potential Energy. Potential energy is energy due to position.An object has potential energy in proportion to its verticaldistance above the earth's surface. For example, water held backby a dam represents potential energy because until it is released,the water does not work. In hydraulics, potential energy is astatic factor. When force is applied to a confined liquid, as shown
in Figure 1-4, potential energy is present because of the staticpressure of the liquid. Potential energy of a moving liquid can bereduced by the heat energy released. Potential energy can alsobe reduced in a moving liquid when it transforms into kineticenergy. A moving liquid can, therefore, perform work as a resultof its static pressure and its momentum.