8100 mobile device test system...intrig data monitor airaccess c2k 4.82.001 c2k network emulation...

8100 Mobile Device Test System Location Test System Q750 Platform Version 4.1 System Deployment Instructions

8100 MDTS Location Test System Q750 Platform Version 4.1 – System Deployment Instructions

www.spirent.com 2

© 2020 Spirent Communications, Inc. All Rights Reserved.

All of the company names and/or brand names and/or product names referred to in this document, in particular, the name “Spirent” and its logo device, are either registered trademarks or trademarks of Spirent plc and its subsidiaries, pending registration in accordance with relevant national laws. All other registered trademarks or trademarks are the property of their respective owners. The information contained in this document is subject to change without notice and does not represent a commitment on the part of Spirent Communications. The information in this document is believed to be accurate and reliable; however, Spirent Communications assumes no responsibility or liability for any errors or inaccuracies that may appear in the document.

Page Part Number: 71-008873, Version A0


www.spirent.com 3

Table of Contents 1. Introduction ........................................................................................ 5

1.1. Overview .................................................................................................... 5

1.2. How to Contact Us ..................................................................................... 7

2. System Upgrade Instructions ............................................................. 8

2.1. Overview .................................................................................................... 8

2.2. Prerequisites .............................................................................................. 8

2.3. Download and Unzip the Software Update ................................................ 9

2.4. Install the LTS Q750 4.1 Software Personality ........................................ 11

2.5. Activate the LTS Q750 4.1 Software Personality ..................................... 13

2.6. Configure Controller PC1 ......................................................................... 13

2.6.1. Configure the Controller PC1 Network Settings ............................ 13

2.6.2. Configure the Local Area Connection for Controller PC1 .............. 14

2.6.3. Select the vmsync Data File .......................................................... 16

2.7. Configure the Application Server ............................................................. 18

2.7.1. Configure the Network Settings for the Application Server ........... 18

2.7.2. Configure the Local Area Connection on the Application Server ........................................................................................... 20

2.7.3. Select the vmsync Data File .......................................................... 21

2.7.4. Import the ProLab License ............................................................ 23

2.8. Reactivate the Software Personality ........................................................ 26

2.9. Configure LTS Software Applications on Controller PC1 ......................... 27

2.9.1. Configure SimGEN/Positioning on Controller PC1 ........................ 27

2.9.2. Configure SimCHAN on Controller PC1 ........................................ 32

2.10. Configure TTworkbench Express ............................................................. 33

2.11. Update Microsoft Security Essentials ...................................................... 37

2.11.1. Update Microsoft Security Essentials on Controller PC1 ........... 37

2.11.2. Update Microsoft Security Essentials on the Application Server ........................................................................................ 41

2.12. Upgrade the WTS122-CA ........................................................................ 44

2.12.1. Install WTS122-CA Software Version 2.10.04 ........................... 44

2.12.2. Verify Your Installation ............................................................... 47

2.12.3. Update Microsoft Security Essentials ........................................ 50


www.spirent.com 4

2.13. Install the Test Suites............................................................................... 56

2.14. Upgrade GSS7000 .................................................................................. 56

3. Windows and Simple DNS Activation .............................................. 63

3.1. Overview .................................................................................................. 63

3.2. Step 1: Activate Windows via a Phone .................................................... 63

3.3. Step 2: Activate Simple DNS ................................................................... 71

4. Software License Agreement ........................................................... 75


www.spirent.com 5

1. Introduction

1.1. Overview This document provides the instructions for upgrading the 8100 Mobile Device Test System Location Test System (LTS) Q750 platform from version 4.0 to version 4.1. 8100 Mobile Device Test System LTS Q750 platform version 4.1 consists of the software components listed in the following table.

Software Version Description Spirent TestDrive LTS 4.1.104 Test Executive software (includes

SUPL 1.0 ETS, TS 34.171 MP, TS 51.010 MP, and Spirent Performance test cases)

Spirent SMLC Emulator 4.1.104 SMLC Emulation software AirAccess WCDMA-HS 2.05.001 WCDMA Network Emulation

software SimCHAN 3.03.02.11 SimCHAN software Positioning Application (GSS6700) 6.05.008 GPS Simulation software for

GSS6700 Positioning Application (GSS7000) 6.05.008 GPS Simulation software for

GSS7000 TTworkbench Spirent Express 1.27.2 TTworkbenchExpress software Development Library Services 9.00.036 Development Library Services SPARC - Server 1.3.4 CS8 Interactive Tester software 2.30.018 LTE Network Emulation software Intrig Data Monitor 1.3.5 Intrig Data Monitor AirAccess C2K 4.82.001 C2K Network Emulation software Universal DM V2 4.7.1 Universal DM UE AT Interface 1.5.60 UE AT Interface Spirent LTS Test Pack SUPL ENH 1.72.012 SUPL Enhanced Test Pack Spirent LTS Test Pack TS34.172 and TS51.010 SC (conformance)

1.74.123 TS51.010 SC Test Pack

Spirent LTS Test Pack GNSS Performance Tests

1.75.033 GNSS Performance Test Pack

Spirent LTS OMA_SUPL_V2_ATS OMA Scripts Tests

2.12.16 OMA SUPL 2.0 Tests

TS37.571-1 Section 7 A-GNSS 1.75.060 TS37.571-1 A-GNSS Tests 37.571-2 Section 7 - LPP Protocol Conformance

5.0.15 37.571-2 Sec 7 - LPP Protocol Conformance Test Pack


www.spirent.com 6

Software Version Description TS SUPL2 A-GLONASS Performance Tests

1.3.5 TS SUPL2 A-GLONASS Performance Tests

Spirent LTS OTA Test Pack 2.75.025 CTIA OTA Test Pack Spirent LTS OTA Service 1.11.023 Software component for serving

OTA applications Spirent AT Control 1.5.25 AT Command Driver UESimulator 12.2.002 UE Simulator AirAccessHS Debugger 2.2.1 AirAccessHS Debug Spirent UTS Control 2.2.1 UTS Control Service Spirent WCE-IAPI 3.51.034 WCE-IAPI SR5500 TestKit 3.51.002 SR5500 Driver Message Logging Installation 1.1.0 HTML Message Logging Spirent Data Client 1.16.250 Spirent Data Client Spirent IMS Client 3.1.0008 Spirent IMS Client Spirent IMS Client Codec Library 1.0.0 Spirent IMS Client Codec Library Spirent WTS122-CA 2.10.04 Software running on the

WTS122-CA PosApp Launcher 1.0.1 GSS7000 PosApp Launcher


www.spirent.com 7

1.2. How to Contact Us To obtain technical support for any Spirent Communications product, please contact our Support Services department using any of the following methods: Americas E-mail: [email protected] Web: http://support.spirent.com Toll Free: +1 800-SPIRENT (+1 800-774-7368) (North America) Hours: Monday through Friday, 05:30 to 18:00 Pacific Time Europe, Africa, Middle East E-mail: [email protected] Web: http://support.spirent.com EMEA Phone: +33 (1) 6137 2270 UK Phone: +44 1803 546333 Toll Free Phone: +1 818-676-2616 Hours: Monday through Thursday, 09:00 to 18:00, 9:00 to 17:00 Friday, Paris Time Asia Pacific E-mail: [email protected] Web: http://support.spirent.com In China Mainland Phone: +86 (400) 810-9529 (toll-free) Out of China Mainland Phone: +86 (10) 8233 0033 India Phone: 1800-419-2111 Operating Hours: Monday through Friday, 09:00 to 18:00 Beijing Time The Spirent Knowledge Base (http://support.spirent.com) is designed to serve your technical information needs. The Knowledge Base gives you access to tens of thousands of documents that help answer your network analysis and measurement questions. New content is added daily by Spirent’s communications and networking experts. Sign in with your user ID and password to gain access to additional content that is available only to customers – user manuals, Help files, release notes, Tech Bulletins, and more. When you sign in, you can also use the Knowledge Base to download software and firmware, and to manage your SRs. Information about Spirent Communications and its products and services can be found on the main company website at http://www.spirent.com. Company Address Spirent Communications, Inc. 26750 Agoura Road Calabasas, CA 91302 USA


www.spirent.com 8

2. System Upgrade Instructions

2.1. Overview The following sections contain the steps necessary to install LTS Q750 platform version 4.1 and the necessary supporting software components on an existing system. These steps include: 1. Download and unzip the software update package from the Spirent Customer Service

Center website. 2. Install the LTS Q750 version 4.1 software personality. 3. Activate the LTS Q750 version 4.1 software personality. 4. Configure Controller PC1. 5. Configure the Application Server. 6. Reactivate the personality. 7. Configure the LTS software applications on Controller PC1. 8. Configure TTworkbench Express. 9. Update Microsoft Security Essentials. 10. Upgrade the WTS122-CA. 11. Install the test suites. 12. Upgrade the GSS7000.

2.2. Prerequisites Before upgrading the system, make sure:

• You have a 100GB external USB drive to which you will download and unzip the software update from the Spirent Customer Service Center website.

• LTS Q750 version 4.0 is installed. • You have a copy of the ProLab license. Make sure the ProLab license is on the external

USB drive. • You have a new license file for TTworkbench Express 27.


www.spirent.com 9

2.3. Download and Unzip the Software Update In this section, you will download and unzip the LTS Q750 Platform version 4.1 software update and Spirent WTS122-CA software version 2.10.04 for the WTS122-CA from the Spirent Customer Service Center to a 100GB external USB drive. The version 4.1 software update is a zipped file that consists of the following files:

• 8100_SW_LTS_QSeries_4.1.0-10.tar file • 8100 MDTS Q750 v4.1.0 Windows Installer

NOTE: We recommend that you extract the zipped package file to a portable 100GB USB device. These files are needed to update multiple computers on the system.

Also, you will need a zip application (for example, 7-Zip) to unzip the zipped package file you download from the Spirent CSC.

Before performing this procedure, make sure you have an external 100GB USB drive. Perform the following steps to download and unzip the software update: 1. Connect the external USB drive to your PC. 2. Log into the Spirent Customer Service Center website at http://support.spirent.com using

the e-mail address and password assigned to you by Spirent. 3. On the Customer Service Center page, click the Downloads tab.

The Spirent Downloads page appears. 4. From the Release Type box, select Controlled Release. 5. From the Product Line box, select 8100 Platforms. 6. In the Categories area, check the Q750 check box. 7. Download the following software: LTS Q750 SC10 Installer, Controlled Release, v4.1.0 for VM Image part 1 of 2 LTS Q750 SC10 Installer, Controlled Release, v4.1.0 for VM Image part 2 of 2

8. After the zipped files are downloaded, open Windows Explorer and go to the folder contains the downloaded files. a. Right-click on the file 30-013446.vA5-0.zip.001.

A menu appears. b. Select 7-Zip > Extract files.

The Extract dialog box appears. c. Uncheck the check box located below the Extract to box. d. Select the external USB drive, and click the OK button.

The selected files are extracted and combined on the external USB drive.


www.spirent.com 10

9. After the files are extracted, perform the following steps to download WTS122-CA software version 2.10.04: a. On the Downloads page, select General Release from the Release Type box. b. From the Product Line box, select 8100 Platforms. c. In the Categories area, check the WTS check box. d. Download the following software to the external USB drive:

• WTS122-CA, v2.10.04 for VM Image File 1 of 2 • WTS122-CA, v2.10.04 for VM Image File 2 of 2

e. After the zipped files are downloaded, open Windows Explorer and go to the folder on the external USB drive that contains the downloaded files.

f. Right-click on the file WTS_SW_WTS122CA_2.00.00_to_2.10.04-23.zip.001. A menu appears.

g. Select 7-Zip > Extract files. The Extract dialog box appears.

h. Click the OK button. The selected files are extracted and combined into a single tar file.

10. Disconnect the external USB drive from your PC. 11. Connect the external USB drive to an available USB 2.0 port in the left column of USB 2.0

ports on the SC10.

NOTE: The SC10 has two columns of USB 2.0 ports located to the right of the monitor ports. The left column of USB ports is assigned to Controller PC1. The right column of USB ports is assigned to Controller PC2.

12. Go to the next section to install the LTS Q750 4.1 software personality.


www.spirent.com 11

2.4. Install the LTS Q750 4.1 Software Personality Perform the following steps: 1. Make sure the external USB drive containing the software update is connected to an

available USB 2.0 port in the left column of USB 2.0 ports on the SC10. 2. From the QEMU menu at the top, left corner of the VM window, select 8100 Services

Management Utility - Chromium. The 8100 Services Management Utility appears.

3. In the 8100 Services Management Utility, click the Software Personalities button. The Software Personalities page appears.

4. In the Action column, click the Deactivate button. A dialog box appears prompting you to confirm your action.

5. Click the OK button. When the action is complete, the message Operation Complete appears.

6. Click the Return to Software Personalities button. The Software Personalities page appears.

7. Click the Software Installation button. The Software Installation page appears.

8. In the Software Channel area, click the Add Local Channel (USB) button. The Input Required dialog box appears.

9. Click the Choose File button. The Open File dialog box appears.

10. Click the media button. 11. Double-click on the external USB drive that contains the file 8100_SW_LTS_QSeries_4.1.0-

10.tar. The external USB drive will typically be displayed as sdc1 or sdd1 depending on what other items are currently installed on the USB drive.

12. Select the file 8100_SW_LTS_QSeries_4.1.0-10.tar, and then click the Open button. A dialog box appears and displays the message that it is searching for removable media for 8100 software. When the software is found, the message Channel Added Successfully appears.

13. Click the Close Results Window button. The Software Installation page appears. The table in the Software Channel area displays 8100Local1. This is the .tar file you just loaded.

14. In the Software Channel area, click the Enable button for 8100Local1. The Operation in Progress status box appears. After the operation is complete, the message Channel Enabled appears.


www.spirent.com 12

15. Click the Close Results Windows button. Y appears in the Enabled column for 8100Local1, and the software component from the .tar file for 8100Local1 appears in the table in the Software Releases Available area. The Install button appears next to 8100-LTS-QSeries_Release_4.1.0.

16. If the message In order to proceed with a release install, the Instrument Management Utility must be updated appears in the Software Releases Available area, perform the following steps: a. Click the Upgrade button.

A confirmation dialog box appears. b. Click the OK button to upgrade the 8100 Services Management Utility.

A dialog box displays the message This webpage is not available. c. Click the Reload button in the dialog box.

After the 8100 Services Management Utility is upgraded, the Software Personalities page appears.

d. Click the Software Installation button. The Software Installation page appears.

17. In the Software Releases Available area, click the Install button for 8100 LTS QSeries Version 4.1.0. A dialog box appears prompting you to confirm that you want to install the selected software package.

18. Click the OK button. The Operation in Progress status box appears showing the status of the installation. The software installation process may take up to 30 minutes.

WARNING: Do not refresh the browser or power down the SC10 during the installation process.

After the software personality is installed, the SC10 reboots automatically, and the Software Personalities page appears.

19. Go to the next section to activate the LTS Q750 4.1 software personality.


www.spirent.com 13

2.5. Activate the LTS Q750 4.1 Software Personality This section describes how to activate the LTS Q750 4.1 software personality. Perform the following steps: 1. In the 8100 Services Management Utility, click the Software Personalities button.

The Software Personalities page appears. 2. Click the Activate button for 8100 LTS QSeries Version 4.1.0 in the Action column of the

table. A dialog box appears prompting you to confirm your action.

3. Click the OK button. After the LTS Q750 4.1 personality activates successfully, the Controller PC1 password window appears.

4. Go to the next section to configure Controller PC1.

2.6. Configure Controller PC1 In this section, you will perform the following steps to configure the Controller PC1: 1. Configure the network settings. 2. Configure the local area connection. 3. Select the vmsync data file.

2.6.1. Configure the Controller PC1 Network Settings Perform the following steps: 1. In the Controller PC1 password window, enter Sp!rent and press the ENTER key. 2. If the Windows Activation dialog box appears, perform the following steps:

a. Click the Ask me later button. The Windows Activation message box appears stating that importance of using genuine Microsoft software.

b. Click the OK button. 3. If a message box appears stating that you may be a victim of counterfeiting, click the Close

button. 4. If the Simple DNS Plus Licensing dialog box appears, ignore it.


www.spirent.com 14

5. If a Microsoft Windows dialog box appears prompting you to restart your computer to apply these changes, click the Restart Later button. The VMSync dialog box appears, prompting you to select the vmsync.data file.

NOTE: Ignore the VMSync dialog box for now. You will configure VMSync later in this section.

6. In the Set Network Location dialog box, uncheck the Treat all future networks that I connect to as public, and don’t ask me again check box.

7. Click on Home network. After approximately one minute, the Create a Homegroup dialog box appears.

8. In the Create a Homegroup dialog box, click the Cancel button. 9. Go to the next section to configure the Controller PC1 local area connection.

2.6.2. Configure the Local Area Connection for Controller PC1 Perform the following steps: 1. On the Controller PC desktop, select Start > Control Panel.

The All Control Panel Items window appears. 2. Click on Network and Sharing Center.

The Network and Sharing Center window appears. 3. Click on Change adapter settings.

The Network Connections window appears. 4. Double-click on Local Area Connection 2.

The Local Area Connection 2 Status dialog box appears. 5. Click the Properties button.

The Local Area Connection 2 Properties dialog box appears.


www.spirent.com 15

6. Double-click on Internet Protocol Version 4 (TCP/IPv4). The Internet Protocol Version 4 (TCP/IPv4) Properties dialog box appears.

Figure 1. Internet Protocol Version 4 (TCP/IPv4) Properties dialog box.

7. Make sure the IP address is set to 192.168.0.65. 8. Make sure Default gateway is set to 192.168.0.1. 9. In the Preferred DNS server box, enter the IP address of the customer’s DNS server. 10. In the Alternate DNS server box, enter 8.8.8.8. 11. Click the OK button. 12. Click the OK button in the Local Area Connection 2 Properties dialog box. 13. Click the Close button in the Local Area Connection 2 Status dialog box. 14. Close the Network Connections window. 15. On the desktop, click Start. 16. In the text box, type cmd and press the ENTER key.

The Administrator: C:\Windows\system32\cmd.exe window appears. 17. At the command prompt, type ping 192.168.0.1 and press the ENTER key. 18. Make sure you can ping this address. 19. Close the cmd.exe window. 20. Go to the next section to select the vmsync data file.


www.spirent.com 16

2.6.3. Select the vmsync Data File Perform the following steps: 1. Access the VMSync dialog box, which is displayed on the desktop of the Controller PC1.

Figure 2. VMSync message box.

2. Click the OK button. The Open dialog box appears.

3. Go to the folder D:\VMSync\8100-LTS-QSeries_4.0, and select the file vmsync.data.


www.spirent.com 17

4. Click the Open button. The VMSync Tool accesses the license and password information from the previous release and registers your various licenses. For the license registration to succeed, the system must have an internet connection. If there is a problem with the internet connection, the following Internet Connection Test dialog box appears.

Figure 3. Internet Connection Test dialog box.

5. Perform one of the following steps: If the Internet Connection Test dialog box does NOT appear, go to the next section to

configure the Application Server. If the Internet Connection Test dialog box appears, perform the following steps:

a. Click the Yes button to retry the connection test. If the system does not have an internet connection, the Internet Connection Test dialog box appear again.

b. If the Internet Connection Test dialog box appears again, click the No button. The following Windows Activation message box appears.

Figure 4. Windows Activation message box.

c. Click the OK button and then go to Chapter 3 to activate Windows and Simple DNS. After you activate Windows and Simple DNS, go to the next section to configure the Application Server.


www.spirent.com 18

2.7. Configure the Application Server In this section, you will perform the following steps to configure the Application Server: 1. Configure the network settings. 2. Configure the local area network connection. 3. Select the vmsync data file 4. Import the ProLab license.

2.7.1. Configure the Network Settings for the Application Server Perform the following steps: 1. Click the QEMU menu at the top, left corner of the Chromium window, and select QEMU

(ApplicationServer). The Application Server desktop appears.

2. If the Windows Activation dialog box appears on the Application Server, perform the following steps: a. Click the Ask me later button.

The Windows Activation message box appears stating that importance of using genuine Microsoft software.

b. Click the OK button. 3. If a message box appears stating that you may be a victim of counterfeiting, click the Close

button. 4. If a Microsoft Windows dialog box appears prompting you to restart your computer to apply

these changes, click the Restart Later button. The VMSync dialog box appears, prompting you to select the vmsync.data file.

NOTE: Ignore the VMSync dialog box for now. You will configure VMSync later in this section.

5. On the Application Server, select Start > Control Panel. The All Control Panel Items window appears.

6. Click on Network and Sharing Center. The Network and Sharing Center window appears.


www.spirent.com 19

7. Click on the Network Location. This will be either Home, Work, or Public as shown in the following figure. The Set Network Location dialog box appears.

Figure 5. Application Server Network Location Settings.

8. In the Set Network Location dialog box, uncheck the Treat all future networks that I connect to as public, and don’t ask me again check box.

9. Click on Home network. 10. After the network location settings are configured (which usually takes approximately one

minute), click the Close button. 11. Go to the next section to configure the local area connection on the Application Server.


www.spirent.com 20

2.7.2. Configure the Local Area Connection on the Application Server Perform the following steps: 1. In the Network and Sharing Center window, click on Change adapter settings.

The Network Connections window appears. 2. Double-click on LAC_SDC.

The LAC_SDC Status dialog box appears. 3. Click the Properties button.

The LAC_SDC Properties dialog box appears. 4. Double-click on Internet Protocol Version 4 (TCP/IPv4).

The Internet Protocol Version 4 (TCP/IPv4) Properties dialog box appears. 5. Make sure IP address is set to 192.168.0.70. 6. Make sure Default gateway is set to 192.168.0.1. 7. In the Preferred DNS server box, enter the IP address of the customer’s DNS server. 8. In the Alternate DNS server box, enter 8.8.8.8. 9. Click the OK button. 10. Click the OK button in the LAC_SDC Properties dialog box. 11. Click the Close button in the LAC_SDC Status dialog box. 12. Close the Network Connections window. 13. On the desktop, click Start.

The Start menu appears. 14. In the text box, enter cmd and press the ENTER key.

The Administrator: C:\Windows\system32\cmd.exe window appears. 15. At the command prompt, enter ping 192.168.0.1 and press the ENTER key. 16. Make sure you can ping this address. 17. Close the cmd.exe window. 18. Go to the next section to select the vmsync data file.


www.spirent.com 21

2.7.3. Select the vmsync Data File Perform the following steps: 1. Access the VMSync dialog box, which is displayed on the desktop of the Application Server.

Figure 6. VMSync message box.

2. Click the OK button. The Open dialog box appears.

3. Go to the folder D:\VMsync\8100-LTS-QSeries_4.0, and select the file vmsync.data.


www.spirent.com 22

4. Click the Open button. The VMSync Tool accesses the license and password information from the previous release and registers your various licenses. For the license registration to succeed, the system must have an internet connection. If there is a problem with the internet connection, the following Internet Connection Test dialog box appears.


5. Perform one of the following steps: If the Internet Connection Test dialog box does NOT appear, go to the next section to

import the ProLab license. If the Internet Connection Test dialog box appears, perform the following steps:

a. Click the Yes button to retry the connection test. If the system does not have an internet connection, the Internet Connection Test dialog box appears again.

b. If the Internet Connection Test dialog box appears again, click the No button. The following Windows Activation message box appears.


c. Click the OK button, and then go to Chapter 3 to activate Windows via a phone. After you activate Windows, go to the next section to import the ProLab license.


www.spirent.com 23

2.7.4. Import the ProLab License In this procedure, you will move the ProLab license file from the external USB drive to the Application Server and then import the license file into ProLab.

NOTE: Before performing this procedure, make sure you have the ProLab license for this SC10.

Perform the following steps: 1. Connect the USB drive containing the ProLab license file to an available USB port on the

left column of USB ports on the SC10. The left column of USB ports is assigned to Controller PC1.

2. Click the QEMU menu at the top, left corner of the Chromium window, and select QEMU (Controller PC1). The Controller PC1 desktop appears.

3. On the Controller PC1 desktop, select Start > All Programs > Accessories > Remote Desktop Connection. The Remote Desktop Connection window appears.

4. In the Computer box, enter the IP address of the Application Server (192.168.0.70). 5. Click the Options button.

The User name box and tabs appear in the Remote Desktop Connection window. 6. In the User name box, type spirent. 7. Click the Local Resources tab.

The Local Resources tab appears. 8. In the Local devices and resources area, click the More button.

The Local devices and resources dialog box appears. 9. In the Local devices and resources dialog box, select (check) the Drives check box, and

then click the OK button. 10. In the Remote Desktop Connection window, click the Connect button. 11. If a Remote Desktop Connection dialog box appears asking if you trust this remote

connection, click the Connect button. The Windows Security dialog box appears.

12. In the Password box, type Sp!rent and click the OK button. 13. If a Remote Desktop Connection dialog box appears stating that the identity of the remote

computer cannot be verified, click the Yes button. The Application Server desktop appears.

14. Using Windows Explorer, move the ProLab license file (.lic) from the USB drive (D on SPIRENT-WIN7) to a folder on the D: drive of the Application Server.

15. Close Windows Explorer.


www.spirent.com 24

16. On the Application Server desktop, double-click on the ProLab Manager icon. The Register your ProLab dialog box appears.

Figure 9. Sample Register your ProLab dialog box.


www.spirent.com 25

17. In the Register your ProLab dialog box, click . The Open dialog box appears.

18. In the Open dialog box, select the license file that you copied to the D: drive of the Application Server, and then click the Open button. The license file name is displayed in the corresponding text box.

19. Click the Register button. If the registration is successful, the message Valid License appears in the ProLab Registration Status area at the top of the Register your ProLab dialog box.

20. Click the OK button. The ProLab Manager window appears.

21. Close the ProLab Manager window. 22. Select Start > Log off to end the Remote Desktop Session to the Application Server.

The Controller PC1 desktop appears. 23. On the Controller PC1 desktop, click Start and then click the Shut down button.

After the VM shuts down, the Application Server desktop appears. 24. If the password screen appears, type Sp!rent and press the ENTER key. 25. Go to the next section to reactivate the software personality.


www.spirent.com 26

2.8. Reactivate the Software Personality Perform the following steps: 1. From the QEMU menu at the top, left corner of the VM window, select 8100 Services

Management Utility - Chromium. The 8100 Services Management Utility appears.

2. In the 8100 Services Management Utility, click the Software Personalities button. The Software Personalities page appears.

3. In the Action column, click the Reactivate button. A dialog box appears prompting you to confirm your action.

4. Click the OK button. After the personality activates successfully, the 8100 Services Management Utility window closes, and the Controller PC1 password window appears.

5. Go to the next section to configure the LTS software applications on Controller PC1.


www.spirent.com 27

2.9. Configure LTS Software Applications on Controller PC1

In this section, you will perform the following procedures on Controller PC1: 1. Configure SimGEN/Positioning. 2. Configure SimCHAN.

2.9.1. Configure SimGEN/Positioning on Controller PC1 NOTE: Skip this procedure if the system contains a GSS7000.

Perform the following steps: 1. In the Controller PC1 password window, enter Sp!rent and press the ENTER key.

The Controller PC1 desktop appears. 2. On the Controller PC1, select Start > All Programs > Positioning Application >

Positioning Application. 3. If the PosApp Registry to User Settings dialog box appears, click the Close button.

Figure 10. PosApp Registry to User Settings dialog box.


www.spirent.com 28

4. If the following PosApp message boxes appear, click the OK button.

Figure 11. PosApp message boxes.


www.spirent.com 29

The License agreement dialog box appears.

Figure 12. License Agreement dialog box.


www.spirent.com 30

5. Read the license agreement, and click the Accept button if you agree to the terms of the license agreement.

6. In the Open dialog box, select the default scenario as shown in the following figure.

Figure 13. Open dialog box for Default Scenario.


www.spirent.com 31

7. In the Open dialog box, click the Open button. The following SimGEN dialog box appears.

Figure 14. SimGEN dialog box.

8. Click the No button. 9. Select Options > Message reported and check the Disable message popups check box. 10. When finished, click the OK button. 11. Close the SimGEN window 12. Go to the next section to configure SimCHAN on Controller PC1.


www.spirent.com 32

2.9.2. Configure SimCHAN on Controller PC1 Use this procedure to configure SimCHAN.

NOTE: Skip this procedure if the system contains a GSS7000.

Perform the following steps: 1. On Controller PC1, select Start > All Programs > SimCHAN > SimCHAN.

The SimCHAN window appears. 2. If the Open File – Security Warning window appears, uncheck the Always ask before

opening this file check box, and click the Run button. 3. In the SimCHAN window, select Help>About 4. Verify that the correct version of SimCHAN is installed. 5. When finished, close the window. 6. Close the SimCHAN window. 7. Go to the next section to configure TTworkbench Express.


www.spirent.com 33

2.10. Configure TTworkbench Express Before performing this procedure, make sure you have the new TTworkbench Express 27 license file on the external USB drive. 1. Make sure the USB drive containing the new TTworkbench Express license file is connected

to an available USB 2.0 port in the left column of USB 2.0 ports on the SC10. 2. Using Windows Explorer, select the new TTworkbench Express license on the USB drive,

and copy it to the folder C:\Program Files\Spirent Communications\TestDrive ULTS\TTworkbenchExpress.

3. Right-click on the new license file in the folder C:\Program Files\Spirent Communications\TestDrive ULTS\TTworkbenchExpress and select Rename.

4. Change the file name to LicenseFile.lic. 5. Double-click on the file Setup TT FLEXnet Licensing Server.bat in the folder

C:\Program Files\Spirent Communications\TestDrive ULTS\TTworkbenchExpress. 6. Delete the file license.dat. 7. Double-click on the TTworkbenchExpress desktop shortcut.

The TTworkbench Express Launcher dialog box appears.

Figure 15. TTworkbench Express Launcher dialog box.


www.spirent.com 34

8. Click the Launch button. The TTworkbench Express window appears and displays the License Management dialog box.

Figure 16. License Management dialog box.


www.spirent.com 35

9. Click the Install New License button. The License Configuration dialog box appears.

Figure 17. License Configuration dialog box.

10. Click on the License file option button, and then click the Browse button. The Open dialog box appears.

11. Select the file LicenseFile.lic and then click the Open button. 12. Click the OK button in the License Configuration dialog box.

TTworkbench Express automatically restarts, and a new license.dat file is automatically created in the folder C:\Program Files\Spirent Communications\TestDrive ULTS\TTworkbenchExpress.


www.spirent.com 36

13. In the TTworkbench Express window, select Help > License Management. The License Management dialog box appears and displays the list of licenses.

Figure 18. License Management dialog box displaying licenses.

14. Click the Close button. 15. Close the TTworkbench Express window. 16. Go to the next section to update Microsoft Security Essentials.


www.spirent.com 37

2.11. Update Microsoft Security Essentials In this section, you will update Microsoft Security Essentials on Controller PC1 and the Application Server.

NOTE: Controller PC1 and the Application Server must have internet access to update Microsoft Security Essentials.

Keep in mind the following information:

• The Scheduled scan feature is turned off by default to prevent a scan from interfering with any tests you may be running.

• Spirent recommends that you perform manual scans (instead of scheduled scans).

• Spirent recommends that you only run a scan when you are not running a test.

NOTE: By default, the Windows Update feature is disabled on Controller PC1 and the Application Server to prevent an automatic update from interfering with any tests you may be running.

2.11.1. Update Microsoft Security Essentials on Controller PC1 Perform the following steps: 1. At the top of the window, click QEMU and select QEMU (ControllerPC1). 2. On Controller PC1, access the System tray, and double-click on Microsoft Security

Essentials as shown in the following figure.

Figure 19. Microsoft Security Essentials icon in the System tray.


www.spirent.com 38

The Microsoft Security Essentials window appears and displays the Home tab.

Figure 20. Home tab in the Microsoft Security Essentials window.


www.spirent.com 39

3. Click on the Update tab. The Update tab appears.

Figure 21. Update tab in the Microsoft Security Essentials window.

4. Click the Update definitions button. The latest Microsoft Security Essential virus and spyware definitions are downloaded and installed. This process may take up to 10 minutes. When the update is complete, the message Up to date appears.

5. After the latest definitions are downloaded, click on the Home tab. The Home tab appears.

6. In the Scan options area, make sure the Quick option button is selected. 7. Click the Scan now button.

When the scan is complete, the message Scan completed appears.


www.spirent.com 40

8. Perform one of the following steps: If no threats were detected, go to Step 9. If the message The app detected a potential threat on your PC appears, perform the

following steps: a. Click the Clean PC button.

The Potential threats details dialog box appears and shows the status of the process. When the process is complete, a dialog box appears stating that your actions were applied successfully.

b. Click the Close button. c. Click on the History tab. d. Click the check box for the detected item. e. Click the Remove button.

The selected item is removed. 9. Close the Microsoft Security Essentials window. 10. Go to the next section to update Microsoft Security Essentials on the Application Server.


www.spirent.com 41

2.11.2. Update Microsoft Security Essentials on the Application Server Perform the following steps: 1. At the top of the window, click QEMU and select QEMU (ApplicationServer).

The Application Server desktop appears. 2. Access the System Tray, and double-click on Microsoft Security Essentials as shown in

the following figure.

Figure 22. Microsoft Security Essentials icon in the System Tray.




www.spirent.com 42






When the scan is complete, a message appears stating whether any potential threats were detected.


www.spirent.com 43





The selected item is removed. 9. Close the Microsoft Security Essentials window. 10. At the top of the window, click QEMU and select QEMU (ControllerPC1).

The Controller PC1 desktop appears. 11. Go to the next section to upgrade the WTS122-CA.


www.spirent.com 44

2.12. Upgrade the WTS122-CA This section describes how to install WTS122-CA software version 2.10.04 on the WTS122-CA via a USB drive and update Microsoft Security Essentials on the WTS122-CA. To upgrade the WTS122-CA and update Microsoft Security Essentials, you must perform the following steps: 1. Install the new WTS122-CA software you downloaded from the Spirent CSC. 2. Sign into the WTS122-CA and verify the installation. 3. Update Microsoft Security Essentials.

2.12.1. Install WTS122-CA Software Version 2.10.04 Use this procedure to install software version 2.10.04 on the WTS122-CA via a USB drive. Perform the following steps: 1. Connect the external USB drive to one of the USB ports located on the rear panel of the

WTS122-CA.

NOTE: If a keyboard and mouse are connected to the USB ports on the rear panel of the WTS122-CA, remove the keyboard from the USB port, and connect the external USB drive into that USB port.

The following figure shows the location of the USB ports on the rear panel of the WTS122-CA.

Figure 25. Location of USB Ports on the Rear Panel of the WTS122-CA.


www.spirent.com 45

2. Access the 8100 Services Management Utility on the SC10. 3. In the 8100 Services Management Utility, click the Tools button.

The Tools page appears. 4. In the WTS Interfaces area, click the Open Management Utility button.

A new browser tab appears and displays the WTS Instrument Management Utility. 5. Click the SOFTWARE INSTALLATION button.

The Software Installation page appears. 6. In the Select a software channel area, click the Search local home folder (/home/wts/)

and removable media for software channels button. The Operation Results area displays the message that it is searching for the home folder and removable media for WTS software. When the process is complete, the message Success: 1 channel(s) added appears in the Operation Results area, and the message Operation Complete appears at the bottom of the page.

7. Click the Return to Management Window button. The URL for the local channel containing the .tar file appears in the bottom row of the table in the Select a software channel area.

8. In the Select a software channel area, click the Enable button for the channel you added (for example, WTSLocal1). The software components from the .tar file of the channel you selected appear in the table in the Software release available from selected software channel area. The Install button appears for each software component. The Upgrade Instrument Management Utility button appears in the Software releases available from selected software channel area if the WTS Instrument Management Utility software must be upgraded.

9. If the Upgrade Instrument Management Utility button appears in the Software releases available from selected software channel area, perform the following steps: a. Click the Upgrade Instrument Management Utility button.

A dialog box appears, prompting you to confirm your action. b. Click the OK button.

The WTS Instrument Management Utility is upgraded. When the upgrade is complete, the Software Personalities page appears.

c. Click the SOFTWARE INSTALLATION button. The Software Installation page appears.


www.spirent.com 46

10. In the Software releases available from selected software channel area, click the Install button for Version 2.10.04. A dialog box appears, prompting you to confirm that you want to install the selected software package.

11. Click the OK button. 12. If a message box appears stating that the instrument will restart when the installation is

complete, click the OK button. The upgrade process begins. The upgrade process may take up to 20 minutes. During this process, the WTS Instrument Management Utility displays the operation results.

WARNING! Do not refresh the browser or power down the WTS122-CA during the upgrade process.

When the upgrade is complete, the WTS122-CA restarts. 13. Close the browser tab for the WTS Instrument Management Utility window. 14. Disconnect the external USB drive from the rear panel of the WTS122-CA.

NOTE: If a keyboard and mouse are connected to the USB ports on the rear panel of the WTS122-CA, reconnect the keyboard into the USB port on the rear panel of the WTS122-CA.

15. Go to the next section to verify your installation.


www.spirent.com 47

2.12.2. Verify Your Installation Use this procedure to sign into the WTS122-CA and verify that you can reserve the WTS122-CA. Perform the following steps: 1. In the 8100 Services Management Utility, click the Tools button.

The Tools page appears. 2. In the WTS Interfaces area, click the Open Elevate GUI button.

A new browser tab appears and displays the Spirent sign in page after the WTS122-CA boots up.

Figure 26. Spirent Sign In page for the WTS122-CA.


www.spirent.com 48

3. On the Spirent sign in page, enter admin in the Username box. 4. In the Password box, enter admin. 5. Click the Sign in button.

The Dashboard page appears. In the Instruments area, a solid green circle and the Reserve button are displayed next to the WTS122-CA, indicating that the WTS122-CA is available for use.

Figure 27. Sample Dashboard page for a WTS122-CA.


www.spirent.com 49

6. In the Instruments area, click the Reserve button for the WTS122-CA. The solid green circle for the WTS122-CA changes to a green circle with white diagonal lines, and the Reserve button changes to the Release button. The WTS122-CA is working properly and can be used for testing.

Figure 28. Reserved WTS122-CA.

7. In the Services area, click the Enable button. If you have a license for the internal ProLab Service provided by the WTS122-CA, a green circle with white diagonal lines is displayed next to Internal ProLab Service in the Services area, indicating that internal ProLab Service is enabled.

Figure 29. Enabled Internal ProLab Service.

8. Click the Sign Out link at the top of the page. The WTS122-CA is now upgraded.

9. Close the browser tab for the WTS122-CA GUI. 10. Go to the next section to update Microsoft Security Essentials.


www.spirent.com 50

2.12.3. Update Microsoft Security Essentials In this section, you will update Microsoft Security Essentials on the WTS122-CA. For this procedure, you must connect a keyboard, mouse, and monitor to the WTS122-CA.

NOTE: The WTS122-CA must have internet access to update Microsoft Security Essentials.

Keep in mind the following information:

• The Scheduled scan feature is turned off by default to prevent a scan from interfering with any long tests you may be running.

• Spirent recommends that you perform manual scans (instead of scheduled scans).

• Spirent recommends that you only run a scan when you are not running a test.

NOTE: By default, the Windows Update feature is disabled on the WTS122-CA to prevent an automatic update from interfering with any tests you may be running.

For this procedure, you will need to connect a monitor, a keyboard, and a mouse to the WTS122-CA. Perform the following steps: 1. Connect the monitor to the monitor port on the rear panel of the WTS122-CA. 2. Connect the keyboard to a USB port on the rear panel of the WTS122-CA. 3. Connect the mouse to a USB port on the rear panel of the WTS122-CA.

NOTE: You must connect the keyboard and mouse to the USB ports on the rear panel of the WTS122-CA. These devices will not function properly if connected to the USB ports on the side of the WTS122-CA.


www.spirent.com 51

4. On the WTS122-CA, minimize the Spirent sign in page to view the desktop. 5. Click Start>All Programs>Microsoft Security Essentials.




www.spirent.com 52






When the scan is complete, a message appears stating whether any potential threats were detected.


www.spirent.com 53





The selected item is removed. 12. Close the Microsoft Security Essentials window. 13. Access the 8100 Services Management Utility on the SC10. 14. In the 8100 Services Management Utility, click the Tools button.

The Tools page appears. 15. In the WTS Interfaces area, click the Open Management Utility button.

A new browser tab appears and displays the WTS Instrument Management Utility.

NOTE: You MUST access the WTS Instrument Management Utility from the 8100 Services Management Utility. Do NOT access the WTS Instrument Management Utility using the keyboard and mouse connected to the WTS122-CA.

16. Click the TOOLS button. The Tools page appears.


www.spirent.com 54

Figure 32. Tools page in WTS Instrument Management Utility.

17. Click the Commit VM Changes button at the bottom of the page to save the changes you made in Microsoft Security Essentials. The Operation Results page appears.

Figure 33. Save button in the Operation Results page.


www.spirent.com 55

18. Make sure ControllerPC is displayed in the drop-down list box, and click the Save button. A dialog box appears prompting you to save data to the Controller PC.

19. Click the OK button. The WTS122-CA saves the changes and restarts.

20. When the Spirent sign in page appears on the monitor that is connected to the WTS122-CA, close the browser tab for the WTS Instrument Management Utility window on the SC10.

21. Go to the next section to install test suites.


www.spirent.com 56

2.13. Install the Test Suites Refer to the appropriate test suite system release summary to install the test suites. After installing the test suites, go to the next section to configure the GSS7000.

2.14. Upgrade GSS7000 NOTE: If you want to use a standalone GSS7000 with the LTS system, contact Spirent Support.

Perform this procedure if you are using a GSS7000.

NOTE: You can use the GSS7000 with both an LTS B-Series system and an LTS Q750 system. In this case, you must restart the GSS7000 after you activate the personality of the LTS system you want to use (that is, LTS 13.1 or LTS Q750 4.1).

Perform the following steps: 1. On the Controller PC, select Start > All Programs > Accessories > Remote Desktop

Connection. The Remote Desktop Connection window appears.

2. In the Computer box, enter the IP address of the GSS7000 (192.168.0.46). 3. Click the Options button.

The User name box and tabs appear in the Remote Desktop Connection window. 4. In the User name box, type gpsadmin. 5. Click the Local Resources tab.

The Local Resources tab appears. 6. Click the More button.

The Local devices and resources dialog box appears. 7. In the Local devices and resources dialog box, select (check) the Drives check box, and

then click the OK button. 8. In the Remote Desktop Connection window, click the Connect button. 9. If a Remote Desktop Connection dialog box appears asking whether you trust this remote

connection, click the Connect button. The Windows Security dialog box appears.

10. In the Password box, type admin and click the OK button. 11. If a Remote Desktop Connection dialog box appears stating that the identity of the remote

computer cannot be verified, click the Yes button. The GSS7000 desktop appears.


www.spirent.com 57

12. Click on the Start button and select Control Panel. The All Control Panel Items window appears.

13. Click on Programs and Features. The Programs and Features window appears.

14. Find PosApp and look at the build number.

Figure 34. PosApp application in the Programs and Features window.

15. Perform one of the following steps: If PosApp version 6.05.008 or later is installed, go to Step 16 to upgrade the PosApp

Launcher application. If PosApp version 6.05.008 or later is NOT installed, perform the following steps:

a. Select PosApp and click the Uninstall button. The Programs and Features dialog box appears prompting you to confirm your action.

b. Click the Yes button. c. After the program is uninstalled, press the power button on the front panel of the

GSS7000 to reboot the GSS7000. d. After the GSS7000 reboots, select Start > All Programs > Accessories > Remote

Desktop Connection on the Controller PC. The Remote Desktop Connection window appears.


www.spirent.com 58

e. In the Computer box, enter the IP address of the GSS7000 (192.168.0.46). f. Click the Options button.

The User name box and tabs appear in the Remote Desktop Connection window. g. In the User name box, type gpsadmin. h. Click the Local Resources tab.

The Local Resources tab appears. i. Click the More button.

The Local devices and resources dialog box appears. j. In the Local devices and resources dialog box, select (check) the Drives check box,

and then click the OK button. k. In the Remote Desktop Connection window, click the Connect button. l. If a Remote Desktop Connection dialog box appears asking whether you trust this

remote connection, click the Connect button. The Windows Security dialog box appears.

m. In the Password box, type admin and click the OK button. n. If a Remote Desktop Connection dialog box appears stating that the identity of the

remote computer cannot be verified, click the Yes button. The GSS7000 desktop appears.

o. Using Windows Explorer, go to the folder D:\posapp\conf and double-click on the file update_patch-list.txt.

p. In the Notepad window, find the <version> tag under the section “The Host Controller Base Image” as shown in the following figure.

Figure 35. Sample <version> tag in the update_patch-list.txt file.

q. Make a note of whether the version number is 4.x.x or 3.x.x. r. Close the Notepad window.


www.spirent.com 59

s. Go to the folder LTS Q750 v4.1.0 SC10 Installer\8100 MDTS Q750 v4.1.0\LBS Utilities\GSS7000\PosApp on the external USB drive, and perform one of the following steps to install PosApp: If the version number in Step P is 4.x.x, double-click on the file

PosApp_setup_V6_05_Yocto_2pt1_prelim08.exe. If the version number in Step P is 3.x.x, double-click on the file

PosApp_setup_V6_05_Yocto_1pt5_prelim08.exe. t. After the program is installed, press the power button on the front panel of the

GSS7000 to reboot the GSS7000. u. After the GSS7000 reboots, select Start > All Programs > Accessories > Remote

Desktop Connection on the Controller PC. The Remote Desktop Connection window appears.

v. In the Computer box, enter the IP address of the GSS7000 (192.168.0.46). w. Click the Options button.

The User name box and tabs appear in the Remote Desktop Connection window. x. In the User name box, type gpsadmin. y. Click the Local Resources tab.

The Local Resources tab appears. z. Click the More button.

The Local devices and resources dialog box appears. aa. In the Local devices and resources dialog box, select (check) the Drives check box,

and then click the OK button. bb. In the Remote Desktop Connection window, click the Connect button. cc. If a Remote Desktop Connection dialog box appears asking whether you trust this

remote connection, click the Connect button. The Windows Security dialog box appears.

dd. In the Password box, type admin and click the OK button. ee. If a Remote Desktop Connection dialog box appears stating that the identity of the

remote computer cannot be verified, click the Yes button. The GSS7000 desktop appears.

ff. Click on the Start button and select Control Panel. The All Control Panel Items window appears.

gg. Click on Programs and Features. The Programs and Features window appears.

hh. Go to the next step to upgrade the PosApp Launcher application.


www.spirent.com 60

16. In the Programs and Features window, find PosApp Launcher and look at the build number.

Figure 36. PosApp Launcher application in the Programs and Features window.

17. Perform one of the following steps: If PosApp Launcher version 1.0.1 or later is installed, the GSS7000 upgrade is complete. If PosApp Launcher version 1.0.1 or later is NOT installed, perform the following steps:

a. Right-click on the task bar at the bottom of the display, and select Start Task Manager as shown in the following figure.

Figure 37. Starting Windows Task Manager.

The Windows Task Manager window appears.


www.spirent.com 61

b. In the Windows Task Manager window, click on the Processes tab. c. Select PosAppLauncher.exe and click the End Process button as shown in the

following figure.

Figure 38. Starting Windows Task Manager.

The Windows Task Manager dialog box appears, prompting you to confirm your action.

NOTE: If PosAppLauncher.exe is not displayed, go to Step e.

d. Click the End Process button. e. Close the Windows Task Manager window. f. In the Programs and Features window, select PosApp Launcher and click the

Uninstall button. The Programs and Features dialog box appears prompting you to confirm your action.


www.spirent.com 62

g. Click the Yes button. h. Close the Programs and Features window. i. Perform one of the following steps: If the GSS7000 is using Windows 7, go to the folder LTS Q750 v4.1.0 SC10

Installer\8100 MDTS Q750 v4.1.0\LBS Utilities\GSS7000\PosApp Launcher\Win7 OS on the external USB drive, and double-click on the file PosAppLauncher.msi to install PosApp Launcher.

If the GSS7000 is using Windows 10, go to the folder LTS Q750 v4.1.0 SC10 Installer\8100 MDTS Q750 v4.1.0\LBS Utilities\GSS7000\PosApp Launcher\Win10 OS on the external USB drive, and double-click on the file PosAppLauncher.msi to install PosApp Launcher.

j. After the PosAppLauncher is installed, press the Power button on the front panel of the GSS7000 to reboot the GSS7000. The GSS7000 upgrade is complete.

NOTE: If you want to use the GPS L5 support feature, contact Spirent Support to upgrade your GSS7000 box with the GPS L5 capability.


www.spirent.com 63

3. Windows and Simple DNS Activation

3.1. Overview This chapter describes how to activate Windows and Simple DNS. Perform the procedures in this section if you are unable to activate Windows and Simple DNS automatically using the VMSync Tool (for example, there is no internet connection).

3.2. Step 1: Activate Windows via a Phone This section describes how to activate Windows via a phone. Perform the procedure in this section if you are unable to activate Windows automatically using the VMSync Tool (for example, there is no internet connection).

NOTE: To activate the Windows license, you can use a smart phone. You will receive a text message from Microsoft containing a link that will enable you to activate the license.

If you are unable to activate Windows via the VMSync Tool, the following Internet Connection Test dialog box appears.



www.spirent.com 64

Perform the following steps: 1. In the Internet Connection Test dialog box, click the No button.

The following Windows Activation message box appears.


2. Click the OK button. The following Windows Activation dialog box appears.

Figure 41. Windows Activation dialog box.


www.spirent.com 65

3. Click the See other ways to activate button. The following Windows Activation dialog box appears.

Figure 42. How do you want to activate Windows? dialog box.


www.spirent.com 66

4. Click on the Use the automated phone system button. The following Windows Activation dialog box appears.

Figure 43. Find available phone numbers for activation dialog box.


www.spirent.com 67

5. From the drop-down list box, select your nearest location, and click the Next button. A Windows Activation dialog box appears displaying the telephone number and instructions for activating Windows by phone.

Figure 44. Sample Activate Windows now dialog box.

6. Call the phone number provided for the Microsoft Activation Center. 7. When prompted, say that you want to activate Windows. 8. When prompted, say that you want to use smart phone display. 9. When prompted, enter your smart phone number. 10. After you receive a text message with a link from Microsoft, hang up.


www.spirent.com 68

11. Click on the link in the text message. The Product Activation page appears.

Figure 45. Product Activation page.

12. Press on 6 Digits. The Please Enter Your Installation ID page appears.

Figure 46. Please Enter Your Installation ID page.


www.spirent.com 69

13. Enter the installation ID displayed on the Controller PC. 14. Press the Submit button.

The Confirmation ID page appears.

Figure 47. Sample Confirmation ID page.

15. Enter the confirmation ID from Microsoft in the Windows Activation dialog box on the Controller PC.


www.spirent.com 70

16. Click the Next button on the Controller PC. A Windows Activation message box appears on the Controller PC stating that the activation was successful.

Figure 48. Activation was successful message box.

17. Click the No button on your smart phone. You receive the page “Great! Your product has been successfully activated.”

18. Press the Goodbye button on your smart phone. 19. Click the Close button in the Windows Activation message box. 20. Go to the next section to active Simple DNS for the Controller PC.


www.spirent.com 71

3.3. Step 2: Activate Simple DNS This section describes how to manually activate the Simple DNS license for the Controller PC. Before performing this procedure, make sure you have:

• A valid Simple DNS license • A PC that has internet access • A USB drive to transfer a text file from the SC10 to the PC that has internet access Perform the following steps: 1. In the Simple DNS Plus Licensing dialog box, click the I already have a license option

button. 2. In the associated text box, type the Simple DNS license, and then click the Activate button.

A message appears stating that it is requesting activation from the internet server. After the request fails because there is no internet access, the message Failed to activate license automatically! appears, and a link to activate the license manually is provided. The following figure shows a sample link.

Figure 49. Sample Simple DNS Plus Licensing activation link.


www.spirent.com 72

3. Click the Copy button. 4. Click the Start button and select All Programs > Accessories > Notepad.

The Notepad window appears. 5. In the Notepad window, click the Edit menu and select Paste.

The link you copied from the Simple DNS Plus Licensing dialog box is pasted in the Notepad window.

6. Click the File menu and select Save As. The Save As dialog box appears.

7. In the File name box, type SimpleDNSlicense and then click the Save button. 8. Exit the Notepad window. 9. Insert USB drive into an available USB 2.0 port on the SC10. 10. Using Windows Explorer, go to the folder Libraries\Documents and copy the file

SimpleDNSlicense.txt to the USB drive. 11. Remove the USB drive, and connect it to an available port on the PC that has internet

access. 12. Open a web browser on the PC. 13. Double-click on the file SimpleDNSlicense.txt on the USB drive.

The Notepad window appears and displays the link you copied from the Controller PC. 14. Select and copy the link in the Notepad window. 15. Paste the link into the browser, and press the ENTER key.

The Product Activation page appears and displays the license activation signature for Simple DNS. The following figure shows a sample license activation signature.

Figure 50. Sample License Activation Signature.


www.spirent.com 73

16. Select and copy the information displayed in the License activation signature box. 17. Access the Notepad window displaying the file SimpleDNSlicense.txt and insert 2 new

lines at the bottom of the file. 18. Put the cursor on the last line in the file, click the Edit menu, and select Paste.

The activation link appears at the bottom of the Notepad file. 19. Click the File menu, and select Save. 20. Exit the Notepad window. 21. Remove the USB drive and connect it to an available USB 2.0 port on the SC10. 22. Copy the new file to the D: drive on the SC10. 23. Access the D: drive on the SC10, and double-click on the file SimpleDNSlicense.txt.

The Notepad window appears and displays the license activation signature you copied from the browser on your PC.

24. Select and copy the license activation signature that is located at the bottom of Notepad window.

25. Paste the license activation signature into the text box at the bottom of the Simple DNS Plus Licensing dialog as shown in the following figure.

Figure 51. Sample Simple DNS Plus Licensing dialog box with license activation signature.


www.spirent.com 74

26. Click the Activate button. A Simple DNS Plus message box appears stating that the license activated successfully.

Figure 52. Simple DNS Plus Licensing message box for successful activation.

27. Click the OK button. 28. Exit the Notepad window.

Simple DNS Plus license activation is complete.


www.spirent.com 75

4. Software License Agreement By using Spirent 8100 Mobile Device Test System Location Test System Q750 platform version 4.1, you accept the terms of the following Spirent Communications Inc. software license agreement.

SPIRENT COMMUNICATIONS, INC. SOFTWARE LICENSE AGREEMENT

This Software License Agreement (“Agreement”) is made by and between (i) Spirent Communications, Inc. and its affiliates (“Spirent”), and (ii) you, the user ("Customer"), who, intending to be legally bound and for good and valuable consideration hereby acknowledge and agree as follows. If you are accepting the terms of this Agreement on behalf of an entity, you and such entity represent and warrant that you have the authority to bind such entity to this Agreement, and, in such event, “Customer” will refer to such entity.

THIS AGREEMENT GOVERNS CUSTOMER’S USE OF SPIRENT SOFTWARE, INCLUDING EMBEDDED OR PRE-INSTALLED SOFTWARE IN SPIRENT HARDWARE, (THE “SOFTWARE”), UNLESS SPIRENT AND CUSTOMER HAVE EXECUTED A SEPARATE AGREEMENT THEREFOR. BY CLICKING “I ACCEPT” OR OPERATING, DOWNLOADING, INSTALLING, REGISTERING OR OTHERWISE USING THE SOFTWARE, CUSTOMER IS EXPRESSLY ACKNOWLEDGING AND AGREEING THAT THIS IS A BINDING AGREEMENT AND CUSTOMER HEREBY AGREES TO THE TERMS OF THIS AGREEMENT. IF CUSTOMER DOES NOT ACCEPT ALL THE TERMS AND CONDITIONS SET FORTH HEREIN, CUSTOMER MAY NOT OPERATE, DOWNLOAD, INSTALL, REGISTER OR OTHERWISE USE THE SOFTWARE.

1. SOFTWARE LICENSE 1.1. Licensed Rights. Subject to the terms and conditions of this Agreement, Spirent grants to Customer a limited, nonexclusive, nontransferable license, without right of sublicense, to use, solely for Customer’s internal business purposes, the Software, in object code form only and only in accordance with (a) the technical specification documentation generally made available by Spirent to its customers with regard to the Software (“Documentation”), (b) this Agreement and (c) any term, user, number of licenses or other restrictions set forth in the applicable Spirent quotation (“Quote”) or, if not expressly specified in such Quote, the number of licenses, users and/or test sessions for the part numbers listed in Spirent’s price list as of the date of such Quote. Licenses designated as “subscription” licenses are for a twelve (12) month period only (unless otherwise designated in the Quote), and shall automatically renew for subsequent periods of the same length at the then-current price unless either party provides the other party with notice of cancellation thirty (30) days or more prior to the expiration of the then-current term. Software shall also include any Documentation and any maintenance and support releases, improvements, enhancements, and other updates of the same Software product provided to Customer under this Agreement. The Quote shall specify the license type for each license of the Software:

Global Floating: Customer may install the Software on any number of internal systems and any of Customer’s employees, consultants or agents may use the Software on behalf of Customer, provided however, no more than the specified maximum number of simultaneous instances may be executed at any one time.

Floating: Customer may install the Software on any number of internal systems and any of Customer’s employees, consultants or agents may use the Software on behalf of Customer, provided however, that (i) no more than the specified maximum number of simultaneous instances may be executed at any one time, and (ii) the Software may not be installed on any system or used by any user outside of the specified jurisdisction(s).

Named: Customer may only permit one registered, unique named individual to use each licensed instance of the Software and may only be installed on a reasonable number of systems utilized by such individuals. Named licenses must be registered with the individual’s actual name


www.spirent.com 76

and may not be shared by individuals or allocated to a job function. Once a license is associated with an individual, the license may not be transferred to another individual without the express prior written consent of Spirent.

Node Locked: Customer may install each license of the Software on one specific system and that system is the only one which may access that instance of the Software. Once a license is associated with a specific system, the license may not be transferred to another system without Spirent’s prior written consent.

Spirent and Customer may agree on alternate types of licenses as set forth in a Quote. If no license type is specified in a Quote, the Software is licensed as a one-year subscription of a single Named license.

1.1.1. Pre-installed Software. To the extent that the Software is pre-installed on Spirent hardware acquired by Customer, Customer may use such Software solely as installed on and to the extent necessary for the normal and intended uses of, such Spirent hardware, subject to the terms of this Agreement.

1.2. Restrictions on Licensed Rights. Customer acknowledges that the components of the Software are subject to copyrights owned by Spirent or its licensors and the Software is licensed, and not sold, to Customer. Customer is prohibited from modifying or permitting anyone else to modify the Software or any module or other portion thereof. Except as necessary to exercise the rights expressly granted in this Agreement, Customer is prohibited from copying or duplicating, or permitting anyone else to copy or duplicate the Software or any module or other portion thereof, other than for purposes of replacing a worn copy or creating an archive copy. Any such copy shall contain the same copyright notice and proprietary markings as the copy of the Software furnished by Spirent to Customer hereunder. In addition to the other restrictions in this Agreement, and other than as may be required or impermissible by applicable law or third-party licenses, Customer shall not, and shall not permit others to: (i) create derivate works, distribute, transmit, license or otherwise transfer the Software directly or through third parties; (ii) reverse engineer, disassemble, decompile the Software or any component of the Software or otherwise attempt to obtain the source code of the Software; (iii) use the Software in a service bureau environment nor use the Software to process any data other than Customer’s own internal data; or (iv) use the Software for any illegal or malicious purpose or to access any information not owned by Customer or for which it does not have express permission to access; (v) tamper with, or attempt to circumvent or disable, any license key; or (vi) use the Software on any networks, devices or applications not owned or controlled by the Customer. The Software may contain certain devices or mechanisms that Spirent may use to disable or terminate Customer’s access to or use of the Software upon the breach or termination of Customer’s license thereto. Nothing in this Agreement limits or restricts the rights granted to Customer under the license terms applicable to the open source or other third-party software provided hereunder.

1.3. U.S. Government Users. The Software is commercial computer software and commercial computer software documentation within the meaning of the applicable acquisition regulations. If acquired by or on behalf of a civilian agency of the United States government, the Software will be subject to terms of this Agreement as a “license customarily provided to the public” as specified in 48 C.F.R. ch. 1 Part 12.212 of the Federal Acquisition Regulations and its successors. If acquired by or on behalf of units of the Department of Defense, it will be subject to the terms of this Agreement as a “license customarily provided to the public “as specified in 48 C.F.R. ch. 1 Part 227.7202, DFAR Supplement and its successors. If Spirent receives a request from any Customer agency of the U.S. Government to provide Software with rights beyond those stated above, Spirent will promptly, in its sole discretion, accept or reject such request.


www.spirent.com 77

2. INVOICING/PAYMENTS 2.1. License subject to Payment. The license of the Software granted under this Agreement is subject to the payment of Spirent’s then-current list price for the Software or such other amount as set out in the Quote (“Fees”).

2.2. Payment of Fees. Customer shall pay Spirent the Fees for the Software and any associated software or services net thirty (30) days from the date of Spirent’s invoice for the same. Spirent reserves the right to establish or change credit terms based on Customer’s payment history and financial condition. If Customer wishes to expand the scope of its license, additional agreed-upon license fees shall become due and payable to Spirent prior to the effective date of any expansion of the scope of the Customer’s license. Such invoice shall be issued in accordance with the Quote or absent such a Quote upon the delivery or download of the Software whichever is the earlier. Any amounts not paid within such thirty (30) day period shall bear interest at the lesser of the maximum rate allowable in the Customer’s state or two percent (2%) per month. Customer’s payment of such interest on late payments shall not prevent Spirent from exercising any other rights under this Agreement or applicable law. Except as required by applicable law or as set forth in Section 5.2.1, all Fees are non-refundable and non-cancelable and will be paid in US dollars.

2.3. Taxes. All amounts described herein are exclusive of all federal, state, municipal or other governmental excise, sales, value-added, use, personal property and occupational taxes, excises, withholding obligations and other levies now in force or enacted in the future and accordingly, all Fees are subject to an increase equal to the amount of any tax Spirent may be required to collect or pay in connection with the Software, other than any tax on the net income of the Spirent.

3. PROPRIETARY RIGHTS; CONFIDENTIAL INFORMATION 3.1. Ownership of Software. Other than the limited licenses set forth in this Agreement, any and all rights, title and interest in and to the Software, and the intellectual property and proprietary rights to the Software, shall not pass to Customer, but shall remain the exclusive property of Spirent or its licensors.

3.2. Spirent Confidential Information. Customer acknowledges that the following categories of information constitute Spirent Confidential Information: (a) all components of the Software; and (b) the terms and conditions of this Agreement; and (c) other information disclosed by Spirent that would reasonably be understood to be confidential or proprietary. Spirent Confidential Information will not include, however, any information which: (a) is or becomes part of the public domain through no act or omission of Customer; (b) was in the Customer’s lawful possession prior to the disclosure and had not been obtained by Customer either directly or indirectly from Spirent or the Software; (c) is lawfully disclosed to Customer by a third party without restriction on disclosure; or (d) is independently developed by the Customer. For a period of ten (10) years from and after disclosure of Spirent Confidential Information to Customer, Customer agrees to hold all such Spirent Confidential Information in strict confidence, and agrees not to disclose (or permit others to disclose) it to others or use it in any way, commercially or otherwise, except in exercising its rights pursuant to this Agreement. Customer shall not disclose any Spirent Confidential Information to a recipient not authorized in writing by Spirent or use the Confidential Information for any purpose not expressly authorized by this Agreement. Any disclosures by Customer of Spirent Confidential Information shall only be to Customer’s employees, consultants, or agents as expressly permitted hereunder on a “need to know” basis for the purposes of this Agreement and subject to such third parties’ acceptance of terms and conditions with respect to the disclosed information at least as restrictive as those set forth in this Agreement. If Customer is compelled by law or a court of competent jurisdiction to disclose Spirent Confidential Information, Customer will promptly notify Spirent in writing and will cooperate at Spirent’s expense in seeking a protective order or other appropriate remedy. If disclosure is ultimately required, Customer will furnish only that portion of Spirent Confidential Information that is legally required and will exercise reasonable efforts to obtain assurance that it will receive confidential treatment.

3.3. Equitable Relief. Licensee acknowledges that any breach of its obligations with respect to the proprietary rights or confidential information of Spirent or its licensors may cause Spirent and its licensors irreparable injury for which there would be inadequate remedies at law, and Spirent and its licensors will


www.spirent.com 78

be entitled to equitable relief, in addition to all other remedies available to it, without the payment of any bond.

4. TERMINATION 4.1. Termination. This Agreement may be immediately terminated by Spirent in the event: (a) Customer becomes insolvent, files or has filed against it a petition in bankruptcy, or ceases doing business; or (b) the Customer breaches the terms this Agreement.

4.2. Customer Obligations Upon Termination. Upon termination of this Agreement for any reason, (a) all licenses granted to Customer hereunder shall immediately terminate and Spirent may disable access to the Software, (b) Customer shall discontinue use of the Software and the other Spirent Confidential Information, and any portion thereof, and return the Software and any and all other Spirent Confidential Information in its possession to Spirent, or, at Spirent’s option, destroy the Software and such other Spirent Confidential Information, including all copies or partial copies thereof, and shall certify to Spirent in writing that Customer has retained none of the Spirent Confidential Information, and (c) all outstanding Fees shall become due and payable immediately. The following Sections will survive the expiration or termination of this Agreement: 1.2, 2, 3, 4.2, 5, 7, and 8.

5. LIMITED WARRANTIES AND INDEMNIFICATION; EXCLUSIVE REMEDIES 5.1. Software. For a period of ninety (90) days from the date of delivery of the Software to Customer, or such other period as stated in the Quote accepted in writing by Spirent, Spirent warrants to Customer that the Software, if used in accordance with this Agreement, will operate in material conformity with the specifications for the Software which Spirent may publish. The warranties set forth herein do not apply to any material deviation from the accompanying documentation or specifications which results from (a) modification of the Software by anyone other than Spirent or in accordance with Customer’s instructions, (b) use of the Software for any purpose other than intended, (c) use of Software in combination with any other software or devices, if such claim would have been avoided but for such combination, (d) any misuse or incorrect use of the Software, (e) Customer’s failure to use the latest release of the Software provided by Spirent, or (f) any hardware malfunction. CUSTOMER EXPRESSLY ACKNOWLEDGES THAT BECAUSE OF THE COMPLEX NATURE OF COMPUTER SOFTWARE, SPIRENT CANNOT AND DOES NOT WARRANT THAT THE FUNCTIONS CONTAINED IN THE SOFTWARE WILL MEET A SPECIFIC REQUIREMENT OR THAT THE OPERATION OF THE SOFTWARE WILL BE WITHOUT INTERRUPTION OR ERROR-FREE. During the aforementioned warranty period, Spirent will, at Spirent’s expense and as its entire liability (and Customer’s exclusive remedy) for any breach of the warranty and provided Customer has notified Spirent in writing of the nature of the non-conformity within ten (10) days of Customer’s discovery of the non-conformity and provided Spirent is able to verify such non-conformity: (i) correct the non-conformity or (ii) replace the non-conforming Software with Software meeting Spirent’s then-current published specifications.

5.2. Infringement

5.2.1. Cure. In the event of a determination that the Software infringes, or is likely to infringe, any proprietary right of any third party, Spirent shall have the option, at its own discretion and expense, to (a) obtain for Customer the right to continue using the actual or potential infringing component of the Software or (b) replace the actual or potential infringing component of the Software or modify such component so that it becomes non-infringing, or (c) terminate the licensed rights granted herein and grant Customer a refund of the license fee, less reasonable depreciation based on usage, which shall in no event be less than the result of a straight-line computation based upon a five (5) year usable life.

5.2.2. Indemnification. Spirent shall indemnify, defend and hold Customer harmless from and against any and all liability, damages, loss or expense (including reasonable fees of attorneys) arising from any claim, demand, action or proceeding initiated by any third party alleging the Software infringes the copyright, US registered patent or trademark of any third party; provided, however, that as a condition to this indemnification obligation, Customer shall promptly (a) notify Spirent of any threat or initiation of any claim, demand, action or proceeding to which the indemnification obligation may apply, (b) assist Spirent


www.spirent.com 79

in the defense or settlement of the matter, and (c) provide Spirent sole control over the defense and settlement of such matter.

5.2.3. Exclusions. Spirent shall have no obligations under Section 5.2 for any alleged infringement based upon: (a) modification of the Software by anyone other than Spirent, (b) use of the Software in combination with other software or any other Software or devices if such claim would have been avoided but for such combination, (c) Customer’s continued use of the infringing Software after receipt of notice of an infringement claim or after receipt of a remedy from Spirent under this Agreement, (d) Customer’s use of the Software other than in accordance with the terms of this Agreement or Documentation, or (e) modifications to the Software made pursuant to Customer’s express instruction.

THIS SECTION 5.2 STATES SPIRENT’S ENTIRE LIABILITY, AND CUSTOMER’S EXCLUSIVE REMEDY, WITH RESPECT TO ANY INFRINGEMENT OF ANY THIRD-PARTY INTELLECTUAL PROPERTY RIGHTS.

5.3. Disclaimers. THE LIMITED WARRANTIES AND INTELLECTUAL PROPERTY INDEMNIFICATION SET FORTH HEREIN ARE EXCLUSIVE AND IN LIEU OF, AND CUSTOMER HEREBY WAIVES, ALL OTHER REPRESENTATIONS, WARRANTIES AND GUARANTEES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS OF THE SOFTWARE FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT, AND ANY WARRANTIES ARISING BY STATUTE OR OTHERWISE IN LAW OR OUT OF COURSE OF DEALING, COURSE OF PERFORMANCE, OR USAGE OF TRADE.

5.4. Customer Indemnity Against Other Third-Party Claims. If and to the extent that the Software Cyberflood™, AvalancheNEXT™ or Avalanche Commander™ are included in the related Quote or used by the Customer, the Customer further agrees to indemnify, defend and hold harmless Spirent, and any of Spirent’s parent and affiliated companies, and the present and former officers, members, shareholders, directors, employees, representatives, attorneys, insurers and agents of any of these, and their successors, heirs and assigns (each, a “Spirent Indemnified Party”) from and against any and all liability, damages, losses, or expenses (including reasonable attorneys’ fees) incurred by the Spirent Indemnified Party as the result of any claim, demand, action, or proceeding initiated by any third party for Customer’s use of (i) the aforementioned Software or (ii) any other software, devices, or materials used with any of such Software (including, without limitation, a claim of intellectual property infringement), except if and to the extent that such claim is attributable to Spirent’s gross negligence or willful misconduct or is subject to Spirent’s obligations under Section 5.2 of this Agreement. The Spirent Indemnified Party shall promptly notify the Customer of any potential claim covered by this indemnity, and shall cooperate with the Customer, at Customer’s cost, in the investigation and defense of the same. The Customer shall have sole control over the defense and/or settlement of any such claim, but the Spirent Indemnified Party may participate at its own expense with counsel of its choosing and the Customer will not settle any such claim without the Spirent Indemnified Party’s prior written consent (unless such settlement does not impose any obligations, admissions, or liabilities upon the Spirent Indemnified Party).

6. LIMITATION OF LIABILITY 6.1. Limitations and Exclusions. IN NO EVENT SHALL SPIRENT OR ANY OF ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, (INCLUDING WITHOUT LIMITATION ANY DAMAGES OR LIABILITY RELATING TO INTERRUPTION OF SERVICE, COST OF PROCUREMENT OF SUBSTITUTE SOFTWARE, LOST PROFITS, OR LOSS OF DATA), INCURRED BY THE CUSTOMER, WITHOUT REGARD TO CAUSE OR THEORY OF LIABILITY AND REGARDLESS OF WHETHER OR NOT SPIRENT OR ITS SUPPLIERS WERE ADVISED SUCH DAMAGES MIGHT ARISE.

6.2. Maximum Liability. THE LIABILITY OF SPIRENT AND ITS SUPPLIERS UNDER THIS AGREEMENT, WHETHER ARISING OUT OF BREACH OF CONTRACT (INCLUDING BUT NOT LIMITED TO BREACH OF WARRANTY) OR TORT (INCLUDING BUT NOT LIMITED TO NEGLIGENCE AND STRICT LIABILITY) OR ANY OTHER REASON, SHALL IN NO EVENT EXCEED THE TOTAL FEES PAID TO SPIRENT BY CUSTOMER FOR THE SOFTWARE TO WHICH SUCH LIABILITY


www.spirent.com 80

RELATES DURING THE TWELVE (12) MONTH PERIOD PRIOR TO ANY SUCH CLAIM (OR IN THE CASE OF FIRMWARE, TOTAL FEES PAID BY CUSTOMER FOR THE APPLICABLE HARDWARE).

7. DISPUTE RESOLUTION & CHOICE OF LAW AND FORUM 7.1. Governing Law. This Agreement and any disputes arising from or related to it, or its subject matters, shall be governed, resolved and remedied in accordance with the laws of the State of California, USA, without resort to conflict of law principles. The Parties agree that the United Nations Convention on Contracts for the International Sale of Goods is specifically excluded from application to this Agreement.

7.2. Forum. Any action to enforce, arising out of, or relating in any way to, any of the provisions of this Agreement shall be brought and prosecuted in the Federal and State courts of California and the parties consent to the jurisdiction of said courts.

7.3. Compliance with Laws; Export Control Laws. Customer shall be solely responsible for its compliance with, and agrees to comply with, all applicable laws in connection with its use of the Software. Customer acknowledges that the Software may be subject to export controls imposed by the U.S. Export Administration Regulations (the "EAR"). Customer will not export or reexport (directly or indirectly) the Software, or any derivatives of the Software without complying with the EAR or other applicable laws with respect to the export of technology from the United States.

8. GENERAL TERMS 8.1. Amendment; Waiver. No amendment, modification or discharge of this Agreement, and no waiver hereunder, shall be valid or binding unless set forth in writing and duly executed by the party against whom enforcement of the amendment, modification, discharge or waiver is sought. Failure of either party to insist upon strict performance of any of the terms and conditions hereunder, or the delay in exercising any of its remedies shall not constitute a waiver of such terms and conditions or a waiver of any default or remedy.

8.2. Audit. Customer shall maintain complete and accurate records of its use of the Software during the applicable subscription term (if applicable, or otherwise the term of the Agreement) and for 2 years thereafter. Upon 10 days’ written notice from Spirent, and no more than once per calendar year, Customer shall provide Spirent with reasonable access to Customer’s premises during normal business hours to conduct an audit of Customer’s records and systems to verify compliance with this Agreement, including calculation of Fees. Spirent shall bear the costs of any such audit, except that if Customer is found to have violated the terms of this Agreement, in addition to any and all remedies available to Spirent in law or equity, Customer shall reimburse Spirent for all reasonable audit expenses.

8.3. Assignment. This Agreement and any rights granted hereby may not be assigned by Customer, directly or indirectly, including without limitation by merger, sale of assets or stock, change of control, or operation of law, without the prior written consent of Spirent. Spirent may assign any or all of this Agreement and it rights and obligations hereunder. Any attempt by Customer to assign any rights, duties or obligations without such consent shall be void and without force or effect.

8.4. Force Majeure. Spirent shall not be liable for any damages or penalty for any delay in performance of, or failure to perform, any obligation hereunder due to any elements beyond its reasonable control.

8.5. Attorneys fees. If any action is necessary to enforce the terms of this Agreement, Spirent will be entitled to reasonable attorneys' fees, costs and expenses in addition to any other relief to which it otherwise may be entitled.

8.6. Severability. In the event that any of the provisions of this Agreement shall be held by a court or other tribunal of competent jurisdiction to be unenforceable, the remaining portions of this Agreement shall remain in full force and effect.

8.7. Entire Agreement. This Agreement, together with the Quotes, embodies the entire understanding and agreement between the parties with respect to the subject matter hereof and supersedes all oral and written prior or contemporaneous agreements related to such subject matter.


www.spirent.com 81

8.8. Headings. Section and subsection headings contained in this Agreement are inserted for convenience of reference only, shall not be deemed to be a part of this Agreement for any purposes, and shall not in any way define or affect the meaning, construction or scope of any of the provisions hereof.

8.9. Relationship of the Parties. Spirent and Customer will be and shall act as independent contractors, and neither party is authorized to act as an agent or partner of, or joint venturer with, the other party for any purpose. Neither party by virtue of this Agreement shall have any right, power or authority to act or create any obligation, express or implied, on behalf of the other party.

8.10. Third-Party Components. Customer acknowledges that the Software contains components made available to Spirent by third-party suppliers, and Customer agrees that each such supplier is a third-party beneficiary of this Agreement with the right to enforce Customer’s obligations hereunder with respect to the individual components such supplier has supplied.

8.11. Precedence of Documents: The terms and conditions of this Agreement, insofar as they relate to the rights licensed to the Software will control over any conflicting or inconsistent terms contained in any Quote, or Spirent invoice unless otherwise mutually agreed to in writing. No terms in any quotation, purchase quote, acknowledgment or other form provided by Customer will modify this Agreement, regardless of whether Spirent objects to such terms, and any such additional or conflicting terms are expressly rejected. Notwithstanding Section 8.7, the terms and conditions of this Agreement insofar as they relate to matters other than the rights licensed to the Software shall be subject to the terms and conditions of the master purchase agreement between Spirent and Customer (if any) (the “Master Agreement”) only to the extent that such Master Agreement expressly contradicts the terms and conditions of this Agreement.