84084810 fire and gas recovered

7/25/2019 84084810 Fire and Gas Recovered

1/32

1

Fire and Gas system

A basic understanding with our day

to day job


2/32

WHY DO WE NEED FIRE & GAS PROTECTION

SYSTEM????

How it

Works

Looks?

Fire Detection /Mitigationsystems:

Fire Detection

Gas Detection

Fire Suppression systems

CO2, FM200, Deluge

Emergency Shutdown (ESD)Systems

ICSS DCS/F&G/ESD systems.

Emergency Alarm Systems

PA system


3/32

Combustible Gases-Lower & Upper Limits*

Too lean for ignition Too rich for ignition

Clean Air

Combustibles

Lower

Explosive

Limit (LEL)

Upper

Explosive

Limit (UEL)

Typical Combustible

Gas Detector Range

of Measurement

50%

*No differentiation between the terms Explosive and Flammable as applied to the lower and

upper limits of flammability


4/32

How does Gas Detector work?

Detect & measurevapor before

hazardous

concentration is

present

Provide outputs to

enable emergency

action24 VDC

+ -

LEL

0

0

Flammable

hydrocarbon

gas

No fault

4.0 milliamperes


5/32

Types of Gas Detectors

As per operating principle:

1. Catalytic: Combustibles

2. Infrared: Combustibles

3. Electrochemical: Mainly Toxic gases (H2S,Oxygen,Cl, SO2,)

In our plant, we are having Catalytic and Infrared types, they again may bedivided into point or open path detectors

1. Pointwatch Eclipse 2. Open Path Eclipse 3. Catalytic Sensor/CGS


6/32

Catalytic Sensor Operation

Combustible Gas Sensor (CGS)with DCUEX Tx

Flammable

gas

Active Element - Hot wire resistor

coated with catalytic material

Reference Element - Same as active but

without catalyst

Catalytic reaction when contact with

flammable gas generates heat &

changes Active resistance; reference

resistance unchanged

Explosion is prevented by Flame

Arrestor

Constant E or I power source required


7/32

Point Infrared Detector Elements

Gas

Concentration(LEL)

IR Source LampPermeable Gas

Cell

Reference

Signal Detector

Measurement

Signal Detector

Optical Beamsplitter

Optical Filters

IR Transparent Window

Microprocessor

andElectronics

Permeable GasCellSapphire Mirror Theory of OperationThe infrared (IR) method of

gas detection relies on the IR

absorption characteristics of

gases to determine their

presence and concentration.

IR gas detectors consist of anIR light source (transmitter) and

light detector (receiver) to

measure the intensity both at

the absorption wavelength and

a non-absorbed wavelength.

If gas is present in the optical path, it will affect the intensity of

light transmitted between the light source and the detector.

This change in intensity provides the data for determining that a

specific gas, or type of gas is present.


8/32

8

Open Path Gas Detector System Elements

IR Source

Microprocessor

and

Electronics

Gas

Concentration

(LEL)

Reference

Signal Detector

Measurement

Signal Detector

Optical Beamsplitter

Optical Filters

10 - 60 m

Flammable

hydrocarbon

gas

As the IR beam reaches the receiver, it passes through a focusing lens and then passes

through two narrow band IR filtersan active and a reference wavelength. The detector

computes the ratio between the two signals

The instrument's output is a function of gas concentration times the length of thesurveillance path


9/32

9

Fail-Safe Operation

DirtyOpticsandCleanAir

Active Reference

IR Signal Level

HydrocarbonGas

Active Reference

IR Signal Level

CleanAir

Active Reference

IR Signal Level

Active Reference

IR Signal Level

FailedSensor

Active Reference

IR Signal Level

FailedIR-Source

Failed Microprocessor = 0 mA


10/32

EQP Field Devices - Flame

UV/IR (X5200) - Single Frequency Infrared Flame Detector

UV (X2200)UV flame detector

IR (X9800) - Single Frequency Infrared Flame Detector

Multispectrum IR (X3301) -


11/32

Ultraviolet Sensor Operating Principle

Anode

Cathode OiTest Source

Plastichousing

connectors(a,b,c,d)

QuartzEnvelope

Det-Tronics UV Sensor

circuit board

UV photons strike tube cathode

Cathode releases electron

Electron strikes gas molecule

Cascade effect occurs to anode

Discharge is quenched, creates pulse(count) output

Pulse output measured in CPS (countsper second)

counts/gate: # of pulses (cps) requiredto occur within one gate in order toqualify

gate length: unit of time consec. gates: # of consecutive gates

required to be satisfied before a firealarm output is provided


12/32

Arc Rejection Signal Processing


13/32

Analyzes the raw IR sensor signal randomness

Rejects signals that do not meet randomness criteriaNo Fire Alarm

Fire Alarm !

Signal Processing

Automatic optical integrity calibrated to

perform at all operating temperaturesInternal lamps test each sensor at the

precise wavelength once per minute

to verify operation.


14/32

LOGIC & C&E SYMBOL LEGEND

CUSTOMER:

PROJECT: REVDRAWING NUMBERSIZE

B

DRAWING TITLE

CONFIDENTIAL-

THISDRAWINGANDSPECIFICATIONCONTAINPROPRIETARYINFORMATION

ANDANYREPRODUCTION,DISCLOSURE,ORUSETHEREOF IS EXPRESSLYPROHIBITEDWITHOUT WRITTENPERMISSION OF DETECTORELECTRONICSCORPORATION

SCALE:NONE DETECTOR ELECTRONICS CORPORATION6901 WEST 110TH STREETMINNEAPOLIS, MN 55438DESIGN BY:

DATE:

CHECKED

BY:

P.O.

F.O.

ONEPLACETWOPLACESTHREEPLACESFRACTIONS

ANGLES

0.00.000.000X/XXDEGREES

+/-.020+/-.010+/-.005+/-1/32+/-1

TOLERANCEUNLESSOTHERWISESPECIFIED

DESCRIPTIONDATEREV

12345678

D

C

B

A

D

C

B

A

12345678

INITIAL RELEASE03/12/01AA

XXX

Simon Pate

03/12/01

XXX

DETECTOR ELECTRONICS

EAGLE QUANTUM

Lube Oil console

Fuel Gas System

GT Exit/Entry

Enclo

sure

exha

ust

System Cabinet

RRFlextronics

Control Net

X3301

Thermals

DUCTWATCH

DCIO

Area with Detection & Suppression


15/32

Fire Detector Cone of Vision


16/32

How it Communicates

UV/IR Fire Detection

X5200

IR Fire

Detection

X9800

Supervised Inputs Heats,

Smokes and MACsAgent Release

PRESSHERETRYKK HERKNUS GLASSET

BREAK GLASS

BN-300BRANNALARM

Tilpasningsen het

FIREALARM

Interfaceunit

Nr.

No.

UV Fire DetectionX2200

Premier Controller

Operator Interface

Station

running S3

software

Ver 2.8

Ports

Configuration (serial port)RS-485 serial Link (Modbus RTU)

Redundant media ControlNet

OPC

option

MIR Fire Detection

X3301

24 vdc

power supply

Battery PSM

DCIO

Module

HC Gas Detection

Eclipse

Network

Extender

ARM

Signal / Audible

Devices

SAM

IDC

Supervised

Digital

inputs

Toxic Gas Detection

DCU / DCUEX

I/O Modules

Relay

AIM

IPM


17/32

X3301 Multispectrum Infrared Flame Detector

Extended Cone of Vision

Combines the longest detection

range with the best false alarm

rejection capabilities

a calibrated performance test that is

automatically performed once per minute to

verify complete detector operation

capabilities. No testing with an external test

lamp is required. The detector automatically

performs the same test that a maintenance

person with a test lamp would perform

Automatic oi

Magnetic oi / Manual oi


18/32

Smoke Detector


19/32

Ionization Smoke Detector


20/32


21/32

Heat Detector


22/32

Fire Detection Systems

Fusible loopSmoke detector UV/IR detector

3IR detectorThermal detector

Sprinkler


23/32

Suppression Systems

TPP- EG LQ-MCC

TCPP Control Room

TCPP Deluge

ATF

Deluge


24/32

Fire & Gas Panel

Mini-vesda for LQ MCC

FGP#2 - Mimic PanelFGP#1FGP#3 TCPP Mimic Panel

TPP FGP computer

Fusible loop panel


25/32

Alarms

Platform Emergency AlarmAbandon Platform Alarm

Extinguishing Gas to be Released alarm


26/32

Emergency Manual operation


27/32

Enclosed Area Protection


28/32

Manual Release


29/32

Manual Release


30/32

FM-200 Bank


31/32

Emergency Beckons


32/32

84084810 fire and gas recovered

Documents