8_4_1ds

Toledo Refinery

Site Technical Practices EP 8-4-1DS

Cooling Towers Data Sheet

August 2007 Revision 0.0

Page 1 of 4

Maintained by E2G Shaker Heights, OH

PROJECT

PROJECT NO.

INQUIRY NO.

LOCATION

UNIT

EQUIPMENT ID

JOB NO.

DOCUMENT NO.

DATA ISSUED FOR

IN-HOUSE REVIEW

TOLEDO REFINERY APPROVAL

QUOTATION

PURCHASE

CONSTRUCTION

THIS SHEET IS A RECORD OF EACH ISSUE OR REVISION TO THE SUBJECT DATA. EACH TIME THE DATA IS CHANGED ONLY THE NEW OR REVISED DATA SHEETS NEED TO BE ISSUED. THE EXACT SHEETS CHANGED AND THE NATURE OF THE CHANGE SHOULD BE NOTED UNDER REMARKS. THESE REMARKS ARE NOT A PART OF THE DATA. THE REVISED DATA SHEET(S) BE COME PART OF THE ORIGINAL DATA AND SHALL BE COMPLIED WITH IN THEIR ENTIRETY.

ALL DATA SHEETS ATTACHED REVISED DATA SHEET(S) ONLY ATTACHED

REV. DATE BY CHECK APPROVALS REMARKS

SECTION PROJECT TOLEDO REFINERY

Toledo Refinery




Page 2 of 4


EQUIPMENT ID JOB NO. DOCUMENT NO REV.

SYMBOL * = MINIMUM INFORMATION TO BE FILLED-IN BY BUYER, OTHER ITEMS MAY BE SPECIFIED AT CUSTOMERS OPTION.

GENERAL SELECTION TOWER MODEL TYPE

DESIGN AND OPERATING CONDITIONS *CIRCULATING WATER FLOW, US GPM *HOT (INLET) WATER TEMP, F *COLD (OUTLET) WATER TEMP, F * WET BULB TEMP F, INLET AMBIENT TOWER PUMP HEAD, FT TOTAL FAN BHP, (DRIVER OUTPUT) DRIFT LOSS, % CIRCULATION FLOW EVAPORATION LOSS (AT DESIGN) * DESIGN WIND LOAD, LB/SQ FT MI/HR *DESIGN SEISMIC LOAD, % G *TOWER SITE (GROUND LEVEL, ROOF, ETC.) *ELEVATION ABOVE SEA LEVEL, FT *TOWER EXPOSURE *PREVAILING WIND

CLASSIFIED- HYDROCARBON PROCESS APPLICATION; UNCLASSIFIED - NON-HYDROCARBON, GENERAL PURPOSE STRUCTURAL DETAILS

NUMBER OF CELLS FANS PER CELL TOTAL NUMBER OF FANS *OVERALL TOWER DIM, L X W , FT. FAN STACK HEIGHT, FT OVERALL TOWER HEIGHT, FT INSIDE BASIN DIMENSIONS, FT *COLUMN EXTENSIONS PERIMETER, BELOW BASIN CURB, FT INTERNAL, BELOW CURB, FT (MAX) ANCHORAGE HOT WATER INLET - NUMBER NOMINAL DIAMETER, IN DESCRIPTION HT INLET ABOVE BASIN CURB, FT *ACCESS TO TOP OF TOWER SHIPPING WEIGHT, LBS OPERATING WEIGHT, LBS

MATERIALS OF CONSTRUCTION FRAME WORK MEMBERS CASING FILLING SUPPORT DRIFT ELIMINATORS SPACER FAN STACKS LOUVERS, MATERIAL

Toledo Refinery




Page 3 of 4



MATERIALS OF CONSTRUCTION (CONTINUED) PARTITIONS FAN DECK WATER DISTRIBUTION - TYPE MATERIAL LUMBER PRETREATMENT TYPE OF TREATMENT ITEMS TREATED SPLASHERS OR SPRAY NOZZLES STAIRWAY AND HANDRAIL LADDER STRUCTURAL CONNECTIONS BOLTS, NUTS, WASHERS ANCHOR CONNECTIONS NAILS MECHANICAL EQUIPMENT *ANCHOR BOLTS- MATERIAL FURNISHED BY *COLD WATER BASIN- MATERIAL FURNISHED BY BASIN ACCESSORIES, BY MFR

MECHANICAL EQUIPMENT FANS NUMBER TYPE OR MODEL MANUFACTURER DIAMETER, FT

NUMBER OF BLADES FAN SPEED, RPM TIP SPEED, RPM BHP/FAN, DRIVER OUTPUT BLADE MATERIAL HUB MATERIAL TOTAL STATIC PRESSURE, IN. WTR VELOCITY PRESSURE, IN. WTR AIR DELIVERY/FAN, ACFM FAN STATIC EFFICIENCY

SPEED REDUCER NUMBER TYPE --MODEL --MANUFACTURER --REDUCTION RATIO AGMA MECH HP RATING

SERVICE FACTOR RATE HP NO. OF REDUCTIONS

Toledo Refinery




Page 4 of 4



MECHANICAL EQUIPMENT (CONTINUED) DRIVE SHAFT NUMBER TYPE - MODEL MANUFACTURER RATED HP DRIVE SHAFT MATERIAL COUPLING TYPE, MATERIAL

DRIVER NUMBER *KIND *TYPE MANUFACTURER FULL LOAD SPEED, RPM *ELECTRICAL CHARACTERISTICS PHASE HZ VOLTS RATED HP

ADDITIONAL DATA

NUMERICAL INDEXSECTION 8 TABLE OF CONTENTSEP 8-4-1EP 8-4-1C

8_4_1ds

Documents