8mm FRAMELESS

DOOR GUIDE

SLIDING

1

General InformationPlease inspect this product upon delivery. Any missing parts or manufacturingdefects must be reported immediately to the supplier. Damage or defectsreported later will not be accepted. TAKE CARE WHEN HANDLING GLASSPARTS-AVOID HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANYHARD SURFACE. Glass breakage claims will not be accepted after the producthas been unpacked.

This product is heavy and may require two people to install.

TOOLS REQUIRED

Ø3mm Drill bit

Ø6mm Drill bit

Pencil

Spirit level

Tape measure

DESCRIPTION DESCRIPTIONPART IMAGE PART IMAGE

Drill

Flat-headScrewdriver

Cross headScrewdriver

Mallet

Silicone Sealant

PZ1

2

ASSEMBLY INSTRUCTIONS - DRAWING

(1) 1x Guide Rail Seal(2) 1x Door Stop Cap(3) 1x Cover Cap (Guide Rail)(4) 1x Wall Post Cover Cap A(5) 1x Guide Rail(6) 10x Wall Plugs (7) 10x Screws 4x30(8) 1x Wall Profile A(9) 1x Wedge Gasket Seal(10) 1x Fixed Panel(11) 2x Fixed Panel Seal(12) 1x Handle

(13) 2 Bottom Guide Blocks Part B (L+R) x

(14) 1 Bottom Guide Blocks Part A x (15) 1x Drip Strip

(17) 2x Drip Strip End Cap (L+R)(18) 1x Wall Profile B

(16) 1x Moving Panel

(19) 1x Wall Fixing Seat(20) 1x Adjustment Bracket(21) 4x Bump Stops(22) 2x Rollers(23) 2x Screw Caps(24) 2x Screws(25) 2x Glass-Fitting Parts

(10)

(8)

(7)

(5)(4)(3)

(2)

(1)

(6)

(9)

(11)

(12)

(13)(14)(15) (16)(17)(18)

(20)(21)(22)(23)(24)(25)(19)

Step 2

6mm x4

x44x30

x4

x4

10mm

SLIDING DOOR RECESS INSTALLATION

3

Step 1 DRILLING WALL PROFILE TO THE WALL

Please ensure that the shower tray is level and checked with a spirit level.The tray should be installed first. Tiles should then be tiled down to the tray.The enclosure can then be installed.

Before Installation

1

2 3

4 5

1

2

Step 3

Step 4

x2

x2

4

1

2

1

2

3

4

5

Step 5

Step 6

5

Ø6mm

x21 2

3 4

x2

x2

x2

1

2

3

4

MAX:20mm

MAX:20mm

5

6

7

Step 7

Step 8

6

H2Oinside

1

2

1

2

3

4

5

6

7

Step 9

x2

x2

x2

View from inside

Step 10

Adjust

7

1

2

3

4

5

6

1

2

3

4

Step 11

OUTSIDE

OUTSIDE

4x30

x4

x4

6mm

x4

x4 x4

Step 12

8

1

2

3

4

5

6

7

Step 14

Step 13

8mm glass

Allow 24 hours for silicone to

dry before use. Silicone on the

outside edge only, NOT THE INSIDE

9

INSIDE

1

2

3

4

Aftercare instructionsRegularly clean your shower product with warm soapy water to prevent lime scalebuild up. DO NOT use abrasive cleaning fluids or materials, or strong chemical cleaners as this will damage the product surface.

Check out our full range of Shower Enclosures Quadrant Shower Enclosures

Corner Entry Shower Enclosures

Walk in Shower Enclosures

Sliding Shower Doors

Bifold Shower Doors

Pivot Shower Doors

Hinged Shower Doors

Shower Screens

From Top Brands Coram Shower Enclosures

Mira Shower Enclosures

Hydrolux Shower Enclosures

Diamond Shower Enclosures

With quality shower trays to match your enclosure Square Shower Trays

Rectangular Shower Trays

Quadrant Shower Trays

Coram Shower Trays

Mira Flight Shower Trays