92-23577-106 rev. 02 rlkl-b 7.5 thru 12.5 ton package air ... paquete solo frio... · package air...
TRANSCRIPT
PACKAGE AIR CONDITIONERS FEATURING INDUSTRY STANDARDR410A REFRIGERANTRLKL-B SERIES 7.5, 10 AND 12.5 TON [26.4, 35.2 AND 44.0 kW]60 HZ MODELS
92-23577-106-02SUPERSEDES 92-23577-106-01[ ] Designates Metric Conversions
THESE INSTRUCTIONS ARE INTENDED AS AN AID TO QUALI-FIED, LICENSED SERVICE PERSONNEL FOR PROPER INSTALLA-TION, ADJUSTMENT AND OPERATION OF THIS UNIT. READTHESE INSTRUCTIONS THOROUGHLY BEFORE ATTEMPTINGINSTALLATION OR OPERATION. FAILURE TO FOLLOW THESEINSTRUCTIONS MAY RESULT IN IMPROPER INSTALLATION,ADJUSTMENT, SERVICE OR MAINTENANCE POSSIBLY RESULT-ING IN FIRE, ELECTRICAL SHOCK, PROPERTY DAMAGE, PER-SONAL INJURY OR DEATH.
WARNING!
DO NOT DESTROYPLEASE READ CAREFULLY AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.
INSTALLATION INSTRUCTIONS
Recognize this symbol as an indication of Important Safety Information!!
ISO 9001:2008
TABLE OF CONTENTSI. Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3II. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4III. Checking Product Received . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4IV. Equipment Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4V. Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
A. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4B. Major Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5C. R-410A Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Unit Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8General Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-17
VI. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18A. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
1. Pre-Installation Check Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182. Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
B. Outside Slab Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18C. Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19D. Rooftop Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
VII. Ductwork . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20VIII. Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21IX. Conversion Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21X. Condensate Drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21XI. Electrical Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
A. Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22B. Control Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23C. Internal Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23D. Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23E. Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
XII. Indoor Air Flow Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24XIII. Crankcase Heat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24XIV. Pre-Start Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24XV. Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25XVI. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26XVII. Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Airflow Data Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27-29XVIII. Heater Kit Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-35XIX. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36XX. Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-40XXI. Charge Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41-43
2
! WARNINGTHE MANUFACTURER’S WARRANTY DOES NOT COVER ANY DAMAGE ORDEFECT TO THE AIR CONDITIONER CAUSED BY THE ATTACHMENT OR USEOF ANY COMPONENTS, ACCESSORIES OR DEVICES (OTHER THAN THOSEAUTHORIZED BY THE MANUFACTURER) INTO, ONTO OR IN CONJUNCTIONWITH THE AIR CONDITIONER. YOU SHOULD BE AWARE THAT THE USE OFUNAUTHORIZED COMPONENTS, ACCESSORIES OR DEVICES MAY ADVERSE-LY AFFECT THE OPERATION OF THE AIR CONDITIONER AND MAY ALSOENDANGER LIFE AND PROPERTY. THE MANUFACTURER DISCLAIMS ANYRESPONSIBILITY FOR SUCH LOSS OR INJURY RESULTING FROM THE USEOF SUCH UNAUTHORIZED COMPONENTS, ACCESSORIES OR DEVICES.
! WARNINGDISCONNECT ALL POWER TO THE UNIT BEFORE STARTING MAINTENANCE.FAILURE TO DO SO CAN RESULT IN SEVERE ELECTRICAL SHOCK ORDEATH.
! CAUTIONR-410A systems operate at higher pressures than R-22 systems. Do not use R-22service equipment or components on R-410A equipment.
! WARNINGDO NOT, UNDER ANY CIRCUMSTANCES, CONNECT RETURN DUCTWORK TOANY OTHER HEAT PRODUCING DEVICE SUCH AS A FIREPLACE INSERT,STOVE, ETC. UNAUTHORIZED USE OF SUCH DEVICES MAY RESULT IN FIRE,CARBON MONOXIDE POISONING, EXPLOSION, PROPERTY DAMAGE,SEVERE PERSONAL INJURY OR DEATH.
! WARNINGTHE UNIT MUST BE PERMANENTLY GROUNDED. A GROUNDING LUG ISPROVIDED IN THE ELECTRIC HEAT ACCESS AREA FOR A GROUND WIRE.FAILURE TO GROUND THIS UNIT CAN RESULT IN FIRE OR ELECTRICALSHOCK CAUSING PROPERTY DAMAGE, SEVERE PERSONAL INJURY ORDEATH.
! WARNINGONLY ELECTRIC HEATER KITS SUPPLIED BY THIS MANUFACTURER ASDESCRIBED IN THIS PUBLICATION HAVE BEEN DESIGNED, TESTED, ANDEVALUATED FOR USE WITH THIS UNIT. USE OF ANY OTHER MANUFAC-TURED ELECTRIC HEATERS INSTALLED WITHIN THIS UNIT MAY CAUSEHAZARDOUS CONDITIONS RESULTING IN PROPERTY DAMAGE, FIRE, BODI-LY INJURY OR DEATH.
I. SAFETY INFORMATION
3
II. INTRODUCTIONThis booklet contains the installation and operating instructions for your air conditioner.There are a few precautions that should be taken to derive maximum satisfaction from it.Improper installation can result in unsatisfactory operation or dangerous conditions.
Read this booklet and any instructions packaged with separate equipment required tomake up the system prior to installation. Give this booklet to the owner and explain itsprovisions. The owner should retain this booklet for future reference.
III. CHECKING PRODUCT RECEIVEDUpon receiving the unit, inspect it for any damage from shipment. Claims for damage,either shipping or concealed, should be filed immediately with the shipping company.Check the unit model number, heating size, electrical characteristics, and accessories todetermine if they are correct.
IV. EQUIPMENT PROTECTION FROM THEIV. ENVIRONMENTThe metal parts of this unit may be subject to rust or deterioration in adverse environ-mental conditions. This oxidation could shorten the equipment’s useful life. Salt spray,fog or mist in seacoast areas, sulphur or chlorine from lawn watering systems, and vari-ous chemical contaminants from industries such as paper mills and petroleum refineriesare especially corrosive.
If the unit is to be installed in an area where contaminants are likely to be a prob-lem, special attention should be given to the equipment location and exposure.
1. Avoid having lawn sprinkler heads spray direction on the unit cabinet.
2. In coastal areas, locate the unit on the side of the building away from the waterfront.
3. Shielding provided by a fence or shrubs may give some protection.
Regular maintenance will reduce the buildup of contaminants and help to protectthe unit’s finish.
1. Frequent washing of the cabinet, fan blade and coil with fresh water will removemost of the salt or other contaminants that build up on the unit.
2. Regular cleaning and waxing of the cabinet with a good automobile polish will pro-vide some protection.
3. A good liquid cleaner may be used several times a year to remove matter that willnot wash off with water.
Several different types of protective coatings are offered in some areas. These coatingsmay provide some benefit, but the effectiveness of such coating materials cannot be ver-ified by the equipment manufacturer.
The best protection is frequent cleaning, maintenance and minimal exposure tocontaminants.
V. SPECIFICATIONSA. GENERALThe Packaged Air Conditioners are available without heat or with 10, 15, 20, 30, 40 or50 kW electric heat. Cooling capacities of 7.5, 10 or 12.5 nominal tons of cooling areavailable. Units are convertible from horizontal supply and return to bottom supply andreturn by relocation of supply and return air access panels. See cover installation detail.
The units are weatherized for mounting outside of the building.
! WARNINGTHE MANUFACTURER’S WARRAN-TY DOES NOT COVER ANY DAM-AGE OR DEFECT TO THE AIR CON-DITIONER CAUSED BY THEATTACHMENT OR USE OF ANYCOMPONENTS, ACCESSORIES ORDEVICES (OTHER THAN THOSEAUTHORIZED BY THE MANUFAC-TURER) INTO, ONTO OR IN CON-JUNCTION WITH THE AIR CONDI-TIONER. YOU SHOULD BE AWARETHAT THE USE OF UNAUTHO-RIZED COMPONENTS, ACCES-SORIES OR DEVICES MAYADVERSELY AFFECT THE OPERA-TION OF THE AIR CONDITIONERAND MAY ALSO ENDANGER LIFEAND PROPERTY. THE MANUFAC-TURER DISCLAIMS ANY RESPON-SIBILITY FOR SUCH LOSS ORINJURY RESULTING FROM THEUSE OF SUCH UNAUTHORIZEDCOMPONENTS, ACCESSORIES ORDEVICES.
4
! WARNINGDISCONNECT ALL POWER TO THE UNIT BEFORE STARTING MAINTENANCE.FAILURE TO DO SO CAN RESULT IN SEVERE ELECTRICAL SHOCK ORDEATH.
The information on the rating plate is in compliance with the FTC and DOE rating for sin-gle phase units. The following information is for three phase units which are not coveredunder the DOE certification program.
1. The efficiency rating of this unit is a product thermal efficiency rating determinedunder continuous operating conditions independent of any installed system.
B. MAJOR COMPONENTSThe typical unit includes a hermetically-sealed refrigerating system (consisting of a com-pressor, condenser coil, evaporator coil with thermal expansion valve), a circulation airblower, a condenser fan, and all necessary internal electrical wiring. The cooling systemof these units are factory-evacuated, charged and performance tested. Refrigerantamount and type are indicated on rating plate.
C. R-410A REFRIGERANTAll units are factory charged with R-410A refrigerant.
1. Specification of R-410A:
Application: R-410A is not a drop-in replacement for R-22; equipment designs mustaccommodate its higher pressures. It cannot be retrofitted into R-22 units.
Pressure: The pressure of R-410A is approximately 60% (1.6 times) greater thanR-22. Recovery and recycle equipment, pumps, hoses and the like need to have designpressure ratings appropriate for R-410A. Manifold sets need to range up to 800 psighigh-side and 250 psig low-side with a 550 psig low-side retard. Hoses need to have aservice pressure rating of 800 psig. Recovery cylinders need to have a 400 psig servicepressure rating. DOT 4BA400 or DOT BW400.
Combustibility: At pressures above 1 atmosphere, mixture of R-410A and air canbecome combustible. R-410A and air should never be mixed in tanks or supplylines, or be allowed to accumulate in storage tanks. Leak checking should neverbe done with a mixture of R-410A and air. Leak checking can be performed safelywith nitrogen or a mixture of R-410A and nitrogen.
2. Quick Reference Guide For R-410A
• R-410A refrigerant operates at approximately 60% higher pressure (1.6 times) than R-22. Ensure that servicing equipment is designed to operate with R-410A.
• R-410A refrigerant cylinders are pink.• R-410A, as with other HFC’s is only compatible with POE oils.• Vacuum pumps will not remove moisture from POE oil.• R-410A systems are to be charged with liquid refrigerants. Prior to March 1999, R-410A refrigerant cylinders had a dip tube. These cylinders should be kept upright forequipment charging. Post March 1999 cylinders do not have a dip tube and shouldbe inverted to ensure liquid charging of the equipment.
• Do not install a suction line filter drier in the liquid line.• A liquid line filter drier is standard on every unit.• Desiccant (drying agent) must be compatible for POE oils and R-410A.
3. Evaporator Coil / Expansion Device
The expansion device is specifically designed to operate with R-410A. DO NOT use anR-22 device. The existing evaporator must be replaced with the factory specifiedevaporator specifically designed for R-410A.
4. Tools Required For Installing & Servicing R-410A Models
Manifold Sets:-Up to 800 PSIG High side-Up to 250 PSIG Low Side-550 PSIG Low Side Retard
Manifold Hoses:-Service Pressure Rating of 800 PSIG
Recovery Cylinders:-400 PSIG Pressure Rating-Dept. of Transportation 4BA400 or BW400
5
! CAUTIONR-410A systems operate at higher pressures than R-22 systems. Do not use R-22service equipment or components on R-410A equipment.
RETURN COVER
CONDENSER FANS
FRONT SIDE
LEFT SIDE
SUPPLY COVER(REAR SIDE)
COMPRESSORACCESS
FIGURE 1UNIT DIMENSIONS AND ACCESS LOCATIONS
FIGURE 2BASE DIMENSIONS
ST-A1112-02-00
ST-A1154-03-00
403⁄16”[1020.7 mm]
313⁄16”[96.8 mm]
5”[127 mm]
1111⁄16”[296.9 mm]
41⁄8”[104.8 mm]
65⁄8”[168.3 mm]
613⁄16”[173 mm]
583⁄4”[1492.2 mm]
POWERENTRY
13⁄4” [44.5 mm]DIA.
CONTROLENTRY
7⁄8” [22.2 mm]DIA.
9311⁄16”[2379.6 mm]
6
ELECTRICALACCESS
BLOWERACCESS
COMPRESSORACCESS
CONDENSERCOIL
(RIGHT SIDE)
SUPPLYAIR
RETURNAIR
REARSIDE
FIGURE 3UNIT DIMENSIONS
ST-A1154-04-00
SUPPLY RETURN DIMENSIONS FOR DOWNFLOW APPLICATIONS
25"[635 mm]
14"[355.6 mm]
34"[863.6 mm]
8"[203.2 mm]
THRU THE BASE ELECTRIC
54"[1371.6 mm]
23"[585.5 mm]
FIGURE 4BOTTOM VIEW
A0712-02
9311/16”[2379.4 mm]
47/16”[112.7 mm]
21/16”
151/8”[384.1 mm]
47/16”[112.7 mm]
107/16”[265.1 mm]
21/8”[54 mm]
61/2”[165.1 mm]
271/2”[698.5 mm]
21/8”[54 mm]
8815/16”[2259 mm]
23/8”[60.3 mm]
583/4”[1492.2 mm]
RIGHTSIDE
FRONTSIDE
7
SUPPLY AND RETURN DIMENSIONS FOR DOWNFLOW APPLICATIONS
LEFTSIDE
*26"[660.4 mm]
12"[304.8 mm]
44"[1117.6 mm]
34"[863.6 mm]
14"[355.6 mm]
28"[711.2 mm]
SUPPLY AND RETURN DIMENSIONS FOR HORIZONTAL APPLICATION
SUPPLY DUCT MAY EXTEND UP TO THIS LEVEL
FIGURE 5REAR VIEW
A0714-03*RECOMMENDED DUCT DIMENSIONS ARE 26”
9311/16”[2379.6 mm]
135/8”[346 mm]
47/16”[112.7 mm]
77/32”[183.3 mm]
8
LEFTSIDE
RIGHTSIDE
COMPRESSORACCESS
9
GENERAL DATA - RLKL
NOM. SIZE 7.5, 10 AND 12.5 TON [26.4, 35.2 AND 44.0 kW]
Model RLKL - Series B090CL B090CM B090CN B090DL
Cooling performance1
Gross Cooling Capacity Btu [kW] 87,000 [25.49] 87,000 [25.49] 87,000 [25.49] 87,000 [25.49]EER/SEER2 11.2/NA 11.2/NA 11.2/NA 11.2/NANominal CFM/AHRI Rated CFM [L/s] 2800/2925 [1321/1380] 2800/2925 [1321/1380] 2800/2925 [1321/1380] 2800/2925 [1321/1380]AHRI Net Cooling Capacity Btu [kW] 84,000 [24.61] 84,000 [24.61] 84,000 [24.61] 84,000 [24.61]Net Sensible Capacity Btu [kW] 64,800 [18.99] 64,800 [18.99] 64,800 [18.99] 64,800 [18.99]Net Latent Capacity Btu [kW] 19,200 [5.63] 19,200 [5.63] 19,200 [5.63] 19,200 [5.63]IEER3 12.1 12.1 12.1 12.1Net System Power kW 7.5 7.5 7.5 7.5
CompressorNo./Type 1/Scroll 1/Scroll 1/Scroll 1/Scroll
Outdoor Sound Rating (dB)5 88 88 88 88
Outdoor Coil - Fin Type Louvered Louvered Louvered LouveredTube Type MicroChannel MicroChannel MicroChannel MicroChannelMicroChannel Depth in. [mm] 1 [25.4] 1 [25.4] 1 [25.4] 1 [25.4]Face Area sq. ft. [sq. m] 13.5 [1.25] 13.5 [1.25] 13.5 [1.25] 13.5 [1.25]Rows / FPI [FPcm] 1 / 23 [9] 1 / 23 [9] 1 / 23 [9] 1 / 23 [9]
Indoor Coil - Fin Type Louvered Louvered Louvered LouveredTube Type Rifled Rifled Rifled RifledTube Size in. [mm] 0.375 [9.5] 0.375 [9.5] 0.375 [9.5] 0.375 [9.5]Face Area sq. ft. [sq. m] 13.5 [1.25] 13.5 [1.25] 13.5 [1.25] 13.5 [1.25]Rows / FPI [FPcm] 2 / 18 [7] 2 / 18 [7] 2 / 18 [7] 2 / 18 [7]Refrigerant Control Orifices Orifices Orifices OrificesDrain Connection No./Size in. [mm] 1/1 [25.4] 1/1 [25.4] 1/1 [25.4] 1/1 [25.4]
Outdoor Fan - Type Propeller Propeller Propeller PropellerNo. Used/Diameter in. [mm] 1/24 [609.6] 1/24 [609.6] 1/24 [609.6] 1/24 [609.6]Drive Type/No. Speeds Direct/1 Direct/1 Direct/1 Direct/1CFM [L/s] 4500 [2124] 4500 [2124] 4500 [2124] 4500 [2124]No. Motors/HP 1 at 1/2 HP 1 at 1/2 HP 1 at 1/2 HP 1 at 1/2 HPMotor RPM 1075 1075 1075 1075
Indoor Fan - Type FC Centrifugal FC Centrifugal FC Centrifugal FC CentrifugalNo. Used/Diameter in. [mm] 1/15x15 [381x381] 1/15x15 [381x381] 1/15x15 [381x381] 1/15x15 [381x381]Drive Type/No. Speeds Belt/Variable Belt/Variable Belt/Variable Belt/VariableNo. Motors 1 1 1 1Motor HP 2 2 3 2Motor RPM 1725 1725 1725 1725Motor Frame Size 56 56 56 56
Filter - Type Disposable Disposable Disposable DisposableFurnished Yes Yes Yes Yes(NO.) Size Recommended in. [mm x mm x mm] (6)2x18x18 [51x457x457] (6)2x18x18 [51x457x457] (6)2x18x18 [51x457x457] (6)2x18x18 [51x457x457]
Refrigerant Charge Oz. [g] 117.6 [3334] 117.6 [3334] 117.6 [3334] 117.6 [3334]
WeightsNet Weight lbs. [kg] 882 [401] 882 [401] 890 [404] 882 [401]Ship Weight lbs. [kg] 919 [417] 919 [417] 927 [420] 919 [417]
Continued ->
10
GENERAL DATA - RLKL
NOM. SIZE 7.5, 10 AND 12.5 TON [26.4, 35.2 AND 44.0 kW]
Model RLKL - Series B090DM B090DN B090YL B090YM
Cooling performance1
Gross Cooling Capacity Btu [kW] 87,000 [25.49] 87,000 [25.49] 87,000 [25.49] 87,000 [25.49]EER/SEER2 11.2/NA 11.2/NA 11.2/NA 11.2/NANominal CFM/AHRI Rated CFM [L/s] 2800/2925 [1321/1380] 2800/2925 [1321/1380] 2800/2925 [1321/1380] 2800/2925 [1321/1380]AHRI Net Cooling Capacity Btu [kW] 84,000 [24.61] 84,000 [24.61] 84,000 [24.61] 84,000 [24.61]Net Sensible Capacity Btu [kW] 64,800 [18.99] 64,800 [18.99] 64,800 [18.99] 64,800 [18.99]Net Latent Capacity Btu [kW] 19,200 [5.63] 19,200 [5.63] 19,200 [5.63] 19,200 [5.63]IEER3 12.1 12.1 12.1 12.1Net System Power kW 7.5 7.5 7.5 7.5
CompressorNo./Type 1/Scroll 1/Scroll 1/Scroll 1/Scroll
Outdoor Sound Rating (dB)5 88 88 88 88
Outdoor Coil - Fin Type Louvered Louvered Louvered LouveredTube Type MicroChannel MicroChannel MicroChannel MicroChannelMicroChannel Depth in. [mm] 1 [25.4] 1 [25.4] 1 [25.4] 1 [25.4]Face Area sq. ft. [sq. m] 13.5 [1.25] 13.5 [1.25] 13.5 [1.25] 13.5 [1.25]Rows / FPI [FPcm] 1 / 23 [9] 1 / 23 [9] 1 / 23 [9] 1 / 23 [9]
Indoor Coil - Fin Type Louvered Louvered Louvered LouveredTube Type Rifled Rifled Rifled RifledTube Size in. [mm] 0.375 [9.5] 0.375 [9.5] 0.375 [9.5] 0.375 [9.5]Face Area sq. ft. [sq. m] 13.5 [1.25] 13.5 [1.25] 13.5 [1.25] 13.5 [1.25]Rows / FPI [FPcm] 2 / 18 [7] 2 / 18 [7] 2 / 18 [7] 2 / 18 [7]Refrigerant Control Orifices Orifices Orifices OrificesDrain Connection No./Size in. [mm] 1/1 [25.4] 1/1 [25.4] 1/1 [25.4] 1/1 [25.4]
Outdoor Fan - Type Propeller Propeller Propeller PropellerNo. Used/Diameter in. [mm] 1/24 [609.6] 1/24 [609.6] 1/24 [609.6] 1/24 [609.6]Drive Type/No. Speeds Direct/1 Direct/1 Direct/1 Direct/1CFM [L/s] 4500 [2124] 4500 [2124] 4500 [2124] 4500 [2124]No. Motors/HP 1 at 1/2 HP 1 at 1/2 HP 1 at 1/2 HP 1 at 1/2 HPMotor RPM 1075 1075 1075 1075
Indoor Fan - Type FC Centrifugal FC Centrifugal FC Centrifugal FC CentrifugalNo. Used/Diameter in. [mm] 1/15x15 [381x381] 1/15x15 [381x381] 1/15x15 [381x381] 1/15x15 [381x381]Drive Type/No. Speeds Belt/Variable Belt/Variable Belt/Variable Belt/VariableNo. Motors 1 1 1 1Motor HP 2 3 2 2Motor RPM 1725 1725 1725 1725Motor Frame Size 56 56 56 56
Filter - Type Disposable Disposable Disposable DisposableFurnished Yes Yes Yes Yes(NO.) Size Recommended in. [mm x mm x mm] (6)2x18x18 [51x457x457] (6)2x18x18 [51x457x457] (6)2x18x18 [51x457x457] (6)2x18x18 [51x457x457]
Refrigerant Charge Oz. [g] 117.6 [3334] 117.6 [3334] 117.6 [3334] 117.6 [3334]
WeightsNet Weight lbs. [kg] 882 [401] 890 [404] 882 [401] 882 [401]Ship Weight lbs. [kg] 919 [417] 927 [420] 919 [417] 919 [417]
Continued ->
11
GENERAL DATA - RLKL
NOM. SIZE 7.5, 10 AND 12.5 TON [26.4, 35.2 AND 44.0 kW]
Model RLKL - Series B090YN B120CL B120CM B120DL
Cooling performance1
Gross Cooling Capacity Btu [kW] 87,000 [25.49] 123,000 [36.04] 123,000 [36.04] 123,000 [36.04]EER/SEER2 11.2/NA 11.2/NA 11.2/NA 11.2/NANominal CFM/AHRI Rated CFM [L/s] 2800/2925 [1321/1380] 4000/3600 [1888/1699] 4000/3600 [1888/1699] 4000/3600 [1888/1699]AHRI Net Cooling Capacity Btu [kW] 84,000 [24.61] 119,000 [34.87] 119,000 [34.87] 119,000 [34.87]Net Sensible Capacity Btu [kW] 64,800 [18.99] 87,200 [25.55] 87,200 [25.55] 87,200 [25.55]Net Latent Capacity Btu [kW] 19,200 [5.63] 31,800 [9.32] 31,800 [9.32] 31,800 [9.32]IEER3 12.1 12.2 12.2 12.2Net System Power kW 7.5 10.62 10.62 10.62
CompressorNo./Type 1/Scroll 1/Scroll 1/Scroll 1/Scroll
Outdoor Sound Rating (dB)5 88 88 88 88
Outdoor Coil - Fin Type Louvered Louvered Louvered LouveredTube Type MicroChannel MicroChannel MicroChannel MicroChannelMicroChannel Depth in. [mm] 1 [25.4] 1 [25.4] 1 [25.4] 1 [25.4]Face Area sq. ft. [sq. m] 13.5 [1.25] 27 [2.51] 27 [2.51] 27 [2.51]Rows / FPI [FPcm] 1 / 23 [9] 1 / 23 [9] 1 / 23 [9] 1 / 23 [9]
Indoor Coil - Fin Type Louvered Louvered Louvered LouveredTube Type Rifled Rifled Rifled RifledTube Size in. [mm] 0.375 [9.5] 0.375 [9.5] 0.375 [9.5] 0.375 [9.5]Face Area sq. ft. [sq. m] 13.5 [1.25] 13.5 [1.25] 13.5 [1.25] 13.5 [1.25]Rows / FPI [FPcm] 2 / 18 [7] 2 / 22 [9] 2 / 22 [9] 2 / 22 [9]Refrigerant Control Orifices Orifices Orifices OrificesDrain Connection No./Size in. [mm] 1/1 [25.4] 1/1 [25.4] 1/1 [25.4] 1/1 [25.4]
Outdoor Fan - Type Propeller Propeller Propeller PropellerNo. Used/Diameter in. [mm] 1/24 [609.6] 2/24 [609.6] 2/24 [609.6] 2/24 [609.6]Drive Type/No. Speeds Direct/1 Direct/1 Direct/1 Direct/1CFM [L/s] 4500 [2124] 8400 [3964] 8400 [3964] 8400 [3964]No. Motors/HP 1 at 1/2 HP 1 at 1/3 HP 1 at 1/3 HP 1 at 1/3 HPMotor RPM 1075 1075 1075 1075
Indoor Fan - Type FC Centrifugal FC Centrifugal FC Centrifugal FC CentrifugalNo. Used/Diameter in. [mm] 1/15x15 [381x381] 1/15x15 [381x381] 1/15x15 [381x381] 1/15x15 [381x381]Drive Type/No. Speeds Belt/Variable Belt/Variable Belt/Variable Belt/VariableNo. Motors 1 1 1 1Motor HP 3 2 3 2Motor RPM 1725 1725 1725 1725Motor Frame Size 56 56 56 56
Filter - Type Disposable Disposable Disposable DisposableFurnished Yes Yes Yes Yes(NO.) Size Recommended in. [mm x mm x mm] (6)2x18x18 [51x457x457] (6)2x18x18 [51x457x457] (6)2x18x18 [51x457x457] (6)2x18x18 [51x457x457]
Refrigerant Charge Oz. [g] 117.6 [3334] 203.2 [5761] 203.2 [5761] 203.2 [5761]
WeightsNet Weight lbs. [kg] 890 [404] 984 [446] 992 [450] 984 [446]Ship Weight lbs. [kg] 927 [420] 1021 [463] 1029 [467] 1021 [463]
Continued ->
12
GENERAL DATA - RLKL
NOM. SIZE 7.5, 10 AND 12.5 TON [26.4, 35.2 AND 44.0 kW]
Model RLKL - Series B120DM B120YL B120YM B151CL
Cooling performance1
Gross Cooling Capacity Btu [kW] 123,000 [36.04] 123,000 [36.04] 123,000 [36.04] 146,000 [42.78]EER/SEER2 11.2/NA 11.2/NA 11.2/NA 11/NANominal CFM/AHRI Rated CFM [L/s] 4000/3600 [1888/1699] 4000/3600 [1888/1699] 4000/3600 [1888/1699] 5000/4225 [2360/1994]AHRI Net Cooling Capacity Btu [kW] 119,000 [34.87] 119,000 [34.87] 119,000 [34.87] 140,000 [41.02]Net Sensible Capacity Btu [kW] 87,200 [25.55] 87,200 [25.55] 87,200 [25.55] 99,500 [29.15]Net Latent Capacity Btu [kW] 31,800 [9.32] 31,800 [9.32] 31,800 [9.32] 40,500 [11.87]IEER3 12.2 12.2 12.2 10.8Net System Power kW 10.62 10.62 10.62 12.73
CompressorNo./Type 1/Scroll 1/Scroll 1/Scroll 2/Scroll
Outdoor Sound Rating (dB)5 88 88 88 88
Outdoor Coil - Fin Type Louvered Louvered Louvered LouveredTube Type MicroChannel MicroChannel MicroChannel MicroChannelMicroChannel Depth in. [mm] 1 [25.4] 1 [25.4] 1 [25.4] 1 [25.4]Face Area sq. ft. [sq. m] 27 [2.51] 27 [2.51] 27 [2.51] 27 [2.51]Rows / FPI [FPcm] 1 / 23 [9] 1 / 23 [9] 1 / 23 [9] 2 / 23 [9]
Indoor Coil - Fin Type Louvered Louvered Louvered LouveredTube Type Rifled Rifled Rifled RifledTube Size in. [mm] 0.375 [9.5] 0.375 [9.5] 0.375 [9.5] 0.375 [9.5]Face Area sq. ft. [sq. m] 13.5 [1.25] 13.5 [1.25] 13.5 [1.25] 13.5 [1.25]Rows / FPI [FPcm] 2 / 22 [9] 2 / 22 [9] 2 / 22 [9] 4 / 15 [6]Refrigerant Control Orifices Orifices Orifices TX ValvesDrain Connection No./Size in. [mm] 1/1 [25.4] 1/1 [25.4] 1/1 [25.4] 1/1 [25.4]
Outdoor Fan - Type Propeller Propeller Propeller PropellerNo. Used/Diameter in. [mm] 2/24 [609.6] 2/24 [609.6] 2/24 [609.6] 2/24 [609.6]Drive Type/No. Speeds Direct/1 Direct/1 Direct/1 Direct/1CFM [L/s] 8400 [3964] 8400 [3964] 8400 [3964] 8000 [3775]No. Motors/HP 1 at 1/3 HP 1 at 1/3 HP 1 at 1/3 HP 2 at 1/2 HPMotor RPM 1075 1075 1075 1075
Indoor Fan - Type FC Centrifugal FC Centrifugal FC Centrifugal FC CentrifugalNo. Used/Diameter in. [mm] 1/15x15 [381x381] 1/15x15 [381x381] 1/15x15 [381x381] 1/15x15 [381x381]Drive Type Belt/Variable Belt/Variable Belt/Variable Belt (Adjustable)No. Speeds SingleNo. Motors 1 1 1 1Motor HP 3 2 3 3Motor RPM 1725 1725 1725 1725Motor Frame Size 56 56 56 56
Filter - Type Disposable Disposable Disposable DisposableFurnished Yes Yes Yes Yes(NO.) Size Recommended in. [mm x mm x mm] (6)2x18x18 [51x457x457] (6)2x18x18 [51x457x457] (6)2x18x18 [51x457x457] (6)2x18x18 [51x457x457]
Refrigerant Charge Oz. (Sys. 1/Sys. 2) [g] 203.2 [5761] 203.2 [5761] 203.2 [5761] 147.2/152 [4173/4309]
WeightsNet Weight lbs. [kg] 992 [450] 984 [446] 992 [450] 1230 [558]Ship Weight lbs. [kg] 1029 [467] 1021 [463] 1029 [467] 1267 [575]
Continued ->
13
GENERAL DATA - RLKL
NOM. SIZE 7.5, 10 AND 12.5 TON [26.4, 35.2 AND 44.0 kW]
Model RLKL - Series B151CM B151DL B151DM B151YL
Cooling performance1
Gross Cooling Capacity Btu [kW] 146,000 [42.78] 146,000 [42.78] 146,000 [42.78] 146,000 [42.78]EER/SEER2 11/NA 11/NA 11/NA 11/NANominal CFM/AHRI Rated CFM [L/s] 5000/4225 [2360/1994] 5000/4225 [2360/1994] 5000/4225 [2360/1994] 5000/4225 [2360/1994]AHRI Net Cooling Capacity Btu [kW] 140,000 [41.02] 140,000 [41.02] 140,000 [41.02] 140,000 [41.02]Net Sensible Capacity Btu [kW] 99,500 [29.15] 99,500 [29.15] 99,500 [29.15] 99,500 [29.15]Net Latent Capacity Btu [kW] 40,500 [11.87] 40,500 [11.87] 40,500 [11.87] 40,500 [11.87]IEER3 10.8 10.8 10.8 10.8Net System Power kW 12.73 12.73 12.73 12.73
CompressorNo./Type 2/Scroll 2/Scroll 2/Scroll 2/Scroll
Outdoor Sound Rating (dB)5 88 88 88 88
Outdoor Coil - Fin Type Louvered Louvered Louvered LouveredTube Type MicroChannel MicroChannel MicroChannel MicroChannelMicroChannel Depth in. [mm] 1 [25.4] 1 [25.4] 1 [25.4] 1 [25.4]Face Area sq. ft. [sq. m] 27 [2.51] 27 [2.51] 27 [2.51] 27 [2.51]Rows / FPI [FPcm] 2 / 23 [9] 2 / 23 [9] 2 / 23 [9] 2 / 23 [9]
Indoor Coil - Fin Type Louvered Louvered Louvered LouveredTube Type Rifled Rifled Rifled RifledTube Size in. [mm] 0.375 [9.5] 0.375 [9.5] 0.375 [9.5] 0.375 [9.5]Face Area sq. ft. [sq. m] 13.5 [1.25] 13.5 [1.25] 13.5 [1.25] 13.5 [1.25]Rows / FPI [FPcm] 4 / 15 [6] 4 / 15 [6] 4 / 15 [6] 4 / 15 [6]Refrigerant Control TX Valves TX Valves TX Valves TX ValvesDrain Connection No./Size in. [mm] 1/1 [25.4] 1/1 [25.4] 1/1 [25.4] 1/1 [25.4]
Outdoor Fan - Type Propeller Propeller Propeller PropellerNo. Used/Diameter in. [mm] 2/24 [609.6] 2/24 [609.6] 2/24 [609.6] 2/24 [609.6]Drive Type/No. Speeds Direct/1 Direct/1 Direct/1 Direct/1CFM [L/s] 8000 [3775] 8000 [3775] 8000 [3775] 8000 [3775]No. Motors/HP 2 at 1/2 HP 2 at 1/2 HP 2 at 1/2 HP 2 at 1/2 HPMotor RPM 1075 1075 1075 1075
Indoor Fan - Type FC Centrifugal FC Centrifugal FC Centrifugal FC CentrifugalNo. Used/Diameter in. [mm] 1/15x15 [381x381] 1/15x15 [381x381] 1/15x15 [381x381] 1/15x15 [381x381]Drive Type Belt (Adjustable) Belt (Adjustable) Belt (Adjustable) Belt (Adjustable)No. Speeds Single Single Single SingleNo. Motors 1 1 1 1Motor HP 5 3 5 3Motor RPM 1725 1725 1725 1725Motor Frame Size 184 56 184 56
Filter - Type Disposable Disposable Disposable DisposableFurnished Yes Yes Yes Yes(NO.) Size Recommended in. [mm x mm x mm] (6)2x18x18 [51x457x457] (6)2x18x18 [51x457x457] (6)2x18x18 [51x457x457] (6)2x18x18 [51x457x457]
Refrigerant Charge Oz. (Sys. 1/Sys. 2) [g] 147.2/152 [4173/4309] 147.2/152 [4173/4309] 147.2/152 [4173/4309] 147.2/152 [4173/4309]
WeightsNet Weight lbs. [kg] 1238 [562] 1230 [558] 1238 [562] 1230 [558]Ship Weight lbs. [kg] 1275 [578] 1267 [575] 1275 [578] 1267 [575]
Continued ->
14
GENERAL DATA - RLKL
NOM. SIZE 7.5, 10 AND 12.5 TON [26.4, 35.2 AND 44.0 kW]
Model RLKL - Series B151YM
Cooling performance1
Gross Cooling Capacity Btu [kW] 146,000 [42.78]EER/SEER2 11/NANominal CFM/AHRI Rated CFM [L/s] 5000/4225 [2360/1994]AHRI Net Cooling Capacity Btu [kW] 140,000 [41.02]Net Sensible Capacity Btu [kW] 99,500 [29.15]Net Latent Capacity Btu [kW] 40,500 [11.87]IEER3 10.8Net System Power kW 12.73
CompressorNo./Type 2/Scroll
Outdoor Sound Rating (dB)5 88
Outdoor Coil - Fin Type LouveredTube Type MicroChannelMicroChannel Depth in. [mm] 1 [25.4]Face Area sq. ft. [sq. m] 27 [2.51]Rows / FPI [FPcm] 2 / 23 [9]
Indoor Coil - Fin Type LouveredTube Type RifledTube Size in. [mm] 0.375 [9.5]Face Area sq. ft. [sq. m] 13.5 [1.25]Rows / FPI [FPcm] 4 / 15 [6]Refrigerant Control TX ValvesDrain Connection No./Size in. [mm] 1/1 [25.4]
Outdoor Fan - Type PropellerNo. Used/Diameter in. [mm] 2/24 [609.6]Drive Type/No. Speeds Direct/1CFM [L/s] 8000 [3775]No. Motors/HP 2 at 1/2 HPMotor RPM 1075
Indoor Fan - Type FC CentrifugalNo. Used/Diameter in. [mm] 1/15x15 [381x381]Drive Type Belt (Adjustable)No. Speeds SingleNo. Motors 1Motor HP 5Motor RPM 1725Motor Frame Size 184
Filter - Type DisposableFurnished Yes(NO.) Size Recommended in. [mm x mm x mm] (6)2x18x18 [51x457x457]
Refrigerant Charge Oz. (Sys. 1/Sys. 2) [g] 147.2/152 [4173/4309]
WeightsNet Weight lbs. [kg] 1238 [562]Ship Weight lbs. [kg] 1275 [578]
ELECTRICAL DATA - RLKL-B
15
187-253 187-253 187-253 414-506 414-506 414-506 518-632 518-632 518-632
208/230 208/230 208/230 460 460 460 575 575 575
40/40 40/40 45/45 20 20 23 15 15 19
50/50 50/50 60/60 25 25 30 20 20 25
60/60 60/60 60/60 30 30 30 20 20 25
1 1 1 1 1 1 1 1 1
200/240 200/240 200/240 480 480 480 600 600 600
3 3 3 3 3 3 3 3 3
3450 3450 3450 3450 3450 3450 3450 3450 3450
6 6 6 6 6 6 6 6 6
23.2/23.2 23.2/23.2 23.2/23.2 11.2 11.2 11.2 7.9 7.9 7.9
164/164 164/164 164/164 75 75 75 54 54 54
1 1 1 1 1 1 1 1 1
208/230 208/230 208/230 460 460 460 575 575 575
1 1 1 1 1 1 1 1 1
1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2
2.3/2.3 2.3/2.3 2.3/2.3 1.5 1.5 1.5 1 1 1
5.6/5.6 5.6/5.6 5.6/5.6 3.1 3.1 3.1 2.2 2.2 2.2
1 1 1 1 1 1 1 1 1
208/230 208/230 208/230 460 460 460 575 575 575
3 3 3 3 3 3 3 3 3
2 2 3 2 2 3 2 2 3
8/8 8/8 13/13 4 4 7 4 4 8
56/56 56/56 74.5/74.5 28 28 38.1 19 19 20
Unit Information
Com
pressor Motor
Condenser Motor
Evaporator Fan
ELECTRICAL DATA – RLKL SERIES
B090CL B090CM B090CN B090DL B090DM B090DN B090YL B090YM B090YN
Volts
Minimum CircuitAmpacity
Minimum OvercurrentProtection Device Size
Maximum OvercurrentProtection Device Size
No.
Volts
Phase
RPM
HP, Compressor 1
Amps (RLA), Comp. 1
Amps (LRA), Comp. 1
No.
Volts
Phase
HP
Amps (FLA, each)
Amps (LRA, each)
Phase
No.
HP
Amps (FLA, each)
Volts
Amps (LRA, each)
Unit Operating VoltageRange
16
ELECTRICAL DATA - RLKL-B
187-253 187-253 414-506 414-506 518-632 518-632
208/230 208/230 460 460 575 575
51/51 56/56 28 31 22 26
60/60 70/70 35 35 25 30
80/80 80/80 40 45 30 35
1 1 1 1 1 1
208/230 208/230 480 480 600 600
3 3 3 3 3 3
3450 3450 3450 3450 3450 3450
10 10 10 10 10 10
30.1/30.1 30.1/30.1 16.7 16.7 12.2 12.2
225/225 225/225 114 114 80 80
2 2 2 2 2 2
208/230 208/230 460 460 575 575
1 1 1 1 1 1
1/3 1/3 1/3 1/3 1/3 1/3
2.4/2.4 2.4/2.4 1.4 1.4 1 1
4.7/4.7 4.7/4.7 2.4 2.4 1.5 1.5
1 1 1 1 1 1
208/230 208/230 460 460 575 575
3 3 3 3 3 3
2 3 2 3 2 3
8/8 13/13 4 7 4 8
56/56 56/56 28 38.1 19 20
Unit Information
Com
pressor Motor
Condenser Motor
Evaporator Fan
ELECTRICAL DATA – RLKL SERIES
B120CL B120CM B120DL B120DM B120YL B120YM
Volts
Minimum CircuitAmpacity
Minimum OvercurrentProtection Device Size
Maximum OvercurrentProtection Device Size
No.
Volts
Phase
RPM
HP, Compressor 1
Amps (RLA), Comp. 1
Amps (LRA), Comp. 1
No.
Volts
Phase
HP
Amps (FLA, each)
Amps (LRA, each)
Phase
No.
HP
Amps (FLA, each)
Volts
Amps (LRA, each)
Unit Operating VoltageRange
17
ELECTRICAL DATA - RLKL-B
187-253 187-253 414-506 414-506 518-632 518-632
208/230 208/230 460 460 575 575
67/67 71/71 33 36 28 28
70/70 75/75 35 40 30 30
80/80 90/90 40 45 35 35
2 2 2 2 2 2
208/230 208/230 460 460 575 575
3 3 3 3 3 3
3450 3450 3450 3450 3450 3450
5 3/4 5 3/4 5 3/4 5 3/4 5 3/4 5 3/4
22.4/22.4 22.4/22.4 10.6 10.6 7.7 7.7
149/149 149/149 75 75 54 54
5 1/4 5 1/4 5 1/4 5 1/4 5 1/4 5 1/4
19/19 19/19 9.7 9.7 7.4 7.4
123/123 123/123 62 62 50 50
2 2 2 2 2 2
208/230 208/230 460 460 575 575
1 1 1 1 1 1
1/2 1/2 1/2 1/2 1/2 1/2
2.3/2.3 2.3/2.3 1.5 1.5 1 1
5.6/5.6 5.6/5.6 3.1 3.1 2.2 2.2
1 1 1 1 1 1
208/230 208/230 460 460 575 575
3 3 3 3 3 3
3 5 3 5 3 5
15/15 18.8/18.8 7 10 8 8
74.5/74.5 82.6/82.6 38.1 41.3 20 33
Unit Information
Com
pressor Motor
Condenser Motor
Evaporator Fan
ELECTRICAL DATA – RLKL SERIES
B151CL B151CM B151DL B151DM B151YL B151YM
Volts
Minimum CircuitAmpacity
Minimum OvercurrentProtection Device Size
Maximum OvercurrentProtection Device Size
No.
Volts
Phase
RPM
HP, Compressor 1
Amps (RLA), Comp. 1
Amps (LRA), Comp. 1
HP, Compressor 2
Amps (RLA), Comp. 2
Amps (LRA), Comp. 2
No.
Volts
Phase
HP
Amps (FLA, each)
Amps (LRA, each)
Phase
No.
HP
Amps (FLA, each)
Volts
Amps (LRA, each)
Unit Operating VoltageRange
18
VI. INSTALLATIONA. GENERAL
1. PRE-INSTALLATION CHECK-POINTS
Before attempting any installation, the following points should be carefully consid-ered:
a. Structural strength of supporting members.(rooftop installation)
b. Clearances and provision for servicing.
c. Power supply and wiring.
d. Air duct connections.
e. Drain facilities and connections.
f. Location for minimum noise.
2. LOCATION
These units are designed for outdoor installations. They can be mounted on aslab or rooftop. They are not to be installed within any part of a structure such asan attic, crawl space, closet, or any other place where condenser air flow isrestricted or other than outdoor ambient conditions prevail. Since the applicationof the units is of the outdoor type, it is important to consult your local code authori-ties at the time the first installation is made.
B. OUTSIDE SLAB INSTALLATION (Typical outdoor slab installations areshown in Figures 6 and 7.)1. Select a location where external water drainage cannot collect around the unit.
2. Provide a level concrete slab extending 3" [76.2 mm] beyond all four sides of theunit. The slab should be sufficient above grade to prevent ground water fromentering the unit. IMPORTANT: To prevent transmission of noise or vibration,slab should not be connected to building structure.
FIGURE 6OUTSIDE SLAB INSTALLATION, BASEMENT ORCRAWL SPACE DISTRIBUTION SYSTEM
A0741-03
RecommendedClearance Location
48” [1219.2 mm] A - Front
18” [457.2 mm] B - Condenser Coil
18” [457.2 mm] C - Duct Side
18”* [457.2 mm] D - Evaporator End
60” [1524 mm] E - Above
*Without Economizer. 48” [1219.2 mm] With*Economizer
FIGURE 7OUTSIDE SLAB INSTALLATION, CLOSET DISTRIBUTIONSYSTEM. SLAB FLOOR CONSTRUCTION
A0739-03
SUPPLY
DUCT
RETURN
DUCT
19
3. The location of the unit should be such as to provide proper access for inspectionand servicing.
4. Locate unit where operating sounds will not disturb owner or neighbors.5. Locate unit so roof runoff water does not pour directly on the unit. Provide gutteror other shielding at roof level. Do not locate unit in an area where excessivesnow drifting may occur or accumulate.
C. CLEARANCESThe following minimum clearances must be observed for proper unit performanceand serviceability.1. Provide 48" [1219.2 mm] minimum clearance at the front of the unit. Provide 18"[457.2 mm] minimum clearance at all other sides of the unit.
2. Provide 60" [1524 mm] minimum clearance between top of unit and maximum 3foot [.91 m] overhang.
3. Unit is design certified for application on combustible flooring with 0" [0 mm] mini-mum clearance.
4. See Figure 6 for illustration of minimum installation-service clearances.
D. ROOFTOP INSTALLATION1. Before locating the unit on the roof, make sure that the strength of the roof andbeams is adequate at that point to support the weight involved. This is veryimportant and user’s responsibility.
2. For rigging and roofcurb details, see Figures 8 and 9. Use field-furnished spread-ers.
3. For roofcurb assembly, see Roofcurb Installation Instructions.4. If the roofcurb is not used, provisions for disposing of condensate water runoffmust be provided.
5. The unit should be placed on a solid and level roofcurb or platform of adequatestrength. See Figure 10.
6. The location of the unit on the roof should be such as to provide proper access forinspection and servicing.
IMPORTANT: If unit will not be put into service immediately, cover supply and returnopenings to prevent excessive condensation.
FIGURE 8RIGGING FOR LIFTING
A B C D
10 [35.2] 33% 27% 17% 23%
7.5 [26.4] 30% 35% 14% 21%
12.5 [44.0] 44% 30% 12% 14%
A074403
10 TON
7.5 TON
12.5 TON[1000 mm]
A0744-03
CORNER WEIGHTS BY PERCENTAGECAPACITY TONS [kW]
20
VII. DUCTWORKDuctwork should be fabricated by the installing contractor in accordance with local codesand NFPA90A. Industry manuals may be used as a guide when sizing and designing theduct system - contact Air Conditioning Contractors of America, 1513 16th St. N.W.,Washington, D.C. 20036.
The unit should be placed as close to the space to be air conditioned as possible allow-ing clearance dimensions as indicated. Ducts should be run as directly as possible tosupply and return outlets. Use of non-flammable waterproof flexible connectors on bothsupply and return connections at the unit to reduce noise transmission is recommended.
It is preferable to install the unit on the roof of the structure if the registers or diffusersare located on the wall or in the ceiling. A slab installation could be considered when theregisters are low on a wall or in the floor.
On ductwork exposed to outside air conditions of temperature and humidity, use a mini-mum of 2" [50.8 mm] of insulation and a vapor barrier. Distribution system in attic, furredspace or crawl space should be insulated with at least 2" [50.8 mm] of insulation withvapor barrier. One-half to 1" [25.4 mm] thickness of insulation is usually sufficient forductwork inside the air conditioned space.
Balancing dampers should be provided for each branch duct in the supply system.Ductwork should be properly supported from the structure.
When installing ductwork, consider the following items:
! WARNINGDO NOT, UNDER ANY CIRCUMSTANCES, CONNECT RETURN DUCTWORK TOANY OTHER HEAT PRODUCING DEVICE SUCH AS A FIREPLACE INSERT,STOVE, ETC. UNAUTHORIZED USE OF SUCH DEVICES MAY RESULT IN FIRE,CARBON MONOXIDE POISONING, EXPLOSION, PROPERTY DAMAGE,SEVERE PERSONAL INJURY OR DEATH.
INSTALL GASKET
NAILING STRIP
DUCT FLANGE NOTTO EXCEED 1" [25.4 mm]
SUPPLY DUCT
RETURN DUCT
CAULK ALL JOINTSWATERTIGHT
ROOFCURB
UNIT
A0719-02
A0719-03
FIGURE 9ROOFCURB INSTALLATION
21
1. Noncombustible flexible connectors should be used between ductwork and unit toreduce noise and vibration transmission into the ductwork.
2. When auxiliary heaters are installed, use noncombustible flexible connectors andclearance to combustible material of 0" [0 mm] for the first 3 feet [.91 m] of dischargeduct. Clearance to unit top and side is 0" [0 mm].
VIII. FILTERSThis unit is provided with 6 - 2" x 18" x 18" [51mm x 457 mm x 457 mm] disposable fil-ters. When replacing filters, ensure they are inserted fully to the back to prevent bypass.
IX. CONVERSION PROCEDUREDOWNFLOW TO HORIZONTAL1. Remove the screws and covers from the outside of the supply and return sections.
2. Install the covers over the bottom supply and return openings, painted side up insert-ing the leading flange under the bracket provided. Place the back flange to the top ofthe front bracket provided. See Figure 11.
3. Secure the return and supply cover to the front bracket with one (1) screw.
X. CONDENSATE DRAINIMPORTANT: Install a condensate trap to ensure proper condensate drainage. SeeFigure 12.The condensate drain pan has a threaded female 1 inch NPT (11.5 TPI) connection.Consult local codes or ordinances for specific requirements of condensate drain pipingand disposal.• To use the removable drain pan feature of this unit, some of the condensate line jointsshould assembled for easy removal and cleaning.
• Use a thin layer of Teflon tape or paste on drain pan connections and install onlyhand tight.
• Do not over tighten drain pan connections as damage to the drain pan may occur.
FIGURE 10FLAT ROOFTOP INSTALLATION, ATTIC OR DROP CEILINGDISTRIBUTION SYSTEM. MOUNTED ON ROOFCURB. CURB MUST BE LEVEL
A1112-03
FIGURE 11COVER GASKET DETAIL
A0725-01
REAR PANEL
FRONT BRACKET
SUPPLY OR RETURN COVERINSULATION
BACKBRACKET
INSULATION
BASE PAN
BASE RAIL
NOTE: COVER SLIDESUNDER BACKBRACKET FLANGE.
NOTE: COVER FITS ONTOP OF FRONTBRACKET FLANGE.
22
• Drain line MUST NOT block service access panels.• Drain line must be no smaller than drain pan outlet and adequately sized to accom-modate the condensate discharge from the unit.
• Drain line should slope away from unit a minimum of 1/8” per foot to ensure properdrainage.
• Drain line must be routed to an acceptable drain or outdoors in accordance with localcodes.
• Do not connect condensate drain line to a closed sewer pipe.• Drain line may need insulation or freeze protection in certain applications.
XI. ELECTRICAL WIRINGField wiring must comply with the National Electrical Code (CEC in Canada) and local ordi-nances that may apply.
A. POWER WIRING1. This unit incorporates single-point electrical connections for the unit and electricheat accessory.
2. It is important that proper electrical power is available to the unit. Voltage should notvary more than 10% from the values marked on the unit rating plate. Phase volt-ages must be balanced within 3%.
3. Install a branch circuit disconnect within sight of the unit. Use the unit rating plate orRLNL-B Electrical Data to determine the required size.
4. The branch circuit wire must be sized in accordance with the National ElectricalCode (C.E.C. in Canada) and local ordinances that may apply using the minimumcircuit ampacity found on the unit rating plate.
5. Field-installed power wiring must be run through grounded rain-tight conduitattached to the unit power entry panel and connected as follows:UNITS WITHOUT ELECTRIC HEAT - Connect power wiring to the power terminalblock located on the left side of the electric heat compartment. Connect the groundwire to the adjacent ground lug.UNITS WITH FACTORY INSTALLED ELECTRIC HEAT - Connect power wiring tothe power terminal block located on the electric heater kit. Connect the ground wireto the adjacent ground lug. DO NOT connect aluminum wiring directly to the electricheater terminal block. Wiring to the unit contactors is factory-connected.
6. For field installation of an electric heater kit, follow the instructions below. Refer tothe information supplied with the kit.a. Removing screws as required, open heater access door and detach adjacentpower entry panel.
b. Remove wires to unit contactor (1L1, 1L2, 1L3) from unit terminal block on theleft side of the electric heat compartment. Remove and discard the terminal blockand the adjacent ground lug.
c. Remove the heater kit block-off panel and install the heater kit in its place using 9of the 12 screws previously removed.
d. Connect the unit contactor wires (1L1, 1L2, 1L3) to the compressor fuse block onthe heater kit.
e. Re-install the power entry panel & run conduit and the proper size field wiringthrough the opening in the panel.
FIGURE 12CONDENSATE DRAIN
3”[76 mm]
3”[76 mm]
23
f. Connect field wiring to the power terminal block located on the electric heaterkit. Connect ground wire to the adjacent ground lug.
g. Connect heater kit control plug to the receptacle on the control wiring harness.
h. Close heater access door and secure with screws previously removed.
B. CONTROL WIRING (Class II)1. Low voltage wiring should not be run in conduit with power wiring.
2. Control wiring is routed through the 7/8" [22 mm] hole in the unit side panel. SeeFigure 14. Use a minimum #18 AWG thermostat wire. For wire lengths exceeding50' [15.24 m] use #16 AWG thermostat wire. Connect the control wiring to the lowvoltage terminal block located on the unit integrated control. Route wires under thecontrol voltage shield. See Figure 14.
3. It is necessary that only approved thermostats be used. Please contact your distrib-utor for part number information. See thermostat specification catalog for recom-mended thermostat.
4. Figure 15 shows representative low voltage connection diagrams. Read your ther-mostat installation instructions for any special requirements for your specific thermo-stat.
C. INTERNAL WIRING1. A diagram of the internal wiring of this unit is located on the inside of the controlaccess panel and in this manual. If any of the original wiring must be replaced, thewire gauge and insulation must be the same as original wiring.Transformer is factory-wired for 230 volts on 208/230 volt models and must bechanged for 208-volt applications. See unit wiring diagram for 208-volt wiring.
D. GROUNDING
E. THERMOSTATThe thermostat should be mounted on an inside wall about five feet above the floor ina location where it will not be affected by unconditioned air, sun, or drafts from opendoors or other sources. READ installation instructions in air conditioner thermostatpackage CAREFULLY because each has some different wiring requirements.
FIGURE 13BRANCH CIRCUIT DISCONNECT LOCATION
! WARNINGTHE UNIT MUST BE PERMANENTLY GROUNDED. A GROUNDING LUG IS PRO-VIDED IN THE ELECTRIC HEAT ACCESS AREA FOR A GROUND WIRE.FAILURE TO GROUND THIS UNIT CAN RESULT IN FIRE OR ELECTRICALSHOCK CAUSING PROPERTY DAMAGE, SEVERE PERSONAL INJURY OR
24
XII. INDOOR AIR FLOW DATABelt-drive blower models have motor sheaves set for proper CFM at a typical externalstatic. See Tables C through G for blower performance.
XIII. CRANKCASE HEAT (OPTIONAL)Crankcase heat is not required on other models, but may be desirable under certainconditions.
XIV. PRE-START CHECK1. Is unit properly located and slightly slanted toward indoor condensate drain?2. Is ductwork insulated, weatherproofed, with proper spacing to combustible materi-als?
3. Is air free to travel to and from outdoor coil? (See Figure 4.)4. Is the wiring correct, tight, and according to unit wiring diagram?
FIGURE 14
25
5. Is unit grounded?6. Are field supplied air filters in place and clean?7. Do the outdoor fan and indoor blower turn freely without rubbing, and are they tighton the motor shafts?
XV. STARTUP1. Turn thermostat to “OFF,” turn “on” power supply at disconnect switch.2. Turn temperature setting as high as it will go.3. Turn fan switch to “ON.”4. Indoor blower should run. Be sure it is running in the right direction.5. Turn fan switch to “AUTO.” Turn system switch to “COOL” and turn temperature set-ting below room temperature. Unit should run in cooling mode.
6. Is outdoor fan operating correctly in the right direction?7. Is compressor running correctly.Record the following after the unit has run some time.A. Operating Mode _______________________________B. Discharge Pressures (High) _____________PSIG [kPa]C. Vapor Pressure at Compressors (Low) _____PSIG [kPa]D. Vapor Line Temperature at Compressors ______°F [C°].E. Indoor Dry Bulb __________________________°F [C°].F. Indoor Wet Bulb__________________________°F [C°].G.Outdoor Dry Bulb_________________________°F [C°].H. Outdoor Wet Bulb ________________________°F [C°].I. Voltage at Contactor ________________________VoltsJ. Current at Contactors ______________________ AmpsK. Model Number_________________________________L. Serial Number _________________________________M.Location______________________________________N. Owner _______________________________________O.Date_________________________________________
8. Turn thermostat system switch to “HEAT.” Unit compressors should stop. Raise tem-perature setting to above room temperature. Unit should run in heating mode andauxiliary heaters, if installed, should come on.
9. Check the refrigerant charge using the instructions located on unit charging chart.Replace service port caps. Service port cores are for system access only and will
R Y1 Y2 G C W1 W2 W3 B
TERMINAL BLOCK
st-A1125-12-00
COOL
POWER
FAN
HEAT
ONLY USED ON DUAL
FUEL OR HEAT PUMP
MODELSLOW VOLTAGETHERMOSTAT CONNECTIONS
FIGURE 15THERMOSTATCONNECTIONSDIAGRAM
ST-A1125-12-00
26
leak if not tightly capped.10. Adjust discharge air grilles and balance system.11. Check ducts for condensation and air leaks.12. Check unit for tubing and sheet metal rattles.13. Instruct the owner on operation and maintenance.14. Leave “INSTALLATION” and ”USE AND CARE“ instructions with owner
XVI. OPERATIONCOOLING MODEWith thermostat in the cool mode, fan auto and the room temperature higher than thethermostat setting:
A. Indoor blower contactor is energized through thermostat contact (G).
B. Compressor contactor is energized through thermostat contacts (Y1) and safety con-trols.
C. Economizer enthalpy control (if installed) controls operation of first-stage cooling andpositions fresh air damper to maintain mixed air temperature. Compressor operatesas required by second stage of thermostats.
D. The system will continue in cooling operation as long as all safety controls are closed,until the thermostat is satisfied.
HEATING MODEWith the thermostat in heat mode, fan on auto, and the room temperature lower thanthe thermostat setting, the Indoor blower contactor is energized through thermostat con-tact (G).
In the heating mode, the thermostat will energize one or more supplementary heaters.
XVII. MISCELLANEOUSREPLACEMENT PARTSContact your local distributor for a complete parts list.
! WARNINGONLY ELECTRIC HEATER KITS SUPPLIED BY THIS MANUFACTURER ASDESCRIBED IN THIS PUBLICATION HAVE BEEN DESIGNED, TESTED, ANDEVALUATED FOR USE WITH THIS UNIT. USE OF ANY OTHER MANUFAC-TURED ELECTRIC HEATERS INSTALLED WITHIN THIS UNIT MAY CAUSEHAZARDOUS CONDITIONS RESULTING IN PROPERTY DAMAGE, FIRE, BODI-LY INJURY OR DEATH.
27
AIR
-FL
OW
PE
RF
OR
MA
NC
E –
7.5
TO
N R
LK
L-
B09
0 M
OD
EL
S
1097
2328
1126
3100
[146
3]56
080
459
894
063
210
1066
471
377
213
1180
113
7383
014
3586
014
9788
915
5992
118
1695
019
0197
919
8710
0920
7210
3821
5710
6822
4332
00 [1
510]
576
876
612
1011
646
1089
678
722
781
1371
810
1433
839
1495
868
1557
898
1619
928
1880
957
1965
987
2051
1016
2136
1045
2222
2414
1075
2307
3300
[155
7]59
295
462
810
9666
011
6869
273
178
914
3181
814
9384
815
5587
716
1790
618
5993
519
4496
520
2999
421
1510
2322
0010
53
Capa
city
7.5
Ton
[26.
4 kW
]
2286
1082
2371
3400
[160
5]60
710
3064
311
8067
312
4771
073
979
814
9182
715
53
RPM
WR
PMW
RPM
WR
PMR
PMR
PMW
RPM
WR
PMW
RPM
WR
PMW
RPM
WR
PMW
RPM
WR
PMW
RPM
WR
PMW
2400
[113
3]—
——
—54
058
058
261
271
189
074
095
277
010
1479
910
7682
811
3885
712
0088
712
6192
915
3895
816
2398
717
0910
1717
9425
00 [1
180]
——
——
552
633
593
624
720
950
749
1012
778
1074
808
1136
837
1198
866
1260
895
1322
936
1602
965
1687
995
1773
1024
1858
2600
[122
7]—
——
—56
468
760
363
572
910
1075
810
7278
711
3481
611
9684
612
5887
513
2091
415
8194
316
6697
217
5110
0218
3710
3119
2227
00 [1
274]
——
539
670
577
744
614
648
737
1070
766
1132
796
1194
825
1256
854
1318
883
1380
921
1645
950
1730
980
1816
1009
1901
1038
1986
2800
[132
1]—
—55
473
359
080
162
566
074
611
3177
511
9280
412
5483
413
1686
313
7889
214
4092
817
0995
817
9498
718
8010
1619
6510
4620
5029
00 [1
369]
——
569
801
604
866
638
673
755
1191
784
1253
813
1315
842
1376
872
1438
906
1688
936
1773
965
1858
994
1944
1024
2029
1053
2115
3000
[141
6]54
674
185
486
961
793
165
068
576
312
5179
213
1382
213
7585
114
3788
014
9891
317
5294
318
3797
219
2310
0220
0810
3120
9310
6021
79
3500
[165
2]62
211
1265
812
7168
913
4471
974
880
715
5283
616
1386
516
7589
417
3792
019
8795
020
7297
921
5810
0922
4310
3823
2810
6724
1410
9724
9985
616
1588
616
7791
319
2394
320
0897
220
9410
0121
7910
3122
6410
6023
5010
8924
35
3600
[169
9]63
812
0267
213
6170
414
4072
875
781
516
1284
416
7487
417
3590
317
9792
820
5195
721
3698
622
2210
1623
0710
4523
9310
7524
7811
0425
63
Air
Flow
CFM
[L/s
]
1156
2499
1104
2392
1134
2478
1163
2563
1111
2456
1141
2542
1170
2627
RPM
WR
PMW
RPM
W10
4618
7910
7519
6511
0520
5010
5319
4410
8320
2911
1221
1410
6120
0810
9020
9311
1921
7810
6820
7210
9721
5711
2722
4310
7521
3611
0422
2111
3423
0710
8222
0011
1222
8511
4123
7110
9022
6411
1923
5011
4824
35
1126
2585
1155
2670
1185
2756
1119
2521
1148
2606
1178
2691
1133
2649
1163
2734
1192
2820
0.1
[.02
]0.
2 [.
05]
0.3
[.07
]0.
4 [.
10]
0.7
[.17
]0.
8 [.
20]
0.9
[.22
]1.
0 [.
25]
1.1
[.27
]1.
2 [.
30]
1.3
[.32
]1.
4 [.
35]
1.5
[.37
]1.
6 [.
40]
1.7
[.42
]1.
8 [.
45]
1.9
[.47
]2.
0 [.
50]
Exte
rnal
Sta
tic P
ress
ure—
Inch
es o
f Wat
er [k
Pa]
743
751
760
769
RPM 64
565
666
768
070
872
573
4
777
786
1107
1189
1274
1306W 66
471
776
982
888
795
610
24
1366
1426
0.6
[.15
]0.
5 [.
12]
1249
1309
1369
1430W 81
287
894
510
1710
6911
2911
89
1490
1550
1187
1247
1307
1368W 72
979
185
392
399
310
6911
44
1428
1488
Driv
e Pa
ckag
eL
MM
otor
H.P
. [W
]2.
0 [1
491.
4]2.
0 [1
491.
4]Bl
ower
She
ave
BK11
0BK
90M
otor
She
ave
1VP-
441V
P-44
Turn
s O
pen
12
34
56
12
34
56
RPM
682
650
620
587
555
523
869
838
806
774
742
710
N3.
0 [2
237.
1]BK
651V
P-44
12
34
56
1157
1106
1056
1005
954
904
NO
TES:
1. F
acto
ry s
heav
e se
tting
s ar
e sh
own
in b
old
prin
t.2.
Re-
adju
stm
ent o
f she
ave
requ
ired
to a
chie
ve ra
ted
airf
low
at A
RI m
inim
um E
.S.P
.3.
Do
not o
pera
te a
bove
blo
wer
RPM
sho
wn
as m
otor
ove
rload
ing
will
occ
ur.
4.D
o no
t set
mot
or s
heav
e be
low
one
turn
ope
n.
NO
TE: L
-Driv
e le
ft of
1st
bol
d lin
e, M
-Driv
e in
mid
dle
of b
old
lines
, N-D
rive
right
of 2
nd b
old
line.
AIR
FLO
W C
OR
RE
CT
ION
FA
CT
OR
S7.
5 TO
N [2
6.4
kW] 0.
980.
99TO
TAL
MBH
0.99
0.97
0.97
3000
[141
6]1.
001.
01
1.00
0.99
1.02
3400
[160
5]
POW
ER k
W1.
000.
991.
00
3200
[151
0]
0.94
SEN
SIBL
E M
BH0.
91
2800
[132
1]AC
TUAL
—CF
M[L
/s]
2600
[122
7]1.
02
1.01
1.05
3600
[169
9]1.
03
1.02
1.08
3800
[179
3]
CO
MP
ON
EN
T A
IR R
ES
ISTA
NC
E, I
WC
7.
5 TO
N [2
6.4
kW]
Com
pone
nt
Stan
dard
Indo
or A
irflo
w—
CFM
[L/s
]24
00[1
133]
2600
[122
7]28
00[1
321]
3000
[141
6]32
00[1
510]
3400
[160
4]36
00[1
699]
Res
ista
nce—
Inch
es W
ater
[kPa
]
Wet
Coi
l0.
047
[0.0
12]
0.05
1[0
.013
]0.
055
[0.0
14]
0.06
0[0
.015
]0.
065
[0.0
16]
0.07
1[0
.018
]0.
076
[0.0
19]
Econ
omiz
er10
0% R
.A. D
ampe
r Ope
n0.
05[0
.012
]0.
06[0
.015
]0.
07[0
.017
]0.
08[0
.020
]0.
09[0
.022
]0.
10[0
.025
]0.
11[0
.027
]H
oriz
onta
l Eco
nom
izer
100%
R.A
. Dam
per O
pen
0.03
[0.0
07]
0.04
[0.0
09]
0.04
[0.0
10]
0.05
[0.0
11]
0.05
[0.0
12]
0.06
[0.0
14]
0.06
[0.0
15]
Conc
entr
ic D
iffus
er R
XRN
-FA6
5 or
FA
75 &
Tra
nsiti
on R
XMC-
CD04
DN
A.0
17[0
.042
].0
20[0
.050
].0
25[0
.062
].0
31[0
.077
].0
37[0
.092
]D
NA
Conc
entr
ic D
iffus
er R
XRN
-AA6
1 or
AA
71 &
Tra
nsiti
on R
XMC-
CE05
DN
AD
NA
DN
AD
NA
DN
AD
NA
.017
[0.0
42]
Hor
izon
tal E
cono
miz
er
100%
O.A
. Dam
per O
pen
0.08
[0.0
20]
0.08
[0.0
20]
0.08
[0.0
20]
0.10
[0.0
24]
0.11
[0.0
27]
0.12
[0.0
30]
0.13
[0.0
32]
NO
TES:
1. M
ultip
ly c
orre
ctio
n fa
ctor
tim
es g
ross
per
form
ance
dat
a.2.
Res
ultin
g se
nsib
le c
apac
ity c
anno
t exc
eed
tota
l cap
acity
.
[]
Des
ign
ates
Met
ric
Co
nve
rsio
ns
NO
TE: A
dd c
ompo
nent
resi
stan
ce to
duc
t res
ista
nce
to d
eter
min
e to
tal e
xter
nal s
tatic
pre
ssur
e.D
NA
= D
ata
not A
vaila
ble.
CO
MP
ON
EN
T A
IR R
ES
ISTA
NC
E, I
WC
-B09
07.
5 TO
N [
26.4
kW
]A
IRF
LO
W C
OR
RE
CT
ION
FA
CTO
RS
-B09
07.
5 TO
N [
26.4
kW
]
28
AIR
-FL
OW
PE
RF
OR
MA
NC
E –
10
TON
RL
KL
B12
0 M
OD
EL
S
1090
2875
1110
3900
[184
1]69
915
2672
716
0175
416
7578
217
5080
918
2483
718
9986
419
7392
720
1594
820
8096
821
9498
823
0710
0824
2110
2925
3410
5726
4810
6927
6140
00 [1
888]
713
1609
740
1683
768
1758
795
1832
823
1907
850
1961
878
2056
935
2085
955
2199
975
2312
996
2426
1016
2539
1043
2653
1070
2767
2988
1077
2880
4100
[193
5]72
616
9275
417
6678
118
4180
919
1583
619
9086
420
6492
220
9194
222
0496
323
1898
324
3110
0325
4510
2426
5810
5627
7210
8428
8510
8429
9942
00 [1
982]
740
1774
767
1849
795
1923
822
1998
850
2072
877
2147
Exte
rnal
Sta
tic P
ress
ure—
Inch
es o
f Wat
er [k
Pa]
3200
[151
0]—
——
——
—65
711
7071
512
4574
213
1977
013
9479
714
6882
515
4385
216
1788
016
9295
616
9897
617
0399
618
1710
1719
3033
00 [1
557]
——
——
673
1179
701
1253
728
1328
756
1402
783
1477
811
1551
838
1626
866
1700
943
1705
963
1708
948
1822
976
1935
1024
2049
3400
[160
5]—
——
—68
712
6171
413
3674
214
1076
914
8579
715
5982
416
3485
217
0887
917
6395
018
1197
118
2796
219
4198
920
5410
3221
6835
00 [1
652]
——
673
1270
700
1344
728
1419
755
1493
783
1588
810
1642
838
1717
865
1791
938
1813
958
1832
978
1946
975
2059
1003
2173
1039
2286
3600
[169
9]—
—68
613
5271
414
2774
115
0176
915
7679
616
5082
417
2585
117
9987
918
7494
518
9296
619
5198
620
6598
921
7810
1622
9210
4724
0537
00 [1
746]
672
1361
700
1435
727
1510
755
1584
782
1659
810
1733
837
1808
865
1882
933
1896
953
1956
973
2070
993
2183
1002
2297
1030
2410
1054
2524
3800
[179
3]68
614
4371
315
1874
115
9276
816
6779
617
4182
318
1886
118
9087
819
6594
020
0396
020
7598
121
8910
0123
0210
1624
1610
4325
2910
6226
43
4300
[202
9]75
318
5778
119
3280
820
0683
620
8185
321
5591
722
1593
723
2895
724
4297
825
5599
826
6910
1827
8210
3928
9610
8330
0911
1131
2310
9932
3693
022
0995
023
2397
024
3899
025
5010
1126
6310
3127
7710
7028
9010
9730
0410
9231
17
4700
[221
8]80
721
8883
522
6386
223
3790
624
6292
725
7694
726
8996
728
0398
829
1610
0830
3010
2831
4310
4832
5710
6933
7111
3734
8411
6535
9811
3037
11
1130
3102
1097
2994
1117
3107
1138
3221
1105
3112
1125
3226
1145
3339
1037
2044
1057
2157
1077
2271
1044
2162
1065
2276
1085
2390
1052
2281
1072
2395
1092
2508
1059
2400
1080
2513
1100
2627
1067
2519
1087
2632
1108
2746
1075
2637
1095
2751
1115
2864
1082
2756
1102
2870
1123
2983
1120
3350
1140
3453
1160
3577
1112
3231
1133
3345
1153
3458
1150
3825
1170
3938
1190
4052
1191
3442
—11
5032
1511
7133
2911
5833
34—
1178
3448
1166
3453
1186
3566
1098
2384
1118
2498
1105
2503
1125
2617
1113
2622
1133
2735
1120
2740
1141
2854
1128
2859
1148
2973
1135
2978
1156
3091
1143
3097
1163
3210
1181
3690
——
1173
3572
1193
3685
——
——
——
1199
3561
——
——
——
——
——
1138
2611
1159
2725
1179
2838
1146
2730
1166
2844
1186
2957
1153
2849
1174
2962
1194
3076
1161
2968
1181
3081
——
1168
3086
1189
3200
——
1176
3205
1196
3318
——
1183
3324
——
——
——
——
——
——
——
——
——
——
——
4400
[207
7]76
719
4079
420
1482
220
8984
921
6387
722
3892
423
3394
524
4796
525
6098
526
7410
0627
8710
2629
0110
4630
1410
9731
2811
2432
4111
0733
5545
00 [2
124]
780
2023
808
2097
835
2172
863
2248
912
2338
1188
932
2452
4600
[217
1]79
421
0582
121
8084
022
5487
623
2991
924
5794
025
7196
026
8498
027
9810
0029
1110
2130
2510
4131
3810
6132
5211
2433
6511
5134
7911
2235
9295
225
8597
326
7999
327
9310
1329
0610
3330
2010
5431
3311
1032
4711
3833
6011
1534
7438
09—
1127
3468
1148
3582
1168
3695
—
1142
3706
1163
3819
1183
3933
1135
3587
1155
3701
1175
3814
——
——
1196
3928
——
——
——
——
——
——
——
——
——
——
4800
[226
5]82
122
7184
823
4587
624
2091
425
8193
426
9595
528
0897
529
2299
530
3510
1531
4910
3632
6210
5633
7610
7634
8911
5136
0311
7837
1611
3738
3011
5739
4311
7840
5711
9841
70—
——
——
——
——
—
RPM
WR
PMW
RPM
WR
PMW
RPM
WR
PMW
RPM
WR
PMW
RPM
WR
PMW
RPM
WR
PMW
RPM
WR
PMW
RPM
WR
PMW
RPM
WR
PMW
RPM
W0.
1 [.
02]
0.2
[.05
]0.
3 [.
07]
0.4
[.10
]0.
5 [.
12]
0.6
[.15
]0.
7 [.
17]
0.8
[.20
]0.
9 [.
22]
1.0
[.25
]1.
1 [.
27]
1.2
[.30
]1.
3 [.
32]
1.4
[.35
]1.
5 [.
37]
RPM
1.6
[.40
]1.
7 [.
42]
1.8
[.45
]W
RPM
WR
PMW
RPM
W1.
9 [.
47]
2.0
[.50
]2.
1 [.
52]
2.2
[.55
]2.
3 [.
57]
Air
Flow
CFM
[L/s
]
Capa
city
10 T
on [3
5.2
kW]
Driv
e Pa
ckag
eL
MM
otor
H.P
. [W
]2.
0 [1
491.
4]3.
0 [2
237.
1]Bl
ower
She
ave
BK90
BK65
Mot
or S
heav
e1V
P-44
1VP-
44Tu
rns
Ope
n1
23
45
61
23
45
6R
PM84
581
077
573
970
466
911
3810
8910
4199
294
389
4
NO
TES:
1. F
acto
ry s
heav
e se
tting
s ar
e sh
own
in b
old
prin
t.2.
Re-
adju
stm
ent o
f she
ave
requ
ired
to a
chie
ve ra
ted
airf
low
at A
RI m
inim
um E
.S.P
.3.
Do
not o
pera
te a
bove
blo
wer
RPM
sho
wn
as m
otor
ove
rload
ing
will
occ
ur.
4.D
o no
t set
mot
or s
heav
e be
low
one
turn
ope
n.
NO
TE: L
-Driv
e le
ft of
bol
d lin
e, M
-Driv
e rig
ht o
f bol
d lin
e.
AIR
FL
OW
CO
RR
EC
TIO
N F
AC
TO
RS
10 T
ON
[35
.2 k
W]
0.98
0.99
TOTA
L M
BH0.
96
0.99
0.97
0.97
3800
[179
3]1.
001.
01
1.00
0.99
1.02
4200
[198
2]
POW
ER k
W0.
981.
000.
981.
00
4000
[188
8]1.
03
1.01
1.07
4600
[217
1]
0.95
SEN
SIBL
E M
BH0.
910.
93
3600
[169
9]AC
TUAL
—CF
M[L
/s]
3200
[151
0]34
00[1
605]
1.04
1.01
1.09
4800
[226
5]1.
02
1.01
1.05
4400
[207
7]
CO
MP
ON
EN
T A
IR R
ES
ISTA
NC
E, I
WC
10
TO
N [
35.2
kW
]
Com
pone
nt
Stan
dard
Indo
or A
irflo
w—
CFM
[L/s
]
Conc
entr
ic D
iffus
er R
XRN
-FA6
5 or
FA75
& T
rans
ition
RXM
C-CD
040.
31[0
.077
]0.
37[0
.092
]D
NA
DN
AD
NA
DN
AD
NA
Conc
entr
ic D
iffus
er R
XRN
-AA6
1 or
AA71
& T
rans
ition
RXM
C-CE
05D
NA
3200
[151
0]34
00[1
604]
3600
[169
9]38
00[1
793]
4000
[188
8]42
00[1
982]
4400
[207
6]
DN
A0.
17[0
.042
]0.
18[0
.045
]0.
21[0
.052
]
Res
ista
nce—
Inch
es W
ater
[kPa
]
0.24
[0.0
60]
0.27
[0.0
67]
Hor
izon
tal E
cono
miz
er
100%
O.A
. Dam
per O
pen
0.11
[0.0
27]
0.12
[0.0
30]
0.13
[0.0
32]
0.15
[0.0
.36]
0.16
[0.0
40]
0.18
[0.0
44]
Wet
Coi
l0.
065
[0.0
16]
0.07
1[0
.018
]0.
076
[0.0
19]
0.08
2[0
.020
]0.
087
[0.0
22]
0.09
3[0
.023
]0.
099
[0.0
25]
0.19
[0.0
47]
Econ
omiz
er10
0% R
.A. D
ampe
r Ope
n0.
09[0
.022
]0.
10[0
.025
]0.
11[0
.027
]0.
12[0
.030
]0.
13[0
.032
]0.
14[0
.035
]0.
15[0
.037
]
DN
A
4600
[217
1]
DN
A
0.10
5[0
.026
]
0.20
[0.5
0]
0.16
[0.0
40]
0.10
[0.0
24]
DN
A
4800
[226
5]
Hor
izon
tal E
cono
miz
er10
0% R
.A. D
ampe
r Ope
n0.
05[0
.012
]0.
06[0
.014
]0.
06[0
.015
]0.
07[0
.017
]0.
08[0
.020
]0.
09[0
.021
]0.
09[0
.022
]
DN
A
0.11
0[0
.027
]
0.21
[0.0
52]
0.17
[0.0
42]
0.10
[0.0
25]
Conc
entr
ic D
iffus
er R
XRN
-AA6
6 or
AA76
& T
rans
ition
RXM
C-CF
06D
NA
DN
AD
NA
DN
AD
NA
DN
AD
NA
0.31
[0.0
77]
0.32
[0.0
80]
NO
TE: A
dd c
ompo
nent
resi
stan
ce to
duc
t res
ista
nce
to d
eter
min
e to
tal e
xter
nal s
tatic
pre
ssur
e.D
NA
= D
ata
not A
vaila
ble.
NO
TES:
1. M
ultip
ly c
orre
ctio
n fa
ctor
tim
es g
ross
per
form
ance
dat
a.2.
Res
ultin
g se
nsib
le c
apac
ity c
anno
t exc
eed
tota
l cap
acity
.
[]
Des
ign
ates
Met
ric
Co
nve
rsio
ns
CO
MP
ON
EN
T A
IR R
ES
ISTA
NC
E, I
WC
-B12
010
TO
N [
35.2
kW
]
AIR
FL
OW
CO
RR
EC
TIO
N F
AC
TOR
S-B
120
10 T
ON
[35
.2 k
W]
29
AIR
-FL
OW
PE
RF
OR
MA
NC
E –
12.
5 TO
N R
LK
L B
151
MO
DE
LS
38
00
[17
93
]—
——
——
—8
28
16
05
85
41
66
18
79
17
22
90
41
78
69
29
18
53
95
41
92
49
79
19
98
10
04
20
75
10
28
21
56
10
52
22
41
10
76
23
28
10
99
24
20
11
23
25
14
11
46
26
13
11
69
27
14
11
92
28
19
12
15
29
28
40
00
[18
88
]—
——
—8
30
17
35
85
51
79
68
80
18
59
90
51
92
79
30
19
97
95
52
07
29
79
21
49
10
04
22
30
10
28
23
15
10
52
24
03
10
75
24
94
10
99
25
89
11
22
26
87
11
45
27
89
11
68
28
94
11
90
30
02
12
13
31
14
12
35
32
30
42
00
[19
82
]—
—8
32
18
77
85
81
94
18
83
20
08
90
82
07
99
32
21
53
95
72
23
09
81
23
12
10
05
23
96
10
29
24
84
10
53
25
75
10
76
26
70
10
99
27
69
11
22
28
70
11
45
29
75
11
68
30
84
11
90
31
96
12
12
33
12
12
34
34
30
12
56
35
53
44
00
[20
76
]8
36
20
29
86
22
09
68
86
21
67
91
12
24
19
36
23
19
96
02
40
09
84
24
85
10
08
25
73
10
31
26
64
10
55
27
59
10
78
28
58
11
01
29
59
11
24
30
65
11
46
31
73
11
69
32
85
11
91
34
01
12
13
35
20
12
35
36
42
12
56
37
68
12
78
38
97
46
00
[21
71
]8
67
22
63
89
12
33
79
16
24
15
94
02
49
69
64
25
81
98
82
66
91
01
22
76
01
03
52
85
51
05
82
95
41
08
13
05
61
10
43
16
11
12
73
27
01
14
93
38
21
17
13
49
71
19
33
61
61
21
53
73
91
23
63
86
51
25
83
99
41
27
94
12
71
30
04
26
34
80
0[2
26
5]
89
72
51
89
22
25
99
94
62
68
49
70
27
72
99
32
86
41
01
72
95
91
04
03
05
71
06
33
15
91
08
63
26
51
10
83
37
31
13
13
48
51
15
33
60
11
17
53
72
01
19
63
84
31
21
83
96
91
23
94
09
81
26
14
23
11
28
24
36
7—
——
—5
00
0[2
35
9]
92
92
79
59
53
28
83
97
62
97
51
00
03
07
01
02
33
16
81
04
63
27
01
06
93
37
51
09
13
48
41
11
43
59
71
13
63
71
21
15
83
83
11
17
93
95
41
20
14
08
01
22
24
20
91
24
44
34
21
26
44
47
91
28
54
61
8—
——
——
—5
20
0[2
45
4]
96
13
09
39
84
31
88
10
07
32
86
10
30
33
88
10
53
34
94
10
76
36
03
10
98
37
15
11
20
38
31
11
42
39
50
11
64
40
72
11
86
41
99
12
07
43
28
12
28
44
61
12
49
45
97
12
70
47
37
12
90
48
80
——
——
——
——
54
00
[25
48
]9
93
34
12
10
16
35
14
10
39
36
19
10
62
37
28
10
84
38
41
11
06
39
56
11
28
40
76
11
50
41
98
11
71
43
24
11
93
44
54
12
14
45
87
12
35
47
23
12
56
48
63
12
76
50
07
12
96
51
53
——
——
——
——
——
56
00
[26
43
]1
02
63
75
21
04
93
86
11
07
13
97
41
09
34
08
91
11
54
20
91
13
74
33
11
15
94
45
81
18
04
58
71
20
14
72
01
22
24
85
71
24
34
99
71
26
35
14
01
28
45
28
7—
——
——
——
——
——
——
—5
80
0[2
73
7]
10
60
41
14
10
82
42
30
11
04
43
49
11
26
44
72
11
47
45
98
11
69
47
28
11
90
48
61
12
11
49
97
12
32
51
37
12
52
52
81
12
72
54
28
12
92
55
78
——
——
——
——
——
——
——
——
NO
TE:
L-D
rive
left
of b
old
line
, M-D
rive
righ
t of b
old
line
.
`
1.0
11
.02
1.0
21
.03
1.0
31
.03
0.9
30
.96
1.0
01
.00
1.0
11
.04
1.0
70
.99
1.0
01
.00
1.1
11
.14
1.1
81
.21
1.2
51
.28
1.0
41
.05
1.0
61
.07
[17
93
][1
88
8]
[19
82
]1
.01
1.0
2[2
07
6]
[21
71
]1
.02
1.0
30
.98
0.9
91
.00
[22
65
][2
35
9]
[24
54
][2
54
8]
[26
43
][2
73
7]
48
00
50
00
52
00
54
00
56
00
58
00
44
00
46
00
38
00
40
00
42
00
[.08
][.0
9]
[.09
][.1
0]
[.11
]0
.38
0.4
00
.43
[.06
][.0
6]
[.07
][.0
7]
[.07
][.0
8]
0.3
6[.1
2]
[.13
]0
.23
0.2
50
.27
0.2
90
.30
0.3
20
.34
0.3
00
.33
0.3
60
.40
0.4
40
.48
0.5
2[.0
5]
[.05
][.0
6]
[.07
][.0
7]
[.08
][.0
9]
[.10
][.1
1]
[.03
][.0
2]
[.02
][.0
2]
[.02
][.0
2]
[.02
]0
.19
0.2
10
.24
0.2
7[.0
2]
[.03
][.0
3]
[.03
]0
.10
0.1
00
.11
0.1
10
.12
0.1
3[.0
5]
[.05
]0
.08
0.0
9[.0
5]
[.05
]0
.07
0.0
70
.08
[.03
][.0
3]
[.03
][.0
4]
[.04
][.0
4]
[.04
]0
.20
0.2
1
0.0
8
0.2
2[.0
2]
[.03
][.0
3]
[.03
][.0
3]
[.03
][.0
3]
0.1
20
.13
0.1
40
.15
0.1
60
.17
0.1
80
.19
0.1
10
.11
0.1
20
.13
0.1
30
.14
[.02
][.0
2]
[.02
][.0
2]
0.0
90
.09
0.1
00
.10
[23
59
][2
45
4]
[25
48
][2
64
3]
[27
37
]5
40
05
60
05
80
0[1
79
3]
[18
88
][1
98
2]
[20
76
][2
17
1]
[22
65
]
4. D
rive
dat
a s
how
n is
for
horiz
onta
l airf
low
with
dry
coi
l. A
dd c
ompo
nent
res
ista
nce
(be
low
) to
duc
t res
ista
nce
to d
ete
rmin
e to
tal E
xtern
al S
tatic
Pre
ss
ure.
38
00
40
00
42
00
44
00
46
00
48
00
50
00
52
00
2. D
o no
t set
mot
or
she
ave
belo
w m
inim
um o
r m
axim
um tu
rns
ope
n s
how
n.3
. Re-
adju
stm
ent
of s
heav
e re
quire
d to
ach
ieve
rate
d a
irflo
w a
t AH
RI m
inim
um E
xtern
al S
tatic
Pre
ss
ure
82
4|
12
94
12
56
11
77
11
36
10
94
NO
TES
: 1
. Fac
tory
she
ave
set
tings
are
sho
wn
in b
old
type
.
Tur
ns O
pen
01
23
49
66
92
0R
PM|
10
51
10
09
LM
Mot
or
H.P
. [W
]
45
66
01
2M
oto
r S
heav
e1
VP
-44
1V
P-6
5
Driv
e P
acka
ge3
[22
37
.1]
5 [3
72
8.5
]B
low
er S
heav
eB
K72
HB
K85
H
30
XVIII. HEATER KITCHARACTERISTICSTABLE AAUXILIARY HEATERKITS CHARACTERIS-TICS AND APPLICA-TION (RLKL MODELS)
Model
Num
ber
RXJJ- Heater
Kit N
ominal
kW
Heater K
it
Single Pow
er Supply for B
oth Unit a
nd Heater K
it
208/240 VO
LT, T
HREE PHAS
E, 60 HZ, AUXILIAR
Y ELEC
TRIC HEA
TER KITS CH
ARAC
TERISTICS
AND APP
LICA
TION Se
parate Pow
er Supply for B
oth Unit a
nd Heater K
it
Air C
onditio
ner
Heater K
itAir C
onditio
ner
No. of
Sequence
Steps
Rated Heater
kW @
208/240 V
Heater
KBTU
/Hr @
208/240 V
Heater
Amp. @
208/240 V
Unit M
in. C
kt.
Ampacity @
208/240 V
Over C
urrent Protection
Device Size
Min. C
kt.
Ampacity
208/240 V
Max. F
use Size
208/240 V
Min. C
ircuit
Ampacity
208/240V
Over C
urrent Protection
Device Size
Min./Max @
208 V
Min./Max @
240 V
Min. M
ax. @
208 V
Min. M
ax. @
240 V
RLKL
-B09
0CL
No H
eat
——
——
40/4
050
/60
50/6
0—
—40
/40
50/6
050
/60
CC10
C1
7.2/
9.6
24.5
6/32
.75
20/2
3.1
40/4
050
/60
50/6
025
/29
25/3
0—
——
CC15
C1
10.8
/14.
436
.84/
49.1
330
/34.
648
/54
50/6
060
/60
38/4
440
/45
——
—CC
20C
114
.4/1
9.2
49.1
3/65
.540
.46.
260
/68
60/6
070
/70
50/5
850
/60
——
—CC
30C
121
.6/2
8.8
73.6
9/98
.25
60/6
9.3
85/9
790
/90
100/
100
75/8
780
/90
——
—CC
31C
121
.6/2
8.8
73.6
9/98
.25
60/6
9.3
85/9
790
/90
100/
100
75/8
780
/90
——
—CC
40C
128
.8/3
8.4
98.2
5/13
180
.1/9
2.4
111/
126
125/
125
150/
150
101/
116
110/
125
——
—CC
41C
128
.8/3
8.4
98.2
5/13
180
.1/9
2.4
111/
126
125/
125
150/
150
101/
116
110/
125
——
—
RLK
L-B0
90CM
No
Hea
t—
——
—40
/40
50/6
050
/60
——
40/4
050
/60
50/6
0CC
10C
17.
2/9.
624
.56/
32.7
520
/23.
140
/40
50/6
050
/60
25/2
925
/30
——
—CC
15C
110
.8/1
4.4
36.8
4/49
.13
30/3
4.6
48/5
450
/60
60/6
038
/44
40/4
5—
——
CC20
C1
14.4
/19.
249
.13/
65.5
40/4
6.2
60/6
860
/60
70/7
050
/58
50/6
0—
——
CC30
C1
21.6
/28.
873
.69/
98.2
560
/69.
385
/97
90/9
010
0/10
075
/87
80/9
0—
——
CC31
C1
21.6
/28.
873
.69/
98.2
560
/69.
385
/97
90/9
010
0/10
075
/87
80/9
0—
——
CC40
C1
28.8
/38.
498
.25/
131
80.1
/92.
411
1/12
612
5/12
515
0/15
010
1/11
611
0/12
5—
——
CC41
C1
28.8
/38.
498
.25/
131
80.1
/92.
411
1/12
612
5/12
515
0/15
010
1/11
611
0/12
5—
——
RLK
L-B0
90CN
No
Hea
t—
——
—45
/45
60/6
060
/60
——
45/4
560
/60
60/6
0CC
10C
17.
2/9.
624
.56/
32.7
520
/23.
145
/46
60/6
060
/60
25/2
925
/30
——
—CC
15C
110
.8/1
4.4
36.8
4/49
.13
30/3
4.6
54/6
060
/60
60/6
038
/44
40/4
5—
——
CC20
C1
14.4
/19.
249
.13/
65.5
40/4
6.2
67/7
570
/70
80/8
050
/58
50/6
0—
——
CC30
C1
21.6
/28.
873
.69/
98.2
560
/69.
392
/103
100/
100
110/
110
75/8
780
/90
——
—CC
31C
121
.6/2
8.8
73.6
9/98
.25
60/6
9.3
92/1
0310
0/10
011
0/11
075
/87
80/9
0—
——
CC40
C1
28.8
/38.
498
.25/
131
80.1
/92.
411
7/13
212
5/12
515
0/15
010
1/11
611
0/12
5—
——
CC41
C1
28.8
/38.
498
.25/
131
80.1
/92.
411
7/13
212
5/12
515
0/15
010
1/11
611
0/12
5—
——
31
Model
Num
ber
RXJJ- Heater
Kit N
ominal
kW
Heater K
it
Single Pow
er Supply for B
oth Unit a
nd Heater K
it
480 VO
LT, T
HREE PHAS
E, 60 HZ, AUXILIAR
Y ELEC
TRIC HEA
TER KITS CH
ARAC
TERISTICS
AND APP
LICA
TION
Separate Pow
er Supply for B
oth Unit a
nd Heater K
it
Air C
onditio
ner
Heater K
itAir C
onditio
ner
No. of
Sequence
Steps
Rated Heater
kW @
208/240 V
Heater
KBTU
/Hr @
208/240 V
Heater
Amp. @
208/240 V
Unit M
in. C
kt.
Ampacity @
208/240 V
Over C
urrent Protection
Device Size
Min. C
kt.
Ampacity
208/240 V
Max. F
use Size
208/240 V
Min. C
ircuit
Ampacity
208/240V
Over C
urrent Protection
Device Size
Min./Max @
208 V
Min./Max @
240 V
Min. M
ax. @
208 V
Min. M
ax. @
240 V
RLKL
-B09
0DL
No H
eat
——
——
2025
/30
——
—20
25/3
0—
CC10
D1
9.6
32.7
511
.520
25/3
0—
1515
——
—CC
15D
114
.449
.13
17.3
2730
/30
—22
25—
——
CC20
D1
19.2
65.5
23.1
3435
/35
—29
30—
——
CC30
D1
28.8
98.2
534
.649
50/5
0—
4445
——
—CC
31D
128
.898
.25
34.6
4950
/50
—44
45—
——
CC40
D1
38.4
131
46.2
6370
/70
—58
60—
——
CC41
D1
38.4
131
46.2
6370
/70
—58
60—
——
RLK
L-B0
90D
MN
o H
eat
——
——
2025
/30
——
—20
25/3
0—
CC10
D1
9.6
32.7
511
.520
25/3
0—
1515
——
—CC
15D
114
.449
.13
17.3
2730
/30
—22
25—
——
CC20
D1
19.2
65.5
23.1
3435
/35
—29
30—
——
CC30
D1
28.8
98.2
534
.649
50/5
0—
4445
——
—CC
31D
128
.898
.25
34.6
4950
/50
—44
45—
——
CC40
D1
38.4
131
46.2
6370
/70
—58
60—
——
CC41
D1
38.4
131
46.2
6370
/70
—58
60—
——
RLK
L-B0
90D
NN
o H
eat
——
——
2330
/30
——
—23
30/3
0—
CC10
D1
9.6
32.7
511
.524
30/3
0—
1515
——
—CC
15D
114
.449
.13
17.3
3135
/35
—22
25—
——
CC20
D1
19.2
65.5
23.1
3840
/40
—29
30—
——
CC30
D1
28.8
98.2
534
.652
60/6
0—
4445
——
—CC
31D
128
.898
.25
34.6
5260
/60
—44
45—
——
CC40
D1
38.4
131
46.2
6770
/70
—58
60—
——
CC41
D1
28.8
98.2
534
.652
60/6
0—
4445
——
—
Model
Num
ber
RXJJ- Heater
Kit N
ominal
kW
Heater K
it
Single Pow
er Supply for B
oth Unit a
nd Heater K
it
600 VO
LT, T
HREE PHAS
E, 60 HZ, AUXILIAR
Y ELEC
TRIC HEA
TER KITS CH
ARAC
TERISTICS
AND APP
LICA
TION
Separate Pow
er Supply for B
oth Unit a
nd Heater K
it
Air C
onditio
ner
Heater K
itAir C
onditio
ner
No. of
Sequence
Steps
Rated Heater
kW @
208/240 V
Heater
KBTU
/Hr @
208/240 V
Heater
Amp. @
208/240 V
Unit M
in. C
kt.
Ampacity @
208/240 V
Over C
urrent Protection
Device Size
Min. C
kt.
Ampacity
208/240 V
Max. F
use Size
208/240 V
Min. C
ircuit
Ampacity
208/240V
Over C
urrent Protection
Device Size
Min./Max @
208 V
Min./Max @
240 V
Min. M
ax. @
208 V
Min. M
ax. @
240 V
RLK
L-B0
90YL
No
Hea
t—
——
—15
20/2
0—
——
1520
/20
—CC
10Y
19.
632
.75
9.2
1720
/20
—12
15—
——
CC15
Y1
14.4
49.1
313
.923
25/2
5—
1820
——
—CC
20Y
119
.265
.518
.529
30/3
0—
2425
——
—CC
30Y
128
.898
.25
27.7
4040
/40
—35
35—
——
CC40
Y1
38.4
131
3752
60/6
0—
4750
——
—
RLK
L-B0
90YM
No
Hea
t—
——
—15
20/2
0—
——
1520
/20
—CC
10Y
19.
632
.75
9.2
1720
/20
—12
15—
——
CC15
Y1
14.4
49.1
313
.923
25/2
5—
1820
——
—CC
20Y
119
.265
.518
.529
30/3
0—
2425
——
—CC
30Y
128
.898
.25
27.7
4040
/40
—35
35—
——
CC40
Y1
38.4
131
3752
60/6
0—
4750
——
—
RLK
L-B0
90YN
No
Hea
t—
——
—19
25/2
5—
——
1925
/25
—CC
10Y
19.
632
.75
9.2
2225
/25
—12
15—
——
CC15
Y1
14.4
49.1
313
.928
30/3
0—
1820
——
—CC
20Y
119
.265
.518
.534
35/3
5—
2425
——
—CC
30Y
128
.898
.25
27.7
4545
/45
—35
35—
——
CC40
Y1
38.4
131
3757
60/6
0—
4750
——
—
32
Model
Num
ber
RXJJ- Heater
Kit N
ominal
kW
Heater K
it
Single Pow
er Supply for B
oth Unit a
nd Heater K
it
208/240 VO
LT, T
HREE PHAS
E, 60 HZ, AUXILIAR
Y ELEC
TRIC HEA
TER KITS CH
ARAC
TERISTICS
AND APP
LICA
TION
Separate Pow
er Supply for B
oth Unit a
nd Heater K
it
Air C
onditio
ner
Heater K
itAir C
onditio
ner
No. of
Sequence
Steps
Rated Heater
kW @
208/240 V
Heater
KBTU
/Hr @
208/240 V
Heater
Amp. @
208/240 V
Unit M
in. C
kt.
Ampacity @
208/240 V
Over C
urrent Protection
Device Size
Min. C
kt.
Ampacity
208/240 V
Max. F
use Size
208/240 V
Min. C
ircuit
Ampacity
208/240V
Over C
urrent Protection
Device Size
Min./Max @
208 V
Min./Max @
240 V
Min. M
ax. @
208 V
Min. M
ax. @
240 V
RLKL
-B12
0CL
No
Hea
t—
——
—51
/51
60/8
060
/80
——
51/5
160
/80
60/8
0CC
10C
17.
2/9.
624
.56/
32.7
520
/23.
151
/51
60/8
060
/80
25/2
925
/30
——
—CC
15C
110
.8/1
4.4
36.8
4/49
.13
30/3
4.6
51/5
460
/80
60/8
038
/44
40/4
5—
——
CC20
C1
14.4
/19.
249
.13/
65.5
40/4
6.2
60/6
860
/80
70/8
050
/58
50/6
0—
——
CC30
C1
21.6
/28.
873
.69/
98.2
560
/69.
385
/97
90/9
010
0/10
075
/87
80/9
0—
——
CC40
C1
28.8
/38.
498
.25/
131
80.1
/92.
411
1/12
612
5/12
515
0/15
010
1/11
611
0/12
5—
——
CC50
C1
36.1
/48
123.
16/1
63.7
510
0.1/
115.
513
6/15
515
0/15
017
5/17
512
6/14
515
0/15
0—
——
Model
Num
ber
RXJJ- Heater
Kit N
ominal
kW
Heater K
it
Single Pow
er Supply for B
oth Unit a
nd Heater K
it
208/240 VO
LT, T
HREE PHAS
E, 60 HZ, AUXILIAR
Y ELEC
TRIC HEA
TER KITS CH
ARAC
TERISTICS
AND APP
LICA
TION Se
parate Pow
er Supply for B
oth Unit a
nd Heater K
it
Air C
onditio
ner
Heater K
itAir C
onditio
ner
No. of
Sequence
Steps
Rated Heater
kW @
208/240 V
Heater
KBTU
/Hr @
208/240 V
Heater
Amp. @
208/240 V
Unit M
in. C
kt.
Ampacity @
208/240 V
Over C
urrent Protection
Device Size
Min. C
kt.
Ampacity
208/240 V
Max. F
use Size
208/240 V
Min. C
ircuit
Ampacity
208/240V
Over C
urrent Protection
Device Size
Min./Max @
208 V
Min./Max @
240 V
Min. M
ax. @
208 V
Min. M
ax. @
240 V
RLKL
-B12
0CM
No
Hea
t—
——
—56
/56
70/8
070
/80
——
56/5
670
/80
70/8
0CC
10C
17.
2/9.
624
.56/
32.7
520
/23.
156
/56
70/8
070
/80
25/2
925
/30
——
—CC
15C
110
.8/1
4.4
36.8
4/49
.13
30/3
4.6
56/5
670
/80
70/8
038
/44
40/4
5—
——
CC20
C1
14.4
/19.
249
.13/
65.5
40/4
6.2
67/7
570
/80
80/8
050
/58
50/6
0—
——
CC30
C1
21.6
/28.
873
.69/
98.2
560
/69.
392
/103
100/
100
110/
110
75/8
780
/90
——
—CC
40C
128
.8/3
8.4
98.2
5/13
180
.1/9
2.4
117/
132
125/
125
150/
150
101/
116
110/
125
——
—CC
50C
136
.1/4
812
3.16
/163
.75
100.
1/11
5.5
142/
161
150/
150
175/
175
126/
145
150/
150
——
—
33
Model
Num
ber
RXJJ- Heater
Kit N
ominal
kW
Heater K
it
Single Pow
er Supply for B
oth Unit a
nd Heater K
itSe
parate Pow
er Supply for B
oth Unit a
nd Heater K
it
Air C
onditio
ner
Heater K
itAir C
onditio
ner
No. of
Sequence
Steps
Rated Heater
kW @
480 V
Heater
KBTU
/Hr @
480 V
Heater
Amp. @
480 V
Unit M
in. C
kt.
Ampacity @
480 V
Over C
urrent Protection
Device Size
Min. C
kt.
Ampacity
480 V
Max. F
use
Size 480 V
Min. C
ircuit
Ampacity
480V
Over C
urrent Protection
Device Size
Min./Max @
480 V
Min./Max @
480 V
Min. M
ax. @
480 V
Min. M
ax. @
480 V
RLKL
-B12
0DL
No
Hea
t—
——
—28
35/4
0—
——
2835
/40
—CC
10D
19.
632
.75
11.5
2835
/40
—15
15—
—CC
15D
114
.449
.13
17.3
2835
/40
—22
25—
——
CC20
D1
19.2
65.5
23.1
3435
/40
—29
30—
——
CC30
D1
28.8
98.2
534
.648
50/5
0—
4445
——
—CC
40D
138
.413
146
.263
70/7
0—
5860
——
—CC
50D
148
163.
7557
.777
80/8
0—
7380
——
—
Mod
elNum
ber
RXJJ- Heater
Kit N
ominal
kW
Heater K
it
Single Pow
er Supply for B
oth Unit a
nd Heater K
itSe
parate Pow
er Supply for B
oth Unit a
nd Heater K
it
Air C
onditio
ner
Heater K
itAir C
onditio
ner
No. of
Sequence
Steps
Rated Heater
kW @
480 V
Heater
KBTU
/Hr @
480 V
Heater
Amp. @
480 V
Unit M
in. C
kt.
Ampacity @
480 V
Over C
urrent Protection
Device Size
Min. C
kt.
Ampacity
480 V
Max. F
use Size
480 V
Min. C
ircuit
Ampacity
480V
Over C
urrent Protection
Device Size
Min./Max @
480 V
Min./Max @
480 V
Min. M
ax. @
480 V
Min. M
ax. @
480 V
RLKL
-B12
0DM
No
Hea
t—
——
—28
35/4
0—
——
2835
/40
—CC
10D
19.
632
.75
11.5
2835
/40
—15
15—
—CC
15D
114
.449
.13
17.3
2835
/40
—22
25—
——
CC20
D1
19.2
65.5
23.1
3435
/40
—29
30—
——
CC30
D1
28.8
98.2
534
.648
50/5
0—
4445
——
—CC
40D
138
.413
146
.263
70/7
0—
5860
——
—CC
50D
148
163.
7557
.777
80/8
0—
7380
——
—
480 VO
LT, T
HREE PHAS
E, 60 HZ, AUXILIAR
Y ELEC
TRIC HEA
TER KITS CH
ARAC
TERISTICS
AND APP
LICA
TION
480 VO
LT, T
HREE PHAS
E, 60 HZ, AUXILIAR
Y ELEC
TRIC HEA
TER KITS CH
ARAC
TERISTICS
AND APP
LICA
TION
34
Model
Num
ber
RXJJ- Heater
Kit N
ominal
kW
Heater K
it
Single Pow
er Supply for B
oth Unit a
nd Heater K
itSe
parate Pow
er Supply for B
oth Unit a
nd Heater K
it
Air C
onditio
ner
Heater K
itAir C
onditio
ner
No. of
Sequence
Steps
Rated Heater
kW @
600 V
Heater
KBTU
/Hr @
600 V
Heater
Amp. @
600 V
Unit M
in. C
kt.
Ampacity @
600 V
Over C
urrent Protection
Device Size
Min. C
kt.
Ampacity
600 V
Max. F
use
Size 600 V
Min. C
ircuit
Ampacity
600V
Over C
urrent Protection
Device Size
Min./Max @
600 V
Min./Max @
600 V
Min. M
ax. @
600 V
Min. M
ax. @
600 V
RLKL
-B12
0YL
No
Hea
t—
——
—22
25/3
0—
——
2225
/30
—CC
10Y
19.
632
.75
9.2
2225
/30
—12
15—
——
CC15
Y1
14.4
49.1
313
.922
25/3
0—
1820
——
—CC
20Y
119
.265
.518
.527
30/3
0—
2425
——
—CC
30Y
128
.898
.25
27.7
3840
/40
—35
35—
——
CC40
Y1
38.4
131
3750
50/5
0—
4750
——
—CC
50Y
148
163.
7546
.261
70/7
0—
5860
——
—
600 VO
LT, T
HREE PHAS
E, 60 HZ, AUXILIAR
Y ELEC
TRIC HEA
TER KITS CH
ARAC
TERISTICS
AND APP
LICA
TION
Model
Num
ber
RXJJ- Heater
Kit N
ominal
kW
Heater K
it
Single Pow
er Supply for B
oth Unit a
nd Heater K
itSe
parate Pow
er Supply for B
oth Unit a
nd Heater K
it
Air C
onditio
ner
Heater K
itAir C
onditio
ner
No. of
Sequence
Steps
Rated Heater
kW @
600 V
Heater
KBTU
/Hr @
600 V
Heater
Amp. @
600 V
Unit M
in. C
kt.
Ampacity @
600 V
Over C
urrent Protection
Device Size
Min. C
kt.
Ampacity
600 V
Max. F
use
Size 600 V
Min. C
ircuit
Ampacity
600V
Over C
urrent Protection
Device Size
Min./Max @
600 V
Min./Max @
600 V
Min. M
ax. @
600 V
Min. M
ax. @
600 V
RLKL
-B12
0YM
No
Hea
t—
——
—26
30/3
5—
——
2630
/35
—CC
10Y
19.
632
.75
9.2
2630
/35
—12
15—
——
CC15
Y1
14.4
49.1
313
.926
30/3
5—
1820
——
—CC
20Y
119
.265
.518
.527
30/3
0—
2425
——
—CC
30Y
128
.898
.25
27.7
4040
/40
—35
35—
——
CC40
Y1
38.4
131
3751
60/6
0—
4750
——
—CC
50Y
148
163.
7546
.263
70/7
0—
5860
——
—
600 VO
LT, T
HREE PHAS
E, 60 HZ, AUXILIAR
Y ELEC
TRIC HEA
TER KITS CH
ARAC
TERISTICS
AND APP
LICA
TION
35
Model
Num
ber
RXJJ- Heater
Kit N
ominal
kW
Heater K
it
Single Pow
er Supply for B
oth Unit a
nd Heater K
it
208/240 VO
LT, T
HREE PHAS
E, 60 HZ, AUXILIAR
Y ELEC
TRIC HEA
TER KITS CH
ARAC
TERISTICS
AND APP
LICA
TION Se
parate Pow
er Supply for B
oth Unit a
nd Heater K
it
Air C
onditio
ner
Heater K
itAir C
onditio
ner
No. of
Sequence
Steps
Rated Heater
kW @
208/240 V
Heater
KBTU
/Hr @
208/240 V
Heater
Amp. @
208/240 V
Unit M
in. C
kt.
Ampacity @
208/240 V
Over C
urrent Protection
Device Size
Min. C
kt.
Ampacity
208/240 V
Max. F
use Size
208/240 V
Min. C
ircuit
Ampacity
208/240V
Over C
urrent Protection
Device Size
Min./Max @
208 V
Min./Max @
240 V
Min. M
ax. @
208 V
Min. M
ax. @
240 V
RLKL
-B15
1CL
No H
eat
——
——
67/6
770
/80
70/8
0—
—67
/67
70/8
070
/80
CC10
C1
7.2/
9.6
24.5
6/32
.75
20/2
3.1
67/6
780
/80
80/8
025
/29
25/3
0—
——
CC15
C1
10.8
/14.
436
.84/
49.1
330
/34.
667
/67
80/8
080
/80
38/4
440
/45
——
—CC
20C
114
.4/1
9.2
49.1
3/65
.540
.46.
269
/77
80/8
080
/80
50/5
850
/60
——
—CC
30C
121
.6/2
8.8
73.6
9/98
.25
60/6
9.3
94/1
0610
0/10
011
0/11
075
/87
80/9
0—
——
CC40
C1
28.8
/38.
498
.25/
131
80.1
/92.
411
9/13
512
5/12
515
0/15
010
1/11
611
0/12
5—
——
CC50
C1
36.1
/48
123.
16/1
63.7
510
0.1/
115.
514
4/16
415
0/15
017
5/17
512
6/14
515
0/15
0—
——
RLK
L-B1
51CM
No
Hea
t—
——
—71
/71
75/9
075
/90
——
71/7
175
/90
75/9
0CC
10C
17.
2/9.
624
.56/
32.7
520
/23.
171
/71
80/9
080
/90
25/2
925
/30
——
—CC
15C
110
.8/1
4.4
36.8
4/49
.13
30/3
4.6
71/7
180
/90
80/9
038
/44
40/4
5—
——
CC20
C1
14.4
/19.
249
.13/
65.5
40/4
6.2
74/8
280
/90
90/9
050
/58
50/6
0—
——
CC30
C1
21.6
/28.
873
.69/
98.2
560
/69.
399
/111
100/
100
125/
125
75/8
780
/90
——
—CC
40C
128
.8/3
8.4
98.2
5/13
180
.1/9
2.4
124/
140
125/
125
150/
150
101/
116
110/
125
——
—CC
50C
136
.1/4
812
3.16
/163
.75
100.
1/11
5.5
149/
168
150/
150
175/
175
126/
145
150/
150
——
—
RLK
L-B1
51D
LN
o H
eat
——
——
3335
/40
——
—33
35/4
0—
CC10
D1
9.6
32.7
511
.533
40/4
0—
1515
——
—CC
15D
114
.449
.13
17.3
3340
/40
—22
25—
——
CC20
D1
19.2
65.5
23.1
3840
/40
—29
30—
——
CC30
D1
28.8
98.2
534
.652
60/6
0—
4445
——
—CC
40D
138
.413
146
.267
70/7
0—
5860
——
—CC
50D
148
163.
7557
.781
90/9
0—
7380
——
—
Model
Num
ber
RXJJ- Heater
Kit N
ominal
kW
Heater K
it
Single Pow
er Supply for B
oth Unit a
nd Heater K
it
480 VO
LT, T
HREE PHAS
E, 60 HZ, AUXILIAR
Y ELEC
TRIC HEA
TER KITS CH
ARAC
TERISTICS
AND APP
LICA
TION
Separate Pow
er Supply for B
oth Unit a
nd Heater K
it
Air C
onditio
ner
Heater K
itAir C
onditio
ner
No. of
Sequence
Steps
Rated Heater
kW @
480 V
Heater
KBTU
/Hr @
480 V
Heater
Amp. @
480 V
Unit M
in. C
kt.
Ampacity @
480 V
Over C
urrent Protection
Device Size
Min. C
kt.
Ampacity
480 V
Max. F
use Size
480 V
Min. C
ircuit
Ampacity
480V
Over C
urrent Protection
Device Size
Min./Max @
480 V
Min./Max @
480 V
Min. M
ax. @
480 V
Min. M
ax. @
480 V
RLKL
-B15
1DM
No H
eat
——
——
3640
/45
——
—36
40/4
5—
CC10
D1
9.6
32.7
511
.536
40/4
5—
1515
——
—CC
15D
114
.449
.13
17.3
3640
/45
—22
25—
——
CC20
D1
19.2
65.5
23.1
4245
/45
—29
30—
——
CC30
D1
28.8
98.2
534
.656
60/6
0—
4445
——
—CC
40D
138
.413
146
.271
80/8
0—
5860
——
—CC
50D
148
163.
7557
.785
90/9
0—
7380
——
—
Model
Num
ber
RXJJ- Heater
Kit N
ominal
kW
Heater K
it
Single Pow
er Supply for B
oth Unit a
nd Heater K
it
600 VO
LT, T
HREE PHAS
E, 60 HZ, AUXILIAR
Y ELEC
TRIC HEA
TER KITS CH
ARAC
TERISTICS
AND APP
LICA
TION
Separate Pow
er Supply for B
oth Unit a
nd Heater K
it
Air C
onditio
ner
Heater K
itAir C
onditio
ner
No. of
Sequence
Steps
Rated Heater
kW @
600 V
Heater
KBTU
/Hr @
600 V
Heater
Amp. @
600 V
Unit M
in. C
kt.
Ampacity @
600 V
Over C
urrent Protection
Device Size
Min. C
kt.
Ampacity
600 V
Max. F
use Size
600 V
Min. C
ircuit
Ampacity
600V
Over C
urrent Protection
Device Size
Min./Max @
600 V
Min./Max @
600 V
Min. M
ax. @
600 V
Min. M
ax. @
600 V
RLK
L-B1
51YL
No
Hea
t—
——
—28
30/3
5—
——
2830
/35
—CC
10Y
19.
632
.75
9.2
2830
/35
—12
15—
——
CC15
Y1
14.4
49.1
313
.928
30/3
5—
1820
——
—CC
20Y
119
.265
.518
.534
35/3
5—
2425
——
—CC
30Y
128
.898
.25
27.7
4545
/45
—35
35—
——
CC40
Y1
38.4
131
3757
60/6
0—
4750
——
—CC
50Y
148
163.
7546
.268
70/7
0—
5860
——
—
RLK
L-B1
51YM
No
Hea
t—
——
—28
30/3
5—
——
2830
/35
—CC
10Y
19.
632
.75
9.2
2830
/35
—12
15—
——
CC15
Y1
14.4
49.1
313
.928
30/3
5—
1820
——
—CC
20Y
119
.265
.518
.534
35/3
5—
2425
——
—CC
30Y
128
.898
.25
27.7
4545
/45
—35
35—
——
CC40
Y1
38.4
131
3757
60/6
0—
4750
——
—CC
50Y
148
163.
7546
.268
70/7
0—
5860
——
—
36
WARNING!
XIX. TROUBLE SHOOTING CHART
DISCONNECT ALL POWER TO UNIT BEFORE SERVICING. CONTACTOR MAY BREAK ONLY ONE SIDE. FAILURETO SHUT OFF POWER CAN CAUSE ELECTRICAL SHOCK RESULTING IN PERSONAL INJURY OR DEATH.
SYMPTOM POSSIBLE CAUSE REMEDYUnit will not run • Power off or loose electrical connection • Check for correct voltage at compressor contactor in control
box• Thermostat out of calibration-set too high • Reset• Defective contactor • Check for 24 volts at contactor coil - replace if contacts are
open• Blown fuses • Replace fuses• Transformer defective • Check wiring-replace transformer• High pressure control open (if provided) • Reset-also see high head pressure remedy-• Interconnecting low voltage wiring damaged • Replace thermostat wiring
Condenser fan runs, compressor • Run capacitor defective (single phase only) • Replacedoesn’t • Loose connection • Check for correct voltage at compressor -
check & tighten all connections• Compressor stuck, grounded or open motor winding • Wait at least 2 hours for overload to reset.open internal overload. If still open, replace the compressor.
• Low voltage condition At compressor terminals, voltage must be within 10% of ratingplate volts when unit is operating.
Insufficient cooling • Improperly sized unit • Recalculate load• Improper airflow • Check - should be approximately 400 CFM [188.78 L/s] per ton.• Incorrect refrigerant charge • Charge per procedure attached to unit service panel.• Air, non-condensibles or moisture in system • Recover refrigerant, evacuate & recharge, add filter drier• Incorrect voltage • At compressor terminals, voltage must be within 10% of rating
plate volts when unit is operating.
Compressor short cycles • Incorrect voltage • At compressor terminals, voltage must be ± 10% ofnameplate marking when unit is operating.
• Defective overload protector • Replace - check for correct voltage• Refrigerant undercharge • Add refrigerant
Registers sweat • Low evaporator airflow • Increase speed of blower or reduce restriction - replace air filter• Room thermostat set too low • Raise thermostat set point
High head-low vapor pressures • Restriction in liquid line, expansion device or filter drier • Remove or replace defective component• Flow check piston size too small • Change to correct size piston• Incorrect capillary tubes • Change coil assembly
High head-high or normal vapor • Dirty condenser coil • Clean coilpressure - Cooling mode • Refrigerant overcharge • Correct system charge
• Condenser fan not running • Repair or replace• Air or non-condensibles in system • Recover refrigerant, evacuate & recharge
High head-high or normal vapor • Low air flow - condenser coil • Check filters - correct to speedpressure - Heating mode • Refrigerant overcharge • Correct system charge
• Air or non-condensibles in system • Recover refrigerant, evacuate & recharge• Dirty condenser coil • Check filter - clean coil
Low head-high vapor pressures • Defective Compressor valves • Replace compressor
Low vapor - cool compressor - • Low evaporator airflow • Increase speed of blower or reduce restriction - replace airiced evaporator coil filter
• Operating below 65°F outdoors • Add Low Ambient Kit• Moisture in system • Recover refrigerant - evacuate & recharge - add filter drier• Liquid line limiting refrigerant flow • Replace drier
High vapor pressure • Excessive load • Recheck load calculation• Defective compressor • Replace
Fluctuating head & vapor • Severe overcharge • Adjust refrigerant chargepressures • Air or non-condensibles in system • Recover refrigerant, evacuate & recharge
Gurgle or pulsing noise at • Air or non-condensibles in system • Recover refrigerant, evacuate & rechargeexpansion device or liquid line
37
XX. WIRING DIAGRAMS
38
39
40
41
RLKL SYSTEM CHARGE CHARTSFIGURE 16
XXI. CHARGING CHARTS
42
FIGURE 17
10 TON, CIRCUIT 1
92-102259-21-00
SYSTEM CHARGE CHART - REFRIGERANT 410A
43
FIGURE 18
BOTH COMPRESSORS MUST BE OPERATING BEFORE CHECKING REFRIGERANT CHARGE. BEFORE FINAL REFRIGERANT CHECK!
RETURN AIR TEMPERATURE MUST BE WITHIN COMFORT CONDITIONS
44 CM 1012