a familiarization to speed governor anil chhikara motor licensing officer transport department gnct,...
TRANSCRIPT
![Page 1: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/1.jpg)
AFamiliarization
to Speed Governor
Anil ChhikaraAnil ChhikaraMotor Licensing OfficerMotor Licensing OfficerTransport Department Transport Department GNCT, DelhiGNCT, Delhi
![Page 2: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/2.jpg)
SPEED LIMITER
CABLE MECHANISM TYPE
FUEL MANAGEMENT TYPE
![Page 3: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/3.jpg)
SPEED GOVERNOR
Also called as SPEED LIMITER DEVICE(SLD)ELECTRONIC SPEED GOVERNOR
(ESG)SPEED CONTROL DEVICE (SCD)
![Page 4: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/4.jpg)
DEFINITION
Speed limiting device has primary function to control the fuel feed to the engine in order to limit the speed of the vehicle to a specified value without effecting the other performance parameter of the vehicle .
![Page 5: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/5.jpg)
TYPES OF SPEED GOVERNOR
TYPE PRINCIPLE PERFORMANCE
MECHANICAL Welding of iron strip or bolt just below the accelerator pedal to restricts the engine rpm.
Lack of power Pickup of vehicle falls
drastically.
CABLE MECHANISM
Microcontroller receives the input signal from the speed sensor and send the signal out to the actuator
Actuator cuts the fuel & air intermittently and not let run the engine above prescribed speed.
FUEL MANAGEMENT
Management of calibrated fuel through ECU to control the vehicle speed.
Steady specified speed is achieved without any hiccups ensuring smooth ride.
![Page 6: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/6.jpg)
MAIN COMPONENTS
SPEED SENSOR
ELECTRONIC CONTROL UNIT
ACTUATORS
WIRING HARNESS
![Page 7: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/7.jpg)
SPEED SENSOR
REED SWITCH TYPE – redundant/non reliable technology
HALL EFFECT TYPE – latest / reliable technology
![Page 8: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/8.jpg)
HALL EFFCT SENSOR
The Hall element is a small semiconductor plate when a current is pass through it in the presence of magnetic field generate voltage . This voltage is proportional to current and the magnetic field. This generation of voltage is called Hall effect.
Hall Effect Sensor
![Page 9: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/9.jpg)
ELECTRONIC CONTROL UNIT
This is an electronic circuit contains an array of resistance and capacitors with a 32 bit microcontroller, where all the input signal are analyzed and passing through the whole algorithms of software then a suitable out put is generated for final control elements called Actuator.
![Page 10: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/10.jpg)
Actuators
The actuator is a translation of the converted controlled signal in to action .
It is an energy conversion device having an electrical input as signal and force and displacement as an output.
Mechanical
Electrical Solenoid
![Page 11: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/11.jpg)
TEMPER PROOFNESS
Vehicle speed should not cross the set speed if any of the below condition occurred.
If sensor is bypassed If ECU is bypassed If wiring is bypassed If complete system is
bypassed
![Page 12: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/12.jpg)
MECHANISM OF CABLE TYPE SPEED LIMITER
![Page 13: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/13.jpg)
Regulation of speed of vehicles
Motor Vehicle Act , 1988 Sections 183,112,184,66
Central Motor Vehicle Rules, 1989 , Rule 118 Delhi Gazette Notification F. No
PCO/STA/II/2001PF-2/194 Dated 24 February 2003 & subsequent guidelines dated 17-02-2007
SLD Standards AIS 018, IS :10250, IS : 9000
![Page 14: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/14.jpg)
REGULATION /ENFORCEMENT ON ROADS
In no case transport vehicle should run above 40 kmph in Delhi roads.
ESG should not be tempered .Seals of ESG should be intact.ESG should not be removed .Annual Maintenance Contract /History
card should be kept along the vehicle documents.
![Page 15: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/15.jpg)
MAINTENANCE OF ESG
Quarterly calibration and maintenance services are mandatory.
No road side mechanic /unauthorized technicians are allowed to repair the ESG.
In case ESG defective the vehicle is not allowed to ply on hire – reward purpose.
The operator / driver may get repairs/correction from authorized dealer workshops.
![Page 16: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/16.jpg)
ECU
Gear BoxEngine
Actuator Motor
Accelerator Pedal
Location inside driver cabin
Location Inside cabin or under chasses.
Electronic sensor cable
Speed sensor
Accelerator linkages
Sealing locations
![Page 17: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/17.jpg)
ECU
Gear BoxEngine
Actuator Motor
Accelerator Pedal
Location inside driver cabin
Location Inside cabin or under chasses.
Electronic sensor cable
Speed sensor
Accelerator linkages
By pass switch
Electronic By-passing with intact seals
![Page 18: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/18.jpg)
Main seals are located at the sub - assemblies i.e. speed sensor, ECU & Actuator Motor
The other seals are fixed at accelerator linkages depending upon model of ESG & vehicle which can be additional one or two.
The possibility of electronic tempering may not be ruled out even the seals are intact, if the insulation of the sensor pulse wire is sheared off and the earthed with the help of shunt (additional piece of wire) and with the help of a switch located at convenient reach of driver.
The driver can by-pass the speed governor and the vehicle speed can shoot up to his desire.
In case some other tempering is carried out the chances of SLD at working mode will not be possible and will damage the electronic components.
Tempering of the SLD
![Page 19: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/19.jpg)
SEAL LOCATIONS - a
At gear box / speed sensor
![Page 20: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/20.jpg)
SEAL LOCATION -b
At ECU
![Page 21: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/21.jpg)
SEAL LOCATION- c
At throttle / linkages
![Page 22: A Familiarization to Speed Governor Anil Chhikara Motor Licensing Officer Transport Department GNCT, Delhi](https://reader036.vdocuments.net/reader036/viewer/2022062304/56649d085503460f949d9f83/html5/thumbnails/22.jpg)
THANKING YOU