a great plains...introduction your great plains folding drill is designed to give you many years of...

© Copyright 1998 Printed 1182

(ORANGE)

Operator's/Parts Manual

24' & 30' 2-Section Drill 1982

Great Plains Manufacturing, Inc. RO. Box 5060 • Salina, Kansas 67402-5060

A Read the operator's manual entirely. When you see this symbOl, the subsequent in~ .. structions and warnings are serious" follow without exception. Your life and the lives of

others depend on it!

Great Plains

155-0560

3) GREAT PLAINS/2-SECTION DRILLS/2-SECTION CONVENTIONAL DRILLS

INTRODUCTION

Your Great Plains Folding Drill is designed to give you many years of dependable service. This Manual has been prepared to instruct you in the safe and efficient operation of this machine. Read and study it thoroughly. Follow all instructions and service procedures carefully.

Should your Grain Drill require replacement parts, go to the Great Plains Dealer. That way you will be sure you are getting the proper parts.

It is important you complete and send in your Warranty card because it is not valid unless it is on file at Great Plains. If you need information not contained in this Manual, contact your Great Plains Dealer.

Thank you for buying a Great Plains Folding Drill.

OPERATING CHECK LIST

Roy Applequist President

Before operating your Drill for the first time, make sure you have checked the following items: D 1. Read operating instructions.

D 2. Read "Safety Rules'; Page 16.

D 3. Check machine for loose bolts, set screws, pins and chains. D 4. See that all tires have proper air pressure.

D 5. Lubricate Drill. D 6. Inspect feeder cups for foreign matter. D 7. Rotate each gauge wheel to see that the drive system is operating smoothly.

D 8. Check for leaks in the hydraulic system.

Great Plains SOLID STAND

FOLDING DRILL Effective 1-82

Operating Instructions Pg.

Introduction .................................................................... 1 Operating Check List ............................................................. 1 Tractor Hook-up .........................•.••...•.•............................. 2 Transporting ...................................•....................... : . . . . . . . 3 Unfolding ..................••..........•.•......................••.........•.. 3 Folding .....................•.................•......... : . . . . . • . • . .... . . . . . . . . . 3 Drilling Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • . . 4 Leveling the Drill . . . . . . . . . . . . . . . . . . . . . . . . . • . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Transport Wheel Adjustments for Leveling and Depth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Gauge Wheel Adjustmentfor Leveling and Depth .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Individual Opener Adujustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . • . . . . 6 Press Wheel Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Seeding Adjustments ..... . . . . . . . . . . . . . . . • . . . . . . . . . . . . . . . . . . . . . . . . . • . . . . . . . . . . . . . 8 Seed Rate Charts ............................................................... 9 Sprocket Arrangements for Drive Types ..........................•................... 12 FieldOperations . .. .. .... . . . . . . . . .. . ... ... . .. .. . . . . . . . . ..... . ... ....... . . . .. .. .. 13 Maintenance Service ............................................................ 13 TroubleShooting... .. .... . . ... . . .. . . . .. ... . . . .. .. . . . . . .... . ..... .. .... ... . .. .. .. 14 Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Optional Equipment ............................................................ .

Parts Drawings

Drill Overview Tongue and Pull Bars .............................................•............... Boxes and Frame, 24'Drill ........................................................ . Boxes and Frame, 30' Dri II ........................................................ . Mainframe, Slide and Transport Axle ................................................ . Pivot Post Assembly ................................................•............ Lift and Slide Hydraulics ..............................•.............•............. Wing Hydraulics ................................................•.••............ Lid "nd Steps ............................................................... .. . Feeder Cup Channel Assembly ............•...........................•............ Gauge Wheel Drive ...........................•.....................•............ GaugeWheel-Non-Drive .............................. , ............•............ Single Disk Opener .......•........................................•............. Double Disk Opener ...•.......•................ . . . . . . . . . • . . . • . . . . . • • . . .....•.... Press Wheel Assembly-2"x 13"Single ...•..............•...•....................... Press Wheel Assembly-2" x 13" Double ''V'' ......................................... . Press Wheel Assembly-4" x 12"V-Groove ..............••...•....................... Rubber-Tired Depth Control Wheel .....•...............•............................ Outside Double-Disk Scraper ..................................................... . Folding Hydraulic Marker ...........................................•............. Marker Hydraulics .............................................................. . Grass Seeder Attachment ............................•............................

18 19 21 22 23 25 26 27 28 30 33 35 36 38 40 41 43 44 45 46 48 49

Figure 1 Single Strap Hitch

Figure 3 Vertical Position

TRACTOR HOOK·UP

Figure 2 Clevis Hitch

FIgure 4 Horizontal Transport

Position

1 . The combination hitch can be used as either a single strap or clevis hitch as shown in figures 1 and 2. The bolt holes in the hitch have been offset vertically so the hitch can be turned over and bolted ·at two height locations on the tongue.This makes it possible to have four hitch heights for both the single strap and the clevis hitch. HITCH HEIGHT SHOULD BE SET SO TONGUE OF DRILL IS PARALLEL TO THE GROUND WHEN DRILLING.

2 . The tongue jack makes it possible to raise or lower the hitch as needed for tractor hook-up. Always return jack to its horizontal storage position on top of tongue slide before folding drill (see fig. 3 and 4).

3. Once you have the hitch pin in place (1" DIA. MINIMUM SIZE PIN) and the jack in storage position, you are ready to hook up your hydraulic hoses. You need a dual hydraulic system. If this is the first time you have had fluid in the systems, you should use the following procedure:

a. Hook Hydraulic hoses to tractor outlet. b. Loosen both connections on one cylinder. c. Slowly work hydraulic lever back and forth. d. When fluid begins to come out of one hose, tighten that connection. e. When fluid begins to come out of the other hose, tighten that connection. f. Repeat above process on each cylinder. g. Check tractor hydraulic reservoir fluid level at this time. You will probably have to add some hydraulic flUid.

(See detailed drawings of hydraulic system in Parts Manual.)

4. If wing cylinders do not operate properly, clean out small orifice in fittings circled on wing cylinder illustration (see fig. 5).

Figure 5 Wing Hydraulics

2

I

(

(

(

TRANSPORTING

Before tranSP9rting the drill, you should always check the following items: ,

Pins in Transport Position

Figure 6 Figure 7 1. To prevent possible damage in case of hydraulic failure 2. Check to be sure the pull.tJar transport lock pin is in

during transport, ALWAYS insert safety lock pins position as shown in figure 7 to insure boxes will not when transporting (see fig. 6). open during transport.

3. Check to see if you have the required 60 Ibs. of pressure in the four transport tires (Gauge wheel tires should have 45lbs.~

4. Do you have the proper highway warning devices to satisfy all federal, state and local highway safety laws?

CAUTION: THIS DRILL SHOULD NEVER BE PULLED FASTER THAN 20 MILES PER HOUR.

UNFOLDING

1. Remove pin from pull·bar transport lock (see fig. 7). This must always be used when moving the drill in folded position.

2. Unfold boxes using hydraulic cylinders. Do this very slowly and carefully. Serious damage could occur if done fast and carelessly. Folding and unfolding is best achieved on level ground.

3. Apply hydraulic pressure to the raising and lowering system. Raise the drill to free up the transport lock pins for removal (see fig. 6). Place pins into storage position (see fig. 8).

FOLDING

1. To fold the drill, reverse the order of the unfolding instructions. Be sure all transport devices as shown in figures 6 and 7 are in place before transporting.

2. When folding the boxes, the pull bar brackets should slide smoothly together into the stabilizer wing on the tongue (see fig. 10). If they scrape the wing, the boxes can be raised or lowered by adjusting the wing turnbuckle (see fig. 9).

Figure 10

3

blJ¢ 3d ,~ ."Y

Pins in Storage -.J!!'l!!!IIIIIII.lI!II!.~ Position

Figure 8

Figure 9

Wing Adjustment Clevis

DRILL ADJUSTMENTS

Place the drill on a level seedbed typical to your planting soil and unfold the boxes.

At the top of both vertical tubes on the transport frame is a threaded stud and jam nut (see fig. 11). Make sure both studs have approximately the same length of threads extending above the jam nut (5 inches) to insure that the lift. cylinders can fully retract.

PUT THE TRANSPORT PINS IN STORAGE POSITION (see fig. 8). Slowly lower the drill until it is firmly on the ground and FULLY EXTEND THE TOP SLIDE CYLINDER (see fig. 12). Pull the drill forward a few feet to make sure that the transport and the gauge wheel tires have equal firm contact with the ·soil.

Figure 11 Threaded Stud

Figure 12

Leveling the Drill Top Slide Cylinder

The opener spring rods located along the back of the drill boxes are indicators of the level of the drill because they show the amount of down-pressure exerted on the disk openers. A level drill will have equal opener down-pressure from end to end. Check the spring rod cross bolts to see that they are all extending about 1 to 2 inches above their spring rod castings (see fig. 13). This is a general dimension and may vary with the spring down-pressure you require for different soil conditions and planting depths (see Opener Depth Adjustments).

If all the spring rods along the drill extend the same distance above their castings, the drill is level and you should tighten down the threaded studs as described in ''Transport Wheel Adjustments for Leveling and Depth" on page 5. If the spring rod extensions vary in length, the drill can be leveled with transportwheel and gauge wheel adjustments. These are described on page 5.

NOTE: Transport wheel and gauge wheel adjustments for leveling the drill raise or lower the drill box, causing opener and seed planting depth changes at the center and ends of the drill. For individual disk opener adjustments see page 6.

4

Figure 13 Opener Spring Rods

(

(

(

Transport Wheel Adjustments for Leveling and Depth

When leveling your drill, opener spring rods near the center of the drill that extend higher above their spring rod castings than desired can be adjusted by raising the transport frame. This is done by raising the drill with the hydraulic lift cylinders. Spring rods near the center that don't extend high enough are adjusted by lowering the transport frsme (raising the transport wheels by retracting the cylinders). ONCE THE SPRING RODS AREATTHE DESIRED SETIlNG, screw the threaded studs on top of the vertical tubes (see fig. 11) down as far as possible and secure them with the jam nut. This adjustment will stop the lift cylinder travel at the same point each time the boxes are lowered for drilling and assures accurate seed depth control.

t s~:g __ ~\ -------I~r-------.....,J !.evel UIU ~I~ ~m m~ m~ OlD

Gauge Wheel Adjustment for Leveling and Depth

The openers near the outside of the drill are adjusted by raising or lowering the gauge wheels. Raise the drill out of the ground and loosen the jam nut located near the bottom clevis of the gauge wheel adjustment arm (see fig. 14). This arm is

( threaded to allow easy opener seed depth adjustment. By lengthening the \ arm the gauge wheel is lowered, causing less penetration of the openers and

less spring rod extension for leveling. By shortening the arm the gauge wheel is raised, causing deeper penetration of the openers and the spring rods will extend higher. After adjusting, be sure the arms on both gauge wheels have the same length of threads showing.

s~:g_,-=I ====~I\ \ Level ~ Ilf UIU om L:u II;;;;) lIllJ:;::=:======n~TIFIIJ

5

Retracting the main lift cylinders will level the center of the drill with the ends

Figure 14 Gauge Wheel Adjustment Arm

Shortening the gauge wheel adjustment link will level the ends of the dri II with the center

INDIVIDUAL OPENER ADJUSTMENTS

Press Wheel-Opener Unkage Depth Adjustment

When using the press wheels as rigid-mount depth control wheels, the depth of each opener is controlled by the position of the press wheel. There are several holes on the press wheel spring rod for varying the height of the press wheel. By removing the adjustment pin and raising thE!" press wheel in relation to the opener, deeper penetration is provided (see fig. 15). The press wheel is lowered if less penetration is desired.

Spring Tension Setting

Each opener spring can be adjusted for tension. This is useful when penetrating hard soil and for planting in tractor tire tracks. To adjust the tension, remove the 'W" clip at the bottom of the spring and place it in a higher hole for more tension and in a

''W'' Clip lower hole for less tension (see fig. 16 and 17). If too much penetration is achieved at the lowest tension set-ting, completely remove the "W" clips. Figure 16

Figure 15 Opener Unkage Depth Adjustment

Minimum Tension Figure 17

Maximum Tension

6

(

"W"Clip

(

( 1

PRESS WHEEL ADJUSTMENTS

1. Press Wheel Spring Location

( \ The press wheels are designed to perform two different functions: they can be set as either independent spring.

(

loaded firming wheels or as rigid-mount depth control firming wheels.

To achieve the spring·loaded action, the press wheel spring must be set.below the mounting bar and the cotter pin on top of the bar (see fig. 18). The press wheel spring rod has several holes in it for varying the spring pressure at the press

.. wheel. When using rubber·tired depth control wheels on the opener, the press wheels should always be set for spring. . loaded firming action.

To achieve the rigid-mount depth control action, the cotter pin must be set below the mounting bar with the spring on top. This spring prevents the press wheel from dropping when the drill is raised and provides a place to store the press wheel spring (see fig. 19).

Cotter Pin .... ~ ... =-

Figure 18 Independent

Spring·Loaded Action

"------ (::Otter Pin

Figure 19 Rigid-Mount

Depth Control Action

2. Press Wheel Angle Adjustment (Double-V Press Wheels Only) Adjustment Pin

Figure 20 Figure 21

7

The camber angle of the double-V press wheels may be adjusted by removing the angle bar adjustment pin and moving the angle bar. Moving the angle bar forward will cause the press wheels to pull more soil over the seed (see fig. 2O). Moving the angle bar back will cause the press wheel to pull less soil over the seed (see fig. 21).

SEEDING ADJUSTMENTS

1. Rotate each gauge wheel to see that feed cups and drive are working properly and are free from foreign matter.

2. To adjust your seeding rate, first you must decide which sprocket arrangement you need (see seeding chart). 'In ( order to change sprockets, remove nut in center of double speed change sprocket and tum sprocket over. Loosen the idler arm bolt, put chains on and tighten both bolts. (The chains need to be reversed to make this change.)

3. There are many factors which will affect seeding rates: seed treatment, weight of seed, size of seed, surface condition of seed, and tire configuration, pressure and slippage. Minor adjustments will probably be needed to compensate for the above factors.

4. The pounds-per-acre in the seed charts are based on drills having 9.5L x 15 inch rib implement gauge wheel tires with 45 Ibs. of air pressure.

5. The large differences in seed size and treatment can cause a wide variation in actual seeding rates. The seed rate charts on the following pages are based on average size seed. This may differ from the seed you are using. Use the seed rate charts as a guide. Set the pounds-per-acre desired at the indicator number for your row spacing and complete the following procedure to calibrate the drill for your specific seed.

a. Place several pounds of seed over three of the feeder cups at the outboard end of the drill box.

b. Pull the seed tubes out of these three disk openers. c. Raise the drill off the ground. Be sure to insert transport lock pins in slide tubes to prevent injury should hydraulic

system allow drill to lower while working around it.

d. Place a container under the three seed tubes to gather the seed as it is metered.

e. Rotate the drive gauge wheel until one acre has been tallied on the acremeter. This will be approximately 250 rotations on a 24' drill and approximately 200 rotations on a 30' drill. Be sure to check the three feeder cups to make sure each cup has plenty of grain coming into it

f. Weigh the seed which has been metered. Divide by three. This will give you the ounces/pounds metered by each feeder cup. Multiply by the number of openers on your drill to arrive at the total pounds-per-acre your drill would meter at that setting. If this figure is different than desired, set your feed cup adjustment lever accordingly.

Repeat procedures a through! on each drill section. 6. You may want to repeat the calibration procedure if the results of your calibration vary greatly from the suggested

settings contained in this manual.

Remember: Tire size and field conditions will also affect seeding rates. Be certain that your gauge wheel tires are 9.5L x 15 and that they are inflated to 45lbs. When drilling, check the amount of seed you are using by noting acres drilled, amount of seed added to drill, and level of seed in drill box. If you suspect that you are drilling more or less seed than desired, and you have accurately calibrated the drill to your seed, you may need to adjust the seeding rate slightly to compensate for your field conditions.

8

(

(

Seeding Rates

WHEAT SEED RATE INDICATOR SETTING NUMBER (DRIVE TYPE 1) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 60 85 90 95 100 Row Spacing Lbo. Per Acre

6' 0 2 15 25 36 48 62 73 86 98 113 125 140 152 186 183 199 217 221 229 230 r 0 1 13 22 31 41 52 62 73 84 96 106 119 129 143 156 169 165 188 194 196 7~' 0 1 12 20 29 39 49 59 69 79 90 100 118 121 134 147 159 174 177 183 184 8' 0 1 12 19 27 36 48 65 84 74 84 94 105 114 126 138 149 163 186 172 173

10' 0 0 9 15 22 29 37 44 52 59 88 75 84 91 101 110 119 130 133 137 138 12' 0 0 8 13 18 24 31 37 43 49 56 63 70 76 84 92 99 109 111 114 115

RICE SHORT GRAIN SEED RATE INDICATOR SETTING NUMBER (DRIVE TYPE 1) 0 5 10 15 20' 25 30 35 40 45 50 55 60 65 70 75 60 65 90 95 100 Row Spacing Lbo. Per Acre '.

6' 0 3 12 19 27 36 44 53 61 70 78 87 97 104 112 119 128 135 138 138 141 7" 0 2 10 16 23 31 38 45 52 59 67 74 83 89 95 101 108 115 118 118 120 n" 0 2 9 15 21 29 35 42 49 56 63 70 78 83 90 95 102 108 111 111 113 8" 0 2 8 14 20 27 33 39 48 52 59 65 73 78 84 89 96 101 104 104 106

10" 0 1 7 12 16 22 27 32 37 42 47 52 56 63 67 72 77 81 83 83 65 12" 0 1 6 10 13 18 22 26 31 35 39 44 49 52 56 60 84 88 69 69 70

RICE SHORT GRAIN SEED RATE INDICATOR SETTING NUMBER (DRIVE TYPE l·A) 0 5 10 15 20 25 30 35 40 45 50 65 60 65 70 75 60 8S 90 95 100

Row Spacing Lbs. Per Acre 6" 0 6 20 36 52 65 86 103 120 136 156 175 203 219 233 250 272 288 294 298 300 r 0 5 17 31 44 55 73 87 102 118 135 149 173 186 198 213 231 245 250 254 255 7~" 0 4 16 29 41 52 69 82 96 111 127 140 163 175 187 200 217 231 235 239 240 8" 0 4 15 27 39 49 84 77 90 104 119 131 153 184 175 186 204 216 221 224 225

10" 0 3 12 22 31 39 52 62 72 83 95 105 122 132 140 150 163 173 177 179 180 12" 0 2 10 18 26 33 43 51 80 69 79 88 102 110 117 125 136 144 147 149 150

RICE LONG GRAIN SEED RATE INDICATOR SETTING NUMBER (DRIVE TYPE 1) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 65 90 95 100

Row Spacing lbs. Per Acre 6" 0 1 8 16 24 35 43 50 80 88 75 83 69 96 102 107 115 123 123 124 126 7" 0 1 7 14 21 30 37 43 51 57 84 70 76 81 86 91 98 104 104 106 107 n" 0 1 6 13 19 28 34 40 48 54 60 66 71 77 81 86 92 98 98 99 101 8" 0 1 6 12 18 26 32 38 45 51 56 62 67 72 76 80 86 92 92 93 94

10" 0 0 5 10 15 21 26 30 36 41' 45 50 54 56 61 64 69 74 74 75 76 12" 0 0 4 8 12 18 22 25 30 34 38 41 45 48 51 54 56 61 61 62 63

RICE LONG GRAIN SEED RATE INDICATOR SETTING NUMBER (DRIVE TYPE l·A) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100

Row Spacing lbs. Per Acre 6" 0 3 12 28 47 84 81 101 117 129 151 169 185 196 213 226 242 262 268 272 273 7" 0 2 10. 24 40 55 69 86 99 110 128 144 157 167 181 192 205 222 226 231 232 ~" 0 2 9 23 37 51 65 81 93 103 121 135 148 157 171 181 193 209 215 217 218 8" 0 2 9 21 35 48 61 76 88 97 113 127 139 147 160 169 181 196 201 204 205

10" 0 1 7 17 28 39 49 61 70 78 91 102 111 118 128 138 145 157 161 163 164 12" 0 1 6 14 23 32 40 50 58 65 75 85 93 98 107 113 121 131 134 136 137

BARLEY SEED RATE INDICATOR SETTING NUMBER (DRIVE TYPE 1) 0 5 10 .15 20 25 30 35 40 45 80 55 60 65 70 75 80 8S 90 95 100

Row Spacing Lbs. Per Acre

6" 0 0 11 19 27 35 43 51 58 66 74 82 90 98 106 114 121 129 137 145 151 7" 0 0 9 16 23 30 36 43 50 57 63 70 77 84 90 97 104 111 117 124 130 n' 0 0 8.5 15 21 28 34 40 47 53 59 86 72 79 85 91 98 104 110 117 121 8" 0 0 8 14 20 26 32 38 44 50 56 62 86 74 80 86 92 98 104 110 116

10" 0 0 7 11 16 21 26 30 35 40 45 49 54 59 84 86 73 7B 83 88 93 12" 0 0 6 10 14 18 22 26 29 33 37 41 45 49 53 57 60 64 86 72 76

SAFFLOWER OR OATS SEED RATE INDICATOR SETTING NUMBER (DRIVE TYPE 1) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 Row Spacing Lbs. Per Acre

6" 0 0 7 14 22 29 37 45 53 62 71 63 87 98 104 113 123 134 147 150 " 156 7" 0 0 6 12 18 24 32 38 45 53 60 71 74 84 88 96 lOS 114 125 128 132 n:" 0 0 5 11 17 23 30 38 43 50 57 67 69 79 83 91 99 107 118 120 125

( 8" 0 0 5 10 16 22 28 33 40 47 53 63 65 74 78 85 93 101 110 113 117

10" 0 0 4 8 13 17 22 27 32 37 43 50 52 59 62 66 74 81 88 90 93 12" 0 0 3 7 11 14 19 22 27 31 35 42 43 49 52 57 62 67 74 75 78

RYE SEED RATE INDICATOR SETTING NUMBER (DRIVE TYPE 2) 0 5 10 15 20 25 30 35 40" 45 50 55 60 85 70 75 80 85 90 95 100 Row Spacing -- Lbs. Per Acre

6" 0 0 4 8 12 15 18 21 28 30 33 38 41 45 48 53 66 62 63 68- 69 7" 0 0 3 7 10 13 16 1S 24 25 2S 32 35 38 41 45 49 53 54 57 58 n" 0 3 6 9 9 12 15 17 23 24 27 30 33 38 39 42 48 50 51 54 54 8" 0 0 3 6 9 11 14 16 21 22 25 28 31 34 36 40 43 47 4B 51 52

10" 0 0 2 5 7 9 11 13 17 18 20 23 25 27 29 32 35 37 38 41 42 12" 0 0 2 4 6 S 9 11 14 15 17 19 21 23 24 26 29 31 32 34 35

MILLET SEED RATE INDICATOR SETTING NUMBER (DRIVE TYPE 2) 0 5 10 15 20 25 30 35 40 45 50 55 60 85 70 75 80 85 90 95 100 Row Spacing Lbs. Per Acre

6" 0 2 6 9 12 15 18 22 24 2S 33 38 43 48 50 55 61 67 69 70 71 7" 0 1 5 7 10 13 16 18 21 24 28 32 38 39 43 47 52 57 59 60 61 7%" 0 1 4 6 9 12 15 17 19 23 27 30 34 37 40 44 49 53 55 58 57 8" 0 1 5 7 9 11 14 16 18 21 25 28 32 34 38 42 46 50 52 53 54

10" 0 0 4 5 7 9 11 13 15 17 20 23 26 28 30 33 37 40 42 43 44 12" 0 0 3 4 6 S 9 11 12 14 17 19 21 23 25 26 31 33 35 36 37

BUCKWHEAT SEED RATE INDICATOR SETTING NUMBER (DRIVE TYPE 1) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 65 90 95 100 Row Spacing Lbs. Per Acre

( 6" 0 4 13 22 31 41 52 62 66 63 94 106 112 124 135 152 166 183 195 196 200 7" 0 4 11 19 27 35 44 53 57 71 80 90 95 106 114 129 141 156 166 167 170 T'k" 0 3 10 1S 25 33 41 50 54 67 75 65 89 99 lOS 122 133 147 156 157 160 8" 0 3 10 17 23 31 39 47 51 83 71 80 84 93 101 114 124 138 148 147 150

10" 0 3 8 13 19 25 31 37 41 50 57 84 67 75 81 91 100 110 117 11S 120 12" 0 2 7 11 16 20 26 31 34 42 47 53 66 62 67 76 83 92 96 99 100

FLAX OR SUDAN SEED RATE INDICATOR SETTING NUMBER (DRIVE TYPE 2) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 65 90 95 100 Row Spacing Lbs. Per Acre

6" 0 2 4 7 10 14 17 20 25 28 32 38 39 42 45 50 55 59 63 65 66 7" 0 1 4 6 8 12 15 17 21 24 27 31 33 38 38 42 47 50 53 58 57 n" 0 1 3 5 7 11 14 16 20 22 25 29 31 34 36 40 44 47 50 52 54 8" 0 1 3 5 7 10 13 15 19 21 24 27 29 32 34 37 41 44 47 49 51

10" 0 0 3 4 6 S 10 12 15 17 19 22 23 25 27 30 33 38 38 39 41 12" 0 0 2 4 5 7 9 10 13 14 16 18 19 21 23 25 28 30 32 33 34

SUNFLOWERS SEED RATE INDICATOR SETTING NUMBER (DRIVE TYPE 2) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 B5 90 95 100 Row Spacing Lbs. Per Acre

6" 0 0 0 3.8 7.6 112 15 la8 22.6 26 32 38 41 45 49 53 58 60 84 66 72 7" 0 0 0 32 6.4 9.6 12.8 16 19 22 27 32 35 38 41 45 46 51 54 57 60 7%" 0 0 0 3 6 9 12 15 18 21 25.5 30 33 36 39 42 45 48 51 54 57 8" 0 0 0 2.8 5.6 8.5 11.3 14 17 20 24 28 31 34 37 39 42 45 48 51 54

10" 0 0 0 2.3 4.5 6.8 9 11 13.5 16 19 23 25 27 29 32 34 36 38 41 43 12" 0 0 0 1.9 3.8 5.6 7.5 9.9 11.3 13 16 19 21 23 25 27 28 30 32 34 38

(

{

\.

SOYBEANS SEED RATE INDICATOR SETTING NUMBER (DRIVE TYPE 1) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 60 85 90 95 Row Spacing Lhs. Per Acre

6" 0 0 0 20 25 43 63 75 87 102 123 137 152 170 183 197 207 233 235 237 7" 0 0 0 17 21 37 54 63 74 86 104 116 129 144 156 167 176 198 199 201 7~" 0 0 0 16 20 35 51 60 69 81 98 109 121 136 147 157 165 187 186 169 8" 0 0 0 15 18 33 48 56 65 76 92 103 114 127 136 148 155 175 176 178

10" 0 0 0 12 15 26 36 45 52 61 74 .82 91 102 110 118 124 140 141 142 12" 0 0 0 10 12 22 32 37 43 51 61 68 76 85 92 98 103 117 117 118

- SOYBEANS SEED RATE INDICATOR SETTING NUMBER (DRIVE TYPE 2) 0 5 10 15 20 26 30 35 40 45 50 55 60 65 70 75 60 85 90 95

Row Spacing Lbs. Per Acre 6" .. 0 0 0 7 8 15 21 24 29 33 40 45 51 55 62 65 71 76 77 78 7" 0 0 0 6 7 13 18 20 24 28 34 36 43 47 52 55 61 65 86 67 7~" 0 0 0 5 6 12 17 19 23 27 32 36 41 44 49 52 57 61 62 62 8" 0 0 0 5 6 11 16 18 22 25 30 34 36 41 46 48 63 57 58 58

10" 0 0 0 4 5 9 13 14 17 20 24 27 31 33 37 39 43 46 46 47 12" 0 0 0 3 4 8 10 12 14 17 20 23 26 28 31 32 36 38 39 39

SOYBEANS SEED RATE INDICATOR SETTING NUMBER (DRIVE TYPE 2·A) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 60 85 90 95

Row Spacing Lbs. Per Acre 6" 0 0 0 0 20 32 43 46 58 73 87 98 100 112 118 123 136 149 150 153 7" 0 0 0 0 17 27 37 41 50 62 74 63 85 95 101 105 115 127 128 130 7~" 0 0 0 0 16 25 35 39 47 59 69 78 80 69 95 99 109 119 120 123 8" 0 0 0 0 15 24 33 38 44 55 65 73 75 84 69 93 102 112 113 115

10" 0 0 0 0 12 19 26 29 35 44 52 59 60 67 71 74 82 90 91 92 12" 0 0 0 0 10 16 22 24 29 37 43 49 50 56 59 62 68 75 76 77

Setting the feed cup adjustment lever between 50 and 80 allows for optimum seedmg of soybeans. These charts are computed with 2600 soybeans/Jb seed size

PEAS SEED RATE INDICATOR SETTING NUMBER (DRIVE TYPE 1) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 60 85 90 95

Row Spacing Lbs. Per Acre 6" 0 0 7 23 28 48 61 78 95 113 129 146 164 160 198 215 228 244 245 246 7" 0 0 6 20 24 41 52 67 81 96 110 128 140 153 186 183 194 205 209 210 7%" 0 0 5 19 22 38 50 63 76 90 103 118 131 144 158 172 182 196 196 197 8" 0 0 5 18 21 38 46 59 72 64 97 111 123 135 148 161 171 183 164 165

10" 0 0 4 14 17 28 37 47 57 68 78 89 99 108 119 129 137 147 148 149 12" 0 0 3 12 14 24 31 39 48 58 65 74 62 90 99 108 114 122 123 124

PINTO BEANS SEED RATE INDICATOR SETTING NUMBER (DRIVE TYPE 2) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95

Row Spacing Lbs. Per Acre 6" 0 0 0 0 2 3 7 12 17 24 29 40 45 48 54 61 71 73 75 76 7" 0 0 0 0 2 3 6 11 16 22 27 34 38 41 46 52 61 62 64 65 7%" 0 0 0 0 1 2 5 10 15 21 26 31 38 39 43 49 ··57 59 60 61 8" 0 0 0 0 1 2 5 9 14 19 25 30 34 38 41 46 53· 55 56 57

10" 0 0 0 0 0 2 4 8 13 18 20 24 27 29 33 37 43 44 45 46 12" 0 0 0 0 0 1 3 7 12 16 17 20 23 24 27 30 38 37 38 38

RAPE OR ALFALFA SEED RATE INDICATOR SETTING NUMBER (DRIVE TYPE 2) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 Row Spacing Lbs. Per Acre

6" 0 2 5 8 11 13 17 21 24 31 31 35 40 44 46 52 53 65 62 65 7" 0 2 4 6 9 11 14 18 20 28 27 30 34 37 41 44 45 47 52 55

n' 0 1 3 6 8 10 13 17 19 25 25 28 32 35 39 42 43 44 49 52 8" 0 2 4 6 8 10 13 16 18 23 24 27 30 33 38 39 40 41 46 48

10" 0 1 3 5 7 8 10 13 14 19 20 21 24 26 29 31 32 33 37 39 12" 0 1 3 4 5 7 8 11 12 15 16 18 20 22 24 26 27 28 31 32

11

100

242 205 193 181 145· 121

100

79 68 63 59 48 40

100

159 135 127 119 95 79

100

247 211 198 186 150 125

100

60 67 63 59 46 40

100

68 56 53 49 40 33

MILO SEED RATE INDICATOR SETTING NUMBER

(DRIVE TYPE 2) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 60 65 90 95 100 Row Spacing lbs. Per Acre (

6" 0 2 5 8 12 15 18 23 28 29 34 40 41 45 49 52 55 65 66 67 66 7" 0 1 4 7 10 13 15 19 23 24 29 34 35 38 41 44 47 55 56 57 56 7%" 0 1 4 6 9 12 14 18 22 23 27 32 33 38 39 41 44 52 53 54 55 8" 0 1 3 6 9 11 13 17 21 22 25 30 31 34 37 39 41 48 50 51 52

10" 0 0 3 5 7 9 11 14 17 18 20 24 25 .27 29 31 33 39 40 41 42 12" 0 0 2 4 6 8 9 11 14 15 17 20 21 23 24 26 28 32 33 34 35

WHEAT GRASS SEED RATE INDICATOR SETTING NUMBER

(DRIVE TYPE 2) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 65 90 95 100 Row Spacing Lbs. Per Acre

6" 0 0 0 1 3 3 4 5 5 8 8 9 9 10 ·10 10 11 11 12 13 13 7" 0 0 0 1 2 3 3 4 4 6 7 7 8 9 9 9 9 10 10 11 11 7%" 0 0 0 0 2 3 3 4 4 6 6 7 7 8 8 8 9 9 9 10 11 8" 0 0 0 0 2 3 3 3 4 6 6 7 7 8 8 8 8 8 9 9 10

10" 0 0 0 0 2 2 2 3 3 5 5 5 6 6 6 6 7 7 7 8 8 12" 0 0 0 0 2 2 2 2 3 4 4 4 5 5 5 5 5 6 6 6 7

Sprocket Arrangements for Drive Types:

39 Teeth ,t= 19 Teeth

I

( 20 Teeth • ~~35Teeth 20 Teeth -35 Teeth

I

Type 1 Type l-A

39 Teeth 19 Teeth , iF= I

35 Teeth -20 Teeth 35 Teeth t P ""'-20Teeth

I Type 2 Type2-A

AELD OPERATIONS

1 . Load seed box with seed. You should use cleaned seed to get the best results. You should always have the drill hitched securely to a tractor before loading.

2 . This machine can be transported with a full box of grain. It is best NOT to do this unless necessary because the increased weight does incresse the chances for problems on the road. DO NOT exceed 20 miles per hour .

. , 3. Never back up with openers in ground. If you do, check all openers to be sure none are clogged.

4. Never allow anyone to ride on the machine.

5. Maximum drilling speed varies upon soil conditions. 6. If your drill comes equipped with an acremeter it should be mounted to the left gauge wheel. It will accumulate the

total acres drilled with the machine. In order to find out the acres covered, write down the beginning reading and subtract it from the ending reading for the total acres planted.

7. You can adjust the tension on each disk spring. This is especially useful in applying more pressure in tractor tracks.

MAINTENANCE SERVICE

PROPER SERVICING AND ADJUSTMENT IS THE KEY TO THE LONG UFE OF ANY FARM IMPLEMENT. WITH CAREFUL AND SYSTEMATIC INSPECTION OF OUR GRAIN DRILL, YOU CAN AVOID COSTLY MAINTENANCE, TIME AND REPAIR.

1. After using your drill for several hours, check all bolts to be sure they are tight. 2. Lubrication-listed below are the items you need to lubricate every 12-15 hours of operation:

a. Gauge wheel bearings. b. Jack shaft bearings. c. Feeder cup drive sprocket bearings. d. Oil all roller chains. This is important to do before putting the machine in storage. e. Feeder cup drive sprocket should be oiled in its square bore. Move feeder cup adjustment lever away from the

sprocket as far as possible in order to get the oil back into the square. This is most important to do before putting the machine in storage.

f. Post top roller shaft. g. Box post lower spindle and cross tube on main frame_ h. Telescoping axle tube lower roller between transport tires. i. Telescoping axle top rollers located inside at top of vertical tube on trsnsport frame (drill must be lowered to reach

lube fitting).

3. Disk scrapers should be kept properly adjusted. 4. Always maintain 45 Ibs. of air pressure in gauge wheel tires and 60 Ibs. in the transport tires.

13

PROBLEM 1. Uneven seed spaci ng or uneven

stand

TROUBLE·SHOOTING

SOLUTION a. Check for trash in seed cup.

b. Check to see if seed tubes are plugged. c. Reduce ground speed. d. Check opener disks to see that turn freely.

e. Use faster drive speed (See page 8, No.2) and close feed cup flutes to a more narrow position.

2. Opener disks not turning freely. a. Check for trash or mud build-up on disk scraper. Readjust scraper.

3. Actual seeding rate is different than desired.

4. Excessive seed cracking

5. Acremeter doesn't measure accurately

6. Uneven seeding depth

7. Press wheel not compacting the soil as desired.

8. Grain box not emptying evenly

b. Check to see if scraper is adjusted too tight and is restricting disk movement.

c. Check disk bearings and flanges.

d. Check opener frame for possible damage.

e. If opener disks turn freely by hand but not in field, lessen down pressure on disk opener. See Operator's Manual, page 6.

a. Check tire pressure. Proper inflation is 45 Ibs. in gauge wheels and 60 Ibs. in transport tires.

b. Check tire size. Proper size is 9.5L x 15. c. Uquid seed treatment will affect seeding rate if the chemicals build up

in seed cup. Unless cleaned regularly, this build up can cause breakage of the feed shaft.

d. Check drive range. See Operator's Manual, page 12.

e. See Operator's Manual, page 8 for instructions on calculating seed rate.

a. Slow drive speed and open flutes in feed cup to a wider position. See page 8, NO.2.

a. Check tire pressure. Proper inflation is 45 Ibs. in gauge wheel tires and 60 Ibs. in transport tires.

b. Check tire size. Proper size is 9.5L x 15. c. Check planting operation for excessive overlap or gaps between passes.

d. Loose soil conditions and slippage will cause variations in acres registered.

e. To check accuracy of acremeter, raise drill out of ground. Note acreage figure on acremeter; rotate the gauge wheel approximately 200 times for a: 30' drill or approximately 250 times for a 24' drill. This should register one acre.

a. Check box leveling adjustments; Operator's Manual, page 4 and 5. b. See depth setting instructions, page 5 and 6.

a Reset press wheel height, page 6 and 7. b. Convert press wheel spring setting to bottom position which gives in·

dependent press wheel action if desired. See Operator's Manual, page 7.

a Certain model drills do not have the same number of seed cups between each divider or bulkhead. The section with the larger number of cups will empty sooner.

b. Check adjustment levers on each box to see that they are set on same indicator number.

(

(

(

( ,

(

PROBLEM 9. Press wheel and opener

plugging

10. Markers (hydraulic) not working properly

11. Rubber tire depth control wheels becoming packed with mud

12. Improper folding of drills

TROUBLE·SHOOTING (Con't)

SOLUTION a. Drilling in damp or wet conditions may increase this problem.

b. Openers may be moved from a staggered to an in·line position to reduce trash thrown from front openers into rear openers.

c. Reduce down pressure on o;:>eners.

a. Check all hose fittings and connections for air and oil leaks. b. Check tractor hydraulic oil level. If conditions persists, have your dealer

service department check sequencing valve.

a Install scrapers. b. Reduce spring tension on openers.

c. Be sure press wheel springs are in independent position. See Operator's Manual, page 7.

a Adjust wing adjusting link as shown on page 3 of Operator's Manual. b. Check hydraulic system for air and oil leaks.

c. Clean out small orifice fittings in wing cylinders. See page 2 of Operator's Manual.

d. Make sure that the wing boxes unfOld to a straight line. Check to see that both pull bars are attached to the boxes at exactly the same distance from the inboard edge of the drill box (90") and that both pull bars are exactly the same length.

15

SAFETY RULES

The safe operation of any machinery is a big concem to farmers and manufacturers. We have designed our Folding Drill with many built-in safety features. However, no one should operate this machine before carefully reading this Operator's Manual. . (

1. Never permit anyone to ride on or walk beside the Grajn Drill when moving.

2. Never permit anyone to ride on tractor when Drill is being moved.

3. Never allow anyone to be near Drill when performing operating functions with the Grain Drill or tractor.

4. Never load Grain Drill without being hooked-up to tractor.

5. Extra care should be taken when transporting with seed in the boxes.

6. Never back Grain Drill up when openers are in ground.

7. Reduce speed when transporting over uneven or rough terrain. Avoid all chuck holes and washboard areas in roads.

8. Reduce speed of tractor when transporting over hills or steep slopes.

9. Always set Grain Drill in field position before lubrication.

10. Do NOT lubricate, adjust or repair the Grain Drill while it is in operation.

11. Comply with all Federal, State and Local Laws when traveling on the highway.

12. Use "Slow MOving Vehicle" emblem for warning vehicles approaching from the rear.

13. Do NOT permit smoking, sparks or an open flame where combustible lubricants or liquids are being used. .

14. When using treated grain, avoid direct contact with the seed.

15. When using compessed air to clean Drill, wear safety glasses.

16. When transporting, remember the Drill is wider than your tractor and extreme care must be taken to allow for safe clearance.

16

(

"

(

(

Warranty

Great Plains Manufacturing, Incorporated warrants to the original purchaser that this grain drill will be free from defects in material and workmanship for a period of one year from the date of original purchase when used as intended and under normal service and conditions_ This Warranty is limited to the replacement of any defective part by Great Plains Manufacturing, Incorporated and the installation by the dealer of any such replacement part: provided that any such defective part is returned to Great Plains within thirty (30) days of the failure_

This Warranty does not apply to any part or product which in Great Plains' judgment shall have been misused or damaged by accident or lack of normal maintenance or care, or which has been repaired or altered in a way which adversely affects its performance or reliability, or which has been used for a purpose for which the product is not designed_ This Warranty shall not apply if the product is towed at a speed in excess of 20 miles per hour.

Claims under this Warranty must be made to the dealer which originally sold the product and all warranty adjustments must be made through such dealer. Great Plains reserves the right to make changes in materials or design of the product at any time without notice_

This Warranty shall not be interpreted to render Great Plains liable for damages of any kind, direct, consequential, or contingent, to property_ Furthermore, Great Plains shall not be liable for damages resulting from any cause beyond its reasonable control. This Warranty does not extend to loss of crops, losses caused by harvest delays or any expense 'or loss for labor, supplies, rental machinery or for any other reason_

No other warranty of any kind whatsoever, expressed or implied, is made with respect to this sale; and al\ implied warranties of merchantability and fitness for a particular purpose which exceed the obligations set forth in this written warranty are hereby disclaimed and excluded from this sale_

This Warranty in not valid unless registered with Great Plains Manufacturing, Incorporated within 10 days from the date of original purchase_

17

(

(

(

c"" .1

Rubber-Tired Depth Control Wheel Installation Instructions

The Rubber·Tired Depth Control Wheel is available for all Great Plains double·disk openers.

1. Slip two carriage bolts '/,;' x 1Y," long through square holes in disk blade. The carriage bolts must enter from the inside of disks to allow proper clearance.

2. Slip depth control wheel over carriage bolts and secure to disk blade with '/,," USS flatwashers, 'hs" lockwashers and 'hs" hex nuts.

3. FOR PROPER DEPTH·CONTROL WHEEL OPER· ATION, OUTSIDE DOUBLE·DISK SCRAPERS ARE REQUIRED. (Part No. 116·019 A)

Independent Spring·Loaded Action

When using rubber-tired depth control wheels on Great Plains Solid Stand" Drills, the press wheel spring and bar should be set for independent spring·loaded firming action.

1. Remove cotter pin, spring rod clip and adjustment pin from spring rod.

2. Remove spring from press wheel assembly.

3. With spring held under mount bar, slip spring rod through spring, and mount bar and insert adjustment pin at desired press wheel setting. Secure with hair pin cotter.

4. Lift spring and insert spring rod clip under spring in desired hole for proper press wheel firming pressure. (Spring is rated at 65 Ibs. per each inch of compres· sian.)

5. Lift press wheel and insert cotter pin on top of mount· ing bar.

Great Plains MANUFAC1URlNG INC. P.O. Box 218 • Assaria,Kansas67416

(

Outside Double-Disk Scraper

Installaiion InsITuciions

NOTE: This scraper is designed to mount on the double-disk openers of any Great Plains grain drill to eliminate mud build-up on the opener and on rubber-tired depth-control wheels. The rubber-tired depth-control wheels should not be used without the outside scraper.

30 Ft. Standard and 30 Fl High Clearance Drills 1. Remove 5/16" x 1" long hex bolts (A). washers and hex nuts which hold existing scraper mount (8) in pos~ion

(see figure 1).

2. Remove inside scraper (C) from scraper mount (8). Scraper mount (B) is no longer ne.eded.

Figure 1 Figure 2

3. Reposition inside scraper (C) onto new scraper mount (D) with 3/8" x 1" long step bolt (E), washers and hex nut (see figure 2).

4. Reattach new scraper assembly to opener frame with 5/16" x 1" long hex bolts (A). washers and hex nuts. BE SURE ANGLE OF NEW SCRAPER MOUNT {D) POINTS INWARD TOWARD CENTER OF OPENER DISK.

5. Install scraper blade (F) on each wing of scraper mount (D) with 5/16" x %" long carriage bolt, washers and hex nut. Adjust scraper blades to have MINIMUM CLEARANCE with disk opener and rubber-tired depth-control wheel.

BE SURE THE DISK OPENER CAN TURN FREELY AFTER INSTALLATION.

Solid Sland'" 3-Point and Solid Stand'" Folding Drills 1. Remove 5/16" x 1 y." long hex bolts (A), washers and hex nuts which hold scraper mounts (B) and press wheel

spring mounting channel (C) in position (see figure 3). . C 2. Remove inside scraper (D) from scraper mount (B). Scraper mount (B) is no longer needed.

Figure 3 Figure 4

3. Reattach inside scraper (D) onto new outside scraper mount (E) with 3/S" x 1" long step bolt (F), washers and hex nut (see figure 4).

4. Reposition new scraper assembly behind press wheel spring mounting channel (C) and attach to opener frame with 5/16" x 114" long hex bolts (A). washers and hex nuts. BE SURE ANGLE OF NEW SCRAPER MOUNT (D) POINTS INWARD TOWARD CENTER OF OPENER DISK.

5. Install scraper blade (G) on each wing of scraper mount (E) with 5/16" x %" long carriage bolt, washers and hex nut. Adjust scraper blades to have MINIMUM CLEARANCE with disk openers and rubber-tired depth-control wheel.

BE SURE THE DISK OPENER CAN TURN FREELY AFTER INST ALLA TION.

Great Plains MANUFAcruRlNG INC. P.O. Box 218 • Assaria,Kansas67416

(

(

c""

W' SOLID STAND® FOLDING DRILL- HYDRAULIC MARKER

Installation Instructions

1. Attach marker mount to lower 3Y," square tube of drill frame using two '!a" x 3%" x 5" long U·bolts, lock· washers and hex nuts (see Figure 1).

2. Determine length of chain necessary to allow 1" to 1%" slack in chain with marker extended horizontally. Make chain length adjustments at turnbuckle.

Hydraulics

Figure 1 '~"

1. Attach selector valve (5) to selector valve mount (6) using two 'Ie" x 2Y," long bolts, lockwashers and hex nuts (see Figure 2). Attach selector valve mount (6) under existing flow divider valve.

Reroute hydraulics as shown in Figure 2.

Attach hose Retainers (14) to drill using opener mount bolts located beneath lower 3%" square tube of drill frame. Route hoses behind frame and on top of double-disk opener U·mount brackets to prevent damage during marker operation.

2

j 3

~ 1-

~ ,

DUAL MARKERS

Ref. Description

5

1 Hydraulic Cylinder, 2" x 8" Single Acting 2 Pipe Swivel, %" MNPT x %" FNPT, 00°, %2" orifice 3 Hydraulic Hose, 24' drill

Hydraulic Hose, 30' drill 4 Service Tee, Y,", Female 5 Double Selector Valve 6 Double Selector Valve Mount 7 Bolt, hex, 'f,"·16 x 2'/," long, Gr. 2

14

/ ./)

I~

2

/ J-, 3-

1-

Figure 2

Ref. Description

8 Lockwasher, J'." 9 Nut, hex, %"·16

10 Fitting, 'f," F swivel x Y," M 11 Hydraulic Hose, y." x 16" long 12 Hydraulic Hose, y." X 42" long

SINGLE MARKER

13 Hydraulic Hose, y." x 303" long (existing) 14 Hydraulic Hose Retainer 15 Slide Cylinder (existing)

Field Operations and Maintenance

1. The double selector valve (Rgure 2, item 5) transfers hydraulic power from the wing cylinders to the marke'r ( cylinders (dual markers only). After your drill boxes have been lowered to field position and locked open, change the selector valve knOb. Hydraulic fluid is transferred to the marker hydraulics and one marker will lower due to no hydraulic pressure on cylinder. Activate your tractor hydraulics lever to lower the other marker and raise the marker that is down. To put the drill boxes in transport position, raise the markers hydraulically, lock into position and change the selector valve knob, transfering the hydraulic pressure to the wing cylinders.

2. The pitch angle of the marker disk may be varied by rotating the marker disk arm. Be sure the set screws are secure before operating.

3. The marker arm is attached to the marker main body with a '(,," shear bolt. If excessive force is put on the marker during operation, the shear bolt will break, allowing the marker arm to swing away rather than cause damage to the marker. Should this occur, replace the bolt with a '(,s" x 1" long, Grade 2 bolt ONLY.

4. The marker has four lubrication fittings. These should be serviced after every 12 to 15 hours of operation to prevent excessive wear.

5. Always operate your marker with safety in mind. Never allow anyone near machinery while in operation.

Great Plains MANUFACTURING INC. P.O. Box 218 • Assaria,Kansas67416

(

(

GREAT PLAINS


FOLIDING DRILL Effective 1-82

SOLID STAND® FOLDING DRILL

Feeder Channel Pages 30 through 32

Openers Pages 36 through 39

Tongue Pages 19 and 20

Drill Overview

Slide Frame Slide Hydraulics Pages 23 and 24 Page 26 Boxes

Wing Hydraulics Page 27

Lift Hydraulics Page 26

Pages 21 and 22

Press Wheels Pages 40 through 43

Pivot Post

Gauge Wheel Drive Pages 33 and 34

Pull Bars Pages 19 and 20

Transport Wheels Pages 23 and 24

Main Frame Pages 23 and 24

18

Gauge Wheels Page 35

Ref. No. Part No.

1 154-001 H 154-002 H

2 803-048 C 3 802-067 C 4 157-001 H 5 805-033C 6 802-048C 7 803-019 C 8 802-101 C 9 804-037C

10 803-049 C 11 812-009 C

I 12 890-007 C \, 890-055 C

13 890-019 C 14 111-001 H

15 803-032 C

1--20 21

20

/< 23 fS?-21

" "'22 "19 --~,

24

25 23

7 13

TONGUE and PULL BAR ASSEMBLY Description

Tongue Weldment, 24' drill (shown) Tongue Weldment, 30' drill

Jam Nut, hex, '!. "·10 Bolt, hex, '/."·10 x 4" long, full thread Pull Bar Slide Assembly Tongue Lock Pin w/hairpin cotter Bolt, hex, Y," -13 x 5);" long, Gr. 2 Locknut, hex, );"-13 Bolt, hex, %"-9 x 6" long, Gr. 5 Lockwasher, %" Nut, hex, %"-9 Combination Hitch Screw Jack w/pin, 24' drill (shown) Screw Jack w/pin, 30' drill Jack Pin Pull Bar Assembly

Jam Nu~ hex, 1%"-7

19

Great Plains SOUDSTAND


Great Plains SOLID STAND FOLDING DRIU Effective 1·82

ReI. No. Part No.

16 111-002 H .. 17 805-004 C

18 114-022 0 19 157.()()3 H

157-002 H 20 806-006C 21 804-022 C 22 803-021 C 23 802-096 C 24 804-027 C

.25 803-031 C

TONGUE and PULL BAR ASSEMBLY (Con't) Description

Pull Bar Adjustment Clevis Pull Bar Pin w/hairpin cotter (tongue end) Pull Bar Pin w/hairpin cotter (drill end) Transport Stabilizer Frame, right hand (shown) Transport Stabilizer Frame, left hand U·Bolt, % "-11 x 31\" x 5" long, Gr. 5 Lockwasher, %" Nut, hex, %"·11 Bolt, hex, 1"-8 x 21'," long, Gr. 5 Lockwasher, 1" Nut, hex, 1"-8

20

(

c

(

( \

(

Ref. No.

1 2 3 4 5 6 7 8 9

10 11

10

2

Part No.

118.Q03 H 158'()()2 H 802.Q34C 804'()15 C 803.Q2() C 817'()()1 C 801.Q03 C 804.()()4 C 803'()()1 C 816.()()4 C 816'()()1 C

__ 11

FRAME and BOXES-24' DRILL Description

Box Weldment-12' Frame Weldment-12' Bolt, hex, J'," ·13 x 1 Y. " long, Gr. 2 Lockwasher, J'," Nut, hex, J'," ·13 Sight Glass Screw, slothead, #10·24 x J'," long Lockwasher, #10 internal star Nut, hex, #10·24 Box End Ud Seal Box Ud Seal

21

Great Plains SOUD STAND

FOLDING DRILL Effective 1·82

Qty.

21drill 21drill 121box 121box 121box 1/box 21box 21box 21box

Ref. No. Part No.

1 118-100 H 2 158-001 H 3 802-034C 4 804-015 C

5 803.Q20C

6 817-001 C 7 801-003C 8 804-004C 9 803-001 C

10 816-004C 11 816-001 C

FRAME and BOXES-30' DRILL Description

Box Weldment-15' Frame Weldment-15' Bolt, hex, Y," -13 x 1 y." long, Gr. 2 Lockwasher, Y," Nut, hex, y, "·13 Sight Glass Screw, slothead, #10-24 x y," long Lockwasher, #10 internal star Nut, hex, #10-24

Box End Ud Seal Box UdSeaI

22



Qty.

21drill 2Idrill 151box 151box 151box 11box 2Ibox 2Ibox 2Ibox

(

(

Ref. No. Part No.

1 155.()()2 H

2 802.Q96C 3 804-027 C 4 803-031 C

5 800-050 C 6 803-032 C 7 805-033 C 8 8CIOM01C 9 800-011 C

10 156-003 H 11 816-012 C 12 822-014C 13 822-013 C 14 822-015C 15 822-016C

MAINFRAME, SLIDE and TRANSPORT AXLE Description

Transport Frame Bolt, hex, 1"-8 x 2)'," long, Gr. 5 Lockwasher, 1" Nut, hex, 1"-8 Depth Adjustment Stud Jam Nut, hex, 1)'."·7 Transport Lock Pin w/hairpin cotter Zerk, )'."·28 straight Spindle Pivot Bushing Post Spindle Post Spindle Seal Post Spindle Top Cone Post Spindle Top Cup Post Spindle Bottom Cup Post Spindle Bottom Cone

23



20

Great Plains SOLID STAND FOLDING DRILL Effective 1-82

MAINFRAME, SLIDE and TRANSPORT AXLE (Con't) Ref. No. Part No. Description

16 804-026C Flatwasher, %" SAE 17 803.Q29 C Nut, slotted hex, %"-14 18 805-016 C Cotterpin, 'f,," x 1%" long 19 890-032 C Post Spindle Hub Cap 20 156.0Q2 K Post Spindle Assembly-includes one each of items No. 8, 9 and 10 21 155-004 H Lower Railer 22 155-027 D Lower Railer Bushing 23 155-026 D Lower Roller Bolt 24 804-023C Lockwasher, '/.. " 25 803-027 C Nut, hex, '/.."-10 26 155-040 D Front Roller Shaft 27 155-042 D Front Roller 28 155-041 D Adjustment Spacer-front railer

29 803-024C Locknut, %"-11 30 156-001 H Slide Frame, left hand (shown)

156-002 H Slide Frame, right hand 31 156-005 D Slide Railer 32 156-007 D Slide Roller Spacer Tube 33 802-098 C Bolt, hex, 1"-8 x 4Y," long, Gr. 5 34 803-045 C NUl, Square, 1"-8 35 156-004 H Cylinder Ann 36 802-074 C Bolt, hex, 1"-8 x 6Y, " long, Gr. 5 37 155-003 H Inner Slide Tube 36 155-003 E Upper Roller 39 802-099 C Bolt, hex, ;1,"-13 x 3Y," long, Gr. 5 40 803-019 C Locknut, ;1,"-13 41 102.0Q2 K Transport Hub and Spindle Assembly 42 814-009 C Tire, 9.5 x 15, 12 ply, tube type 43 814-001 C Tube, 9.5 x 15 44 814.Q08 C Wheel, 15 x 8, e bolt 45 102-003 K Transport Wheel and Tire Assembly-includes one each of No. 42, 43 and 44

46 802-104 C Lug Bolt, ;1,"-20 UNF 47 201-003 D Single End Spindle, short 48 804-026 C Ratwasher, %" SAE 49 803.Q29C Nut, slotted hex, %"-14 50 805-016 C Cotterpin, 'f,," x 1)\" long 51 816-011 C Hub Seal 52 822-018 C Hub Inner Bearing Cone 53 822-019C Hub Inner Bearing Cup 54 812-014 C Hub Casting, six bolt 55 822-020 C Hub Outer Bearing Cup 56 822-021 C Hub Outer Bearing Cone 57 200-001 D Hub Grease Cup 58 200-001 K Hub Package-includes one each of No. 51 through 57 and six of No. 46

24

(

(

(

Ref. No. Part No.

1 156-006 H 156-005 H

2 806-006 C 3 804.Q22 C 4 803-021 C 5 156'()10 H 6 SOO-051 C 7 800'()14 C 8 800'()()1 C 9 802'()77 C

10 804-030 C 11 803-034 C 12 156.()()3 H 13 12O.()()1 E 14 802-054 C 15 803-046 C 16 803-032C 17 156'()()7 E 18 156-006 E

PIVOT POST ASSEMBLY Description

Pivot Post, left hand (shown) Pivot Post, right hand U-Bolt, % "-11 x 31;" x 5" long Lockwasher, %" Nut, hex, %" ~ 11 Roller Shaft Roller Shaft Bushing Roller Shaft Snap Ring Zerk, y." -28, straight Bolt, hex, 1Y, "-7 x 7" long, Gr. 5 Lockwasher, 1 y. " Nut, hex, 1%"-7 Post Spindle-see Transport Frame, page 20 Adjustment Unk Clevis, left hand thread Bolt, hex, %"-11 x 2" long, Gr. 2 Jam Nut, hex, 1 y. "·7, left hand thread Jam Nut, hex, 1 y. "-7, right hand thread Adjustment Unk CleviS, right hand thread Frame Adjustment Unk

25



ReI. No. Part No.

1 810-020 C _2 811-029 C 3 811-011 C 4 811-028 C 5 811-002 C 6 811-006 C 7 810-019C 8 810-021 C 9 802-097C

10 804-006 C 11 803-006C 12 811-031 C

5-

RJ---6

LIFT and SLIDE HYDRAULICS Description

Hydraulic Cylinder, 4" x 10" Tie Rod Hydraulic Hose, 'I." x 36" long Service Tee, '/," Cross, '/," Hydraulic Hose, '/," x 50" long Street Elbow, '/," Hydraulic Cylinder, 3" x 20" Tie Rod Flow Divider Valve Bolt, hex, Y. "-20 x 2'/," long, Gr. 2 Lockwasher, Y," Nut, hex, Y,"-2O Hydraulic Hose, '/," x 284" long

26


FOlDING DRILL Effective 1-82

Qty.

1 2 1 1 4 2 2 1 2 2 2

5

4

Ref. No_ Part No_

1 810'()18 C 2 810.()22 C 3 811-013 C 4 811-G27 C 5 811-026 C 6 811-033 C 7 811-G32 C K 811-034 C

8

/11 C@

I 3

WING HYDRAULICS

- - R' ht Hand Descnptlon 10" Tie Rod, Ig d 'd r 2;1," x LeltHan Hydraulic Cyl~n e, 2;1," x 10" Tie Rod,

lic Cylinder, Hydrau " 90' Swivel'Elbow, J. -Service Tee, % " Street Bbow, % Y," x 42" long Hydraulic Hose, .. " x 17" long Hydraulic Hose, ~"x 303" long Hydraulic Hose, ,

27

Great Plains SOLlDGSTDA~[

FOLDIN. Effective 1-82

aly_

1 1 2 2 1 1 1 2

21-~ 20-.b

J''-I

19-~~

Ref. No_ Pari No_

1 119-008H 119-007 H

2 806-004C 3 801-003 C 4 804-004 C 5 803-001 C 6 890-015C 7 816-008 C 8 890-016 C 9 802-006C

10 804-006C 11 803-OO7C 12 119-027D 13 802-018 C

<f I Jl-17 LIDS-STEPS and ATTACHMENTS

Description

Ud Weldmenl, 24' drill Ud Weldment, 30' drill Step Hanger U-bolt, %"-16 x 2" x 2%" long Screw, machine #10-24 x 'k" long Lockwasher, #10 internal star Nut, hex, #10-24 Bracket, anchor-welded to lid Latch, rubber Bracket, latch Boll, hex, y. "-20 x1'/," long, Gr_ 2 Lockwasher, y." Nut, hex, y,"-2O, self locking Hanger, step Bolt, hex, %"-16 xl" long, Gr_ 2

28



Great Plains SOUDSTAND FOLDING DRILL Effective 1·82

Ref. No. Part No.

14 804-013 C 15 803-014 C 16 119-015 D 17 802-079 C 18 804-011 C 19 806-002 C 20 804-015 C 21 803-020 C 22 119-001 H 23 807-001 C 24 110-015 D 25 110-016 D 26 802-005 C 27 803-006 C 26 802-007 C 29 803-011 C 30 119·109 A

119·110 A 31 805-014 C 32

LIDS-STEPS and ATTACHMENTS (Con't) Description

Lockwasher,% " Nut, hex, %'·16 Mount Angle Bolt, hex, %"·16 x 1 y." long, Gr. 5 Flatwasher, %" USS U·bolt, Y, "·13 x 3%" x 4%" long Lockwasher, %" Nut, hex, % "·13 Latch arm Ud Latch Spring Ud Lalch Strap Ud Lalch Spacer Boll, hex, Y,"·20 xl" long, Gr. 2 Nul, hex, y. "·20 Boll, hex, 'Y.: ·18 x ~, " long, Gr. 2 Nut, hex, self·locking, 'Y. .. ·18 Slep, 24' drill Slep, 30' drill Ud Hinge Pin Cotterpin, furnished with Ud Hinge Pin

29

(

(

(

Ref. No. Part No.

1 118-121 D 118-127 D 118-101 H 118-108 H 118-122 D 118-128 D 118-102 H 118-109 H 118-123 D 118-129 D 118-104 H 118-110 H 118-124 D 118-130 D 118-105 H 118-111 H 118-125 D 118-131 D

( 118-106 H 118-112 H 118-126 D 118-132 D 118-107 H 118-113 H

FEEDER CUP CHANNEL ASSEMBLY Description

Feeder Cup Channel, 6" spacing, 24' drill, left hand Feeder Cup Channel, 6" spacing, 24' drill, right hand Feeder Cup Channel, 6" spacing, 30' drill, left hand Feeder Cup Channel, 6" spacing, 30' drill, right hand Feeder Cup Channel, 7" spacing, 24' drill, left hand Feeder Cup Channel, 7" spacing, 24' drill, right hand Feeder Cup Channel, 7" spacing, 30' drill, left hand Feeder Cup Channel, 7" spacing, 30' drill, right hand Feeder Cup Channel, 7%" spacing, 24' drill, left hand

Feeder Cup Channel, 7';'" spacing, 24' drill, right hand Feeder Cup Channel, 7'12" spacing, 30' drill, left hand Feeder Cup Channel, 7'12" spacing, 30' drill, right hand Feeder Cup Channel, 8" spacing, 24' drill, left hand Feeder Cup Channel, 8" spacing, 24' drill, right hand Feeder Cup Channel, 8" spacing, 30' drill, left hand Feeder Cup Channe~ 8" spacing, 30' dril~ right hand Feeder Cup Channel, 10" spacing, 24' drill, left hand Feeder Cup Channel, 10." spacing, 24' drill, right hand Feeder Cup Channel, 10" spacing, 30' drill, left hand Feeder Cup Channe~ 10" spacing, 30' drill, right hand Feeder Cup Channel, 12" spacing, 24' drill, left hand Feeder Cup Channel, 12" spacing, 24' drill, right hand Feeder Cup Channel, 12" spacing, 30' drill, left hand Feeder Cup Channel, 12" spacing, 30' dril~ right hand

30

Great Pla;ns SOUDSTAND


Great Plains SOUDSTAND FOLDING DRILL Effective 1·82 (

FEEDER CUP CHANNEL ASSEMBLY (Con't) Ref. No. Part No. Description

2 120-103 D Drive Shalt, 6" spacing, 24' drill, left hand 120-109 D Drive Shaft, 6" spacing, 24' drill, right hand 120-100 D Drive Shaft, 6" spacing, 30' drill, left hand 120-119 D Drive Shaft, 6" spacing, 30' drill, right hand 120-104 D Drive Shaft, 7" spacing, 24' drill, left hand 120-110 D Drive Shalt, 7" spacing, 24' drill, right hand 120-101 D Drive Shaft, 7" spacing, 30' drill, left hand 120-120 D Drive Shaft, 7" spacing, 30' drill, right hand 120-105 D Drive Shaft, 7%" spacing, 24' drill, left hand 120-111 D Drive Shaft, 7% " spacing, 24' drill, right hand 120-115 D Drive Shaft, 7%" spacing, 30' drill, left hand 120-121 D Drive Shaft, 7%" spacing, 30' drill, right hand 120-106 D Drive Shaft, 8" spacing, 24' drill, left hand 120-112 D Drive Shaft, 8" spaCing, 24' drill, right hand 120-116 D Drive Shaft, 8" spacing, 30' drill, left hand

120-122 D Drive Shaft, 8" spacing, 30' drill, right hand 120-107 D Drive Shaft, 10" spaCing, 24' drill, left hand 120-113 D Drive Shaft, 10" spaCing, 24' drill, right hand 120-117 D Drive Shaft, 10" spacing, 30' drill, left hand 120-123 D Drive Shaft, 10" spacing, 30' drill, right hand 120-108 D Drive Shaft, 12" spacing, 24' drill, left hand 120-114 D Drive Shaft, 12" SpaCing, 24' drill, right hand (-120-118 D Drive Shaft, 12" spaCing, 30' drill, left hand 120-124 D Drive Shaft, 12" spaCing, 30' drill, right hand

3 1Q9.002 H Sprocket and Hub Weldment

4 822.Q06 C Bearing

5 800005C Snap Ring 6 llJ9.039 D Housing, bearing 7 800004C Snap Ring

8 800001C Zerk Fitting, y,"·28 9 109003 S Sprocket and Beari ng Assembly

(includes one each of items 3, 5, 6, 7, 8, and two each of item 4) 10 lQ9{)13 H Spool 11 8IJ5.{)23 C Roll Pin, ~,," x 1 V. " long 12 lQ9.001 D Housing, feeder cup 13 817.()()2 C Sprocket, nylon 14 8Q5.{)22 C Roll Pin, ~, .. xl" long 15 . 817-004 C Washer, nylon

16 109.Q06 D Retainer 17 801.()()2 C Screw, #10-16 x %" long, self·tapping 18 817.()03 C . Sleeve, Delrin 19 8Q4.031C Washer, retaining

20 805{)16 C Cotter Pin, 'I.." x 1 Y," long 21 1Q9.007 A Assembly, feeder cup (includes one each of items 12 thru 19) 22 1Q9.025 H Lock Weldment 23 120-062 H Mounting, seed gauge 24 819-005 C Gauge, feed adjustment 25 801'()()1 C Screw, brass ~2 x %" long i 26 120-061H Handle, seed adjustment '.

27 803-016 C Wing Nut, Y," ·13 28 804.()()1C Ratwasher, %"-SPL 29 822.()()8 C Bearing

31

Ref. No. Part No.

30 BOOOO3C 31 8Q5.()26 C 32 lOO<l45 D 33 lQ9.069 D 34 804012C 35 804013 C 36 802'()14 C 37 802.()32 C 36 804015 C 39 800004C 40 803.014 C 41 802-004 C 42 804006C 43 803006C

\

FEEDER CUP CHANNEL ASSEMBLY (Con't) Description

Snap Ring . Roll Pin,.1h II x 3;"" long

washer -Pivot Pin Pivot, adjustment handle Flatwasher, %" SAE Lockwasher, %" Capscrew, hex, % "·16 x 't. " long Capscrew, hex, %"·13 x 't." long Lockwasher, Y2" U·Bolt, %"·16 x 2" x 2r." long Nut, hex, %"·16 Bolt, % "·20 x 't." long Lockwasher, y." Nut, hex, % ".2f\

32



Ref. No. Part No.

1 12Q.041 H 12Q.042 H

2 120043 H 120-044 H

3 120037 H 120-038 H

4 120053 D 5 8Q6.002 C 6 804015 C 7 803-020 C 8 802-062 C 9 804022C

10 803-021 C 11 804021C 12 802@4C 13 1CJ9.043 K 14 12().()()1 E

15 12().()()3 E 16 803-032 C 17 120002 E 18 802-054C ,

\ 19 120033 H 20 822'()10 C 21 802.()45 C

22 8Q6.002C

GAUGE WHEEL DRIVE Description

Pivot Mounting Qeft hand side of drill-shown) Pivot Mounting (right hand side of drill) Pivot Mounting, short Qeft hand side of drill-shown) Pivot Mounting, short (right hand side of drill) Hanger, gauge wheel Qeft hand side of drill-shown) Hanger, gauge wheel (right hand side of drill) Mounting Channel

U·Bolt·Y, "·13 x 3Y," x 4Y," long, Gr. 2 Lockwasher, )\" Nut, hex Y, "·13 Bolt, hex, %"·11 x 5" long, Gr. 5 Lockwasher, %" Nut, hex %"·11 Flatwasher, %" SAE Bolt, hex, y, "·13 x 1~" long Gr. 2

Great PJains SOUDSTAND


Gauge Wheel TIre and Wheel Assembly, ~ncludes one each of No.'s 45, 46 and 47). Upper Gauge Wheel Clevis Gauge Wheel Adjustment link Jam Nut, hex, 1~"·7 Lower Gauge Wheel Clevis Bolt, hex, %"·11 x 2" long, Gr. 2 Axle, gauge wheel Bearing, 1 Y," bore, 2 bolt flange Bolt, hex, y, "·13 x 5" long Gr. 5 Sprocket, #50 x 15f x 1 Y," bore

33

Great Plains SOUDSTAND FOLDING DRIU Effective 1·82 (

GAUGE WHEEL DRIVE (Con't) Ref. No. Part No. Description

23 8Q5.029 C Roll Pin, '/,: x 2%" long 24 12Q.005 D . Idler Arm

25 109-064 0 Idler Disk

26 1Q9.()14 0 Tube, Speed Change

27 822-005 C Bearing, sprocket-speed change 28 1J09.OO1C Chain, 20-50 x 36 links-37 pitch 29 IJ09.OO4 C Chain, 20-50 x 40 Iinks-44 pitch

30 12(}()40 H Bracket, jackshaft bearing Qeft hand-shown)

12Q.039 H Bracket, jackshaft bearing (right hand) 31 12(}{)2O H Idler Arm 32 802.<J11 C Bolt, hex, '/,,"·18 x 1)'," long, Gr. 2

33 8Q4.009C Lockwasher, 5fse" 34 8Q3.008C Nut, hex, '/,:·18 35 822'()()7 C Bearing, 1" bore, 2 bolt flange 36 1Q9.031 0 Key, Y," x 1Y," long 37 12Q.03() 0 Jackshaft, 31)'," long (2O'Orill)

12(}{)11 D Jackshaft, 17%" long (14' Drill)

36 808003C Sprocket, 39T x 1" bore 39 1Q9.005 H Sprocket Hub, 20T and 35T 40 8Q8.004C Sprocket, 1ST x 1" bore

41 8Q9.005C Chain, 20-50 x 48 Iinks-49)', pitch

42 802.<J35 C Bolt, hex, )',"·13 x 1%" long, Gr. 2 ( 43 804.()16 C Flatwasher, )'," SAE 44 8Q3.017 C Lug Nut, % "·20,-90· seat

45 814-005 C Rim, wheel, 6 x 15-5 hole

46 814.()()4 C Tube, inner, 9.5L x 15 47 814.<J11 C Tire, 9.5L x 15-8 ply 48 89O.<J22 C Acre Counter (14' Drill)

890.Q23C Acre Counter (20' Drill)

49 8Q3.023C Jam Nut, hex, '/,"·11 50 800006C Sprocket, 19T x 1" bore 51 1Q9.()45 S Speed Change Hub and Bearing Assembly-

includes one each of No. 26 and 39, two each of No. 27.

(

34

13

(

Ref. No. Part No.

1 12G<J42 H 2 12O-<l44 H 3 12(}{)48 H 4 120-{)53 D 5 800002 C 6 804-{)15 C 7 803-mOC 8 802-062C 9 804-Q22C

10 8Q3-D21C 11 804-{)21 C 12 802-034C 13 109-043 K

14 120-001 E 15 120-003 E 16 803-032C 17 120-002 E 18 802-054C 19 120-D33 H

( .20 822-010 C 21 802-045C 22 814-005 C 23 814-004 C 24 814-011 C 25 803-017 C

~25

RIGHT HAND GAUGE WHEEL ASSEMBLY Description

Pivot Mounting (right hand) Pivot Mounting, short (right hand) Hanger, gauge wheel Mounting Channel U·Bolt, '/,"·13 x 3'/," x 4)'," long, Gr. 2 Lockwasher, Y," Nut, hex y, "·13 Bolt, hex, %"·11 x 5" long, Gr. 5 Lockwasher, 'I." Nut, hex, %"·11 Flatwasher, 'I." SAE Bolt, hex, '/,"·13 x 1%" long, Gr. 2 Gauge Wheel TIre and Wheel Assembly

includes one each of No. 22, 23 and 24. Upper Gauge Wheel Clevis· left hand thread Gauge Wheel Adjustment Unk Jam Nut, hex, 11."·7 Lower Gauge Wheel Clevis·right hand thread Bolt, hex, % "·11 x 2" long, Gr. 2 Axle, Gauge Wheel Bearing, 1'/," bore, 2 bolt flange Bolt, hex, )', "·13 x 5N long, Gr. 5 Rim, Wheel, 6 x 15-5 hole Tube, Inner, 9.5L x 15 TIre, 9.5L x 15--8 ply Lug Nut, )', "·20,_90" seat

35



(

\

(

Ref. No.

1 2 3 4 5 6 7 8 9

10 11 12 13 14 15

Part No.

8Q6.004C

8Q4.013 C 80:J.014 C 121-025 D 121.021 D 12Hl11 K 12Hl01 D 802'()78 C

804.Q06C 803.Q06C 807002 C 107.027 D 800.Q09C 81&002 C

3

40

35 36 15" I \( ~\



39

38 \

>~

24 !.~~' \ ~ .. ~ /~I -34 / ~-29 ~'~14 '" 23~ I~I A I 13 1-30

,~ \25 )Q'V \ '. 28 / 41" , III __ 26

42 31 11~-27 ~ ~~

\ ~--2'9 33

SINGLE DISK OPENER Description

Mounting Tube-Welded to box U-Bolt, '/."·16 x 2" x 2'/." long

Lockwasher, %" Nut, hex, %"-16 Spring Rod Casting Clip Double Spring Rod casting Spring casting Mounting Assembly-includes items 2 through 6 Double Disk Spring Bar Bolt, hex, Y. "·20 x '/," long, Gr. 5 Lockwasher, y." Nut, hex. Y."-20 Spring, 16" long x 43 coils Spring Rod Clip Hose Clamp, 1'/," Dia., #26 Drop Tube, short

36

Great Plains SOUDSTAND FOLDING DRILL SINGLE DISK OPENER (Con't) Effective 1·82 ( Ref. No. Part No. Description

16 121·012 H Mounting Arm, Right Hand (shown) 121·013 H Mounting Arm, Left Hand

17 107-081 D U·Mount, Disk Arm

18 802-046 C Bolt, hex, % "·13 x 5%" long, Gr. 2 19 8(J3.Q19 C Locknut, hex, y, "·13

20 107-083 D Mounting Strip-6" spacing 107-085 0 Mounting Strip-7" spacing

121-018 D Mounting Strip-7V," spacing 107-086 0 Mounting Strip-8" spacing 107-0870 Mounting Strip-10" spacing

107-088 0 Mounting Strip-12" spacing

21 802-083 C Whiz Bolt, hex, %"·13 x 1)!." long, Gr. 5

22 803-037C Whiz Nut, hex, %"·13" 23 802-081 C Bolt, hex, %"·16 x 4\:," long, Gr. 5 24 8(J3.Q13 C Locknut, hex, %"·16

25 802-010 C Bolt, hex, '/,,"·18 x 1%" long, Gr. 2

26 804.Q09 C Lockwasher, '1,. " 27 803.Q08 C Nut, hex, '/,."·18

28 122-025 D Mounting Channel, press wheel spring

29 122-0120 Spring Bar, press wheel

30 807-003 C Spring, 4%" long x 12)', coils 31 805.Q2O C Cotterpin, y." x 1" long

32 121-014 H Scraper Assembly, Right Hand (Shown)

121-015 H Scraper Assembly, Left Hand

33 8(J3.Q24 C Locknut, hex, %"·11 ( 34 800.Q11 C Rivet, %. " x %" long Button Head 35 107-060 0 Bearing Flange (shown)

107-095 0 Bearing Flange

36 822-002 C Bearing

37 820.Q01C Disk

36 115-063 0 Bolt, hex, %"·18 x 2)'," long, Gr. 5 39 107-025 0 Dust Cover

40 107.Q08 S Single Disk and Bearing Assembly -Includes one each of No. 35, 36, 37, 36, 39 and six of No. 34.

41 804.Q22 C Lockwasher, %" 42 803.Q22C Nut, hex, %"-18

37

Rei. No. Part No.

1 2 800004C 3 803{)37 C 4 8()3.{)14 C 5 12Hl25 D 6 12Hl21 D

812..()12C 7 12H)11 K 8 121..()()1 D 9 802"()78C

10 804..()()6 C 11 803..()()6 C 12 807..()()2 C 13 107-027 D 14 800..()()9 C

( 15 816..()()3C 16 10H156 H 17 107..()81 D 18 802{)46C 19 8()3.{)19 C

DOUBLE DISK OPENER Description

Mounting Tube-welded to box u.aolt, l's "·16 x 2" x 2'/." long Whiz Nu~ hex, y, "·13 Nut, hex, J'."·16 Spring Rod Casting Clip Double Spring Rod Casting Triple Spring Rod Casting Mounting, spring casting, (includes items 2 through 6) Bar, double disk spring Bolt, hex, ~ "·20 x %" long Gr. 5 Lockwasher, r. • Nut, hex, ~ "·20 Spring, 16" long x 43 coils Clip, spring rod Hose Clamp Hose, rubber, 12)',' long compressed Arm, double disk mounting U-Mount, disk arm Bolt, hex, )', "·13 x 5'/," long Locknut, hex, y, "·13

38



28

Great Plains SOUD STAND FOLDING DRILL Effective 1-82 DOUBLE DISK OPENER (Con't) (

Ref. No. Part No. Description

20 107-083 D Strip, mounting- 6" spacing 107-085 D Strip, mounting- 7" spacing 12Hl18 D Strip, mounting- 7'/," spacing 107-085 D Strip, mounting- 8" spacing 107-087 D Strip, mounting-10" spacing 107-085 D Strip, mounting-12" spacing

21 802-083C Whiz Bolt, hex, '/,"-13 x 1Y." long, Gr. 5 22 804-009 C Lockwasher,Yts" 23 8Q3.008C Nut, hex, ~6"w18 24 82().()Q2 C Disk, flat 25 822.Q03 C Bearing 26 107-060 D Bearing Flange (shown)

107-095D Bearing Flange 27 800-010 C Rivet, button head, 'f,," x'/," long 28 107-054 S Assembly, flat disk

(includes one each of items 24, 25, 26 and six each of item 27) 121-022S Chrome Double-Disk Assembly (optional)

29 802·102 C Bolt, hex head, '!."-11 x 1%" long, Gr. 5, NYlOCK 30 107-084 D Cap, hub

31 122-012 D Bar, press wheel spring 32 807.Q03C Spring, 4%" long x 12'/, coils 33 122'()25 D Mounting Bar, press wheel spring

34 107'()79 D Mount, scraper (' 35 107'()75 D Scraper

36 804'()11 C Flatwasher, %" USS 37 802'()10 C Bolt, hex, ~161f·18x 1Y4" long 36 8Q5.()20 C Pin, cotter, %." x 1" long 39 802'()16 C Step Bolt, %"-16 x 1" Ig. Gr. 5 40 803-013 C locknut, bex, %"-16 41 802-081 C Bolt, Hex Head, %"-16 x 4'/," long, Gr. 2

121.()Q9 A Double Disk Row Assembly-Front (Items Not Included: 1,7, 20,24,25,26 and 27)

121'()10 A Double Disk Row Assembly-Rear (Shown) (Items Not Included: 1,7,20,24,25,26 and 27)

42 804.()13 C lockwasher, %"

(

39

(

Ref. No. Part No.

1 8()4.()13 C 2 803-014 C 3 122'()10 C 4 814-007 C 5 822-023 C 6 802'()14 C 7 122.()()2 S

8 8OWJ9C 9 8Q5.()10 C

10 122.()Q5 H 11 803-012 C 12 801.()Q7 C 13 122.()2() A

PRESS WHEEL ASSEMBLY -2" x 13" Description

Lockwasher, %" Nut, hex, % "·16 Rim Half Tire, rubber, 2" x 13 11

Bearing, press wheel Bolt, hex, % "·16 x '!." long Assembly, press wheel--lncludes two of item 3,

one each of items 4 and 5, and seven each of items 1, 2 and 6. Pin Hair Pin Cotter Arm, press wheel

Jam Nut, hex, ".·16 Set Screw, square head, ".·16 x 'Ia" long Assembly, press wheel and hanger

Includes one each of items 7 thru 12

40



13

Ref. No. Part No.

1 122-004 H 2 122-024 H 3 122~7H

122.(]()8 H

4 122-021 D 5 814-013 C 6 81~7C

7 802-023 C

( 8 802-014C 9 804-013C

10 804-014 C 11 122-002 S

/

/' /~

8

PRESS WHEEL ASSEMBLY-2" X 13" DOUBLE "V" Description

Arm, press wheel, double "V" left half Arm, press wheel, double "V" right half Angle Bar, narrow (2%" end to end) Angle Bar, wide (3'f." end to end) Bar, adjustment Rim Half, 2" x 13" Tire, rubber, 2" x 13" Bearing

Bolt, hex, % "·16 x 't." long Lockwasher, %" Nut, hex, %"·16 Assembly, press wheel, 2" x 13" Oncludes one each of items 6 and 7, two each of item 5, and seven each of items 8, 9 and 10)

41


FOlDING DRIll Effective 1·82

Great Plains SOUDSTAND FOLDING DRILL Effective 1·82 PRESS WHEEL ASSEMBLY-2" x 13" DOUBLE "V" (Con't)

Ref. No. Part No.

12 805-011 C 13 805-010 C 14 802'{)11 C 15 8Q3.008C 16 803.{)14 C 17 802.Q22 C 18 803.{)13 C 19 801.{)11 C 20 803.{)12 C 21 122.{)21 A

122.Q23 A

Description

Pin Pin, hair cotter Bolt, hex, '/,."·18 x 1%" long Gr. 2 Locknut, hex, '/,,"-18 Spacer, % "-16 nut Bolt, hex, %"·16 x 1V," long, Gr. 2 Locknut, hex, %"-16 Set Screw, %"-16 x 'I." long, square head, oval point Jam Nut, hex, %"-16 Assembly, press wheel and hanger-NARROW

(Incluaes all items shown with narrow angle bar, item 3) Assembly, press wheel and hanger-WIDE

Oncludes all items shown with wide angle bar, item 3)

42

(

(

,.

( ,

Ref. No.

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15

Part No.

122.()()6 H 122.()28D

814010 C 822.011 C 802.Q07C 804009C 803.Q06C 122.Q03 S

803.Q12 C

802.017 C 802.011 C 803.Q14 C 805.Ql1 C 805.Ql0 C 122.Q22 A


FOLDING DRILL

15

, K ~'

, I ,

I

--1

I , I

8

PRESS WHEEL ASSEMBLY-4" X 12" V·GROOVE Description

Hanger Half, 4" x 12" VGroove press wheel Rim Half lire, rubber, 4" x 12" V.Groove Bearing, press wheel, double ended Bolt, hex, %."·18 x 0/." long, Gr. 2 Lockwasher, !f'8 " Nut, hex, %."·18 Assembly, press wheel and bearing ~ncludes one each of items 3 and 4, two each of item 2, and seven each of items 5, 6, and 7) Jam Nut, hex,'/a"·16 Bolt, hex, %"·16 xl" long Bolt, hex, %,"·18 x 1 Y," long, Gr. 2 Spacer, %"·16 hex nut Pin, spring bar Pin, hair cotter Assembly, press wheel and hanger ~ncludes one each of items 8 \hru 14, and two each of item 1)

43

Effective 1·82

Ref. No. Part No.

1 8Q3.OO8 C

2 804-009C 3 804010 C 4 802.{)()9 C

5 817-005 C 6 81MlO6 C 7 116-018 A

8 116'()19 A



NOTE: FOR PROPER DEPTH. CONTROL WHEEL OPERATION, OUTSIDE DOUBLE· DISK SCRAPERS ARE REQUIRED.

7

RUBBER·TIRED DEPTH CONTROL WHEEL Description

Nut, hex, % "·18 Lockwasher, %" Flatwasher, %" USS Bolt, carriage, r.."·18 x 1%" long Depth Wheel, plastic TIre, rubber, 1.38 x 10.25 Rubber Depth Wheel Assembly-

includes 2 each of items 1 thru 4, and 1 each of items 5 and 6) Double·Disk Scraper Assembly

44

(

Ref. No. Part No.

1 116{)41 D

( 2 116{)42 D

3 802-092 C 4 8Q4.036 C

5 804-009 C 6 8Q3.OO8 C 7 802{)16 C 8 804{)12 C

9 804{)13 C 10 803{)14C

11 107{)75 D

12 802{)08 C

13 116{)19 A

OUTSIDE DOUBLE· DISK SCRAPER Description

Scraper Mount Outside Scraper Tab

Carriage Bolt, ')\. "-18 x %" long, Gr. 2 Flatwasher, ')\." SAE

Lockwasher, Sf.t6" Nut, hex, ')\."-18 Step Bolt, %"-16 x 1" long, Gr. 5 Flatwasher, %" SAE Lockwasher, %" Nut, hex, %"-16 Scraper, inside

Bolt, hex, ')\,"-18 x 1%" long, Gr. 2 Double Disk Scraper Assembly Oncludes items No.1 thru 10)

45


FOLDING DRIli. Effective 1-82

~"

Ref. No. Part No.

1 113.Q61 H 113.(J6() H

2 113·1100 3 805-024 C 4 806..()()6 C 5 804-022 C 6 803-021 C 7 802·113 C 8 803.(J15 C 9 804.(J14 C

10 805-042 C 1f 113-063 H 12 800-001 C 13 113-062 H 14 113-064 H

113-065 H 15 802-008 C 16 803-043 C 17 801.(J13 C 18 113.(J70 H 19 113-007 H

( 20 107-096 0 21 802-059 C 22 802-045 C 23 804.(J15 C 24 803-020 C

FOLDING HYDRAULIC MARKER Description

Folding MaJ1<er Mount-right (shown) Folding Marker Mount-left Marker Body Pivot Roll Pin, 'f,: x 1}'," long U·Bolt, %"·11 x 3}'," x 5" long Lockwasher, %" Nut, hex, %"·11 Bolt, hex, '/,:·14 x 1'/." long, Gr. 5 Nut, hex, '/,:·14 Lockwasher, 'f,e" Lock Pin w/hairpin Cotler Marker Arm Zerk, y." ·28, straight MaJ1<er Lever MaJ1<er Extension-right (shown) MaJ1<er Extension-left Bolt, hex, %."·18 x 1" long, Gr. 2 Whiz Nut, %."·18 Set Screw, hex socket, }', "·13 x 1}'," long Disk Bar Marker Disk and Bearing Assembly Baaring Flange Dust Cover Bolt, hex, %"·11 x 3" long, Gr. 5 Bolt, l\ "·13 x 5" long, Gr. 5 Lockwasher, }'," Nut, hex, l\ "·13

46



Great Plains SOUDSTAND FOLDING DRIU Effective 1·82

Ref. No. Part No.

25 113.()67 H 113-066 H

25 113·111 D 27 890-018 C 28 113·101 D 29 890.()6() C 30 803-008 C

( FOLDING HYDRAULIC MARKER (Can't)

Description

Extension Pivot Bracket-right (shown) Extension Pivot Bracket-left Hinge Pivot Bar Utility Clevis, 't.," Chain, Yo" x 37 links Tumbuckle, 't.," x 4};", w/pins Nut, hex,5ft/-18

(

47



13

L3 14

/ 2

/ 1- j) I, 1-, 3-

2 11 1--

SINGLE DUAL

Q MARKER

MARKERS Q

MARKER HYDRAULICS Ret No. Part No. Description

1 810-005 C Hydraulic Cylinder, 2" x 8" Single Acting 2 811-013 C Pipe Swivel, %" MNPT x %" FNPT, 90', Y,," orifice 3 811-036C Hydraulic Hose, 24' drill

811-035 C Hydraulic Hose, 30' drill 4 811-009 C Service Tee, %", Female 5 810-023 C Double Selector Valve 6 113-1250 Double Selector Valve Mount 7 802-114 C Bolt, hex, %"-16 x 2Y, " long, Gr. 2 8 804-013 C Lockwasher, %" 9 803-014 C Nut, hex, %"-16

10 811-037 C Fitting, %" F swivel x '/," M 11 811-032 C Hydraulic Hose, '/." x 16" long 12 811-033C Hydraulic Hose, '/." x 42" long 13 811-034C Hydraulic Hose, '/." x 303" long (existing) 14 113-130 0 Hydraulic Hose Retainer 15 810-020 C Slide Cylinder (existing)

Great Plains Manufacturing, Inc.Corporate Office: P.O. Box 5060Salina, Kansas 67402-5060 USA

a great plains...introduction your great plains folding drill is designed to give you many years of...

Documents